DES3528-L2MGMT-MIB

All MIBs › DES3528-L2MGMT-MIB

Organization: D-Link Corp.

Last Updated: 2008-12-01

Category: VLAN and Bridging, Vendor: D-Link

Description: Manages L2 features including VLANs, spanning tree, and port settings for D-Link DES-3528.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3528-L2MGMT-MIB?

DES3528-L2MGMT-MIB is a D-Link proprietary MIB defining Layer 2 network management information for the DES-3528 managed switch. Its objects cover front-panel LED status, total/in-use port counts, spanning-tree state, IGMP snooping (with a multicast-router-port-only variant), SNMP trap state, statistics-counter reset, FDB-table VLAN scoping, MAC-notification state/history-size/interval, asymmetric-VLAN state, Telnet/Web state and TCP port, management VLAN ID, LLDP state and forwarding, IP auto-configuration, and CFM (Connectivity Fault Management) state and per-port configuration. As a configuration/status MIB it lets an administrator confirm core Layer 2 management settings — spanning tree, IGMP snooping, management VLAN — are configured as intended on the switch. It is deployed on the D-Link DES-3528 managed switch. Engineers can download the DES3528-L2MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3528-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3528 managed switch

Monitoring Examples

An administrator checks swL2DevCtrlStpState and swL2DevCtrlIGMPSnooping to confirm spanning-tree and multicast-snooping are both enabled as expected on a D-Link DES-3528 switch.

What Can Be Monitored

spanning-tree, IGMP snooping, and management VLAN configuration

Imported Objects

From DLINK-ID-REC-MIB

AgentNotifyLevel

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

From SW3528PRIMGMT-MIB

des3528

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.105.1.2			The Structure of Layer 2 Network Management Information.
swL2DevMgmt	1.3.6.1.4.1.171.11.105.1.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.105.1.2.1.1
INT swDevInfoTotalNumOfPort	1.3.6.1.4.1.171.11.105.1.2.1.1.1	INTEGER	read-only	The number of ports within this switch. This value is the sum of the ports within this switch.
INT swDevInfoNumOfPortInUse	1.3.6.1.4.1.171.11.105.1.2.1.1.2	INTEGER	read-only	The number of ports in this switch connected to the segment or the end stations.
OCT swDevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.11.105.1.2.1.1.4	OCTET STRING	read-only	This object is a set of system LED indications. The first five octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.11.105.1.2.1.2
INT swL2DevCtrlStpState	1.3.6.1.4.1.171.11.105.1.2.1.2.1	INTEGER	read-write	This object can enable or disable the spanning tree algorithm during the runtime of the system.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.105.1.2.1.2.2	INTEGER	read-write	This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
INT swL2DevCtrlIGMPSnoopingMcstRTOnly	1.3.6.1.4.1.171.11.105.1.2.1.2.3	INTEGER	read-write	This object controls IGMP snooping forward multicast routing only state.
INT swL2DevCtrlSnmpTrapState	1.3.6.1.4.1.171.11.105.1.2.1.2.5	INTEGER	read-write	This object controls the SNMP trap status.
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.105.1.2.1.2.6	INTEGER	read-write	When the object is set to active, all statistical counters will be cleared. If set to normal, no action.
VLA swL2DevCtrlVlanIdOfFDBTbl	1.3.6.1.4.1.171.11.105.1.2.1.2.7	VlanId	read-write	Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.105.1.2.1.2.8	INTEGER	read-write	This object can enable or disable MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.105.1.2.1.2.9	INTEGER	read-write	This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.105.1.2.1.2.10	INTEGER	read-write	This object indicates the time interval, in seconds, which will trigger MAC notification messages.
INT swL2DevCtrlAsymVlanState	1.3.6.1.4.1.171.11.105.1.2.1.2.13	INTEGER	read-write	This object enables or disables asymmetric VLANs during the runtime of the system.
swL2DevCtrlTelnet	1.3.6.1.4.1.171.11.105.1.2.1.2.14
INT swL2DevCtrlTelnetState	1.3.6.1.4.1.171.11.105.1.2.1.2.14.1	INTEGER	read-write	This object controls the Telnet status.
INT swL2DevCtrlTelnetTcpPort	1.3.6.1.4.1.171.11.105.1.2.1.2.14.2	INTEGER	read-write	This object designates TCP ports. When Telnet is disabled, this object is not accessible.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.105.1.2.1.2.16	VlanId	read-write	This object controls which previously created VLANs are included in the System IP Interface.
swL2DevCtrlWeb	1.3.6.1.4.1.171.11.105.1.2.1.2.17
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.11.105.1.2.1.2.17.1	INTEGER	read-write	This object controls the Web status.
INT swL2DevCtrlWebTcpPort	1.3.6.1.4.1.171.11.105.1.2.1.2.17.2	INTEGER	read-write	This object designates TCP ports. When Web is disabled, this object is not accessible.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.105.1.2.1.2.18	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.105.1.2.1.2.19	INTEGER	read-write	When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded.
INT swL2DevCtrlIpAutoconfig	1.3.6.1.4.1.171.11.105.1.2.1.2.20	INTEGER	read-write	This object controls the IP auto configuration state.
swL2DevCtrlCFM	1.3.6.1.4.1.171.11.105.1.2.1.2.21
INT swL2DevCtrlCFMState	1.3.6.1.4.1.171.11.105.1.2.1.2.21.1	INTEGER	read-write	This object indicates the CFM global state.
swL2DevCtrlCFMPortTable	1.3.6.1.4.1.171.11.105.1.2.1.2.21.2		not-accessible	A table containing CFM state of speicified ports.
swL2DevCtrlCFMPortEntry	1.3.6.1.4.1.171.11.105.1.2.1.2.21.2.1		not-accessible	The entry of CFM state on speicified ports.
INT swL2DevCtrlCFMPortIndex	1.3.6.1.4.1.171.11.105.1.2.1.2.21.2.1.1	INTEGER	not-accessible	This object indicates the port-num.
INT swL2DevCtrlCFMPortState	1.3.6.1.4.1.171.11.105.1.2.1.2.21.2.1.2	INTEGER	read-write	This object indicates the CFM state on per-port.
INT swL2DevCtrlVLANTrunkState	1.3.6.1.4.1.171.11.105.1.2.1.2.22	INTEGER	read-write	This indicates the global state of the VLAN trunking feature of the device.
swL2DevAlarm	1.3.6.1.4.1.171.11.105.1.2.1.3
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.171.11.105.1.2.1.3.1	INTEGER	read-write	When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.
INT swL2DevAlarmTopologyChange	1.3.6.1.4.1.171.11.105.1.2.1.3.2	INTEGER	read-write	This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.105.1.2.1.3.3	INTEGER	read-write	This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other.
swL2VLANMgmt	1.3.6.1.4.1.171.11.105.1.2.2
swL2VlanStaticTable	1.3.6.1.4.1.171.11.105.1.2.2.1		not-accessible	A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
swL2VlanStaticEntry	1.3.6.1.4.1.171.11.105.1.2.2.1.1		not-accessible	Static information for a VLAN configured into the device by (local or network) management.
VLA swL2VlanIndex	1.3.6.1.4.1.171.11.105.1.2.2.1.1.1	VlanId	not-accessible	The VLAN-ID or other identifier referring to this VLAN.
INT swL2VLANAdvertisement	1.3.6.1.4.1.171.11.105.1.2.2.1.1.2	INTEGER	read-write	This object indicates if the advertisement is active or not.
INT swL2PVIDAutoAssignmentState	1.3.6.1.4.1.171.11.105.1.2.2.2	INTEGER	read-write	This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'.
swL2VlanPortInfoTable	1.3.6.1.4.1.171.11.105.1.2.2.3		not-accessible	A table containing vlan and port role information of each port.
swL2VlanPortInfoEntry	1.3.6.1.4.1.171.11.105.1.2.2.3.1		not-accessible	The table entry of vlan port information.
INT swL2VlanPortInfoPortIndex	1.3.6.1.4.1.171.11.105.1.2.2.3.1.1	INTEGER	read-only	The port index.
INT swL2VlanPortInfoVid	1.3.6.1.4.1.171.11.105.1.2.2.3.1.2	INTEGER	read-only	The VLAN-ID assigned to a special port
INT swL2VlanPortInfoPortRole	1.3.6.1.4.1.171.11.105.1.2.2.3.1.3	INTEGER	read-only	The port role of a special port.when none,it means this port is not belong to the vlan.
INT swL2NniGvrpBpduAddress	1.3.6.1.4.1.171.11.105.1.2.2.6	INTEGER	read-write	Specifies the GVRP's BPDU MAC address of NNI port In Q-in_Q status.
swL2PortMgmt	1.3.6.1.4.1.171.11.105.1.2.3
swL2PortInfoTable	1.3.6.1.4.1.171.11.105.1.2.3.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.105.1.2.3.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.105.1.2.3.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoMediumType	1.3.6.1.4.1.171.11.105.1.2.3.1.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortInfoUnitID	1.3.6.1.4.1.171.11.105.1.2.3.1.1.3	INTEGER	read-only	Indicates ID of the unit in the system
INT swL2PortInfoType	1.3.6.1.4.1.171.11.105.1.2.3.1.1.4	INTEGER	read-only	This object indicates the connector type of this port.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.105.1.2.3.1.1.5	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.105.1.2.3.1.1.6	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInfoErrorDisabled	1.3.6.1.4.1.171.11.105.1.2.3.1.1.8	INTEGER	read-only	This object indicates the blocking type of this port.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.105.1.2.3.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.105.1.2.3.2.1		not-accessible	A list of control information for each port on the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.105.1.2.3.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlMediumType	1.3.6.1.4.1.171.11.105.1.2.3.2.1.2	INTEGER	read-only	Indicates the medium type of the port number.
INT swL2PortCtrlUnitIndex	1.3.6.1.4.1.171.11.105.1.2.3.2.1.3	INTEGER	read-only	Indicates the ID of the unit in the device
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.4	INTEGER	read-write	This object decides if the port is enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.5	INTEGER	read-write	Chose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.6	INTEGER	read-write	The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
INT swL2PortCtrlLearningState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.7	INTEGER	read-write	This object decides if the port is locked or not.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.8	INTEGER	read-write	This object sets each port's MAC notification state.
INT swL2PortCtrlMDIXState	1.3.6.1.4.1.171.11.105.1.2.3.2.1.10	INTEGER	read-write	This object configures the MDIX setting of the port.
INT swL2PortCtrlJumboFrame	1.3.6.1.4.1.171.11.105.1.2.3.3	INTEGER	read-write	This object configures the switch's jumbo frame settings.
INT swL2PortCtrlJumboFrameMaxSize	1.3.6.1.4.1.171.11.105.1.2.3.4	INTEGER	read-only	This object describes how many bytes the max jumbo frame is.
swL2PortCableDiagnosisTable	1.3.6.1.4.1.171.11.105.1.2.3.5		not-accessible	A table that contains cable diagnostic information about every port.
swL2PortCableDiagnosisEntry	1.3.6.1.4.1.171.11.105.1.2.3.5.1		not-accessible	A list of cable diagnostic information for each port of the device.
INT swL2PortCableDiagnosisPortIndex	1.3.6.1.4.1.171.11.105.1.2.3.5.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCableDiagnosisPairIndex	1.3.6.1.4.1.171.11.105.1.2.3.5.1.2	INTEGER	read-only	Indicates pair index of the port. The pair 1 means the pin 3 and 6 of the connector. The pair 2 means the pin 1 and 2 of the connector. The pair 3 means the pin 7 and 8 of the connector. The pair 4 means the pin 4 and 5 of the connector.
INT swL2PortCableDiagnosisCableStatus	1.3.6.1.4.1.171.11.105.1.2.3.5.1.3	INTEGER	read-only	This object indicates the cable status.
INT swL2PortCableDiagnosisPairStatus	1.3.6.1.4.1.171.11.105.1.2.3.5.1.4	INTEGER	read-only	This object indicates the status of the pair.
INT swL2PortCableDiagnosisPairLength	1.3.6.1.4.1.171.11.105.1.2.3.5.1.5	INTEGER	read-only	This object indicates the approx. length or length to failure of the pair. The unit value is in meters.
INT swL2PortCableDiagnosisPairLengthInaccuracy	1.3.6.1.4.1.171.11.105.1.2.3.5.1.6	INTEGER	read-only	This object indicates the inaccuracy of a pair length. The unit value is in meters.
swL2PortCounterCtrlTable	1.3.6.1.4.1.171.11.105.1.2.3.6		not-accessible	A table that used to clear counter information about every port.
swL2PortCounterCtrlEntry	1.3.6.1.4.1.171.11.105.1.2.3.6.1		not-accessible	A list of entry used to clear counter information for each port of the device.
INT swL2PortCounterCtrlPortIndex	1.3.6.1.4.1.171.11.105.1.2.3.6.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCounterClearCtrl	1.3.6.1.4.1.171.11.105.1.2.3.6.1.2	INTEGER	read-write	This object indicates if to clear the counters for each port of the device or not.
swL2PortErrTable	1.3.6.1.4.1.171.11.105.1.2.3.7		not-accessible	A table that contains error information for each port.
swL2PortErrEntry	1.3.6.1.4.1.171.11.105.1.2.3.7.1		not-accessible	A list of information regarding port errors on the device.
INT swL2PortErrPortIndex	1.3.6.1.4.1.171.11.105.1.2.3.7.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module).
INT swL2PortErrPortState	1.3.6.1.4.1.171.11.105.1.2.3.7.1.2	INTEGER	read-only	This object indicates the port state is enabled or disabled.
INT swL2PortErrPortConnStatus	1.3.6.1.4.1.171.11.105.1.2.3.7.1.3	INTEGER	read-only	This object indicates whether the PortStatus is err-disabled or not.
INT swL2PortErrPortReason	1.3.6.1.4.1.171.11.105.1.2.3.7.1.4	INTEGER	read-only	This object describes if the reason for the port error is STP LBD or Storm control.
swL2LimitedMulticastMgmt	1.3.6.1.4.1.171.11.105.1.2.5
swL2MulticastFilterProfileTable	1.3.6.1.4.1.171.11.105.1.2.5.1		not-accessible	A table that contains information about multicast filter address.
swL2MulticastFilterProfileEntry	1.3.6.1.4.1.171.11.105.1.2.5.1.1		not-accessible	A list of multicast filter address information for each profile ID.
INT swL2MulticastFilterProfileIndex	1.3.6.1.4.1.171.11.105.1.2.5.1.1.1	INTEGER	read-only	Indicates index for each profile.
STR swL2MulticastFilterProfileName	1.3.6.1.4.1.171.11.105.1.2.5.1.1.2	DisplayString	read-create	Specifies a profile name for each multicast filter profile.
ROW swL2MulticastFilterStatus	1.3.6.1.4.1.171.11.105.1.2.5.1.1.3	RowStatus	read-create	This object indicates the status of this entry.
swL2MulticastFilterProfileAddressTable	1.3.6.1.4.1.171.11.105.1.2.5.2		not-accessible	A table that contains information about multicast filter address.
swL2MulticastFilterProfileAddressEntry	1.3.6.1.4.1.171.11.105.1.2.5.2.1		not-accessible	A list of multicast filter address information for each profile ID.
INT swL2MulticastFilterProfileIdIndex	1.3.6.1.4.1.171.11.105.1.2.5.2.1.1	INTEGER	read-only	Indicates index for each profile.
IP swL2MulticastFilterFromIp	1.3.6.1.4.1.171.11.105.1.2.5.2.1.2	IpAddress	read-only	Specifies the head IP address of a multicast address range which will be binded to a multicast filter profile.
IP swL2MulticastFilterToIp	1.3.6.1.4.1.171.11.105.1.2.5.2.1.3	IpAddress	read-only	Specifies the tail IP address of a multicast address range which will be binded to a multicast filter profile.
ROW swL2MulticastFilterAddressState	1.3.6.1.4.1.171.11.105.1.2.5.2.1.4	RowStatus	read-create	This object indicates the status of this entry. Setting value to createAndGo(4) will add the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp to multicast filter profile. Setting value to destroy(6) will remove the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp from multicast filter profile.
swL2LimitedMulticastFilterPortTable	1.3.6.1.4.1.171.11.105.1.2.5.3		not-accessible	A table that used to bind port to profile id.
swL2LimitedMulticastFilterPortEntry	1.3.6.1.4.1.171.11.105.1.2.5.3.1		not-accessible	A list of information that used to bind port to profile id.
INT swL2LimitedMulticastFilterPortIndex	1.3.6.1.4.1.171.11.105.1.2.5.3.1.1	INTEGER	read-only	Specifies port as an index.
INT swL2LimitedMulticastFilterPortAccess	1.3.6.1.4.1.171.11.105.1.2.5.3.1.2	INTEGER	read-write	This object indicates the access status for each port.
STR swL2LimitedMulticastFilterPortProfileID	1.3.6.1.4.1.171.11.105.1.2.5.3.1.3	DisplayString	read-write	This object specifies a profile ID list for each port.
INT swL2LimitedMulticastFilterPortProfileStatus	1.3.6.1.4.1.171.11.105.1.2.5.3.1.4	INTEGER	read-create	Controls the multicast filter profile list which bind to each port. When set add(2), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be bound to the port. When set delete(3), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be unbound from the port. The attribute value reverts to 'other' once the action has been done.
swL2MulticastFilterPortMaxGroupTable	1.3.6.1.4.1.171.11.105.1.2.5.4		not-accessible	A table that contains information about max group number based on port.
swL2MulticastFilterPortMaxGroupEntry	1.3.6.1.4.1.171.11.105.1.2.5.4.1		not-accessible	A list of max group number information for each port.
INT swL2MulticastFilterPortMaxGroupPortIndex	1.3.6.1.4.1.171.11.105.1.2.5.4.1.1	INTEGER	read-only	Specifies port number as table index.
INT swL2MulticastFilterPortMaxGroup	1.3.6.1.4.1.171.11.105.1.2.5.4.1.2	INTEGER	read-write	Specifies maximum multicast filter group numbers for each port. Default value is 0,and 0 means infinite.
swL2QOSMgmt	1.3.6.1.4.1.171.11.105.1.2.6
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.11.105.1.2.6.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.11.105.1.2.6.1.1		not-accessible	A list of information contained in the swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.11.105.1.2.6.1.1.1	INTEGER	read-only	Indicates the port .
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.11.105.1.2.6.1.1.2	INTEGER	read-write	Indicates RX Rate of the specified port. Value 1024001 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.11.105.1.2.6.1.1.3	INTEGER	read-write	Indicates TX Rate of the specified port. Value 1024001 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.11.105.1.2.6.1.1.4	INTEGER	read-only	The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.11.105.1.2.6.1.1.5	INTEGER	read-only	The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.11.105.1.2.6.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.11.105.1.2.6.2.1		not-accessible	A list of information contained in the swL2QOSSchedulingTable.
INT swL2QOSSchedulingClassIndex	1.3.6.1.4.1.171.11.105.1.2.6.2.1.1	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxPkts	1.3.6.1.4.1.171.11.105.1.2.6.2.1.2	INTEGER	read-write	Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.
INT swL2QOSSchedulingMechanism	1.3.6.1.4.1.171.11.105.1.2.6.2.1.3	INTEGER	read-only	Indicates the mechanism of QoS scheduling.
INT swL2QOSSchedulingMaxLatency	1.3.6.1.4.1.171.11.105.1.2.6.2.1.4	INTEGER	read-write	Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmitting its packets. A value between 0 and 255 can be specified- with this value multiplied by 16 ms to arrive at the total allowed time for queue to transmit packets. For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.11.105.1.2.6.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.11.105.1.2.6.3.1		not-accessible	A list of information contained in the swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.11.105.1.2.6.3.1.1	INTEGER	read-only	The 802.1p user priority .
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.11.105.1.2.6.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has seven hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.11.105.1.2.6.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.11.105.1.2.6.4.1		not-accessible	A list of information contained in the swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.11.105.1.2.6.4.1.1	INTEGER	read-only	Indicates the port number .
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.11.105.1.2.6.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch..
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.11.105.1.2.6.4.1.3	INTEGER	read-only	The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
INT swL2QOSSchedulingMechanismCtrl	1.3.6.1.4.1.171.11.105.1.2.6.5	INTEGER	read-write	This object controls QoS scheduling Mechanism.
INT swL2QOSHolPreventionCtrl	1.3.6.1.4.1.171.11.105.1.2.6.6	INTEGER	read-write	Controls QoS HoL Prevention
swL2PortSecurityMgmt	1.3.6.1.4.1.171.11.105.1.2.7
swL2PortSecurityControlTable	1.3.6.1.4.1.171.11.105.1.2.7.1		not-accessible	A port security feature which controls the address leaning capability and traffic forwarding decisions. Each port can be enabled or disabled for this function. When it is enabled and a number is given said N, which allows N addresses to be learned on this port, the first N learned addresses are locked at this port as static entries. When the learned addresses number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned on this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.11.105.1.2.7.1.1		not-accessible	A list of information contained in the swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.11.105.1.2.7.1.1.1	INTEGER	read-only	Indicates the secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.11.105.1.2.7.1.1.2	INTEGER	read-write	Indicates allowable number of addresses to be learned on this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.11.105.1.2.7.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset(4) mode - Locked addresses never age out unless the system restarts which will prevent port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.11.105.1.2.7.1.1.4	INTEGER	read-write	Indicates administration state of locking address.
INT swL2PortSecurityEntryClearCtrl	1.3.6.1.4.1.171.11.105.1.2.7.1.1.5	INTEGER	read-write	Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.
swL2PortSecurityDelCtrl	1.3.6.1.4.1.171.11.105.1.2.7.2
STR swL2PortSecurityDelVlanName	1.3.6.1.4.1.171.11.105.1.2.7.2.1	DisplayString	read-write	Indicates VLAN name.
INT swL2PortSecurityDelPort	1.3.6.1.4.1.171.11.105.1.2.7.2.2	INTEGER	read-write	Indicates the port.
MAC swL2PortSecurityDelMacAddress	1.3.6.1.4.1.171.11.105.1.2.7.2.3	MacAddress	read-write	Specifies a MAC address.
INT swL2PortSecurityDelActivity	1.3.6.1.4.1.171.11.105.1.2.7.2.4	INTEGER	read-write	.
INT swL2PortSecurityTrapLogState	1.3.6.1.4.1.171.11.105.1.2.7.3	INTEGER	read-write	When enabled(2),whenever there's a new MAC address that violates the pre-defined port security configuration, traps will be sent out and the relevant information will be logged into the system.
swL2DhcpRelayMgmt	1.3.6.1.4.1.171.11.105.1.2.8
INT swL2DhcpRelayState	1.3.6.1.4.1.171.11.105.1.2.8.1	INTEGER	read-write	This object indicates if the DHCP relay function is enabled or disabled.
INT swL2DhcpRelayHopCount	1.3.6.1.4.1.171.11.105.1.2.8.2	INTEGER	read-write	This object indicates the maximum number of router hops that DHCP packets can cross.
INT swL2DhcpRelayTimeThreshold	1.3.6.1.4.1.171.11.105.1.2.8.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
INT swL2DhcpRelayOption82State	1.3.6.1.4.1.171.11.105.1.2.8.4	INTEGER	read-write	This object indicates if the DHCP relay agent information option 82 function is enabled or disabled.
INT swL2DhcpRelayOption82Check	1.3.6.1.4.1.171.11.105.1.2.8.5	INTEGER	read-write	This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
INT swL2DhcpRelayOption82Policy	1.3.6.1.4.1.171.11.105.1.2.8.6	INTEGER	read-write	This object indicates the reforwarding policy of DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option 82 field messages.
swL2DhcpRelayCtrlTable	1.3.6.1.4.1.171.11.105.1.2.8.7		not-accessible	This table specifies the IP address as a destination to forward (relay) DHCP packets to.
swL2DhcpRelayCtrlEntry	1.3.6.1.4.1.171.11.105.1.2.8.7.1		not-accessible	A list of information that specifies the IP address as a destination to forward (relay) DHCP packets to.
STR swL2DhcpRelayCtrlInterfaceName	1.3.6.1.4.1.171.11.105.1.2.8.7.1.1	DisplayString	read-only	The name of the IP interface.
IP swL2DhcpRelayCtrlServer	1.3.6.1.4.1.171.11.105.1.2.8.7.1.2	IpAddress	read-only	The DHCP server IP address.
INT swL2DhcpRelayCtrlState	1.3.6.1.4.1.171.11.105.1.2.8.7.1.3	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table.
swL2TrunkMgmt	1.3.6.1.4.1.171.11.105.1.2.9
INT swL2TrunkMaxSupportedEntries	1.3.6.1.4.1.171.11.105.1.2.9.1	INTEGER	read-only	Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
INT swL2TrunkCurrentNumEntries	1.3.6.1.4.1.171.11.105.1.2.9.2	INTEGER	read-only	Current active number of entries in the trunk configuration table.
swL2TrunkCtrlTable	1.3.6.1.4.1.171.11.105.1.2.9.3		not-accessible	This table specifies which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkCtrlEntry	1.3.6.1.4.1.171.11.105.1.2.9.3.1		not-accessible	A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkIndex	1.3.6.1.4.1.171.11.105.1.2.9.3.1.1	INTEGER	read-only	The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
INT swL2TrunkMasterPort	1.3.6.1.4.1.171.11.105.1.2.9.3.1.3	INTEGER	read-create	The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swL2TrunkMember	1.3.6.1.4.1.171.11.105.1.2.9.3.1.4	PortList	read-create	Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
INT swL2TrunkFloodingPort	1.3.6.1.4.1.171.11.105.1.2.9.3.1.5	INTEGER	read-only	The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
INT swL2TrunkType	1.3.6.1.4.1.171.11.105.1.2.9.3.1.6	INTEGER	read-create	This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .
ROW swL2TrunkState	1.3.6.1.4.1.171.11.105.1.2.9.3.1.7	RowStatus	read-create	This object indicates the status of this entry.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.105.1.2.9.4	INTEGER	read-write	This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.11.105.1.2.9.5		not-accessible	This table specifies which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.11.105.1.2.9.5.1		not-accessible	A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.11.105.1.2.9.5.1.1	INTEGER	read-only	The index of logical port LACP.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.11.105.1.2.9.5.1.2	INTEGER	read-write	The state of logical port LACP.
swL2TrunkVLANTable	1.3.6.1.4.1.171.11.105.1.2.9.6		not-accessible	This table is used to manage the VLAN trunking feature of the device.
swL2TrunkVLANEntry	1.3.6.1.4.1.171.11.105.1.2.9.6.1		not-accessible	This object is used to configure the VLAN trunking settings for each port.
INT swL2TrunkVLANPort	1.3.6.1.4.1.171.11.105.1.2.9.6.1.1	INTEGER	read-only	This object indicates the port being configured.
INT swL2TrunkVLANState	1.3.6.1.4.1.171.11.105.1.2.9.6.1.2	INTEGER	read-write	The state of the logical port.
swL2MirrorMgmt	1.3.6.1.4.1.171.11.105.1.2.10
INT swL2MirrorLogicTargetPort	1.3.6.1.4.1.171.11.105.1.2.10.1	INTEGER	read-write	This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
POR swL2MirrorPortSourceIngress	1.3.6.1.4.1.171.11.105.1.2.10.2	PortList	read-write	This represents the port where ingress packets will be sniffed.
POR swL2MirrorPortSourceEgress	1.3.6.1.4.1.171.11.105.1.2.10.3	PortList	read-write	This represents the port where egress packets will be sniffed.
INT swL2MirrorPortState	1.3.6.1.4.1.171.11.105.1.2.10.4	INTEGER	read-write	This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table.
swL2IGMPMgmt	1.3.6.1.4.1.171.11.105.1.2.11
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.11.105.1.2.11.1	INTEGER	read-only	Maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPMaxIpGroupNumPerVlan	1.3.6.1.4.1.171.11.105.1.2.11.2	INTEGER	read-only	Maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table(swL2IGMPQueryInfoTable).
INT swL2IGMPSnoopingMulticastVlanState	1.3.6.1.4.1.171.11.105.1.2.11.3	INTEGER	read-write	It indicates the global state of igmp_snoop multicast_vlan.
swL2IGMPCtrlTable	1.3.6.1.4.1.171.11.105.1.2.11.4		not-accessible	The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN is disabled, there is only one entry in the table, with an index of 1. If the VLAN is in Port-Base or 802.1q mode, the maximum number of entries can be 12, with an index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.11.105.1.2.11.4.1		not-accessible	The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.11.105.1.2.11.4.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN ID. If the VLAN is disabled, the VID is always 0 and cannot be changed by management users. If the VLAN is in Port-Base mode, the VID is arranged from 1 to 12, in a fixed form. If the VLAN is in 802.1q mode, the VID setting can be changed from 1 to 4094 by the management user, and the VID in each entry must be unique within the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.11.105.1.2.11.4.1.2	INTEGER	read-write	The frequency at which IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.11.105.1.2.11.4.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.11.105.1.2.11.4.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.11.105.1.2.11.4.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPHostTimeout	1.3.6.1.4.1.171.11.105.1.2.11.4.1.6	INTEGER	read-write	The timer value for sending IGMP query packets when none were sent by the host on the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query messages if the timer expires. Please reference RFC2236-1997.
INT swL2IGMPRouteTimeout	1.3.6.1.4.1.171.11.105.1.2.11.4.1.7	INTEGER	read-write	The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
INT swL2IGMPLeaveTimer	1.3.6.1.4.1.171.11.105.1.2.11.4.1.8	INTEGER	read-write	When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.11.105.1.2.11.4.1.9	INTEGER	read-write	This object decides if the IGMP query is enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.11.105.1.2.11.4.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.11.105.1.2.11.4.1.11	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP function is disabled for this entry. enable(3) - IGMP function is enabled for this entry.
INT swL2IGMPFastLeaveState	1.3.6.1.4.1.171.11.105.1.2.11.4.1.12	INTEGER	read-write	This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP fast-leave function is disabled for this entry. enable(3) - IGMP fast-leave function is enabled for this entry.
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.11.105.1.2.11.5		not-accessible	The table contains the number current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.11.105.1.2.11.5.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of the associated VLAN entry are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.11.105.1.2.11.5.1.1	INTEGER	read-only	This object indicates the VID of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.11.105.1.2.11.5.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function was enabled, on a per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.11.105.1.2.11.5.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
swL2IGMPInfoTable	1.3.6.1.4.1.171.11.105.1.2.11.6		not-accessible	The table containing current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of the associated VLAN entries are all enabled. Note that the priority of IGMP table entries is lower than the Filtering Table, i.e. if there is a table hash collision between entries in the IGMP Table and Filtering Table inside the switch's H/W address table, then Filtering Table entry overwrites the colliding entry of the IGMP Table. Also see the swL2FilterMgmt description.
swL2IGMPInfoEntry	1.3.6.1.4.1.171.11.105.1.2.11.6.1		not-accessible	Information about current IGMP information which was captured by this device, provided that the swL2DevCtrlIGMPSnooping and the swL2IGMPCtrlState of associated VLAN entries are all enabled.
INT swL2IGMPVid	1.3.6.1.4.1.171.11.105.1.2.11.6.1.1	INTEGER	read-only	This object indicates the VID of individual IGMP table entries. It shows the VID IGMP report information captured on the network.
IP swL2IGMPGroupIpAddr	1.3.6.1.4.1.171.11.105.1.2.11.6.1.2	IpAddress	read-only	This object identifies group IP addresses which were captured from IGMP packets, on a per-VLAN basis.
MAC swL2IGMPMacAddr	1.3.6.1.4.1.171.11.105.1.2.11.6.1.3	MacAddress	read-only	This object identifies MAC addresses which correspond to the swL2IGMPGroupIpAddr, on per-VLAN basis.
POR swL2IGMPPortMap	1.3.6.1.4.1.171.11.105.1.2.11.6.1.4	PortList	read-only	This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string which is indicated by a port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bits corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logical port. If the unit is less than 32 ports, other ports are not affected and are replaced with zeroes.
INT swL2IGMPIpGroupReportCount	1.3.6.1.4.1.171.11.105.1.2.11.6.1.5	INTEGER	read-only	This object indicates how many report packets were receive by our device, that correspond with this entry when the IGMP function is enabled on per-VLAN basis.
swL2IGMPRouterPortTable	1.3.6.1.4.1.171.11.105.1.2.11.7		not-accessible	The information of the router port table.
swL2IGMPRouterPortEntry	1.3.6.1.4.1.171.11.105.1.2.11.7.1		not-accessible	The entry of swL2IGMPRouterPortTable.
INT swL2IGMPRouterPortVlanid	1.3.6.1.4.1.171.11.105.1.2.11.7.1.1	INTEGER	read-only	This object indicates the VLAN ID of the router port entry.
STR swL2IGMPRouterPortVlanName	1.3.6.1.4.1.171.11.105.1.2.11.7.1.2	DisplayString	read-only	This object indicates the VLAN name of the router port entry.
POR swL2IGMPRouterPortStaticPortList	1.3.6.1.4.1.171.11.105.1.2.11.7.1.3	PortList	read-write	This object indicates the static portlist of the router port entry.
POR swL2IGMPRouterPortDynamicPortList	1.3.6.1.4.1.171.11.105.1.2.11.7.1.4	PortList	read-only	This object indicates the dynamic portlist of the router port entry.
POR swL2IGMPRouterPortForbiddenPortList	1.3.6.1.4.1.171.11.105.1.2.11.7.1.5	PortList	read-write	This object indicates the forbidden portlist of the router port entry.
swL2IGMPMulticastVlanTable	1.3.6.1.4.1.171.11.105.1.2.11.8		not-accessible	The information of the IGMP snooping multicast VLAN table.
swL2IGMPMulticastVlanEntry	1.3.6.1.4.1.171.11.105.1.2.11.8.1		not-accessible	The entry of swL2IGMPMulticastVlanTable.
INT swL2IGMPMulticastVlanid	1.3.6.1.4.1.171.11.105.1.2.11.8.1.1	INTEGER	read-only	This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
STR swL2IGMPMulticastVlanName	1.3.6.1.4.1.171.11.105.1.2.11.8.1.2	DisplayString	read-create	This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
POR swL2IGMPMulticastVlanSourcePort	1.3.6.1.4.1.171.11.105.1.2.11.8.1.3	PortList	read-write	This object indicate the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
POR swL2IGMPMulticastVlanMemberPort	1.3.6.1.4.1.171.11.105.1.2.11.8.1.4	PortList	read-write	This object indicate the portlist of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
POR swL2IGMPMulticastVlanTagMemberPort	1.3.6.1.4.1.171.11.105.1.2.11.8.1.5	PortList	read-write	This object indicate the portlist of the tag member ports of IGMP snooping multicast VLAN.
INT swL2IGMPMulticastVlanState	1.3.6.1.4.1.171.11.105.1.2.11.8.1.6	INTEGER	read-write	This object can be enabled or disabled IGMP_snooping multicast VLAN.
IP swL2IGMPMulticastVlanReplaceSourceIp	1.3.6.1.4.1.171.11.105.1.2.11.8.1.7	IpAddress	read-write	The replace source IP of this multicast vlan.
ROW swL2IGMPMulticastVlanRowStatus	1.3.6.1.4.1.171.11.105.1.2.11.8.1.8	RowStatus	read-create	This object indicates the status of this entry.
INT swL2IGMPMulticastVlanRemoveAllMcastAddrListAction	1.3.6.1.4.1.171.11.105.1.2.11.8.1.9	INTEGER	read-write	This object indicates if remove all the multicast address list from the IGMP multicast VLAN or not.
swL2IGMPMulticastVlanGroupTable	1.3.6.1.4.1.171.11.105.1.2.11.9		not-accessible	The table containing the IGMP snooping multicast VLAN group information
swL2IGMPMulticastVlanGroupEntry	1.3.6.1.4.1.171.11.105.1.2.11.9.1		not-accessible	Information about current IGMP snooping multicast VLAN group.
INT swL2IGMPMulticastVlanGroupVid	1.3.6.1.4.1.171.11.105.1.2.11.9.1.1	INTEGER	read-only	This object indicates the Vid of IGMP snooping multicast VLAN group.
IP swL2IGMPMulticastVlanGroupFromIp	1.3.6.1.4.1.171.11.105.1.2.11.9.1.2	IpAddress	read-only	Specifies the multicast address list for this VLAN.
IP swL2IGMPMulticastVlanGroupToIp	1.3.6.1.4.1.171.11.105.1.2.11.9.1.3	IpAddress	read-only	Specifies the multicast address list for this VLAN.
ROW swL2IGMPMulticastVlanGroupStatus	1.3.6.1.4.1.171.11.105.1.2.11.9.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.105.1.2.14
swL2TrafficSegTable	1.3.6.1.4.1.171.11.105.1.2.14.1		not-accessible	This table specifies that the port can just forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.105.1.2.14.1.1		not-accessible	A list of information which specifies the port with its traffic forwarding list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.105.1.2.14.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.105.1.2.14.1.1.2	PortList	read-write	The port list to which the specific port can forward traffic.
swL2MulticastFilterMode	1.3.6.1.4.1.171.11.105.1.2.17
swL2MulticastFilterModeVlanTable	1.3.6.1.4.1.171.11.105.1.2.17.1		not-accessible	A table that contains information about VLAN multicast filter mode.
swL2MulticastFilterModeVlanEntry	1.3.6.1.4.1.171.11.105.1.2.17.1.1		not-accessible	A list of multicast filter mode information for each VLAN.
INT swL2MulticastFilterVid	1.3.6.1.4.1.171.11.105.1.2.17.1.1.1	INTEGER	read-only	Indicates VID for each VLAN.
INT swL2MulticastFilterVlanMode	1.3.6.1.4.1.171.11.105.1.2.17.1.1.2	INTEGER	read-write	Specifies multicast filter mode for each VLAN.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.105.1.2.18
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.105.1.2.18.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.105.1.2.18.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.105.1.2.18.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.105.1.2.18.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
INT swL2LoopDetectMode	1.3.6.1.4.1.171.11.105.1.2.18.1.4	INTEGER	read-write	This object indicates the loopback detection mode for the system.
INT swL2LoopDetectTrapMode	1.3.6.1.4.1.171.11.105.1.2.18.1.5	INTEGER	read-write	This object indicates the loopback detection trap mode for the system.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.105.1.2.18.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.105.1.2.18.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.105.1.2.18.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.105.1.2.18.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.105.1.2.18.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
STR swL2LoopDetectPortLoopVLAN	1.3.6.1.4.1.171.11.105.1.2.18.2.1.1.3	DisplayString	read-only	This object indicates the VLAN list that has detected a loopback.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.105.1.2.18.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.11.105.1.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.11.105.1.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.11.105.1.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.11.105.1.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.11.105.1.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.11.105.1.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.
swL2PPPoEMgmt	1.3.6.1.4.1.171.11.105.1.2.25
INT swL2PPPoECirIDinsertState	1.3.6.1.4.1.171.11.105.1.2.25.1	INTEGER	read-write	This object indicates the status of the PPPoE circuit ID insertion state of the switch.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.105.1.2.100
swL2Notify	1.3.6.1.4.1.171.11.105.1.2.100.1
swL2NotifyMgmt	1.3.6.1.4.1.171.11.105.1.2.100.1.1
AGE swL2macNotificationSeverity	1.3.6.1.4.1.171.11.105.1.2.100.1.1.1	AgentNotifyLevel	read-write	Indicate the level of macNotification detection.
AGE swL2PortSecurityViolationSeverity	1.3.6.1.4.1.171.11.105.1.2.100.1.1.2	AgentNotifyLevel	read-write	Indicate the level of PortSecurityViolation detection.
swL2NotifyPrefix	1.3.6.1.4.1.171.11.105.1.2.100.1.2
swL2NotifFirmware	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0
NTF swL2macNotification	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.1			This trap indicates the MAC addresses variation in address table .
NTF swL2PortSecurityViolationTrap	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.2			When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.3			The trap is sent when Port loop occurred.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.4			The trap is sent when Port loop restart after interval time.
NTF swL2VlanLoopOccurred	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.5			The trap is sent when Port with VID loop occurred.
NTF swL2VlanLoopRestart	1.3.6.1.4.1.171.11.105.1.2.100.1.2.0.6			The trap is sent when Port with VID loop restart after interval time.
swl2NotificationBidings	1.3.6.1.4.1.171.11.105.1.2.100.1.2.1
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.105.1.2.100.1.2.1.1	OCTET STRING	read-only	This object indicates the last time reboot information.
MAC swL2PortSecurityViolationMac	1.3.6.1.4.1.171.11.105.1.2.100.1.2.1.2	MacAddress	accessible-for-notify	This object indicates the MAC address that violates the port security configuration.
INT swL2VlanLoopDetectVID	1.3.6.1.4.1.171.11.105.1.2.100.1.2.1.3	INTEGER	accessible-for-notify	This object indicates the VID that has detected a loopback.

RFC description

Manages Layer 2 features on D-Link DES3528 switches including VLAN, IGMP, spanning tree, and multicast filtering.

Start monitoring D-Link DES-3528 managed switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3528-L2MGMT-MIB

What Is DES3528-L2MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description