All MIBs › DES-1252-MIB
Category: VLAN and Bridging, Vendor: D-Link
Description: Manages D-Link DES-1252 48-port smart switch VLAN, QoS, and port configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DES-1252-MIB?
DES-1252-MIB is D-Link's device-specific MIB for the DES-1252, a 48-port smart switch, covering VLAN, QoS, and port configuration management consistent with D-Link's smart switch product line. It exposes Layer 2 configuration objects for VLAN assignment, traffic prioritization, and per-port settings across its higher port-density chassis. For monitoring hardware/software status, its relevant use is tracking per-port operational and link state across a large number of ports, since a 48-port switch multiplies the chance of an individual port or link fault, alongside confirming QoS and VLAN configuration hasn't drifted from policy. It is a vendor-specific enterprise MIB without a notable dependency beyond standard Bridge/VLAN conventions. It is typically deployed in wiring closets or small data rooms where a single high-density D-Link smart switch is monitored and configured via SNMP. Engineers can download the DES-1252-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DES-1252-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link DES-1252 48-port smart switch
Monitoring Examples
No sample objects were available for this module, but consistent with its role, an admin would typically poll per-port link/enable state across all 48 ports to identify any port that has gone down or been disabled, and check VLAN/QoS table entries to confirm port assignments match the intended network design. Given the higher port count, automated polling here is especially useful for catching a single failed port among many. Exact object and table names should be verified against the MIB source since none were captured in the available metadata.
What Can Be Monitored
- per-port link/enable state
- VLAN port assignment
- QoS priority configuration
- port speed and duplex settings
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress | |
| mib-2 |
From SNMPv2-SMI
| Unsigned32 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| d_link | 1.3.6.1.4.1.171 | |||
| dlink_products | 1.3.6.1.4.1.171.10 | |||
| dlink_DES12XXSeriesProd | 1.3.6.1.4.1.171.10.75 | |||
| des_1252a1 | 1.3.6.1.4.1.171.10.75.4 | |||
| NTF swFiberInsert | 1.3.6.1.4.1.171.10.75.4.0.1 | Fiber insert trap. | ||
| NTF swFiberRemove | 1.3.6.1.4.1.171.10.75.4.0.2 | Fiber remove trap. | ||
| NTF swFiberAbnormalRXError | 1.3.6.1.4.1.171.10.75.4.0.3 | Fiber abnormal rx error trap. | ||
| NTF swFiberAbnormalTXError | 1.3.6.1.4.1.171.10.75.4.0.4 | Fiber abnormal tx error trap. | ||
| NTF swTPAbnormalRXError | 1.3.6.1.4.1.171.10.75.4.0.5 | Twisted Pair abnormal rx error trap. | ||
| NTF swTPAbnormalTXError | 1.3.6.1.4.1.171.10.75.4.0.6 | Twisted Pair abnormal tx error trap. | ||
| companyCommGroup | 1.3.6.1.4.1.171.10.75.4.1 | |||
| commSetTable | 1.3.6.1.4.1.171.10.75.4.1.1 | not-accessible | A list of SNMP Set Community Entries. | |
| commSetEntry | 1.3.6.1.4.1.171.10.75.4.1.1.1 | not-accessible | A list of SNMP Set Community properties. | |
| INT commSetIndex | 1.3.6.1.4.1.171.10.75.4.1.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commSetName | 1.3.6.1.4.1.171.10.75.4.1.1.1.2 | DisplayString | read-write | The name of this SNMP Set Community Entry. |
| ROW commSetStatus | 1.3.6.1.4.1.171.10.75.4.1.1.1.3 | RowStatus | read-write | The RowStatus for the Set Community entry. |
| commGetTable | 1.3.6.1.4.1.171.10.75.4.1.2 | not-accessible | A list of SNMP Get Community Entries. | |
| commGetEntry | 1.3.6.1.4.1.171.10.75.4.1.2.1 | not-accessible | A list of SNMP Get Community properties. | |
| INT commGetIndex | 1.3.6.1.4.1.171.10.75.4.1.2.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commGetName | 1.3.6.1.4.1.171.10.75.4.1.2.1.2 | DisplayString | read-write | The name of this SNMP Get Community Entry. |
| ROW commGetStatus | 1.3.6.1.4.1.171.10.75.4.1.2.1.3 | RowStatus | read-write | The RowStatus for the Get Community entry. |
| commTrapTable | 1.3.6.1.4.1.171.10.75.4.1.3 | not-accessible | A list of SNMP Trap Community Entries. | |
| commTrapEntry | 1.3.6.1.4.1.171.10.75.4.1.3.1 | not-accessible | A list of SNMP Trap Community properties. | |
| INT commTrapIndex | 1.3.6.1.4.1.171.10.75.4.1.3.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. |
| STR commTrapName | 1.3.6.1.4.1.171.10.75.4.1.3.1.2 | DisplayString | read-write | The name of this SNMP Trap Community Entry. |
| IP commTrapIpAddress | 1.3.6.1.4.1.171.10.75.4.1.3.1.3 | IpAddress | read-write | The IP Address of this SNMP Trap Community Entry. |
| INT commTrapSNMPBootup | 1.3.6.1.4.1.171.10.75.4.1.3.1.5 | INTEGER | read-write | Bootup trap |
| INT commTrapSNMPTPLinkUpDown | 1.3.6.1.4.1.171.10.75.4.1.3.1.6 | INTEGER | read-write | Twisted Pair link up / link down trap. |
| INT commTrapSNMPFiberLinkUpDown | 1.3.6.1.4.1.171.10.75.4.1.3.1.7 | INTEGER | read-write | Fiber link up / link down trap. |
| INT commTrapTrapAbnormalTPRXError | 1.3.6.1.4.1.171.10.75.4.1.3.1.9 | INTEGER | read-write | Twisted Pair abnormal receive error trap. |
| INT commTrapTrapAbnormalTPTXError | 1.3.6.1.4.1.171.10.75.4.1.3.1.10 | INTEGER | read-write | Twisted Pair abnormal transmit error trap. |
| INT commTrapTrapAbnormalFiberRXError | 1.3.6.1.4.1.171.10.75.4.1.3.1.11 | INTEGER | read-write | Fiber abnormal receive error trap. |
| INT commTrapTrapAbnormalFiberTXError | 1.3.6.1.4.1.171.10.75.4.1.3.1.12 | INTEGER | read-write | Fiber abnormal transmit error trap. |
| ROW commTrapStatus | 1.3.6.1.4.1.171.10.75.4.1.3.1.13 | RowStatus | read-write | The RowStatus for the Trap Community entry. |
| companyMiscGroup | 1.3.6.1.4.1.171.10.75.4.3 | |||
| INT miscReset | 1.3.6.1.4.1.171.10.75.4.3.2 | INTEGER | read-write | Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. |
| INT miscStatisticsReset | 1.3.6.1.4.1.171.10.75.4.3.3 | INTEGER | read-write | Resets the units statistics. A (1) resets the unit, a (2) does nothing. |
| companySpanGroup | 1.3.6.1.4.1.171.10.75.4.4 | |||
| INT spanOnOff | 1.3.6.1.4.1.171.10.75.4.4.1 | INTEGER | read-write | Enable/Disable Spanning Tree. A (1) enables, a (2) disables. |
| companyConfigGroup | 1.3.6.1.4.1.171.10.75.4.11 | |||
| STR configVerSwPrimary | 1.3.6.1.4.1.171.10.75.4.11.1 | DisplayString | read-only | The software image version string. |
| STR configVerHwChipSet | 1.3.6.1.4.1.171.10.75.4.11.2 | DisplayString | read-only | The hardware chipset version string. |
| INT configBootTftpOperation | 1.3.6.1.4.1.171.10.75.4.11.3 | INTEGER | read-write | The tftp operation to perform downloading the boot image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName. |
| IP configBootTftpServerIp | 1.3.6.1.4.1.171.10.75.4.11.4 | IpAddress | read-write | The TFTP server's IP address used for downloading the boot image. |
| STR configBootImageFileName | 1.3.6.1.4.1.171.10.75.4.11.5 | DisplayString | read-write | The filename of the boot image to download. |
| configPortTable | 1.3.6.1.4.1.171.10.75.4.11.6 | not-accessible | A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces. | |
| configPortEntry | 1.3.6.1.4.1.171.10.75.4.11.6.1 | not-accessible | An enterprise specific interface entry. | |
| INT configPort | 1.3.6.1.4.1.171.10.75.4.11.6.1.1 | INTEGER | read-only | A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber. |
| INT configPortSpeed | 1.3.6.1.4.1.171.10.75.4.11.6.1.2 | INTEGER | read-write | The port's speed desired state. |
| INT configPortOperStatus | 1.3.6.1.4.1.171.10.75.4.11.6.1.3 | INTEGER | read-only | The port's operating speed state. |
| INT configPortPriority | 1.3.6.1.4.1.171.10.75.4.11.6.1.6 | INTEGER | read-write | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 4 different priority queues. |
| INT configVLANMode | 1.3.6.1.4.1.171.10.75.4.11.7 | INTEGER | read-write | Determines the VLAN mode. |
| configMirrorTable | 1.3.6.1.4.1.171.10.75.4.11.8 | not-accessible | A list of the Mirror | |
| configMirrorEntry | 1.3.6.1.4.1.171.10.75.4.11.8.1 | not-accessible | A Mirror entry containing the Mirror id and mode. | |
| INT configMirrorId | 1.3.6.1.4.1.171.10.75.4.11.8.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported. |
| INT configMirrorMon | 1.3.6.1.4.1.171.10.75.4.11.8.1.2 | INTEGER | read-write | When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled. |
| POR configMirrorTXSrc | 1.3.6.1.4.1.171.10.75.4.11.8.1.3 | PortList | read-write | When mirroring is enabled , this identifies the TX mirroring source port.This value has a valid range of 1 to ifNumber when enbaled.Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc.Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| POR configMirrorRXSrc | 1.3.6.1.4.1.171.10.75.4.11.8.1.4 | PortList | read-write | When mirroring is enabled , this identifies the RX mirroring source port.This value has a valid range of 1 to ifNumber when enbaled.Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc.Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| ROW configMirrorStatus | 1.3.6.1.4.1.171.10.75.4.11.8.1.5 | RowStatus | read-write | The RowStatus for the Mirror entry. |
| INT configSNMPEnable | 1.3.6.1.4.1.171.10.75.4.11.9 | INTEGER | read-write | Enable/Disable SNMP function. A (1) enables, a (2) disables. |
| INT configIpAssignmentMode | 1.3.6.1.4.1.171.10.75.4.11.12 | INTEGER | read-write | Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP). |
| MAC configPhysAddress | 1.3.6.1.4.1.171.10.75.4.11.13 | MacAddress | read-only | The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station. |
| STR configPasswordAdmin | 1.3.6.1.4.1.171.10.75.4.11.15 | DisplayString | write-only | The adminstrator password |
| IP configIpAddress | 1.3.6.1.4.1.171.10.75.4.11.16 | IpAddress | read-write | The IP Address for the RDU box. |
| IP configNetMask | 1.3.6.1.4.1.171.10.75.4.11.17 | IpAddress | read-write | The network mask for the RDU box. |
| IP configGateway | 1.3.6.1.4.1.171.10.75.4.11.18 | IpAddress | read-write | The Gatway Address for the unit. |
| INT configSave | 1.3.6.1.4.1.171.10.75.4.11.19 | INTEGER | read-write | Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing. |
| INT configRestoreDefaults | 1.3.6.1.4.1.171.10.75.4.11.22 | INTEGER | read-write | Restores the configuration of the unit to the original settings. |
| IP configTftpServerIpAddress | 1.3.6.1.4.1.171.10.75.4.11.32 | IpAddress | read-write | The TFTP server's IP address used to upload or download configuration file. |
| STR configTftpServerFileName | 1.3.6.1.4.1.171.10.75.4.11.33 | DisplayString | read-write | The filename used to store or retrieve the configuration file from the tftp server. |
| INT configTftpOperation | 1.3.6.1.4.1.171.10.75.4.11.34 | INTEGER | read-write | The tftp operation to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. |
| INT configSafeguardEnable | 1.3.6.1.4.1.171.10.75.4.11.44 | INTEGER | read-write | Enable/Disable Safeguard Engine. D-Link Safeguard Engine is a robust and innovative technology developed by D-Link, which will automatically throttle the impact of packet flooding into the switch's CPU. It will keep D-Link Switches better protected from being too frequently interrupted by malicious viruses or worm attacks. |
| companyTVlanGroup | 1.3.6.1.4.1.171.10.75.4.13 | |||
| tvlanTable | 1.3.6.1.4.1.171.10.75.4.13.1 | not-accessible | A list of the VLANs | |
| tvlanEntry | 1.3.6.1.4.1.171.10.75.4.13.1.1 | not-accessible | A VLAN entry containing the VLAN id and name. | |
| INT tvlanId | 1.3.6.1.4.1.171.10.75.4.13.1.1.1 | INTEGER | read-only | The VLAN identifier. A maximum of 256 VLANs is supported. The value must be from 1 to 4094. |
| STR tvlanName | 1.3.6.1.4.1.171.10.75.4.13.1.1.2 | DisplayString | read-write | The VLAN name.Length must between 1 and 20. |
| POR tvlanMember | 1.3.6.1.4.1.171.10.75.4.13.1.1.3 | PortList | read-write | The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| POR tvlanUntaggedPorts | 1.3.6.1.4.1.171.10.75.4.13.1.1.4 | PortList | read-write | If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged. |
| INT tvlanStatus | 1.3.6.1.4.1.171.10.75.4.13.1.1.5 | INTEGER | read-write | The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| INT tvlanManagementOnOff | 1.3.6.1.4.1.171.10.75.4.13.2 | INTEGER | read-write | Enable/Disable management VLAN mechanism. |
| INT tvlanManagementid | 1.3.6.1.4.1.171.10.75.4.13.3 | INTEGER | read-write | The management VLAN ID which allow to forward to CPU. |
| tvlanPortTable | 1.3.6.1.4.1.171.10.75.4.13.4 | not-accessible | A list of ports and their associated VLAN. | |
| tvlanPortEntry | 1.3.6.1.4.1.171.10.75.4.13.4.1 | not-accessible | Information pertaining to an individual port regarding to which VLAN it belongs. | |
| INT tvlanPortPortId | 1.3.6.1.4.1.171.10.75.4.13.4.1.1 | INTEGER | read-only | A port identifier that is in the range of 1 to ifNumber. |
| INT tvlanPortVlanId | 1.3.6.1.4.1.171.10.75.4.13.4.1.2 | INTEGER | read-write | The default VLAN identifier, PVID. The value must be from 1 to 4094. |
| INT tvlanAsyOnOff | 1.3.6.1.4.1.171.10.75.4.13.5 | INTEGER | read-write | Enable/Disable IEEE 802.1Q Asymmetric VLAN |
| companyPortTrunkGroup | 1.3.6.1.4.1.171.10.75.4.14 | |||
| portTrunkTable | 1.3.6.1.4.1.171.10.75.4.14.1 | not-accessible | A list of port trunks and their associated members. | |
| portTrunkEntry | 1.3.6.1.4.1.171.10.75.4.14.1.1 | not-accessible | A port trunk entry containing the trunk id and trunk members. | |
| INT portTrunkId | 1.3.6.1.4.1.171.10.75.4.14.1.1.1 | INTEGER | read-only | The port trunk identifier. The current range is from 1 to 6. |
| STR portTrunkName | 1.3.6.1.4.1.171.10.75.4.14.1.1.2 | DisplayString | read-write | The Trunk name.Length must between 1 and 20. |
| POR portTrunkMember | 1.3.6.1.4.1.171.10.75.4.14.1.1.3 | PortList | read-write | A port trunk member value indicates which port is a member of the specified trunk. Valid values are in the range from 0 to ifNumber. A zero indicates that no port is contained in the specifed member. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. |
| companyStaticGroup | 1.3.6.1.4.1.171.10.75.4.21 | |||
| INT staticOnOff | 1.3.6.1.4.1.171.10.75.4.21.1 | INTEGER | read-write | Enable/Disable Static MAC. Currently it doesn't support 'disabled' function. |
| POR staticAutoLearning | 1.3.6.1.4.1.171.10.75.4.21.2 | PortList | read-write | The set of the device's member ports that belong to the Static MAC auto learning enable/disable. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is in auto learning enable state; the port is not in auto learning state if its bit has a value of '0'. |
| staticTable | 1.3.6.1.4.1.171.10.75.4.21.3 | not-accessible | A list of the Static MACs | |
| staticEntry | 1.3.6.1.4.1.171.10.75.4.21.3.1 | not-accessible | A Static MAC entry containing the mac and forwarding port. | |
| INT staticId | 1.3.6.1.4.1.171.10.75.4.21.3.1.1 | INTEGER | read-only | The Static MAC identifier. A maximum of 60 Static MACs is supported. The value must be from 1 to 60 |
| MAC staticMac | 1.3.6.1.4.1.171.10.75.4.21.3.1.2 | MacAddress | read-write | The Static MAC associated with the Id. |
| INT staticPort | 1.3.6.1.4.1.171.10.75.4.21.3.1.3 | INTEGER | read-write | The Static MAC forwarding port with the ID. |
| INT staticVlanID | 1.3.6.1.4.1.171.10.75.4.21.3.1.4 | INTEGER | read-write | The Static MAC VLAN ID with the ID. |
| INT staticStatus | 1.3.6.1.4.1.171.10.75.4.21.3.1.5 | INTEGER | read-write | The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
| companyIgsGroup | 1.3.6.1.4.1.171.10.75.4.22 | |||
| igsSystem | 1.3.6.1.4.1.171.10.75.4.22.1 | |||
| INT igsStatus | 1.3.6.1.4.1.171.10.75.4.22.1.2 | INTEGER | read-write | Enables or disables IGMP snooping in the system. |
| INT igsv3Processing | 1.3.6.1.4.1.171.10.75.4.22.1.3 | INTEGER | read-only | To enable processing of IGMPv3 messages and to operate in IGMPv3 mode, this object must be set to enabled, when set as disabled the operation will be in IGMPv2 mode. |
| INT igsRouterPortPurgeInterval | 1.3.6.1.4.1.171.10.75.4.22.1.4 | INTEGER | read-write | This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, a 'RouterPortPurgeTimer' runs for 'RouterPortPurgeInterval'. This timer will be restarted whenever a router control message is received over that port. If no router control mssages are received for 'RouterPortPurgeInterval' time, the learnt router port entry will be purged. |
| INT igsHostPortPurgeInterval | 1.3.6.1.4.1.171.10.75.4.22.1.5 | INTEGER | read-only | This is the interval (in seconds) after which a learnt host port entry will be purged. For each host port learnt, a 'PortPurgeTimer' runs for 'HostPortPurgeInterval'. This timer will be restarted whenever a report message from host is received over that port. If no report mssages are received for 'HostPortPurgeInterval' time, the learnt host entry will be purged from the multicast group. |
| INT igsReportForwardInterval | 1.3.6.1.4.1.171.10.75.4.22.1.6 | INTEGER | read-only | This is the interval (in seconds) within which the next report messages for the same multicast group will not be forwarded out. The purpose of this timer is to avoid multiple report messages for the same group being forwarded out. So that unnecessary multicast packets in the network can be avoided. The 'ReportForwardTimer' is per multicast group. This timer is started as soon as a report message for that group is forwarded out. Within this 'ReportForwardInterval' if another report for the same group arrives, that report will not be forwarded. The first report message which is received for this group after the 'ReportForwardInterval' only will be forwarded out. When set as '0' , this timer will not be started and all the report messages will be forwarded as and when they are received. |
| INT igsLeaveProcessInterval | 1.3.6.1.4.1.171.10.75.4.22.1.7 | INTEGER | read-write | This is the interval (in seconds) after which a Leave message is forwarded on either router port(if present) or on all ports of a bridge (if no router port present). when a leave message from a host for a group is received by the bridge, The bridge will form a group-specific query and sends it on the port on which the leave message is received. A timer is started by a bridge with a time interval equal to IgsLeaveProcessInterval. If a report message is received before above timer expires, Leave message is dropped.Otherwise Leave message is either forwarded on all ports of the bridge or only on router port depending upon the case. |
| INT igsMcastEntryAgeingInterval | 1.3.6.1.4.1.171.10.75.4.22.1.8 | INTEGER | read-only | This is the interval (in seconds) after which the target will be checked for Multicast data hit for the entry This timer will be started for every (S, G) in the control plane. |
| INT igsSharedSegmentAggregationInterval | 1.3.6.1.4.1.171.10.75.4.22.1.9 | INTEGER | read-only | This is the interval (in seconds) for which reports of IGMPv3 messages on a shared segment will be aggregated for a group. This timer will be started only when multiple hosts are identified on a port for the Multicast group. The timer will be stopped when all but one host is left on the port for the Multicast group. This timer will be re-started on its expiry and Multicast forwarding table will be updated. |
| INT igsGblReportFwdOnAllPorts | 1.3.6.1.4.1.171.10.75.4.22.1.10 | INTEGER | read-only | IGMP snooping module will forward reports only on router ports by default, to enable forwarding on all other ports the object must be set to allports. |
| INT igsNextMcastFwdMode | 1.3.6.1.4.1.171.10.75.4.22.1.13 | INTEGER | read-only | This field describes the multicast forwarding mode that will be used upon restart of the ISS Switch. |
| INT igsQueryInterval | 1.3.6.1.4.1.171.10.75.4.22.1.14 | INTEGER | read-write | The frequency at which IGMP Host-Query packets are transmitted on this interface. |
| INT igsQueryMaxResponseTime | 1.3.6.1.4.1.171.10.75.4.22.1.15 | INTEGER | read-write | The maximum query response time advertised in IGMPv2 queries on this interface. |
| INT igsRobustnessValue | 1.3.6.1.4.1.171.10.75.4.22.1.16 | INTEGER | read-write | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses. |
| INT igsLastMembQueryInterval | 1.3.6.1.4.1.171.10.75.4.22.1.17 | INTEGER | read-write | The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group. The value of this object is irrelevant if igmpInterfaceVersion is 1. |
| INT igsQuerierStateOnOff | 1.3.6.1.4.1.171.10.75.4.22.1.18 | INTEGER | read-write | To enable transmitting IGMP Query packets or to disable. |
| igsVlan | 1.3.6.1.4.1.171.10.75.4.22.3 | |||
| igsVlanMcastFwdTable | 1.3.6.1.4.1.171.10.75.4.22.3.1 | not-accessible | This table contains VLAN based multicast forwarding information learnt when VLAN is ENABLED in the system. | |
| igsVlanMcastFwdEntry | 1.3.6.1.4.1.171.10.75.4.22.3.1.1 | not-accessible | This table contains VlanId, multicast group address and the list of ports who have members for the multicast group. | |
| INT igsVlanMcastFwdVlanIdMac | 1.3.6.1.4.1.171.10.75.4.22.3.1.1.1 | INTEGER | not-accessible | Vlan Id pertaining to the Multicast forwarding entry. |
| MAC igsVlanMcastFwdGroupAddress | 1.3.6.1.4.1.171.10.75.4.22.3.1.1.2 | MacAddress | not-accessible | MAC multicast group address. |
| POR igsVlanMcastFwdPortListMac | 1.3.6.1.4.1.171.10.75.4.22.3.1.1.3 | PortList | read-only | List of ports who have members for the MAC multicast group and the Vlan Id. |
| igsVlanRouterPortListTable | 1.3.6.1.4.1.171.10.75.4.22.3.3 | not-accessible | This table contains list of bridge ports through which a router, in a particular VLAN, is reachable. | |
| igsVlanRouterPortListEntry | 1.3.6.1.4.1.171.10.75.4.22.3.3.1 | not-accessible | Contains VlanId of router , list of reachable router ports. | |
| INT igsVlanRouterPortListVlanId | 1.3.6.1.4.1.171.10.75.4.22.3.3.1.1 | INTEGER | not-accessible | Vlan Id of the ports through which router is reachable. |
| POR igsVlanRouterPortList | 1.3.6.1.4.1.171.10.75.4.22.3.3.1.2 | PortList | read-only | Contains list of bridge ports through which a router, in a particular VLAN, is reachable. These router ports are learnt through control messages received from routers, and can also be configured statically. |
| igsVlanFilterTable | 1.3.6.1.4.1.171.10.75.4.22.3.4 | not-accessible | This table contains configuration to disable IGMP snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. | |
| igsVlanFilterEntry | 1.3.6.1.4.1.171.10.75.4.22.3.4.1 | not-accessible | Contains Vlan Id , Vlan Filter Status. | |
| INT igsVlanId | 1.3.6.1.4.1.171.10.75.4.22.3.4.1.1 | INTEGER | not-accessible | Vlan Id for which IGMP snooping feature is to be disabled. |
| INT igsVlanFilterStatus | 1.3.6.1.4.1.171.10.75.4.22.3.4.1.2 | INTEGER | read-write | When status is set as enabled, IGMP snooping feature is disabled for that Vlan Id. When status is set as disabled, the entry stands invalid. In that case IGMP snooping feature remains enabled for that Vlan. |
| companyDot1xGroup | 1.3.6.1.4.1.171.10.75.4.23 | |||
| radius | 1.3.6.1.4.1.171.10.75.4.23.1 | |||
| IP radiusServerAddress | 1.3.6.1.4.1.171.10.75.4.23.1.1 | IpAddress | read-write | The IP address of the RADIUS server. |
| INT radiusServerPort | 1.3.6.1.4.1.171.10.75.4.23.1.2 | INTEGER | read-write | The Port of the RADIUS server. |
| STR radiusServerSharedSecret | 1.3.6.1.4.1.171.10.75.4.23.1.3 | DisplayString | read-write | The secret string which is shared between Server and Client. |
| dot1xAuth | 1.3.6.1.4.1.171.10.75.4.23.2 | |||
| INT dot1xAuthSystemControl | 1.3.6.1.4.1.171.10.75.4.23.2.1 | INTEGER | read-write | Enable/Disable Static 802.1x. A (1) enables, a (2) disables. |
| INT dot1xAuthQuietPeriod | 1.3.6.1.4.1.171.10.75.4.23.2.2 | INTEGER | read-write | The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine. |
| INT dot1xAuthTxPeriod | 1.3.6.1.4.1.171.10.75.4.23.2.3 | INTEGER | read-write | The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine. |
| INT dot1xAuthSuppTimeout | 1.3.6.1.4.1.171.10.75.4.23.2.4 | INTEGER | read-write | The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine. |
| INT dot1xAuthServerTimeout | 1.3.6.1.4.1.171.10.75.4.23.2.5 | INTEGER | read-write | The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine. |
| INT dot1xAuthMaxReq | 1.3.6.1.4.1.171.10.75.4.23.2.6 | INTEGER | read-write | The value of the maxReq constant currently in use by the Backend Authentication state machine. |
| U32 dot1xAuthReAuthPeriod | 1.3.6.1.4.1.171.10.75.4.23.2.7 | Unsigned32 | read-write | The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine. |
| INT dot1xAuthReAuthEnabled | 1.3.6.1.4.1.171.10.75.4.23.2.8 | INTEGER | read-write | The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). |
| dot1xAuthConfigPortTable | 1.3.6.1.4.1.171.10.75.4.23.2.9 | not-accessible | A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself. | |
| dot1xAuthConfigPortEntry | 1.3.6.1.4.1.171.10.75.4.23.2.9.1 | not-accessible | The configuration information for an Authenticator Port. | |
| INT dot1xAuthConfigPortNumber | 1.3.6.1.4.1.171.10.75.4.23.2.9.1.1 | INTEGER | read-only | A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber. |
| INT dot1xAuthConfigPortControl | 1.3.6.1.4.1.171.10.75.4.23.2.9.1.2 | INTEGER | read-write | The current value of the controlled Port control parameter for the Port. |
| INT dot1xAuthConfigPortStatus | 1.3.6.1.4.1.171.10.75.4.23.2.9.1.3 | INTEGER | read-only | The current value of the controlled Port status parameter for the Port. |
| TIK dot1xAuthConfigPortSessionTime | 1.3.6.1.4.1.171.10.75.4.23.2.9.1.4 | TimeTicks | read-only | The duration of the session in seconds. |
| STR dot1xAuthConfigPortSessionUserName | 1.3.6.1.4.1.171.10.75.4.23.2.9.1.5 | DisplayString | read-only | The User-Name representing the identity of the Supplicant PAE. |
| companyQoSGroup | 1.3.6.1.4.1.171.10.75.4.26 | |||
| INT qosMode | 1.3.6.1.4.1.171.10.75.4.26.1 | INTEGER | read-write | Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS. |
| INT queuingMechanism | 1.3.6.1.4.1.171.10.75.4.26.2 | INTEGER | read-write | Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin |
| dot1pPortTable | 1.3.6.1.4.1.171.10.75.4.26.3 | not-accessible | A list of 802.1p port default priority Entries. | |
| dot1pPortEntry | 1.3.6.1.4.1.171.10.75.4.26.3.1 | not-accessible | A list of 802.1p port default priority priorities. | |
| INT dot1pPortIndex | 1.3.6.1.4.1.171.10.75.4.26.3.1.1 | INTEGER | read-only | A port identifier that is in the range of 1 to ifNumber. |
| INT dot1pPortPriority | 1.3.6.1.4.1.171.10.75.4.26.3.1.2 | INTEGER | read-write | For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 4 different priority queues. |
| dscpTable | 1.3.6.1.4.1.171.10.75.4.26.4 | not-accessible | A list of DSCP Entries. | |
| dscpEntry | 1.3.6.1.4.1.171.10.75.4.26.4.1 | not-accessible | A list of DSCP properties. | |
| INT dscpIndex | 1.3.6.1.4.1.171.10.75.4.26.4.1.1 | INTEGER | read-only | DSCP value. For ingress IP packets, the DiffServ field of IP packets provide DSCP-based traffic prioritization information to switches. D-Link Smart Switches will refer to the value of DiffServ filed information and prioritize them with 4 different priority queues. |
| INT dscpPriority | 1.3.6.1.4.1.171.10.75.4.26.4.1.2 | INTEGER | read-write | The queuing priority mapping to DSCP value. |
| companyTrafficMgmt | 1.3.6.1.4.1.171.10.75.4.27 | |||
| broadcastStormCtrlSettings | 1.3.6.1.4.1.171.10.75.4.27.3 | |||
| INT broadcastStormCtrlGlobalOnOff | 1.3.6.1.4.1.171.10.75.4.27.3.1 | INTEGER | read-write | This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device. |
| INT broadcastStormGlobalThreshold | 1.3.6.1.4.1.171.10.75.4.27.3.2 | INTEGER | read-write | The threshold value in unit of thousand bytes per second for broadcast traffic of the specific port. |
| companySecurity | 1.3.6.1.4.1.171.10.75.4.28 | |||
| trustedHostSettings | 1.3.6.1.4.1.171.10.75.4.28.1 | |||
| INT trustedHostOnOff | 1.3.6.1.4.1.171.10.75.4.28.1.1 | INTEGER | read-write | This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. |
| trustedHostTable | 1.3.6.1.4.1.171.10.75.4.28.1.2 | not-accessible | A list of Trusted Host Entries. | |
| trustedHostEntry | 1.3.6.1.4.1.171.10.75.4.28.1.2.1 | not-accessible | A list of Trusted Host properties. | |
| INT trustedHostID | 1.3.6.1.4.1.171.10.75.4.28.1.2.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the Trusted Host Table. Three entries are currently supported. |
| IP trustedHostIpAddress | 1.3.6.1.4.1.171.10.75.4.28.1.2.1.2 | IpAddress | read-write | The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. |
| IP trustedHostIpMask | 1.3.6.1.4.1.171.10.75.4.28.1.2.1.3 | IpAddress | read-write | Used to mask with IP address, it allow you set a subnet as a trusted host entry. |
| INT trustedHostStatus | 1.3.6.1.4.1.171.10.75.4.28.1.2.1.4 | INTEGER | read-write | The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. |
RFC description
D-Link DES-1252 managed switch MIB for VLAN, QoS, and Spanning Tree management.
Start monitoring D-Link DES-1252 48-port smart switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.