HAWK-I2-MIB

All MIBs › HAWK-I2-MIB

Organization: Sinetica Corporation

Last Updated: 2006-06-27

Category: Hardware and Environment

Description: Monitors environmental and power parameters for Sinetica Hawk-I2 intelligent monitoring units in data centers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HAWK-I2-MIB?

HAWK-I2-MIB is a Sinetica Corporation (enterprise OID 3711) proprietary MIB for the Sinetica Hawk-i2 environmental-monitoring unit. Its objects cover IP-select/insert settings, temperature-scale flag, a THA (Temperature/Humidity/Analog) channel table (channel, reading-set, name, location, auto-detect flag, type, value, scaling, offset, hysteresis), and a threshold table (channel, reading-set, upper/lower control/warning limits) with a trap-enable table. As a status/performance MIB it lets an administrator watch environmental sensor readings against configured control/warning limits on a Sinetica Hawk-i2 unit. It is deployed on the Sinetica Corporation Hawk-i2 environmental-monitoring unit. Engineers can download the HAWK-I2-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HAWK-I2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Sinetica Corporation Hawk-i2 environmental-monitoring unit

Monitoring Examples

An administrator monitors ipTHAValue against ipTHAThreshUCL/ipTHAThreshLCL to catch an environmental sensor reading outside its control limits on a Sinetica Hawk-i2 unit.

What Can Be Monitored

environmental sensor readings vs. control/warning thresholds

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
sinetica	1.3.6.1.4.1.3711
hawki2MIB	1.3.6.1.4.1.3711.24			The MIB module for the Sinetica Hawk-i2.
traps	1.3.6.1.4.1.3711.24.0
NTF alarmCritical	1.3.6.1.4.1.3711.24.0.1			Critical alarm.
NTF alarmWarning	1.3.6.1.4.1.3711.24.0.2			Warning alarm.
NTF alarmInformation	1.3.6.1.4.1.3711.24.0.3			Information alarm.
NTF alarmCleared	1.3.6.1.4.1.3711.24.0.4			Alarm cleared.
v1	1.3.6.1.4.1.3711.24.1
objects	1.3.6.1.4.1.3711.24.1.1
inputs	1.3.6.1.4.1.3711.24.1.1.1
ipCommon	1.3.6.1.4.1.3711.24.1.1.1.1
ipEnable	1.3.6.1.4.1.3711.24.1.1.1.1.1
INT ipSelect	1.3.6.1.4.1.3711.24.1.1.1.1.1.1	INTEGER	read-write	Selects the channel to be enabled or disabled by ipInsert. A value of 0 selects no channel.
INP ipInsert	1.3.6.1.4.1.3711.24.1.1.1.1.1.2	InputDataType	read-write	Inserts or removes the channel selected by ipSelect - causes an entry for that channel to be created or deleted in the relevant tables. - Read behaviour is undefined.
ipTHA	1.3.6.1.4.1.3711.24.1.1.1.2
INT ipTempScaleFlag	1.3.6.1.4.1.3711.24.1.1.1.2.1	INTEGER	read-write	Temperature scale (Celsius/Fahrenheit) for temperature monitoring.
ipTHATable	1.3.6.1.4.1.3711.24.1.1.1.2.2		not-accessible	A table giving data for all enabled inputs with analogue-type monitoring.
ipTHAEntry	1.3.6.1.4.1.3711.24.1.1.1.2.2.1		not-accessible	A conceptual row containing information about one analogue-type input.
INT ipTHAChan	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.1	INTEGER	read-only	The input number.
ROW ipTHARS	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.2	RowStatus	read-only	The analogue-type input table row status.
STR ipTHAName	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.3	DisplayString	read-write	The name of this input
STR ipTHALocn	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.4	DisplayString	read-only	A system-defined name for the physical location of this input, e.g. MCU.
T/F ipTHAAutoDetect	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.5	TruthValue	read-write	Indicates that the type of data this input is monitoring is selected automatically.
INP ipTHAType	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.6	InputDataType	read-write	Indicates the type of data this input is monitoring.
INT ipTHAValue	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.7	INTEGER	read-only	The current reading in the relevant measurement units.
INT ipTHAScaling	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.8	INTEGER	read-write	Scaling factor for ipTHAValue when ipTHAType=analogue.
INT ipTHAOffset	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.9	INTEGER	read-write	Calibration offset in the same units as for ipTHAValue.
INT ipTHAHysteresis	1.3.6.1.4.1.3711.24.1.1.1.2.2.1.10	INTEGER	read-write	Hysteresis on threshold levels in the same units as for ipTHAValue.
ipTHATrapsCfg	1.3.6.1.4.1.3711.24.1.1.1.2.3
ipTHAThreshTable	1.3.6.1.4.1.3711.24.1.1.1.2.3.1		not-accessible	A table listing the trap threshold levels for all enabled inputs with analogue-type monitoring.
ipTHAThreshEntry	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1		not-accessible	A conceptual row containing threshold information for one analogue-type input.
INT ipTHAThreshChan	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.1	INTEGER	read-only	The input number.
ROW ipTHAThreshRS	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.2	RowStatus	read-only	The analogue-type input table row status.
INT ipTHAUCL	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.3	INTEGER	read-write	The Upper Critical Limit for this input in the same units as for ipTHAValue.
INT ipTHAUWL	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.4	INTEGER	read-write	The Upper Warning Limit for this input in the same units as for ipTHAValue.
INT ipTHALWL	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.5	INTEGER	read-write	The Lower Warning Limit for this input in the same units as for ipTHAValue.
INT ipTHALCL	1.3.6.1.4.1.3711.24.1.1.1.2.3.1.1.6	INTEGER	read-write	The Lower Critical Limit for this input in the same units as for ipTHAValue.
ipTHATrapEnTable	1.3.6.1.4.1.3711.24.1.1.1.2.3.2		not-accessible	The table that controls trap enabling for all enabled inputs with analogue-type monitoring.
ipTHATrapEnEntry	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1		not-accessible	A conceptual row containing trap enabling information for one analogue-type input.
INT ipTHATrapEnChan	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.1	INTEGER	read-only	The input number.
ROW ipTHATrapEnRS	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.2	RowStatus	read-only	The analogue-type input table row status.
T/F ipTHAUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.3	TruthValue	read-write	Enables and disables input UCL alarm traps.
T/F ipTHAUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.4	TruthValue	read-write	Enables and disables input UWL alarm traps.
T/F ipTHALWLTrapEn	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.5	TruthValue	read-write	Enables and disables input LWL alarm traps.
T/F ipTHALCLTrapEn	1.3.6.1.4.1.3711.24.1.1.1.2.3.2.1.6	TruthValue	read-write	Enables and disables input LCL alarm traps.
ipTHATrapPerTable	1.3.6.1.4.1.3711.24.1.1.1.2.3.3		not-accessible	The table that controls trap repetition for all enabled inputs with analogue-type monitoring.
ipTHATrapPerEntry	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1		not-accessible	A conceptual row containing trap repetition information for one analogue-type input.
INT ipTHATrapPerChan	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.1	INTEGER	read-only	The input number.
ROW ipTHATrapPerRS	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.2	RowStatus	read-only	The table row status.
INT ipTHATrapUCLPer	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.3	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
INT ipTHATrapUWLPer	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.4	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
INT ipTHATrapLWLPer	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.5	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
INT ipTHATrapLCLPer	1.3.6.1.4.1.3711.24.1.1.1.2.3.3.1.6	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
ipContact	1.3.6.1.4.1.3711.24.1.1.1.3
ipContTable	1.3.6.1.4.1.3711.24.1.1.1.3.1		not-accessible	A table listing the parameters and data for all enabled inputs with contact-type monitoring.
ipContEntry	1.3.6.1.4.1.3711.24.1.1.1.3.1.1		not-accessible	A conceptual row containing information about one contact input.
INT ipContChan	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.1	INTEGER	read-only	The input number.
ROW ipContRS	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.2	RowStatus	read-only	The contact input table row status.
STR ipContName	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.3	DisplayString	read-write	The name of this input
STR ipContLocn	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.4	DisplayString	read-only	A system-defined name for the physical location of this input, e.g. MCU.
T/F ipContAutoDetect	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.5	TruthValue	read-write	Indicates that the type of data this input is monitoring is selected automatically.
CON ipContNormState	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.6	ContactState	read-write	The normal state for this contact.
INP ipContCurrState	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.7	InputContactState	read-only	The current state of this contact.
INT ipContTrigMode	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.8	INTEGER	read-write	The contact trigger mode, level, +ve edge, -ve edge.
U32 ipContReset	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.9	Unsigned32	read-write	Resets the contact after triggering in edge mode.
INT ipContTrapEn	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.10	INTEGER	read-write	Configure contact input traps.
INT ipContTrapPeriod	1.3.6.1.4.1.3711.24.1.1.1.3.1.1.11	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
outputs	1.3.6.1.4.1.3711.24.1.1.2
opEnable	1.3.6.1.4.1.3711.24.1.1.2.1
INT opSelect	1.3.6.1.4.1.3711.24.1.1.2.1.1	INTEGER	read-write	Selects the channel to be enabled or disabled by opEnable. A value of 0 selects no channel.
ENA opInsert	1.3.6.1.4.1.3711.24.1.1.2.1.2	EnableState	read-write	Enables or disables the channel selected by opSelect - causes an entry for that channel to be created or deleted in the relevant tables. - Read behaviour is undefined.
opTable	1.3.6.1.4.1.3711.24.1.1.2.2		not-accessible	A table listing the parameters and data for all outputs that are enabled and available (i.e. its extension unit is connected).
opEntry	1.3.6.1.4.1.3711.24.1.1.2.2.1		not-accessible	A conceptual row containing information about one output.
INT opChan	1.3.6.1.4.1.3711.24.1.1.2.2.1.1	INTEGER	read-only	The output number.
ROW opRS	1.3.6.1.4.1.3711.24.1.1.2.2.1.2	RowStatus	read-only	The contact input table row status.
STR opName	1.3.6.1.4.1.3711.24.1.1.2.2.1.3	DisplayString	read-write	A user-defined name for this output.
STR opLocn	1.3.6.1.4.1.3711.24.1.1.2.2.1.4	DisplayString	read-only	A system-defined name for the physical location of this output, e.g. MCU.
REL opNormState	1.3.6.1.4.1.3711.24.1.1.2.2.1.5	RelayState	read-write	Sets or reads the required normal state of this output.
REL opCurrState	1.3.6.1.4.1.3711.24.1.1.2.2.1.6	RelayState	read-only	Reads the current state of this output.
U32 opOnDelTime	1.3.6.1.4.1.3711.24.1.1.2.2.1.7	Unsigned32	read-write	Sets the 'on' delay time for this output.
U32 opOffDelTime	1.3.6.1.4.1.3711.24.1.1.2.2.1.8	Unsigned32	read-write	Sets the 'off' delay time for this output.
STR opBooleanEqn	1.3.6.1.4.1.3711.24.1.1.2.2.1.9	DisplayString	read-write	Boolean equation string
INT opTrapEn	1.3.6.1.4.1.3711.24.1.1.2.2.1.10	INTEGER	read-write	Configure output traps.
INT opTrapPeriod	1.3.6.1.4.1.3711.24.1.1.2.2.1.11	INTEGER	read-write	Set to 0 disables trap repetition, a value of 30 or higher sets the interval between traps in seconds
OUT opControlState	1.3.6.1.4.1.3711.24.1.1.2.2.1.12	OutputControlState	read-write	Reads the current control state of an output.
keypads	1.3.6.1.4.1.3711.24.1.1.4
kpEnable	1.3.6.1.4.1.3711.24.1.1.4.1
INT kpSelect	1.3.6.1.4.1.3711.24.1.1.4.1.1	INTEGER	read-write	Selects the keypad to be enabled or disabled by kpEnable. A value of 0 selects no keypad.
ENA kpInsert	1.3.6.1.4.1.3711.24.1.1.4.1.2	EnableState	read-write	Enables or disables the keypad selected by kpSelect - causes an entry for that keypad to be created or deleted in the relevant tables. - Read behaviour is undefined.
kpCtlTable	1.3.6.1.4.1.3711.24.1.1.4.2		not-accessible	A table listing the parameters and data for the keypads.
kpCtlEntry	1.3.6.1.4.1.3711.24.1.1.4.2.1		not-accessible	A conceptual row containing information about one keypad.
INT kpNumber	1.3.6.1.4.1.3711.24.1.1.4.2.1.1	INTEGER	read-only	The keypad number.
ROW kpRS	1.3.6.1.4.1.3711.24.1.1.4.2.1.2	RowStatus	read-only	The keypad table row status.
STR kpManufacturer	1.3.6.1.4.1.3711.24.1.1.4.2.1.3	DisplayString	read-write	The name of the manufacturer of the keypad.
STR kpName	1.3.6.1.4.1.3711.24.1.1.4.2.1.4	DisplayString	read-write	A name identifying the keypad.
U32 kpDoorLatchTimeOut	1.3.6.1.4.1.3711.24.1.1.4.2.1.5	Unsigned32	read-write	Time-out value in seconds for which the door latch is held open.
INT kpRtnToStndbyTimeOut	1.3.6.1.4.1.3711.24.1.1.4.2.1.6	INTEGER	read-write	Time-out value in seconds for Return to Standby Mode
T/F kpEntryCodeValid	1.3.6.1.4.1.3711.24.1.1.4.2.1.7	TruthValue	read-only	Set if previous keypad entry was valid.
INT kpDoorOpenTimeOut	1.3.6.1.4.1.3711.24.1.1.4.2.1.8	INTEGER	read-write	Time-out value in seconds for Door Open.
T/F kpRemoteDoorOpen	1.3.6.1.4.1.3711.24.1.1.4.2.1.9	TruthValue	read-write	Set to open the door.
INT kpInUseTrapEn	1.3.6.1.4.1.3711.24.1.1.4.2.1.10	INTEGER	read-write	'keypad in use' trap enable
acus	1.3.6.1.4.1.3711.24.1.1.5
acuEnable	1.3.6.1.4.1.3711.24.1.1.5.1
INT acuSelect	1.3.6.1.4.1.3711.24.1.1.5.1.1	INTEGER	read-write	Selects the ACU to be enabled or disabled by acuEnable. A value of 0 selects no ACU.
ENA acuInsert	1.3.6.1.4.1.3711.24.1.1.5.1.2	EnableState	read-write	Enables or disables the ACU selected by acuSelect - causes an entry for that ACU to be created or deleted in the relevant tables. - Read behaviour is undefined.
acuCtlTable	1.3.6.1.4.1.3711.24.1.1.5.2		not-accessible	A table listing the parameters and data for the ACUs.
acuCtlEntry	1.3.6.1.4.1.3711.24.1.1.5.2.1		not-accessible	A conceptual row containing information about one ACU.
INT acuNumber	1.3.6.1.4.1.3711.24.1.1.5.2.1.1	INTEGER	read-only	The ACU number.
ROW acuCtlRS	1.3.6.1.4.1.3711.24.1.1.5.2.1.2	RowStatus	read-only	The ACU table row status.
STR acuManufacturer	1.3.6.1.4.1.3711.24.1.1.5.2.1.3	DisplayString	read-write	The name of the manufacturer of the ACU.
STR acuName	1.3.6.1.4.1.3711.24.1.1.5.2.1.4	DisplayString	read-write	A name identifying the ACU.
U32 acuDoorLatchTimeOut	1.3.6.1.4.1.3711.24.1.1.5.2.1.5	Unsigned32	read-write	Time-out value in seconds for which the door latch is held open.
INT acuRtnToStndbyTimeOut	1.3.6.1.4.1.3711.24.1.1.5.2.1.6	INTEGER	read-write	Time-out value in seconds for Return to Standby Mode
T/F acuEntryCodeValid	1.3.6.1.4.1.3711.24.1.1.5.2.1.7	TruthValue	read-only	Set if previous ACU entry was valid.
INT acuDoorOpenTimeOut	1.3.6.1.4.1.3711.24.1.1.5.2.1.8	INTEGER	read-write	Time-out value in seconds for Door Open.
T/F acuRemoteDoorOpen	1.3.6.1.4.1.3711.24.1.1.5.2.1.9	TruthValue	read-write	Set to open the door.
INT acuInUseTrapEn	1.3.6.1.4.1.3711.24.1.1.5.2.1.10	INTEGER	read-write	'ACU in use' trap enable
access	1.3.6.1.4.1.3711.24.1.1.6
accUserCtl	1.3.6.1.4.1.3711.24.1.1.6.1
U32 accUserInstance	1.3.6.1.4.1.3711.24.1.1.6.1.1	Unsigned32	read-write	A value of 0 causes an access user to be created in the relevant tables. A non-zero value causes the nominated access user table entries to be deleted.
accUserTable	1.3.6.1.4.1.3711.24.1.1.6.1.2		not-accessible	A table controlling the access users.
accUserEntry	1.3.6.1.4.1.3711.24.1.1.6.1.2.1		not-accessible	A conceptual row containing information about one ACU user.
INT accUserNumber	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.1	INTEGER	read-only	The the access user-table entry number.
ROW accUserRS	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.2	RowStatus	read-only	The access user table row status.
STR accUserName	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.3	DisplayString	read-write	A name identifying the access user.
OCT accUserCode	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.4	OCTET STRING	read-write	The user's access code.
STR accUserPrivileges	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.5	DisplayString	read-write	The ACUs and keypads that the user is allowed to gain access through - comma-separated numerical strings.
STR accUserExpires	1.3.6.1.4.1.3711.24.1.1.6.1.2.1.6	DisplayString	read-write	A text string which specifies when the access code in the row expires. The format is defined by the application.
OCT accUserSetup	1.3.6.1.4.1.3711.24.1.1.6.1.3	OCTET STRING	read-write	A free form octet string for programming accUserTable. The format is defined by the application.
pdus	1.3.6.1.4.1.3711.24.1.1.7
pduCommon	1.3.6.1.4.1.3711.24.1.1.7.1
pdusEnable	1.3.6.1.4.1.3711.24.1.1.7.1.1
INT pduSelect	1.3.6.1.4.1.3711.24.1.1.7.1.1.1	INTEGER	read-write	Selects the PDU to be enabled or disabled by pduEnable. A value of 0 selects no PDU.
ENA pduInsert	1.3.6.1.4.1.3711.24.1.1.7.1.1.2	EnableState	read-write	Enables or disables the PDU selected by pduSelect - causes an entry for that PDU to be created or deleted in the relevant tables. - Read behaviour is undefined.
pduTable	1.3.6.1.4.1.3711.24.1.1.7.1.2		not-accessible	A table containing information about each enabled PDU.
pduEntry	1.3.6.1.4.1.3711.24.1.1.7.1.2.1		not-accessible	A conceptual row containing information about one PDU.
INT pduNumber	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.1	INTEGER	read-only	The PDU number.
ROW pduRS	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.2	RowStatus	read-only	The PDU table row status.
STR pduName	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.3	DisplayString	read-write	A string identifying the PDU.
T/F pduOutEn	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.4	TruthValue	read-write	Enables/disables PDU power outlet control - causes an entry for outlets to be created in each relevant PDU table.
T/F pduMonEn	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.5	TruthValue	read-write	Enables/disables PDU power monitoring - causes an entry for monitoring to be created in each relevant PDU table.
INT pduCommsFail	1.3.6.1.4.1.3711.24.1.1.7.1.2.1.6	INTEGER	read-only	Indicates comms. status for the PDU.
pduOutlets	1.3.6.1.4.1.3711.24.1.1.7.2
pduOutAll	1.3.6.1.4.1.3711.24.1.1.7.2.1
INT pduOutCycleAll	1.3.6.1.4.1.3711.24.1.1.7.2.1.1	INTEGER	read-write	Sets the required state of all power outlets on all connected PDUs.
STR pduOutCycleAllPwd	1.3.6.1.4.1.3711.24.1.1.7.2.1.2	DisplayString	read-write	Controls access to setting the required state of all power outlets on all connected PDUs.
U32 pduOutCycleAllAbort	1.3.6.1.4.1.3711.24.1.1.7.2.1.3	Unsigned32	read-write	Abort command for pduOutCycleAll.
U32 pduOutGlobalCycleDelay	1.3.6.1.4.1.3711.24.1.1.7.2.1.4	Unsigned32	read-write	Sets the delay period for pduOutCycleAll and pduOutCycle commands before they start to execute.
U32 pduOutGlobalRebootTime	1.3.6.1.4.1.3711.24.1.1.7.2.1.5	Unsigned32	read-write	Sets the off to on delay period for a pdu outlet reboot.
U32 pduOutGlobalCycleAbortTime	1.3.6.1.4.1.3711.24.1.1.7.2.1.6	Unsigned32	read-write	Time delay to abort power outlet setting task.
pduOutCmnTable	1.3.6.1.4.1.3711.24.1.1.7.2.2		not-accessible	A table containing information about the power outlets of all PDUs enabled for outlet control.
pduOutCmnEntry	1.3.6.1.4.1.3711.24.1.1.7.2.2.1		not-accessible	A conceptual row containing information about the power outlets of one PDU.
INT pduOutCmnPduNumber	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.1	INTEGER	read-only	The PDU number.
ROW pduOutCmnRS	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.2	RowStatus	read-only	The PDU table row status.
INT pduNumOfOutlets	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.3	INTEGER	read-write	The number of switchable outlets on the PDU - determines the number of entries to be created in the outlet table for the relevant PDU.
INT pduOutCycle	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.4	INTEGER	read-write	Sets the required state of all power outlets on the PDU.
STR pduOutCyclePwd	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.5	DisplayString	read-write	Password controling access to setting the required state of all power outlets on the PDU.
U32 pduOutCycleAbortTask	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.6	Unsigned32	read-write	Abort power outlet setting task.
U32 pduOutCycleAbortTime	1.3.6.1.4.1.3711.24.1.1.7.2.2.1.7	Unsigned32	read-write	Time delay to abort power outlet setting task.
pduOutTable	1.3.6.1.4.1.3711.24.1.1.7.2.3		not-accessible	A table listing the states and descriptions for each outlet on the PDU.
pduOutEntry	1.3.6.1.4.1.3711.24.1.1.7.2.3.1		not-accessible	A row containing information about one PDU outlet.
INT pduOutPduNumber	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.1	INTEGER	read-only	The PDU number on which the outlet resides.
INT pduOutNumber	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.2	INTEGER	read-only	The outlet number.
ROW pduOutRS	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.3	RowStatus	read-only	The PDU table row status.
STR pduOutName	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.4	DisplayString	read-write	A name identifying the outlet.
INT pduOutOn	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.5	INTEGER	read-write	The current state for this outlet.
STR pduOutPwd	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.6	DisplayString	read-write	The password for this outlet.
U32 pduOutCycleDelay	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.7	Unsigned32	read-only	The on/off delay for this outlet in seconds.
U32 pduOutRebootPeriod	1.3.6.1.4.1.3711.24.1.1.7.2.3.1.8	Unsigned32	read-only	The pduOutOn reboot off period for this outlet in seconds.
pduMonitor	1.3.6.1.4.1.3711.24.1.1.7.3
pduMonTable	1.3.6.1.4.1.3711.24.1.1.7.3.1		not-accessible	A table containing monitor information for all PDUs enabled for monitoring.
pduMonEntry	1.3.6.1.4.1.3711.24.1.1.7.3.1.1		not-accessible	A conceptual row containing monitor information for one PDU.
INT pduMonPduNumber	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.1	INTEGER	read-only	The PDU number.
ROW pduMonRS	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.2	RowStatus	read-only	The PDU table row status.
INT pduRMSVoltsValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.3	INTEGER	read-only	RMS Volts value in volts
INT pduRMSAmpsValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.4	INTEGER	read-only	RMS current value in 0.1 Amps
INT pduTotalEnergyValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.5	INTEGER	read-only	Total energy value in 0.1 kWh
INT pduMeanKVAValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.6	INTEGER	read-only	Kilo Volt-Amperes value in 0.1 kVA
INT pduMeanKWattsValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.7	INTEGER	read-only	Kilo Watts value in 0.1 kW
INT pduPwrFactorValue	1.3.6.1.4.1.3711.24.1.1.7.3.1.1.8	INTEGER	read-only	Power factor value in 0.01
pduTrapThreshTable	1.3.6.1.4.1.3711.24.1.1.7.3.2		not-accessible	A table containing information about the trap threshold values for all PDUs enabled for monitoring.
pduTrapThreshEntry	1.3.6.1.4.1.3711.24.1.1.7.3.2.1		not-accessible	A conceptual row containing information about the trap threshold values for one PDU.
INT pduTrapThreshPduNumber	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.1	INTEGER	read-only	The PDU number.
ROW pduTrapThreshRS	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.2	RowStatus	read-only	The PDU table row status.
INT pduRMSVoltsUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.3	INTEGER	read-write	rms UCL value in volts
INT pduRMSVoltsUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.4	INTEGER	read-write	rms UWL value in volts
INT pduRMSVoltsLWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.5	INTEGER	read-write	rms LWL value in volts
INT pduRMSVoltsLCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.6	INTEGER	read-write	rms LCL value in volts
INT pduRMSAmpsUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.7	INTEGER	read-write	rms UCL value in 0.1 amps
INT pduRMSAmpsUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.8	INTEGER	read-write	rms UWL value in 0.1 amps
INT pduRMSAmpsLWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.9	INTEGER	read-write	rms LWL value in 0.1 amps
INT pduRMSAmpsLCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.10	INTEGER	read-write	rms LCL value in 0.1 amps
INT pduEnergyUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.11	INTEGER	read-write	Total energy UCL value in 0.1 kWh
INT pduEnergyUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.12	INTEGER	read-write	Total energy UWL value in 0.1 kWh
INT pduMeanKVAUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.13	INTEGER	read-write	Mean kVA UCL value in 0.1 kVA
INT pduMeanKVAUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.14	INTEGER	read-write	Mean kVA UWL value in 0.1 kVA
INT pduMeanKVALWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.15	INTEGER	read-write	Mean kVA LWL value in 0.1 kVA
INT pduMeanKVALCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.16	INTEGER	read-write	Mean kVA LCL value in 0.1 kVA
INT pduMeanKWattsUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.17	INTEGER	read-write	Mean power UCL value in 0.1 kW
INT pduMeanKWattsUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.18	INTEGER	read-write	Mean power UWL value in 0.1 kW
INT pduMeanKWattsLWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.19	INTEGER	read-write	Mean power LWL value in 0.1 kW
INT pduMeanKWattsLCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.20	INTEGER	read-write	Mean power LCL value in 0.1 kW
INT pduPwrFactorUCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.21	INTEGER	read-write	Power factor UCL value in 0.01
INT pduPwrFactorUWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.22	INTEGER	read-write	Power factor UWL value in 0.01
INT pduPwrFactorLWL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.23	INTEGER	read-write	Power factor LWL value in 0.01
INT pduPwrFactorLCL	1.3.6.1.4.1.3711.24.1.1.7.3.2.1.24	INTEGER	read-write	Power factor LCL value in 0.01
pduTrapEnTable	1.3.6.1.4.1.3711.24.1.1.7.3.3		not-accessible	The table which controls threshold value trap enabling for all PDUs enabled for monitoring.
pduTrapEnEntry	1.3.6.1.4.1.3711.24.1.1.7.3.3.1		not-accessible	A conceptual row containing information about one PDU.
INT pduTrapEnPduNumber	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.1	INTEGER	read-only	The PDU number.
ROW pduTrapEnRS	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.2	RowStatus	read-only	The PDU table row status.
T/F pduRMSVoltsUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.3	TruthValue	read-write	Enables Volts UCL trap.
T/F pduRMSVoltsUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.4	TruthValue	read-write	Enables UWL Volts trap.
T/F pduRMSVoltsLWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.5	TruthValue	read-write	Enables LWL Volts trap.
T/F pduRMSVoltsLCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.6	TruthValue	read-write	Enables LCL Volts trap.
T/F pduRMSAmpsUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.7	TruthValue	read-write	Enables UCL current trap.
T/F pduRMSAmpsUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.8	TruthValue	read-write	Enables UWL current trap.
T/F pduRMSAmpsLWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.9	TruthValue	read-write	Enables LWL current trap.
T/F pduRMSAmpsLCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.10	TruthValue	read-write	Enables LCL current trap.
T/F pduEnergyUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.11	TruthValue	read-write	Enables UCL total energy trap.
T/F pduEnergyUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.12	TruthValue	read-write	Enables UWL total energy trap.
T/F pduMeanKVAUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.13	TruthValue	read-write	Enables mean kVA UCL trap.
T/F pduMeanKVAUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.14	TruthValue	read-write	Enables mean kVA UWL trap.
T/F pduMeanKVALWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.15	TruthValue	read-write	Enables mean kVA LWL trap.
T/F pduMeanKVALCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.16	TruthValue	read-write	Enables mean kVA LCL trap.
T/F pduMeanKWattsUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.17	TruthValue	read-write	Enables mean power UCL trap.
T/F pduMeanKWattsUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.18	TruthValue	read-write	Enables mean power UWL trap.
T/F pduMeanKWattsLWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.19	TruthValue	read-write	Enables mean power LWL trap.
T/F pduMeanKWattsLCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.20	TruthValue	read-write	Enables mean power LCL trap.
T/F pduPwrFactorUCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.21	TruthValue	read-write	Enables power factor UCL trap.
T/F pduPwrFactorUWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.22	TruthValue	read-write	Enables power factor UWL trap.
T/F pduPwrFactorLWLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.23	TruthValue	read-write	Enables power factor LWL trap.
T/F pduPwrFactorLCLTrapEn	1.3.6.1.4.1.3711.24.1.1.7.3.3.1.24	TruthValue	read-write	Enables power factor LCL trap.
pduTrapPerTable	1.3.6.1.4.1.3711.24.1.1.7.3.4		not-accessible	The table which controls threshold value trap repetition for all PDUs enabled for monitoring.
pduTrapPerEntry	1.3.6.1.4.1.3711.24.1.1.7.3.4.1		not-accessible	A conceptual row containing information about one PDU.
INT pduTrapPduNumber	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.1	INTEGER	read-only	The PDU number.
ROW pduTrapPerRS	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.2	RowStatus	read-only	The PDU table row status.
INT pduRMSVoltsUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.3	INTEGER	read-write	Sets UCL Volts trap repeat rate in seconds
INT pduRMSVoltsUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.4	INTEGER	read-write	Sets UWL Volts trap repeat rate in seconds
INT pduRMSVoltsLWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.5	INTEGER	read-write	Sets LWL Volts trap repeat rate in seconds
INT pduRMSVoltsLCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.6	INTEGER	read-write	Sets LCL Volts trap repeat rate in seconds
INT pduRMSAmpsUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.7	INTEGER	read-write	Sets UCL current trap repeat rate in seconds
INT pduRMSAmpsUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.8	INTEGER	read-write	Sets UWL current trap repeat rate in seconds
INT pduRMSAmpsLWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.9	INTEGER	read-write	Sets LWL current trap repeat rate in seconds
INT pduRMSAmpsLCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.10	INTEGER	read-write	Sets LCL current trap repeat rate in seconds
INT pduEnergyUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.11	INTEGER	read-write	Sets UCL total energy trap repeat rate in seconds
INT pduEnergyUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.12	INTEGER	read-write	Sets UWL total energy trap repeat rate in seconds
INT pduMeanKVAUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.13	INTEGER	read-write	Sets mean kVA UCL trap repeat rate in seconds
INT pduMeanKVAUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.14	INTEGER	read-write	Sets mean kVA UWL trap repeat rate in seconds
INT pduMeanKVALWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.15	INTEGER	read-write	Sets mean kVA LWL trap repeat rate in seconds
INT pduMeanKVALCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.16	INTEGER	read-write	Sets mean kVA LCL trap repeat rate in seconds
INT pduMeanKWattsUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.17	INTEGER	read-write	Sets mean power UCL trap repeat rate in seconds
INT pduMeanKWattsUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.18	INTEGER	read-write	Sets mean power UWL trap repeat rate in seconds
INT pduMeanKWattsLWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.19	INTEGER	read-write	Sets mean power LWL trap repeat rate in seconds
INT pduMeanKWattsLCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.20	INTEGER	read-write	Sets mean power LCL trap repeat rate in seconds
INT pduPwrFactorUCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.21	INTEGER	read-write	Sets power factor UCL trap repeat rate in seconds
INT pduPwrFactorUWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.22	INTEGER	read-write	Sets power factor UWL trap repeat rate in seconds
INT pduPwrFactorLWLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.23	INTEGER	read-write	Sets power factor LWL trap repeat rate in seconds
INT pduPwrFactorLCLTrapPer	1.3.6.1.4.1.3711.24.1.1.7.3.4.1.24	INTEGER	read-write	Sets power factor LCL trap repeat rate in seconds
inventory	1.3.6.1.4.1.3711.24.1.1.99
STR invProdSignature	1.3.6.1.4.1.3711.24.1.1.99.1	DisplayString	read-only	Product data signature.
STR invProdFormatVer	1.3.6.1.4.1.3711.24.1.1.99.2	DisplayString	read-only	Product data format version.
STR invManufCode	1.3.6.1.4.1.3711.24.1.1.99.3	DisplayString	read-only	Manufacturer code.
STR invOrderNum	1.3.6.1.4.1.3711.24.1.1.99.4	DisplayString	read-only	Order number.
STR invBatchNum	1.3.6.1.4.1.3711.24.1.1.99.5	DisplayString	read-only	Batch number.
STR invProdTestTime	1.3.6.1.4.1.3711.24.1.1.99.6	DisplayString	read-only	Data and time of production test.
STR invUnitName	1.3.6.1.4.1.3711.24.1.1.99.7	DisplayString	read-only	Unit name.
STR invUnitPartNum	1.3.6.1.4.1.3711.24.1.1.99.8	DisplayString	read-only	Unit part number.
STR invHwRevision	1.3.6.1.4.1.3711.24.1.1.99.9	DisplayString	read-only	Hardware revision number.
STR invFwRevision	1.3.6.1.4.1.3711.24.1.1.99.10	DisplayString	read-only	Firmware revision number.
STR invSerialNum	1.3.6.1.4.1.3711.24.1.1.99.11	DisplayString	read-only	Serial number.
IPt invDefaultIPAddrType	1.3.6.1.4.1.3711.24.1.1.99.12	InetAddressType	read-only	The type of the IP addresses.
IP invDefaultIPAddr	1.3.6.1.4.1.3711.24.1.1.99.13	InetAddress	read-only	Default unit IP address.
IP invDefaultSubNetMask	1.3.6.1.4.1.3711.24.1.1.99.14	InetAddress	read-only	Default unit sub-network mask.
IP invDefaultGWAddr	1.3.6.1.4.1.3711.24.1.1.99.15	InetAddress	read-only	Default unit default gateway address.
MAC invMacAddr	1.3.6.1.4.1.3711.24.1.1.99.16	MacAddress	read-only	Unit medium access control (MAC) address.
T/F invOk	1.3.6.1.4.1.3711.24.1.1.99.20	TruthValue	read-only	Confirms that the inventory record isn't corrupted.
INT invInputCount	1.3.6.1.4.1.3711.24.1.1.99.50	INTEGER	read-only	The maximum number of inputs that can be connected to the unit
INT invOutputCount	1.3.6.1.4.1.3711.24.1.1.99.51	INTEGER	read-only	The maximum number of outputs that can be connected to the unit
INT invKeypadCount	1.3.6.1.4.1.3711.24.1.1.99.52	INTEGER	read-only	The maximum number of keypads that can be connected to the unit
INT invAcuCount	1.3.6.1.4.1.3711.24.1.1.99.53	INTEGER	read-only	The maximum number of ACU's that can be connected to the unit
INT invAccessUserCount	1.3.6.1.4.1.3711.24.1.1.99.54	INTEGER	read-only	The maximum number of user entries on the unit
INT invPduCount	1.3.6.1.4.1.3711.24.1.1.99.55	INTEGER	read-only	The maximum number of PDU's that can be connected to the unit
trapInfo	1.3.6.1.4.1.3711.24.1.1.100
U32 trapCode	1.3.6.1.4.1.3711.24.1.1.100.1	Unsigned32	read-only	A decimal number to be carried on notifications of types 1 to 4 identifying the event which caused it. The format of this number is BBEEffCCT where BB is the number of the relevant MIB branch. EE indicates what type of event caused the notification. This value is dependent upon branch number and implementation. CC is the channel number which was the source of the notification. T discriminates the type of data, e.g. temperature. This value is dependent upon branch number and implementation. ff future use. Fields are packed with leading zeros and are set to zero if not relevant to a particular notification.
STR trapDescription	1.3.6.1.4.1.3711.24.1.1.100.2	DisplayString	read-only	A string to be carried on notifications of types 1 to 4 identifying the event which caused it. The format of this string is as follows. Field 1 - type of notification, e.g. warning, critical, etc. Field 2 - data source, e.g. inputs. Generally this relates to a particular MIB branch. Field 3 - channel number, e.g. input 1. Field 4 - event, i.e. what caused the trap. Field 5 - value at which the event occured, e.g. 900, indicating 90% humidity. Field 6 - type of data, e.g. relative humidity Fields are omitted if not relevant to a particular notification.

RFC description

Sinetica Hawk-i2 monitoring unit SNMP MIB. Provides management objects for the Hawk-i2 monitoring platform available in various device library systems.

Start monitoring Sinetica Corporation Hawk-i2 environmental-monitoring unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HAWK-I2-MIB

What Is HAWK-I2-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description