DLINK-3100-DEVICEPARAMS-MIB

All MIBs › DLINK-3100-DEVICEPARAMS-MIB

Organization: Dlink, Inc. Dlink Semiconductor, Inc.

Last Updated: 2007-01-02

Category: Domain: System Management, Vendor: D-Link

Description: D-Link 3100 device parameters MIB providing objects for system-wide device configuration and parameter management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINK-3100-DEVICEPARAMS-MIB?

DLINK-3100-DEVICEPARAMS-MIB is a private MIB module for the D-Link DL-3100-series device (originating from RAD Network Devices, reflected in the 'rnd' object prefix, and OEM'd/rebranded by D-Link), covering general device-wide configuration parameters. It exposes bridge type and version/feature/license information, ARP timeout configuration, SNMP community-based access security, IP host management, and explicit error/alarm reporting objects. It is strongly oriented toward DLINK-3100-DEVICEPARAMS-MIB SNMP monitoring of hardware/software status: dedicated error-description and error-severity objects report the device's most recent internal fault, a bridge-alarm object flags an active alarm condition, and version/feature/license objects let an admin confirm which firmware and licensed capabilities are running. It parallels concepts from the standard bridging (BRIDGE-MIB) and SNMP community-security frameworks of that era, though implemented as a proprietary vendor extension rather than by direct dependency. It is deployed on D-Link DL-3100 bridge/router units used in WAN and leased-line bridging deployments.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINK-3100-DEVICEPARAMS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DL-3100 bridge/router (RAD Network Devices OEM)

Monitoring Examples

rndErrorDesc paired with rndErrorSeverity lets an admin see the device's most recent internal fault and its severity level, while rndBridgeAlarm reports an active bridge alarm condition; rndBrgVersion and rndBrgFeatures/rndBrgLicense reveal the running software version and which licensed features are enabled, and the rndCommunityTable (rndCommunityString, rndCommunityAccess, rndCommunityMngStationAddr) exposes configured SNMP community strings, access rights, and permitted management stations.

What Can Be Monitored

error code/severity reporting
bridge alarm status
software version/license features
SNMP community access configuration
ARP timeout setting

Imported Objects

From DLINK-3100-MIB

rnd	MODULE-IDENTITY

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
PhysAddress
TruthValue

How to Use in IPNetwork Monitor

Example using rndImageSize OID:

Select a D-Link DL-3100 bridge/router (RAD Network Devices OEM) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rndImageSize into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of flash sectors currently allocated for firmware image storage. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value approaches the flash device's total sector capacity, so you catch a full or nearly-full image partition before a firmware upgrade fails. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
genGroup	1.3.6.1.4.1.171.10.94.89.89.2.11
STR genGroupConfigurationSymbol	1.3.6.1.4.1.171.10.94.89.89.2.11.2	DisplayString	read-only	Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version.
INT genGroupHWStatus	1.3.6.1.4.1.171.10.94.89.89.2.11.3	INTEGER	read-only	This attribute describes the status of the group hardware as detected by the sensors software.
STR genGroupHWVersion	1.3.6.1.4.1.171.10.94.89.89.2.11.1	DisplayString	read-only	Defines the HW version of the product.
STR rlComponentsInfoBaseline	1.3.6.1.4.1.171.10.94.89.89.2.16.2.1.5	DisplayString	read-only	Indicates the version control baseline of the SW component name.
STR rlComponentsInfoComponent	1.3.6.1.4.1.171.10.94.89.89.2.16.2.1.3	DisplayString	not-accessible	Indicates the SW component name.
rlComponentsInfoEntry	1.3.6.1.4.1.171.10.94.89.89.2.16.2.1		not-accessible	An entry in the rlComponentsInfoTable.
RLI rlComponentsInfoImageId	1.3.6.1.4.1.171.10.94.89.89.2.16.2.1.2	RlImageIdType	not-accessible	Indicates the image id in the unit
INT rlComponentsInfoStackUnitNumber	1.3.6.1.4.1.171.10.94.89.89.2.16.2.1.1	INTEGER	not-accessible	The unit number (for stackable devices) or 1 for 'stand alone' device.
rlComponentsInfoTable	1.3.6.1.4.1.171.10.94.89.89.2.16.2		not-accessible	The table contains information about components, their streams and baselines in the device images.
INT rlManagedMrid	1.3.6.1.4.1.171.10.94.89.89.2.7.3.1.2	INTEGER	read-write	The router instance currently managed by the NMS who accessed the agent through the community table entry corresponding to the keys of this entry
INT rlMridConnection	1.3.6.1.4.1.171.10.94.89.89.2.7.3.1.1	INTEGER	read-write	The router instance connecting the NMS who accessed the agent through the community table entry corresponding to the keys of this entry.
rlMridEntry	1.3.6.1.4.1.171.10.94.89.89.2.7.3.1		not-accessible	The row definition for this table.
rlMridTable	1.3.6.1.4.1.171.10.94.89.89.2.7.3		not-accessible	The MRID related configurations table of the agent
BIT rlResetStatus	1.3.6.1.4.1.171.10.94.89.89.2.13.2	Bits	read-only	A bit mask that specifies system status before reset action is preformed. Reset is prohibited in stackable products if the images selected after reboot are not of the same release version in ALL stack units. Downgrade status specifies that there are some actions to be preformed on the CDB file before reset is preformed. 0x0 - OK 0x1 - noStackIntegrity 0x2 - downgrade
RLI rndActiveSoftwareFile	1.3.6.1.4.1.171.10.94.89.89.2.13.1.1.2	RlImageIdType	read-only	Indicates the current active software file, image1 or image2.
INT rndActiveSoftwareFileAfterReset	1.3.6.1.4.1.171.10.94.89.89.2.13.1.1.3	INTEGER	read-write	Indicates the software file that will be active after reset (image1 or image2). If an error occurred in the download process, resulting in the corruption of the single software file, The value 'invalidImage' will be returned. This value can not be set by the user.
rndActiveSoftwareFileEntry	1.3.6.1.4.1.171.10.94.89.89.2.13.1.1		not-accessible	An entry (conceptual row) in the rndActiveSoftwareFileTable.
rndActiveSoftwareFileTable	1.3.6.1.4.1.171.10.94.89.89.2.13.1		not-accessible	The (conceptual) table listing the active software file of the requested unit.
T/F rndBackupConfigurationEnabled	1.3.6.1.4.1.171.10.94.89.89.2.15	TruthValue	read-only	Specifies whether the device supports backup-config parameters in lcli commands.
STR rndBaseBootVersion	1.3.6.1.4.1.171.10.94.89.89.2.10	DisplayString	read-only	Defines the boot version of the product.
PHY rndBasePhysicalAddress	1.3.6.1.4.1.171.10.94.89.89.2.12	PhysAddress	read-only	The Base physical (MAC) address of the device.
OCT rndBrgFeatures	1.3.6.1.4.1.171.10.94.89.89.2.5	OCTET STRING	read-only	A bit mask that defines the features supported by a particular configuration of this network element: __________________________________________ \| Byte 1\|Byte 2 \|Byte 3 \| ....\|Byte 20 \| \|87654321\| \| 87654321\| \|________\|_______________________________\| Byte1 : bit1: TX Block mask bit2: Source Routing Encapulation bit3: SNA/SDLC bit4: Frame Relay bit5: SNMP bit6: LAN Manager bit7: High Performance bit8: Translation Byte2 : bit1: DEC Router bit2: IPX Router bit3: IP Router Byte3 : bit1: Dial Up Backup bit2: COD bit3: FACS bit4: Load Balance bit5: Remote Configuration bit6: RIP 2 bit7: OSPF bit8: IPX RIP/SAP Filter Byte4 : bit1: BootP Server bit2: BootP Client bit3: Compression bit4: V25.bis bit5: ISDN bit6: CODv2 bit7: NSPF bit8: UDP Relay Byte5 bit1:VirtualLAN bit2:Static IP Multicast bit3:IP Redundancy bit4:CCM2 bit5:ISDN Bonding bit6:Backup Link Selection -- for the VAN/Rdapter ver 4.0 bit7:IP/IPX Forwarding -- for the WANgate ver 4.0 bit8:Improved COD Byte6 bit1: Server Disptacher bit2: ISDN_US -- for the VANSX/WANGATE ver 5.0 bit3: PPP bit4: IP Rip Filter -- for Vgate3 bit5: Zero Hop Routing -- for Vgate3 bit6: ISDN Japan bit7: PPP-Security Byte7 bit1: With unmanaged Switch bit2: 2 LANs bit3: OSPF Ver 2.0 bit4: FACS Ver 2.0 bit5: Multiple WEB Farm bit6: Backup Server bit7: Check Connectivity bit8: WSD multiplexing Byte8 bit1: MRT3 bit2: WSD Redundancy bit3: DHCP Server bit4: WSD Connection Limit bit5: WSD Distributed System bit6: WSD Load Report bit7: WSD super farm bit8: RadWiz leased line Byte9 bit1: PPP IP address negotiaton bit2: DNS bit3: Nat bit4: WSD Static proximity bit5: WSD Dynamic proximity bit6: WSD Proxy bit7: WSD Proximity client bit8: MAC Load balancing Byte10 bit1: Unnum Inf bit2: Power Supply redundancy bit3: MRT PPP Compression bit4: ZHR Apolo bit5: Copy port bit6: UDP Relay 2.0 bit7: NVRAM bit8: URL table Byte11 bit1: URL super farm bit2: NAT on LAN bit3: Remote Con bit4: AP5000 bit5: Session tracking bit6: Mirroring bit7: Alias IP bit8: CSD Nat Byte12 bit1: content check bit2: mlb virtual ip bit3: reserved DLINK-3100 bit4: csd nat exception bit5: statistics monitor bit6: reserved-for-radware
OCT rndBrgLicense	1.3.6.1.4.1.171.10.94.89.89.2.6	OCTET STRING	read-write	This parameter is used for entering a s/w license number for a device. A separate license number is supplied for each device.
STR rndBrgVersion	1.3.6.1.4.1.171.10.94.89.89.2.4	DisplayString	read-only	The bridge version.
rndBridgeAlarm	1.3.6.1.4.1.171.10.94.89.89.2.3
INT rndBridgeType	1.3.6.1.4.1.171.10.94.89.89.2.1	INTEGER	read-only	Identification of the RND bridge type.
INT rndCommunityAccess	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.3	INTEGER	read-create	The allowed access to this management station
rndCommunityEntry	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1		not-accessible	The row definition for this table.
IP rndCommunityMngStationAddr	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.1	IpAddress	read-create	The management station that will be allowed to communicate with the agent IP address
STR rndCommunityOwner	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.7	DisplayString	read-create	The owner of this community
INT rndCommunityPortSecurity	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.6	INTEGER	read-create	If enabled the device will only receive SNMP messages from the port, through which this NMS is reachable from the device.
INT rndCommunityStatus	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.5	INTEGER	read-create	The status of this entry. If the status is invalid the community entry will be deleted
STR rndCommunityString	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.2	DisplayString	read-create	The community string with which the management station will communicate with the agent
rndCommunityTable	1.3.6.1.4.1.171.10.94.89.89.2.7.2		not-accessible	The community table of the agent
INT rndCommunityTrapDestPort	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.8	INTEGER	read-create	The transport protocol (usually UDP) port to which traps to the management station represebted by this entry will be sent. The default is the well-known IANA assigned port number for SNMP traps. This object is relevant only if rndCommunityTrapsEnable has a value different from trapsDisable.
INT rndCommunityTrapsEnable	1.3.6.1.4.1.171.10.94.89.89.2.7.2.1.4	INTEGER	read-create	Should the agent send traps to the management station, and what version is required
rndDeviceParams	1.3.6.1.4.1.171.10.94.89.89.2			This private MIB module defines general Parameters private MIBs.
STR rndErrorDesc	1.3.6.1.4.1.171.10.94.89.89.2.3.1	DisplayString	read-only	A textual description of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
INT rndErrorSeverity	1.3.6.1.4.1.171.10.94.89.89.2.3.2	INTEGER	read-only	The severity type of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
STR rndImage1Date	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.6	DisplayString	read-only	Indicates the compilation date of image-1 in the system.
STR rndImage1Name	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.2	DisplayString	read-only	Indicates the file name of image-1 in the system.
STR rndImage1Time	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.8	DisplayString	read-only	Indicates the compilation time of image-1 in the system.
STR rndImage1Version	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.4	DisplayString	read-only	Indicates the version of image-1 in the system.
STR rndImage2Date	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.7	DisplayString	read-only	Indicates the compilation date of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Name	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.3	DisplayString	read-only	Indicates the file name of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Time	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.9	DisplayString	read-only	Indicates the compilation time of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Version	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.5	DisplayString	read-only	Indicates the version of image-2 (if present) in the system.If image-2 is not present show 'no info' text
rndImageInfo	1.3.6.1.4.1.171.10.94.89.89.2.16
rndImageInfoEntry	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1		not-accessible	An entry in the rndImageInfoTable.
rndImageInfoTable	1.3.6.1.4.1.171.10.94.89.89.2.16.1		not-accessible	The table contains information about images.
INT rndImageSizeEx	1.3.6.1.4.1.171.10.94.89.89.2.14	INTEGER	read-only	Max number of sectors currently allocated for image(s).
INT rndInactiveArpTimeOut	1.3.6.1.4.1.171.10.94.89.89.2.2	INTEGER	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
rndIpHost	1.3.6.1.4.1.171.10.94.89.89.2.7
rndIpHostManagement	1.3.6.1.4.1.171.10.94.89.89.2.7.4
INT rndIpHostManagementIfIndex	1.3.6.1.4.1.171.10.94.89.89.2.7.4.2	INTEGER	read-write	if supported manage , indicate ifindex, if 0 thaen disable
T/F rndIpHostManagementSupported	1.3.6.1.4.1.171.10.94.89.89.2.7.4.1	TruthValue	read-only	ifindex manage supported.
STR rndManagedDate	1.3.6.1.4.1.171.10.94.89.89.2.9	DisplayString	read-write	The date will be sent in the format ddmmyy
STR rndManagedTime	1.3.6.1.4.1.171.10.94.89.89.2.8	DisplayString	read-write	The time will be sent in the format hhmmss
rndSoftwareFile	1.3.6.1.4.1.171.10.94.89.89.2.13
INT rndStackUnitNumber	1.3.6.1.4.1.171.10.94.89.89.2.16.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.
INT rndUnitNumber	1.3.6.1.4.1.171.10.94.89.89.2.13.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.

FAQ

What can DLINK-3100-DEVICEPARAMS-MIB tell you about a fault on a D-Link DL-3100 bridge?
It includes dedicated error-description and error-severity objects that report the device's most recent internal fault, plus a bridge-alarm object that flags an active alarm condition -- letting an operator see at a glance whether a DL-3100 unit currently has an outstanding hardware or software problem.

How would you confirm firmware/license status on a D-Link DL-3100 using this MIB?
The module exposes version, feature, and license objects, so polling them lets an administrator confirm which firmware version is running and which licensed capabilities are enabled on the bridge, alongside checking ARP timeout and SNMP community access settings for general configuration health.

RFC description

D-Link DGS-3100 Gigabit managed switch device parameters MIB for SNMP-based configuration and monitoring.

Start monitoring D-Link DL-3100 bridge/router (RAD Network Devices OEM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINK-3100-DEVICEPARAMS-MIB