Dell-DEVICEPARAMS-MIB

All MIBs › Dell-DEVICEPARAMS-MIB

Organization: Dell

Last Updated: 2007-01-02

Category: Domain: System Management, Vendor: Dell

Description: Manages device-level parameters including system settings and hardware configuration on Dell switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Dell-DEVICEPARAMS-MIB?

Dell-DEVICEPARAMS-MIB is a Dell (RND/Rednet-derived) private MIB providing general device-level parameters for Dell managed bridges/switches, covering bridge type, ARP aging, SNMP community management, and general error/alarm reporting. Its data categories span basic configuration (bridge type, ARP timeout), security/access (community strings and access levels), and fault indication (bridge alarm and error description/severity). It supports monitoring hardware and software status via rndBrgVersion/rndBrgFeatures/rndBrgLicense (software/feature version), rndErrorDesc/rndErrorSeverity (fault detail), and rndBridgeAlarm (general alarm condition). It is a vendor-private extension layered on standard bridge MIB concepts rather than replacing them. Deployment context is Dell (Rednet-lineage) managed Ethernet switches/bridges in enterprise LAN environments, where administrators include Dell-DEVICEPARAMS-MIB SNMP monitoring in their standard bridge health-check templates alongside the base bridge MIB.

IPNetwork Monitor allows you to monitor SNMP objects defined in Dell-DEVICEPARAMS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dell PowerSwitch Z9964F-ON (2025) — 102.4 Tb/s AI-fabric switch, part of Dell's current PowerSwitch lineup that succeeded earlier Dell managed switches

Monitoring Examples

An admin would read rndBrgVersion and rndBrgFeatures to confirm firmware capabilities and licensing (rndBrgLicense) after a bridge upgrade, and monitor rndBridgeAlarm to catch general device fault conditions. Polling rndErrorDesc/rndErrorSeverity would surface the most recent error text and its severity for troubleshooting. rndCommunityTable/rndCommunityEntry (with rndCommunityMngStationAddr, rndCommunityString, rndCommunityAccess) would be audited to ensure only authorized management stations have read/write SNMP access.

What Can Be Monitored

bridge alarm/fault status
error description and severity
firmware version and licensed features
ARP inactivity timeout
SNMP community access configuration

Imported Objects

From Dell-MIB

rnd	MODULE-IDENTITY

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
PhysAddress
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
genGroup	1.3.6.1.4.1.89.2.11
STR genGroupConfigurationSymbol	1.3.6.1.4.1.89.2.11.2	DisplayString	read-only	Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version.
INT genGroupHWStatus	1.3.6.1.4.1.89.2.11.3	INTEGER	read-only	This attribute describes the status of the group hardware as detected by the sensors software.
STR genGroupHWVersion	1.3.6.1.4.1.89.2.11.1	DisplayString	read-only	Defines the HW version of the product.
STR rlComponentsInfoBaseline	1.3.6.1.4.1.89.2.16.2.1.5	DisplayString	read-only	Indicates the version control baseline of the SW component name.
STR rlComponentsInfoComponent	1.3.6.1.4.1.89.2.16.2.1.3	DisplayString	not-accessible	Indicates the SW component name.
rlComponentsInfoEntry	1.3.6.1.4.1.89.2.16.2.1		not-accessible	An entry in the rlComponentsInfoTable.
RLI rlComponentsInfoImageId	1.3.6.1.4.1.89.2.16.2.1.2	RlImageIdType	not-accessible	Indicates the image id in the unit
INT rlComponentsInfoStackUnitNumber	1.3.6.1.4.1.89.2.16.2.1.1	INTEGER	not-accessible	The unit number (for stackable devices) or 1 for 'stand alone' device.
rlComponentsInfoTable	1.3.6.1.4.1.89.2.16.2		not-accessible	The table contains information about components, their streams and baselines in the device images.
INT rlManagedMrid	1.3.6.1.4.1.89.2.7.3.1.2	INTEGER	read-write	The router instance currently managed by the NMS who accessed the agent through the community table entry corresponding to the keys of this entry
INT rlMridConnection	1.3.6.1.4.1.89.2.7.3.1.1	INTEGER	read-write	The router instance connecting the NMS who accessed the agent through the community table entry corresponding to the keys of this entry.
rlMridEntry	1.3.6.1.4.1.89.2.7.3.1		not-accessible	The row definition for this table.
rlMridTable	1.3.6.1.4.1.89.2.7.3		not-accessible	The MRID related configurations table of the agent
BIT rlResetStatus	1.3.6.1.4.1.89.2.13.2	Bits	read-only	A bit mask that specifies system status before reset action is preformed. Reset is prohibited in stackable products if the images selected after reboot are not of the same release version in ALL stack units. Downgrade status specifies that there are some actions to be preformed on the CDB file before reset is preformed. 0x0 - OK 0x1 - noStackIntegrity 0x2 - downgrade
RLI rndActiveSoftwareFile	1.3.6.1.4.1.89.2.13.1.1.2	RlImageIdType	read-only	Indicates the current active software file, image1 or image2.
INT rndActiveSoftwareFileAfterReset	1.3.6.1.4.1.89.2.13.1.1.3	INTEGER	read-write	Indicates the software file that will be active after reset (image1 or image2). If an error occurred in the download process, resulting in the corruption of the single software file, The value 'invalidImage' will be returned. This value can not be set by the user.
rndActiveSoftwareFileEntry	1.3.6.1.4.1.89.2.13.1.1		not-accessible	An entry (conceptual row) in the rndActiveSoftwareFileTable.
rndActiveSoftwareFileTable	1.3.6.1.4.1.89.2.13.1		not-accessible	The (conceptual) table listing the active software file of the requested unit.
T/F rndBackupConfigurationEnabled	1.3.6.1.4.1.89.2.15	TruthValue	read-only	Specifies whether the device supports backup-config parameters in lcli commands.
STR rndBaseBootVersion	1.3.6.1.4.1.89.2.10	DisplayString	read-only	Defines the boot version of the product.
PHY rndBasePhysicalAddress	1.3.6.1.4.1.89.2.12	PhysAddress	read-only	The Base physical (MAC) address of the device.
OCT rndBrgFeatures	1.3.6.1.4.1.89.2.5	OCTET STRING	read-only	A bit mask that defines the features supported by a particular configuration of this network element: __________________________________________ \| Byte 1\|Byte 2 \|Byte 3 \| ....\|Byte 20 \| \|87654321\| \| 87654321\| \|________\|_______________________________\| Byte1 : bit1: TX Block mask bit2: Source Routing Encapulation bit3: SNA/SDLC bit4: Frame Relay bit5: SNMP bit6: LAN Manager bit7: High Performance bit8: Translation Byte2 : bit1: DEC Router bit2: IPX Router bit3: IP Router Byte3 : bit1: Dial Up Backup bit2: COD bit3: FACS bit4: Load Balance bit5: Remote Configuration bit6: RIP 2 bit7: OSPF bit8: IPX RIP/SAP Filter Byte4 : bit1: BootP Server bit2: BootP Client bit3: Compression bit4: V25.bis bit5: ISDN bit6: CODv2 bit7: NSPF bit8: UDP Relay Byte5 bit1:VirtualLAN bit2:Static IP Multicast bit3:IP Redundancy bit4:CCM2 bit5:ISDN Bonding bit6:Backup Link Selection -- for the VAN/Rdapter ver 4.0 bit7:IP/IPX Forwarding -- for the WANgate ver 4.0 bit8:Improved COD Byte6 bit1: Server Disptacher bit2: ISDN_US -- for the VANSX/WANGATE ver 5.0 bit3: PPP bit4: IP Rip Filter -- for Vgate3 bit5: Zero Hop Routing -- for Vgate3 bit6: ISDN Japan bit7: PPP-Security Byte7 bit1: With unmanaged Switch bit2: 2 LANs bit3: OSPF Ver 2.0 bit4: FACS Ver 2.0 bit5: Multiple WEB Farm bit6: Backup Server bit7: Check Connectivity bit8: WSD multiplexing Byte8 bit1: MRT3 bit2: WSD Redundancy bit3: DHCP Server bit4: WSD Connection Limit bit5: WSD Distributed System bit6: WSD Load Report bit7: WSD super farm bit8: RadWiz leased line Byte9 bit1: PPP IP address negotiaton bit2: DNS bit3: Nat bit4: WSD Static proximity bit5: WSD Dynamic proximity bit6: WSD Proxy bit7: WSD Proximity client bit8: MAC Load balancing Byte10 bit1: Unnum Inf bit2: Power Supply redundancy bit3: MRT PPP Compression bit4: ZHR Apolo bit5: Copy port bit6: UDP Relay 2.0 bit7: NVRAM bit8: URL table Byte11 bit1: URL super farm bit2: NAT on LAN bit3: Remote Con bit4: AP5000 bit5: Session tracking bit6: Mirroring bit7: Alias IP bit8: CSD Nat Byte12 bit1: content check bit2: mlb virtual ip bit3: reserved Dell bit4: csd nat exception bit5: statistics monitor bit6: reserved-for-radware
OCT rndBrgLicense	1.3.6.1.4.1.89.2.6	OCTET STRING	read-write	This parameter is used for entering a s/w license number for a device. A separate license number is supplied for each device.
STR rndBrgVersion	1.3.6.1.4.1.89.2.4	DisplayString	read-only	The bridge version.
rndBridgeAlarm	1.3.6.1.4.1.89.2.3
INT rndBridgeType	1.3.6.1.4.1.89.2.1	INTEGER	read-only	Identification of the RND bridge type.
INT rndCommunityAccess	1.3.6.1.4.1.89.2.7.2.1.3	INTEGER	read-create	The allowed access to this management station
rndCommunityEntry	1.3.6.1.4.1.89.2.7.2.1		not-accessible	The row definition for this table.
IP rndCommunityMngStationAddr	1.3.6.1.4.1.89.2.7.2.1.1	IpAddress	read-create	The management station that will be allowed to communicate with the agent IP address
STR rndCommunityOwner	1.3.6.1.4.1.89.2.7.2.1.7	DisplayString	read-create	The owner of this community
INT rndCommunityPortSecurity	1.3.6.1.4.1.89.2.7.2.1.6	INTEGER	read-create	If enabled the device will only receive SNMP messages from the port, through which this NMS is reachable from the device.
INT rndCommunityStatus	1.3.6.1.4.1.89.2.7.2.1.5	INTEGER	read-create	The status of this entry. If the status is invalid the community entry will be deleted
STR rndCommunityString	1.3.6.1.4.1.89.2.7.2.1.2	DisplayString	read-create	The community string with which the management station will communicate with the agent
rndCommunityTable	1.3.6.1.4.1.89.2.7.2		not-accessible	The community table of the agent
INT rndCommunityTrapDestPort	1.3.6.1.4.1.89.2.7.2.1.8	INTEGER	read-create	The transport protocol (usually UDP) port to which traps to the management station represebted by this entry will be sent. The default is the well-known IANA assigned port number for SNMP traps. This object is relevant only if rndCommunityTrapsEnable has a value different from trapsDisable.
INT rndCommunityTrapsEnable	1.3.6.1.4.1.89.2.7.2.1.4	INTEGER	read-create	Should the agent send traps to the management station, and what version is required
rndDeviceParams	1.3.6.1.4.1.89.2			This private MIB module defines general Parameters private MIBs.
STR rndErrorDesc	1.3.6.1.4.1.89.2.3.1	DisplayString	read-only	A textual description of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
INT rndErrorSeverity	1.3.6.1.4.1.89.2.3.2	INTEGER	read-only	The severity type of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
STR rndImage1Date	1.3.6.1.4.1.89.2.16.1.1.6	DisplayString	read-only	Indicates the compilation date of image-1 in the system.
STR rndImage1Description	1.3.6.1.4.1.89.2.16.1.1.10	DisplayString	read-write	Indicates the description of image-1 in the system.
STR rndImage1Name	1.3.6.1.4.1.89.2.16.1.1.2	DisplayString	read-only	Indicates the file name of image-1 in the system.
STR rndImage1Time	1.3.6.1.4.1.89.2.16.1.1.8	DisplayString	read-only	Indicates the compilation time of image-1 in the system.
STR rndImage1Version	1.3.6.1.4.1.89.2.16.1.1.4	DisplayString	read-only	Indicates the version of image-1 in the system.
STR rndImage2Date	1.3.6.1.4.1.89.2.16.1.1.7	DisplayString	read-only	Indicates the compilation date of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Description	1.3.6.1.4.1.89.2.16.1.1.11	DisplayString	read-write	Indicates the description of image-2 in the system.
STR rndImage2Name	1.3.6.1.4.1.89.2.16.1.1.3	DisplayString	read-only	Indicates the file name of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Time	1.3.6.1.4.1.89.2.16.1.1.9	DisplayString	read-only	Indicates the compilation time of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Version	1.3.6.1.4.1.89.2.16.1.1.5	DisplayString	read-only	Indicates the version of image-2 (if present) in the system.If image-2 is not present show 'no info' text
rndImageInfo	1.3.6.1.4.1.89.2.16
rndImageInfoEntry	1.3.6.1.4.1.89.2.16.1.1		not-accessible	An entry in the rndImageInfoTable.
rndImageInfoTable	1.3.6.1.4.1.89.2.16.1		not-accessible	The table contains information about images.
INT rndImageSize	1.3.6.1.4.1.89.2.14	INTEGER	read-only	Max number of sectors currently allocated for image(s).
INT rndInactiveArpTimeOut	1.3.6.1.4.1.89.2.2	INTEGER	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
rndIpHost	1.3.6.1.4.1.89.2.7
rndIpHostManagement	1.3.6.1.4.1.89.2.7.4
INT rndIpHostManagementIfIndex	1.3.6.1.4.1.89.2.7.4.2	INTEGER	read-write	if supported manage , indicate ifindex, if 0 thaen disable
T/F rndIpHostManagementSupported	1.3.6.1.4.1.89.2.7.4.1	TruthValue	read-only	ifindex manage supported.
STR rndManagedDate	1.3.6.1.4.1.89.2.9	DisplayString	read-write	The date will be sent in the format ddmmyy
STR rndManagedTime	1.3.6.1.4.1.89.2.8	DisplayString	read-write	The time will be sent in the format hhmmss
rndSoftwareFile	1.3.6.1.4.1.89.2.13
INT rndStackUnitNumber	1.3.6.1.4.1.89.2.16.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.
INT rndUnitNumber	1.3.6.1.4.1.89.2.13.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.

RFC description

Dell device parameters and configuration management MIB (vendor-private).

Start monitoring Dell PowerConnect/Networking managed switch (general device parameters/bridge alarm) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Dell-DEVICEPARAMS-MIB

What Is Dell-DEVICEPARAMS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description