DEVTRAPS-MIB

All MIBs › DEVTRAPS-MIB

Organization: Aperto Networks

Last Updated: 2001-05-09

Category: Alarm and Event Management

Description: Defines SNMP trap notifications for operational events on network devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DEVTRAPS-MIB?

DEVTRAPS-MIB is a vendor-specific MIB defining SNMP trap notifications for operational events on the BSU/SU (Base Station Unit / Subscriber Unit) wireless broadband product family. It exposes a trap-control object and a set of trap notification definitions rather than polled runtime tables, allowing an NMS to be alerted asynchronously to significant device events. Its monitoring role centers on fault and event notification, letting an administrator enable or disable trap generation via aniDevControlTrapGeneration and receive real-time alerts about operational events on the device (complementing the polled data in the sibling DEVBASE/DEVETHERNET/DEVCONTROL/DEVSERVER MIBs), which is effectively a software/operational-status signal for the unit. It depends conceptually on the SNMPv2 notification framework (SNMPv2-TRAP-PMIB conventions) and works alongside the other 'ani' device MIBs in the same family. It is typically deployed on BSU/SU wireless units where an NMS needs push notifications from the DEVTRAPS-MIB MIB rather than only periodic polling.

IPNetwork Monitor allows you to monitor SNMP objects defined in DEVTRAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

fixed wireless Base Station Unit (BSU)
fixed wireless Subscriber Unit (SU)

Monitoring Examples

An administrator would set aniDevControlTrapGeneration to enable trap generation on a unit, then configure the NMS to listen for the aniDevTraps notifications defined by this MIB to be alerted immediately when a significant device event occurs, such as a reset or configuration change, rather than waiting for the next poll cycle. aniDevTrapControl provides finer-grained control over which trap types are active. Because the available detail is limited to these control and top-level trap objects, specific per-event trap varbind contents are not enumerated here.

What Can Be Monitored

trap generation enable/disable state
trap type control settings
asynchronous operational event notifications

Imported Objects

From ANIROOT-MIB

device

OBJECT-IDENTITY

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
aniDevTrap	1.3.6.1.4.1.4325.2.10			The trap group.
aniDevTraps	1.3.6.1.4.1.4325.2.10.0
NTF aniDevTrapSuSyncAcquired	1.3.6.1.4.1.4325.2.10.0.1			This trap is generated by LKAD when SYNC is acquired.
NTF aniDevTrapBsuSuUp	1.3.6.1.4.1.4325.2.10.0.2			This trap is sent out by BSU to report that SU is operational.
NTF aniDevTrapBsuSuDown	1.3.6.1.4.1.4325.2.10.0.3			This trap is sent out by BSU to report that SU is down.
NTF aniDevTrapSuBsuUp	1.3.6.1.4.1.4325.2.10.0.4			This trap is sent out by SU to report that BSU is operational.
NTF aniDevTrapSuBsuDown	1.3.6.1.4.1.4325.2.10.0.5			This trap is sent out by SU to report that BSU is down.
NTF aniDevTrapDhcpFailure	1.3.6.1.4.1.4325.2.10.0.6			This trap is generated when DHCP fails.
NTF aniDevTrapConfigDownloadFailure	1.3.6.1.4.1.4325.2.10.0.7			This trap is generated when Config file download fails.
NTF aniDevTrapRamTooLow	1.3.6.1.4.1.4325.2.10.0.8			This trap is sent out to indicate that the RAM is too low.
NTF aniDevTrapRamNormal	1.3.6.1.4.1.4325.2.10.0.9			This trap is sent out to indicate that the RAM available is normal. This trap is sent out to indicate that the aniDevTrapRamTooLow alarm is cleared.
NTF aniDevTrapModemPllNotLocked	1.3.6.1.4.1.4325.2.10.0.10			The Modem PLL (Phase Locked Loop) not locked trap.
NTF aniDevTrapModemPllNotLockedClear	1.3.6.1.4.1.4325.2.10.0.11			The Modem PLL (Phase Locked Loop) not locked trap cleared. This trap is sent out to indicate that the aniDevTrapModemPllNotLocked alarm is cleared.
NTF aniDevTrapRadioVoltReg	1.3.6.1.4.1.4325.2.10.0.12			This trap indicates a Radio Voltage Failure. It is sent out by both BSU and SU.
NTF aniDevTrapRadioVoltRegClear	1.3.6.1.4.1.4325.2.10.0.13			This trap is sent out when aniDevTrapRadioVoltReg (Radio Voltage Failure) alarm is cleared. It is sent out by both BSU and SU.
NTF aniDevTrapRadioSynthNotLocked	1.3.6.1.4.1.4325.2.10.0.14			This trap is generated when the Radio Synthesizer is not locked. It is sent out by BSU and SU.
NTF aniDevTrapRadioSynthNotLockedClear	1.3.6.1.4.1.4325.2.10.0.15			This trap is sent out by BSU and SU to indicate that aniDevTrapRadioSynthNotLocked is cleared.
NTF aniDevTrapBsuFanStatus	1.3.6.1.4.1.4325.2.10.0.16			This trap is sent out when a fan on BSU is not operational.
NTF aniDevTrapBsuFanStatusClear	1.3.6.1.4.1.4325.2.10.0.17			This trap is sent to indicate that aniDevTrapBsuFanStatus is cleared, that is, the fan on BSU is operational again.
NTF aniDevTrapBsuDc12vStatus	1.3.6.1.4.1.4325.2.10.0.18			This trap is generated when a 12V DC power failure occurs on the BSU.
NTF aniDevTrapBsuDc12vStatusClear	1.3.6.1.4.1.4325.2.10.0.19			This trap indicates that aniDevTrapBsuDc12vStatus alarm on the BSU has been cleared.
NTF aniDevTrapMssPllNotLocked	1.3.6.1.4.1.4325.2.10.0.20			The MSS PLL (Phase Locked Loop) not locked trap which is sent out by BSU.
NTF aniDevTrapMssPllNotLockedClear	1.3.6.1.4.1.4325.2.10.0.21			This trap indicates that aniDevTrapMssPllNotLocked alarm on the BSU has been cleared.
NTF aniDevTrapBsuTempTooLow	1.3.6.1.4.1.4325.2.10.0.22			This indicates that the temperature on the BSU is below the operating limits. A temperature sensor on the BSU checks the operating temperature of the system board.
NTF aniDevTrapBsuTempTooHigh	1.3.6.1.4.1.4325.2.10.0.23			This indicates that the temperature on the BSU is above the operating limits. A temperature sensor on the BSU checks the operating temperature of the system board.
NTF aniDevTrapBsuTempNormal	1.3.6.1.4.1.4325.2.10.0.24			This indicates that the temperature on the BSU is within the operating limits. It shows that either the aniDevTrapBsuTempTooLow or aniDevTrapBsuTempTooHigh alarm on the BSU has been cleared.
NTF aniDevTrapFlashSpaceTooLow	1.3.6.1.4.1.4325.2.10.0.25			This trap is sent out when the disk space on file system is too low. It can be sent out by either BSU or SU.
NTF aniDevTrapFlashSpaceNormal	1.3.6.1.4.1.4325.2.10.0.26			This trap is sent out when the disk space on file system is again normal. It can be sent out by either BSU or SU to clear the aniDevTrapFlashSpaceTooLow alarm.
NTF aniDevTrapNvramCorrupted	1.3.6.1.4.1.4325.2.10.0.27			This trap is sent out when the NVRAM is corrupted. 64 kB of NVRAM is allocated from the first block of flash on both BSU and SU. A checksum is maintained whenever some value if stored in it.
NTF aniDevTrapNvramCorruptionClear	1.3.6.1.4.1.4325.2.10.0.28			This trap indicates that aniDevTrapNvramCorrupted alarm has been cleared.
NTF aniDevTrapFileSysCorrupted	1.3.6.1.4.1.4325.2.10.0.29			This trap indicates that the file system has been corrupted. It can be sent out by either BSU or SU.
NTF aniDevTrapFileSysCorruptionClear	1.3.6.1.4.1.4325.2.10.0.30			This trap indicates that aniDevTrapFileSysCorrupted alarm has been cleared. It can be sent out by either BSU or SU.
NTF aniDevTrapSmtpConnectFailure	1.3.6.1.4.1.4325.2.10.0.31			This trap is sent out when the connection to the SMTP server fails. It can be sent out by either BSU or SU.
NTF aniDevTrapSmtpDisabled	1.3.6.1.4.1.4325.2.10.0.32			This trap is sent out when SMTP is disabled on the system (either BSU or SU).
NTF aniDevTrapSwWatchdogReset	1.3.6.1.4.1.4325.2.10.0.33			This trap is sent out when SU is reset by the Software Watchdog. The Software Watchdog feature detects low memory and task suspended cases, sends out the trap and reboots the device.
NTF aniDevTrapNatFailure	1.3.6.1.4.1.4325.2.10.0.34			This trap is sent out when NAT failure occurs. It is sent out by SU.
NTF aniDevTrapCurrentImageCorrupted	1.3.6.1.4.1.4325.2.10.0.35			This trap is sent out to indicate that the current image is corrupted. It can be sent out by both BSU or SU.
NTF aniDevTrapBsuSuFailedReg	1.3.6.1.4.1.4325.2.10.0.36			This trap is sent out when the BSU-SU registration fails.
NTF aniDevTrapDefaultConfigFileNotFound	1.3.6.1.4.1.4325.2.10.0.37			This trap is sent out when the default configuration file is not found. It can be sent out by both BSU or SU.
NTF aniDevTrapCurrentBsuState	1.3.6.1.4.1.4325.2.10.0.38			This trap shows the current BSU State.
NTF aniDevTrapCurrentSuState	1.3.6.1.4.1.4325.2.10.0.39			This trap shows the current SU State.
NTF aniDevTrapMemBufferTooLow	1.3.6.1.4.1.4325.2.10.0.40			This trap is sent out when the memory buffer is too low. It can be sent out by either BSU or SU.
NTF aniDevTrapMemBufferNormal	1.3.6.1.4.1.4325.2.10.0.41			This trap is sent out when the memory buffer is again normal. It can be sent out by either BSU or SU to clear the aniDevMemBufferTooLow alarm.
NTF aniDevTrapConfigFileVersionCheckFailure	1.3.6.1.4.1.4325.2.10.0.42			This trap is sent out when there is a problem in the version of the config file. It is sent out when either the version information is missing or if there is a mismatch in the version.
NTF aniDevTrapDefaultFileVersionCheckFailure	1.3.6.1.4.1.4325.2.10.0.43			This trap is sent out when there is a problem in the version of the default file. It is sent out when either the version information is missing or if there is a mismatch in the version.
NTF aniDevTrapConfigFileUploadFailure	1.3.6.1.4.1.4325.2.10.0.44			This trap is sent out when the upload of the config file fails.
NTF aniDevTrapConfigFileUploadChecksumFailure	1.3.6.1.4.1.4325.2.10.0.45			This trap is sent out when there is a checksum error on the config file after the upload.
NTF aniDevTrapRunningBaselineImage	1.3.6.1.4.1.4325.2.10.0.46			This trap is sent out when a baseline image is running.
NTF aniDevTrapPowerSupplyFailure	1.3.6.1.4.1.4325.2.10.0.48			This trap is sent out by the BSU when there is a power supply failure.
NTF aniDevTrapPowerSupplyNormal	1.3.6.1.4.1.4325.2.10.0.49			This trap is sent out by the BSU when the power supply is normal again. It is sent out to indicate that the aniDevTrapPowerSupplyFailure alarm is cleared.
NTF aniDevTrapRealtimeClockFailure	1.3.6.1.4.1.4325.2.10.0.50			This trap is sent out by the BSU when there is a real time clock failure.
NTF aniDevTrapRealtimeClockNormal	1.3.6.1.4.1.4325.2.10.0.51			This trap is sent out by the BSU when the real time clock is normal again. It is sent out to indicate that the aniDevTrapRealtimeClockFailure alarm is cleared.
NTF aniDevTrapModelNumFailure	1.3.6.1.4.1.4325.2.10.0.53			This trap is sent out when there is an error related to the model number.
NTF aniDevTrapConfigParseFailure	1.3.6.1.4.1.4325.2.10.0.55			This trap is sent out when there is an error in the parsing of the configuration file.
NTF aniDevUpdateInventory	1.3.6.1.4.1.4325.2.10.0.56			This trap is sent out to notify configuration change in SU customer name.
NTF aniDevTrapPppFailure	1.3.6.1.4.1.4325.2.10.0.57			This trap is sent out whenever PPP fails to establish a session.
NTF aniDevTrapPppStatus	1.3.6.1.4.1.4325.2.10.0.58			This trap is sent whenever a PPP link goes up or down.
NTF aniDevTrapFrequencyChange	1.3.6.1.4.1.4325.2.10.0.59			This trap is sent out whenever the channel frequency is changed on the BSU and SU while they are in the operational state.
NTF aniDevTrapPPPoeSessionUp	1.3.6.1.4.1.4325.2.10.0.62			This trap is sent out whenever the when a PPPoE Session comes up.
NTF aniDevTrapPPPoeOfferError	1.3.6.1.4.1.4325.2.10.0.63			This trap is sent out whenever the when no valid PPPoE Active Discovery Offer (PADO) is received in response to a PPPoE Active Discovery Initiation (PADI) packet or if no valid PPPoE Active Discovery Session-confirmation (PADS) is received in response to a PPPoE Active Discovery Request (PADR) packet.
NTF aniDevTrapPPPoeSessionTerminate	1.3.6.1.4.1.4325.2.10.0.64			This trap is sent out when a PPPoE Session is terminated.
NTF aniDevTrapEtherAutoNegotiate	1.3.6.1.4.1.4325.2.10.0.65			This trap is sent out when device go back to auto-negotiate mode.
NTF aniDevTrapRadioInitError	1.3.6.1.4.1.4325.2.10.0.66			This trap is sent out when the radio can't be initialized. Under an error condition this event will be generated prior to SU becoming operational.
NTF aniDevTrapMaxPowerError	1.3.6.1.4.1.4325.2.10.0.67			This trap is sent out when when the radio board can't reach maximum configured power. This can be caused by a combination of faulty (or very long) coaxial cable connecting IDU and ODU and/or extremely hot weather or just bad calibration data on the radio board.
NTF aniDevTrapMaxPowerErrorClear	1.3.6.1.4.1.4325.2.10.0.68			This trap is sent out when the event aniDevTrapMaxPowerError has been cleared.
NTF aniDevTrapAgcTableNotCalibrated	1.3.6.1.4.1.4325.2.10.0.69			This trap is sent out when the AGC Table is not calibrated. SODU platform relies on accurate calibration of the receive gain throughout the entire receive chain. If the table is not correctly calibrated or gets corrupted in the field, the SODU will have to fall back on default receive power adjustment algorithm, which may be far from optimal. This problem doesn't stop an SODU from getting operational but the downstream link quality can suffer.
NTF aniDevTrapFreqTableInvalidEntry	1.3.6.1.4.1.4325.2.10.0.70			This trap is sent out whenever the frequency table contains an invalid entry.
NTF aniDevTrapHtmlUnzippedError	1.3.6.1.4.1.4325.2.10.0.71			This trap is sent out when html compressed zip files are either missing or corrupted.
NTF aniDevTrapBootLineBackupUpdated	1.3.6.1.4.1.4325.2.10.0.72			This trap is sent out whenever the backup bootline parameters are updated to bring them in sync with the actual boot parameters.
NTF aniDevTrapBootLineRestoredFromBackup	1.3.6.1.4.1.4325.2.10.0.73			This trap is sent out when the main bootline parameters are corrupted and the system has to fall back on backup boot parameters.
NTF aniDevTrapNvramBackupUpdated	1.3.6.1.4.1.4325.2.10.0.74			This trap is sent out whenever the backup copy of NVRAM configuration parameters is updated to bring them in sync with the actual NVRAM configuration.
NTF aniDevTrapNvramRestoredFromBackup	1.3.6.1.4.1.4325.2.10.0.75			This trap is sent out when the main NVRAM configuration data is corrupted and the system has to fall back on backup NVRAM configuration.
aniDevTrapControl	1.3.6.1.4.1.4325.2.10.1
INT aniDevControlTrapGeneration	1.3.6.1.4.1.4325.2.10.1.1	INTEGER	read-write	Enable or disable SNMP Trap Generation.

RFC description

Generates device-level SNMP traps for BSU/SU subscriber units including sync acquisition, operational status, and DHCP failure notifications.

Start monitoring Aperto Networks BSU/SU fixed wireless unit (trap notifications) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DEVTRAPS-MIB

What Is DEVTRAPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description