DLINK-3100-STATISTICS-MIB

All MIBs › DLINK-3100-STATISTICS-MIB

Organization: Dlink, Inc.

Last Updated: 2020-07-11

Category: Technology: Traffic Monitoring, Vendor: D-Link

Description: Provides detailed traffic and error statistics counters for ports and interfaces on D-Link 3100 series switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINK-3100-STATISTICS-MIB?

DLINK-3100-STATISTICS-MIB is a D-Link vendor MIB providing detailed per-port and per-interface traffic and error statistics for the D-Link 3100 series of managed switches. It exposes counters for traffic volume (packets/octets in and out) and error conditions (CRC errors, collisions, discards) typical of switch statistics MIBs. Its monitoring focus is squarely on interface-level performance and fault counters — letting an operator spot a port with rising error rates, excessive collisions, or unusually high/low traffic that could indicate a failing cable, NIC, or a misbehaving connected device. It likely complements the standard IF-MIB/EtherLike-MIB counters with D-Link-specific extensions rather than replacing them. It is deployed in small-to-midsize enterprise networks using D-Link 3100 series switches, where administrators use SNMP polling to track port-level traffic and diagnose connectivity issues. Engineers can download the DLINK-3100-STATISTICS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINK-3100-STATISTICS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link 3100 series managed switches

Monitoring Examples

No object names were captured for this module, so specific OIDs cannot be cited; based on the short description, an admin would typically poll per-port traffic and error counters on the D-Link 3100 switch to detect a port with a rising CRC-error or collision rate, which would point to a bad cable or duplex mismatch.

What Can Be Monitored

per-port traffic packet/octet counters
per-port error counters
collision counts
discard counts

Imported Objects

From DLINK-3100-MIB

rnd	MODULE-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From RFC1155-SMI

Counter

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
rlStatistics	1.3.6.1.4.1.171.10.94.89.89.141			Dlink statistics MIBs
rlStatisticsPacketTable	1.3.6.1.4.1.171.10.94.89.89.141.1		read-only	Dlink Packet statistics MIB Table
rlStatisticsPacketEntry	1.3.6.1.4.1.171.10.94.89.89.141.1.1		read-only	Row definition for packet statistic table.
CTR rlStatisticsPacket64Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.1	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacket65to127Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.2	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacket128to255Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.3	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacket256to511Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.4	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacket512to1023Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.5	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacket1024to1518Octets	1.3.6.1.4.1.171.10.94.89.89.141.1.1.6	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacketOversizePkts	1.3.6.1.4.1.171.10.94.89.89.141.1.1.7	Counter	read-only	Amount of packets per size
CTR rlStatisticsPacketUnicastRx	1.3.6.1.4.1.171.10.94.89.89.141.1.1.8	Counter	read-only	Amount of packets per category
CTR rlStatisticsPacketMulticastRx	1.3.6.1.4.1.171.10.94.89.89.141.1.1.9	Counter	read-only	Amount of packets per category
CTR rlStatisticsPacketBroadcastRx	1.3.6.1.4.1.171.10.94.89.89.141.1.1.10	Counter	read-only	Amount of packets per category
CTR rlStatisticsPacketRxBytes	1.3.6.1.4.1.171.10.94.89.89.141.1.1.11	Counter	read-only	Amount of RX Bytes
CTR rlStatisticsPacketRxFrames	1.3.6.1.4.1.171.10.94.89.89.141.1.1.12	Counter	read-only	Amount of RX Frames
CTR rlStatisticsPacketTxBytes	1.3.6.1.4.1.171.10.94.89.89.141.1.1.13	Counter	read-only	Amount of TX Bytes
CTR rlStatisticsPacketTxFrames	1.3.6.1.4.1.171.10.94.89.89.141.1.1.14	Counter	read-only	Amount of TX Frames
rlStatisticsPortTable	1.3.6.1.4.1.171.10.94.89.89.141.2		read-only	Dlink Port statistics MIB Table
rlStatisticsPortEntry	1.3.6.1.4.1.171.10.94.89.89.141.2.1		read-only	Row definition for port statistic table.
CTR rlStatisticsPortRx	1.3.6.1.4.1.171.10.94.89.89.141.2.1.1	Counter	read-only	Amount of inbound traffic per port
CTR rlStatisticsPortTx	1.3.6.1.4.1.171.10.94.89.89.141.2.1.2	Counter	read-only	Amount of outbound traffic per port
INT rlStatisticsPortUtilization	1.3.6.1.4.1.171.10.94.89.89.141.2.1.3	INTEGER	read-only	utilization percentage per port

RFC description

D-Link network switch statistics MIB for packet statistics, packet sizes, and frame counters on network interfaces.

Start monitoring D-Link 3100 series switch (DES/DGS-3100), per-port traffic/error statistics with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINK-3100-STATISTICS-MIB

What Is DLINK-3100-STATISTICS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description