DGS3324SRi-SWL3MGMT-MIB

All MIBs › DGS3324SRi-SWL3MGMT-MIB

Last Updated: 2000-07-15

Category: Technology: Routing/L3, Vendor: D-Link

Description: L3 management MIB for D-Link DGS-3324SRi stackable switch covering routing, OSPF, and Layer 3 management objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DGS3324SRi-SWL3MGMT-MIB?

DGS3324SRi-SWL3MGMT-MIB is a vendor-specific D-Link MIB (swL3MgmtMIB) providing Layer 3 routing management for the DGS-3324SRi stackable Gigabit switch. It exposes protocol-level enable/disable controls for RIPv2, OSPF, DVMRP, PIM, and VRRP, IP interface configuration via swL3IpCtrlTable (address, subnet mask, VLAN binding, secondary-address flag, row status), a forwarding/static-route table, DHCP/BOOTP and DNS relay configuration, MD5 authentication keys and route redistribution settings, a substantial OSPF sub-tree (host routes, virtual and physical OSPF interfaces), and a PIM sub-tree covering candidate bootstrap routers, candidate RPs, shortest-path-tree mode, and static RP mappings. Monitoring it lets operators verify which L3 routing protocols are enabled, confirm IP interface and VLAN bindings are correctly applied, and check OSPF/PIM adjacency and rendezvous-point configuration — essential for diagnosing routing black holes or multicast RP misconfiguration. It's deployed specifically on D-Link DGS-3324SRi switches, registered under the dgs3324SRi enterprise branch, and administrators can find the DGS3324SRi-SWL3MGMT-MIB MIB useful for auditing routing configuration via SNMP.

IPNetwork Monitor allows you to monitor SNMP objects defined in DGS3324SRi-SWL3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DGS-3324SRi stackable Layer 3 Gigabit switches

Monitoring Examples

An operator polls swL3IpCtrlTable for the IP address and operational state on a routed VLAN interface and cross-checks that OSPF is enabled globally; an interface showing an operationally down state while OSPF is enabled would explain why expected OSPF neighbors aren't forming on that VLAN.

What Can Be Monitored

per-protocol routing enable state (RIP, OSPF, DVMRP, PIM, VRRP)
IP interface configuration and operational state
static route and IP forwarding table entries
DHCP/BOOTP and DNS relay configuration
OSPF host/virtual/physical interface tables
PIM candidate RP/BSR and static RP mappings

Imported Objects

From IF-MIB

InterfaceIndex

From OSPF-MIB

AreaID
DesignatedRouterPriority
HelloRange
Metric
PositiveInteger
RouterID
Status
TOSType
UpToMaxAge

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TruthValue

From SW-PROJECTX-SRPRIMGMT-MIB

dgs3324SRi

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using swL3ospfVirtIfEvents OID:

Select a D-Link DGS-3324SRi stackable Layer 3 Gigabit switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL3ospfVirtIfEvents into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of state changes or error events on this Virtual Link. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL3MgmtMIB	1.3.6.1.4.1.171.11.59.4.3			The Structure of Layer 3 Network Management Information for the proprietary enterprise.
swL3DevMgmt	1.3.6.1.4.1.171.11.59.4.3.1
swL3DevCtrl	1.3.6.1.4.1.171.11.59.4.3.1.1
INT swL3DevCtrlRIPState	1.3.6.1.4.1.171.11.59.4.3.1.1.1	INTEGER	read-write	This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.
INT swL3DevCtrlOSPFState	1.3.6.1.4.1.171.11.59.4.3.1.1.2	INTEGER	read-write	This object indicates OSPF protocol is enabled or disabled.
INT swL3DevCtrlDVMRPState	1.3.6.1.4.1.171.11.59.4.3.1.1.3	INTEGER	read-write	This object indicates DVMRP protocol is enabled or disabled.
INT swL3DevCtrlPIMState	1.3.6.1.4.1.171.11.59.4.3.1.1.4	INTEGER	read-write	This object indicates PIM protocol is enabled or disabled.
INT swL3DevCtrlVRRPState	1.3.6.1.4.1.171.11.59.4.3.1.1.5	INTEGER	read-write	This object indicates VRRP protocol is enabled or disabled.
swL3IpMgmt	1.3.6.1.4.1.171.11.59.4.3.2
swL3IpCtrlMgmt	1.3.6.1.4.1.171.11.59.4.3.2.1
swL3IpCtrlTable	1.3.6.1.4.1.171.11.59.4.3.2.1.1		not-accessible	This table contain IP interface information.
swL3IpCtrlEntry	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1		not-accessible	A list of information about a specific IP interface.
IP swL3IpCtrlIpAddr	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.1	IpAddress	not-accessible	The IP address of the interface. This object only can take the value of the unicast IP address.
INT swL3IpCtrlIfIndex	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.2	INTEGER	read-only	This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
STR swL3IpCtrlInterfaceName	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.3	DisplayString	read-create	This object indicates the name of the IP interface.
IP swL3IpCtrlIpSubnetMask	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.4	IpAddress	read-create	The IP net mask for this interface.
STR swL3IpCtrlVlanName	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.5	DisplayString	read-create	This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
INT swL3IpCtrlMode	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.6	INTEGER	read-create	This object indicates the IP operation mode. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. manual(2) - the IP address will be set by manual. bootp(3) - the IP address will be set automatically from BOOTP server. dhcp(4) - the IP address will be set automatically from DHCP server.
T/F swL3IpCtrlSecondary	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.7	TruthValue	read-create	When this is true(1) the IP address is the secondary IP. When false(2), the IP address is the primary IP.
ROW swL3IpCtrlState	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.8	RowStatus	read-create	This variable displays the status of the entry. The status used for creating, modifying, and deleting instances of the objects in this table.
INT swL3IpCtrlOperState	1.3.6.1.4.1.171.11.59.4.3.2.1.1.1.9	INTEGER	read-only	The current operational state of the IP interface.
swL3IpFdbMgmt	1.3.6.1.4.1.171.11.59.4.3.2.2
swL3IpFdbInfoTable	1.3.6.1.4.1.171.11.59.4.3.2.2.1		not-accessible	A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
swL3IpFdbInfoEntry	1.3.6.1.4.1.171.11.59.4.3.2.2.1.1		not-accessible	Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
IP swL3IpFdbInfoIpAddr	1.3.6.1.4.1.171.11.59.4.3.2.2.1.1.1	IpAddress	read-only	A IP address for which switch has forwarding and/or filtering information.
IP swL3IpFdbInfoIpSubnetMask	1.3.6.1.4.1.171.11.59.4.3.2.2.1.1.2	IpAddress	read-only	A IP net mask for this interface.for which switch has forwarding and/or filtering information.
INT swL3IpFdbInfoPort	1.3.6.1.4.1.171.11.59.4.3.2.2.1.1.3	INTEGER	read-only	Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
INT swL3IpFdbInfoType	1.3.6.1.4.1.171.11.59.4.3.2.2.1.1.4	INTEGER	read-only	The status of this entry.
INT swL3IpArpAgingTime	1.3.6.1.4.1.171.11.59.4.3.2.4	INTEGER	read-write	The timeout period in minutes for aging out dynamically learned arp information.
swL3IpStaticRouteTable	1.3.6.1.4.1.171.11.59.4.3.2.5		not-accessible	This entity's IP static Routing table.
swL3IpStaticRouteEntry	1.3.6.1.4.1.171.11.59.4.3.2.5.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action.
IP swL3IpStaticRouteDest	1.3.6.1.4.1.171.11.59.4.3.2.5.1.1	IpAddress	read-only	The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
IP swL3IpStaticRouteMask	1.3.6.1.4.1.171.11.59.4.3.2.5.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
INT swL3IpStaticRouteBkupState	1.3.6.1.4.1.171.11.59.4.3.2.5.1.3	INTEGER	read-only	The routing state for this route.The value SHOULD be primary(1) or backup(2).
IP swL3IpStaticRouteNextHop	1.3.6.1.4.1.171.11.59.4.3.2.5.1.4	IpAddress	read-create	On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.
INT swL3IpStaticRouteMetric	1.3.6.1.4.1.171.11.59.4.3.2.5.1.5	INTEGER	read-create	The routing metric for this route.
INT swL3IpStaticRouteStatus	1.3.6.1.4.1.171.11.59.4.3.2.5.1.6	INTEGER	read-create	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
swL3RelayMgmt	1.3.6.1.4.1.171.11.59.4.3.3
swL3RelayBootpMgmt	1.3.6.1.4.1.171.11.59.4.3.3.1
INT swL3RelayBootpState	1.3.6.1.4.1.171.11.59.4.3.3.1.1	INTEGER	read-write	This object indicates BOOTP Relay function is enabled or disabled.
INT swL3RelayBootpHopCount	1.3.6.1.4.1.171.11.59.4.3.3.1.2	INTEGER	read-write	This object indicates the maximum number of router hops that the BOOTP packets can cross.
INT swL3RelayBootpTimeThreshold	1.3.6.1.4.1.171.11.59.4.3.3.1.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the BOOTP request. If this time is exceeded, the switch will drop the BOOTP packet.
swL3RelayBootpCtrlTable	1.3.6.1.4.1.171.11.59.4.3.3.1.4		not-accessible	This table specifys the IP address as a destination to forward (relay) BOOTP packets to.
swL3RelayBootpCtrlEntry	1.3.6.1.4.1.171.11.59.4.3.3.1.4.1		not-accessible	A list of information specifies the IP address as a destination to forward (relay) BOOTP packets to.
STR swL3RelayBootpCtrlInterfaceName	1.3.6.1.4.1.171.11.59.4.3.3.1.4.1.1	DisplayString	read-only	The name of the IP interface.
IP swL3RelayBootpCtrlServer	1.3.6.1.4.1.171.11.59.4.3.3.1.4.1.2	IpAddress	read-only	The BOOTP server IP address.
INT swL3RelayBootpCtrlState	1.3.6.1.4.1.171.11.59.4.3.3.1.4.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
swL3RelayDnsMgmt	1.3.6.1.4.1.171.11.59.4.3.3.2
INT swL3RelayDnsState	1.3.6.1.4.1.171.11.59.4.3.3.2.1	INTEGER	read-write	This object indicates DNS Relay function is enabled or disabled.
IP swL3RelayDnsPrimaryServer	1.3.6.1.4.1.171.11.59.4.3.3.2.2	IpAddress	read-write	This object indicates the address of the primary DNS server.
IP swL3RelayDnsSecondaryServer	1.3.6.1.4.1.171.11.59.4.3.3.2.3	IpAddress	read-write	This object indicates the address of the secondary DNS server.
INT swL3RelayDnsCacheState	1.3.6.1.4.1.171.11.59.4.3.3.2.4	INTEGER	read-write	This object indicates DNS Relay cache is enabled or disabled.
INT swL3RelayDnsStaticTableState	1.3.6.1.4.1.171.11.59.4.3.3.2.5	INTEGER	read-write	This object indicates DNS Relay static table is enabled or disabled.
swL3RelayDnsCtrlTable	1.3.6.1.4.1.171.11.59.4.3.3.2.6		not-accessible	This table display the current DNS relay static table.
swL3RelayDnsCtrlEntry	1.3.6.1.4.1.171.11.59.4.3.3.2.6.1		not-accessible	A list of information display the current DNS relay static table.
STR swL3RelayDnsCtrlDomainName	1.3.6.1.4.1.171.11.59.4.3.3.2.6.1.1	DisplayString	read-only	The domain name of the entry.
IP swL3RelayDnsCtrlIpAddr	1.3.6.1.4.1.171.11.59.4.3.3.2.6.1.2	IpAddress	read-only	The IP address of the entry.
INT swL3RelayDnsCtrlState	1.3.6.1.4.1.171.11.59.4.3.3.2.6.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
swL3Md5Table	1.3.6.1.4.1.171.11.59.4.3.4		not-accessible	This table display the current MD5 key table.
swL3Md5Entry	1.3.6.1.4.1.171.11.59.4.3.4.1		not-accessible	A list of information display the current MD5 key table.
INT swL3Md5KeyId	1.3.6.1.4.1.171.11.59.4.3.4.1.1	INTEGER	read-only	The MD5 key ID.
STR swL3Md5Key	1.3.6.1.4.1.171.11.59.4.3.4.1.2	DisplayString	read-create	An MD5 password of up to 16 bytes.
ROW swL3Md5RowStatus	1.3.6.1.4.1.171.11.59.4.3.4.1.3	RowStatus	read-create	This object indicates the status of this entry.
swL3RouteRedistriTable	1.3.6.1.4.1.171.11.59.4.3.5		not-accessible	Route redistribution allows routers on the network. That are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the vairous router��s routing tables and assinging appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
swL3RouteRedistriEntry	1.3.6.1.4.1.171.11.59.4.3.5.1		not-accessible	A list of information display the route redistribution table.
INT swL3RouteRedistriSrcProtocol	1.3.6.1.4.1.171.11.59.4.3.5.1.1	INTEGER	read-only	Allows the selection of the protocol of the source device.
INT swL3RouteRedistriDstProtocol	1.3.6.1.4.1.171.11.59.4.3.5.1.2	INTEGER	read-only	Allows the selection of the protocol of the destination device.
INT swL3RouteRedistriType	1.3.6.1.4.1.171.11.59.4.3.5.1.3	INTEGER	read-create	Allows the selection of one of the methods for calcalculating the metric value.
INT swL3RouteRedistriMetric	1.3.6.1.4.1.171.11.59.4.3.5.1.4	INTEGER	read-create	Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
ROW swL3RouteRedistriRowStatus	1.3.6.1.4.1.171.11.59.4.3.5.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL3OspfHostTable	1.3.6.1.4.1.171.11.59.4.3.6		not-accessible	The list of Hosts, and their metrics, that the router will advertise as host routes.
swL3OspfHostEntry	1.3.6.1.4.1.171.11.59.4.3.6.1		not-accessible	A metric to be advertised, for a given type of service, when a given host is reachable.
IP swL3OspfHostIpAddress	1.3.6.1.4.1.171.11.59.4.3.6.1.1	IpAddress	read-only	The IP Address of the Host.
TOS swL3OspfHostTOS	1.3.6.1.4.1.171.11.59.4.3.6.1.2	TOSType	read-only	The Type of Service of the route being configured.
MET swL3OspfHostMetric	1.3.6.1.4.1.171.11.59.4.3.6.1.3	Metric	read-create	The Metric to be advertised.
ARE swL3OspfHostAreaID	1.3.6.1.4.1.171.11.59.4.3.6.1.4	AreaID	read-create	The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0
ROW swL3OspfHostStatus	1.3.6.1.4.1.171.11.59.4.3.6.1.5	RowStatus	read-create	This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfVirtIfTable	1.3.6.1.4.1.171.11.59.4.3.7		not-accessible	Information about this router's virtual inter- faces.
swL3ospfVirtIfEntry	1.3.6.1.4.1.171.11.59.4.3.7.1		not-accessible	Information about a single Virtual Interface.
ARE swL3ospfVirtIfAreaId	1.3.6.1.4.1.171.11.59.4.3.7.1.1	AreaID	read-only	The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
ROU swL3ospfVirtIfNeighbor	1.3.6.1.4.1.171.11.59.4.3.7.1.2	RouterID	read-only	The Router ID of the Virtual Neighbor.
UPT swL3ospfVirtIfTransitDelay	1.3.6.1.4.1.171.11.59.4.3.7.1.3	UpToMaxAge	read-create	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
UPT swL3ospfVirtIfRetransInterval	1.3.6.1.4.1.171.11.59.4.3.7.1.4	UpToMaxAge	read-create	The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time.
HEL swL3ospfVirtIfHelloInterval	1.3.6.1.4.1.171.11.59.4.3.7.1.5	HelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
NUM swL3ospfVirtIfRtrDeadInterval	1.3.6.1.4.1.171.11.59.4.3.7.1.6	PositiveInteger	read-create	The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
INT swL3ospfVirtIfState	1.3.6.1.4.1.171.11.59.4.3.7.1.7	INTEGER	read-only	OSPF virtual interface states.
C32 swL3ospfVirtIfEventsEx	1.3.6.1.4.1.171.11.59.4.3.7.1.8	Counter32	read-only	The number of state changes or error events on this Virtual Link
INT swL3ospfVirtIfAuthType	1.3.6.1.4.1.171.11.59.4.3.7.1.9	INTEGER	read-create	The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
OCT swL3ospfVirtIfAuthKey	1.3.6.1.4.1.171.11.59.4.3.7.1.10	OCTET STRING	read-create	If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment.
INT swL3ospfVirtIfAuthKeyID	1.3.6.1.4.1.171.11.59.4.3.7.1.11	INTEGER	read-create	The MD5 key ID.
ROW swL3ospfVirtIfStatus	1.3.6.1.4.1.171.11.59.4.3.7.1.12	RowStatus	read-create	This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfIfTable	1.3.6.1.4.1.171.11.59.4.3.8		not-accessible	The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
swL3ospfIfEntry	1.3.6.1.4.1.171.11.59.4.3.8.1		not-accessible	The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.
IP swL3ospfIfIpAddress	1.3.6.1.4.1.171.11.59.4.3.8.1.1	IpAddress	read-only	The IP address of this OSPF interface.
I32 swL3ospfAddressLessIf	1.3.6.1.4.1.171.11.59.4.3.8.1.2	Integer32	read-only	For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.
ARE swL3ospfIfAreaId	1.3.6.1.4.1.171.11.59.4.3.8.1.3	AreaID	read-create	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT swL3ospfIfType	1.3.6.1.4.1.171.11.59.4.3.8.1.4	INTEGER	read-create	The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
STA swL3ospfIfAdminStat	1.3.6.1.4.1.171.11.59.4.3.8.1.5	Status	read-create	The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
DES swL3ospfIfRtrPriority	1.3.6.1.4.1.171.11.59.4.3.8.1.6	DesignatedRouterPriority	read-create	The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
UPT swL3ospfIfTransitDelay	1.3.6.1.4.1.171.11.59.4.3.8.1.7	UpToMaxAge	read-create	The estimated number of seconds it takes to transmit a link state update packet over this interface.
UPT swL3ospfIfRetransInterval	1.3.6.1.4.1.171.11.59.4.3.8.1.8	UpToMaxAge	read-create	The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
HEL swL3ospfIfHelloInterval	1.3.6.1.4.1.171.11.59.4.3.8.1.9	HelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
NUM swL3ospfIfRtrDeadInterval	1.3.6.1.4.1.171.11.59.4.3.8.1.10	PositiveInteger	read-create	The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
NUM swL3ospfIfPollInterval	1.3.6.1.4.1.171.11.59.4.3.8.1.11	PositiveInteger	read-create	The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
INT swL3ospfIfState	1.3.6.1.4.1.171.11.59.4.3.8.1.12	INTEGER	read-only	The OSPF Interface State.
IP swL3ospfIfDesignatedRouter	1.3.6.1.4.1.171.11.59.4.3.8.1.13	IpAddress	read-only	The IP Address of the Designated Router.
IP swL3ospfIfBackupDesignatedRouter	1.3.6.1.4.1.171.11.59.4.3.8.1.14	IpAddress	read-only	The IP Address of the Backup Designated Router.
C32 swL3ospfIfEvents	1.3.6.1.4.1.171.11.59.4.3.8.1.15	Counter32	read-only	The number of times this OSPF interface has changed its state, or an error has occurred.
INT swL3ospfIfMulticastForwarding	1.3.6.1.4.1.171.11.59.4.3.8.1.16	INTEGER	read-create	The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
T/F swL3ospfIfDemand	1.3.6.1.4.1.171.11.59.4.3.8.1.17	TruthValue	read-create	Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
INT swL3ospfIfAuthType	1.3.6.1.4.1.171.11.59.4.3.8.1.18	INTEGER	read-create	The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
OCT swL3ospfIfAuthKey	1.3.6.1.4.1.171.11.59.4.3.8.1.19	OCTET STRING	read-create	The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero.
INT swL3ospfIfAuthKeyID	1.3.6.1.4.1.171.11.59.4.3.8.1.20	INTEGER	read-create	The MD5 key ID.
ROW swL3ospfIfStatus	1.3.6.1.4.1.171.11.59.4.3.8.1.21	RowStatus	read-create	This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3RoutePreference	1.3.6.1.4.1.171.11.59.4.3.9
INT swL3RoutePreferenceRIP	1.3.6.1.4.1.171.11.59.4.3.9.1	INTEGER	read-write	Used to configure the route preference of RIP.
INT swL3RoutePreferenceOSPFIntra	1.3.6.1.4.1.171.11.59.4.3.9.2	INTEGER	read-write	Used to configure the route preference of OSPF Intra.
INT swL3RoutePreferenceStatic	1.3.6.1.4.1.171.11.59.4.3.9.3	INTEGER	read-write	Used to configure the route preference of Static.
INT swL3RoutePreferenceLocal	1.3.6.1.4.1.171.11.59.4.3.9.4	INTEGER	read-only	Used to read the route preference of Local.
INT swL3RoutePreferenceOSPFInter	1.3.6.1.4.1.171.11.59.4.3.9.5	INTEGER	read-write	Used to configure the route preference of OSPF Inter.
INT swL3RoutePreferenceOSPFExtT1	1.3.6.1.4.1.171.11.59.4.3.9.6	INTEGER	read-write	Used to configure the route preference of OSPFExtT1.
INT swL3RoutePreferenceOSPFExtT2	1.3.6.1.4.1.171.11.59.4.3.9.7	INTEGER	read-write	Used to configure the route preference of OSPF ExtT2.
swL3PimMgmt	1.3.6.1.4.1.171.11.59.4.3.11
swL3PimCbsrInfoMgmt	1.3.6.1.4.1.171.11.59.4.3.11.1
I32 swL3pimCbsrBootStrapPeriod	1.3.6.1.4.1.171.11.59.4.3.11.1.1	Integer32	read-write	At the elected BSR, this is the interval between originating Bootstrap messages, and should be equal to 60 seconds.
I32 swL3pimCbsrHashMaskLen	1.3.6.1.4.1.171.11.59.4.3.11.1.2	Integer32	read-write	The length (in bits) of the mask to use in the hash function. For IPv4 we recommend a value of 30. For IPv6 we recommand a value of 126.
swL3pimCbsrTable	1.3.6.1.4.1.171.11.59.4.3.11.1.3		not-accessible	The PIM CBSR Table contains the cbsr related information, like interface and priority.
swL3pimCbsrEntry	1.3.6.1.4.1.171.11.59.4.3.11.1.3.1		not-accessible	An entry in the PIM CBSR Table.
NUM swL3pimCbsrInterface	1.3.6.1.4.1.171.11.59.4.3.11.1.3.1.1	InterfaceIndex	not-accessible	The ifIndex value of this PIM interface.
I32 swL3pimCbsrPriority	1.3.6.1.4.1.171.11.59.4.3.11.1.3.1.2	Integer32	read-write	The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface.
swL3pimCandidateRPMgmt	1.3.6.1.4.1.171.11.59.4.3.11.2
I32 swL3pimCandidateRPHoldtime	1.3.6.1.4.1.171.11.59.4.3.11.2.1	Integer32	read-write	For C-RPs, this is the Holdtime specified in C-RP-Adv message, and is used by the BSR to time out RPs. This should be set to 2.5 * [C-RP-Adv-Period]. Default: 150 seconds.
I32 swL3pimCandidateRPPriority	1.3.6.1.4.1.171.11.59.4.3.11.2.2	Integer32	read-write	The 'priority' of the included RP, for the corresponding Encoded-Group Address (if any), highest priority is '0' (i.e. the lower the value of the 'Priority' field, the higher the priority). This field is stored at the BSR upon receipt along with the RP address and corresponding Encoded-Group Address.
I32 swL3pimCandidateRPWildcardPrefixCnt	1.3.6.1.4.1.171.11.59.4.3.11.2.3	Integer32	read-write	The number of enocded group addresses included in the message; indicating the group prefixes for which the C-RP is advertising. A Prefix-Cnt of '0' implies a prefix of 224.0.0.0 with mask length of 4; i.e. all multicast groups. If the C-RP is not configured with Group-prefix information, the C-RP puts a default value of '0' in this field.
swL3pimSptMgmt	1.3.6.1.4.1.171.11.59.4.3.11.3
STR swL3pimLastHopSptThreshold	1.3.6.1.4.1.171.11.59.4.3.11.3.1	DisplayString	read-write	Specifies a last hop router threshold.
STR swL3pimRPSptThreshold	1.3.6.1.4.1.171.11.59.4.3.11.3.2	DisplayString	read-write	Specifies an RP threshold.
swL3pimRegChksumIncDataTable	1.3.6.1.4.1.171.11.59.4.3.11.4		not-accessible	The PIM Register Checksum Including Data Table contains the PIM register checksum including data information, like RP address and state.
swL3pimRegChksumIncDataEntry	1.3.6.1.4.1.171.11.59.4.3.11.4.1		not-accessible	An entry in the PIM Register Checksum Including Data Table.
IP swL3SwL3pimRegChksumIncDataRpAddr	1.3.6.1.4.1.171.11.59.4.3.11.4.1.1	IpAddress	not-accessible	Specifies the RP address.
ROW swL3SwL3pimRegChksumIncDataState	1.3.6.1.4.1.171.11.59.4.3.11.4.1.2	RowStatus	read-create	The state of register checksum including data for RPs.
swL3PimInfoMgmt	1.3.6.1.4.1.171.11.59.4.3.11.5
I32 swL3pimRegisterProbeTime	1.3.6.1.4.1.171.11.59.4.3.11.5.1	Integer32	read-write	When null Registers are used, this is the time between sending a null Register and the Register-Suppression-Timer expiring unless it is restarted by receiving a Register-Stop. Thus, a null Register would be sent when the Register-Suppression-Timer reaches this value. Default: 5 seconds.
I32 swL3pimRegisterSuppressionTime	1.3.6.1.4.1.171.11.59.4.3.11.5.2	Integer32	read-write	This is the mean interval between receiving a Register-Stop and allowing Registers to be sent again. A lower value means more frequent register bursts at RP, while a higher value means longer join latency for new receiver. Default: 60 seconds.
swL3pimInfoTable	1.3.6.1.4.1.171.11.59.4.3.11.5.3		not-accessible	The PIM Information Table contains the PIM related information, like DR priority.
swL3pimInfoEntry	1.3.6.1.4.1.171.11.59.4.3.11.5.3.1		not-accessible	An entry in the PIM Information Table.
NUM swL3pimInterface	1.3.6.1.4.1.171.11.59.4.3.11.5.3.1.1	InterfaceIndex	not-accessible	The ifIndex value of this PIM interface.
U32 swL3pimDRPriority	1.3.6.1.4.1.171.11.59.4.3.11.5.3.1.2	Unsigned32	read-write	The DR Priority is a 32-bit unsigned number and the numerically larger priority is always prefered. A router's idea of the current DR on an interface can change when a PIM Hello message is received, when a neighbor timers out, or when a router's own DR priority changes.
swL3pimStaticRPTable	1.3.6.1.4.1.171.11.59.4.3.11.6		not-accessible	The PIM Static RP Table contains the PIM static RP related information, like group address, group mask, RP address and RP row status.
swL3pimStaticRPEntry	1.3.6.1.4.1.171.11.59.4.3.11.6.1		not-accessible	An entry in the PIM Static RP Table.
IP swL3pimStaticRPGroupAddress	1.3.6.1.4.1.171.11.59.4.3.11.6.1.1	IpAddress	not-accessible	The IP multicast group address which, when combined with swL3pimStaticRPGroupMask, identifies a group prefix for which the local router will advertise itself as a static RP.
IP swL3pimStaticRPGroupMask	1.3.6.1.4.1.171.11.59.4.3.11.6.1.2	IpAddress	not-accessible	The multicast group address mask which, when combined with swL3pimStaticRPGroupAddress, identifies a group prefix for which the local router will advertise itself as a static RP.
IP swL3pimStaticRPAddress	1.3.6.1.4.1.171.11.59.4.3.11.6.1.3	IpAddress	not-accessible	The (unicast) address of the interface which will be advertised as a static RP.
ROW swL3pimStaticRPRowStatus	1.3.6.1.4.1.171.11.59.4.3.11.6.1.4	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.

RFC description

Layer 3 network management for D-Link DGS3324SRi, supporting RIP, OSPF, DVMRP routing protocols.

Start monitoring D-Link DGS-3324SRi stackable Layer 3 Gigabit switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DGS3324SRi-SWL3MGMT-MIB