HORIZON-ODU-MIB

All MIBs › HORIZON-ODU-MIB

Category: Domain: Optical Transport, Technology: Optical Transport, Telephony and VoIP

Description: Comverse Horizon Outdoor Unit (ODU) MIB for managing outdoor radio transmission units in Horizon microwave systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HORIZON-ODU-MIB?

HORIZON-ODU-MIB is a legacy proprietary MIB (built on HORIZON-MIB) for the ODU (Outdoor Unit) of a microwave radio link. Its objects cover a system-reset action (resets NIC, modem, and radio), a save-MIB action, operational status, air-interface encryption, system redundancy, current/licensed speed, system mode, upgrade-licensed-speed, redundancy mode/override/link-status/standby-Ethernet-state/state-switch, and serial/assembly numbers for the unit, IF, RF, NCC (Network Control Card?), and diplexer subassemblies, plus an OMNI version number. As a status/configuration MIB it lets an administrator confirm radio-link redundancy state and licensed capacity on this legacy microwave ODU. It is deployed on legacy microwave-radio Outdoor Unit (ODU) equipment. Engineers can download the HORIZON-ODU-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HORIZON-ODU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DragonWave Horizon-series microwave radio Outdoor Unit (ODU)

Monitoring Examples

An administrator checks hzOduSystemRedundancyLinkStatus and hzOduSystemCurrentSpeed to confirm radio-link redundancy state and current capacity on this legacy microwave ODU.

What Can Be Monitored

radio-link redundancy state and licensed/current capacity

Imported Objects

From HORIZON-MIB

horizon

OBJECT-IDENTITY

From IF-MIB

OBJECT-TYPE
ifIndex	OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks

From SNMPv2-MIB

snmp	OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF coldStart	1.3.6.1.2.1.11.0.0			A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered.
horizonOdu	1.3.6.1.4.1.7262.2.2
hzOduAam	1.3.6.1.4.1.7262.2.2.1.5
INT hzOduAamActive	1.3.6.1.4.1.7262.2.2.8.2.5	INTEGER	read-only	Indicates aam is active and system running on lowest modulation
NTF hzOduAamActiveClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.8			Adaptive modulation on system running on higher modulation
CTR hzOduAamActiveCount	1.3.6.1.4.1.7262.2.2.8.2.6	Counter	read-only	Indicates the approximate number of seconds AAMActive alarm has been active.
INT hzOduAamActiveTrap	1.3.6.1.4.1.7262.2.2.9.8	INTEGER	read-write	Enables or disables the aamActive trap.
NTF hzOduAamActiveV1Trap	1.3.6.1.4.1.7262.2.2.9.0.7			Adaptive modulation on and system running on lowest modulation
INT hzOduAamConfigMismatch	1.3.6.1.4.1.7262.2.2.8.2.3	INTEGER	read-only	In the near end Automatic Adaptive Modulation(AAM) feature set to on and in peer it is set to off
NTF hzOduAamConfigMisMatchClearV1Trap	1.3.6.1.4.1.7262.2.2.9.0.6			Adaptive modulation configuration mismatch cleared
CTR hzOduAamConfigMismatchCount	1.3.6.1.4.1.7262.2.2.8.2.4	Counter	read-only	Indicates the approximate number of seconds AAMConfigMismatch alarm has been active.
INT hzOduAamConfigMismatchTrap	1.3.6.1.4.1.7262.2.2.9.7	INTEGER	read-write	Enables or disables the aamConfigMismatch trap.
NTF hzOduAamConfigMisMatchV1Trap	1.3.6.1.4.1.7262.2.2.9.0.5			Adaptive modulation configuration mismatch
INT hzOduAamEnable	1.3.6.1.4.1.7262.2.2.1.5.1	INTEGER	read-write	Indicates whether Automatic Adaptive Modulation(AAM) is enabled.
INT hzOduAirInterfaceEncryption	1.3.6.1.4.1.7262.2.2.1.1.4	INTEGER	read-only	OBSOLETE. This enables encryption on the air interface.
hzOduAlarms	1.3.6.1.4.1.7262.2.2.8
hzOduAtpc	1.3.6.1.4.1.7262.2.2.1.4
INT hzOduAtpcAutoDisabled	1.3.6.1.4.1.7262.2.2.8.2.13	INTEGER	read-only	Indicates the ATPC set to off and system transmit at coordinated power.
CTR hzOduAtpcAutoDisabledCount	1.3.6.1.4.1.7262.2.2.8.2.14	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduAtpcAutoDisabledTrap	1.3.6.1.4.1.7262.2.2.9.30	INTEGER	read-write	Specifies whether this trap is to be sent or not
INT hzOduAtpcConfigMismatch	1.3.6.1.4.1.7262.2.2.8.2.7	INTEGER	read-only	In the near end Automatic Transmit Power Control(ATPC) feature set to on and in peer it is set to off
NTF hzOduAtpcConfigMismatchClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.10			ATPC configuration mismatch is cleared
CTR hzOduAtpcConfigMismatchCount	1.3.6.1.4.1.7262.2.2.8.2.8	Counter	read-only	Indicates the approximate number of seconds AtpcConfigMismatch alarm has been active
INT hzOduAtpcConfigMismatchTrap	1.3.6.1.4.1.7262.2.2.9.9	INTEGER	read-write	Enables or disables the trap.
NTF hzOduAtpcConfigMismatchV1Trap	1.3.6.1.4.1.7262.2.2.9.0.9			ATPC is set to on at near end however in the far end it is set to off.
INT hzOduAtpcCoordinatedPowerDbm	1.3.6.1.4.1.7262.2.2.1.4.2	INTEGER	read-write	This defines the coordinated power level. The value is multiplied by 10. e.g. A display of 133 is actually 13.3 dBm.
INT hzOduAtpcEnable	1.3.6.1.4.1.7262.2.2.1.4.1	INTEGER	read-write	Indicates whether Automatic Transmit Power Control (ATPC) is enabled.
NTF hzOduAtpcTxAtCoordinatedPwrClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.49			Atpc is enabled in the system and it is back to regular power.
NTF hzOduAtpcTxAtCoordinatedPwrV1Trap	1.3.6.1.4.1.7262.2.2.9.0.48			Atpc is enabled in the system and it is transmitting at maximum power.
hzOduAuthentication	1.3.6.1.4.1.7262.2.2.2
INT hzOduAuthenticationFailureAction	1.3.6.1.4.1.7262.2.2.2.4	INTEGER	read-write	This sets the authentication failure action for the system. Block traffic will block all user traffic including remote management access. Pass traffic will allow all user traffic to be sent and recieved
INT hzOduAuthenticationMode	1.3.6.1.4.1.7262.2.2.2.3	INTEGER	read-write	This sets the authentication mode for the system.If configured for unique authentication, an horizon node only exchanges user traffic with one other horizon node. The serial number is used in this case. If configured for group authentication, an horizon node exchanges user traffic with another horizon node of the same group and uses the authentication keys.
INT hzOduAutomaticLinkReestablish	1.3.6.1.4.1.7262.2.2.14.1.2	INTEGER	read-write	If this feature is enabled, the link will be automatically reestablished. If this feature is disabled, the user must explicitly use the manualReestablish object to bring the link back up
hzOduCalendar	1.3.6.1.4.1.7262.2.2.7
INT hzOduClearAlarmCounters	1.3.6.1.4.1.7262.2.2.8.1	INTEGER	write-only	Clears the alarm counters for the specified group
INT hzOduColdStartTrap	1.3.6.1.4.1.7262.2.2.9.3	INTEGER	read-write	Specifies whether this trap is to be sent or not
INT hzOduCosDefaultValue	1.3.6.1.4.1.7262.2.2.13.9	INTEGER	read-write	Default CoS value assigned to the ethernet frames that don't have VLAN or Q-in-Q tag.
INT hzOduCosExpediteQueue	1.3.6.1.4.1.7262.2.2.13.6	INTEGER	read-write	This sets the user queue operation mode. (a) In expedite mode, any Queue can be assigned 100% of CIR. Queue 4 is serviced first and queue 1 is servcied last.(b) In non expedite mode, the sum of all CIRs must be equal to 100%. In this mode higher priority queues will be serviced first until that queue is emptied or the defined CIR is reached.
STR hzOduCoSQinQiTag	1.3.6.1.4.1.7262.2.2.13.3	DisplayString	read-write	Sets the value of the Q-in-Q inner tag. This tag is also used to classify the non-Q-in-Q VLAN. Default value is 0x8100.
STR hzOduCoSQinQoTag	1.3.6.1.4.1.7262.2.2.13.4	DisplayString	read-write	Sets the value of the Q-in-Q outer VLAN tag. Default value is 0x8100.
STR hzOduCosQueueCBS	1.3.6.1.4.1.7262.2.2.13.8	DisplayString	read-write	Comitted Burst Size (CBS) for CoS queues 1 to 4. CBS is the percentage of total packet buffer size. The sum of CBS's of all 4 queues must be equal to 100. Minimum CBS assignable to any queue is 1.
STR hzOduCosQueueCIR	1.3.6.1.4.1.7262.2.2.13.7	DisplayString	read-write	Committeed Information Rate (CIR) assignments for CoS queues 1 to 4. CIR is assigned as the percentage of system current speed. When expedite queue is enabled any queue can be assigned 100% bandwidth. When expedite queue is disabled the sum of CIR of all queues should be 100.
STR hzOduCosQueueMapping	1.3.6.1.4.1.7262.2.2.13.5	DisplayString	read-write	User queue assignments for CoS values 0 to 7. There are 4 coS queues. Their corresponding queue numbers are 1,2, 3, where 1 is the lowest priority queue and 4 is the highest priority queue. CoS to queue mapping example: 1 1 2 2 3 3 4 4.
INT hzOduCosType	1.3.6.1.4.1.7262.2.2.13.2	INTEGER	read-write	Indicates the class of service tag type. Based on the setting Horizon will use the CoS value in the VLAN tag, or Q-in-Q inner VLAN tag, Q-in-Q outer VLAN tag, or DSCP tag.
INT hzOduCutThroughProcessing	1.3.6.1.4.1.7262.2.2.13.10	INTEGER	read-write	Sets cut through processing on/off.
STR hzOduDate	1.3.6.1.4.1.7262.2.2.7.1	DisplayString	read-only	A string in the format as follows: XX/YY/ZZ Where XX = day of month (range 01 to 31) YY = month of year(range 01 to 12) ZZ = year (range 01 - 99)
IP hzOduDefaultGateway	1.3.6.1.4.1.7262.2.2.3.5	IpAddress	read-only	The default gateway for the network interface card
STR hzOduDiplexerAssemblylNo	1.3.6.1.4.1.7262.2.2.1.3.1.10	DisplayString	read-only	A textual string containing assembly no of the Diplexer.
STR hzOduDiplexerSerialNo	1.3.6.1.4.1.7262.2.2.1.3.1.9	DisplayString	read-only	A textual string containing Serial no of the Diplexer.
hzOduEnetPort1	1.3.6.1.4.1.7262.2.2.4.1
INT hzOduEnetPort1AdminState	1.3.6.1.4.1.7262.2.2.4.1.2.5	INTEGER	read-only	Configure the port1 interface media.
hzOduEnetPort1Alarms	1.3.6.1.4.1.7262.2.2.8.3.1
INT hzOduEnetPort1AutoNegotiation	1.3.6.1.4.1.7262.2.2.4.1.2.1	INTEGER	read-write	port1 Turns auto-negotiation on or off. Turning off results in the interface defaulting to 100BaseT, Full Duplex.
INT hzOduEnetPort1AutoNegotiationStatus	1.3.6.1.4.1.7262.2.2.4.1.3.2	INTEGER	read-only	Indicates the port1 AutoNegotiation status.
CTR hzOduEnetPort1BandwidthUtilizationThresholdCount	1.3.6.1.4.1.7262.2.2.8.3.1.4	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
INT hzOduEnetPort1BandwidthUtilizationThresholdExceeded	1.3.6.1.4.1.7262.2.2.8.3.1.3	INTEGER	read-only	The threshold for the percentage of available bandwidth has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.
INT hzOduEnetPort1BandwidthUtilizationThresholdExceedTrap	1.3.6.1.4.1.7262.2.2.9.13	INTEGER	read-write	Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
STR hzOduEnetPort1BandwidthUtilizationThresholdParameters	1.3.6.1.4.1.7262.2.2.4.1.2.10	DisplayString	read-write	A read-write string: The percentage of available bandwidth threshold and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the threshold point in percent, the number of seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.
INT hzOduEnetPort1BWUtilization	1.3.6.1.4.1.7262.2.2.4.1.4.7	INTEGER	read-only	The carried load over link capacity for port1.
NTF hzOduEnetPort1BwUtilizationThresholdExceededClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.17			The condition has cleared. The ethernet bandwidth threshold is now below its threshold value.
NTF hzOduEnetPort1BwUtilizationThresholdExceededV1Trap	1.3.6.1.4.1.7262.2.2.9.0.16			The ethernet bandwidth threshold has been detected above its threshold value.
NTF hzOduEnetPort1ChannelizedRslBelowThresholdClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.31			The condition has cleared. RSL is now above its minimum threshold.
NTF hzOduEnetPort1ChannelizedRslBelowThresholdV1Trap	1.3.6.1.4.1.7262.2.2.9.0.30			The RSL has been detected below its minimum threshold.
hzOduEnetPort1Config	1.3.6.1.4.1.7262.2.2.4.1.2
STR hzOduEnetPort1Description	1.3.6.1.4.1.7262.2.2.4.1.1	DisplayString	read-only	Describes the functionality of the port1
CTR hzOduEnetPort1DroppedEnetFramesThresholdCount	1.3.6.1.4.1.7262.2.2.8.3.1.2	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
INT hzOduEnetPort1DroppedEnetFramesThresholdExceeded	1.3.6.1.4.1.7262.2.2.8.3.1.1	INTEGER	read-only	The threshold for number of frames dropped has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.
STR hzOduEnetPort1DroppedEnetFramesThresholdParameters	1.3.6.1.4.1.7262.2.2.4.1.2.9	DisplayString	read-write	A read-write string: The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of frames that are dropped, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.
NTF hzOduEnetPort1DroppedFramesThresholdExceededClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.15			The condition has cleared.The ethernet dropped frames threshold is now below its threshold value.
NTF hzOduEnetPort1DroppedFramesThresholdExceededV1Trap	1.3.6.1.4.1.7262.2.2.9.0.14			The ethernet dropped frames threshold has been detected above its threshold value.
INT hzOduEnetPort1DroppedFramesThresholdExceedTrap	1.3.6.1.4.1.7262.2.2.9.12	INTEGER	read-write	Enables or disables the trap. This trap, if enabled, will be sent when the dropped ethernet frames threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
INT hzOduEnetPort1Duplex	1.3.6.1.4.1.7262.2.2.4.1.2.3	INTEGER	read-only	Configure the port1 interface duplex.
INT hzOduEnetPort1DuplexStatus	1.3.6.1.4.1.7262.2.2.4.1.3.4	INTEGER	read-only	Indicates the port1 interface duplex status.
INT hzOduEnetPort1EgressDataRate	1.3.6.1.4.1.7262.2.2.4.1.4.9	INTEGER	read-only	The data rate going out of the ethernet for port1. The data rate you see is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbs.
INT hzOduEnetPort1EthernetLinkDown	1.3.6.1.4.1.7262.2.2.8.3.1.9	INTEGER	read-only	Indicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.
CTR hzOduEnetPort1EthernetLinkDownActivatedCount	1.3.6.1.4.1.7262.2.2.8.3.1.10	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
CTR hzOduEnetPort1FramesInQueue1	1.3.6.1.4.1.7262.2.2.4.1.4.10	Counter	read-only	The current count of port1 frames passed through queue 1.
CTR hzOduEnetPort1FramesInQueue1Discarded	1.3.6.1.4.1.7262.2.2.4.1.4.14	Counter	read-only	The current count of NIC frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space.
CTR hzOduEnetPort1FramesInQueue2	1.3.6.1.4.1.7262.2.2.4.1.4.11	Counter	read-only	The current count of port1 frames passed through queue 2.
CTR hzOduEnetPort1FramesInQueue2Discarded	1.3.6.1.4.1.7262.2.2.4.1.4.15	Counter	read-only	The current count of port1 frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space.
CTR hzOduEnetPort1FramesInQueue3	1.3.6.1.4.1.7262.2.2.4.1.4.12	Counter	read-only	The current count of NIC frames passed through queue 3.
CTR hzOduEnetPort1FramesInQueue3Discarded	1.3.6.1.4.1.7262.2.2.4.1.4.16	Counter	read-only	The current count of port1 frames received in queue 3 that were discarded, but due to an error. One possible reason is lack of buffer space.
CTR hzOduEnetPort1FramesInQueue4	1.3.6.1.4.1.7262.2.2.4.1.4.13	Counter	read-only	The current count of NIC frames passed through queue 4.
CTR hzOduEnetPort1FramesInQueue4Discarded	1.3.6.1.4.1.7262.2.2.4.1.4.17	Counter	read-only	The current count of port1 frames received in queue 4 that were discarded, but due to an error. One possible reason is lack of buffer space.
INT hzOduEnetPort1IngressDataRate	1.3.6.1.4.1.7262.2.2.4.1.4.8	INTEGER	read-only	The data rate coming into the ethernet for port1. The data rate you see is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbs
INT hzOduEnetPort1LinkStatus	1.3.6.1.4.1.7262.2.2.4.1.3.1	INTEGER	read-only	Indicates the port1 link status.
INT hzOduEnetPort1MaxFrameSize	1.3.6.1.4.1.7262.2.2.4.1.2.8	INTEGER	read-write	For port1 the default maximum frame size is 1600 bytes. The settable maximum frame size must be a multiple of 128. If the chosen maximum frame size is not a multiple of 128, its closest number which is a multiple of 128 is actually used. The settable lowest maximum frame size is 1664, and the settable highest maximum frame size is 9600. If the chosen maximum frame size is out of this range, the default maximum frame size of 1600 is used.
INT hzOduEnetPort1Media	1.3.6.1.4.1.7262.2.2.4.1.2.4	INTEGER	read-write	Configure the port1 interface media.
INT hzOduEnetPort1MediaStatus	1.3.6.1.4.1.7262.2.2.4.1.3.5	INTEGER	read-only	Indicates the port1 interface media status.
INT hzOduEnetPort1OpticalTransceiverState	1.3.6.1.4.1.7262.2.2.4.1.2.6	INTEGER	read-write	When it is on, optical transmitter for port1 is enabled. Otherwise optical transmitter is disabled.
INT hzOduEnetPort1PauseFrameEnable	1.3.6.1.4.1.7262.2.2.4.1.2.7	INTEGER	read-write	When PAUSE is enabled, port1 pause frames can be generated by the system and the pause frames will flow toward the link partner on the network. When PAUSE is not enabled, no pause frames will be generated by the system.
INT hzOduEnetPort1RlsMismatch	1.3.6.1.4.1.7262.2.2.8.3.1.5	INTEGER	read-only	RLS configurations on the pair of systems are mismatched.
NTF hzOduEnetPort1RlsMismatchClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.19			RLS mismatch cleared
CTR hzOduEnetPort1RlsMismatchCount	1.3.6.1.4.1.7262.2.2.8.3.1.6	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
INT hzOduEnetPort1RlsMismatchTrap	1.3.6.1.4.1.7262.2.2.9.14	INTEGER	read-write	Enables or disables the trap.
NTF hzOduEnetPort1RlsMismatchV1Trap	1.3.6.1.4.1.7262.2.2.9.0.18			RLS mismatch
INT hzOduEnetPort1RLSShutdownActivated	1.3.6.1.4.1.7262.2.2.8.3.1.7	INTEGER	read-only	RLS shutdown is activated.
NTF hzOduEnetPort1RlsShutdownActivatedClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.21			RLS shutdown is not activated
CTR hzOduEnetPort1RLSShutdownActivatedCount	1.3.6.1.4.1.7262.2.2.8.3.1.8	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
INT hzOduEnetPort1RLSShutdownActivatedTrap	1.3.6.1.4.1.7262.2.2.9.15	INTEGER	read-write	Enables or disables the trap.
NTF hzOduEnetPort1RlsShutdownActivatedv1Trap	1.3.6.1.4.1.7262.2.2.9.0.20			RLS shutdown is activated
CTR hzOduEnetPort1RxBytes	1.3.6.1.4.1.7262.2.2.4.1.4.4	Counter	read-only	The current count of port1 bytes received.
CTR hzOduEnetPort1RxFrames	1.3.6.1.4.1.7262.2.2.4.1.4.3	Counter	read-only	The current count of port1 frames received.
CTR hzOduEnetPort1RxFramesCRCError	1.3.6.1.4.1.7262.2.2.4.1.4.6	Counter	read-only	The current count of CRC error frames received for port1.
CTR hzOduEnetPort1RxFramesInError	1.3.6.1.4.1.7262.2.2.4.1.4.5	Counter	read-only	The current count of port1 frames received in error.
INT hzOduEnetPort1Speed	1.3.6.1.4.1.7262.2.2.4.1.2.2	INTEGER	read-write	Configure the port1 interface speed .
INT hzOduEnetPort1SpeedStatus	1.3.6.1.4.1.7262.2.2.4.1.3.3	INTEGER	read-only	Indicates the port1 interface speed status.
hzOduEnetPort1Stats	1.3.6.1.4.1.7262.2.2.4.1.4
hzOduEnetPort1Status	1.3.6.1.4.1.7262.2.2.4.1.3
CTR hzOduEnetPort1TxBytes	1.3.6.1.4.1.7262.2.2.4.1.4.2	Counter	read-only	The current count of port1 bytes sent.
CTR hzOduEnetPort1TxFrames	1.3.6.1.4.1.7262.2.2.4.1.4.1	Counter	read-only	The current count of port1 frames sent.
hzOduEnetPort2	1.3.6.1.4.1.7262.2.2.4.2
INT hzOduEnetPort2AdminState	1.3.6.1.4.1.7262.2.2.4.2.2.4	INTEGER	read-only	Configure the port2 shutdown media.
hzOduEnetPort2Alarms	1.3.6.1.4.1.7262.2.2.8.3.2
INT hzOduEnetPort2AutoNegotiation	1.3.6.1.4.1.7262.2.2.4.2.2.1	INTEGER	read-write	port1 Turns auto-negotiation on or off. Turning off results in the interface defaulting to 100BaseT, Full Duplex.
INT hzOduEnetPort2AutoNegotiationStatus	1.3.6.1.4.1.7262.2.2.4.2.3.2	INTEGER	read-only	Indicates the Port2 AutoNegotiation status.
hzOduEnetPort2Config	1.3.6.1.4.1.7262.2.2.4.2.2
STR hzOduEnetPort2Description	1.3.6.1.4.1.7262.2.2.4.2.1	DisplayString	read-only	Describes the functionality of the port2
INT hzOduEnetPort2Duplex	1.3.6.1.4.1.7262.2.2.4.2.2.3	INTEGER	read-only	Configure the port1 interface duplex.
INT hzOduEnetPort2DuplexStatus	1.3.6.1.4.1.7262.2.2.4.2.3.4	INTEGER	read-only	Indicates the Port2 interface duplex status.
INT hzOduEnetPort2EthernetLinkDown	1.3.6.1.4.1.7262.2.2.8.3.2.1	INTEGER	read-only	Indicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.
CTR hzOduEnetPort2EthernetLinkDownActivatedCount	1.3.6.1.4.1.7262.2.2.8.3.2.2	Counter	read-only	Indicates the approximate time, in seconds, that this alarm has been in the active state
INT hzOduEnetPort2LinkStatus	1.3.6.1.4.1.7262.2.2.4.2.3.1	INTEGER	read-only	Indicates the Port2 link status.
INT hzOduEnetPort2MediaStatus	1.3.6.1.4.1.7262.2.2.4.2.3.5	INTEGER	read-only	Indicates the port1 interface media status.
CTR hzOduEnetPort2RxBytes	1.3.6.1.4.1.7262.2.2.4.2.4.4	Counter	read-only	The current count of Port2 bytes received.
CTR hzOduEnetPort2RxFrames	1.3.6.1.4.1.7262.2.2.4.2.4.3	Counter	read-only	The current count of Port2 frames received.
CTR hzOduEnetPort2RxFramesCrcError	1.3.6.1.4.1.7262.2.2.4.2.4.6	Counter	read-only	The current count of CRC error frames received for Port2.
CTR hzOduEnetPort2RxFramesInError	1.3.6.1.4.1.7262.2.2.4.2.4.5	Counter	read-only	The current count of Port2 frames received in error.
INT hzOduEnetPort2Speed	1.3.6.1.4.1.7262.2.2.4.2.2.2	INTEGER	read-write	Configure the port1 interface speed .
INT hzOduEnetPort2SpeedStatus	1.3.6.1.4.1.7262.2.2.4.2.3.3	INTEGER	read-only	Indicates the Port2 interface speed status.
hzOduEnetPort2Stats	1.3.6.1.4.1.7262.2.2.4.2.4
hzOduEnetPort2Status	1.3.6.1.4.1.7262.2.2.4.2.3
CTR hzOduEnetPort2TxBytes	1.3.6.1.4.1.7262.2.2.4.2.4.2	Counter	read-only	The current count of Port2 bytes sent.
CTR hzOduEnetPort2TxFrames	1.3.6.1.4.1.7262.2.2.4.2.4.1	Counter	read-only	The current count of Port2 frames sent.
INT hzOduEventLogEnable	1.3.6.1.4.1.7262.2.2.16.1	INTEGER	read-write	Indicates whether event log is enabled.
INT hzOduExplicitAuthenticationFailure	1.3.6.1.4.1.7262.2.2.8.2.1	INTEGER	read-only	Authentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.
NTF hzOduExplicitAuthenticationFailureClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.4			The condition has cleared. The peer node is now authenticated.
CTR hzOduExplicitAuthenticationFailureCount	1.3.6.1.4.1.7262.2.2.8.2.2	Counter	read-only	Indicates the number of times explicit authentication has failed.
INT hzOduExplicitAuthenticationFailureTrap	1.3.6.1.4.1.7262.2.2.9.6	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduExplicitAuthenticationFailureV1Trap	1.3.6.1.4.1.7262.2.2.9.0.3			Authentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.
INT hzOduFreqGroupSelected	1.3.6.1.4.1.7262.2.2.6.2	INTEGER	read-write	The frequency group selected for the system. The frequency subbands are divided into frequency groups txHigh and txLow. An horizon system must have one node configured to txLow and the other node configure to txHigh
hzOduFrequencies	1.3.6.1.4.1.7262.2.2.6
INT hzOduFrequencyFileInvalid	1.3.6.1.4.1.7262.2.2.8.2.11	INTEGER	read-only	Executing frequency file is valid or not
CTR hzOduFrequencyFileInvalidCount	1.3.6.1.4.1.7262.2.2.8.2.12	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduFrequencyFileInvalidTrap	1.3.6.1.4.1.7262.2.2.9.11	INTEGER	read-write	Enables or disables the trap.
NTF hzOduFrequencyFileInvalidV1Trap	1.3.6.1.4.1.7262.2.2.9.0.13			When the executing frequency file is invalid, this trap is generated.
STR hzOduFrequencyFileVersionNo	1.3.6.1.4.1.7262.2.2.1.3.2.3	DisplayString	read-only	The version number of the FrequencyFile.
NTF hzOduHsbActiveOnPrimaryClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.61			Hsb active on primary is cleared.
INT hzOduHsbActiveOnPrimaryTrap	1.3.6.1.4.1.7262.2.2.9.36	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduHsbActiveOnPrimaryV1Trap	1.3.6.1.4.1.7262.2.2.9.0.60			Hsb active on primary.
INT hzOduHsbActiveOnSecondary	1.3.6.1.4.1.7262.2.2.8.2.19	INTEGER	read-only	Indicates the hsb active link is on secondary.
NTF hzOduHsbActiveOnSecondaryClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.55			Hsb active on secondary is cleared.
CTR hzOduHsbActiveOnSecondaryCount	1.3.6.1.4.1.7262.2.2.8.2.20	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduHsbActiveOnSecondaryTrap	1.3.6.1.4.1.7262.2.2.9.33	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduHsbActiveOnSecondaryV1Trap	1.3.6.1.4.1.7262.2.2.9.0.54			Hsb active on secondary.
INT hzOduHsbCrossLinkActive	1.3.6.1.4.1.7262.2.2.8.2.23	INTEGER	read-only	Indicates the hsb cross link is active.
CTR hzOduHsbCrossLinkActiveCount	1.3.6.1.4.1.7262.2.2.8.2.24	Counter	read-only	Indicates the time (in secs) since this alarm exist.
NTF hzOduHsbCrossLinkClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.59			Hsb cross link is cleared.
INT hzOduHsbCrossLinkTrap	1.3.6.1.4.1.7262.2.2.9.35	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduHsbCrossLinkV1Trap	1.3.6.1.4.1.7262.2.2.9.0.58			Hsb cross link by user.
INT hzOduHsbOverrideByUser	1.3.6.1.4.1.7262.2.2.8.2.21	INTEGER	read-only	Indicates the hsb mode is overrided by user.
NTF hzOduHsbOverrideByUserClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.57			Hsb active on secondary is cleared.
CTR hzOduHsbOverrideByUserCount	1.3.6.1.4.1.7262.2.2.8.2.22	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduHsbOverrideByUserTrap	1.3.6.1.4.1.7262.2.2.9.34	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduHsbOverrideByUserV1Trap	1.3.6.1.4.1.7262.2.2.9.0.56			Hsb override by user.
hzOduHttp	1.3.6.1.4.1.7262.2.2.12
INT hzOduHttpEnable	1.3.6.1.4.1.7262.2.2.12.1	INTEGER	read-write	Indicates whether HTTP is enabled.
hzOduHttpSecure	1.3.6.1.4.1.7262.2.2.12.2
INT hzOduHttpSecureAccessForAdminUsers	1.3.6.1.4.1.7262.2.2.12.2.2	INTEGER	read-write	the HTTPS access requirement for Admin user group.
INT hzOduHttpSecureAccessForNocUsers	1.3.6.1.4.1.7262.2.2.12.2.3	INTEGER	read-write	the HTTPS access requirement for Noc user group.
INT hzOduHttpSecureAccessForSuperUsers	1.3.6.1.4.1.7262.2.2.12.2.4	INTEGER	read-write	the HTTPS access requirement for Super user group.
STR hzOduHttpSecureCertificateStatus	1.3.6.1.4.1.7262.2.2.12.2.1	DisplayString	read-only	Returns the HTTPS certificate status
hzOduHwInventory	1.3.6.1.4.1.7262.2.2.1.3.1
INT hzOduHysterisisErredFramesPerMilliSecond	1.3.6.1.4.1.7262.2.2.14.1.4	INTEGER	read-write	The link will be automatically shut down when this number of erred modem frames threshold is exceeded during the time set in the hysterisisErredMilliSeconds object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system.
INT hzOduHysterisisErredMilliSeconds	1.3.6.1.4.1.7262.2.2.14.1.5	INTEGER	read-write	The time to determine a link that has excessive errors. The link will be automatically shut down when this number of milliseconds experiences the number of erred frames specified in the hysterisisErredFramesPerMilliSecond object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system.
INT hzOduHysterisisUnerredFramesPerMilliSecond	1.3.6.1.4.1.7262.2.2.14.1.6	INTEGER	read-write	The link will be automatically brought back up when the number of erred modem frames is less than this value ( only if automaticLinkReestablish is set to enabled). This threshold value cannot be crossed for the duration of time specified in the hysterisisUnerredMilliSeconds object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system.
INT hzOduHysterisisUnerredMilliSeconds	1.3.6.1.4.1.7262.2.2.14.1.7	INTEGER	read-write	The time block to use to determine if the link is error free enough to warrant it to automatically reestablish itself ( only if automaticLinkReestablish is set to enabled). The link will be brought back up automatically when this number of milliseconds experiences less the number of acceptable erred frames specified in the hysterisisUnerredFramesPerMilliSecond object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system.
STR hzOduIfAssemblylNo	1.3.6.1.4.1.7262.2.2.1.3.1.4	DisplayString	read-only	A textual string containing assembly no of the IF.
STR hzOduIfSerialNo	1.3.6.1.4.1.7262.2.2.1.3.1.3	DisplayString	read-only	A textual string containing Serial no of the IF.
hzOduInventory	1.3.6.1.4.1.7262.2.2.1.3
IP hzOduIpAddress	1.3.6.1.4.1.7262.2.2.3.3	IpAddress	read-only	The IP Address of the network interface card.
INT hzOduLinkDownTrap	1.3.6.1.4.1.7262.2.2.9.4	INTEGER	read-write	Specifies whether this trap is to be sent or not
INT hzOduLinkUpTrap	1.3.6.1.4.1.7262.2.2.9.5	INTEGER	read-write	Specifies whether this trap is to be sent or not
hzOduLogs	1.3.6.1.4.1.7262.2.2.16
STR hzOduMacAddress	1.3.6.1.4.1.7262.2.2.3.1	DisplayString	read-only	The MAC Address of the network interface card.
hzOduManagementSessions	1.3.6.1.4.1.7262.2.2.11
INT hzOduManualLinkReestablish	1.3.6.1.4.1.7262.2.2.14.1.3	INTEGER	read-write	This object is writeable ONLY if automaticLinkReestablish is set to disabled. The user explicitly brings the link back up by setting this object to enabled. The user explicitly brings the link down by setting this object to disabled. to bring the link back up
STR hzOduMibVersionNo	1.3.6.1.4.1.7262.2.2.1.3.2.4	DisplayString	read-only	The version number of the MIB.
hzOduModem1	1.3.6.1.4.1.7262.2.2.5.1.2
INT hzOduModem1AdminStatus	1.3.6.1.4.1.7262.2.2.5.1.2.1	INTEGER	read-only	The current admin state of the interface. Testing indicates that no operational packets can be passed.
hzOduModem1Alarms	1.3.6.1.4.1.7262.2.2.8.4.4
INT hzOduModem1ChannelizedRSL	1.3.6.1.4.1.7262.2.2.5.1.2.4	INTEGER	read-only	An estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value
STR hzOduModem1ChannelizedRslBelowThresholdParameters	1.3.6.1.4.1.7262.2.2.5.1.2.12	DisplayString	read-write	A read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the second is the time in seconds that the threshold must be exceeded. In this example the threshold -75 dBm and the time is set to 10 seconds. The single quote marks i.e. ' ' are not used in the command.
INT hzOduModem1ChannelizedRslBelowThresholdTrap	1.3.6.1.4.1.7262.2.2.9.20	INTEGER	read-write	Enables or disables the trap. This trap, if enabled, will be sent when the radio receive signal level threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
INT hzOduModem1ChannelizedRSLUnsignedInt	1.3.6.1.4.1.7262.2.2.5.1.2.14	INTEGER	read-only	An estimate of the modem's channelized RSL in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm. Object provided mainly to accomodate plotting of negative RSL values which is not supported in some EMS (Ex: CastleRock). Please use 'hzOduModem1ChannelizedRSL' object if your EMS supports plotting of -ve integer.
INT hzOduModem1CurrentRxSpeed	1.3.6.1.4.1.7262.2.2.5.1.2.6	INTEGER	read-only	An estimate of the modem's current Rx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps
INT hzOduModem1CurrentTxSpeed	1.3.6.1.4.1.7262.2.2.5.1.2.7	INTEGER	read-only	An estimate of the modem's current Tx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps
INT hzOduModem1EbToNoiseRatio	1.3.6.1.4.1.7262.2.2.5.1.2.9	INTEGER	read-only	The ratio of the modem Estimated Energy per information bit to Noise power spectral density. Divide the value by 10 to get the actual EbToNoiseRatio
INT hzOduModem1EqualizerStress	1.3.6.1.4.1.7262.2.2.5.1.2.10	INTEGER	read-only	Indicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working.
INT hzOduModem1EqualizerStressExceedThreshold	1.3.6.1.4.1.7262.2.2.8.4.4.7	INTEGER	read-only	Equalizer Stress measured within the demodulator exceeds the threshold value.
NTF hzOduModem1EqualizerStressExceedThresholdClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.29			Equalizer Stress measured within the demodulator is within the threshold value.
INT hzOduModem1EqualizerStressExceedThresholdTrap	1.3.6.1.4.1.7262.2.2.9.19	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1EqualizerStressExceedThresholdV1Trap	1.3.6.1.4.1.7262.2.2.9.0.28			Equalizer Stress measured within the demodulator exceeds the threshold value.
CTR hzOduModem1EquilizerStressExceedThresholdCount	1.3.6.1.4.1.7262.2.2.8.4.4.8	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
INT hzOduModem1HardwareFault	1.3.6.1.4.1.7262.2.2.8.4.4.9	INTEGER	read-only
NTF hzOduModem1HardwareFaultClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.33			Power supply circuitry is in good condition.
CTR hzOduModem1HardwareFaultCount	1.3.6.1.4.1.7262.2.2.8.4.4.10	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
INT hzOduModem1HardwareFaultTrap	1.3.6.1.4.1.7262.2.2.9.21	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1HardwareFaultV1Trap	1.3.6.1.4.1.7262.2.2.9.0.32			Power supply circuitry failed. Should be sent for diagnosis.
TIK hzOduModem1LastChange	1.3.6.1.4.1.7262.2.2.5.1.2.13	TimeTicks	read-only	The value of sysUpTime at the time the modem entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
INT hzOduModem1ModulationType	1.3.6.1.4.1.7262.2.2.5.1.2.5	INTEGER	read-only	The modulation type of the modem, distinguished according to the physical/link protocol.
INT hzOduModem1OperStatus	1.3.6.1.4.1.7262.2.2.5.1.2.2	INTEGER	read-only	The current operational state of the interface. Testing indicates that no operational packets can be passed.
INT hzOduModem1ProgrammingError	1.3.6.1.4.1.7262.2.2.8.4.4.11	INTEGER	read-only	Encountered some problem while programming the modem.
NTF hzOduModem1ProgrammingErrorClearedrV1Trap	1.3.6.1.4.1.7262.2.2.9.0.35			Problem encountered while programming modem is gone.
CTR hzOduModem1ProgrammingErrorCount	1.3.6.1.4.1.7262.2.2.8.4.4.12	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
INT hzOduModem1ProgrammingErrorTrap	1.3.6.1.4.1.7262.2.2.9.22	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1ProgrammingErrorV1Trap	1.3.6.1.4.1.7262.2.2.9.0.34			Encountered problem while programming modem.
INT hzOduModem1Reset	1.3.6.1.4.1.7262.2.2.5.1.2.3	INTEGER	write-only	Writing 1 to this object causes the modem card to be reset. All other values are not recognized. This variable always reads back as 0. mdmOperStatus should be polled by the user after this object is written to, to verify that the modem card has been reset. Not applicable in this release
CTR hzOduModem1RxBlocksError	1.3.6.1.4.1.7262.2.2.5.1.2.15.7	Counter	read-only	The current count of Modem blocks received in error.
CTR hzOduModem1RxBlocksOK	1.3.6.1.4.1.7262.2.2.5.1.2.15.6	Counter	read-only	The current count of Modem blocks received.
CTR hzOduModem1RxFramesError	1.3.6.1.4.1.7262.2.2.5.1.2.15.3	Counter	read-only	The current count of Modem frames received in error.
CTR hzOduModem1RxFramesOK	1.3.6.1.4.1.7262.2.2.5.1.2.15.2	Counter	read-only	The current count of Modem frames received.
CTR hzOduModem1RxFramesQueueDiscarded	1.3.6.1.4.1.7262.2.2.5.1.2.15.4	Counter	read-only	The current count of Modem frames in the queue that were discarded.
INT hzOduModem1RxLossOfSignal	1.3.6.1.4.1.7262.2.2.8.4.4.1	INTEGER	read-only	Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.
CTR hzOduModem1RxLossOfSignalCount	1.3.6.1.4.1.7262.2.2.8.4.4.2	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
NTF hzOduModem1RxLossOfSignalLockClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.23			The condition has cleared. The demodulator is synchronized.
INT hzOduModem1RxLossOfSignalLockTrap	1.3.6.1.4.1.7262.2.2.9.16	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1RxLossOfSignalLockV1Trap	1.3.6.1.4.1.7262.2.2.9.0.22			Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.
INT hzOduModem1SNR	1.3.6.1.4.1.7262.2.2.5.1.2.8	INTEGER	read-only	SNR value in dB. Divide the value by 10 to get the actual SNR.
INT hzOduModem1SnrBelowThreshold	1.3.6.1.4.1.7262.2.2.8.4.4.5	INTEGER	read-only	The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the horizon nodes.
NTF hzOduModem1SnrBelowThresholdClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.27			SNR performance back to normal.
CTR hzOduModem1SnrBelowThresholdCount	1.3.6.1.4.1.7262.2.2.8.4.4.6	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
INT hzOduModem1SnrBelowThresholdTrap	1.3.6.1.4.1.7262.2.2.9.18	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1SnrBelowThresholdV1Trap	1.3.6.1.4.1.7262.2.2.9.0.26			The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the horizon nodes.
STR hzOduModem1SNRThresholdParameters	1.3.6.1.4.1.7262.2.2.5.1.2.11	DisplayString	read-write	A read-write string
hzOduModem1Statistics	1.3.6.1.4.1.7262.2.2.5.1.2.15
CTR hzOduModem1TxBlocks	1.3.6.1.4.1.7262.2.2.5.1.2.15.5	Counter	read-only	The current count of Modem blocks transmitted.
CTR hzOduModem1TxFrames	1.3.6.1.4.1.7262.2.2.5.1.2.15.1	Counter	read-only	The current count of Modem frames sent.
INT hzOduModem1TxLossOfSync	1.3.6.1.4.1.7262.2.2.8.4.4.3	INTEGER	read-only	Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon nodes.
NTF hzOduModem1TxLossOfSyncClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.25			Tx Loss of sync bytes cleared.
CTR hzOduModem1TxLossOfSyncCount	1.3.6.1.4.1.7262.2.2.8.4.4.4	Counter	read-only	Indicates the approximate number of seconds that this alarm has been active.
INT hzOduModem1TxLossOfSyncTrap	1.3.6.1.4.1.7262.2.2.9.17	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduModem1TxLossOfSyncV1Trap	1.3.6.1.4.1.7262.2.2.9.0.24			Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon nodes.
STR hzOduModemOmniVersionNo	1.3.6.1.4.1.7262.2.2.1.3.2.2	DisplayString	read-only	The version number of the Modem FPGA.
STR hzOduNccAssemblylNo	1.3.6.1.4.1.7262.2.2.1.3.1.8	DisplayString	read-only	A textual string containing assembly no of the NCC.
STR hzOduNccSerialNo	1.3.6.1.4.1.7262.2.2.1.3.1.7	DisplayString	read-only	A textual string containing Serial no of the NCC.
hzOduNetworkInterface	1.3.6.1.4.1.7262.2.2.4
hzOduNetworkInterfaceAlarms	1.3.6.1.4.1.7262.2.2.8.3
hzOduNetworkManagement	1.3.6.1.4.1.7262.2.2.3
INT hzOduNetworkManagementInterface	1.3.6.1.4.1.7262.2.2.3.2	INTEGER	read-only	Describes the network management interface connection options.
INT hzOduOperStatus	1.3.6.1.4.1.7262.2.2.1.1.3	INTEGER	read-only	The current operational state of the system. Testing indicates that no operational packets can be passed.
INT hzOduPartnerConfigurationMismatch	1.3.6.1.4.1.7262.2.2.8.2.17	INTEGER	read-only	Indicates partner configuration mismatches.
NTF hzOduPartnerConfigurationMismatchClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.53			Hsb partner configuration mismatch is cleared.
CTR hzOduPartnerConfigurationMismatchCount	1.3.6.1.4.1.7262.2.2.8.2.18	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduPartnerConfigurationMismatchTrap	1.3.6.1.4.1.7262.2.2.9.32	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduPartnerConfigurationMismatchV1Trap	1.3.6.1.4.1.7262.2.2.9.0.52			Hsb partner configuration mismatch.
INT hzOduPartnerRedundancyModeMismatch	1.3.6.1.4.1.7262.2.2.8.2.15	INTEGER	read-only	Indicates partner redundancy mode mismatches.
NTF hzOduPartnerRedundancyModeMismatchClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.51			Hsb partner redundancy mode mismatch is cleared.
CTR hzOduPartnerRedundancyModeMismatchCount	1.3.6.1.4.1.7262.2.2.8.2.16	Counter	read-only	Indicates the time (in secs) since this alarm exist.
INT hzOduPartnerRedundancyModeMismatchTrap	1.3.6.1.4.1.7262.2.2.9.31	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduPartnerRedundancyModeMismatchV1Trap	1.3.6.1.4.1.7262.2.2.9.0.50			Hsb partner redundancy mode mismatch.
INT hzOduPeerAuthenticationStatus	1.3.6.1.4.1.7262.2.2.2.5	INTEGER	read-only	Specifies the current authentication status of the system. Authenticated means authentication is on and the system has been authenticated, notAuthenticated means authentication is off or the system has not communicated yet with the other node, explicit authentication failure means authentication is on and authentication has failed
STR hzOduPeerDetectedSerialNumber	1.3.6.1.4.1.7262.2.2.2.2	DisplayString	read-only	The serial number of the peer node that the system is presently communicating with. This is only used when authentication is set to unique.
IP hzOduPeerIpAddress	1.3.6.1.4.1.7262.2.2.1.6.2	IpAddress	read-only	The IP Address of the peer network interface card.
STR hzOduPeerMacAddress	1.3.6.1.4.1.7262.2.2.1.6.1	DisplayString	read-only	The MAC Address of the peer network interface card.
IP hzOduPeerSubnetMask	1.3.6.1.4.1.7262.2.2.1.6.3	IpAddress	read-only	The subnet mask for the peer network interface card.
hzOduPeerSysInfo	1.3.6.1.4.1.7262.2.2.1.6
INT hzOduPerfmLogEnable	1.3.6.1.4.1.7262.2.2.16.2	INTEGER	read-write	Indicates whether performance log is enabled.
STR hzOduPerfmLogInterval	1.3.6.1.4.1.7262.2.2.16.3	DisplayString	read-write	Performance statistics are logged periodically by this interval.
INT hzOduPrimaryActualEstablishMonitorTime	1.3.6.1.4.1.7262.2.2.14.2.9.15	INTEGER	read-only	Actual Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, it's a multiple of the establish sample period required to observe the FER
INT hzOduPrimaryActualShutdownMonitorTime	1.3.6.1.4.1.7262.2.2.14.2.9.17	INTEGER	read-only	Actual Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, it's a multiple of the shutdown sample period required to observe the FER
INT hzOduPrimaryAutomaticLinkReestablish	1.3.6.1.4.1.7262.2.2.14.2.3	INTEGER	read-write	If this feature is enabled, the link will be automatically reestablished If this feature is disabled, the user must explicitly use the manualReestablish object to bring the link back up
STR hzOduPrimaryDegradeMonitorState	1.3.6.1.4.1.7262.2.2.14.2.9.4	DisplayString	read-only	Degrade Monitor State. If the state is activated, that means the RLS Degrade Monitor is asserting the link down. If the state is OK, that means the RLS Degrade Monitor is asserting the link up.
INT hzOduPrimaryEstablishErredFrameThreshold	1.3.6.1.4.1.7262.2.2.14.2.6.1	INTEGER	read-write	Maximum erred blocks, per sample, allowed for link establishment.
INT hzOduPrimaryEstablishNumberOfSamples	1.3.6.1.4.1.7262.2.2.14.2.6.3	INTEGER	read-write	Minimum number of consecutive good samples required before link is established.
INT hzOduPrimaryEstablishSamplePeriod	1.3.6.1.4.1.7262.2.2.14.2.6.5	INTEGER	read-write	Period of Time, in milliseconds, for monitoring Establish Erred Frame Threshold.
INT hzOduPrimaryFaultSamplePeriod	1.3.6.1.4.1.7262.2.2.14.2.7.1	INTEGER	read-write	The period of time, in milliseconds, for which the rlsFaultThreshold is applied.
INT hzOduPrimaryFaultThreshold	1.3.6.1.4.1.7262.2.2.14.2.7.2	INTEGER	read-write	The percentage of the rlsFaultSamplePeriodMilliSeconds period which must be degraded before the link is set to the 'impaired' state.
hzOduPrimaryHardFaultMonitor	1.3.6.1.4.1.7262.2.2.14.2.7
STR hzOduPrimaryHardFaultMonitorState	1.3.6.1.4.1.7262.2.2.14.2.9.5	DisplayString	read-only	Hard Fault Monitor State. If the state is activated, that means the Hard Fault Monitor is asserting the link down. If the state is OK, that means the RLS Hard Fault Monitor is asserting the link up.
STR hzOduPrimaryMakeRslThresholdState	1.3.6.1.4.1.7262.2.2.14.2.9.6	DisplayString	read-only	Make RSL Threshold State. If the state is not met, that means the RLS signal level is below the threshold value. If the state is OK, that means the RLS signal level is above the threshold value.
INT hzOduPrimaryManualLinkReestablish	1.3.6.1.4.1.7262.2.2.14.2.4	INTEGER	read-write	This object is writeable ONLY if automaticLinkReestablish is set to disabled. The user explicitly brings the link back up by setting this object to enabled. The user explicitly brings the link down by setting this object to disabled. to bring the link back up
STR hzOduPrimaryMinimumAchievableEstablishFer	1.3.6.1.4.1.7262.2.2.14.2.9.11	DisplayString	read-only	Minimum achievable Frame Error Ratio required for the link to be restored to service. An example value being '1.0E-7'.
STR hzOduPrimaryMinimumAchievableShutdownFer	1.3.6.1.4.1.7262.2.2.14.2.9.13	DisplayString	read-only	Minimum achievable Frame Error Ratio required for the link to remain in-service. An example value being '1.0E-7'.
STR hzOduPrimaryNetworkInterfaceState	1.3.6.1.4.1.7262.2.2.14.2.9.9	DisplayString	read-only	Network Interface State. If the state is down, that means the network interface (Ethernet/PHY) is not operational(disconnected, not configured). If the state is up, that means the network interface (Ethernet/PHY) is operational.
STR hzOduPrimaryPeerRslState	1.3.6.1.4.1.7262.2.2.14.2.9.7	DisplayString	read-only	Peer RSL State. If the state is activated, that means the peer has activated RLS. If the state is OK, that means the Peer hasn't activated RLS.
INT hzOduPrimaryQuickShutdownSamplePeriod	1.3.6.1.4.1.7262.2.2.14.2.6.7	INTEGER	read-write	Minimum number of milliseconds required to classify samples as erred.
STR hzOduPrimaryRadioInterfaceState	1.3.6.1.4.1.7262.2.2.14.2.9.8	DisplayString	read-only	Radio Interface State. If the state is down, that means The radio interface is not operational(muted,disconnected, not configured). If the state is up, that means the radio interface is operational.
hzOduPrimaryReceiveSignalLevelMonitor	1.3.6.1.4.1.7262.2.2.14.2.8
INT hzOduPrimaryRlsEnable	1.3.6.1.4.1.7262.2.2.14.2.1	INTEGER	read-write	The Rapid Link Shutdown feature: enabled or disabled. Changing this option requires a system reset.
INT hzOduPrimaryRlsHardFaultMonitor	1.3.6.1.4.1.7262.2.2.14.2.2	INTEGER	read-write	This object has changed - Enable the rlsHardFaultMonitor for rapid detection of severely degrade link. When disabled the only the RLS Link Degrade Monitor is used.
INT hzOduPrimaryRlsMakeRslMonitorPeriod	1.3.6.1.4.1.7262.2.2.14.2.8.2	INTEGER	read-write	The desired period, in seconds. When Link is inactive and if RSL is higher than the desired threshold for this period, the link will become active.
STR hzOduPrimaryRlsMakeRslMonitorRslValue	1.3.6.1.4.1.7262.2.2.14.2.8.1	DisplayString	read-write	The RSL threshold, in dBm. When Link is inactive and if RSL is higher than this threshold for a desired period, the link will become active.
STR hzOduPrimaryRlsMismatchState	1.3.6.1.4.1.7262.2.2.14.2.9.3	DisplayString	read-only	RLS Mismatch State. If the state is activated, that means RLS configuration is mismatched with peer. If the state is OK, that means RLS configuration is matched with peer.
STR hzOduPrimaryRlsOption	1.3.6.1.4.1.7262.2.2.14.2.9.1	DisplayString	read-only	RLS Option. On Basic: RLS enabled with base degrade monitoring; On Advanced: RLS enabled with hard fault monitoring; Off: Entire RLS feature disabled.
STR hzOduPrimaryRlsState	1.3.6.1.4.1.7262.2.2.14.2.9.2	DisplayString	read-only	Rapid Link Shutdown State. If the state is activated, that means link is down; If the state is inactivated, that means that link is up.
hzOduPrimaryRlsStatus	1.3.6.1.4.1.7262.2.2.14.2.9
INT hzOduPrimaryShutdownErredFrameThreshold	1.3.6.1.4.1.7262.2.2.14.2.6.2	INTEGER	read-write	Minimum erred blocks, per sample, allowed before link shutdown.
INT hzOduPrimaryShutdownNumberOfSamples	1.3.6.1.4.1.7262.2.2.14.2.6.4	INTEGER	read-write	Minimum number of consecutive erred samples before link is shutdown.
INT hzOduPrimaryShutdownSamplePeriod	1.3.6.1.4.1.7262.2.2.14.2.6.6	INTEGER	read-write	Period of Time, in milliseconds, for monitoring Shutdown Erred Frame Threshold.
hzOduPrimarySoftFaultMonitor	1.3.6.1.4.1.7262.2.2.14.2.6
STR hzOduPrimaryUserConfiguredEstablishFer	1.3.6.1.4.1.7262.2.2.14.2.9.10	DisplayString	read-only	User Configured Establish Frame Error Ratio required for the link to be restored to service, set by the user. An example value being '1.0E-7'.
INT hzOduPrimaryUserConfiguredEstablishMonitorTime	1.3.6.1.4.1.7262.2.2.14.2.9.14	INTEGER	read-only	User Configured Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, set by user
STR hzOduPrimaryUserConfiguredShutdownFer	1.3.6.1.4.1.7262.2.2.14.2.9.12	DisplayString	read-only	User Configured Shutdown Frame Error Ratio required for the link to remain in-service, set by the user. An example value being '1.0E-7'.
INT hzOduPrimaryUserConfiguredShutdownMonitorTime	1.3.6.1.4.1.7262.2.2.14.2.9.16	INTEGER	read-only	User Configured Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, set by user.
hzOduProgrammedFrequency	1.3.6.1.4.1.7262.2.2.6.5
STR hzOduProgrammedFrequencyChannel	1.3.6.1.4.1.7262.2.2.6.5.1	DisplayString	read-only	The channel that has been programmed into the system.
INT hzOduProgrammedFrequencyRxRf	1.3.6.1.4.1.7262.2.2.6.5.3	INTEGER	read-only	The RF RX frequency in MHz.
INT hzOduProgrammedFrequencyTxRf	1.3.6.1.4.1.7262.2.2.6.5.2	INTEGER	read-only	The programmed RF TX frequency in MHz.
hzOduQos	1.3.6.1.4.1.7262.2.2.13
INT hzOduQosEnable	1.3.6.1.4.1.7262.2.2.13.1	INTEGER	read-write	Indicates whether QOS is enabled.
hzOduRadio1	1.3.6.1.4.1.7262.2.2.5.1.3
hzOduRadio1Alarms	1.3.6.1.4.1.7262.2.2.8.4.5
INT hzOduRadio1DrainCurrentOutOfLimit	1.3.6.1.4.1.7262.2.2.8.4.5.7	INTEGER	read-only	Radio current1 out of limits.
NTF hzOduRadio1DrainCurrentOutOfLimitClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.43			Radio current out of limits cleared.
CTR hzOduRadio1DrainCurrentOutOfLimitCount	1.3.6.1.4.1.7262.2.2.8.4.5.8	Counter	read-only	Indicates the number of seconds that Radio current1 out of limits.
INT hzOduRadio1DrainCurrentOutOfLimitTrap	1.3.6.1.4.1.7262.2.2.9.26	INTEGER	read-write	Enables or disables the radioCurrentOutOfLimitTrap trap.
NTF hzOduRadio1DrainCurrentOutOfLimitV1Trap	1.3.6.1.4.1.7262.2.2.9.0.42			Radio current out of limits.
INT hzOduRadio1OperStatus	1.3.6.1.4.1.7262.2.2.5.1.3.1	INTEGER	read-only	The current operational state of the interface. Testing indicates that no operational packets can be passed. Testing also indicates that a firmware upgrade may be in progress
INT hzOduRadio1PowerOption	1.3.6.1.4.1.7262.2.2.5.1.3.4	INTEGER	read-only	This indicates the power option of the radio: normal or high power.
INT hzOduRadio1ProgrammedAntennaDiameter	1.3.6.1.4.1.7262.2.2.5.1.3.3	INTEGER	read-write	This defines the diameter of the antenna used by the system represented in inches.
INT hzOduRadio1SynthLostLock	1.3.6.1.4.1.7262.2.2.8.4.5.1	INTEGER	read-only	Loss of signal lock from IF Synthesizer.
NTF hzOduRadio1SynthLostLockClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.37			IF synth Lock is lost cleared.
CTR hzOduRadio1SynthLostLockCount	1.3.6.1.4.1.7262.2.2.8.4.5.2	Counter	read-only	Indicates the number of seconds that Loss of signal lock from IF Synthesizer.
INT hzOduRadio1SynthLostLockTrap	1.3.6.1.4.1.7262.2.2.9.23	INTEGER	read-write	Enables or disables the ifSythLostLock trap.
NTF hzOduRadio1SynthLostLockV1Trap	1.3.6.1.4.1.7262.2.2.9.0.36			IF synth Lock is lost.
INT hzOduRadio1TempCompCalTableNotAvail	1.3.6.1.4.1.7262.2.2.8.4.5.3	INTEGER	read-only	Temp comp table not available.
NTF hzOduRadio1TempCompCalTableNotAvailableClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.39			Temp comp table not available cleared.
NTF hzOduRadio1TempCompCalTableNotAvailableV1Trap	1.3.6.1.4.1.7262.2.2.9.0.38			Temp comp table not available.
CTR hzOduRadio1TempCompCalTableNotAvailCount	1.3.6.1.4.1.7262.2.2.8.4.5.4	Counter	read-only	Indicates the number of seconds that Temp comp table not available.
INT hzOduRadio1TempCompCalTableNotAvailTrap	1.3.6.1.4.1.7262.2.2.9.24	INTEGER	read-write	Enables or disables the tempCompCalTableNotAvailable trap.
INT hzOduRadio1Temperature	1.3.6.1.4.1.7262.2.2.5.1.3.6	INTEGER	read-only	The Radio temperature in degree Centigrade. The actual temperature is got by dividing the number by 10. e.g. -432 is actually -43.2 degree centigrade.
INT hzOduRadio1TemperatureOutOfLimit	1.3.6.1.4.1.7262.2.2.8.4.5.9	INTEGER	read-only	Radio temperature out of limits.
NTF hzOduRadio1TemperatureOutOfLimitClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.45			Radio temperature out of limits cleared.
CTR hzOduRadio1TemperatureOutOfLimitCount	1.3.6.1.4.1.7262.2.2.8.4.5.10	Counter	read-only	Indicates the number of seconds that Radio temperature out of limits.
INT hzOduRadio1TemperatureOutOfLimitTrap	1.3.6.1.4.1.7262.2.2.9.27	INTEGER	read-write	Enables or disables the radioTemperatureOutOfLimitTrap trap.
NTF hzOduRadio1TemperatureOutOfLimitV1Trap	1.3.6.1.4.1.7262.2.2.9.0.44			Radio temperature out of limits.
INT hzOduRadio1TransmitPowerDbm	1.3.6.1.4.1.7262.2.2.5.1.3.2	INTEGER	read-write	This defines the transmit level of the radio. If ATPC is enabled, you can't change the transmit power. The power you see is divided by 10. e.g. A display of 133 is actually 13.3 dBm. If the radio is operational and not muted, it is the current transmitting power. If the radio is operational and muted, it is the programmed transmitting power, and will transmit at this level when the radio is un-muted. If the radio is not operational it is the programmed transmitting power, and will transmit at this level when the radio is operational and not muted. If the radio does not have transmit calibration tables programmed into its EEPROM, this transmit power level cannot be used as it is not possible to accurately calculate the actual transmit level. In this case this object will return -99.
INT hzOduRadio1TxDetectorPwrBelowThresh	1.3.6.1.4.1.7262.2.2.8.4.5.5	INTEGER	read-only	Tx power detector below threshold 1.
NTF hzOduRadio1TxDetectorPwrBelowThreshClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.41			Tx power detector below threshold cleared.
CTR hzOduRadio1TxDetectorPwrBelowThreshCount	1.3.6.1.4.1.7262.2.2.8.4.5.6	Counter	read-only	Indicates the number of seconds that Tx power detector below threshold 1.
INT hzOduRadio1TxDetectorPwrBelowThreshTrap	1.3.6.1.4.1.7262.2.2.9.25	INTEGER	read-write	Enables or disables the txDetectorPwrBelowThresh trap.
NTF hzOduRadio1TxDetectorPwrBelowThreshV1Trap	1.3.6.1.4.1.7262.2.2.9.0.40			Tx power detector below threshold.
INT hzOduRadio1TxState	1.3.6.1.4.1.7262.2.2.5.1.3.5	INTEGER	read-only	This indicates the power option of the radio: normal or high power.
INT hzOduRadioBand	1.3.6.1.4.1.7262.2.2.6.1	INTEGER	read-write	The radio frequency standard used in the system. Frequency bands are divided into sub bands. ie FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and fcc23d which make up the entire FCC23 band
hzOduRadius	1.3.6.1.4.1.7262.2.2.17
IP hzOduRadiusActiveHostIpAddress	1.3.6.1.4.1.7262.2.2.17.5.1.3	IpAddress	read-only	The IP address of the active radius server.
IP hzOduRadiusCfgdHostIpAddress	1.3.6.1.4.1.7262.2.2.17.5.1.2	IpAddress	read-write	The IP address of the configured radius server.
INT hzOduRadiusServerDeadTime	1.3.6.1.4.1.7262.2.2.17.3	INTEGER	read-only	Time to declare an unresponsive server 'dead'
hzOduRadiusServerEntry	1.3.6.1.4.1.7262.2.2.17.5.1		not-accessible	Contains the sntp server information
INT hzOduRadiusServerIndex	1.3.6.1.4.1.7262.2.2.17.5.1.1	INTEGER	read-only	A unique value for each server.
INT hzOduRadiusServerReTransmit	1.3.6.1.4.1.7262.2.2.17.4	INTEGER	read-only	Maximum number of retransmits to an unresponsive server
hzOduRadiusServerTable	1.3.6.1.4.1.7262.2.2.17.5		not-accessible	Table containing radius server entries
INT hzOduRadiusServerTimeOut	1.3.6.1.4.1.7262.2.2.17.2	INTEGER	read-only	Timeout period for authentication requests
INT hzOduRadiusSuperUserAuthentication	1.3.6.1.4.1.7262.2.2.17.1	INTEGER	read-write	The set strict mode on or off
hzOduRapidLinkShutdown	1.3.6.1.4.1.7262.2.2.14
hzOduRapidLinkShutdownVer1	1.3.6.1.4.1.7262.2.2.14.1
hzOduRapidLinkShutdownVer2	1.3.6.1.4.1.7262.2.2.14.2
INT hzOduResetSystem	1.3.6.1.4.1.7262.2.2.1.1.1	INTEGER	write-only	Writing '1' to this object resets the NIC, Modem, and radio.
STR hzOduRfAssemblylNo	1.3.6.1.4.1.7262.2.2.1.3.1.6	DisplayString	read-only	A textual string containing assembly no of the RF.
STR hzOduRfSerialNo	1.3.6.1.4.1.7262.2.2.1.3.1.5	DisplayString	read-only	A textual string containing Serial no of the RF.
INT hzOduRlsEnable	1.3.6.1.4.1.7262.2.2.14.1.1	INTEGER	read-write	The Rapid Link Shutdown feature: enabled or disabled. Changing this option requires a system reset.
INT hzOduRlsSampleTimeInMilliSeconds	1.3.6.1.4.1.7262.2.2.14.1.9	INTEGER	read-write
INT hzOduSaveMIB	1.3.6.1.4.1.7262.2.2.1.1.2	INTEGER	write-only	Writing '1' to this object save all MIB values. Note: If the horizon type is 'apng120' or 'apng170' and the radio band doesn't match the horizon type, Mib can't be saved.
hzOduSessionUserInformation	1.3.6.1.4.1.7262.2.2.11.7
hzOduSnmp	1.3.6.1.4.1.7262.2.2.10
INT hzOduSnmpManagerActivated	1.3.6.1.4.1.7262.2.2.10.4.1.4	INTEGER	read-only	Specifies whether a specific manager is allowed to access the system
STR hzOduSnmpManagerAnyCommunityName	1.3.6.1.4.1.7262.2.2.10.2	DisplayString	read-only	The community string name used by the 'any' manager.
STR hzOduSnmpManagerCommunityName	1.3.6.1.4.1.7262.2.2.10.4.1.3	DisplayString	read-only	The community string name used by the manager.
IP hzOduSnmpManagerIpAddress	1.3.6.1.4.1.7262.2.2.10.4.1.2	IpAddress	read-only	The IP address of the Manager.
hzOduSnmpManagersEntry	1.3.6.1.4.1.7262.2.2.10.4.1		not-accessible	Contains the snmp manager information
INT hzOduSnmpManagersIndex	1.3.6.1.4.1.7262.2.2.10.4.1.1	INTEGER	read-only	A unique value for each manager.
hzOduSnmpManagersTable	1.3.6.1.4.1.7262.2.2.10.4		not-accessible	Table containing snmp manager entries
INT hzOduSnmpSetRequests	1.3.6.1.4.1.7262.2.2.10.3	INTEGER	read-only	Indicates whether SNMP SET requests are allowed.
INT hzOduSnmpTrapHostActivated	1.3.6.1.4.1.7262.2.2.9.1.1.5	INTEGER	read-only	Specifies whether traps are to be sent to this specific host or not
STR hzOduSnmpTrapHostCommunityName	1.3.6.1.4.1.7262.2.2.9.1.1.4	DisplayString	read-only	The community string name used in Traps.
hzOduSnmpTrapHostEntry	1.3.6.1.4.1.7262.2.2.9.1.1		not-accessible	The snmp trap host entry containing all the trap host information
INT hzOduSnmpTrapHostIndex	1.3.6.1.4.1.7262.2.2.9.1.1.1	INTEGER	read-only	A unique value for each trap host.
IP hzOduSnmpTrapHostIpAddress	1.3.6.1.4.1.7262.2.2.9.1.1.3	IpAddress	read-only	Indicates snmp trap host IP address.
INT hzOduSnmpTrapHostMode	1.3.6.1.4.1.7262.2.2.9.1.1.2	INTEGER	read-only	Indicates how the snmp trap host is obtained for the system.
hzOduSnmpTrapHostTable	1.3.6.1.4.1.7262.2.2.9.1		not-accessible	Table containing SNMP trap host entries.
INT hzOduSnmpUserAccess	1.3.6.1.4.1.7262.2.2.10.1	INTEGER	read-only	Specifies the user access to the system.If access is set to managers then only managers with there ip addresses set in snmpManagersTable will be able to gain snmp access to the system. If access is set to any then any manager will be able to gain snmp access to the system
INT hzOduSnmpV3ManagerActivated	1.3.6.1.4.1.7262.2.2.10.5.1.7	INTEGER	read-only	Specifies whether a specific v3 manager is allowed to access the system
STR hzOduSnmpV3ManagerAuthPassword	1.3.6.1.4.1.7262.2.2.10.5.1.4	DisplayString	read-only	The authentication password of the v3 Manager.
INT hzOduSnmpV3ManagerAuthProtocol	1.3.6.1.4.1.7262.2.2.10.5.1.3	INTEGER	read-only	The authentication alogorithm used by the v3 manager.
STR hzOduSnmpV3ManagerPrivPassword	1.3.6.1.4.1.7262.2.2.10.5.1.6	DisplayString	read-only	The privacy password of the v3 Manager.
INT hzOduSnmpV3ManagerPrivProtocol	1.3.6.1.4.1.7262.2.2.10.5.1.5	INTEGER	read-only	The privacy encryiption alogorithm used by the v3 manager.
hzOduSnmpV3ManagersEntry	1.3.6.1.4.1.7262.2.2.10.5.1		not-accessible	Contains the snmp v3 manager information
INT hzOduSnmpV3ManagersIndex	1.3.6.1.4.1.7262.2.2.10.5.1.1	INTEGER	read-only	A unique value for each v3 manager.
hzOduSnmpV3ManagersTable	1.3.6.1.4.1.7262.2.2.10.5		not-accessible	Table containing snmp V3 manager entries
STR hzOduSnmpV3ManagerUserName	1.3.6.1.4.1.7262.2.2.10.5.1.2	DisplayString	read-only	The user name of the v3 Manager.
hzOduSnmpV3TrapHostsEntry	1.3.6.1.4.1.7262.2.2.9.2.1		not-accessible	Contains the snmp v3 trap host information
INT hzOduSnmpV3TrapHostsIndex	1.3.6.1.4.1.7262.2.2.9.2.1.1	INTEGER	read-only	A unique value for each v3 trap host.
hzOduSnmpV3TrapHostsTable	1.3.6.1.4.1.7262.2.2.9.2		not-accessible	Table containing snmp V3 trap host entries
hzOduSntp	1.3.6.1.4.1.7262.2.2.15
INT hzOduSntpEnable	1.3.6.1.4.1.7262.2.2.15.1	INTEGER	read-write	Indicates whether SNTP feature is enabled.
INT hzOduSntpOffset	1.3.6.1.4.1.7262.2.2.15.2	INTEGER	read-write	System time offset from GMT.
hzOduSntpServerEntry	1.3.6.1.4.1.7262.2.2.15.3.1		not-accessible	Contains the sntp server information
INT hzOduSntpServerIndex	1.3.6.1.4.1.7262.2.2.15.3.1.1	INTEGER	read-only	A unique value for each server.
IP hzOduSntpServerIpAddress	1.3.6.1.4.1.7262.2.2.15.3.1.2	IpAddress	read-write	The IP address of the server.
INT hzOduSntpServerStatus	1.3.6.1.4.1.7262.2.2.15.3.1.3	INTEGER	read-only	The status of the sntp server.
INT hzOduSntpServerStratum	1.3.6.1.4.1.7262.2.2.15.3.1.4	INTEGER	read-only	Specifies the stratum of a server, 0 for failed server
NTF hzOduSntpServersUnreachableClearedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.12			At least one of SNTP servers is reachable
INT hzOduSntpServersUnreachableTrap	1.3.6.1.4.1.7262.2.2.9.10	INTEGER	read-write	Enables or disables the trap.
NTF hzOduSntpServersUnreachableV1Trap	1.3.6.1.4.1.7262.2.2.9.0.11			Can't reach any of the sntp servers
hzOduSntpServerTable	1.3.6.1.4.1.7262.2.2.15.3		not-accessible	Table containing sntp server entries
INT hzOduSntpServerUnavailableAlarm	1.3.6.1.4.1.7262.2.2.8.2.9	INTEGER	read-only	All of the SNTP servers are not available.
CTR hzOduSntpServerUnavailableAlarmCount	1.3.6.1.4.1.7262.2.2.8.2.10	Counter	read-only	Indicates how long in seconds all of the SNTP servers are not available.
INT hzOduSshAccessMode	1.3.6.1.4.1.7262.2.2.3.7	INTEGER	read-write	Indicates whether ssh access is allowed.
IP hzOduSubnetMask	1.3.6.1.4.1.7262.2.2.3.4	IpAddress	read-only	The subnet mask for the network interface card.
hzOduSwInventory	1.3.6.1.4.1.7262.2.2.1.3.2
hzOduSysGeneral	1.3.6.1.4.1.7262.2.2.1.1
hzOduSysRedundancy	1.3.6.1.4.1.7262.2.2.1.7
hzOduSysSpeed	1.3.6.1.4.1.7262.2.2.1.2
hzOduSystem	1.3.6.1.4.1.7262.2.2.1
hzOduSystemAlarms	1.3.6.1.4.1.7262.2.2.8.2
INT hzOduSystemCurrentSpeed	1.3.6.1.4.1.7262.2.2.1.2.1	INTEGER	read-write	Changes the working speed of the horizon. Writes are only valid if system is a FLEX. Due to backwards compatibility issue, 0 value should be treated as 0 Mbps.
INT hzOduSystemLicensedSpeed	1.3.6.1.4.1.7262.2.2.1.2.2	INTEGER	read-only	Indicates the maximum speed that this system can operate at. Due to backwards compatibility issue, 0 value should be treated as 0 Mbps.
INT hzOduSystemMode	1.3.6.1.4.1.7262.2.2.1.2.3	INTEGER	read-only	Indicates the specific type of system this is.
STR hzOduSystemOmniVersionNo	1.3.6.1.4.1.7262.2.2.1.3.2.1	DisplayString	read-only	The version number of the Omni.
INT hzOduSystemRedundancy	1.3.6.1.4.1.7262.2.2.1.1.5	INTEGER	read-write	Sets system redundancy on/off. If there are any radio failures then the system will automatically switch to redundant system.
STR hzOduSystemRedundancyLinkStatus	1.3.6.1.4.1.7262.2.2.1.7.3	DisplayString	read-only	Indicates the redundancy link status.
INT hzOduSystemRedundancyMode	1.3.6.1.4.1.7262.2.2.1.7.1	INTEGER	read-write	allows the user to set system redundancy mode: [ off \| primary-hsb-1wire \| secondary-hsb-1wire \| primary-hsb-2wire \| secondary-hsb-2wire ]
INT hzOduSystemRedundancyOverride	1.3.6.1.4.1.7262.2.2.1.7.2	INTEGER	read-write	Allows the user to override the active link. User can forces the link to stay on either primary or secondary link.
INT hzOduSystemRedundancyStandbyEnetState	1.3.6.1.4.1.7262.2.2.1.7.4	INTEGER	read-write	Allows the user to set standby enet(port1) state.
INT hzOduSystemRedundancyStateSwitch	1.3.6.1.4.1.7262.2.2.1.7.5	INTEGER	write-only	Allows the user to switch redundancy state.
INT hzOduTelnetAccessMode	1.3.6.1.4.1.7262.2.2.3.6	INTEGER	read-write	Indicates whether Telnet access is allowed.
STR hzOduTime	1.3.6.1.4.1.7262.2.2.7.2	DisplayString	read-only	A string in the format as follows: aa:bb:cc:dd Where aa = hour of day ( range 00 to 23 ) bb = minute of hour ( range 00 to 59 ) cc = second of minute( range 00 to 59 ) dd = hundredths of second (range 00 to 99)
hzOduTraps	1.3.6.1.4.1.7262.2.2.9
INT hzOduTtyManagementSessionCommencedTrap	1.3.6.1.4.1.7262.2.2.9.28	INTEGER	read-write	Specifies whether this trap is to be sent or not
INT hzOduTtyManagementSessionTerminatedTrap	1.3.6.1.4.1.7262.2.2.9.29	INTEGER	read-write	Specifies whether this trap is to be sent or not
NTF hzOduTtySessionCommencedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.46			A person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap.
NTF hzOduTtySessionTerminatedV1Trap	1.3.6.1.4.1.7262.2.2.9.0.47			A person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap.
hzOduTtySessionUser1	1.3.6.1.4.1.7262.2.2.11.1
INT hzOduTtySessionUser1ConnectionType	1.3.6.1.4.1.7262.2.2.11.1.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser1Name	1.3.6.1.4.1.7262.2.2.11.1.1	DisplayString	read-only	The username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.
INT hzOduTtySessionUser1State	1.3.6.1.4.1.7262.2.2.11.1.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
hzOduTtySessionUser2	1.3.6.1.4.1.7262.2.2.11.2
INT hzOduTtySessionUser2ConnectionType	1.3.6.1.4.1.7262.2.2.11.2.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser2Name	1.3.6.1.4.1.7262.2.2.11.2.1	DisplayString	read-only	The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
INT hzOduTtySessionUser2State	1.3.6.1.4.1.7262.2.2.11.2.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
hzOduTtySessionUser3	1.3.6.1.4.1.7262.2.2.11.3
INT hzOduTtySessionUser3ConnectionType	1.3.6.1.4.1.7262.2.2.11.3.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser3Name	1.3.6.1.4.1.7262.2.2.11.3.1	DisplayString	read-only	The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
INT hzOduTtySessionUser3State	1.3.6.1.4.1.7262.2.2.11.3.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
hzOduTtySessionUser4	1.3.6.1.4.1.7262.2.2.11.4
INT hzOduTtySessionUser4ConnectionType	1.3.6.1.4.1.7262.2.2.11.4.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser4Name	1.3.6.1.4.1.7262.2.2.11.4.1	DisplayString	read-only	The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
INT hzOduTtySessionUser4State	1.3.6.1.4.1.7262.2.2.11.4.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
hzOduTtySessionUser5	1.3.6.1.4.1.7262.2.2.11.5
INT hzOduTtySessionUser5ConnectionType	1.3.6.1.4.1.7262.2.2.11.5.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser5Name	1.3.6.1.4.1.7262.2.2.11.5.1	DisplayString	read-only	The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
INT hzOduTtySessionUser5State	1.3.6.1.4.1.7262.2.2.11.5.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
hzOduTtySessionUser6	1.3.6.1.4.1.7262.2.2.11.6
INT hzOduTtySessionUser6ConnectionType	1.3.6.1.4.1.7262.2.2.11.6.2	INTEGER	read-only	The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUser6Name	1.3.6.1.4.1.7262.2.2.11.6.1	DisplayString	read-only	The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
INT hzOduTtySessionUser6State	1.3.6.1.4.1.7262.2.2.11.6.3	INTEGER	read-only	The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
INT hzOduTtySessionUserConnectionType	1.3.6.1.4.1.7262.2.2.11.7.2	INTEGER	read-only	NOT IMPLEMENTED. Object type placeholder for connection type for SNMP traps. The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
STR hzOduTtySessionUserName	1.3.6.1.4.1.7262.2.2.11.7.1	DisplayString	read-only	NOT IMPLEMENTED. Object type placeholder for username string for SNMP traps. The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.
STR hzOduTxHighFreqChannelIndex	1.3.6.1.4.1.7262.2.2.6.3.1.2	DisplayString	read-only	The channel index for the frequency.
hzOduTxHighFreqEntry	1.3.6.1.4.1.7262.2.2.6.3.1		not-accessible	A txHighFrequency entry containing all the frequency values
INT hzOduTxHighFreqIndex	1.3.6.1.4.1.7262.2.2.6.3.1.1	INTEGER	read-only	A unique value for each frequency channel.
INT hzOduTxHighFreqProgrammed	1.3.6.1.4.1.7262.2.2.6.3.1.5	INTEGER	read-write	Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.
INT hzOduTxHighFreqReceiveRfFrequency	1.3.6.1.4.1.7262.2.2.6.3.1.4	INTEGER	read-only	The RF RX frequency in MHz.
hzOduTxHighFreqTable	1.3.6.1.4.1.7262.2.2.6.3		not-accessible	A table of txHigh frequency settings for the system
INT hzOduTxHighFreqTransmitRfFrequency	1.3.6.1.4.1.7262.2.2.6.3.1.3	INTEGER	read-only	The RF TX frequency in MHz.
STR hzOduTxLowFreqChannelIndex	1.3.6.1.4.1.7262.2.2.6.4.1.2	DisplayString	read-only	The channel index for the frequency.
hzOduTxLowFreqEntry	1.3.6.1.4.1.7262.2.2.6.4.1		not-accessible	A hzOduTxLowFrequeny entry containing the frequency values for a specific index
INT hzOduTxLowFreqIndex	1.3.6.1.4.1.7262.2.2.6.4.1.1	INTEGER	read-only	A unique value for each frequency channel.
INT hzOduTxLowFreqProgrammed	1.3.6.1.4.1.7262.2.2.6.4.1.5	INTEGER	read-write	Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.
INT hzOduTxLowFreqReceiveRfFrequency	1.3.6.1.4.1.7262.2.2.6.4.1.4	INTEGER	read-only	The RF RX frequency in MHz.
hzOduTxLowFreqTable	1.3.6.1.4.1.7262.2.2.6.4		not-accessible	A table of txLow frequency settings for the system
INT hzOduTxLowFreqTransmitRfFrequency	1.3.6.1.4.1.7262.2.2.6.4.1.3	INTEGER	read-only	The RF TX frequency in MHz.
STR hzOduUniquePeerAuthenticationKey	1.3.6.1.4.1.7262.2.2.2.1	DisplayString	read-write	The serial number of the peer node that this node will communicate with. This is only used when authentication mode is set to unique.
STR hzOduUnitAssemblylNo	1.3.6.1.4.1.7262.2.2.1.3.1.2	DisplayString	read-only	A textual string containing assembly no of the Unit.
STR hzOduUnitSerialNo	1.3.6.1.4.1.7262.2.2.1.3.1.1	DisplayString	read-only	A textual string containing Serial no of the Unit.
STR hzOduUpgradeLicensedSpeed	1.3.6.1.4.1.7262.2.2.1.2.4	DisplayString	write-only	Enter your apngFLEX key here along with the maximum speed for that key to upgrade the FLEX system. Format: [speed] [key] Example: 50 abc123
INT hzOduVlanTagEnable	1.3.6.1.4.1.7262.2.2.3.8	INTEGER	read-write	Indicates whether VLAN tagging is enabled.
INT hzOduVlanTagId	1.3.6.1.4.1.7262.2.2.3.9	INTEGER	read-write
INT hzOduVlanTagPriority	1.3.6.1.4.1.7262.2.2.3.10	INTEGER	read-write
hzOduWirelessInterface	1.3.6.1.4.1.7262.2.2.5
hzOduWirelessInterfaceAlarms	1.3.6.1.4.1.7262.2.2.8.4
hzOduWirelessPort1	1.3.6.1.4.1.7262.2.2.5.1
STR hzOduWirelessPort1Description	1.3.6.1.4.1.7262.2.2.5.1.1	DisplayString	read-only	Describes the functionality of the Wireless Interface1
INT hzOduWritePrimaryRlsMonitorParametersToSystem	1.3.6.1.4.1.7262.2.2.14.2.5	INTEGER	read-write	This object has changed - This writes RLS soft and hard fault monitor parameters to RAM Reading this object returns '1'.
INT hzOduWriteRlsMonitorParametersToSystem	1.3.6.1.4.1.7262.2.2.14.1.8	INTEGER	read-write	This writes the following parameters to RAM: hysterisisErredFramesPerMilliSecond, hysterisisErredMilliSeconds, hysterisisUnerredFramesPerMilliSecond, hysterisisUnerredMilliSeconds. Reading this object returns '1'.
NTF linkDown	1.3.6.1.2.1.11.0.1			A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration.
NTF linkUp	1.3.6.1.2.1.11.0.2			A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up.
INT snmpV3TrapHostActivated	1.3.6.1.4.1.7262.2.2.9.2.1.8	INTEGER	read-only	Specifies whether a specific v3 trap host is allowed to access the system
STR snmpV3TrapHostAuthPassword	1.3.6.1.4.1.7262.2.2.9.2.1.5	DisplayString	read-only	The authentication password of the v3 trap host.
INT snmpV3TrapHostAuthProtocol	1.3.6.1.4.1.7262.2.2.9.2.1.4	INTEGER	read-only	The authentication alogorithm used by the v3 trap host.
IP snmpV3TrapHostIpAddress	1.3.6.1.4.1.7262.2.2.9.2.1.2	IpAddress	read-only	Indicates snmp trap host IP address.
STR snmpV3TrapHostPrivPassword	1.3.6.1.4.1.7262.2.2.9.2.1.7	DisplayString	read-only	The privacy password of the v3 trap host.
INT snmpV3TrapHostPrivProtocol	1.3.6.1.4.1.7262.2.2.9.2.1.6	INTEGER	read-only	The privacy encryiption alogorithm used by the v3 trap host.
STR snmpV3TrapHostUserName	1.3.6.1.4.1.7262.2.2.9.2.1.3	DisplayString	read-only	The user name of the v3 trap host.

RFC description

DragonWave Horizon ODU wireless microwave MIB for system, network, and QoS management.

Start monitoring DragonWave Horizon microwave radio ODU (Outdoor Unit) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HORIZON-ODU-MIB

What Is HORIZON-ODU-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description