DES3526-L2MGMT-MIB

All MIBs › DES3526-L2MGMT-MIB

Organization: D-Link Corp.

Last Updated: 2009-04-02

Category: VLAN and Bridging, Vendor: D-Link

Description: Manages L2 switching, VLAN, STP, and port security for D-Link DES-3526 switch.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3526-L2MGMT-MIB?

DES3526-L2MGMT-MIB is a D-Link proprietary MIB defining Layer 2 network management information for the DES-3526 managed switch. Its objects cover system uptime, total/in-use port counts, console-in-use flag, module type, a power-supply status table, spanning-tree state, IGMP snooping, RMON state, statistics-counter reset, FDB-table VLAN scoping, MAC-notification state/history-size/interval, asymmetric-VLAN state, management VLAN ID, Telnet state/TCP port, and LLDP state/advertised-system-IP. As a configuration/status MIB it lets an administrator confirm core Layer 2 settings — spanning tree, IGMP snooping, management VLAN — on a DES-3526 switch. It is deployed on the D-Link DES-3526 managed switch. Engineers can download the DES3526-L2MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3526-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3526 managed switch

Monitoring Examples

An administrator checks swL2DevCtrlStpState and swL2DevCtrlIGMPSnooping to confirm spanning-tree and multicast-snooping are both enabled as expected on a D-Link DES-3526 switch.

What Can Be Monitored

spanning-tree, IGMP snooping, and management VLAN configuration

Imported Objects

From RFC1213-MIB

DisplayString

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Counter64
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus

From SW3500PRIMGMT-MIB

des3526

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.64.1.2			The Structure of Layer 2 Network Management Information for the proprietary enterprise.
swL2DevMgmt	1.3.6.1.4.1.171.11.64.1.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.64.1.2.1.1
TIK swDevInfoSystemUpTime	1.3.6.1.4.1.171.11.64.1.2.1.1.1	TimeTicks	read-only	The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in the units of seconds.
INT swDevInfoTotalNumOfPort	1.3.6.1.4.1.171.11.64.1.2.1.1.2	INTEGER	read-only	The number of ports within this switch. This value is the sum of the ports within this switch.
INT swDevInfoNumOfPortInUse	1.3.6.1.4.1.171.11.64.1.2.1.1.3	INTEGER	read-only	The number of ports in this switch connected to the segment or the end stations.
INT swDevInfoConsoleInUse	1.3.6.1.4.1.171.11.64.1.2.1.1.4	INTEGER	read-only	The usage indication of the console system.
OCT swDevInfoModuleType	1.3.6.1.4.1.171.11.64.1.2.1.1.5	OCTET STRING	read-only	This object indicates the module type of this port.
swDevInfoPowerTable	1.3.6.1.4.1.171.11.64.1.2.1.1.8		not-accessible	A list of the temperature.
swDevInfoPowerEntry	1.3.6.1.4.1.171.11.64.1.2.1.1.8.1		not-accessible	An entry for Power information.
INT swDevInfoPowerUnitIndex	1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.1	INTEGER	read-only	Indicates the ID of the unit in the System
INT swDevInfoPowerID	1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.2	INTEGER	read-only	Indicates ID of the power
INT swDevInfoPowerStatus	1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.3	INTEGER	read-only	Indicates status of the power
swL2DevCtrl	1.3.6.1.4.1.171.11.64.1.2.1.2
INT swL2DevCtrlStpState	1.3.6.1.4.1.171.11.64.1.2.1.2.1	INTEGER	read-write	This object can enable or disable the spanning tree algorithm during the runtime of the system.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.64.1.2.1.2.2	INTEGER	read-write	This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function has been enabled or disabled.
INT swL2DevCtrlRmonState	1.3.6.1.4.1.171.11.64.1.2.1.2.3	INTEGER	read-write	This object can be enable or disable RMON.
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.64.1.2.1.2.8	INTEGER	read-write	If the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
VLA swL2DevCtrlVlanIdOfFDBTbl	1.3.6.1.4.1.171.11.64.1.2.1.2.9	VlanId	read-write	Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is the DEFAULT_VLAN_ID of the system.
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.64.1.2.1.2.10	INTEGER	read-write	This object can enable or disable MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.64.1.2.1.2.11	INTEGER	read-write	This object indicates the history size of variation MAC in the address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.64.1.2.1.2.12	INTEGER	read-write	This object indicates the time interval in seconds for triggering the MAC notify message.
INT swL2DevCtrlAsymVlanState	1.3.6.1.4.1.171.11.64.1.2.1.2.13	INTEGER	read-write	This object can enable or disable asymmetric VLANs during the runtime of the system.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.64.1.2.1.2.14	VlanId	read-write	This object controls which Vlan includes system ip and that the Vlan should have been created.
swL2DevCtrlTelnet	1.3.6.1.4.1.171.11.64.1.2.1.2.15
INT swL2DevCtrlTelnetState	1.3.6.1.4.1.171.11.64.1.2.1.2.15.1	INTEGER	read-write	This object controls the Telnet status.
INT swL2DevCtrlTelnetTcpPort	1.3.6.1.4.1.171.11.64.1.2.1.2.15.2	INTEGER	read-write	This object can designate a TCP port. When Telnet is disabled this object isn't accessible.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.64.1.2.1.2.16	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
swL2DevCtrlWeb	1.3.6.1.4.1.171.11.64.1.2.1.2.17
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.11.64.1.2.1.2.17.1	INTEGER	read-write	This object controls Web status.
INT swL2DevCtrlWebTcpPort	1.3.6.1.4.1.171.11.64.1.2.1.2.17.2	INTEGER	read-write	This object can designate a TCP port. When Web is disabled this object isn't accessible.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.64.1.2.1.2.18	INTEGER	read-write	When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded.
INT swL2DevCtrlLLDPAdviseSystemIP	1.3.6.1.4.1.171.11.64.1.2.1.2.19	INTEGER	read-write	Used to advise system ip to all port
INT swL2DevCtrPasswordRecoveryState	1.3.6.1.4.1.171.11.64.1.2.1.2.20	INTEGER	read-write	This object controls Password Recovery status.
swL2DevAlarm	1.3.6.1.4.1.171.11.64.1.2.1.3
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.171.11.64.1.2.1.3.1	INTEGER	read-write	When the device has become the new root of Spanning Tree, this object decides whether to send a new root trap.
INT swL2DevAlarmTopologyChange	1.3.6.1.4.1.171.11.64.1.2.1.3.2	INTEGER	read-write	This object determines whether to send a trap or not when the switch topology has changed. If the object is enabled(3), the topology change trap is sent by the device when any of its configured ports transition from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device doesn't send the trap if this object value is set to disabled or other.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.64.1.2.1.3.3	INTEGER	read-write	This object determines whether to send a trap or not when the link has changed. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device doesn't send the trap if this object value is set to disabled or other.
swL2VlanMgmt	1.3.6.1.4.1.171.11.64.1.2.3
swL2VlanAdvertisementTable	1.3.6.1.4.1.171.11.64.1.2.3.1		not-accessible	A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
swL2VlanAdvertisementEntry	1.3.6.1.4.1.171.11.64.1.2.3.1.1		not-accessible	Advertisement state for each VLAN configured in the device.
INT swL2VlanIndex	1.3.6.1.4.1.171.11.64.1.2.3.1.1.1	INTEGER	read-only	The VLAN-ID or other identifier referring to this VLAN.
STR swL2VlanName	1.3.6.1.4.1.171.11.64.1.2.3.1.1.2	DisplayString	read-only	An administratively assigned string, which may be used to identify the VLAN.
INT swL2VlanAdvertiseState	1.3.6.1.4.1.171.11.64.1.2.3.1.1.3	INTEGER	read-write	This object indicates the advertised status of this VLAN entry.
swL2PortMgmt	1.3.6.1.4.1.171.11.64.1.2.4
swL2PortInfoTable	1.3.6.1.4.1.171.11.64.1.2.4.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.64.1.2.4.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.64.1.2.4.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module).
INT swL2PortInfoUnitIndex	1.3.6.1.4.1.171.11.64.1.2.4.1.1.2	INTEGER	read-only	Indicates ID of the unit in the device
INT swL2PortInfoType	1.3.6.1.4.1.171.11.64.1.2.4.1.1.3	INTEGER	read-only	This object indicates the connector type of this port.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.64.1.2.4.1.1.4	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.64.1.2.4.1.1.5	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInfoModuleType	1.3.6.1.4.1.171.11.64.1.2.4.1.1.6	INTEGER	read-only	This object indicates the module type of this port.
INT swL2PortInfoErrorDisabled	1.3.6.1.4.1.171.11.64.1.2.4.1.1.7	INTEGER	read-only	This object indicates the blocking type of this port.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.64.1.2.4.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.64.1.2.4.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.64.1.2.4.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlUnitIndex	1.3.6.1.4.1.171.11.64.1.2.4.2.1.2	INTEGER	read-only	Indicates the ID of the unit in the device
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.3	INTEGER	read-write	This object decides whether the port is enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.4	INTEGER	read-write	Choose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.5	INTEGER	read-write	The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
INT swL2PortCtrlLockState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.6	INTEGER	read-write	This object decides whether the port is locked or not.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.7	INTEGER	read-write	This object decides whether MAC notification is enabled or not.
INT swL2PortCtrlMulticastfilter	1.3.6.1.4.1.171.11.64.1.2.4.2.1.8	INTEGER	read-write	This object decides the multicast packet filtering mode on this port .
INT swL2PortCtrlMdixState	1.3.6.1.4.1.171.11.64.1.2.4.2.1.11	INTEGER	read-write	This object decides the MDIX mode on this port.
swL2PortInformationTable	1.3.6.1.4.1.171.11.64.1.2.4.4		not-accessible	A table that contains information about every port.
swL2PortInformationEntry	1.3.6.1.4.1.171.11.64.1.2.4.4.1		not-accessible	A list of information for each port of the device.
INT swL2PortInformationPortIndex	1.3.6.1.4.1.171.11.64.1.2.4.4.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInformationMediumType	1.3.6.1.4.1.171.11.64.1.2.4.4.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortInformationUnitID	1.3.6.1.4.1.171.11.64.1.2.4.4.1.3	INTEGER	read-only	Indicates ID of the unit in the system
INT swL2PortInformationType	1.3.6.1.4.1.171.11.64.1.2.4.4.1.4	INTEGER	read-only	This object indicates the connector type of this port.
INT swL2PortInformationLinkStatus	1.3.6.1.4.1.171.11.64.1.2.4.4.1.5	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInformationNwayStatus	1.3.6.1.4.1.171.11.64.1.2.4.4.1.6	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInformationModuleType	1.3.6.1.4.1.171.11.64.1.2.4.4.1.7	INTEGER	read-only	This object indicates the module type of this port.
INT swL2PortInformationErrorDisabled	1.3.6.1.4.1.171.11.64.1.2.4.4.1.8	INTEGER	read-only	This object indicates the blocking type of this port.
swL2PortControlTable	1.3.6.1.4.1.171.11.64.1.2.4.5		not-accessible	A table that contains control information about every port.
swL2PortControlEntry	1.3.6.1.4.1.171.11.64.1.2.4.5.1		not-accessible	A list of control information for each port of the device.
INT swL2PortControlPortIndex	1.3.6.1.4.1.171.11.64.1.2.4.5.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortControlMediumType	1.3.6.1.4.1.171.11.64.1.2.4.5.1.2	INTEGER	read-only	Indicates the medium type of the port number.
INT swL2PortControlUnitIndex	1.3.6.1.4.1.171.11.64.1.2.4.5.1.3	INTEGER	read-only	Indicates ID of the unit in the device
INT swL2PortControlAdminState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.4	INTEGER	read-write	This object decides if the port is enabled or disabled.
INT swL2PortControlNwayState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.5	INTEGER	read-write	Choose the port speed, duplex mode, and N-Way function mode.
INT swL2PortControlFlowCtrlState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.6	INTEGER	read-write	The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
INT swL2PortControlLockState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.7	INTEGER	read-write	This object decides whether the port is locked or not.
INT swL2PortControlMACNotifyState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.8	INTEGER	read-write	This object sets each port's MAC notification state.
INT swL2PortControlMulticastfilter	1.3.6.1.4.1.171.11.64.1.2.4.5.1.9	INTEGER	read-write	This object controls the multicast port filtering mode for a specified port.
INT swL2PortControlMdixState	1.3.6.1.4.1.171.11.64.1.2.4.5.1.11	INTEGER	read-write	This object decides the MDIX mode on this port.
swL2LimitedMulticastMgmt	1.3.6.1.4.1.171.11.64.1.2.5
swL2MulticastRangeTable	1.3.6.1.4.1.171.11.64.1.2.5.1		not-accessible	.
swL2MulticastRangeEntry	1.3.6.1.4.1.171.11.64.1.2.5.1.1		not-accessible	A list of information contained in swL2MulticastRangeTable.
STR swL2MulticastRangeName	1.3.6.1.4.1.171.11.64.1.2.5.1.1.1	DisplayString	read-only	This object specifies the multicast range name.
IP swL2MulticastRangeFromIp	1.3.6.1.4.1.171.11.64.1.2.5.1.1.2	IpAddress	read-create	This object specifies the start IP address for this range.
IP swL2MulticastRangeToIp	1.3.6.1.4.1.171.11.64.1.2.5.1.1.3	IpAddress	read-create	This object specifies the end IP address for this range.
ROW swL2MulticastRangeRowStatus	1.3.6.1.4.1.171.11.64.1.2.5.1.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2LimitedMulticastPortInfo	1.3.6.1.4.1.171.11.64.1.2.5.2
swL2LimitedMulticastStatusTable	1.3.6.1.4.1.171.11.64.1.2.5.2.1		not-accessible	.
swL2LimitedMulticastStatusEntry	1.3.6.1.4.1.171.11.64.1.2.5.2.1.1		not-accessible	A list of information contained in swL2LimitedMulticastStatusTable.
INT swL2LimitedMulticastPort	1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.1	INTEGER	read-only	This object indicates the port.
INT swL2LimitedMulticastAccess	1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.2	INTEGER	read-write	This object indicates the access type.
INT swL2LimitedMulticastState	1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.3	INTEGER	read-write	This object indicates the state for this port.
swL2LimitedMulticastRangeTable	1.3.6.1.4.1.171.11.64.1.2.5.2.2		not-accessible	.
swL2LimitedMulticastRangeEntry	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1		not-accessible	A list of information contained in swL2LimitedMulticastRangeTable.
INT swL2LimitedMulticastID	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.1	INTEGER	read-only	This object indicates the range ID.
STR swL2LimitedMulticastRangeName	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.2	DisplayString	read-create
IP swL2LimitedMulticastFromIp	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.3	IpAddress	read-only	This object specifies the start IP address of the range on this port.
IP swL2LimitedMulticastToIp	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.4	IpAddress	read-only	This object specifies the end IP address of the range on this port.
ROW swL2LimitedMulticastRowStatus	1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL2QOSMgmt	1.3.6.1.4.1.171.11.64.1.2.6
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.11.64.1.2.6.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.11.64.1.2.6.1.1		not-accessible	A list of information contained in swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.11.64.1.2.6.1.1.1	INTEGER	read-only	Indicates the port.
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.11.64.1.2.6.1.1.2	INTEGER	read-write	Indicates the RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.11.64.1.2.6.1.1.3	INTEGER	read-write	Indicates the TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.11.64.1.2.6.1.1.4	INTEGER	read-only	The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.11.64.1.2.6.1.1.5	INTEGER	read-only	The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.11.64.1.2.6.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.11.64.1.2.6.2.1		not-accessible	A list of information contained in swL2QOSSchedulingTable.
INT swL2QOSSchedulingClassIndex	1.3.6.1.4.1.171.11.64.1.2.6.2.1.1	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxPkts	1.3.6.1.4.1.171.11.64.1.2.6.2.1.2	INTEGER	read-write	Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 255 can be specified.
INT swL2QOSSchedulingMaxLatency	1.3.6.1.4.1.171.11.64.1.2.6.2.1.3	INTEGER	read-write	Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmitting its packets. A value between 0 and 255 can be specified- with this value multiplied by 16 ms to arrive at the total allowed time for queue to transmit packets. For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.11.64.1.2.6.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.11.64.1.2.6.3.1		not-accessible	A list of information contained in swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.11.64.1.2.6.3.1.1	INTEGER	read-only	The 802.1p user priority .
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.11.64.1.2.6.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.11.64.1.2.6.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.11.64.1.2.6.4.1		not-accessible	A list of information contained in swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.11.64.1.2.6.4.1.1	INTEGER	read-only	Indicates the port number.
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.11.64.1.2.6.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch.
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.11.64.1.2.6.4.1.3	INTEGER	read-only	Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
swL2IpMacBindingMgmt	1.3.6.1.4.1.171.11.64.1.2.7
swL2IpMacBindingPortTable	1.3.6.1.4.1.171.11.64.1.2.7.1		not-accessible	The table specifies the port's ip-mac binding function.
swL2IpMacBindingPortEntry	1.3.6.1.4.1.171.11.64.1.2.7.1.1		not-accessible	A list of information about the port's ip-mac binding function.
INT swL2IpMacBindingPortIndex	1.3.6.1.4.1.171.11.64.1.2.7.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module).
INT swL2IpMacBindingPortState	1.3.6.1.4.1.171.11.64.1.2.7.1.1.2	INTEGER	read-write	This object enables (strict or loose mode)/disables IP-MAC binding on the specified port. Note: enable-strict (2): SW learning enable-loose (4) : HW learning
INT swL2IpMacBindingPortAllowZeroIp	1.3.6.1.4.1.171.11.64.1.2.7.1.1.3	INTEGER	read-write	This object enables/disables the allow zero IP status on the specified port.
INT swL2IpMacBindingPortForwardDhcpPkt	1.3.6.1.4.1.171.11.64.1.2.7.1.1.4	INTEGER	read-write	This object can be set to forward or not forward DHCP packets on the specified port.
INT swL2IpMacBindingPortDHCPSnoopMaxEntry	1.3.6.1.4.1.171.11.64.1.2.7.1.1.5	INTEGER	read-write	This object indicates the max entry created by DHCP packets on the specified port. Note: When 0 is set on the specified port, the max entry created by DHCP packets is no limit
INT swL2IpMacBindingPortDHCPSnoopEntryClearAction	1.3.6.1.4.1.171.11.64.1.2.7.1.1.6	INTEGER	read-write	When set to start (2), the address binding entries learned for the specified ports will be cleared. When get, it always returns other (1).
INT swL2IpMacBindingPortStopLearningThreshold	1.3.6.1.4.1.171.11.64.1.2.7.1.1.7	INTEGER	read-write	This object indicates the threshold to stop learning new MAC addresses on the specified port. When the number of blocked entries exceeds the threshold, the port will stop learning new addresses. The packet with a new address will be dropped. Note: When 0 is set on the specified port, it means no limit.
INT swL2IpMacBindingPortRecoverLearning	1.3.6.1.4.1.171.11.64.1.2.7.1.1.8	INTEGER	read-write	When set to start (2), it will change the stop_learning state to a normal state on the specified port. When get, it always returns other (1).
INT swL2IpMacBindingPortLearningMode	1.3.6.1.4.1.171.11.64.1.2.7.1.1.9	INTEGER	read-only	When set to Stop(2), it will end the learning state.
swL2IpMacBindingTable	1.3.6.1.4.1.171.11.64.1.2.7.2		not-accessible	This table specifies IP-MAC binding information.
swL2IpMacBindingEntry	1.3.6.1.4.1.171.11.64.1.2.7.2.1		not-accessible	This IP-MAC binding entry is used to add/delete/configure the address pair to the switch's authorized user database.
IP swL2IpMacBindingIpIndex	1.3.6.1.4.1.171.11.64.1.2.7.2.1.1	IpAddress	read-only	The IP address of the IP-MAC binding.
MAC swL2IpMacBindingMac	1.3.6.1.4.1.171.11.64.1.2.7.2.1.2	MacAddress	read-create	The MAC address of the IP-MAC binding.
ROW swL2IpMacBindingStatus	1.3.6.1.4.1.171.11.64.1.2.7.2.1.3	RowStatus	read-create	The status of this entry.
POR swL2IpMacBindingPorts	1.3.6.1.4.1.171.11.64.1.2.7.2.1.4	PortList	read-create	The port members of this entry.
INT swL2IpMacBindingAction	1.3.6.1.4.1.171.11.64.1.2.7.2.1.5	INTEGER	read-only	The action of this entry.
INT swL2IpMacBindingMode	1.3.6.1.4.1.171.11.64.1.2.7.2.1.6	INTEGER	read-create	The mode of this entry. arp: This entry is specified as an ARP mode entry, and this entry will not be added as an access entry. If this object is not specified, the mode defaults to ARP mode. If the system is in ARP mode, the ARP mode entries and ACL mode entries will be effective. If the system is in ACL mode, only the ACL mode entries will be active. acl: This entry is specified as an ACL mode entry. If the user enables the ACL mode, this entry will be added as an access entry. auto: This mode cannot be configured, and when the auto mode is employed, it means this entry is to be learned by DHCP snooping.
swL2IpMacBindingBlockedTable	1.3.6.1.4.1.171.11.64.1.2.7.3		not-accessible	The table specifies information of MAC addresses which were blocked.
swL2IpMacBindingBlockedEntry	1.3.6.1.4.1.171.11.64.1.2.7.3.1		not-accessible	The entry can not create/configure. It can only delete.
VLA swL2IpMacBindingBlockedVID	1.3.6.1.4.1.171.11.64.1.2.7.3.1.1	VlanIndex	read-only	The object specifies the VLAN ID.
MAC swL2IpMacBindingBlockedMac	1.3.6.1.4.1.171.11.64.1.2.7.3.1.2	MacAddress	read-only	The MAC address which was blocked.
STR swL2IpMacBindingBlockedVlanName	1.3.6.1.4.1.171.11.64.1.2.7.3.1.3	DisplayString	read-only	This object specifies the VLAN name.
INT swL2IpMacBindingBlockedPort	1.3.6.1.4.1.171.11.64.1.2.7.3.1.4	INTEGER	read-only	The port with which the MAC is associated.
INT swL2IpMacBindingBlockedType	1.3.6.1.4.1.171.11.64.1.2.7.3.1.5	INTEGER	read-write	The value is always blockByAddrBind. This entry will be deleted by setting the value to delete(3).
INT swL2IpMacBindingAllPortState	1.3.6.1.4.1.171.11.64.1.2.7.4	INTEGER	read-write	This object enables/disables IP-MAC binding on all ports of the system. This action is only applicable when users have write privileges, and can only be viewed when users have read privileges. Note: enable-strict (2): This means strict mode (SW learning). All packets are sent to the CPU. If the user chooses, the port will check ARP packets and IP packets by IP-MAC-PORT Binding entries. If the MAC address can be found or not found by the entry, the MAC will be set as dynamic learned or it will set as blocked, respectively. Other packets will be sent to the CPU and dropped. enable-loose (4) : This means loose mode (HW learning): Only ARP packets and IP broadcast packets will be sent to the CPU. If the user chooses , the port will learn the MAC address on non-ARP and non-IP broadcast packets directly, so these packets will be bypassed. But if the switch receives the ARP or IP broadcast packets and Can not bypass the IP MAC Binding checking, the switch will set this MAC address as blocked and all packets from this MAC address will be dropped.
INT swL2IpMacBindingTrapLogState	1.3.6.1.4.1.171.11.64.1.2.7.5	INTEGER	read-write	when set to enable(2),whenever there's a new MAC that violates the pre-defined Ip Mac Binding configuration, the trap will be sent out and the relevant information will be logged into the system.
INT swL2IpMacBindingACLMode	1.3.6.1.4.1.171.11.64.1.2.7.6	INTEGER	read-write	when set to enable(2), the Ip Mac Binding will use acl mode
INT swL2IpMacBindingDHCPSnoopState	1.3.6.1.4.1.171.11.64.1.2.7.7	INTEGER	read-write	When the dhcp_snoop function is enabled, all address_binding disabled ports will act as DHCP server ports (the switch will learn IP addresses through DHCP server ports (by DHCP OFFER and DHCP ACK packets)). The auto-learned IP-MAC binding entry will be mapped to a specific source port based on the MAC address learning function. This entry will be created as an ACL-mode binding entry for this specific port. Each entry is associated with a lease time. When the lease time expires, the expired entry will be removed from this port. The automatically learned binding entry can be moved from one port to another port if the DHCP snooping function has learned that the MAC address has moved to a different port. Consider a case where DHCP snooping learns a binding entry, and the same IP-MAC binding entry has been statically configured. Suppose that the learned information is consistent with the statically configured entry, then the automatically learned entry will not be created. Suppose the entry is statically configured in ARP mode, since the automatically learned entry will be created in ACL mode, the entry will become ACL mode. Suppose the entry is statically configured on one port and the entry is automatically learned on another port, then both entries will exist. When the dhcp_snoop function is disabled, all of the automatically learned binding entries will be removed.
INT swL2IpMacBindingDHCPSnoopEntryClearAllState	1.3.6.1.4.1.171.11.64.1.2.7.8	INTEGER	read-write	Used to clear all entries created by DHCP packets.
swL2IpMacBindingDHCPSnoopTable	1.3.6.1.4.1.171.11.64.1.2.7.9		not-accessible	The table specifies information regarding the DHCP snooping function learning IP-MAC binding entries.
swL2IpMacBindingDHCPSnoopEntry	1.3.6.1.4.1.171.11.64.1.2.7.9.1		not-accessible	A list of information about the DHCP snooping learning IP-MAC binding entry.
IP swL2IpMacBindingDHCPSnoopIpIndex	1.3.6.1.4.1.171.11.64.1.2.7.9.1.1	IpAddress	read-only	The IP address of this entry.
MAC swL2IpMacBindingDHCPSnoopMac	1.3.6.1.4.1.171.11.64.1.2.7.9.1.2	MacAddress	read-only	The MAC address of this entry.
INT swL2IpMacBindingDHCPSnoopLeaseTime	1.3.6.1.4.1.171.11.64.1.2.7.9.1.3	INTEGER	read-only	Specifies the lease time of this entry. When the lease time expires, this entry will be removed from this port.
INT swL2IpMacBindingDHCPSnoopPort	1.3.6.1.4.1.171.11.64.1.2.7.9.1.4	INTEGER	read-only	Specifies the port of this entry.
INT swL2IpMacBindingDHCPSnoopStatus	1.3.6.1.4.1.171.11.64.1.2.7.9.1.5	INTEGER	read-only	Specifies the status (inactive or active) of this entry.
swL2IpMacBindingPermitIPPoolTable	1.3.6.1.4.1.171.11.64.1.2.7.10		not-accessible	This table specifies the permitted IP pool of IP-MAC binding.
swL2IpMacBindingPermitIPPoolEntry	1.3.6.1.4.1.171.11.64.1.2.7.10.1		not-accessible	A list of information of each permitted IP pool entry.
IP swL2IpMacBindingPermitIPPoolStartIP	1.3.6.1.4.1.171.11.64.1.2.7.10.1.1	IpAddress	read-only	The start IP address of the permitted IP pool.
IP swL2IpMacBindingPermitIPPoolEndIP	1.3.6.1.4.1.171.11.64.1.2.7.10.1.2	IpAddress	read-only	The end IP address of the permitted IP pool.
POR swL2IpMacBindingPermitIPPoolPorts	1.3.6.1.4.1.171.11.64.1.2.7.10.1.3	PortList	read-create	The port members of the permitted IP pool.
ROW swL2IpMacBindingPermitIPPoolStatus	1.3.6.1.4.1.171.11.64.1.2.7.10.1.4	RowStatus	read-create	The status of the permitted IP pool.
INT swL2IpMacBindingARPInspectionState	1.3.6.1.4.1.171.11.64.1.2.7.11	INTEGER	read-write	Used to set ARP inspection state.
swL2TrunkMgmt	1.3.6.1.4.1.171.11.64.1.2.8
INT swL2TrunkMaxSupportedEntries	1.3.6.1.4.1.171.11.64.1.2.8.1	INTEGER	read-only	Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
INT swL2TrunkCurrentNumEntries	1.3.6.1.4.1.171.11.64.1.2.8.2	INTEGER	read-only	Current active number of entries in the trunk configuration table.
swL2TrunkCtrlTable	1.3.6.1.4.1.171.11.64.1.2.8.3		not-accessible	This table specifies which ports are grouped as a set of ports(up to 8) into a single logical link.
swL2TrunkCtrlEntry	1.3.6.1.4.1.171.11.64.1.2.8.3.1		not-accessible	A list of information specifies which ports are grouped as a set of ports(up to 8) into a single logical link.
INT swL2TrunkIndex	1.3.6.1.4.1.171.11.64.1.2.8.3.1.1	INTEGER	read-only	The index of logical port trunk. The trunk group number depends on the existence of the unit and module.
STR swL2TrunkName	1.3.6.1.4.1.171.11.64.1.2.8.3.1.2	DisplayString	read-create	The name of logical port trunk.
INT swL2TrunkMasterPort	1.3.6.1.4.1.171.11.64.1.2.8.3.1.3	INTEGER	read-create	The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swL2TrunkMember	1.3.6.1.4.1.171.11.64.1.2.8.3.1.4	PortList	read-create	Indicates how many ports are included in this Trunk. The trunk port number depends on the existence of module. The maximum number of ports is 8 for one trunks.
INT swL2TrunkFloodingPort	1.3.6.1.4.1.171.11.64.1.2.8.3.1.5	INTEGER	read-only	The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
INT swL2TrunkType	1.3.6.1.4.1.171.11.64.1.2.8.3.1.6	INTEGER	read-create	This object indicates the type of the trunk group. static : is static trunk group lacp : is LACP trunk group .
ROW swL2TrunkState	1.3.6.1.4.1.171.11.64.1.2.8.3.1.7	RowStatus	read-create	This object indicates the status of this entry.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.64.1.2.8.4	INTEGER	read-write	This object configures the part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2MirrorMgmt	1.3.6.1.4.1.171.11.64.1.2.9
INT swL2MirrorLogicTargetPort	1.3.6.1.4.1.171.11.64.1.2.9.1	INTEGER	read-write	This object indicates which port will sniff another port to the switch. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
POR swL2MirrorPortSourceIngress	1.3.6.1.4.1.171.11.64.1.2.9.2	PortList	read-write	This represents the ingress of the source port packet to be sniffed.
POR swL2MirrorPortSourceEgress	1.3.6.1.4.1.171.11.64.1.2.9.3	PortList	read-write	This represents the egress of the source port packet to be sniffed.
INT swL2MirrorPortState	1.3.6.1.4.1.171.11.64.1.2.9.4	INTEGER	read-write	This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disabled(2) - writing this value to the object will remove the corresponding entry from the table. enabled(3) - this entry will reside in the table.
swL2IGMPMgmt	1.3.6.1.4.1.171.11.64.1.2.10
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.11.64.1.2.10.1	INTEGER	read-only	Maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
swL2IGMPCtrlTable	1.3.6.1.4.1.171.11.64.1.2.10.3		not-accessible	This table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If VLAN is in disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.11.64.1.2.10.3.1		not-accessible	The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.11.64.1.2.10.3.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.11.64.1.2.10.3.1.2	INTEGER	read-write	The frequency at which the IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.11.64.1.2.10.3.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.11.64.1.2.10.3.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to have a high loss, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.11.64.1.2.10.3.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPHostTimeout	1.3.6.1.4.1.171.11.64.1.2.10.3.1.6	INTEGER	read-write	The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer has expired. Please reference RFC2236-1997.
INT swL2IGMPRouteTimeout	1.3.6.1.4.1.171.11.64.1.2.10.3.1.7	INTEGER	read-write	The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
INT swL2IGMPLeaveTimer	1.3.6.1.4.1.171.11.64.1.2.10.3.1.8	INTEGER	read-write	When a query receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.11.64.1.2.10.3.1.9	INTEGER	read-write	This object decides if the IGMP query is enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.11.64.1.2.10.3.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.11.64.1.2.10.3.1.11	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.11.64.1.2.10.4		not-accessible	The table contains the current number of IGMP query packets which have been captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.11.64.1.2.10.4.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entires are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.11.64.1.2.10.4.1.1	INTEGER	read-only	This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of the IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.11.64.1.2.10.4.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function has been enabled, on a per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.11.64.1.2.10.4.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increments this object by 1.
swL2IGMPInfoTable	1.3.6.1.4.1.171.11.64.1.2.10.5		not-accessible	The table containing current IGMP information which have been captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entries are all enabled. Note that the priority of IGMP table entries is lower than the Filtering Table, i.e. if there is a table hash collision between the entries of the IGMP Table and the Filtering Table inside the switch H/W address table, the Filtering Table entry will overwrite the colliding entry of the IGMP Table. See swL2FilterMgmt description also.
swL2IGMPInfoEntry	1.3.6.1.4.1.171.11.64.1.2.10.5.1		not-accessible	Information about current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entries are all enabled.
INT swL2IGMPVid	1.3.6.1.4.1.171.11.64.1.2.10.5.1.1	INTEGER	read-only	This object indicates the VID of individual IGMP table entries. It shows the VID of IGMP report information captured on the network.
IP swL2IGMPGroupIpAddr	1.3.6.1.4.1.171.11.64.1.2.10.5.1.2	IpAddress	read-only	This object identifies group ip address which have been captured from the IGMP packet, on a per-Vlan basis.
MAC swL2IGMPMacAddr	1.3.6.1.4.1.171.11.64.1.2.10.5.1.3	MacAddress	read-only	This object identifies mac addresses which correspond to swL2IGMPGroupIpAddr, on a per-Vlan basis.
POR swL2IGMPPortMap	1.3.6.1.4.1.171.11.64.1.2.10.5.1.4	PortList	read-only	This object indicates which ports belong to the same multicast group, on a per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logic port. If the unit has less then 32 port, the other ports don't care and just fill in zero.
INT swL2IGMPIpGroupReportCount	1.3.6.1.4.1.171.11.64.1.2.10.5.1.5	INTEGER	read-only	This object indicates how many report packets were received by the device corresponding with this entry where the IGMP function is enabled, on a per-Vlan basis.
INT swL2IGMPGroupActive	1.3.6.1.4.1.171.11.64.1.2.10.5.1.6	INTEGER	read-only	This object indicates that the entry added the multicast table.
swL2IGMPMulticastVlanTable	1.3.6.1.4.1.171.11.64.1.2.10.6		not-accessible	The information of the IGMP snooping multicast VLAN table.
swL2IGMPMulticastVlanEntry	1.3.6.1.4.1.171.11.64.1.2.10.6.1		not-accessible	The entry of swL2IGMPMulticastVlanTable.
INT swL2IGMPMulticastVlanid	1.3.6.1.4.1.171.11.64.1.2.10.6.1.1	INTEGER	read-only	This object indicates the VLAN id of the IGMP snooping multicast VLAN entry.
STR swL2IGMPMulticastVlanName	1.3.6.1.4.1.171.11.64.1.2.10.6.1.2	SnmpAdminString	read-create	This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
POR swL2IGMPMulticastVlanSourcePort	1.3.6.1.4.1.171.11.64.1.2.10.6.1.3	PortList	read-create	This object indicates the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports would be forwarded to the source ports.
POR swL2IGMPMulticastVlanMemberPort	1.3.6.1.4.1.171.11.64.1.2.10.6.1.4	PortList	read-create	This object indicates the portlist of the member ports of IGMP snooping multicast VLAN. The source ports will be set to untag ports of the vlan entry and the IGMP control messages received from the member ports would be forwarded to the source ports.
ROW swL2IGMPMulticastVlanRowStatus	1.3.6.1.4.1.171.11.64.1.2.10.6.1.5	RowStatus	read-create	This object indicates the status of this entry.
IP swL2IGMPMulticastVlanReplaceSourceIP	1.3.6.1.4.1.171.11.64.1.2.10.6.1.6	IpAddress	read-create	This object is used to replace the source IP address in the IP header for IGMP control packets.
POR swL2IGMPMulticastVlanUntagSourcePort	1.3.6.1.4.1.171.11.64.1.2.10.6.1.7	PortList	read-write	This indicates the untagged member ports to add to the multicast VLAN.
INT swL2IGMPMulticastVlanRemapPriority	1.3.6.1.4.1.171.11.64.1.2.10.6.1.8	INTEGER	read-create	This is the priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to -1, the packet's original priority will be used.
INT swL2IGMPMulticastVlanReplacePriority	1.3.6.1.4.1.171.11.64.1.2.10.6.1.9	INTEGER	read-create	This specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
swL2IGMPRouterPortTable	1.3.6.1.4.1.171.11.64.1.2.10.7		not-accessible	The information of the router port table.
swL2IGMPRouterPortEntry	1.3.6.1.4.1.171.11.64.1.2.10.7.1		not-accessible	The entry of swL2IGMPRouterPortTable.
INT swL2IGMPRouterPortVlanid	1.3.6.1.4.1.171.11.64.1.2.10.7.1.1	INTEGER	read-only	This object indicates the VLAN id of the router port entry.
STR swL2IGMPRouterPortVlanName	1.3.6.1.4.1.171.11.64.1.2.10.7.1.2	SnmpAdminString	read-only	This object indicates the VLAN name of the router port entry.
POR swL2IGMPRouterPortStaticPortList	1.3.6.1.4.1.171.11.64.1.2.10.7.1.3	PortList	read-write	This object indicates the static portlist of the router port entry.
POR swL2IGMPRouterPortDynamicPortList	1.3.6.1.4.1.171.11.64.1.2.10.7.1.4	PortList	read-only	This object indicates the dynamic portlist of the router port entry.
POR swL2IGMPRouterPortForbiddenPortList	1.3.6.1.4.1.171.11.64.1.2.10.7.1.5	PortList	read-write	This object indicates the forbidden portlist of the router port entry.
swL2IGMPAccessAuthTable	1.3.6.1.4.1.171.11.64.1.2.10.8		not-accessible	This table is used to manage the IGMP Access Authentication configurations of the device.
swL2IGMPAccessAuthEntry	1.3.6.1.4.1.171.11.64.1.2.10.8.1		not-accessible	A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
INT swL2IGMPAccessAuthPort	1.3.6.1.4.1.171.11.64.1.2.10.8.1.1	INTEGER	read-only	The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
INT swL2IGMPAccessAuthState	1.3.6.1.4.1.171.11.64.1.2.10.8.1.2	INTEGER	read-write	This object denotes the status of IGMP Access Authentication of the port.
swL2DhcpRelayMgmt	1.3.6.1.4.1.171.11.64.1.2.11
INT swL2DhcpRelayState	1.3.6.1.4.1.171.11.64.1.2.11.1	INTEGER	read-write	This object indicates if the DHCP relay function is enabled or disabled.
INT swL2DhcpRelayHopCount	1.3.6.1.4.1.171.11.64.1.2.11.2	INTEGER	read-write	This object indicates the maximum number of router hops that the DHCP packets can cross.
INT swL2DhcpRelayTimeThreshold	1.3.6.1.4.1.171.11.64.1.2.11.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
INT swL2DhcpRelayOption82State	1.3.6.1.4.1.171.11.64.1.2.11.4	INTEGER	read-write	This object indicates if the DHCP relay agent information option 82 function is enabled or disabled.
INT swL2DhcpRelayOption82Check	1.3.6.1.4.1.171.11.64.1.2.11.5	INTEGER	read-write	This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
INT swL2DhcpRelayOption82Policy	1.3.6.1.4.1.171.11.64.1.2.11.6	INTEGER	read-write	This object indicates the re-forwarding policy is DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option 82 field in messages.
swL2DhcpRelayCtrlTable	1.3.6.1.4.1.171.11.64.1.2.11.7		not-accessible	This table specifies the IP address og the destination to forward (relay) DHCP packets to.
swL2DhcpRelayCtrlEntry	1.3.6.1.4.1.171.11.64.1.2.11.7.1		not-accessible	A list of information specifying the IP address as a destination to forward (relay) DHCP packets to.
STR swL2DhcpRelayCtrlInterfaceName	1.3.6.1.4.1.171.11.64.1.2.11.7.1.1	DisplayString	read-only	The name of the IP interface.
IP swL2DhcpRelayCtrlServer	1.3.6.1.4.1.171.11.64.1.2.11.7.1.2	IpAddress	read-only	The DHCP server IP address.
INT swL2DhcpRelayCtrlState	1.3.6.1.4.1.171.11.64.1.2.11.7.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, results in the corresponding entry being removed from the table. valid(3) - this entry will reside in the table.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.64.1.2.12
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.64.1.2.12.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.64.1.2.12.1.1	INTEGER	read-write	This object indicates the loopback detection status of the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.64.1.2.12.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.64.1.2.12.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. A value of 0 disables the recover function.
INT swL2LoopDetectMode	1.3.6.1.4.1.171.11.64.1.2.12.1.4	INTEGER	read-write	This object indicates the loopback detection mode for the system.
swL2LoopDetectActiveVlan	1.3.6.1.4.1.171.11.64.1.2.12.1.5
OCT swL2LoopDetectActiveVlanRangeList1to64	1.3.6.1.4.1.171.11.64.1.2.12.1.5.1	OCTET STRING	read-only	This object indicates the VLAN range (1-512) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList65to128	1.3.6.1.4.1.171.11.64.1.2.12.1.5.2	OCTET STRING	read-only	This object indicates the VLAN range (513-1024) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList129to192	1.3.6.1.4.1.171.11.64.1.2.12.1.5.3	OCTET STRING	read-only	This object indicates the VLAN range (1025-1536) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList193to256	1.3.6.1.4.1.171.11.64.1.2.12.1.5.4	OCTET STRING	read-only	This object indicates the VLAN range (1537-2048) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList257to320	1.3.6.1.4.1.171.11.64.1.2.12.1.5.5	OCTET STRING	read-only	This object indicates the VLAN range (2049-2560) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList321to384	1.3.6.1.4.1.171.11.64.1.2.12.1.5.6	OCTET STRING	read-only	This object indicates the VLAN range (2561-3072) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList385to448	1.3.6.1.4.1.171.11.64.1.2.12.1.5.7	OCTET STRING	read-only	This object indicates the VLAN range (3073-3584) that added the multicast table.
OCT swL2LoopDetectActiveVlanRangeList449to512	1.3.6.1.4.1.171.11.64.1.2.12.1.5.8	OCTET STRING	read-only	This object indicates the VLAN range (3585-4096) that added the multicast table.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.64.1.2.12.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.64.1.2.12.2.1		not-accessible	The table specifies the loopback detection function specified by the port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.64.1.2.12.2.1.1		not-accessible	The table specifies the loopback detection function specified by the port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
STR swL2LoopDetectPortLoopVLAN	1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.3	DisplayString	read-only	This object indicates the VLAN list that has detected a loopback.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.64.1.2.13
swL2TrafficSegTable	1.3.6.1.4.1.171.11.64.1.2.13.1		not-accessible	This table specifies that the port can just forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.64.1.2.13.1.1		not-accessible	A list of information specifying the port with its traffic forward list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.64.1.2.13.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.64.1.2.13.1.1.2	PortList	read-write	The port list that the specific port can forward traffic to.
swL2PortSecurityMgmt	1.3.6.1.4.1.171.11.64.1.2.14
swL2PortSecurityControlTable	1.3.6.1.4.1.171.11.64.1.2.14.1		not-accessible	port security feature which controls the address learning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reaches N, any incoming packet that has not learned a source addresses is discarded (e.g. dropped) and no more new addresses can be learned on this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.11.64.1.2.14.1.1		not-accessible	A list of information contained in swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.11.64.1.2.14.1.1.1	INTEGER	read-only	Indicates the secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.11.64.1.2.14.1.1.2	INTEGER	read-write	Indicates allowable number of addresses to be learned at this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.11.64.1.2.14.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer has expired. In this mode, when the locked address has aged out, the number of addresses that can be learned has to increase by one. In deleteOnReset(4) mode - never age out the locked addresses unless restarting the system to prevent from port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.11.64.1.2.14.1.1.4	INTEGER	read-write	Indicates the administration state of the locking address.
INT swL2PortSecurityTrapLogState	1.3.6.1.4.1.171.11.64.1.2.14.2	INTEGER	read-write	when enable(2)is selected,whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in system.
swL2PortSecurityDelCtrl	1.3.6.1.4.1.171.11.64.1.2.14.3
STR swL2PortSecurityDelVlanName	1.3.6.1.4.1.171.11.64.1.2.14.3.1	DisplayString	read-write	Indicates VLAN name.
INT swL2PortSecurityDelPort	1.3.6.1.4.1.171.11.64.1.2.14.3.2	INTEGER	read-write	Indicates the port.
MAC swL2PortSecurityDelMacAddress	1.3.6.1.4.1.171.11.64.1.2.14.3.3	MacAddress	read-write	Specifies a MAC address.
INT swL2PortSecurityDelActivity	1.3.6.1.4.1.171.11.64.1.2.14.3.4	INTEGER	read-write	.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.64.1.2.15
swL2MgmtMIBTrapPrefix	1.3.6.1.4.1.171.11.64.1.2.15.0
NTF swL2macNotification	1.3.6.1.4.1.171.11.64.1.2.15.0.3			This trap indicate the MAC addresses variation in the address table .
NTF swL2porttypechgNotification	1.3.6.1.4.1.171.11.64.1.2.15.0.4			This trap indicates the port type change.
NTF swPowerStatusChg	1.3.6.1.4.1.171.11.64.1.2.15.0.5			Power Status change notification. The notification is issued when the swPowerStatus changes as in the following cases: lowVoltage -> overCurrent. lowVoltage -> working. lowVoltage -> disconnect. lowVoltage -> connect. overCurrent -> lowVoltage. overCurrent -> working. overCurrent -> disconnect. overCurrent -> connect. working -> lowVoltage. working -> overCurrent. working -> connect. working -> disconnect. fail -> connect. fail -> disconnect. connect -> lowVoltage. connect -> overCurrent. connect -> working. connect -> disconnect. disconnect -> lowVoltage. disconnect -> overCurrent. disconnect -> working. disconnect -> connect.
NTF swPowerFailure	1.3.6.1.4.1.171.11.64.1.2.15.0.6			Power Failure notification. The notification issues when the swPowerStatus changes as in the following cases: lowVoltage -> fail. overCurrent -> fail. working -> fail. connect -> fail. disconnect -> fail.
NTF swPowerRecover	1.3.6.1.4.1.171.11.64.1.2.15.0.7			Power Recover notification. The notification issues when the swPowerStatus changes as in the following cases: fail -> lowVoltage. fail -> overCurrent. fail -> working.
NTF swL2PortSecurityViolationTrap	1.3.6.1.4.1.171.11.64.1.2.15.0.8			When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration a trap will be sent out
NTF swL2IpMacBindingViolationTrap	1.3.6.1.4.1.171.11.64.1.2.15.0.9			When the IP-Mac Binding trap is enabled, if there's a new MAC that violates the pre-defined port security configuration a trap will be sent out
NTF swL2IpMacBindingStopLearningTrap	1.3.6.1.4.1.171.11.64.1.2.15.0.10			When the IP-MAC Binding trap is enabled, if the specific port changes from a normal state to a stop_learning state, a trap will be sent out.
NTF swL2IpMacBindingRecoverLearningTrap	1.3.6.1.4.1.171.11.64.1.2.15.0.11			When the IP-MAC Binding trap is enabled, if the specific port changes from a stop_learning state to a normal state, a trap will be sent out.
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.11.64.1.2.15.0.12			The trap is sent when a Port loop occurs.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.11.64.1.2.15.0.13			The trap is sent when a Port loop restarts after the interval time.
NTF swL2VlanLoopOccurred	1.3.6.1.4.1.171.11.64.1.2.15.0.14			The trap is sent when a Port with a VID loop occurs.
NTF swL2VlanLoopRestart	1.3.6.1.4.1.171.11.64.1.2.15.0.15			The trap is sent when a Port with a VID loop restarts after the interval time.
swl2NotificationBidings	1.3.6.1.4.1.171.11.64.1.2.15.1
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.64.1.2.15.1.1	OCTET STRING	read-only	This object indicates information about the last time the system rebooted.
swl2NotifyPortSecurity	1.3.6.1.4.1.171.11.64.1.2.15.2
MAC swL2PortSecurityViolationMac	1.3.6.1.4.1.171.11.64.1.2.15.2.1	MacAddress	accessible-for-notify	This object indicates the MAC address that violated the port security configuration.
swl2NotifyIpMacBinding	1.3.6.1.4.1.171.11.64.1.2.15.3
MAC swL2IpMacBindingViolationIP	1.3.6.1.4.1.171.11.64.1.2.15.3.1	MacAddress	accessible-for-notify	This object indicates the MAC address that violates the IP-Mac Binging configuration.
MAC swL2IpMacBindingViolationMac	1.3.6.1.4.1.171.11.64.1.2.15.3.2	MacAddress	accessible-for-notify	This object indicates the IP address that violates the IP-Mac Binging configuration.
swl2NotifyLoopDetect	1.3.6.1.4.1.171.11.64.1.2.15.4
INT swL2VlanLoopDetectVID	1.3.6.1.4.1.171.11.64.1.2.15.4.1	INTEGER	accessible-for-notify	This object indicates the VID that has detected a loopback.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.11.64.1.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.11.64.1.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.11.64.1.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.11.64.1.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.11.64.1.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.11.64.1.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.
swL2DhcpLocalRelayOption82Table	1.3.6.1.4.1.171.11.64.1.2.24.3		not-accessible	This table is used to manage the DHCP local relay option 82 policy for each port.
swL2DhcpLocalRelayOption82Entry	1.3.6.1.4.1.171.11.64.1.2.24.3.1		not-accessible	This object lists the current ports in the switch and their corresponding DHCP local relay option 82 policy.
INT swL2DhcpLocalRelayOption82PortIndex	1.3.6.1.4.1.171.11.64.1.2.24.3.1.1	INTEGER	not-accessible	This object indicates the module's port number.(1..Max port number in the module)
INT swL2DhcpLocalRelayOption82Policy	1.3.6.1.4.1.171.11.64.1.2.24.3.1.2	INTEGER	read-write	This object indicates the policy of the DHCP local relay option 82 of each port.
INT swL2DhcpLocalRelayOption82RemoteIDType	1.3.6.1.4.1.171.11.64.1.2.24.4	INTEGER	read-write	This object indicates the type of remote ID for DHCP Local Relay. If the type is default, the remote ID will be the MAC address of the device. If the type is user-defined, the remote ID can be defined by writing to the swL2DhcpLocalRelayOption82RemoteID object.
STR swL2DhcpLocalRelayOption82RemoteID	1.3.6.1.4.1.171.11.64.1.2.24.5	DisplayString	read-write	This object displays the current remote ID of the device for DHCP Local Relay. If swL2DhcpRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swL2DhcpRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.
swL2PPPoEMgmt	1.3.6.1.4.1.171.11.64.1.2.25
INT swL2PPPoECirIDinsertState	1.3.6.1.4.1.171.11.64.1.2.25.1	INTEGER	read-write	This object indicates the status of the PPPoE circuit ID insertion state of the switch.

RFC description

D-Link DES3526 Layer 2 management for VLAN, IGMP, and switching features.

Start monitoring D-Link DES-3526 managed switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3526-L2MGMT-MIB

What Is DES3526-L2MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description