CTRON-SFPS-CALL-MIB

All MIBs › CTRON-SFPS-CALL-MIB

Category: Vendor: Cabletron/Enterasys

Description: Manages Cabletron SFPS virtual circuit call setup, teardown, and active call statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-SFPS-CALL-MIB?

CTRON-SFPS-CALL-MIB is a Cabletron (Enterasys) enterprise MIB that manages virtual-circuit call signaling on the SecureFast Packet Switch (SFPS), tracking SAP (service access point) call setup, teardown, and active call state between switch control points. It exposes a SAP table describing each call's tag/hash identifiers, its source and destination control-point (CP), the SAP value, and administrative/operational status for that call instance. For software status monitoring, sfpsSapTableOperStatus/sfpsSapTableAdminStatus show whether a given virtual-circuit call is actually connected versus configured-but-down, and sfpsSapTableStateTime shows how long the call has held that state, helping identify calls stuck in a transitional or failed state. It works together with CTRON-SFPS-BASE-MIB and CTRON-SFPS-CONN-MIB, since call setup here maps onto the connection and resource tables defined in those companion MIBs. It is deployed on Cabletron SecureFast Packet Switch devices to monitor active virtual-circuit calls within the SFPS virtual-networking fabric. Engineers can download the CTRON-SFPS-CALL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-SFPS-CALL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron SecureFast Packet Switch (SFPS)

Monitoring Examples

An administrator would poll sfpsSapTable entries and compare sfpsSapTableAdminStatus to sfpsSapTableOperStatus for a given sfpsSapTableSourceCP/sfpsSapTableDestCP pair to confirm the call between those two control points is actually up. A call showing admin status enabled but operational status down for an extended sfpsSapTableStateTime would flag a stuck or failed call setup needing attention. The sfpsSapTableTag and sfpsSapTableHash/sfpsSapTableHashIndex fields let the admin correlate a specific call instance back to the originating service request.

What Can Be Monitored

virtual-circuit call admin/operational status
call source/destination control point
call state duration
active SAP/call table entries

Imported Objects

From CTRON-SFPS-INCLUDE-MIB

sfpsCallByTuple	OBJECT-IDENTITY
sfpsCallTableStats	OBJECT-IDENTITY
sfpsSap	OBJECT-IDENTITY
sfpsSapAPI	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
sfpsSapTable	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1		not-accessible	This table contains the registered (active) call processors indexed (indirectly) by address and address type supported.
sfpsSapTableEntry	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1		not-accessible	Each entry contains information pertaining to an active call processor.
INT sfpsSapTableTag	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.1	INTEGER	read-only	A type tag used to sort and index the table entries.
INT sfpsSapTableHash	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.2	INTEGER	read-only	A hash of the sfpsSapTableAddress used to identify the instance.
INT sfpsSapTableHashIndex	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.3	INTEGER	read-only	A count of the non-unique sfpsSapTableAddress hashes used to identify the instance.
STR sfpsSapTableSourceCP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.4	DisplayString	read-only	The name of the call processor initiating the the SAP attempts for this particular SAP load.
STR sfpsSapTableDestCP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.5	DisplayString	read-only	The destination call processor that is registered for with this source call processor for the given SAP load.
STR sfpsSapTableSAP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.6	DisplayString	read-only	The value of the SAP in 0x format.
INT sfpsSapTableOperStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.7	INTEGER	read-only	Displays the Current OperStatus of the SAP entry.
INT sfpsSapTableAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.8	INTEGER	read-only	Displays the Current AdminStatus of the SAP entry.
TIK sfpsSapTableStateTime	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.9	TimeTicks	read-only	Total number of SFPSElements stored in NVRAM for persistence.
STR sfpsSapTableDescription	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.10	DisplayString	read-only	Text description of the entry.
INT sfpsSapTableNumAccepted	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.11	INTEGER	read-only	Number accepted by the SAP.
INT sfpsSapTableNumDropped	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.12	INTEGER	read-only	Number dropped by the SAP.
INT sfpsSapTableUnicastSap	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.13	INTEGER	read-write
INT sfpsSapTableNVStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.1.1.14	INTEGER	read-only	Status in NVRAM for persistence.
INT sfpsSapAPIVerb	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.1	INTEGER	read-write	1 - getStatus -- The default verb. When the SourceCP, DestCP, and SAP info are entered, this action will get the current AdminStatus, OperStatus, and NvramStatus. (Must perform a mo_get after setting the above info to actually get the status info) 2 - next -- Move to the next Entry in the SAP Table and Get the status. If this operation is successful, the verb will stay next, else it defaults to getStatus. 3 - first -- Jump back to the First Entry in the SAP Table. 4 - disable -- Disable the Current SAP Entry. This does not effect the Status of this Entry in Nvram. 5 - disableInNvram -- Set the Current SAP Entries status to Disabled in Nvram - This does not effect the Current Admin Status for this SAP Entry. 6 - enable -- Enable the Current SAP Entry. This does not effect the Status of this Entry in Nvram. 7 - enableInNvram -- Set the Current SAP Entries status to Enabled in Nvram - This does not effect the Current Admin Status for this SAP Entry. 8 - clearFromNvram -- Clear the Current SAP Entry from Nvram (if set). 9 - clearAllNvram -- Clear all SAP Entries from Nvram. 10 - resetStats -- Resets the Accepted/Dropped Stats for the Current/Entered SAP Entry. 11 - resetAllStats -- Resets the Accepted/Dropped Stats for all SAP Entries.
STR sfpsSapAPISourceCP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.2	DisplayString	read-write	The name of the call processor initiating the the SAP attempts for this particular SAP load.
STR sfpsSapAPIDestCP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.3	DisplayString	read-write	The destination call processor that is registered for with this source call processor for the given SAP load.
STR sfpsSapAPISAP	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.4	DisplayString	read-write	Enter in the SAP for the desired SAP Entry.
INT sfpsSapAPINVStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.5	INTEGER	read-only	Displays the Current Admin Status of this SAP Entry saved in Nvram.
INT sfpsSapAPIAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.6	INTEGER	read-only	Displays the Current AdminStatus of the SAP Entry.
INT sfpsSapAPIOperStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.7	INTEGER	read-only	Displays the Current OperStatus of the SAP Entry.
INT sfpsSapAPINvSet	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.8	INTEGER	read-only	Total number of entries stored in NVRAM for persistence.
INT sfpsSapAPINVTotal	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.9	INTEGER	read-write	Total number of entries allocated in NVRAM. The switch will always allocate enough space in NVRAM for the number of elements. That is, NvTotal will always be greater than or equal to NvSet.
INT sfpsSapAPINumAccept	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.10	INTEGER	read-only
INT sfpsSapAPINvDiscard	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.11	INTEGER	read-only
INT sfpsSapAPIDefaultStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.2.2.12	INTEGER	read-only
sfpsCallByTupleTable	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1		not-accessible	This table contains the call tags, and call states indexed (indirectly) by switch tuple (in port, src address, dst address)
sfpsCallByTupleEntry	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1		not-accessible	Each entry contains information pertaining to a call tag and its state.
INT sfpsCallByTupleInPort	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.1	INTEGER	read-only	Port of the switch on which the packet associated with this call tag was seen.
INT sfpsCallByTupleSrcHash	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.2	INTEGER	read-only	A hash of sfpsCallByTupleBotSrcAddress used to identify the instance.
INT sfpsCallByTupleDstHash	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.3	INTEGER	read-only	A hash of sfpsCallByTupleTopDstAddress used to identify the instance.
INT sfpsCallByTupleHashIndex	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.4	INTEGER	read-only	A count of non-unique sfpsCallByTupleSrcHash and sfpsCallByTupleDstHash pairs used to identify the instance.
STR sfpsCallByTupleBotSrcType	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.5	DisplayString	read-only	The source address type of the lowest known protocol layer.
STR sfpsCallByTupleBotSrcAddress	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.6	DisplayString	read-only	The source address value of the lowest known protocol layer.
STR sfpsCallByTupleBotDstType	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.7	DisplayString	read-only	The destination address type of the lowest known protocol layer.
STR sfpsCallByTupleBotDstAddress	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.8	DisplayString	read-only	The destination address value of the lowest known protocol layer.
STR sfpsCallByTupleTopSrcType	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.9	DisplayString	read-only	The source address type of the highest learned protocol layer.
STR sfpsCallByTupleTopSrcAddress	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.10	DisplayString	read-only	The source address value of the highest learned protocol layer.
STR sfpsCallByTupleTopDstType	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.11	DisplayString	read-only	The destination address type of the highest learned protocol layer.
STR sfpsCallByTupleTopDstAddress	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.12	DisplayString	read-only	The destination address value of the highest learned protocol layer.
STR sfpsCallByTupleCallProcName	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.13	DisplayString	read-only	The name of the call processor responsible for all signaling for this packet/call tag.
NUM sfpsCallByTupleCallTag	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.14	HexInteger	read-only	The number used to reference this packet and its associated calls.
STR sfpsCallByTupleCallState	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.15	DisplayString	read-only	The current state of the packet in the call processor.
TIK sfpsCallByTupleTimeRemaining	1.3.6.1.4.1.52.4.2.4.2.2.5.1.5.1.1.16	TimeTicks	read-only	The number of time ticks remaining before this entry's timer expires and it is removed from the table.
INT sfpsCallTableStatsRam	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.1	INTEGER	read-only	The number of bytes used by the Call Table.
INT sfpsCallTableStatsSize	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.2	INTEGER	read-only	The number of entries in the Call Table.
INT sfpsCallTableStatsInUse	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.3	INTEGER	read-only	The current number of calls in use. A call goes into this table only if it is being blocked (waiting for resolve or sent new user).
INT sfpsCallTableStatsMax	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.4	INTEGER	read-only	The maximum number of calls that the switch maintained.
INT sfpsCallTableStatsTotMisses	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.5	INTEGER	read-only	The number of times that there were no calls available in the Call Table. This would be the number of calls that had to be dropped.
TIK sfpsCallTableStatsMissStart	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.7	TimeTicks	read-only	Time when last miss occurred
TIK sfpsCallTableStatsMissStop	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.8	TimeTicks	read-only	Time when missing stopped
INT sfpsCallTableStatsLastMiss	1.3.6.1.4.1.52.4.2.4.2.2.5.1.6.9	INTEGER	read-write	Number of calls dropped in last miss, also write 0 to files

RFC description

Cabletron Fast Packet Switching (SFPS) call processor and SAP management MIB.

Start monitoring Cabletron SecureFast Packet Switch (SFPS), call signaling with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-SFPS-CALL-MIB

What Is CTRON-SFPS-CALL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description