All MIBs › DGS3426-L3MGMT-MIB
Last Updated: 2008-09-22
Category: Technology: Routing/L3, Vendor: D-Link
Description: L3 management MIB for D-Link DGS-3426 switch covering routing protocols, ACLs, VRRP, and Layer 3 management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DGS3426-L3MGMT-MIB?
DGS3426-L3MGMT-MIB is a vendor-specific MIB from D-Link scoped to Layer 3 management on the DGS-3426 switch, covering routing-protocol control, IP interface configuration, ARP/FDB information, static routing, and IPv6 interface settings. Its swL3IpCtrlTable configures per-interface objects such as swL3IpCtrlIpAddr/IpSubnetMask, swL3IpCtrlVlanName, swL3IpCtrlProxyArp, and swL3IpCtrlAdminState, with a parallel swL3Ipv6CtrlTable and swL3Ipv6AddressCtrlTable handling IPv6 router-advertisement timers and address lifetimes, plus DHCPv6 prefix-delegation objects. A swL3IpFdbInfoTable exposes the Layer 3 forwarding-database entries (IP address, subnet mask, port, entry type) learned or configured on the switch, and swL3IpStaticRouteTable manages static routes with destination, mask, next hop, metric, and RowStatus-based lifecycle control, alongside a top-level swL3DevCtrlRIPState scalar for enabling RIP. This makes it a broad Layer 3 configuration/state MIB useful for confirming IP interface, static-route, and RIP configuration match intent on a routing-capable D-Link switch. The DGS3426-L3MGMT-MIB MIB is deployed on D-Link DGS-3426 Layer 3 switches in campus/enterprise networks.
IPNetwork Monitor allows you to monitor SNMP objects defined in DGS3426-L3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link DGS-3426 Layer 3 switches
Monitoring Examples
An operator walks swL3IpStaticRouteTable to confirm a critical static route's swL3IpStaticRouteStatus is active and its swL3IpStaticRouteNextHop matches the intended gateway; a route present with swL3IpStaticRouteStatus showing notInService would explain traffic silently falling back to a default route or being blackholed.
What Can Be Monitored
- per-interface IP address/subnet/VLAN configuration
- IPv6 interface and address lifetime configuration
- Layer 3 forwarding-database (ARP/FDB) entries
- static route table entries and status
- RIP protocol admin state
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| PhysAddress | |
| RowStatus | |
| TimeStamp | |
| TruthValue |
From SW34XXPRIMGMT-MIB
| dgs3426 | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| swL3MgmtMIB | 1.3.6.1.4.1.171.11.70.1.3 | The Structure of Layer 3 Network Management Information for the proprietary enterprise. | ||
| swL3DevMgmt | 1.3.6.1.4.1.171.11.70.1.3.1 | |||
| swL3DevCtrl | 1.3.6.1.4.1.171.11.70.1.3.1.1 | |||
| INT swL3DevCtrlRIPState | 1.3.6.1.4.1.171.11.70.1.3.1.1.1 | INTEGER | read-write | This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled. |
| swL3IpMgmt | 1.3.6.1.4.1.171.11.70.1.3.2 | |||
| swL3IpCtrlMgmt | 1.3.6.1.4.1.171.11.70.1.3.2.1 | |||
| swL3IpCtrlTable | 1.3.6.1.4.1.171.11.70.1.3.2.1.3 | not-accessible | This table contain IP interface information. | |
| swL3IpCtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1 | not-accessible | A list of information about a specific IP interface. | |
| STR swL3IpCtrlInterfaceName | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| INT swL3IpCtrlIfIndex | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.2 | INTEGER | read-only | This object uniquely identifies the IP interface number in the swL3IpCtrlTable. |
| IP swL3IpCtrlIpAddr | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.3 | IpAddress | read-write | The IP address of the interface. This object only can take the value of the unicast IP address. |
| IP swL3IpCtrlIpSubnetMask | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.4 | IpAddress | read-write | The IP net mask for this interface. |
| STR swL3IpCtrlVlanName | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.5 | DisplayString | read-write | This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table. |
| INT swL3IpCtrlProxyArp | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.6 | INTEGER | read-write | This object indicates enable/disable of the proxy ARP function for IPv4. |
| T/F swL3IpCtrlSecondary | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.7 | TruthValue | read-write | When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP. |
| INT swL3IpCtrlMode | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.8 | INTEGER | read-write | This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server. |
| INT swL3IpCtrlAdminState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.9 | INTEGER | read-write | The state of the IP interface. |
| ADR swL3IpCtrlIpv6LinkLocalAddress | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.14 | Ipv6Address | read-only | The IPv6 link local address for this interface. |
| INT swL3IpCtrlIpv6LinkLocalPrefixLen | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.15 | INTEGER | read-only | The IPv6 prefix length for this IPv6 link local address. |
| ROW swL3IpCtrlState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.16 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| INT swL3IpCtrlIpv6LinkLocalAutoState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.17 | INTEGER | read-write | The state of the IPv6 link local auto. |
| INT swL3IpCtrlLocalProxyArp | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.18 | INTEGER | read-create | If the state is enabled, the switch will be allowed to respond to the proxy ARP proxy ARP when the source IP and destination IP are on the same interface. |
| INT swL3IpCtrlDhcpv6ClientState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.20 | INTEGER | read-write | The state of the Dhcpv6 Client. |
| INT swL3IpCtrlIpDirectedBroadcastState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.21 | INTEGER | read-write | The state of the IP Directed Broadcast. |
| INT swL3IpCtrlIpDhcpOption12State | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.22 | INTEGER | read-write | Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message. |
| STR swL3IpCtrlIpDhcpOption12HostName | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.23 | DisplayString | read-write | Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12. |
| INT swL3IpCtrlDhcpv6ClientPDState | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.24 | INTEGER | read-write | The state of the Dhcpv6 Client PD. |
| STR swL3IpCtrlDhcpv6ClientPDPrefixName | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.25 | DisplayString | read-write | This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write. |
| ADR swL3IpCtrlDhcpv6ClientPDPrefix | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.26 | Ipv6Address | read-only | The IPv6 prefix obtained form delegation router. |
| INT swL3IpCtrlDhcpv6ClientPDPrefixLen | 1.3.6.1.4.1.171.11.70.1.3.2.1.3.1.27 | INTEGER | read-only | The IPv6 prefix length for the prefix obtained from delegation router. |
| swL3Ipv6CtrlTable | 1.3.6.1.4.1.171.11.70.1.3.2.1.4 | not-accessible | This table contains IPv6 information of an IP interface. | |
| swL3Ipv6CtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1 | not-accessible | A list of IPv6 information about a specific IP interface. | |
| STR swL3Ipv6CtrlInterfaceName | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| INT swL3Ipv6CtrlMaxReassmblySize | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.2 | INTEGER | read-only | Maximum Reassembly Size of the IP interface. |
| U32 swL3Ipv6CtrlNsRetransTimer | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.3 | Unsigned32 | read-write | Neighbor solicitation's retransmit timer. The unit is set in milliseconds. |
| INT swL3Ipv6CtrlRaState | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.5 | INTEGER | read-write | Neighbor solicited state. |
| INT swL3Ipv6CtrlRaMinRtrAdvInterval | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.6 | INTEGER | read-write | The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval |
| INT swL3Ipv6CtrlRaMaxRtrAdvInterval | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.7 | INTEGER | read-write | The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. |
| INT swL3Ipv6CtrlRaLifeTime | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.8 | INTEGER | read-write | Indicates the lifetime of the router as the default router. |
| INT swL3Ipv6CtrlRaReachableTime | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.9 | INTEGER | read-write | Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation. |
| U32 swL3Ipv6CtrlRaRetransTime | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.10 | Unsigned32 | read-write | Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond. |
| INT swL3Ipv6CtrlRaHopLimit | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.11 | INTEGER | read-write | Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message. |
| INT swL3Ipv6CtrlRaManagedFlag | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.12 | INTEGER | read-write | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration. |
| INT swL3Ipv6CtrlRaOtherConfigFlag | 1.3.6.1.4.1.171.11.70.1.3.2.1.4.1.13 | INTEGER | read-write | When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information. |
| swL3Ipv6AddressCtrlTable | 1.3.6.1.4.1.171.11.70.1.3.2.1.5 | not-accessible | This table contain IPv6 address information for each IP interface. | |
| swL3Ipv6AddressCtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1 | not-accessible | A list of information about a specific IPv6 address. | |
| STR swL3Ipv6AddressCtrlInterfaceName | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| ADR swL3Ipv6Address | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.2 | Ipv6Address | read-only | Specify the IPv6 address. |
| INT swL3Ipv6AddressCtrlPrefixLen | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.3 | INTEGER | read-only | Indicates the prefix length of this IPv6 address. |
| U32 swL3Ipv6AddressCtrlPreferredLifeTime | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.4 | Unsigned32 | read-write | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff. |
| U32 swL3Ipv6AddressCtrlValidLifeTime | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.5 | Unsigned32 | read-write | Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff. |
| INT swL3Ipv6AddressCtrlOnLinkFlag | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.6 | INTEGER | read-write | When enabled, the address implied by the specified prefix is available on the link where the RA message is received. |
| INT swL3Ipv6AddressCtrlAutonomousFlag | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.7 | INTEGER | read-write | When enabled, the specified prefix will be used to create an autonomous address configuration. |
| ROW swL3Ipv6AddressCtrlState | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.8 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table. |
| INT swL3Ipv6AddressCtrlAddressType | 1.3.6.1.4.1.171.11.70.1.3.2.1.5.1.9 | INTEGER | read-only | This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement. |
| swL3Ipv6DHCPv6CPDAddrCtrlTable | 1.3.6.1.4.1.171.11.70.1.3.2.1.6 | not-accessible | This table contain the information of the IPv6 address which based on DHCPv6 client PD. | |
| swL3Ipv6DHCPv6CPDAddrCtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1 | not-accessible | A list of information about a specific DHCPv6 Client PD IPv6 address. | |
| STR swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| STR swL3Ipv6DHCPv6CPDAddrCtrlPrefixName | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1.2 | DisplayString | read-only | This object indicates the name of the prefix based on which the IPv6 address will be generate. |
| ADR swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1.3 | Ipv6Address | read-only | Specify the suffix of the IPv6 address. |
| INT swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1.4 | INTEGER | read-only | Indicates the prefix length of this IPv6 address. |
| ROW swL3Ipv6DHCPv6CPDAddrCtrlState | 1.3.6.1.4.1.171.11.70.1.3.2.1.6.1.5 | RowStatus | read-create | This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table. |
| INT swL3IpCtrlAllIpIfState | 1.3.6.1.4.1.171.11.70.1.3.2.1.7 | INTEGER | read-write | This object indicates all interface function state of the device. |
| swL3IpFdbMgmt | 1.3.6.1.4.1.171.11.70.1.3.2.2 | |||
| swL3IpFdbInfoTable | 1.3.6.1.4.1.171.11.70.1.3.2.2.1 | not-accessible | A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets. | |
| swL3IpFdbInfoEntry | 1.3.6.1.4.1.171.11.70.1.3.2.2.1.1 | not-accessible | Information about a specific IP address for which the bridge has some forwarding and/or filtering information. | |
| IP swL3IpFdbInfoIpAddr | 1.3.6.1.4.1.171.11.70.1.3.2.2.1.1.1 | IpAddress | read-only | A IP address for which switch has forwarding and/or filtering information. |
| IP swL3IpFdbInfoIpSubnetMask | 1.3.6.1.4.1.171.11.70.1.3.2.2.1.1.2 | IpAddress | read-only | A IP net mask for this interface.for which switch has forwarding and/or filtering information. |
| INT swL3IpFdbInfoPort | 1.3.6.1.4.1.171.11.70.1.3.2.2.1.1.3 | INTEGER | read-only | Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address. |
| INT swL3IpFdbInfoType | 1.3.6.1.4.1.171.11.70.1.3.2.2.1.1.4 | INTEGER | read-only | The status of this entry. |
| INT swL3IpArpAgingTime | 1.3.6.1.4.1.171.11.70.1.3.2.4 | INTEGER | read-write | The timeout period in minutes for aging out dynamically learned arp information. |
| swL3IpStaticRouteTable | 1.3.6.1.4.1.171.11.70.1.3.2.5 | not-accessible | This entity's IP static Routing table. | |
| swL3IpStaticRouteEntry | 1.3.6.1.4.1.171.11.70.1.3.2.5.1 | not-accessible | A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action. | |
| IP swL3IpStaticRouteDest | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.1 | IpAddress | read-only | The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x. |
| IP swL3IpStaticRouteMask | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.2 | IpAddress | read-only | Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest. |
| INT swL3IpStaticRouteBkupState | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.3 | INTEGER | read-only | The routing state for this route.The value SHOULD be primary(1) or backup(2). |
| IP swL3IpStaticRouteNextHop | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.4 | IpAddress | read-create | On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0. |
| INT swL3IpStaticRouteMetric | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.5 | INTEGER | read-create | The routing metric for this route. |
| INT swL3IpStaticRouteStatus | 1.3.6.1.4.1.171.11.70.1.3.2.5.1.6 | INTEGER | read-create | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table. |
| swL3RelayMgmt | 1.3.6.1.4.1.171.11.70.1.3.3 | |||
| swL3RelayDhcpMgmt | 1.3.6.1.4.1.171.11.70.1.3.3.1 | |||
| INT swL3RelayDhcpState | 1.3.6.1.4.1.171.11.70.1.3.3.1.1 | INTEGER | read-write | This object indicates Dhcp Relay function is enabled or disabled. |
| INT swL3RelayDhcpHopCount | 1.3.6.1.4.1.171.11.70.1.3.3.1.2 | INTEGER | read-write | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| INT swL3RelayDhcpTimeThreshold | 1.3.6.1.4.1.171.11.70.1.3.3.1.3 | INTEGER | read-write | This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet. |
| swL3RelayDhcpCtrlTable | 1.3.6.1.4.1.171.11.70.1.3.3.1.4 | not-accessible | This table specifys the IP address as a destination to forward (relay) DHCP packets to. | |
| swL3RelayDhcpCtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.3.1.4.1 | not-accessible | A list of information specifies the IP address as a destination to forward (relay) DHCP packets to. | |
| STR swL3RelayDhcpCtrlInterfaceName | 1.3.6.1.4.1.171.11.70.1.3.3.1.4.1.1 | DisplayString | read-only | The name of the IP interface. |
| IP swL3RelayDhcpCtrlServer | 1.3.6.1.4.1.171.11.70.1.3.3.1.4.1.2 | IpAddress | read-only | The DHCP server IP address. |
| INT swL3RelayDhcpCtrlState | 1.3.6.1.4.1.171.11.70.1.3.3.1.4.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| INT swL3RelayDhcpOption82State | 1.3.6.1.4.1.171.11.70.1.3.3.1.5 | INTEGER | read-write | This object indicates DHCP Relay Option 82 function is enabled or disabled. |
| INT swL3RelayDhcpOption82CheckState | 1.3.6.1.4.1.171.11.70.1.3.3.1.6 | INTEGER | read-write | This object indicates DHCP Relay Option 82 Check function is enabled or disabled. |
| INT swL3RelayDhcpOption82Policy | 1.3.6.1.4.1.171.11.70.1.3.3.1.7 | INTEGER | read-write | This object indicates DHCP Relay Option 82 Policy. |
| swL3DHCPRelayOption60 | 1.3.6.1.4.1.171.11.70.1.3.3.1.8 | |||
| INT swL3DHCPRelayOption60State | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.1 | INTEGER | read-write | This object indicates DHCP relay option 60 function is enabled or disabled. |
| INT swL3DHCPRelayOption60DefMode | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.2 | INTEGER | read-write | This object indicates default mode that has no option 60 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption60DefRelayIp. drop(2): means to drop the packet. |
| swL3DHCPRelayOption60DefTable | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.3 | not-accessible | This table indicates the default relay servers for the packet that has no option 60 mathcing rules. | |
| swL3DHCPRelayOption60DefEntry | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.3.1 | not-accessible | A list of information indicates the default relay servers for the packet that has no option 60 mathcing rules. | |
| IP swL3DHCPRelayOption60DefRelayIp | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.3.1.1 | IpAddress | read-only | This object indicates the IP address of default relay server. |
| ROW swL3DHCPRelayOption60DefRowStatus | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.3.1.2 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3DHCPRelayOption60Table | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4 | not-accessible | This table indicates the relay servers for the packet at option 60 rules. | |
| swL3DHCPRelayOption60Entry | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4.1 | not-accessible | A list of information indicates the relay servers for the packet at option 60 rules. | |
| STR swL3DHCPRelayOption60String | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4.1.1 | DisplayString | read-only | This object indicates string of this entry. Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string. |
| IP swL3DHCPRelayOption60RelayIp | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4.1.2 | IpAddress | read-only | This object indicates the IP address of relay server. |
| INT swL3DHCPRelayOption60MatchType | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4.1.3 | INTEGER | read-create | This object indicates match state of this entry. exact(1): means the option 60 string in the packet must full match with the specified string. partial(2): means the option 60 string in the packet only need partial match with the specified string. |
| ROW swL3DHCPRelayOption60RowStatus | 1.3.6.1.4.1.171.11.70.1.3.3.1.8.4.1.4 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3DHCPRelayOption61 | 1.3.6.1.4.1.171.11.70.1.3.3.1.9 | |||
| INT swL3DHCPRelayOption61State | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.1 | INTEGER | read-write | This object indicates DHCP relay option 61 function is enabled or disabled. |
| INT swL3DHCPRelayOption61DefMode | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.2 | INTEGER | read-write | This object indicates default mode that has no option 61 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61DefRelayIp. drop(2): means to drop the packet. |
| IP swL3DHCPRelayOption61DefRelayIp | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.3 | IpAddress | read-write | This object indicates the IP address of default relay server that has no option 61 mathcing rules. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'. |
| swL3DHCPRelayOption61Table | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4 | not-accessible | This table indicates the relay servers for the packet at option 61 rules. | |
| swL3DHCPRelayOption61Entry | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1 | not-accessible | A list of information indicates the relay servers for the packet at option 61 rules. | |
| INT swL3DHCPRelayOption61ClientType | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1.1 | INTEGER | read-only | This object indicates client type of this entry. mac(1): means the client-ID which is the MAC address of client. string(2): means the client-ID which is specified string by administrator. |
| STR swL3DHCPRelayOption61ClientID | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1.2 | DisplayString | read-only | This object indicates string of this entry. When swL3DHCPRelayOption61ClientType is mac(1), the format of this object should be XX-XX-XX-XX-XX-XX (MAC address). Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string. |
| INT swL3DHCPRelayOption61Mode | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1.3 | INTEGER | read-create | This object indicates mode of this entry. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61RelayIp. drop(2): means to drop the packet. |
| IP swL3DHCPRelayOption61RelayIp | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1.4 | IpAddress | read-create | This object indicates the IP address of relay server. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'. |
| ROW swL3DHCPRelayOption61RowStatus | 1.3.6.1.4.1.171.11.70.1.3.3.1.9.4.1.5 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3RelayDnsMgmt | 1.3.6.1.4.1.171.11.70.1.3.3.2 | |||
| INT swL3RelayDnsState | 1.3.6.1.4.1.171.11.70.1.3.3.2.1 | INTEGER | read-write | This object indicates DNS Relay function is enabled or disabled. |
| IP swL3RelayDnsPrimaryServer | 1.3.6.1.4.1.171.11.70.1.3.3.2.2 | IpAddress | read-write | This object indicates the address of the primary DNS server. |
| IP swL3RelayDnsSecondaryServer | 1.3.6.1.4.1.171.11.70.1.3.3.2.3 | IpAddress | read-write | This object indicates the address of the secondary DNS server. |
| INT swL3RelayDnsCacheState | 1.3.6.1.4.1.171.11.70.1.3.3.2.4 | INTEGER | read-write | This object indicates DNS Relay cache is enabled or disabled. |
| INT swL3RelayDnsStaticTableState | 1.3.6.1.4.1.171.11.70.1.3.3.2.5 | INTEGER | read-write | This object indicates DNS Relay static table is enabled or disabled. |
| swL3RelayDnsCtrlTable | 1.3.6.1.4.1.171.11.70.1.3.3.2.6 | not-accessible | This table display the current DNS relay static table. | |
| swL3RelayDnsCtrlEntry | 1.3.6.1.4.1.171.11.70.1.3.3.2.6.1 | not-accessible | A list of information display the current DNS relay static table. | |
| STR swL3RelayDnsCtrlDomainName | 1.3.6.1.4.1.171.11.70.1.3.3.2.6.1.1 | DisplayString | read-only | The domain name of the entry. |
| IP swL3RelayDnsCtrlIpAddr | 1.3.6.1.4.1.171.11.70.1.3.3.2.6.1.2 | IpAddress | read-only | The IP address of the entry. |
| INT swL3RelayDnsCtrlState | 1.3.6.1.4.1.171.11.70.1.3.3.2.6.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3RouteRedistriTable | 1.3.6.1.4.1.171.11.70.1.3.5 | not-accessible | Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol. | |
| swL3RouteRedistriEntry | 1.3.6.1.4.1.171.11.70.1.3.5.1 | not-accessible | A list of information displaying the route redistribution table. | |
| INT swL3RouteRedistriSrcProtocol | 1.3.6.1.4.1.171.11.70.1.3.5.1.1 | INTEGER | read-only | Allows the selection of the protocol of the source device. |
| INT swL3RouteRedistriDstProtocol | 1.3.6.1.4.1.171.11.70.1.3.5.1.2 | INTEGER | read-only | Allows the selection of the protocol of the destination device. |
| INT swL3RouteRedistriMetric | 1.3.6.1.4.1.171.11.70.1.3.5.1.4 | INTEGER | read-create | Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value. |
| ROW swL3RouteRedistriRowStatus | 1.3.6.1.4.1.171.11.70.1.3.5.1.5 | RowStatus | read-create | This object indicates the status of this entry. |
| swL3RoutePreference | 1.3.6.1.4.1.171.11.70.1.3.9 | |||
| INT swL3RoutePreferenceRIP | 1.3.6.1.4.1.171.11.70.1.3.9.1 | INTEGER | read-write | Used to configure the route preference of RIP. |
| INT swL3RoutePreferenceStatic | 1.3.6.1.4.1.171.11.70.1.3.9.3 | INTEGER | read-write | Used to configure the route preference of Static. |
| INT swL3RoutePreferenceLocal | 1.3.6.1.4.1.171.11.70.1.3.9.4 | INTEGER | read-only | Used to read the route preference of Local. |
| INT swL3RoutePreferenceDefault | 1.3.6.1.4.1.171.11.70.1.3.9.8 | INTEGER | read-write | Used to configure the route preference of Default. |
RFC description
Provides Layer 3 network management information for D-Link DGS3426 switches, including IP routing and relay management.
Start monitoring D-Link DGS-3426 Layer 3 switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.