DES-1526-MIB

All MIBs › DES-1526-MIB

Category: VLAN and Bridging, Vendor: D-Link

Description: Manages D-Link DES-1526 24-port smart switch L2 configuration, VLANs, and spanning tree.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES-1526-MIB?

DES-1526-MIB is the device-specific enterprise MIB for the D-Link DES-1526, a 24-port smart managed switch, covering Layer 2 configuration such as VLANs and spanning tree for that specific product line. As with similar D-Link smart-switch MIBs, it would be expected to expose VLAN membership, spanning-tree protocol state, and basic port configuration objects rather than deep hardware sensors or advanced routing features. No concrete object or table names were available in this extract, so specific monitored parameters cannot be confirmed with certainty here. It would typically complement standard IF-MIB and BRIDGE-MIB objects for full interface and bridging visibility on the switch. It is deployed in small business or branch environments using the D-Link DES-1526 switch for basic managed Layer 2 networking. Engineers can download the DES-1526-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES-1526-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-1526 smart switch

Monitoring Examples

No sample object names were available in this extract, so a concrete polling scenario cannot be honestly constructed. Typically a MIB of this kind would be polled for VLAN membership and spanning-tree port state, but specifics are not confirmed for this module.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
PhysAddress
mib-2

OIDs

OID symbolic	OID numeric	Type	Access	Description
d_link	1.3.6.1.4.1.171
dlink_products	1.3.6.1.4.1.171.10
dlink_DES1526SeriesProd	1.3.6.1.4.1.171.10.60
DES_1526	1.3.6.1.4.1.171.10.60.1
NTF swFiberInsert	1.3.6.1.4.1.171.10.60.1.0.1			Fiber insert trap
NTF swFiberRemove	1.3.6.1.4.1.171.10.60.1.0.2			Fiber remove trap
NTF swFiberAbnormalRXError	1.3.6.1.4.1.171.10.60.1.0.3			Fiber abnormal rx error trap
NTF swFiberAbnormalTXError	1.3.6.1.4.1.171.10.60.1.0.4			Fiber abnormal tx error trap
NTF swTPAbnormalRXError	1.3.6.1.4.1.171.10.60.1.0.5			Twisted Pair abnormal rx error trap
NTF swTPAbnormalTXError	1.3.6.1.4.1.171.10.60.1.0.6			Twisted Pair abnormal tx error trap
companyCommGroup	1.3.6.1.4.1.171.10.60.1.1
commSetTable	1.3.6.1.4.1.171.10.60.1.1.1		not-accessible	A list of SNMP Set Community Entries
commSetEntry	1.3.6.1.4.1.171.10.60.1.1.1.1		not-accessible	A list of SNMP Set Community properties
INT commSetIndex	1.3.6.1.4.1.171.10.60.1.1.1.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commSetName	1.3.6.1.4.1.171.10.60.1.1.1.1.2	DisplayString	read-write	The name of this SNMP Set Community Entry.
ROW commSetStatus	1.3.6.1.4.1.171.10.60.1.1.1.1.3	RowStatus	read-write	The RowStatus for the Set Community entry.
commGetTable	1.3.6.1.4.1.171.10.60.1.1.2		not-accessible	A list of SNMP Get Community Entries
commGetEntry	1.3.6.1.4.1.171.10.60.1.1.2.1		not-accessible	A list of SNMP Get Community properties
INT commGetIndex	1.3.6.1.4.1.171.10.60.1.1.2.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commGetName	1.3.6.1.4.1.171.10.60.1.1.2.1.2	DisplayString	read-write	The name of this SNMP Get Community Entry.
ROW commGetStatus	1.3.6.1.4.1.171.10.60.1.1.2.1.3	RowStatus	read-write	The RowStatus for the Get Community entry.
commTrapTable	1.3.6.1.4.1.171.10.60.1.1.3		not-accessible	A list of SNMP Trap Community Entries
commTrapEntry	1.3.6.1.4.1.171.10.60.1.1.3.1		not-accessible	A list of SNMP Trap Community properties
INT commTrapIndex	1.3.6.1.4.1.171.10.60.1.1.3.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
STR commTrapName	1.3.6.1.4.1.171.10.60.1.1.3.1.2	DisplayString	read-write	The name of this SNMP Trap Community Entry.
IP commTrapIpAddress	1.3.6.1.4.1.171.10.60.1.1.3.1.3	IpAddress	read-write	The IP Address of this SNMP Trap Community Entry.
INT commTrapVlanId	1.3.6.1.4.1.171.10.60.1.1.3.1.4	INTEGER	read-write	The Trap VLAN identifier of this SNMP Trap Community Entry. The value must be from 1 to 4094.
INT commTrapSNMPBootup	1.3.6.1.4.1.171.10.60.1.1.3.1.5	INTEGER	read-write	Bootup trap
INT commTrapSNMPTPLinkUpDown	1.3.6.1.4.1.171.10.60.1.1.3.1.6	INTEGER	read-write	Twisted Pair link up / link down trap
INT commTrapSNMPFiberLinkUpDown	1.3.6.1.4.1.171.10.60.1.1.3.1.7	INTEGER	read-write	Fiber link up / link down trap
INT commTrapTrapAbnormalTPRXError	1.3.6.1.4.1.171.10.60.1.1.3.1.9	INTEGER	read-write	Twisted Pair abnormal receive error trap
INT commTrapTrapAbnormalTPTXError	1.3.6.1.4.1.171.10.60.1.1.3.1.10	INTEGER	read-write	Twisted Pair abnormal transmit error trap
INT commTrapTrapAbnormalFiberRXError	1.3.6.1.4.1.171.10.60.1.1.3.1.11	INTEGER	read-write	Fiber abnormal receive error trap
INT commTrapTrapAbnormalFiberTXError	1.3.6.1.4.1.171.10.60.1.1.3.1.12	INTEGER	read-write	Fiber abnormal transmit error trap
INT commTrapTrapPOEPowerFail	1.3.6.1.4.1.171.10.60.1.1.3.1.13	INTEGER	read-write	PoE POWER Fail
INT commTrapTrapPOEPortOvercurrent	1.3.6.1.4.1.171.10.60.1.1.3.1.14	INTEGER	read-write	PoE port Overcurrent
INT commTrapTrapPOEPortShort	1.3.6.1.4.1.171.10.60.1.1.3.1.15	INTEGER	read-write	PoE port Shortcircuit
ROW commTrapStatus	1.3.6.1.4.1.171.10.60.1.1.3.1.16	RowStatus	read-write	The RowStatus for the Trap Community entry.
companyMiscGroup	1.3.6.1.4.1.171.10.60.1.3
INT miscStatisticsReset	1.3.6.1.4.1.171.10.60.1.3.3	INTEGER	read-write	Resets the units statistics. A (1) resets the unit, a (2) does nothing.
companyConfigGroup	1.3.6.1.4.1.171.10.60.1.11
STR configVerSwPrimary	1.3.6.1.4.1.171.10.60.1.11.1	DisplayString	read-only	The software image version string
STR configVerHwChipSet	1.3.6.1.4.1.171.10.60.1.11.2	DisplayString	read-only	The hardware chipset version string
configPortTable	1.3.6.1.4.1.171.10.60.1.11.6		not-accessible	A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces.
configPortEntry	1.3.6.1.4.1.171.10.60.1.11.6.1		not-accessible	An enterprise specific interface entry.
INT configPort	1.3.6.1.4.1.171.10.60.1.11.6.1.1	INTEGER	read-only	A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber.
INT configPortSpeed	1.3.6.1.4.1.171.10.60.1.11.6.1.2	INTEGER	read-write	The port's speed desired state.
INT configPortOperStatus	1.3.6.1.4.1.171.10.60.1.11.6.1.3	INTEGER	read-only	The port's operating speed state.
INT configPortFlowControl	1.3.6.1.4.1.171.10.60.1.11.6.1.4	INTEGER	read-write	The port will avoid transmitting a new packet for the period of time specified in a received PAUSE packet when enabled.
INT configPortFlowControlOper	1.3.6.1.4.1.171.10.60.1.11.6.1.5	INTEGER	read-only	The port's operating flow control state.
INT configPortPriority	1.3.6.1.4.1.171.10.60.1.11.6.1.6	INTEGER	read-write	The port's current priority.
configMirrorTable	1.3.6.1.4.1.171.10.60.1.11.8		not-accessible	A list of the Mirror
configMirrorEntry	1.3.6.1.4.1.171.10.60.1.11.8.1		not-accessible	A Mirror entry containing the Mirror id and mode
INT configMirrorId	1.3.6.1.4.1.171.10.60.1.11.8.1.1	INTEGER	read-only	An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported.
INT configMirrorMode	1.3.6.1.4.1.171.10.60.1.11.8.1.2	INTEGER	read-write	When deciding the mirroring source port, then Mirror mode will be available.
INT configMirrorMon	1.3.6.1.4.1.171.10.60.1.11.8.1.3	INTEGER	read-write	When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled.
POR configMirrorSrc	1.3.6.1.4.1.171.10.60.1.11.8.1.4	PortList	read-write	When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring source port. This value has a valid range of 1 to ifNumber when enbaled. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
ROW configMirrorStatus	1.3.6.1.4.1.171.10.60.1.11.8.1.5	RowStatus	read-write	The RowStatus for the Mirror entry.
INT configSNMPEnable	1.3.6.1.4.1.171.10.60.1.11.9	INTEGER	read-write	Enable/Disable SNMP function. A (1) enables, a (2) disables.
INT configIpAssignmentMode	1.3.6.1.4.1.171.10.60.1.11.12	INTEGER	read-write	Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP).
MAC configPhysAddress	1.3.6.1.4.1.171.10.60.1.11.13	MacAddress	read-only	The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station.
STR configPasswordAdmin	1.3.6.1.4.1.171.10.60.1.11.15	DisplayString	write-only	The adminstrator password
IP configIpAddress	1.3.6.1.4.1.171.10.60.1.11.16	IpAddress	read-write	The IP Address for the RDU box.
IP configNetMask	1.3.6.1.4.1.171.10.60.1.11.17	IpAddress	read-write	The network mask for the RDU box.
IP configGateway	1.3.6.1.4.1.171.10.60.1.11.18	IpAddress	read-write	The Gatway Address for the unit.
INT configSave	1.3.6.1.4.1.171.10.60.1.11.19	INTEGER	read-write	Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing.
INT configRestoreDefaults	1.3.6.1.4.1.171.10.60.1.11.22	INTEGER	read-write	Restores the configuration of the unit to the original settings.
companyTVlanGroup	1.3.6.1.4.1.171.10.60.1.13
tvlanTable	1.3.6.1.4.1.171.10.60.1.13.1		not-accessible	A list of the VLANs
tvlanEntry	1.3.6.1.4.1.171.10.60.1.13.1.1		not-accessible	A VLAN entry containing the VLAN id and name.
INT tvlanId	1.3.6.1.4.1.171.10.60.1.13.1.1.1	INTEGER	read-only	The VLAN identifier. A maximum of 64 VLANs is supported. The value must be from 1 to 4094.
POR tvlanMember	1.3.6.1.4.1.171.10.60.1.13.1.1.3	PortList	read-write	The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
POR tvlanUntaggedPorts	1.3.6.1.4.1.171.10.60.1.13.1.1.4	PortList	read-write	If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged.
INT tvlanStatus	1.3.6.1.4.1.171.10.60.1.13.1.1.5	INTEGER	read-write	The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
tvlanPortTable	1.3.6.1.4.1.171.10.60.1.13.2		not-accessible	A list of ports and their associated VLAN.
tvlanPortEntry	1.3.6.1.4.1.171.10.60.1.13.2.1		not-accessible	Information pertaining to an individual port regarding to which VLAN it belongs.
INT tvlanPortPortId	1.3.6.1.4.1.171.10.60.1.13.2.1.1	INTEGER	read-only	A port identifier that is in the range of 1 to ifNumber.
INT tvlanPortVlanId	1.3.6.1.4.1.171.10.60.1.13.2.1.2	INTEGER	read-write	The default VLAN identifier.
companyPortTrunkGroup	1.3.6.1.4.1.171.10.60.1.14
portTrunkTable	1.3.6.1.4.1.171.10.60.1.14.1		not-accessible	A list of port trunks and their associated members.
portTrunkEntry	1.3.6.1.4.1.171.10.60.1.14.1.1		not-accessible	A port trunk entry containing the trunk id and trunk members.
INT portTrunkId	1.3.6.1.4.1.171.10.60.1.14.1.1.1	INTEGER	read-only	The port trunk identifier. The current range is from 1 to 4.
POR portTrunkMember	1.3.6.1.4.1.171.10.60.1.14.1.1.2	PortList	read-only	Trunk group 1 - 3 has eight members (Port 01/09/17 - 08/16/24). Trunk group 4 has two members (Port 25-26). Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
POR portTrunkMemberValue	1.3.6.1.4.1.171.10.60.1.14.1.1.3	PortList	read-write	A port trunk member value indicates which port is a member of the specified trunk. Valid values are in the range from 0 to ifNumber. A zero indicates that no port is contained in the specifed member. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
INT portTrunkEnable	1.3.6.1.4.1.171.10.60.1.14.1.1.4	INTEGER	read-write	Enable/Disable Trunk group. A (1) enables, a (2) disables.

RFC description

D-Link DES-1526 switch MIB covering community configuration, host management, spanning tree, and miscellaneous switch controls.

Start monitoring D-Link DES-1526 smart switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES-1526-MIB

What Is DES-1526-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description