DLINK-3100-TRAPS-MIB

All MIBs › DLINK-3100-TRAPS-MIB

Category: Vendor: D-Link

Description: Defines SNMP trap and notification definitions for fault and event reporting on D-Link 3100 series switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINK-3100-TRAPS-MIB?

This is a D-Link proprietary MIB module for the D-Link 3100 series switches that defines the set of SNMP traps/notifications the device can send, rather than any polled data objects. It belongs to the fault-management category, giving an NMS a standardized way to receive asynchronous alerts for events such as link state changes, configuration changes, security violations, or hardware faults on the switch. Because it carries no readable data objects of its own, its monitoring value comes entirely from trap reception; it is the channel through which hardware/software status changes (link down, power/fan issues, unauthorized access attempts, etc., as defined by the specific traps) are pushed to a management station in near real time rather than discovered by polling. It commonly depends on SNMPv2-TC/SNMPv2-SMI notification conventions and complements other DLINK-3100 MIBs that hold the actual status objects referenced by these traps. It is deployed alongside an SNMP trap receiver/NMS so operators get immediate notification of fault or event conditions on 3100 series switches without waiting for a polling cycle. Engineers can download the DLINK-3100-TRAPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINK-3100-TRAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link 3100 series managed switch

Monitoring Examples

No sample objects were provided for this module and it defines NOTIFICATION-TYPE entries rather than readable MIB objects, so there is no polling-based monitoring scenario to describe; its purpose is limited to defining trap PDUs that the switch emits (e.g., for link, security, or configuration events) for an NMS to receive and log.

Imported Objects

From DLINK-3100-BRIDGEMIBOBJECTS-MIB

rldot1dStpTrapVrblVID	OBJECT-TYPE
rldot1dStpTrapVrblifIndex	OBJECT-TYPE

From DLINK-3100-DEVICEPARAMS-MIB

rndErrorDesc	OBJECT-TYPE
rndErrorSeverity	OBJECT-TYPE

From DLINK-3100-MIB

rndNotifications

OBJECT-IDENTITY

From SNMPv2-SMI

NOTIFICATION-TYPE

OIDs

OID symbolic	OID numeric	Description
NTF rxOverflowHWFault	1.3.6.1.4.1.171.10.94.89.89.0.3	An RX buffer overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number.
NTF txOverflowHWFault	1.3.6.1.4.1.171.10.94.89.89.0.4	Interport queue overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number.
NTF routeTableOverflow	1.3.6.1.4.1.171.10.94.89.89.0.5	An overflow condition has occurred in the Routing Table. The Routing Table is used for IP routing algorithm (RIP).
NTF resetRequired	1.3.6.1.4.1.171.10.94.89.89.0.10	This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable rndAction.
NTF endTftp	1.3.6.1.4.1.171.10.94.89.89.0.12	This trap indicates that in the device finished a TFTP transaction with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
NTF abortTftp	1.3.6.1.4.1.171.10.94.89.89.0.13	This trap indicates that in the device aborted a TFTP session with the management station. Variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
NTF startTftp	1.3.6.1.4.1.171.10.94.89.89.0.14	Informational trap indicating that the device has intiated a TFTP session. rndErrorDesc will contain the file type in question
NTF faultBackUp	1.3.6.1.4.1.171.10.94.89.89.0.23	Automantic switchover to backup link because of main link fault.
NTF mainLinkUp	1.3.6.1.4.1.171.10.94.89.89.0.24	Communication returened to main link.
NTF ipxRipTblOverflow	1.3.6.1.4.1.171.10.94.89.89.0.36	This trap indicates that in an OpenGate IPX RIP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
NTF ipxSapTblOverflow	1.3.6.1.4.1.171.10.94.89.89.0.37	This trap indicates that in an OpenGate IPX SAP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
NTF facsAccessVoilation	1.3.6.1.4.1.171.10.94.89.89.0.49	This trap indicates that message that fits FACS statenebt with operation blockAndReport was forward to the interface. The bound variable rndErrorDesc, rndErrorSeverity(== info ) and interface Number.
NTF autoConfigurationCompleted	1.3.6.1.4.1.171.10.94.89.89.0.50	This trap indicates that auto comfiguration completetd succssefully. The bound variable rndErrorDesc, rndErrorSeverity(== info )
NTF forwardingTabOverflow	1.3.6.1.4.1.171.10.94.89.89.0.51	This trap indicates that an overflow condition has occurred in the layer II Forward Table. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF framRelaySwitchConnectionUp	1.3.6.1.4.1.171.10.94.89.89.0.53	This trap indicates that a connection establish between the Frame relay Switch and the WanGate. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF framRelaySwitchConnectionDown	1.3.6.1.4.1.171.10.94.89.89.0.54	This trap indicates that a connection between the Frame Relay Switch and the WanGate failed. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF errorsDuringInit	1.3.6.1.4.1.171.10.94.89.89.0.61	This trap indicates that the an error occured during initialization The bound variable rndErrorDesc, rndErrorSeverity(== error )
NTF vlanDynPortAdded	1.3.6.1.4.1.171.10.94.89.89.0.66
NTF vlanDynPortRemoved	1.3.6.1.4.1.171.10.94.89.89.0.67
NTF rsSDclientsTableOverflow	1.3.6.1.4.1.171.10.94.89.89.0.68	This warning is generated when an overflow occurs in the clients table.
NTF rsSDinactiveServer	1.3.6.1.4.1.171.10.94.89.89.0.69	This warning is generated when a server does not respond to the dispatchers polling and is thought to be inactive.
NTF rsIpZhrConnectionsTableOverflow	1.3.6.1.4.1.171.10.94.89.89.0.70	The Zero Hop Routing connections Table has been overflown.
NTF rsIpZhrReqStaticConnNotAccepted	1.3.6.1.4.1.171.10.94.89.89.0.71	The requested static connection was not accepted because there is no available IP virtual address to allocate to it.
NTF rsIpZhrVirtualIpAsSource	1.3.6.1.4.1.171.10.94.89.89.0.72	The virtual IP address appeared as a source IP. All the connections using it will be deleted and it will not be further allocated to new connections.
NTF rsIpZhrNotAllocVirtualIp	1.3.6.1.4.1.171.10.94.89.89.0.73	The source IP address sent an ARP specifying a virtual IP which was not allocated for this source. This virtual IP will not be allocated to connections of this specific source IP.
NTF rsSnmpSetRequestInSpecialCfgState	1.3.6.1.4.1.171.10.94.89.89.0.74	An incoming SNMP SET request was rejected because no such requests (except action requests) are accepted after start of new configuration reception or during sending the current configuration to an NMS.
NTF rsPingCompletion	1.3.6.1.4.1.171.10.94.89.89.0.136	A rsPingCompleted trap is sent at the completion of a sequence of pings if such a trap was requested when the sequence was initiated. The trap severity is info. The trap text will specify the following information: rsPingCompletionStatus, rsPingSentPackets, rsPingReceivedPackets In addition to the above listed objects (which are always present), the message will also specify the following quantities: if any responses were received: rsPingMinReturnTime rsPingAvgReturnTime rsPingMaxReturnTime
NTF pppSecurityViolation	1.3.6.1.4.1.171.10.94.89.89.0.137	This trap indicates that a PPP link got an unrecognized secret. The bound variables rndErrorDesc, rndErrorSeverity(== warning ), interface Number. and pppSecurityIdentity
NTF frDLCIStatudChange	1.3.6.1.4.1.171.10.94.89.89.0.138
NTF papFailedCommunication	1.3.6.1.4.1.171.10.94.89.89.0.139
NTF chapFailedCommunication	1.3.6.1.4.1.171.10.94.89.89.0.140
NTF rsWSDRedundancySwitch	1.3.6.1.4.1.171.10.94.89.89.0.141	Whenever main server fails and backup takes over or server comes up after failure a trap of this type is issued.
NTF rsDhcpAllocationFailure	1.3.6.1.4.1.171.10.94.89.89.0.142	DHCP failed to allocate an IP address to a requesting host because of memory shortage or inadequate configuration of available IP addresses.
NTF rlIpFftStnOverflow	1.3.6.1.4.1.171.10.94.89.89.0.145	The IP SFFT overflow.
NTF rlIpFftSubOverflow	1.3.6.1.4.1.171.10.94.89.89.0.146	The IP NFFT overflow.
NTF rlIpxFftStnOverflow	1.3.6.1.4.1.171.10.94.89.89.0.147	The IPX SFFT overflow.
NTF rlIpxFftSubOverflow	1.3.6.1.4.1.171.10.94.89.89.0.148	The IPX NFFT overflow.
NTF rlIpmFftOverflow	1.3.6.1.4.1.171.10.94.89.89.0.149	The IPM FFT overflow.
NTF rlPhysicalDescriptionChanged	1.3.6.1.4.1.171.10.94.89.89.0.150	Indicates that the physical decription of the device has changed
NTF rldot1dStpPortStateForwarding	1.3.6.1.4.1.171.10.94.89.89.0.151	The trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state.
NTF rldot1dStpPortStateNotForwarding	1.3.6.1.4.1.171.10.94.89.89.0.152	The trap is sent by a bridge when any of its configured ports transitions from the Forwarding state to the Blocking state.
NTF rlPolicyDropPacketTrap	1.3.6.1.4.1.171.10.94.89.89.0.153	Indicates that the packet drop due to the policy
NTF rlPolicyForwardPacketTrap	1.3.6.1.4.1.171.10.94.89.89.0.154	Indicates that the packet has forward based on policy
NTF rlIgmpProxyTableOverflow	1.3.6.1.4.1.171.10.94.89.89.0.156	An IGMP PROXY Table overflow.
NTF rlIgmpV1MsgReceived	1.3.6.1.4.1.171.10.94.89.89.0.157	An IGMP Message of v1 received on ifIndex.
NTF rlVrrpEntriesDeleted	1.3.6.1.4.1.171.10.94.89.89.0.158	One or more VRRP entries deleted due to IP interface deletion or transition.
NTF rlHotSwapTrap	1.3.6.1.4.1.171.10.94.89.89.0.159	Hot swap trap.
NTF rlTrunkPortAddedTrap	1.3.6.1.4.1.171.10.94.89.89.0.160	Informational trap indicating that a port is added to a trunk
NTF rlTrunkPortRemovedTrap	1.3.6.1.4.1.171.10.94.89.89.0.161	This warning is generated when a port removed from a trunk.
NTF rlTrunkPortNotCapableTrap	1.3.6.1.4.1.171.10.94.89.89.0.162	Informational trap indicating that a port can not be added to a trunk because of device limitations or diffrent swIfType.
NTF rlLockPortTrap	1.3.6.1.4.1.171.10.94.89.89.0.170	Informational trap indicating that a locked port receive a frame with new source Mac Address.
NTF vlanDynVlanAdded	1.3.6.1.4.1.171.10.94.89.89.0.171	add gvrp dynamic vlan
NTF vlanDynVlanRemoved	1.3.6.1.4.1.171.10.94.89.89.0.172	remove gvrp dynamic vlan
NTF vlanDynamicToStatic	1.3.6.1.4.1.171.10.94.89.89.0.173	vlan status was changed from dynamic to static
NTF vlanStaticToDynamic	1.3.6.1.4.1.171.10.94.89.89.0.174	vlan status was changed from static to dynamic
NTF dstrSysLog	1.3.6.1.4.1.171.10.94.89.89.0.175	Master receive trap from slave , and forward it as trap
NTF rlEnvMonFanStateChange	1.3.6.1.4.1.171.10.94.89.89.0.176	Trap indicating the fan state. rndErrorSeverity will be: 0 for fan state nomal, notPresent 1 for fan state warning, notFunctioning 2 for fan state critical 3 for fan state fatal The error text will specify the fan index, fan description and the exact fan state
NTF rlEnvMonPowerSupplyStateChange	1.3.6.1.4.1.171.10.94.89.89.0.177	Trap indicating the power supply state. rndErrorSeverity will be: 0 for power supply state nomal, notPresent 1 for power supply state warning, notFunctioning 2 for power supply state critical 3 for power supply state fatal The error text will specify the power supply index, power supply description and the exact power supply state
NTF rlStackStateChange	1.3.6.1.4.1.171.10.94.89.89.0.178	Trap indicating the stack connection state 0 for stack state connected, 1 for stack state disconnected
NTF rlEnvMonTemperatureRisingAlarm	1.3.6.1.4.1.171.10.94.89.89.0.179	Trap indicating that the temperature in the device has exceeded the device specific safe temperature threshold.
NTF rlBrgMacAddFailedTrap	1.3.6.1.4.1.171.10.94.89.89.0.183	Informational trap indicating that adding dynamic mac/s failed due to full hash chain.
NTF rldot1xPortStatusAuthorizedTrap	1.3.6.1.4.1.171.10.94.89.89.0.184	Informational trap indicating that port 802.1x status is authorized.
NTF rldot1xPortStatusUnauthorizedTrap	1.3.6.1.4.1.171.10.94.89.89.0.185	Warning trap is indicating that port 802.1x status is unAuthorized.
NTF swIfTablePortLock	1.3.6.1.4.1.171.10.94.89.89.0.192	Warning trap is indicating port lock hase began.
NTF swIfTablePortUnLock	1.3.6.1.4.1.171.10.94.89.89.0.193	Warning trap is indicating port lock has ended.
NTF rlAAAUserLocked	1.3.6.1.4.1.171.10.94.89.89.0.194	Warning trap indicating that the user was locked after number of consecutives unsuccessful login attempts.
NTF bpduGuardPortSuspended	1.3.6.1.4.1.171.10.94.89.89.0.202	Warning trap indicating - Port was suspended because there was BPDU Guard violation.
NTF rldot1xSupplicantMacAuthorizedTrap	1.3.6.1.4.1.171.10.94.89.89.0.203	Informational trap indicating that MAC authentication supplicant is authenticated and is allowed to access the network.
NTF rldot1xSupplicantMacUnauthorizedTrap	1.3.6.1.4.1.171.10.94.89.89.0.204	Warning trap is indicating that Radius server rejects MAC authentication supplicant.
NTF stpLoopbackDetection	1.3.6.1.4.1.171.10.94.89.89.0.205	Warning trap indicating - A loopback was detected on port.
NTF stpLoopbackDetectionResolved	1.3.6.1.4.1.171.10.94.89.89.0.206	Warning trap indicating - A loopback detection resolved on port.
NTF loopbackDetectionPortSuspended	1.3.6.1.4.1.171.10.94.89.89.0.207	Warning trap indicating - A port has been suspended by Loopback Detection.
NTF rlSwStormControlSuspend	1.3.6.1.4.1.171.10.94.89.89.0.213	Warning trap indicating - Port was suspended because there was storm violation.

RFC description

D-Link 3100 switch private SNMP traps MIB providing enterprise-specific trap definitions for hardware faults and routing events.

Start monitoring D-Link 3100 series switch (DES/DGS-3100), SNMP trap/notification definitions with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINK-3100-TRAPS-MIB

What Is DLINK-3100-TRAPS-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description