DES3028-L2MGMT-MIB

All MIBs › DES3028-L2MGMT-MIB

Organization: D-Link, Inc.

Last Updated: 2010-08-03

Category: VLAN and Bridging, Vendor: D-Link

Description: Covers L2 switching, VLANs, STP, and port security on the D-Link DES-3028 switch.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3028-L2MGMT-MIB?

DES3028-L2MGMT-MIB is a D-Link, Inc. enterprise MIB providing Layer 2 switch management for the DES-3028/3052 (and PoE 'p' variant) switch family, covering device control, per-port configuration, and QoS alongside the standard IF-MIB/BRIDGE-MIB objects. The swL2DevCtrl branch exposes system-level toggles such as IGMP snooping, RMON, LLDP (with an LLDP-disabled forward-message option), VLAN trunking, and MAC address-change notification, while swL2PortCtrlTable configures per-port admin state, N-way speed/duplex negotiation, flow control, address learning, and MDIX mode. Fault and security visibility comes from swL2PortErrTable, which records why a port was error-disabled (stp-lbd, storm-control, ddm, duld) and from spanning-tree-related alarm toggles (swL2DevAlarmNewRoot, swL2DevAlarmTopologyChange, swL2DevAlarmLinkChange), plus per-port/per-priority QoS controls in the swL2QOSMgmt branch (bandwidth rate limiting, 802.1p scheduling and priority mapping, including RADIUS-assigned overrides). It depends on the SWPRIMGMT-DES30XXP-MIB enterprise tree for its OID placement and on RFC1213-MIB/SNMPv2-TC for base types, and it is deployed on D-Link DES-3028/3052 series switches, and administrators can download the DES3028-L2MGMT-MIB file to manage or monitor these switches' Layer 2 behavior.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3028-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3028/3052 switch family (including PoE variants)

Monitoring Examples

An operator polls swL2PortErrPortStatus and swL2PortErrPortReason for each port to spot err-disabled ports, and checks swL2PortInfoLinkStatus alongside swL2DevAlarmTopologyChange; a port stuck err-disabled with reason stp-lbd(1) together with recent topology-change alarms would indicate an STP loopback condition disabling a port to protect the network.

What Can Be Monitored

port error-disable status and reason (loopback, storm-control, DDM, DULD)
port admin/link/speed-duplex status
spanning-tree new-root and topology-change alarms
per-port bandwidth rate limiting
802.1p priority/scheduling configuration
IGMP snooping, LLDP, and VLAN trunking state

Imported Objects

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

From SWPRIMGMT-DES30XXP-MIB

des3028

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.63.6.2			The Structure of Layer 2 Network Management Information for enterprise.
swL2DevMgmt	1.3.6.1.4.1.171.11.63.6.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.63.6.2.1.1
OCT swL2DevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.11.63.6.2.1.1.5	OCTET STRING	read-only	This object is a set of system LED indications. When log in system DES3028/DES3052 which do not support POE, the first two octets is defined as system LED. The first LED is power LED. The second LED is console LED. When log in system DES3028p/DES3052p which support POE, the first four octets are defined as system LED. The first octet is 0x02 and the second octet is 0x01 when in normal mode. Contrarily, the first octet is 0x01 and the second octet is 0x02 when in poe mode. The third octet indicates the power LED. The fourth octet indicates the console LED. The other octets are defined as follow: start on the third or fifth octets separately correspond to system support poe or system which does not support poe indicate the logical port LED (following swL2BasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.11.63.6.2.1.2
INT swL2DevCtrlSystemReboot	1.3.6.1.4.1.171.11.63.6.2.1.2.1	INTEGER	read-write	This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
IP swL2DevCtrlSystemIP	1.3.6.1.4.1.171.11.63.6.2.1.2.2	IpAddress	read-write	This object indicates system ip.
IP swL2DevCtrlSubnetMask	1.3.6.1.4.1.171.11.63.6.2.1.2.3	IpAddress	read-write	This object indicates system subnet mask.
IP swL2DevCtrlDefaultGateway	1.3.6.1.4.1.171.11.63.6.2.1.2.4	IpAddress	read-write	This object indicates system default gateway.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.63.6.2.1.2.5	VlanId	read-write	This object controls which Vlan includes system ip. And the Vlan should have been created.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.63.6.2.1.2.7	INTEGER	read-write	This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.63.6.2.1.2.12	INTEGER	read-write	As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
INT swL2DevCtrlSnmpEnableAuthenTraps	1.3.6.1.4.1.171.11.63.6.2.1.2.13	INTEGER	read-write	Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
INT swL2DevCtrlRmonState	1.3.6.1.4.1.171.11.63.6.2.1.2.16	INTEGER	read-write	This object can be enabled or disabled RMON.
INT swL2DevCtrlIpAutoConfig	1.3.6.1.4.1.171.11.63.6.2.1.2.17	INTEGER	read-write	Indicates the status of automatically getting configuration from TFTP server on device
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.63.6.2.1.2.19	INTEGER	read-write	This object can enabled or disabled MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.63.6.2.1.2.20	INTEGER	read-write	This object indicates the history size of variation MAC in address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.63.6.2.1.2.21	INTEGER	read-write	This object indicates the time interval in second for trigger the MAC notify message.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.63.6.2.1.2.22	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.63.6.2.1.2.23	INTEGER	read-write	When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Units packet will be forwarded.
INT swL2DevCtrlAsymVlanState	1.3.6.1.4.1.171.11.63.6.2.1.2.24	INTEGER	read-write	This object enables or disables the asymmetric VLAN feature of the device.
INT swL2IGMPSnoopingMulticastVlanState	1.3.6.1.4.1.171.11.63.6.2.1.2.25	INTEGER	read-write	This indicates the global state of the igmp_snoop multicast_vlan.
INT swL2DevCtrlVLANTrunkState	1.3.6.1.4.1.171.11.63.6.2.1.2.26	INTEGER	read-write	This indicates the global state of the VLAN trunking feature of the device.
swL2DevCtrlWeb	1.3.6.1.4.1.171.11.63.6.2.1.2.27
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.11.63.6.2.1.2.27.1	INTEGER	read-write	This object controls Web status.
swL2DevCtrlTelnet	1.3.6.1.4.1.171.11.63.6.2.1.2.28
INT swL2DevCtrlTelnetState	1.3.6.1.4.1.171.11.63.6.2.1.2.28.1	INTEGER	read-write	This object controls the Telnet status.
swL2DevAlarm	1.3.6.1.4.1.171.11.63.6.2.1.3
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.171.11.63.6.2.1.3.1	INTEGER	read-write	When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.
INT swL2DevAlarmTopologyChange	1.3.6.1.4.1.171.11.63.6.2.1.3.2	INTEGER	read-write	This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled (3), the Topology Change trap is sent by the device when any of its configured ports transition from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or in another state.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.63.6.2.1.3.3	INTEGER	read-write	This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
swL2PortMgmt	1.3.6.1.4.1.171.11.63.6.2.2
swL2PortInfoTable	1.3.6.1.4.1.171.11.63.6.2.2.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.63.6.2.2.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.63.6.2.2.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoMediumType	1.3.6.1.4.1.171.11.63.6.2.2.1.1.2	INTEGER	read-only	This object indicates the port type: fiber or copper.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.63.6.2.2.1.1.4	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.63.6.2.2.1.1.5	INTEGER	read-only	This object indicates the port speed and duplex mode.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.63.6.2.2.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.63.6.2.2.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.63.6.2.2.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlPortMediumType	1.3.6.1.4.1.171.11.63.6.2.2.2.1.2	INTEGER	read-write	This object indicates the port type: fiber or copper.
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.63.6.2.2.2.1.3	INTEGER	read-write	This object decides whether the port is enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.63.6.2.2.2.1.4	INTEGER	read-write	Choose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.63.6.2.2.2.1.5	INTEGER	read-write	Set the flow control function as enabled or disabled.
STR swL2PortCtrlDescription	1.3.6.1.4.1.171.11.63.6.2.2.2.1.6	DisplayString	read-write	The object describes the ports in text.
INT swL2PortCtrlAddressLearning	1.3.6.1.4.1.171.11.63.6.2.2.2.1.7	INTEGER	read-write	This object decides whether the address learning is enabled or disabled.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.63.6.2.2.2.1.8	INTEGER	read-write	This object sets each port's MAC notification state.
INT swL2PortCtrlMulticastfilter	1.3.6.1.4.1.171.11.63.6.2.2.2.1.9	INTEGER	read-write	This object decides the multicast packet filtering mode on this port.
INT swL2PortCtrlMDIXState	1.3.6.1.4.1.171.11.63.6.2.2.2.1.10	INTEGER	read-write	This object configures the MDIX setting of the port. The value 'other' is for those entries in which MDIX is not applicable.
swL2PortErrTable	1.3.6.1.4.1.171.11.63.6.2.2.3		not-accessible	A table that contains information about the Err port.
swL2PortErrEntry	1.3.6.1.4.1.171.11.63.6.2.2.3.1		not-accessible	A list of information for the err port of the device.
INT swL2PortErrPortIndex	1.3.6.1.4.1.171.11.63.6.2.2.3.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortErrPortState	1.3.6.1.4.1.171.11.63.6.2.2.3.1.2	INTEGER	read-only	This object decides whether the port state is enabled or disabled.
INT swL2PortErrPortStatus	1.3.6.1.4.1.171.11.63.6.2.2.3.1.3	INTEGER	read-only	This object decides whether the PortStatus is err-disabled.
INT swL2PortErrPortReason	1.3.6.1.4.1.171.11.63.6.2.2.3.1.4	INTEGER	read-only	This object indicates the module which disabled the port.
STR swL2PortErrDescription	1.3.6.1.4.1.171.11.63.6.2.2.3.1.5	DisplayString	read-only	The object describes the ports in text.
swL2QOSMgmt	1.3.6.1.4.1.171.11.63.6.2.3
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.11.63.6.2.3.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.11.63.6.2.3.1.1		not-accessible	A list of information contained in swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.11.63.6.2.3.1.1.1	INTEGER	read-only	Indicates the port.
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.11.63.6.2.3.1.1.2	INTEGER	read-write	Indicates the RX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.11.63.6.2.3.1.1.3	INTEGER	read-write	Indicates the TX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.11.63.6.2.3.1.1.4	INTEGER	read-only	The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.11.63.6.2.3.1.1.5	INTEGER	read-only	The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.11.63.6.2.3.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.11.63.6.2.3.2.1		not-accessible	A list of information contained in the swL2QOSSchedulingTable.
INT swL2QOSSchedulingClassIndex	1.3.6.1.4.1.171.11.63.6.2.3.2.1.1	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxWeight	1.3.6.1.4.1.171.11.63.6.2.3.2.1.4	INTEGER	read-write
INT swL2QOSSchedulingMechanism	1.3.6.1.4.1.171.11.63.6.2.3.2.1.5	INTEGER	read-only	Indicates the mechanism of QOS scheduling.
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.11.63.6.2.3.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.11.63.6.2.3.3.1		not-accessible	A list of information contained in the swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.11.63.6.2.3.3.1.1	INTEGER	read-only	The 802.1p user priority.
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.11.63.6.2.3.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.11.63.6.2.3.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.11.63.6.2.3.4.1		not-accessible	A list of information contained in the swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.11.63.6.2.3.4.1.1	INTEGER	read-only	Indicates the port number.
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.11.63.6.2.3.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch.
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.11.63.6.2.3.4.1.3	INTEGER	read-only	Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
INT swL2QOSSchedulingMechanismCtrl	1.3.6.1.4.1.171.11.63.6.2.3.5	INTEGER	read-write	This object can control QOS scheduling Mechanism.
swL2TrunkMgmt	1.3.6.1.4.1.171.11.63.6.2.4
I32 swPortTrunkMaxEntries	1.3.6.1.4.1.171.11.63.6.2.4.1	Integer32	read-only	The max entries of the swPortTrunkTable
I32 swPortTrunkMaxPortMembers	1.3.6.1.4.1.171.11.63.6.2.4.2	Integer32	read-only	The max number of ports allowed in a trunk.
swPortTrunkTable	1.3.6.1.4.1.171.11.63.6.2.4.3		not-accessible	This table specifies the port membership for each logical link.
swPortTrunkEntry	1.3.6.1.4.1.171.11.63.6.2.4.3.1		not-accessible	A list of information that specifies which port group forms a single logical link.
I32 swPortTrunkIndex	1.3.6.1.4.1.171.11.63.6.2.4.3.1.1	Integer32	read-only	The index of logical port trunk.
I32 swPortTrunkMasterPort	1.3.6.1.4.1.171.11.63.6.2.4.3.1.2	Integer32	read-create	The object indicates the master port number of the port trunk entry. The first port of the trunk is implicitly configured to be the master logical port. When using a Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swPortTrunkPortList	1.3.6.1.4.1.171.11.63.6.2.4.3.1.3	PortList	read-create	Indicate member ports of a logical trunk.
INT swPortTrunkType	1.3.6.1.4.1.171.11.63.6.2.4.3.1.4	INTEGER	read-create	This object indicates the type of this entry.
POR swPortTrunkActivePort	1.3.6.1.4.1.171.11.63.6.2.4.3.1.5	PortList	read-only	This object indicates the active ports of this entry.
ROW swPortTrunkState	1.3.6.1.4.1.171.11.63.6.2.4.3.1.6	RowStatus	read-create	This object indicates the status of this entry. when the state is CreatAndGo (4),the type of trunk is static (1); when the state is CreatAndWait (5), the type of trunk is lacp(2).
I32 swPortTrunkFloodingPort	1.3.6.1.4.1.171.11.63.6.2.4.3.1.7	Integer32	read-only	The flooding port of every trunk.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.63.6.2.4.4	INTEGER	read-write	This object configures part of the packet to be examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.11.63.6.2.4.5		not-accessible	This table specifies which port group a set of ports (up to 8) is formed into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.11.63.6.2.4.5.1		not-accessible	A list of information specifies which port group a set of ports (up to 8) is formed into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.11.63.6.2.4.5.1.1	INTEGER	read-only	The index of the logical port LACP.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.11.63.6.2.4.5.1.2	INTEGER	read-write	The state of the logical port LACP.
swL2TrunkVLANTable	1.3.6.1.4.1.171.11.63.6.2.4.6		not-accessible	This table is used to manage the VLAN trunking feature of the device.
swL2TrunkVLANEntry	1.3.6.1.4.1.171.11.63.6.2.4.6.1		not-accessible	This object is used to configure the VLAN trunking settings for each port.
INT swL2TrunkVLANPort	1.3.6.1.4.1.171.11.63.6.2.4.6.1.1	INTEGER	read-only	This object indicates the port being configured.
INT swL2TrunkVLANState	1.3.6.1.4.1.171.11.63.6.2.4.6.1.2	INTEGER	read-write	The state of the logical port LACP.
swPortMirrorPackage	1.3.6.1.4.1.171.11.63.6.2.6
POR swPortMirrorRxPortList	1.3.6.1.4.1.171.11.63.6.2.6.2	PortList	read-write	This object indicates the Rx port list of ports to be sniffed.
POR swPortMirrorTxPortList	1.3.6.1.4.1.171.11.63.6.2.6.3	PortList	read-write	This object indicates the Tx port list of ports to be sniffed.
I32 swPortMirrorTargetPort	1.3.6.1.4.1.171.11.63.6.2.6.4	Integer32	read-write	This object indicates the switch whose port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
INT swPortMirrorState	1.3.6.1.4.1.171.11.63.6.2.6.5	INTEGER	read-write	This object indicates the status of this entry.
swIGMPPackage	1.3.6.1.4.1.171.11.63.6.2.7
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.11.63.6.2.7.1	INTEGER	read-only	The maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPMaxIpGroupNumPerVlan	1.3.6.1.4.1.171.11.63.6.2.7.2	INTEGER	read-only	The maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
swL2IGMPCtrlTable	1.3.6.1.4.1.171.11.63.6.2.7.3		not-accessible	The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN mode is disabled, there is only one entry in the table, with index 1. If VLAN is in Port-Based or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.11.63.6.2.7.3.1		not-accessible	An entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP captures the switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.11.63.6.2.7.3.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Based mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the VID in each entry must be unique in the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.11.63.6.2.7.3.1.2	INTEGER	read-write	The frequency at which IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.11.63.6.2.7.3.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.11.63.6.2.7.3.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.11.63.6.2.7.3.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPHostTimeout	1.3.6.1.4.1.171.11.63.6.2.7.3.1.6	INTEGER	read-write	The timer value for sending IGMP query packets when none was sent by the host in the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query message if the timer expires. Please reference RFC2236-1997.
INT swL2IGMPRouteTimeout	1.3.6.1.4.1.171.11.63.6.2.7.3.1.7	INTEGER	read-write	The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
INT swL2IGMPLeaveTimer	1.3.6.1.4.1.171.11.63.6.2.7.3.1.8	INTEGER	read-write	When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.11.63.6.2.7.3.1.9	INTEGER	read-write	This object decides if the IGMP query is enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.11.63.6.2.7.3.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.11.63.6.2.7.3.1.11	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable (2) - IGMP function is disabled for this entry. enable (3) - IGMP function is enabled for this entry.
INT swL2IGMPFastLeave	1.3.6.1.4.1.171.11.63.6.2.7.3.1.12	INTEGER	read-write
INT swL2IGMPDynIPMultVlanState	1.3.6.1.4.1.171.11.63.6.2.7.3.1.13	INTEGER	read-write	This object is used to disable or enable the dynamic IP multicast feature in this VLAN.
INT swL2IGMPDynIPMultVlanAge	1.3.6.1.4.1.171.11.63.6.2.7.3.1.14	INTEGER	read-write	This object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.11.63.6.2.7.4		not-accessible	The table contains the number of current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.11.63.6.2.7.4.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.11.63.6.2.7.4.1.1	INTEGER	read-only	This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.11.63.6.2.7.4.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function enabled, on a per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.11.63.6.2.7.4.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiring, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
swL2IGMPInfoTable	1.3.6.1.4.1.171.11.63.6.2.7.5		not-accessible	The table containing current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. Also see swL2FilterMgmt description.
swL2IGMPInfoEntry	1.3.6.1.4.1.171.11.63.6.2.7.5.1		not-accessible	Information about current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
INT swL2IGMPVid	1.3.6.1.4.1.171.11.63.6.2.7.5.1.1	INTEGER	read-only	This object indicates the VID of an individual IGMP table entry. It shows the VID of IGMP report information captured on the network.
IP swL2IGMPGroupIpAddr	1.3.6.1.4.1.171.11.63.6.2.7.5.1.2	IpAddress	read-only	This object is the identify group IP address which is captured from IGMP packet, on a per-VLAN basis.
MAC swL2IGMPMacAddr	1.3.6.1.4.1.171.11.63.6.2.7.5.1.3	MacAddress	read-only	This object identifies the MAC address which is corresponding to swL2IGMPGroupIpAddr, on a per-VLAN basis.
POR swL2IGMPPortMap	1.3.6.1.4.1.171.11.63.6.2.7.5.1.4	PortList	read-only	This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string to indicate the port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logic port. If the unit is less than 32 ports, the other port will just fill this value with zeros.
INT swL2IGMPIpGroupReportCount	1.3.6.1.4.1.171.11.63.6.2.7.5.1.5	INTEGER	read-only	This object indicates how many report packets were received by our device corresponding with this entry that has the IGMP function enabled, on a per-VLAN basis.
swL2IGMPRouterPortTable	1.3.6.1.4.1.171.11.63.6.2.7.6		not-accessible	The information of the router port table.
swL2IGMPRouterPortEntry	1.3.6.1.4.1.171.11.63.6.2.7.6.1		not-accessible	The entry of the swL2IGMPRouterPortTable.
INT swL2IGMPRouterPortVlanid	1.3.6.1.4.1.171.11.63.6.2.7.6.1.1	INTEGER	read-only	This object indicates the VLAN ID of the router port entry.
STR swL2IGMPRouterPortVlanName	1.3.6.1.4.1.171.11.63.6.2.7.6.1.2	SnmpAdminString	read-only	This object indicates the VLAN name of the router port entry.
POR swL2IGMPRouterPortStaticPortList	1.3.6.1.4.1.171.11.63.6.2.7.6.1.3	PortList	read-write	This object indicates the static portlist of the router port entry.
POR swL2IGMPRouterPortDynamicPortList	1.3.6.1.4.1.171.11.63.6.2.7.6.1.4	PortList	read-only	This object indicates the dynamic portlist of the router port entry.
POR swL2IGMPRouterPortForbiddenPortList	1.3.6.1.4.1.171.11.63.6.2.7.6.1.5	PortList	read-write	This object indicates the forbidden portlist of the router port entry.
swL2IGMPAccessAuthTable	1.3.6.1.4.1.171.11.63.6.2.7.7		not-accessible	This table is used to manage the IGMP Access Authentication configurations of the device.
swL2IGMPAccessAuthEntry	1.3.6.1.4.1.171.11.63.6.2.7.7.1		not-accessible	A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
INT swL2IGMPAccessAuthPort	1.3.6.1.4.1.171.11.63.6.2.7.7.1.1	INTEGER	read-only	The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
INT swL2IGMPAccessAuthState	1.3.6.1.4.1.171.11.63.6.2.7.7.1.2	INTEGER	read-write	This object denotes the status of IGMP Access Authentication of the port.
swL2IGMPMulticastVlanTable	1.3.6.1.4.1.171.11.63.6.2.7.8		not-accessible	Information about the IGMP snooping multicast VLAN table.
swL2IGMPMulticastVlanEntry	1.3.6.1.4.1.171.11.63.6.2.7.8.1		not-accessible	The entry of swL2IGMPMulticastVlanTable.
INT swL2IGMPMulticastVlanid	1.3.6.1.4.1.171.11.63.6.2.7.8.1.1	INTEGER	read-only	This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
STR swL2IGMPMulticastVlanName	1.3.6.1.4.1.171.11.63.6.2.7.8.1.2	DisplayString	read-create	This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
POR swL2IGMPMulticastVlanSourcePort	1.3.6.1.4.1.171.11.63.6.2.7.8.1.3	PortList	read-write	This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
POR swL2IGMPMulticastVlanMemberPort	1.3.6.1.4.1.171.11.63.6.2.7.8.1.4	PortList	read-write	This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
POR swL2IGMPMulticastVlanTagMemberPort	1.3.6.1.4.1.171.11.63.6.2.7.8.1.5	PortList	read-write	This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
INT swL2IGMPMulticastVlanState	1.3.6.1.4.1.171.11.63.6.2.7.8.1.6	INTEGER	read-write	This object can be used to enable or disable the IGMP snooping multicast VLAN.
IP swL2IGMPMulticastVlanReplaceSourceIp	1.3.6.1.4.1.171.11.63.6.2.7.8.1.7	IpAddress	read-write	The replacement source IP of this multicast VLAN.
ROW swL2IGMPMulticastVlanRowStatus	1.3.6.1.4.1.171.11.63.6.2.7.8.1.8	RowStatus	read-create	This object indicates the status of this entry.
INT swL2IGMPMulticastVlanRemoveAllMcastAddrListAction	1.3.6.1.4.1.171.11.63.6.2.7.8.1.9	INTEGER	read-write	This object indicates whether to remove all the multicast address lists from the IGMP multicast VLAN or not.
POR swL2IGMPMulticastVlanUntagSourcePort	1.3.6.1.4.1.171.11.63.6.2.7.8.1.10	PortList	read-write	This object indicates the untagged member ports to add to the multicast VLAN.
INT swL2IGMPMulticastVlanRemapPriority	1.3.6.1.4.1.171.11.63.6.2.7.8.1.11	INTEGER	read-create	The priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to 8, the packet's original priority will be used.
INT swL2IGMPMulticastVlanReplacePriority	1.3.6.1.4.1.171.11.63.6.2.7.8.1.12	INTEGER	read-create	Specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
swL2IGMPMulticastVlanGroupTable	1.3.6.1.4.1.171.11.63.6.2.7.9		not-accessible	The table containing the IGMP snooping multicast VLAN group information
swL2IGMPMulticastVlanGroupEntry	1.3.6.1.4.1.171.11.63.6.2.7.9.1		not-accessible	Information about the current IGMP snooping multicast VLAN group.
INT swL2IGMPMulticastVlanGroupVid	1.3.6.1.4.1.171.11.63.6.2.7.9.1.1	INTEGER	read-only	This object indicates the VID of the IGMP snooping multicast VLAN group.
IP swL2IGMPMulticastVlanGroupFromIp	1.3.6.1.4.1.171.11.63.6.2.7.9.1.2	IpAddress	read-only	Specifies the multicast address list for this VLAN.
IP swL2IGMPMulticastVlanGroupToIp	1.3.6.1.4.1.171.11.63.6.2.7.9.1.3	IpAddress	read-only	Specifies the multicast address list for this VLAN.
ROW swL2IGMPMulticastVlanGroupStatus	1.3.6.1.4.1.171.11.63.6.2.7.9.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2IGMPv3Table	1.3.6.1.4.1.171.11.63.6.2.7.10		not-accessible	This table contains the IGMP snooping V3 information.
swL2IGMPv3Entry	1.3.6.1.4.1.171.11.63.6.2.7.10.1		not-accessible	Information about the current IGMP snooping V3.
IP swL2IGMPv3SourceIPAddr	1.3.6.1.4.1.171.11.63.6.2.7.10.1.1	IpAddress	read-only	This object identifies the source IP addresses from the group where they were captured from. IGMP packets, on a per-VLAN basis.
INT swL2IGMPv3Forwarding	1.3.6.1.4.1.171.11.63.6.2.7.10.1.2	INTEGER	read-only	This object identifies if the packets from the source IP addresses are forwarding or not.
INT swL2IGMPv3ExpireTimer	1.3.6.1.4.1.171.11.63.6.2.7.10.1.3	INTEGER	read-only	This object identifies the leaving times of the source time.
swIGMPSnoopingGroupTable	1.3.6.1.4.1.171.11.63.6.2.7.11		not-accessible	The table contains the current IGMP snooping group information captured by the device.
swIGMPSnoopingGroupEntry	1.3.6.1.4.1.171.11.63.6.2.7.11.1		not-accessible	Information about the current IGMP snooping group information which has been captured by the device.
INT swIGMPSnoopingGroupVid	1.3.6.1.4.1.171.11.63.6.2.7.11.1.1	INTEGER	read-only	This object indicates the VID of the individual IGMP snooping group table entry.
IP swIGMPSnoopingGroupGroupAddr	1.3.6.1.4.1.171.11.63.6.2.7.11.1.2	IpAddress	read-only	This object identifies the group IP address which has been captured from the IGMP packet, on a per-VLAN basis.
IP swIGMPSnoopingGroupSourceAddr	1.3.6.1.4.1.171.11.63.6.2.7.11.1.3	IpAddress	read-only	This object identifies the source addresses.
POR swIGMPSnoopingGroupIncludePortMap	1.3.6.1.4.1.171.11.63.6.2.7.11.1.4	PortList	read-only	This object indicates the port list under INCLUDE mode.
POR swIGMPSnoopingGroupExcludePortMap	1.3.6.1.4.1.171.11.63.6.2.7.11.1.5	PortList	read-only	This object indicates the port list under EXCLUDE mode.
INT swIGMPSnoopingGroupReportCount	1.3.6.1.4.1.171.11.63.6.2.7.11.1.6	INTEGER	read-only	This object indicates how many report packets were received by our device corresponding with this entry that has the IGMP function enabled, on a per-group basis.
TIK swIGMPSnoopingGroupUpTime	1.3.6.1.4.1.171.11.63.6.2.7.11.1.7	TimeTicks	read-only	This object indicates how long since the group was detected.
TIK swIGMPSnoopingGroupExpiryTime	1.3.6.1.4.1.171.11.63.6.2.7.11.1.8	TimeTicks	read-only	This object indicates the time left before this group will be aged out.
POR swIGMPSnoopingGroupRouterPorts	1.3.6.1.4.1.171.11.63.6.2.7.11.1.9	PortList	read-only	This object indicates the port number of the router ports.
swL2IGMPDynIpMultMgmt	1.3.6.1.4.1.171.11.63.6.2.7.12
INT swL2IGMPDynIPMultMaxEntry	1.3.6.1.4.1.171.11.63.6.2.7.12.1	INTEGER	read-write	This object specifies the maximum number of entries which can be learned by dynamic IP multicast.
swL2IGMPSnoopingClearDynIpMult	1.3.6.1.4.1.171.11.63.6.2.7.12.2
VLA swL2IGMPSnoopingClearDynIpMultVID	1.3.6.1.4.1.171.11.63.6.2.7.12.2.1	VlanId	read-write	This object indicates the VLAN identifier where the data driven entries will be removed from.
IP swL2IGMPSnoopingClearDynIpMultIP	1.3.6.1.4.1.171.11.63.6.2.7.12.2.2	IpAddress	read-write	This object indicates the IP address of the IGMP snooping group from which the data driven entries will be removed.
INT swL2IGMPSnoopingClearDynIpMultAction	1.3.6.1.4.1.171.11.63.6.2.7.12.2.3	INTEGER	read-write	Setting this object will clear the data driven entries. all - Remove all learned data driven groups. VLAN - Clear all data driven entries in the VLAN specified in swIGMPSnoopingClearDynIpMultVID. group - Clear the group with the address specified in swL2IGMPSnoopingClearDynIpMultIP in the VLAN specified in swIGMPSnoopingClearDynIpMultVID.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.63.6.2.12
swL2TrafficSegTable	1.3.6.1.4.1.171.11.63.6.2.12.1		not-accessible	This table specifies the port just can forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.63.6.2.12.1.1		not-accessible	A list of information specifies the port with its traffic forward list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.63.6.2.12.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.63.6.2.12.1.1.2	PortList	read-write	The port list that the specific port can forward traffic.
swL2PortSecurityMgmt	1.3.6.1.4.1.171.11.63.6.2.15
swL2PortSecurityControlTable	1.3.6.1.4.1.171.11.63.6.2.15.1		not-accessible	The port security feature controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as a static entry. When the learned address number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.11.63.6.2.15.1.1		not-accessible	A list of information contained in the swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.11.63.6.2.15.1.1.1	INTEGER	read-only	Indicates a secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.11.63.6.2.15.1.1.2	INTEGER	read-write	Indicates the allowable number of addresses to be learned at this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.11.63.6.2.15.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout (3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset (4) mode - never age out the locked addresses unless restarting the system to prevent port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.11.63.6.2.15.1.1.4	INTEGER	read-write	Indicates an administration state of locking address.
INT swL2PortSecurityTrapLogState	1.3.6.1.4.1.171.11.63.6.2.15.2	INTEGER	read-write	When enabled (2), whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in the system.
swL2PortSecurityDelCtrl	1.3.6.1.4.1.171.11.63.6.2.15.3
STR swL2PortSecurityDelVlanName	1.3.6.1.4.1.171.11.63.6.2.15.3.1	DisplayString	read-write	Indicates the VLAN name.
INT swL2PortSecurityDelPort	1.3.6.1.4.1.171.11.63.6.2.15.3.2	INTEGER	read-write	Indicates the port. 0 means the function dose not work now.
MAC swL2PortSecurityDelMacAddress	1.3.6.1.4.1.171.11.63.6.2.15.3.3	MacAddress	read-write	Specifies the MAC address.
INT swL2PortSecurityDelActivity	1.3.6.1.4.1.171.11.63.6.2.15.3.4	INTEGER	read-write
swL2CosMgmt	1.3.6.1.4.1.171.11.63.6.2.17
swL2CosPriorityCtrl	1.3.6.1.4.1.171.11.63.6.2.17.3
swL2CosPriorityTable	1.3.6.1.4.1.171.11.63.6.2.17.3.1		not-accessible	Used to show and configure per port priority-based QoS features on the switch.
swL2CosPriorityEntry	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1		not-accessible	A list of information contained in the swL2CosPriorityTable.
INT swL2CosPriorityPort	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.1	INTEGER	read-only	The port number of CoS Priority.
INT swL2CosPriorityPortPRI	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.2	INTEGER	read-write	Indicates the port_priority state for CoS.
INT swL2CosPriorityEtherPRI	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.3	INTEGER	read-write	Enable Ethernet frame based priority. When set ether8021p (2), enable 802.1p QoS; When set macBase (3), enable MAC-based QoS; When set disable (1), disable Ethernet frame based priority.
INT swL2CosPriorityIpPRI	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.4	INTEGER	read-write	Enable IP priority QoS. When set tos (2), enable TOS based QoS; When set dscp (3), enable DSCP based QoS; When set disable (1), disable IP priority QoS.
INT swL2CosPriorityNone	1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.5	INTEGER	read-write	When read, it always returns invalid (2); when write valid (1), it disables all priority in this table.
swL2CosPortPRITable	1.3.6.1.4.1.171.11.63.6.2.17.3.2		not-accessible	Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.
swL2CosPortPRIEntry	1.3.6.1.4.1.171.11.63.6.2.17.3.2.1		not-accessible	A list of information contained in the swL2CosPortPRITable.
INT swL2CosPortPRIIndex	1.3.6.1.4.1.171.11.63.6.2.17.3.2.1.1	INTEGER	read-only	Indicates the CoS Priority PortPRI.
INT swL2CosPortPRIClass	1.3.6.1.4.1.171.11.63.6.2.17.3.2.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges. And you can set a value of 0 or 3 only, you can't set a value 1 or 2.
swL2CosMacBasePRITable	1.3.6.1.4.1.171.11.63.6.2.17.3.3		not-accessible	Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.
swL2CosMacBasePRIEntry	1.3.6.1.4.1.171.11.63.6.2.17.3.3.1		not-accessible	A list of information contained in the swL2CosMacBasePRITable.
MAC swL2CosMacBasePRIIndex	1.3.6.1.4.1.171.11.63.6.2.17.3.3.1.1	MacAddress	read-only	Indicates the CoS Priority MacBasePRI.
INT swL2CosMacBasePRIClass	1.3.6.1.4.1.171.11.63.6.2.17.3.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
swL2CosTosPRITable	1.3.6.1.4.1.171.11.63.6.2.17.3.4		not-accessible	Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
swL2CosTosPRIEntry	1.3.6.1.4.1.171.11.63.6.2.17.3.4.1		not-accessible	A list of information contained in the swL2CosTosPRITable.
INT swL2CosTosPRIIndex	1.3.6.1.4.1.171.11.63.6.2.17.3.4.1.1	INTEGER	read-only	Indicates the CoS Priority TosPRI.
INT swL2CosTosPRIClass	1.3.6.1.4.1.171.11.63.6.2.17.3.4.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
swL2CosDscpPRITable	1.3.6.1.4.1.171.11.63.6.2.17.3.5		not-accessible	Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
swL2CosDscpPRIEntry	1.3.6.1.4.1.171.11.63.6.2.17.3.5.1		not-accessible	A list of information contained in the swL2CosDscpPRITable.
INT swL2CosDscpPRIIndex	1.3.6.1.4.1.171.11.63.6.2.17.3.5.1.1	INTEGER	read-only	Indicates the CoS Priority DscpPRI.
INT swL2CosDscpPRIClass	1.3.6.1.4.1.171.11.63.6.2.17.3.5.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
swL2DhcpRelayMgmt	1.3.6.1.4.1.171.11.63.6.2.18
INT swL2DhcpRelayState	1.3.6.1.4.1.171.11.63.6.2.18.1	INTEGER	read-write	This object indicates whether the DHCP relay function is enabled or disabled.
INT swL2DhcpRelayHopCount	1.3.6.1.4.1.171.11.63.6.2.18.2	INTEGER	read-write	This object indicates the maximum number of router hops that the DHCP packets can cross.
INT swL2DhcpRelayTimeThreshold	1.3.6.1.4.1.171.11.63.6.2.18.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
INT swL2DhcpRelayOption82State	1.3.6.1.4.1.171.11.63.6.2.18.4	INTEGER	read-write	This object indicates DHCP relay agent information option 82 function is enabled or disabled.
INT swL2DhcpRelayOption82Check	1.3.6.1.4.1.171.11.63.6.2.18.5	INTEGER	read-write	This object indicates the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
INT swL2DhcpRelayOption82Policy	1.3.6.1.4.1.171.11.63.6.2.18.6	INTEGER	read-write	This object indicates the reforwarding policy of DHCP relay agent information option 82. replace (1) - Replace the exiting option 82 field in messages. drop (2) - Discard messages with existing option 82 field. keep (3) - Retain the existing option 82 field in messages.
swL2DhcpRelayCtrlTable	1.3.6.1.4.1.171.11.63.6.2.18.7		not-accessible	This table specifies the IP address as a destination to forward (relay) DHCP packets to.
swL2DhcpRelayCtrlEntry	1.3.6.1.4.1.171.11.63.6.2.18.7.1		not-accessible	A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
STR swL2DhcpRelayCtrlInterfaceName	1.3.6.1.4.1.171.11.63.6.2.18.7.1.1	DisplayString	read-only	The name of the IP interface.
IP swL2DhcpRelayCtrlServer	1.3.6.1.4.1.171.11.63.6.2.18.7.1.2	IpAddress	read-only	The DHCP server IP address.
INT swL2DhcpRelayCtrlState	1.3.6.1.4.1.171.11.63.6.2.18.7.1.3	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) - Writing this value to the object, and then the corresponding entry will be removed from the table. valid (3) - This entry resides in the table.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.63.6.2.20
swL2MgmtMIBTrapPrefix	1.3.6.1.4.1.171.11.63.6.2.20.0
NTF swL2PortSecurityViolationTrap	1.3.6.1.4.1.171.11.63.6.2.20.0.1			When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out.
NTF swL2macNotification	1.3.6.1.4.1.171.11.63.6.2.20.0.2			This trap indicates the MAC address variations in the address table.
NTF swL2FloodMacDetectedTrap	1.3.6.1.4.1.171.11.63.6.2.20.0.3			If theres a new flooding MAC is detected, a trap will be sent out.
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.11.63.6.2.20.0.4			The trap is sent when a Port loop occurs.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.11.63.6.2.20.0.5			The trap is sent when a Port loop restarts after the interval time.
swl2PortSecurityBindings	1.3.6.1.4.1.171.11.63.6.2.20.1
MAC swL2PortSecurityViolationMac	1.3.6.1.4.1.171.11.63.6.2.20.1.1	MacAddress	accessible-for-notify	This object indicates the MAC address that violates the port security configuration.
swl2NotificationBindings	1.3.6.1.4.1.171.11.63.6.2.20.2
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.63.6.2.20.2.1	OCTET STRING	read-only	This object indicates the last time reboot information.
INT swL2FloodMacDetectedMacVid	1.3.6.1.4.1.171.11.63.6.2.20.2.2	INTEGER	read-only	This object indicates the VID of the flooding MAC.
MAC swL2FloodMacDetectedMacAddress	1.3.6.1.4.1.171.11.63.6.2.20.2.3	MacAddress	read-only	This object indicates the MAC address of the flooding MAC
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.63.6.2.21
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.63.6.2.21.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.63.6.2.21.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.63.6.2.21.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.63.6.2.21.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
INT swL2LoopDetectTrapMode	1.3.6.1.4.1.171.11.63.6.2.21.1.5	INTEGER	read-write	This object indicates the loopback detection trap mode for the system.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.63.6.2.21.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.63.6.2.21.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.63.6.2.21.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2MultiFilter	1.3.6.1.4.1.171.11.63.6.2.22
swL2McastFilterTable	1.3.6.1.4.1.171.11.63.6.2.22.2		not-accessible	A table that contains information about the multicast filter address.
swL2McastFilterEntry	1.3.6.1.4.1.171.11.63.6.2.22.2.1		not-accessible	A list of multicast filter mode information for each profile ID.
INT swL2McastFilterProfileIndex	1.3.6.1.4.1.171.11.63.6.2.22.2.1.1	INTEGER	read-only	index for each profile
STR swL2McastFilterProfileName	1.3.6.1.4.1.171.11.63.6.2.22.2.1.2	DisplayString	read-write	The multicast filter description.
INT swL2McastFilterAddOrDelState	1.3.6.1.4.1.171.11.63.6.2.22.2.1.3	INTEGER	read-write	The control multicast filter address.
STR swL2McastFilterGroupList	1.3.6.1.4.1.171.11.63.6.2.22.2.1.4	DisplayString	read-write	The multicast filter address group list.
ROW swL2McastFilterStatus	1.3.6.1.4.1.171.11.63.6.2.22.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL2McastFilterPortTable	1.3.6.1.4.1.171.11.63.6.2.22.3		not-accessible	A table that is used to bind port to profile ID.
swL2McastFilterPortEntry	1.3.6.1.4.1.171.11.63.6.2.22.3.1		not-accessible	A list of information that is used to bind port to profile ID.
INT swL2McastFilterPortGroupPortIndex	1.3.6.1.4.1.171.11.63.6.2.22.3.1.1	INTEGER	read-only	The port index.
INT swL2McastFilterPortProfileAddOrDelState	1.3.6.1.4.1.171.11.63.6.2.22.3.1.2	INTEGER	read-write	The control multicast filter profile.
INT swL2McastFilterPortProfileID	1.3.6.1.4.1.171.11.63.6.2.22.3.1.3	INTEGER	read-write	This object indicates the profile ID of this entry. When read, it is always 0. When set, 0 can not be set.
swL2McastFilterPortMaxGroupTable	1.3.6.1.4.1.171.11.63.6.2.22.4		not-accessible	A table that contains information about the max group number based on port.
swL2McastFilterPortMaxGroupEntry	1.3.6.1.4.1.171.11.63.6.2.22.4.1		not-accessible	A list of max group number information for each port.
INT swL2McastFilterPortMaxGroupPortIndex	1.3.6.1.4.1.171.11.63.6.2.22.4.1.1	INTEGER	read-only	The port index.
INT swL2McastFilterPortMaxGroup	1.3.6.1.4.1.171.11.63.6.2.22.4.1.2	INTEGER	read-write	The max group numbers. The default is 256.
swL2McastFilterPortInfoTable	1.3.6.1.4.1.171.11.63.6.2.22.5		not-accessible	A table that contains information about all of the multicast groups for the ports.
swL2McastFilterPortInfoEntry	1.3.6.1.4.1.171.11.63.6.2.22.5.1		not-accessible	A list of information about all of the multicast groups for each port.
INT swL2McastFilterPortInfoPortIndex	1.3.6.1.4.1.171.11.63.6.2.22.5.1.1	INTEGER	read-only	The port index.
STR swL2McastFilterPortInfoProfileName	1.3.6.1.4.1.171.11.63.6.2.22.5.1.2	DisplayString	read-only	The multicast filter address profile Name.
swL2VlanMgmt	1.3.6.1.4.1.171.11.63.6.2.23
swL2VlanAdvertisementTable	1.3.6.1.4.1.171.11.63.6.2.23.1		not-accessible	A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
swL2VlanAdvertisementEntry	1.3.6.1.4.1.171.11.63.6.2.23.1.1		not-accessible	The advertisement state for each VLAN configured into the device.
INT swL2VlanIndex	1.3.6.1.4.1.171.11.63.6.2.23.1.1.1	INTEGER	read-only	The VLAN-ID or other identifier referring to this VLAN.
STR swL2VlanName	1.3.6.1.4.1.171.11.63.6.2.23.1.1.2	DisplayString	read-only	An administratively assigned string, which may be used to identify the VLAN.
INT swL2VlanAdvertiseState	1.3.6.1.4.1.171.11.63.6.2.23.1.1.3	INTEGER	read-write	This object indicates the advertise status of this VLAN entry.
swL2VlanMultiplyMgmt	1.3.6.1.4.1.171.11.63.6.2.23.2
STR swL2VlanMultiplyVlanList	1.3.6.1.4.1.171.11.63.6.2.23.2.1	DisplayString	read-write	This object specifies the VLAN ID List.
INT swL2VlanMultiplyAdvertisement	1.3.6.1.4.1.171.11.63.6.2.23.2.2	INTEGER	read-write	This object specifies the advertisement state.
POR swL2VlanMultiplyPortList	1.3.6.1.4.1.171.11.63.6.2.23.2.3	PortList	read-write	Specifies the port list.
INT swL2VlanMultiplyPortListAction	1.3.6.1.4.1.171.11.63.6.2.23.2.4	INTEGER	read-write	Specifies the action for the port list which specified by swL2VlanMultiplyPortList.
INT swL2VlanMultiplyAction	1.3.6.1.4.1.171.11.63.6.2.23.2.5	INTEGER	read-write	Specifies the action for VLANs. other: no action. create: the VLANs specified by swL2VlanMultiplyVlanList would be created at a time. configure: the VLANs specified by swL2VlanMultiplyVlanList would be configured at a time. delete: the VLANs specified by swL2VlanMultiplyVlanList would be deleted at a time.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.11.63.6.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.11.63.6.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.11.63.6.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.11.63.6.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.11.63.6.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.11.63.6.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.
swL2FloodMAC	1.3.6.1.4.1.171.11.63.6.2.25
swL2FloodMACMgmt	1.3.6.1.4.1.171.11.63.6.2.25.1
swL2FloodMACGlobalSettings	1.3.6.1.4.1.171.11.63.6.2.25.1.1
INT swL2FloodMACState	1.3.6.1.4.1.171.11.63.6.2.25.1.1.1	INTEGER	read-write	This object indicates the status of Flooding MAC function.
INT swL2FloodMACLogState	1.3.6.1.4.1.171.11.63.6.2.25.1.1.2	INTEGER	read-write	This object indicates whether logs are generated when a flooding MAC is detected.
INT swL2FloodMACTrapState	1.3.6.1.4.1.171.11.63.6.2.25.1.1.3	INTEGER	read-write	This object indicates whether traps are generated when a flooding MAC is detected.
INT swL2FloodMACClearFDB	1.3.6.1.4.1.171.11.63.6.2.25.1.1.4	INTEGER	read-write	When set to start(2), this object will clear the entries of swL2FloodMACFDBTable. After the device finishes clearing the entries, it will return to its default value, no-action(1). Setting this object to no-action(1) will not have any effect.
swL2FloodMACAutoFDBCtrlTable	1.3.6.1.4.1.171.11.63.6.2.25.1.2		not-accessible	A table containing a list of configured IP addresses to which the Auto FDB function will discover the corresponding VLAN, MAC address and port and have a corresponding static FDB entry created automatically.
swL2FloodMACAutoFDBCtrlEntry	1.3.6.1.4.1.171.11.63.6.2.25.1.2.1		not-accessible	Information containing the configured Auto FDB IP address.
IP swL2FloodMACAutoFDBIPAddress	1.3.6.1.4.1.171.11.63.6.2.25.1.2.1.1	IpAddress	not-accessible	The Auto FDB IP address.
ROW swL2FloodMACAutoFDBRowStatus	1.3.6.1.4.1.171.11.63.6.2.25.1.2.1.2	RowStatus	read-create	This object indicates the status of this entry.
swL2FloodMACInfo	1.3.6.1.4.1.171.11.63.6.2.25.2
swL2FloodMACFDBTable	1.3.6.1.4.1.171.11.63.6.2.25.2.1		not-accessible	A table containing a list of current and historical flooding MAC entries.
swL2FloodMACFDBEntry	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1		not-accessible	Information containing the flooding MAC address.
INT swL2FloodMACFDBIndex	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1.1	INTEGER	not-accessible	The hardware address table index of the flooding MAC entry.
INT swL2FloodMACFDBVID	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1.2	INTEGER	not-accessible	The VLAN identifier of the flooding MAC entry.
MAC swL2FloodMACFDBMacAddress	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1.3	MacAddress	not-accessible	The MAC address of the flooding MAC entry.
INT swL2FloodMACFDBStatus	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1.4	INTEGER	read-only	The status of the flooding MAC entry. When the value is 'active', this means the entry is currently present in the hardware address table, otherwise, the value is 'inactive'.
INT swL2FloodMACFDBTimestamp	1.3.6.1.4.1.171.11.63.6.2.25.2.1.1.5	INTEGER	read-only	A number that correlates to a relative time the entry was detected by the Flooding MAC function.
swL2FloodMACAutoFDBTable	1.3.6.1.4.1.171.11.63.6.2.25.2.2		not-accessible	A table containing the discovered VLAN, MAC address and port of the host with an IP address created in swL2FloodMACAutoFDBCtrlTable.
swL2FloodMACAutoFDBEntry	1.3.6.1.4.1.171.11.63.6.2.25.2.2.1		not-accessible	Information containing the discovered VLAN, MAC address and port of an Auto FDB entry.
INT swL2FloodMACAutoFDBVID	1.3.6.1.4.1.171.11.63.6.2.25.2.2.1.1	INTEGER	read-only	The VLAN identifier of Auto FDB entry.
MAC swL2FloodMACAutoFDBMacAddress	1.3.6.1.4.1.171.11.63.6.2.25.2.2.1.2	MacAddress	read-only	The MAC address of the Auto FDB entry.
INT swL2FloodMACAutoFDBPort	1.3.6.1.4.1.171.11.63.6.2.25.2.2.1.3	INTEGER	read-only	The port number of the Auto FDB entry.
INT swL2FloodMACAutoFDBTimestamp	1.3.6.1.4.1.171.11.63.6.2.25.2.2.1.4	INTEGER	read-only	A number that represents the relative time when the Auto FDB learned this entry.

RFC description

Manages L2 switching, VLANs, STP, and port security for D-Link DES-3028 switch.

Start monitoring D-Link DES-3028/3052 switch family (PoE variants) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3028-L2MGMT-MIB

What Is DES3028-L2MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description