All MIBs › GSM7324-QOS-DIFFSERV-PRIVATE-MIB
Organization: Netgear
Last Updated: 2003-05-06
Category: Technology: QoS, Vendor: Netgear
Description: Netgear GSM7324 switch MIB for proprietary DiffServ QoS configuration beyond standard IETF DiffServ objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is GSM7324-QOS-DIFFSERV-PRIVATE-MIB?
GSM7324-QOS-DIFFSERV-PRIVATE-MIB is a Netgear vendor extension, under the gsm7324QOS branch, that adds proprietary DiffServ QoS configuration objects beyond the standard IETF DIFFSERV-MIB for the GSM7324 switch. It defines traffic classification in agentDiffServClassTable (agentDiffServClassType distinguishing all/any/acl-based classes) backed by agentDiffServClassRuleTable, policy definitions in agentDiffServPolicyTable/agentDiffServPolicyInstTable/agentDiffServPolicyAttrTable, per-policy ingress/egress performance counters in agentDiffServPolicyPerfInTable and agentDiffServPolicyPerfOutTable, and per-interface service attachment plus performance counters in agentDiffServServiceTable/agentDiffServServicePerfTable, along with a global admin-mode object in agentDiffServGenStatusGroup. This exposes both how DiffServ classes/policies are configured and how much traffic each policy is actually matching and acting on per interface, essential for confirming QoS policy is correctly classifying and marking/limiting traffic as intended. It depends on the standard IF-MIB (ifIndex) for interface binding and the base GSM7324-QOS-MIB for its OID anchor. It is deployed on Netgear GSM7324 managed switches, and the GSM7324-QOS-DIFFSERV-PRIVATE-MIB MIB is what administrators load to inspect this proprietary DiffServ configuration and performance data.
IPNetwork Monitor allows you to monitor SNMP objects defined in GSM7324-QOS-DIFFSERV-PRIVATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Netgear GSM7324 managed switch
Monitoring Examples
An operator polls agentDiffServServicePerfTable for a policy attached to a given interface direction (in/out) to see matched-traffic counters, and cross-references agentDiffServClassRuleTable for the ACL-based match criteria; a policy showing zero matched packets despite expected traffic would indicate a misconfigured classification rule failing to match the intended flows.
What Can Be Monitored
- DiffServ class definitions and classification rules
- DiffServ policy definitions and attribute bindings
- per-policy ingress/egress performance counters
- per-interface service attachment and performance statistics
- global DiffServ admin-mode status
This MIB depends on
Related MIBs
Imported Objects
From GSM7324-QOS-MIB
| gsm7324QOS | MODULE-IDENTITY |
From IANAifType-MIB
| IANAifType |
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetPortNumber |
From RFC1155-SMI
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowPointer | |
| RowStatus | |
| StorageType | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using agentDiffServPolicyPerfInOfferedOctets OID:
Select a Netgear GSM7324 managed switch (DiffServ QoS policy/performance) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentDiffServPolicyPerfInOfferedOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the offered octets count for the inbound policy-class instance performance entry. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| gsm7324QOSDiffServPrivate | 1.3.6.1.4.1.4526.1.7.3.4 | |||
| agentDiffServGenStatusGroup | 1.3.6.1.4.1.4526.1.7.3.4.1 | |||
| INT agentDiffServGenStatusAdminMode | 1.3.6.1.4.1.4526.1.7.3.4.1.1 | INTEGER | read-write | DiffServ Admin Mode |
| U32 agentDiffServGenStatusClassTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.2 | Unsigned32 | read-only | Current size of the Class Table |
| U32 agentDiffServGenStatusClassTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.3 | Unsigned32 | read-only | Max size of the Class Table |
| U32 agentDiffServGenStatusClassRuleTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.4 | Unsigned32 | read-only | Current size of Class Rule Table |
| U32 agentDiffServGenStatusClassRuleTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.5 | Unsigned32 | read-only | Max size of the Class Rule Table. |
| U32 agentDiffServGenStatusPolicyTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.6 | Unsigned32 | read-only | Current Size of the Policy Table. |
| U32 agentDiffServGenStatusPolicyTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.7 | Unsigned32 | read-only | Max size of the Policy Table |
| U32 agentDiffServGenStatusPolicyInstTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.8 | Unsigned32 | read-only | Current size of the Policy-Class Instance Table |
| U32 agentDiffServGenStatusPolicyInstTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.9 | Unsigned32 | read-only | Max size of the Policy-Class Instance Table |
| U32 agentDiffServGenStatusPolicyAttrTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.10 | Unsigned32 | read-only | Current size of the Policy Attribute Table |
| U32 agentDiffServGenStatusPolicyAttrTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.11 | Unsigned32 | read-only | Max size of the Policy Attribute Table |
| U32 agentDiffServGenStatusServiceTableSize | 1.3.6.1.4.1.4526.1.7.3.4.1.12 | Unsigned32 | read-only | Current size of the Service Table |
| U32 agentDiffServGenStatusServiceTableMax | 1.3.6.1.4.1.4526.1.7.3.4.1.13 | Unsigned32 | read-only | Max size of the Service Table |
| agentDiffServClassGroup | 1.3.6.1.4.1.4526.1.7.3.4.2 | |||
| U32 agentDiffServClassIndexNextFree | 1.3.6.1.4.1.4526.1.7.3.4.2.1 | Unsigned32 | read-only | This object contains an unused value for classIndex, or a zero to indicate that none exists. |
| agentDiffServClassTable | 1.3.6.1.4.1.4526.1.7.3.4.2.2 | not-accessible | A table of the DiffServ class entries | |
| agentDiffServClassEntry | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1 | not-accessible | Represents entry for a DiffServ traffic class | |
| U32 agentDiffServClassIndex | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.1 | Unsigned32 | not-accessible | The identifier for DiffServ Class entry |
| STR agentDiffServClassName | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.2 | DisplayString | read-create | Name of the DiffServ traffic class |
| INT agentDiffServClassType | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.3 | INTEGER | read-create | The class type indicates how the individual class match criteria are evaluated. For type all, all of the individual match conditions must be true for a packet to be considered a member of the class. For types any and acl, only one of the match criteria must be true for a packet to belong to the class; multiple matching criteria are evaluated in a sequential order, with the highest precedence awarded to the first criterion defined for the class. An acl class type copies its set of match criteria from the current rule definition of the specified ACL number. |
| U32 agentDiffServClassAclNum | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.4 | Unsigned32 | read-create | The access list number used to define the match conditions for the DiffServ class. This attribute is only valid if the value of agentDiffServClassType is set to acl(3). Match conditions are copied from the ACL definition at the time the class is created and do not reflect subsequent changes to the ACL definition. |
| U32 agentDiffServClassRuleIndexNextFree | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.5 | Unsigned32 | read-only | This object contains an unused value for classRuleIndex, or a zero to indicate that none exists. This index is maintained on a per-class basis. |
| STO agentDiffServClassStorageType | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.6 | StorageType | read-create | Storage-type for this conceptual row |
| ROW agentDiffServClassRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.2.2.1.7 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServClassRuleTable | 1.3.6.1.4.1.4526.1.7.3.4.2.3 | not-accessible | A table of the DiffServ Class Rule entries | |
| agentDiffServClassRuleEntry | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1 | not-accessible | Represents entry for a set of class-match rules | |
| U32 agentDiffServClassRuleIndex | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.1 | Unsigned32 | not-accessible | The identifier for DiffServ Class Rule Table entry within a class |
| INT agentDiffServClassRuleMatchEntryType | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.2 | INTEGER | read-create | Class Rule match entry type, it determines which one of the individual match conditions is defined for the present class rule. This object must be created before any other match object in this row. |
| U32 agentDiffServClassRuleMatchCos | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.3 | Unsigned32 | read-create | Three-bit 802.1p priority field in the Ethernet frame used as a class-match parameter - only valid if the agentDiffServClassRuleMatchEntryType is set to cos(1). |
| IP agentDiffServClassRuleMatchDstIpAddr | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.4 | IpAddress | read-create | Destination IP address match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstip(2). |
| IP agentDiffServClassRuleMatchDstIpMask | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.5 | IpAddress | read-create | Destination IP address mask match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstip(2). This mask value identifies the portion of agentDiffServClassRuleMatchDstIpAddr that is compared against a packet. A non-contiguous mask value is permitted. |
| INE agentDiffServClassRuleMatchDstL4PortStart | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.6 | InetPortNumber | read-create | Destination layer 4 port range start match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstl4port(3). |
| INE agentDiffServClassRuleMatchDstL4PortEnd | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.7 | InetPortNumber | read-create | Destination layer 4 port range end match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstl4port(3). |
| MAC agentDiffServClassRuleMatchDstMacAddr | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.8 | MacAddress | read-create | Destination MAC address match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstmac(4). |
| MAC agentDiffServClassRuleMatchDstMacMask | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.9 | MacAddress | read-create | Destination MAC address mask match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to dstmac(4). This mask value identifies the portion of agentDiffServClassRuleMatchDstMacAddr that is compared against a packet. A non-contiguous mask value is permitted. |
| T/F agentDiffServClassRuleMatchEvery | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.10 | TruthValue | read-only | Flag to indicate that the class rule is defined to match on every packet, regardless of content. - only valid if the agentDiffServClassRuleMatchEntryType is set to every(5). |
| U32 agentDiffServClassRuleMatchIpDscp | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.11 | Unsigned32 | read-create | IP DiffServ Code Point (DSCP) match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to ipdscp(6). The DSCP is defined as the high-order six bits of the Service Type octet in the IPv4 header. |
| U32 agentDiffServClassRuleMatchIpPrecedence | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.12 | Unsigned32 | read-create | IP Precedence match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to ipprecedence(7). The Precedence bits are defined as the high-order three bits of the Service Type octed in the IPv4 header. |
| OCT agentDiffServClassRuleMatchIpTosBits | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.13 | OCTET STRING | read-create | IP TOS bits match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to iptos(8). The TOS bits are defined as all eight bits of the Service Type octet in the IPv4 header. |
| OCT agentDiffServClassRuleMatchIpTosMask | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.14 | OCTET STRING | read-create | IP TOS bits mask match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to iptos(8). This mask value identifies the portion of agentDiffServClassRuleMatchIpTosBits that is compared against a packet. A non-contiguous mask value is permitted. |
| U32 agentDiffServClassRuleMatchProtocolNum | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.15 | Unsigned32 | read-create | Protocol number match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to protocol(9). |
| U32 agentDiffServClassRuleMatchRefClassIndex | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.16 | Unsigned32 | read-create | Index of the corresponding referenced class - only valid if the agentDiffServClassRuleMatchEntryType is set to refclass(10). The set of match conditions defined for the reference class are directly inherited by the current class. Restrictions: 1) The class types of both, current class and the reference class must be identical (i.e., any vs. any, or all vs. all). 2) Self-referencing of class-name is not allowed. 3) Any attempt to delete the reference class while still referenced by any class shall fail. 4) The combined match criteria of classname and reference class name must be an allowed combination based on the class type. Any subsequent changes to the reference class name match criteria must maintain this validity, or the change attempt shall fail. |
| IP agentDiffServClassRuleMatchSrcIpAddr | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.17 | IpAddress | read-create | Source IP address match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcip(11). |
| IP agentDiffServClassRuleMatchSrcIpMask | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.18 | IpAddress | read-create | Source IP address mask match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcip(11). This mask value identifies the portion of agentDiffServClassRuleMatchSrcIpAddr that is compared against a packet. A non-contiguous mask value is permitted. |
| INE agentDiffServClassRuleMatchSrcL4PortStart | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.19 | InetPortNumber | read-create | Source layer 4 port range start match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcl4port(12). |
| INE agentDiffServClassRuleMatchSrcL4PortEnd | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.20 | InetPortNumber | read-create | Source layer 4 port range end match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcl4port(12). |
| MAC agentDiffServClassRuleMatchSrcMacAddr | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.21 | MacAddress | read-create | Source MAC address match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcmac(13). |
| MAC agentDiffServClassRuleMatchSrcMacMask | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.22 | MacAddress | read-create | Source MAC address mask match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to srcmac(13). This mask value identifies the portion of agentDiffServClassRuleMatchSrcMacAddr that is compared against a packet. A non-contiguous mask value is permitted. |
| U32 agentDiffServClassRuleMatchVlanId | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.23 | Unsigned32 | read-create | VLAN ID match value for the class - only valid if the agentDiffServClassRuleMatchEntryType is set to vlan(14). |
| T/F agentDiffServClassRuleMatchExcludeFlag | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.24 | TruthValue | read-create | Class Rule exclude flag - when set to true(1), the match condition identified by agentDiffServClassRuleMatchEntryType is negated. This means that for a given field, every value is considered to be a match EXCEPT for the value specified in the class rule. This flag must be false(2) for an agendDiffServClassRuleMatchEntryType of refClass(10). This object must be set after the agentDiffServClassRuleMatchEntryType object, but before any other match object in this row |
| STO agentDiffServClassRuleStorageType | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.25 | StorageType | read-create | Storage-type for this conceptual row |
| ROW agentDiffServClassRuleRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.2.3.1.26 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServPolicyGroup | 1.3.6.1.4.1.4526.1.7.3.4.3 | |||
| U32 agentDiffServPolicyIndexNextFree | 1.3.6.1.4.1.4526.1.7.3.4.3.1 | Unsigned32 | read-only | This object contains an unused value for agentDiffServPolicyIndex, or a zero to indicate that none exists. |
| agentDiffServPolicyTable | 1.3.6.1.4.1.4526.1.7.3.4.3.2 | not-accessible | A table of the DiffServ policy entries. | |
| agentDiffServPolicyEntry | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1 | not-accessible | Represents entry for a DiffServ policy. | |
| U32 agentDiffServPolicyIndex | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.1 | Unsigned32 | not-accessible | The identifier for DiffServ Policy table entry. |
| STR agentDiffServPolicyName | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.2 | DisplayString | read-create | Name of the policy |
| NUM agentDiffServPolicyType | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.3 | IntfDirection | read-create | The policy type dictates whether inbound or outbound policy attribute statements are used in the policy definition. |
| U32 agentDiffServPolicyInstIndexNextFree | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.4 | Unsigned32 | read-only | This object contains an unused value for agentDiffServPolicyInstIndex, or a zero to indicate that none exists. This index is maintained on a per-policy basis. |
| STO agentDiffServPolicyStorageType | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.5 | StorageType | read-create | Storage-type for this conceptual row |
| ROW agentDiffServPolicyRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.3.2.1.6 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServPolicyInstTable | 1.3.6.1.4.1.4526.1.7.3.4.3.3 | not-accessible | A table of the policy-class instance entries. | |
| agentDiffServPolicyInstEntry | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1 | not-accessible | Represents entry for a policy-class instance. | |
| U32 agentDiffServPolicyInstIndex | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1.1 | Unsigned32 | not-accessible | The identifier for policy-class Instance table entry within a policy. |
| U32 agentDiffServPolicyInstClassIndex | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1.2 | Unsigned32 | read-create | Index of the DiffServ Class Table row, whose class definition is used as the policy class instance. The class index identifies the classifier definition used by the policy to establish an instance of that class (to which policy attributes can be attached). This is what connects a class (instance) to a policy. |
| U32 agentDiffServPolicyInstAttrIndexNextFree | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1.3 | Unsigned32 | read-only | This object contains an unused value for agentDiffServPolicyAttrIndex, or a zero to indicate that none exists. This index is maintained on a per-policy-class-instance basis. |
| STO agentDiffServPolicyInstStorageType | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1.4 | StorageType | read-create | Storage-type for this conceptual row. |
| ROW agentDiffServPolicyInstRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.3.3.1.5 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServPolicyAttrTable | 1.3.6.1.4.1.4526.1.7.3.4.3.4 | not-accessible | A table of policy attribute entries | |
| agentDiffServPolicyAttrEntry | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1 | not-accessible | Represents entry for policy attributes | |
| U32 agentDiffServPolicyAttrIndex | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.1 | Unsigned32 | not-accessible | The identifier for policy-attribute entry |
| INT agentDiffServPolicyAttrStmtEntryType | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.2 | INTEGER | read-create | Policy attribute statement entry type -- this entry type is essential to determine which of the individual object(s) is defined for this policy attribute statement. This object must be created before any other policy attribute statement object in the row. The markIpDscpVal(4), markIpPrecedenceVal(5), policeSimple(6), policeSinglerate(7) and policeTworate(8) values are only allowed for an agentDiffServPolicyType of in(1). The remaining values are only allowed for an agentDiffServPolicyType of out(2). |
| U32 agentDiffServPolicyAttrStmtBandwidthCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.3 | Unsigned32 | read-create | Bandwidth committed rate attribute statement value -- identifies the minimum amount of bandwidth to be reserved for the specified class instance within the policy. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to bandwidth(1). |
| INT agentDiffServPolicyAttrStmtBandwidthCrateUnits | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.4 | INTEGER | read-create | Bandwidth committed rate units attribute statement value -- this value determines the interpretation of the agentDiffServPolicyAttrStmtBandwidthCrate object as either kilobits-per-second or as a percentage of interface link speed. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to bandwidth(1). |
| U32 agentDiffServPolicyAttrStmtExpediteCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.5 | Unsigned32 | read-create | Expedited (bandwidth) committed rate attribute statement value -- it identifies the maximum guaranteed amount of bandwidth to be reserved for the specified class instance within the policy. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to expedite(2). |
| INT agentDiffServPolicyAttrStmtExpediteCrateUnits | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.6 | INTEGER | read-create | Expedited (bandwidth) committed rate units attribute statement value -- determines the interpretation of the agentDiffServPolicyAttrStmtExpediteCrate object as either kilobits-per-second or as a percentage of interface link speed. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to expedite(2). |
| QOS agentDiffServPolicyAttrStmtExpediteCburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.7 | QosBurstSize | read-create | Expedited (bandwidth) committed burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to expedite(2). |
| U32 agentDiffServPolicyAttrStmtMarkCosVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.8 | Unsigned32 | read-create | Three-bit 802.1p priority(CoS) value as part of the outbound policy for a class instance. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to markCosVal(3). |
| U32 agentDiffServPolicyAttrStmtMarkIpDscpVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.9 | Unsigned32 | read-create | Specified IP DSCP value to mark in all inbound packets belonging to the class-instance. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to markIpDscpVal(4). |
| U32 agentDiffServPolicyAttrStmtMarkIpPrecedenceVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.10 | Unsigned32 | read-create | Specified IP Precedence value to mark in all inbound packets belonging to the class-instance. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to markIpPrecedenceVal(5). |
| INT agentDiffServPolicyAttrStmtPoliceConformAct | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.11 | INTEGER | read-create | Policing conform action attribute statement value -- determines the action taken on conforming traffic for the policing style (simple,singlerate,tworate) currently configured for the specified class instance within the policy. The default conform action is send(3). This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSimple(6), policeSinglerate(7), or policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtPoliceConformVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.12 | Unsigned32 | read-create | Policing conform DSCP or IP Precedence value attribute statement value -- used to mark the DSCP or IP Precedence field of conforming packets when the conform action is markdscp(2) or markprec(3), respectively. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSimple(6), policeSinglerate(7), or policeTworate(8). |
| INT agentDiffServPolicyAttrStmtPoliceExceedAct | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.13 | INTEGER | read-create | Policing exceed action attribute statement value -- determines the action taken on excess traffic for the policing style (singlerate, tworate) currently configured for the specified class instance within the policy. The default exceed action is drop(1). This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSinglerate(7) or policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtPoliceExceedVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.14 | Unsigned32 | read-create | Policing exceed DSCP or IP Precedence value attribute statement value -- used to mark the DSCP or IP Precedence field of excess packets when the exceed action is markdscp(2) or markprec(3), respectively. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSinglerate(7) or policeTworate(8). |
| INT agentDiffServPolicyAttrStmtPoliceNonconformAct | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.15 | INTEGER | read-create | Policing non-conform action attribute statement value -- determines the action taken on nonconforming traffic for the policing style (simple, singlerate,tworate) currently configured for the specified class instance within the policy. The default non-conform action is drop(1). This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSimple(6), policeSinglerate(7), or policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtPoliceNonconformVal | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.16 | Unsigned32 | read-create | Policing non-conform DSCP or IP Precedence value attribute statement value -- used to mark the DSCP or IP Precedence field of nonconforming packets when the nonconform action is markdscp(2) or markprec(3), respectively. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is policeSimple(6), policeSinglerate(7), or policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtPoliceSimpleCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.17 | Unsigned32 | read-create | Simple policing committed rate attribute statement value, specified in kbps. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeSimple(6). |
| QOS agentDiffServPolicyAttrStmtPoliceSimpleCburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.18 | QosBurstSize | read-create | Simple policing committed burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeSimple(6). |
| U32 agentDiffServPolicyAttrStmtPoliceSinglerateCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.19 | Unsigned32 | read-create | Single-rate policing committed rate attribute statement value, specified in kbps. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeSinglerate(7). |
| QOS agentDiffServPolicyAttrStmtPoliceSinglerateCburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.20 | QosBurstSize | read-create | Single-rate policing committed burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeSinglerate(7). |
| QOS agentDiffServPolicyAttrStmtPoliceSinglerateEburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.21 | QosBurstSize | read-create | Single-rate policing excess burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeSinglerate(7). |
| U32 agentDiffServPolicyAttrStmtPoliceTworateCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.22 | Unsigned32 | read-create | Two-rate policing committed rate attribute statement value, specified in kbps. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeTworate(8). |
| QOS agentDiffServPolicyAttrStmtPoliceTworateCburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.23 | QosBurstSize | read-create | Two-rate policing committed burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtPoliceTworatePrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.24 | Unsigned32 | read-create | Two-rate policing peak rate attribute statement value, specified in kbps. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeTworate(8). |
| QOS agentDiffServPolicyAttrStmtPoliceTworatePburst | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.25 | QosBurstSize | read-create | Two-rate policing peak burst size attribute statement value, specified in Kbytes. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to policeTworate(8). |
| U32 agentDiffServPolicyAttrStmtRandomdropMinThresh | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.26 | Unsigned32 | read-create | Random drop minimum threshold attribute statement value -- the average queue depth minimum threshold in bytes used by the WRED algorithm. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to randomdrop(9). |
| U32 agentDiffServPolicyAttrStmtRandomdropMaxThresh | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.27 | Unsigned32 | read-create | Random drop maximum threshold attribute statement value -- the average queue depth maximum threshold in bytes used by the WRED algorithm. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to randomdrop(9). |
| U32 agentDiffServPolicyAttrStmtRandomdropMaxDropProb | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.28 | Unsigned32 | read-create | Random drop maximum drop probability attribute statement value -- the packet drop probability when the queue depth average reaches its maximum threshold. It is expressed as a percentage, and is an integer from 0 to 100. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to randomdrop(9). |
| U32 agentDiffServPolicyAttrStmtRandomdropSamplingRate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.29 | Unsigned32 | read-create | Random drop sampling rate attribute statement value -- the period at which the queue depth is sampled for computing an average, expressed in microseconds. This value is an integer from 0 to 1000000, with a default value of 0 (meaning per packet sampling). This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to randomdrop(9). |
| U32 agentDiffServPolicyAttrStmtRandomdropDecayExponent | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.30 | Unsigned32 | read-create | Random drop decay exponent attribute statement value -- determines how quickly the average queue length calculation decays over time, with a higher number causing a slower decay. This value is an integer from 0 to 16, with a default of 9. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to randomdrop(9). |
| U32 agentDiffServPolicyAttrStmtShapeAverageCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.31 | Unsigned32 | read-create | Average-rate shaping committed rate attribute statement value, specified in kbps -- used to establish average rate traffic shaping for the specified class , which limits transmissions for the class to the committed information rate, with any excess traffic delayed via queueing. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to shapeAverage(10). |
| U32 agentDiffServPolicyAttrStmtShapePeakCrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.32 | Unsigned32 | read-create | Peak-rate shaping committed rate attribute statement value, specified in kbps -- used to establish peak rate traffic shaping for the specified class , which allows transmissions for the class to exceed the committed information rate by sending excess traffic with the understanding that it could be dropped by a downstream network element. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to shapePeak(11). |
| U32 agentDiffServPolicyAttrStmtShapePeakPrate | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.33 | Unsigned32 | read-create | Peak-rate shaping peak rate attribute statement value, specified in kbps -- used to establish peak rate traffic shaping for the specified class, which allows transmissions for the class to exceed the committed information rate by sending excess traffic with the understanding that it could be dropped by a downstream network element. This attribute is only valid if the value of agentDiffServPolicyAttrStmtEntryType is set to shapePeak(11). |
| STO agentDiffServPolicyAttrStorageType | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.34 | StorageType | read-create | Storage-type for this conceptual row. |
| ROW agentDiffServPolicyAttrRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.3.4.1.35 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServPolicyPerfInTable | 1.3.6.1.4.1.4526.1.7.3.4.3.5 | not-accessible | A table of inbound policy-class performance entries | |
| agentDiffServPolicyPerfInEntry | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1 | not-accessible | Represents entry for the performance attributes of the associated inbound policy-class instance | |
| C32 agentDiffServPolicyPerfInOfferedOctetsEx | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.1 | Counter32 | read-only | Offered octets count for the inbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfInOfferedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.2 | Counter32 | read-only | Offered packets count for the inbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfInDiscardedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.3 | Counter32 | read-only | Discarded octets count for the inbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfInDiscardedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.4 | Counter32 | read-only | Discarded packets count for the inbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfInHCOfferedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.5 | Counter64 | read-only | Offered octets high capacity count for the inbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfInHCOfferedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.6 | Counter64 | read-only | Offered packets high capacity count for the inbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfInHCDiscardedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.7 | Counter64 | read-only | Discarded octets high capacity count for the inbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfInHCDiscardedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.8 | Counter64 | read-only | Discarded packets high capacity count for the inbound policy-class instance performance entry. |
| STO agentDiffServPolicyPerfInStorageType | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.9 | StorageType | read-only | Storage-type for this conceptual row. |
| ROW agentDiffServPolicyPerfInRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.3.5.1.10 | RowStatus | read-only | The status of this conceptual row. |
| agentDiffServPolicyPerfOutTable | 1.3.6.1.4.1.4526.1.7.3.4.3.6 | not-accessible | A table of outbound policy-class performance entries | |
| agentDiffServPolicyPerfOutEntry | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1 | not-accessible | Represents entry for the performance attributes of the associated outbound policy-class instance | |
| C32 agentDiffServPolicyPerfOutTailDroppedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.1 | Counter32 | read-only | Tail-dropped octets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutTailDroppedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.2 | Counter32 | read-only | Tail-dropped packets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutRandomDroppedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.3 | Counter32 | read-only | Random-dropped octets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutRandomDroppedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.4 | Counter32 | read-only | Random-dropped packets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutShapeDelayedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.5 | Counter32 | read-only | Shape-delayed octets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutShapeDelayedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.6 | Counter32 | read-only | Shape-delayed packets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutSentOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.7 | Counter32 | read-only | Sent octets count for the outbound policy-class instance performance entry. |
| C32 agentDiffServPolicyPerfOutSentPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.8 | Counter32 | read-only | Sent packets count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCTailDroppedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.9 | Counter64 | read-only | Tail-dropped octets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCTailDroppedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.10 | Counter64 | read-only | Tail-dropped packets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCRandomDroppedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.11 | Counter64 | read-only | Random-dropped octets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCRandomDroppedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.12 | Counter64 | read-only | Random-dropped packets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCShapeDelayedOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.13 | Counter64 | read-only | Shape-delayed octets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCShapeDelayedPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.14 | Counter64 | read-only | Shape-delayed packets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCSentOctets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.15 | Counter64 | read-only | Sent octets high capacity count for the outbound policy-class instance performance entry. |
| C64 agentDiffServPolicyPerfOutHCSentPackets | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.16 | Counter64 | read-only | Sent packets high capacity count for the outbound policy-class instance performance entry. |
| STO agentDiffServPolicyPerfOutStorageType | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.17 | StorageType | read-only | Storage-type for this conceptual row. |
| ROW agentDiffServPolicyPerfOutRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.3.6.1.18 | RowStatus | read-only | The status of this conceptual row. |
| agentDiffServServiceGroup | 1.3.6.1.4.1.4526.1.7.3.4.4 | |||
| agentDiffServServiceTable | 1.3.6.1.4.1.4526.1.7.3.4.4.1 | not-accessible | A table of the service entries. | |
| agentDiffServServiceEntry | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1 | not-accessible | Represents entry for policy assigned to an interface in a particular direction. | |
| NUM agentDiffServServiceIfIndex | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.1 | InterfaceIndex | not-accessible | External interface number of the interface to which policy is assigned. |
| NUM agentDiffServServiceIfDirection | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.2 | IntfDirection | not-accessible | Interface direction to which the policy is assigned. |
| U32 agentDiffServServicePolicyIndex | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.3 | Unsigned32 | read-create | Index of the Policy Table row whose policy definition is attached to the interface in the specified direction. |
| INT agentDiffServServiceIfOperStatus | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.4 | INTEGER | read-only | The current operational state of the DiffServ service interface. If agentDiffServGenStatusAdminMode is disable(2) then agentDiffServServiceIfOperStatus should be down(2). If agentDiffServServiceGenStatusAdminMode is changed to enable(1) then agentDiffServServiceIfOperStatus should change to up(1) if the service interface is ready to send and receive DiffServ traffic; it should remain in the down(2) state if the underlying interface hardware is not in a link up condition, if the policy definition represented by agentDiffServServicePolicyIndex is incompatible with the interface (e.g., requires more bandwidth than the current capacity of the interface), or if the policy definition is considered to be incomplete (e.g., one or more composite rows is not in the active(1) state). |
| STO agentDiffServServiceStorageType | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.5 | StorageType | read-create | Storage-type for this conceptual row |
| ROW agentDiffServServiceRowStatus | 1.3.6.1.4.1.4526.1.7.3.4.4.1.1.6 | RowStatus | read-create | The status of this conceptual row. |
| agentDiffServServicePerfTable | 1.3.6.1.4.1.4526.1.7.3.4.4.2 | not-accessible | A table of service performance entries. | |
| agentDiffServServicePerfEntry | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1 | not-accessible | Represents a service performance entry. | |
| C32 agentDiffServServicePerfOfferedOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.1 | Counter32 | read-only | Offered octets count for the specified service interface and direction |
| C32 agentDiffServServicePerfOfferedPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.2 | Counter32 | read-only | Offered packets count for specified service interface and direction |
| C32 agentDiffServServicePerfDiscardedOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.3 | Counter32 | read-only | Discarded octets count for the specified service interface and direction |
| C32 agentDiffServServicePerfDiscardedPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.4 | Counter32 | read-only | Discarded packets count for the specified service interface and direction |
| C32 agentDiffServServicePerfSentOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.5 | Counter32 | read-only | Sent octets count for the specified service interface and direction |
| C32 agentDiffServServicePerfSentPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.6 | Counter32 | read-only | Sent packets count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCOfferedOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.7 | Counter64 | read-only | Offered octets high capacity count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCOfferedPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.8 | Counter64 | read-only | Offered packets high capacity count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCDiscardedOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.9 | Counter64 | read-only | Discarded octets high capacity count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCDiscardedPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.10 | Counter64 | read-only | Discarded packets high capacity count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCSentOctets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.11 | Counter64 | read-only | Sent octets high capacity count for the specified service interface and direction |
| C64 agentDiffServServicePerfHCSentPackets | 1.3.6.1.4.1.4526.1.7.3.4.4.2.1.12 | Counter64 | read-only | Sent packets high capacity count for the specified service interface and direction |
RFC description
Quality of Service and DiffServ classification, policy, and performance monitoring for network traffic on GSM7324 switches.
Start monitoring Netgear GSM7324 managed switch (DiffServ QoS policy/performance) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.