All MIBs › COM21-HCXRX-MIB
Organization: Com21, Inc.
Last Updated: 1997-01-08
Category: DOCSIS and Cable
Description: Monitors downstream receive channel parameters for COM21 HCX cable modem equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is COM21-HCXRX-MIB?
This is a private-enterprise MIB from COM21 for the ComController RX (downstream receive) card used in their HCX-series hybrid fiber-coax (HFC) cable broadband access equipment. It exposes card-level configuration and status data for the downstream receive path, such as channel frequency, modulation, and signal-level parameters on the headend RX card. Because it targets a specific receive card, it is primarily used to monitor the hardware health of that card - whether it is present and operating normally, and the quality of the incoming downstream RF signal it is receiving - functioning as a hardware/signal-status indicator for the ComController chassis. It is one part of a larger family of COM21 ComController MIBs (unit-control, topology, VLAN, etc.) and likely relies on those companion modules and standard interface conventions for full-unit context. It would typically be deployed by a cable operator's network operations center to monitor headend equipment in an HFC access network. Engineers can download the COM21-HCXRX-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in COM21-HCXRX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- COM21 ComController headend unit
- cable/HFC broadband access equipment
Monitoring Examples
The sample_objects list supplied for this MIB was empty, so no exact object or table names can be cited here. In practice this module would expose per-card receive-channel objects (frequency, signal level, lock/status) on the ComController RX card, which an operator would poll to detect a degraded or lost downstream signal on a given card slot. This should be treated as a general characterization based on the module description rather than a citation of confirmed OIDs.
What Can Be Monitored
- RX card operational status
- downstream receive signal level
- channel frequency/modulation settings
This MIB depends on
Related MIBs
Imported Objects
From COM21-HCX-MIB
| com21 | OBJECT-IDENTITY |
| com21Hcx | OBJECT-IDENTITY |
| com21Traps | OBJECT-IDENTITY |
From COM21-HCXALM-MIB
| hcxAlmSeverity | OBJECT-TYPE |
| hcxEventLogTime | OBJECT-TYPE |
From SNMPv2-SMI
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| MacAddress |
How to Use in IPNetwork Monitor
Example using hcxPortCurrMinRxCells OID:
Select a Com21 ComController HCX downstream RX card (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hcxPortCurrMinRxCells into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Represents the number of cells received in the current 15 minute period. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| com21HcxRfAnalysisEntry | 1.3.6.1.4.1.1141.2.37.1.1 | not-accessible | . | |
| com21HcxRfAnalysisGroup | 1.3.6.1.4.1.1141.2.37 | |||
| com21HcxRfAnalysisTable | 1.3.6.1.4.1.1141.2.37.1 | not-accessible | . | |
| com21HcxRpmIPortEntry | 1.3.6.1.4.1.1141.2.35.1.1 | not-accessible | . | |
| com21HcxRpmIPortGroup | 1.3.6.1.4.1.1141.2.35 | |||
| com21HcxRpmIPortTable | 1.3.6.1.4.1.1141.2.35.1 | not-accessible | . | |
| com21HcxRpmStatsEntry | 1.3.6.1.4.1.1141.2.36.1.1 | not-accessible | . | |
| com21HcxRpmStatsGroup | 1.3.6.1.4.1.1141.2.36 | |||
| com21HcxRpmStatsTable | 1.3.6.1.4.1.1141.2.36.1 | not-accessible | . | |
| com21HcxRx | 1.3.6.1.4.1.1141.2.30 | This is the Com21 ComController RX card MIB. COM21 Part# 005-0025-00 | ||
| com21HcxUpstrmPortEntry | 1.3.6.1.4.1.1141.2.31.1.1 | not-accessible | . | |
| com21HcxUpstrmPortGroup | 1.3.6.1.4.1.1141.2.31 | |||
| com21HcxUpstrmPortTable | 1.3.6.1.4.1.1141.2.31.1 | not-accessible | . | |
| com21HcxUpstrmStatsEntry | 1.3.6.1.4.1.1141.2.32.1.1 | not-accessible | . | |
| com21HcxUpstrmStatsGroup | 1.3.6.1.4.1.1141.2.32 | |||
| com21HcxUpstrmStatsTable | 1.3.6.1.4.1.1141.2.32.1 | not-accessible | . | |
| com21HcxUpstrmUnitEntry | 1.3.6.1.4.1.1141.2.33.1.1 | not-accessible | . | |
| com21HcxUpstrmUnitGroup | 1.3.6.1.4.1.1141.2.33 | |||
| com21HcxUpstrmUnitTable | 1.3.6.1.4.1.1141.2.33.1 | not-accessible | . | |
| com21HcxVciStatsEntry | 1.3.6.1.4.1.1141.2.34.1.1 | not-accessible | . | |
| com21HcxVciStatsGroup | 1.3.6.1.4.1.1141.2.34 | |||
| com21HcxVciStatsTable | 1.3.6.1.4.1.1141.2.34.1 | not-accessible | . | |
| INT hcxAcquisitionEnable | 1.3.6.1.4.1.1141.2.33.1.1.10 | INTEGER | read-write | Used to select an RF Receiver for acquisition. The ComController shall ensure that only one RX card in a receiver group is selected for acquisition. |
| NTF hcxCellErrRatioThres | 1.3.6.1.4.1.1141.4.81 | Severity is WARNING. | ||
| NTF hcxCnrThres | 1.3.6.1.4.1.1141.4.83 | Tbd. Severity is WARNING. | ||
| NTF hcxCorrectedFecMinThres | 1.3.6.1.4.1.1141.4.38 | Severity is WARNING. | ||
| NTF hcxCorrFecRatioThres | 1.3.6.1.4.1.1141.4.80 | Severity is WARNING. | ||
| INT hcxPortCellErrRatioThres | 1.3.6.1.4.1.1141.2.32.1.1.20 | INTEGER | read-write | This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of FEC/HEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxPortRatioThresPeriod attribute before a trap is generated. In addition the cells received within one second must be greater than that defined by hcxPortMinErrRatioCells. A value of 0 disables the threshold. Default is 10. If this RX port is connected to an RPM then this threshold is not valid. |
| INT hcxPortClearStats | 1.3.6.1.4.1.1141.2.32.1.1.31 | INTEGER | read-write | This attribute is used to clear all RX statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr. |
| INT hcxPortCnrThres | 1.3.6.1.4.1.1141.2.32.1.1.23 | INTEGER | read-write | Defines the average carrier to noise level, in dB, at which a frequency hop should occur. Note that the data error thresholds define above take precedence - this CNR threshold applies only if the data rate is less than the hcxPortMinErrRatioCells. Default 11dB. If this RX port is connected to an RPM then this threshold is not valid. |
| INT hcxPortCorrFecRatioThres | 1.3.6.1.4.1.1141.2.32.1.1.19 | INTEGER | read-write | This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of corrected FEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxPortRatioThresPeriod attribute before a trap is generated. In addition the cells received within the second must be greater than that defined by hcxPortMinErrRatioCells. A value of 0 disables the threshold. Default is 20. If this RX port is connected to an RPM then this threshold is not valid. |
| I32 hcxPortCurrMaxNoise | 1.3.6.1.4.1.1141.2.32.1.1.25 | Integer32 | read-only | defines the maximum noise level in dBmv sampled by the RX card in the current 15 minute period. |
| I32 hcxPortCurrMeanNoise | 1.3.6.1.4.1.1141.2.32.1.1.17 | Integer32 | read-only | This attribute defines the mean noise level in dBmv sampled by the RX card in the current 15 minute period. |
| G32 hcxPortCurrMinCorrectedFec | 1.3.6.1.4.1.1141.2.32.1.1.8 | Gauge32 | read-only | Represents the number of corrected FEC errors in the current 15 minute period. |
| I32 hcxPortCurrMinNoise | 1.3.6.1.4.1.1141.2.32.1.1.24 | Integer32 | read-only | defines the minimum noise level in dBmv sampled by the RX card in the current 15 minute period. |
| G32 hcxPortCurrMinOverSubPeriods | 1.3.6.1.4.1.1141.2.32.1.1.9 | Gauge32 | read-only | Represents the number of 512 cell slot scheduling periods that were actively oversubscribed in the current 15 minute period. |
| G32 hcxPortCurrMinRxCellsEx | 1.3.6.1.4.1.1141.2.32.1.1.4 | Gauge32 | read-only | Represents the number of cells received in the current 15 minute period. |
| G32 hcxPortCurrMinRxNullCells | 1.3.6.1.4.1.1141.2.32.1.1.5 | Gauge32 | read-only | Represents the number of null cells received in the current 15 minute period. |
| G32 hcxPortCurrMinUncorrFecHecCells | 1.3.6.1.4.1.1141.2.32.1.1.6 | Gauge32 | read-only | Represents the number of received cells with either uncorrectable FEC or HEC errors in current 15 minute period. |
| INT hcxPortMinErrRatioCells | 1.3.6.1.4.1.1141.2.32.1.1.22 | INTEGER | read-write | This attribute defines the minimum number of cells that should be received per second in order to allow the Error and Corrected Cell Thresholds to cause a frequency hop. Default is 50. |
| I32 hcxPortPrevMaxNoise | 1.3.6.1.4.1.1141.2.32.1.1.27 | Integer32 | read-only | defines the maximum noise level in dBmv sampled by the RX card in the previous 15 minute period. |
| I32 hcxPortPrevMeanNoise | 1.3.6.1.4.1.1141.2.32.1.1.18 | Integer32 | read-only | This attribute defines the mean noise level in dBmv sampled by the RX card in the previous 15 minute period. |
| G32 hcxPortPrevMinCorrectedFec | 1.3.6.1.4.1.1141.2.32.1.1.14 | Gauge32 | read-only | Represents the number of corrected FEC errors in the previous 15 minute period. |
| I32 hcxPortPrevMinNoise | 1.3.6.1.4.1.1141.2.32.1.1.26 | Integer32 | read-only | defines the minimum noise level in dBmv sampled by the RX card in the previous 15 minute period. |
| G32 hcxPortPrevMinOverSubPeriods | 1.3.6.1.4.1.1141.2.32.1.1.15 | Gauge32 | read-only | Represents the number of 512 cell slot scheduling periods that were actively oversubscribed in the previous 15 minute period. |
| G32 hcxPortPrevMinRxCells | 1.3.6.1.4.1.1141.2.32.1.1.10 | Gauge32 | read-only | Represents the number of cells received in the previous 15 minute period. |
| G32 hcxPortPrevMinRxNullCells | 1.3.6.1.4.1.1141.2.32.1.1.11 | Gauge32 | read-only | Represents the number of cells received in the previous 15 minute period. |
| G32 hcxPortPrevMinUncorrFecHecCells | 1.3.6.1.4.1.1141.2.32.1.1.12 | Gauge32 | read-only | Represents the number of received cells with either uncorrectable FEC or HEC errors in the previous 15 minute period. |
| INT hcxPortRatioThresPeriod | 1.3.6.1.4.1.1141.2.32.1.1.21 | INTEGER | read-write | This attribute defines the integration period for the error ratio thresholds. This attribute defines the number of seconds over which the threshold is contiguously exceeded before a trap is generated. 0 disables the thresholds. Default is 5. |
| I32 hcxPortRealTimeMaxNoise | 1.3.6.1.4.1.1141.2.32.1.1.30 | Integer32 | read-only | This attribute provides a realtime max noise level in dBmv. The attribute is updated every approx 5 seconds and provides the maximum noise level during that period. |
| I32 hcxPortRealTimeMeanNoise | 1.3.6.1.4.1.1141.2.32.1.1.28 | Integer32 | read-only | This attribute provides a realtime mean noise level in dBmv. It is updated every approx 5 seconds and provides a snap shot of the noise conditions on this receiver port. |
| I32 hcxPortRealTimeMinNoise | 1.3.6.1.4.1.1141.2.32.1.1.29 | Integer32 | read-only | ::= { com21HcxUpstrmStatsEntry 29 } This attribute provides a realtime min noise level in dBmv. The attribute is updated every approx 5 seconds and provides the minimum noise level during that period. |
| INT hcxPortUpstreamUtil | 1.3.6.1.4.1.1141.2.32.1.1.16 | INTEGER | read-only | Represents the percentage of utilization on all slots of the upstream channel. |
| UPS hcxRecvFrequency | 1.3.6.1.4.1.1141.2.31.1.1.4 | UpstrmFreqKhz | read-write | Contains the receive frequency of the RF board in KHz. Note that any change to this frequency shall result in temporary loss of service for the ComPorts as the RX needs to issue a frquency change message to each ComPort in turn. Also note that the CC shall check for frequency overlap with other RX cards within the group - the RX channels can be no closer than 1.8Mhz. With the advent of frequency hopping this attribute defines the primary frequency. Minimum step size is 50. i.e. 50000hz. Default is 0. |
| INT hcxRecvPower | 1.3.6.1.4.1.1141.2.31.1.1.5 | INTEGER | read-write | Contains the receiver power level in dBmv. Default is 0. |
| G32 hcxRfAnalysisBin1Count | 1.3.6.1.4.1.1141.2.37.1.1.10 | Gauge32 | read-only | This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint1 and hcxRfAnalysisPoint2. |
| G32 hcxRfAnalysisBin2Count | 1.3.6.1.4.1.1141.2.37.1.1.11 | Gauge32 | read-only | This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint2 and hcxRfAnalysisPoint3. |
| G32 hcxRfAnalysisBin3Count | 1.3.6.1.4.1.1141.2.37.1.1.12 | Gauge32 | read-only | This attribute respresents the number of noise samples with levels between hcxRfAnalysisPoint3 and hcxRfAnalysisPoint4. |
| INT hcxRfAnalysisClearCount | 1.3.6.1.4.1.1141.2.37.1.1.13 | INTEGER | read-write | This attribute is used to clear the three RF analysis counts. |
| INT hcxRfAnalysisControl | 1.3.6.1.4.1.1141.2.37.1.1.5 | INTEGER | read-write | Used to activate or deactivate the RF analysis for a port or I-Port. Default disable. |
| RFA hcxRfAnalysisPoint1 | 1.3.6.1.4.1.1141.2.37.1.1.6 | RfAnalysisdBmv | read-write | This attribute is used to define the first, and lowest, noise level point. Default is -58dBmv. |
| RFA hcxRfAnalysisPoint2 | 1.3.6.1.4.1.1141.2.37.1.1.7 | RfAnalysisdBmv | read-write | This attribute is used to define the second noise level point. This value must be greater than hcxRfAnalysisPoint1. Default is -15dBmv. |
| RFA hcxRfAnalysisPoint3 | 1.3.6.1.4.1.1141.2.37.1.1.8 | RfAnalysisdBmv | read-write | This attribute is used to define the third noise level point. This value must be greater than hcxRfAnalysisPoint2. Default is -10dBmv. |
| RFA hcxRfAnalysisPoint4 | 1.3.6.1.4.1.1141.2.37.1.1.9 | RfAnalysisdBmv | read-write | This attribute is used to define the final noise level point. This value must be greater than hcxRfAnalysisPoint3. Default is -5dBmv. |
| I32 hcxRfAnalysisPortId | 1.3.6.1.4.1.1141.2.37.1.1.3 | Integer32 | read-only | contains upstream port id. Presently only one port is supported. |
| INT hcxRfAnalysisRpmPortId | 1.3.6.1.4.1.1141.2.37.1.1.4 | INTEGER | read-only | contains any RPM I-Port id. Note an RX card or RXM card operating without an RPM expects 1 for this attribute. |
| INT hcxRfAnalysisShelfId | 1.3.6.1.4.1.1141.2.37.1.1.1 | INTEGER | read-only | contains upstream shelf id. |
| I32 hcxRfAnalysisSlotId | 1.3.6.1.4.1.1141.2.37.1.1.2 | Integer32 | read-only | contains upstream slot id. |
| INT hcxRpmCellErrRatioThres | 1.3.6.1.4.1.1141.2.36.1.1.23 | INTEGER | read-write | This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of FEC/HEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxRpmRatioThresPeriod attribute before a trap is generated. In addition the cells received within one second must be greater than that defined by hcxRpmMinErrRatioCells. A value of 0 disables the threshold. Default is 10. |
| NTF hcxRpmCellErrRatioThresTrap | 1.3.6.1.4.1.1141.4.85 | Severity is WARNING. | ||
| INT hcxRpmClearStats | 1.3.6.1.4.1.1141.2.36.1.1.27 | INTEGER | read-write | This attribute is used to clear all RPM statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr. |
| INT hcxRpmCnrThres | 1.3.6.1.4.1.1141.2.36.1.1.26 | INTEGER | read-write | Defines the average noise level, in dBmv, at which a frequency hop should occur. Note that the data error thresholds define above take precedence - this CNR threshold applies only if the data rate is less than the hcxRpmMinErrRatioCells. Default 11dBmv. |
| NTF hcxRpmCnrThresTrap | 1.3.6.1.4.1.1141.4.86 | Tbd. Severity is WARNING. | ||
| INT hcxRpmCorrFecRatioThres | 1.3.6.1.4.1.1141.2.36.1.1.22 | INTEGER | read-write | This attribute defines a threshold point at which a hop of the receive channel frequency shall take place. The threshold is defined as the percentage of corrected FEC errored cells to good cells. The RX card shall calculate this percentage over a one second period, and the threshold must be crossed for the period defined by the hcxRpmRatioThresPeriod attribute before a trap is generated. In addition the cells received within the second must be greater than that defined by hcxRpmMinErrRatioCells. A value of 0 disables the threshold. Default is 20. |
| I32 hcxRpmCurrMaxNoise | 1.3.6.1.4.1.1141.2.36.1.1.11 | Integer32 | read-only | Defines the maximum noise level, in dBmv, sampled on the I-Port in the current 15 minute period. |
| I32 hcxRpmCurrMeanNoise | 1.3.6.1.4.1.1141.2.36.1.1.9 | Integer32 | read-only | This attribute defines the mean noise value, in dBmv, sampled on the I-Port in the current 15 minute period. |
| G32 hcxRpmCurrMinCorrectedFec | 1.3.6.1.4.1.1141.2.36.1.1.8 | Gauge32 | read-only | Represents the number of corrected FEC errors received via the I-Port in the current 15 minute period. |
| I32 hcxRpmCurrMinNoise | 1.3.6.1.4.1.1141.2.36.1.1.10 | Integer32 | read-only | Defines the minimum noise level, in dBmv, sampled on the I-Port in the current 15 minute period. |
| G32 hcxRpmCurrMinRxCells | 1.3.6.1.4.1.1141.2.36.1.1.5 | Gauge32 | read-only | Represents the number of cells received via the I-Port in the current 15 minute period. |
| G32 hcxRpmCurrMinRxNullCells | 1.3.6.1.4.1.1141.2.36.1.1.6 | Gauge32 | read-only | Represents the number of null cells received via the RPM I-Port in the current 15 minute period. |
| G32 hcxRpmCurrMinUncorFecHecCells | 1.3.6.1.4.1.1141.2.36.1.1.7 | Gauge32 | read-only | Represents the number of received cells with either uncorrectable FEC or HEC errors received via the I-Port in the current 15 minute period. |
| NTF hcxRpmFecRatioThres | 1.3.6.1.4.1.1141.4.84 | Severity is WARNING. | ||
| NTF hcxRpmInvalidConfClear | 1.3.6.1.4.1.1141.4.88 | this trap is generated once the actual and configured RPM configuration match. Severity is CLEARED. | ||
| NTF hcxRpmInvalidPhyConfig | 1.3.6.1.4.1.1141.4.87 | this trap is generated whenever the actual RPM configuration does not match that defined by the hcxUpstrmRpmControl attribute above. Default severity is MINOR. | ||
| INT hcxRpmIPortConfigState | 1.3.6.1.4.1.1141.2.35.1.1.6 | INTEGER | read-write | Used to activate or deactivate the I-Port. For test purposes, one port can be enabled and all others disabled. This will cause the I-Port to be permanently closed. i.e. traffic passing. Default disable. Note that setting an I-Port to the disabled state will have the effect of clearing the statistics for the I-Port. |
| INT hcxRpmIPortContSchedType | 1.3.6.1.4.1.1141.2.35.1.1.7 | INTEGER | read-write | Used to control the type of contention slot scheduling utilized by this I-Port. The roundRobinOperation indicates that this I-Port shall have a individual contention opportunity - i.e. no other I-Ports active - allocated on a round-robin basis. The simultaneousOperation indicates that this I-Port shall be included with a group of I-Ports given the same, simultaneous contention opportunities. Default is roundRobinOperation. |
| INT hcxRpmIPortId | 1.3.6.1.4.1.1141.2.35.1.1.4 | INTEGER | read-only | Contains the id for the RPM I-port. |
| INT hcxRpmIPortRecvPower | 1.3.6.1.4.1.1141.2.35.1.1.5 | INTEGER | read-write | Contains the receiver power level in dBmv. Default is 0. |
| INT hcxRpmIPortShelfId | 1.3.6.1.4.1.1141.2.35.1.1.1 | INTEGER | read-only | contains upstream shelf id containing the RX card. |
| I32 hcxRpmIPortSlotId | 1.3.6.1.4.1.1141.2.35.1.1.2 | Integer32 | read-only | contains upstream slot id containing the port. Presently there is one port per card. |
| NTF hcxRpmLinkErrClear | 1.3.6.1.4.1.1141.4.132 | this trap is generated once a previously reported RPM link error is cleared. Severity is CLEARED. | ||
| NTF hcxRpmLinkError | 1.3.6.1.4.1.1141.4.131 | this trap is generated whenever the link between the RPM and RxM is detected as down or in error. Default severity is MINOR. | ||
| INT hcxRpmMinErrRatioCells | 1.3.6.1.4.1.1141.2.36.1.1.25 | INTEGER | read-write | This attribute defines the minimum number of cells that should be received per second in order to allow the Error and Corrected Cell Thresholds to cause a frequency hop. Default is 50. |
| I32 hcxRpmPrevMaxNoise | 1.3.6.1.4.1.1141.2.36.1.1.21 | Integer32 | read-only | Defines the maximum noise level, in dBmv, sampled on the I-Port in the previous 15 minute period. |
| I32 hcxRpmPrevMeanNoise | 1.3.6.1.4.1.1141.2.36.1.1.19 | Integer32 | read-only | This attribute defines the mean noise value, in dBmv, sampled on the I-Port in the previous 15 minute period. |
| G32 hcxRpmPrevMinCorrectedFec | 1.3.6.1.4.1.1141.2.36.1.1.18 | Gauge32 | read-only | Represents the number of corrected FEC errors in the previous 15 minute period. |
| I32 hcxRpmPrevMinNoise | 1.3.6.1.4.1.1141.2.36.1.1.20 | Integer32 | read-only | Defines the minimum noise level, in dBmv, sampled on the I-Port in the previous 15 minute period. |
| G32 hcxRpmPrevMinRxCells | 1.3.6.1.4.1.1141.2.36.1.1.15 | Gauge32 | read-only | Represents the number of cells received via the RPM I-Port in the previous 15 minute period. |
| G32 hcxRpmPrevMinRxNullCells | 1.3.6.1.4.1.1141.2.36.1.1.16 | Gauge32 | read-only | Represents the number of null cells received via the I-Port in the previous 15 minute period. |
| G32 hcxRpmPrevMinUncorFecHecCells | 1.3.6.1.4.1.1141.2.36.1.1.17 | Gauge32 | read-only | Represents the number of cells with uncorrectable FEC or HEC errors received via the I-Port in the previous 15 minute period. |
| INT hcxRpmRatioThresPeriod | 1.3.6.1.4.1.1141.2.36.1.1.24 | INTEGER | read-write | This attribute defines the integration period for the error ratio thresholds. This attribute defines the number of seconds over which the threshold is contiguously exceeded before a trap is generated. 0 disables the thresholds. Default is 5. |
| I32 hcxRpmRealTimeMaxNoise | 1.3.6.1.4.1.1141.2.36.1.1.14 | Integer32 | read-only | This attribute provides a realtime max noise level in dBmv sampled on the I-Port. The attribute is updated every approx 5 seconds and provides the maximum noise level during that period. |
| I32 hcxRpmRealTimeMeanNoise | 1.3.6.1.4.1.1141.2.36.1.1.12 | Integer32 | read-only | This attribute provides a realtime mean noise level in dBmv sampled on the I-Port. It is updated every approx 5 seconds and provides a snap shot of the noise conditions on this I-Port. |
| I32 hcxRpmRealTimeMinNoise | 1.3.6.1.4.1.1141.2.36.1.1.13 | Integer32 | read-only | This attribute provides a realtime min noise level in dBmv sampled on the I-Port. The attribute is updated every approx 5 seconds and provides the minimum noise level during that period. |
| I32 hcxRpmRxPortId | 1.3.6.1.4.1.1141.2.35.1.1.3 | Integer32 | read-only | Contains the id for the upstream port. Presently should be one only. |
| NTF hcxRpmTimingFault | 1.3.6.1.4.1.1141.4.89 | this trap is generated whenever an RPM timing problem is detected. Default severity is MINOR. | ||
| NTF hcxRpmTimingFaultClear | 1.3.6.1.4.1.1141.4.130 | this trap is generated once a previously detected RPM timing problem is cleared. Severity is CLEARED. | ||
| NTF hcxRxFreqHop | 1.3.6.1.4.1.1141.4.82 | This trap is generated when an RX port frequency is hopped due to errors. The hcxUpstrmActiveFreq varbind indicates the new frequency. Severity is WARNING. | ||
| INT hcxStatsClearStats | 1.3.6.1.4.1.1141.2.34.1.1.17 | INTEGER | read-write | This attribute is used to clear all RX ComPort statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr. |
| I32 hcxStatsCurrMinCorFecThres | 1.3.6.1.4.1.1141.2.34.1.1.9 | Integer32 | read-write | Represents the number of corrected FEC errors in the present 15minute period that shall cause a threshold trap to be generated. Default is 0 - threshold disabled. |
| G32 hcxStatsCurrMinCorrectedFec | 1.3.6.1.4.1.1141.2.34.1.1.8 | Gauge32 | read-only | Represents the number of corrected FEC errors for this ComPort/VCI in the current 15 minute period. |
| I32 hcxStatsCurrMinMeanSignal | 1.3.6.1.4.1.1141.2.34.1.1.15 | Integer32 | read-only | This attribute contains the mean signal strength value in dBmv sampled for this ComPort in the current 15 minute period. |
| G32 hcxStatsCurrMinRxCells | 1.3.6.1.4.1.1141.2.34.1.1.2 | Gauge32 | read-only | Represents the number of cells successfully received in the current 15 minute period. |
| G32 hcxStatsCurrMinRxNullCells | 1.3.6.1.4.1.1141.2.34.1.1.3 | Gauge32 | read-only | Represents the number of null cells received in the current 15 minute period. |
| G32 hcxStatsCurrMinUncorFecHec | 1.3.6.1.4.1.1141.2.34.1.1.6 | Gauge32 | read-only | Represents the number of bad cells - HEC/Uncorrectable FEC/ Collisions - reported in cell slots allocated to this ComPort/VCI in the current 15 minute period. |
| I32 hcxStatsCurrMinUncorFecThres | 1.3.6.1.4.1.1141.2.34.1.1.7 | Integer32 | read-write | Represents the number of HEC/Uncorrectable FEC error cells received in the present 15minute period that shall cause a threshold trap to be generated. Default is 0 - threshold disabled. |
| G32 hcxStatsPrevMinCorrectedFec | 1.3.6.1.4.1.1141.2.34.1.1.14 | Gauge32 | read-only | Represents the number of corrected FEC errors for this ComPort/VCI in the previous 15 minute period. |
| I32 hcxStatsPrevMinMeanSignal | 1.3.6.1.4.1.1141.2.34.1.1.16 | Integer32 | read-only | This attribute contains the mean signal strength value in dBmv sampled for this ComPort in the previous 15 minute period. |
| G32 hcxStatsPrevMinRxCells | 1.3.6.1.4.1.1141.2.34.1.1.10 | Gauge32 | read-only | Represents the number of cells successfully received in the previous 15 minute period. |
| G32 hcxStatsPrevMinRxNullCells | 1.3.6.1.4.1.1141.2.34.1.1.11 | Gauge32 | read-only | Represents the number of null cells received in the previous 15 minute period. |
| G32 hcxStatsPrevMinUncorFecHec | 1.3.6.1.4.1.1141.2.34.1.1.13 | Gauge32 | read-only | Represents the number of bad cells - HEC/Uncorrectable FEC/Collisions - reported in cell slots allocated to this ComPort/VCI in the previous 15 minute period. |
| INT hcxStatsRpmIPortId | 1.3.6.1.4.1.1141.2.36.1.1.4 | INTEGER | read-only | Contains the id for the RPM I-Port. |
| INT hcxStatsRpmShelfId | 1.3.6.1.4.1.1141.2.36.1.1.1 | INTEGER | read-only | Contains the id for the shelf in which the associated RX card is located. |
| I32 hcxStatsRpmSlotId | 1.3.6.1.4.1.1141.2.36.1.1.2 | Integer32 | read-only | Contains the id for the upstream slot. |
| I32 hcxStatsRxPortId | 1.3.6.1.4.1.1141.2.36.1.1.3 | Integer32 | read-only | Contains the id for the upstream port. |
| I32 hcxStatsUpstreamPortId | 1.3.6.1.4.1.1141.2.32.1.1.3 | Integer32 | read-only | Contains the id for the upstream port. Between 1 and 12 |
| INT hcxStatsUpstreamShelfId | 1.3.6.1.4.1.1141.2.32.1.1.1 | INTEGER | read-only | Contains the id for the shelf in which the associated RX card is located. |
| I32 hcxStatsUpstreamSlotId | 1.3.6.1.4.1.1141.2.32.1.1.2 | Integer32 | read-only | Contains the id for the upstream slot. |
| MAC hcxStuStatsMacAddr | 1.3.6.1.4.1.1141.2.34.1.1.1 | MacAddress | read-only | Contains IEEE 802 medium access control address of the ComPort device. |
| NTF hcxUncorFecHecMinThres | 1.3.6.1.4.1.1141.4.37 | Severity is WARNING. | ||
| INT hcxUpDiagTestAction | 1.3.6.1.4.1.1141.2.33.1.1.11 | INTEGER | read-write | This attribute is used to invoke the internal RX diagnostic test. In order to activate this test, the card must be placed in the test state. |
| NTF hcxUpDiagTestComplete | 1.3.6.1.4.1.1141.4.32 | This notification is generated whenever the RX internal diagnostic tests are completed. This an event with no clear condition. Only severity is WARNING. | ||
| INT hcxUpDiagTestResult | 1.3.6.1.4.1.1141.2.33.1.1.12 | INTEGER | read-only | This attribute contains the result of the last RX diagnostic test. |
| INT hcxUpFaultStatusLed | 1.3.6.1.4.1.1141.2.33.1.1.14 | INTEGER | read-only | The RX Fault Status LED is a read-only attribute which describes the condition of the RX Fault Status light emitting diode located on the RX board. A value of on(1) indicates that an fault condition has been detected (for which a trap will have been issued) and the LED is illuminated. off if no card present. |
| NTF hcxUpFaultStatusLedChange | 1.3.6.1.4.1.1141.4.34 | generated whenever there is a change in the Fault LED status. This an event with no clear condition. Only severity is WARNING. | ||
| NTF hcxUpOperationFailure | 1.3.6.1.4.1.1141.4.35 | This notification is generated by the CC whenever an RX card fails to respond correctly to a request. This failure could indicate either a resource problem or software failure. Note that if an RX card failures to respond completely to a CC request, then a hcxInsertChange trap shall be generated. This an event with no clear condition. Only severity is WARNING. | ||
| STR hcxUpstreamBootVersion | 1.3.6.1.4.1.1141.2.33.1.1.4 | DisplayString | read-only | contains the version of the RX card boot ROM. This will be an empty string if card is missing. |
| INT hcxUpstreamGroupId | 1.3.6.1.4.1.1141.2.33.1.1.9 | INTEGER | read-write | The Upstream group id defines the receiver group to which this RF Receiver belongs. The shall ensure that the group contains a single RF Receiver card operating as an ComPort acquirer. Default is group 1. |
| STR hcxUpstreamHardwareVersion | 1.3.6.1.4.1.1141.2.33.1.1.3 | DisplayString | read-only | contains the hardware version of the RX card. Will be empty if card not present. |
| I32 hcxUpstreamPortId | 1.3.6.1.4.1.1141.2.31.1.1.3 | Integer32 | read-only | Contains the id for the upstream port. Presently should be one only. |
| STR hcxUpstreamSerialNumber | 1.3.6.1.4.1.1141.2.33.1.1.15 | DisplayString | read-only | contains the serial number of the RX card. This will be an empty string if card is missing. |
| INT hcxUpstreamShelfId | 1.3.6.1.4.1.1141.2.33.1.1.1 | INTEGER | read-only | contains upstream shelf id. |
| I32 hcxUpstreamSlotId | 1.3.6.1.4.1.1141.2.33.1.1.2 | Integer32 | read-only | contains upstream unit id. This is the slot number. |
| INT hcxUpstreamUnitConfigState | 1.3.6.1.4.1.1141.2.33.1.1.7 | INTEGER | read-write | The Upstream Unit State is an active-value. Offline will disable the RF and all other cell forwarding. Online enables RF and performs all traffic and scheduling functions. Test will also place the card offline but shall allow a diagnostic test. Maintenance keeps RF alive but RX performs no scheduling. Note that RX card will not enter the maintenance state if there are any authorized ComPorts. It is the responsibility of the CC to hop any ComPorts prior to entering this state. Offline is default. |
| PRI hcxUpstreamUnitPrimServState | 1.3.6.1.4.1.1141.2.33.1.1.5 | PrimServiceState | read-only | contains primary service state of the Upstream Unit. |
| NTF hcxUpstreamUnitPrimStateChange | 1.3.6.1.4.1.1141.4.30 | Generated whenever a the hcxUpstreamUnitPrimServState changes in value. This an event with no clear condition. Only severity is WARNING. | ||
| INT hcxUpstreamUnitRestartAction | 1.3.6.1.4.1.1141.2.33.1.1.8 | INTEGER | read-write | The RX Unit Restart Action is an active-value. The setting of this attribute to restart(2) causes the RX card to reset and download a new image. |
| STR hcxUpstreamUnitSecServState | 1.3.6.1.4.1.1141.2.33.1.1.6 | DisplayString | read-only | contains a string defining the secondary service states of the Upstream Unit. The substrings supported by the Upstream Unit shall be: TEST - in test, as set by hcxUpstreamUnitConfigState, MT - offline, again set by hcxUpstreamUnitConfigState, FAULT - hardware failure, UNEQ - unequipped. |
| NTF hcxUpstreamUnitSecStateChange | 1.3.6.1.4.1.1141.4.31 | Generated whenever a the hcxUpstreamUnitSecServState changes in value. This an event with no clear condition. Only severity is WARNING. | ||
| UPS hcxUpstrmActiveFreq | 1.3.6.1.4.1.1141.2.31.1.1.12 | UpstrmFreqKhz | read-only | Contains the presently active frequency. i.e. primary, alternate A or alternate B. Upon initial deployment of the system this frequency will always match the primary frequency. Upon reboot, the RX port shall always return to this frequency. |
| I32 hcxUpstrmAggrStuCbrRate | 1.3.6.1.4.1.1141.2.31.1.1.6 | Integer32 | read-only | This attribute defines the aggregate of all ComPort upstream CBR rates on the RX port. Defined in Kbps. |
| I32 hcxUpstrmAggrStuMaxRate | 1.3.6.1.4.1.1141.2.31.1.1.8 | Integer32 | read-only | This attribute defines the aggregate of all ComPort upstream Maximum rates on the RX port. Defined in Kbps. |
| I32 hcxUpstrmAggrStuMinRate | 1.3.6.1.4.1.1141.2.31.1.1.7 | Integer32 | read-only | This attribute defines the aggregate of all ComPort upstream Minimum rates on the RX port. Defined in Kbps. |
| I32 hcxUpstrmAggrStuVoiceRate | 1.3.6.1.4.1.1141.2.31.1.1.17 | Integer32 | read-only | This attribute defines the aggregate of all ComPort upstream voice rates on the RX port. Defined in Kbps. |
| INT hcxUpstrmAltFreqA | 1.3.6.1.4.1.1141.2.31.1.1.10 | INTEGER | read-write | Contains the first alternate frequency for this RX port. This need NOT be unique. i.e. other RX ports within the receiver group can also share the same alternate frequencies. Valid values are 0 or 5000-40000KHz. 0 indicates no alternate frequency. If this frequency was being used by the receiver port and is set to 0 then the port shall revert back to the primary frequency. Minimum step size is 50. i.e. 50000hz. Default is 0. |
| INT hcxUpstrmAltFreqB | 1.3.6.1.4.1.1141.2.31.1.1.11 | INTEGER | read-write | Contains the second alternate frequency for this RX port. Same restrictions and defaults as for hcxUpstrmAltFreqA. |
| INT hcxUpstrmFreqHopping | 1.3.6.1.4.1.1141.2.31.1.1.9 | INTEGER | read-write | This attribute controls whether an RX port is protected by automatic frequency hopping. If this attribute is transitioned from on -> off then the RX port shall return to the primary frequency. This method can be used to force an RX port to a specific frequency if a hop away from the primary freq had previously occurred. Default will be on. |
| INT hcxUpstrmPortShelfId | 1.3.6.1.4.1.1141.2.31.1.1.1 | INTEGER | read-only | contains upstream shelf id containing the RX card. |
| I32 hcxUpstrmPortSlotId | 1.3.6.1.4.1.1141.2.31.1.1.2 | Integer32 | read-only | contains upstream slot id containing the port. Presently there is one port per card. |
| INT hcxUpstrmRpmConnType | 1.3.6.1.4.1.1141.2.31.1.1.16 | INTEGER | read-only | contains management connection type to the RPM device. Note that if the RxM is in slave mode, then the state information defined by the attributes above shall not be applicable. |
| INT hcxUpstrmRpmControl | 1.3.6.1.4.1.1141.2.31.1.1.13 | INTEGER | read-write | Defines RPM control. This attribute is only applicable in the case of an RXM card. For the RX card this attribute will be read-only with a value of notSupported. If the RPM is present then the control shall be validated against the physical configuration. If an attempt is made to place the RPM in 8 port mode but it is physically configured for 4 port, then an error response shall be return. Default for RxM is enable8Port. Option notSupported is unavailable for RxM. |
| PRI hcxUpstrmRpmPrimServState | 1.3.6.1.4.1.1141.2.31.1.1.14 | PrimServiceState | read-only | contains primary service state of the RPM. |
| NTF hcxUpstrmRpmPrimStateChange | 1.3.6.1.4.1.1141.4.133 | Generated whenever a the hcxUpstrmRpmPrimServState changes in value. This an event with no clear condition. Only severity is WARNING. | ||
| STR hcxUpstrmRpmSecServState | 1.3.6.1.4.1.1141.2.31.1.1.15 | DisplayString | read-only | contains a string defining the secondary service states of the RPM. The substrings supported by the RPM shall be: UNEQ - not present, CONF - invalid configuration, LINK - link fault, TIME - timing fault. |
| INT hcxUpTestStatusLed | 1.3.6.1.4.1.1141.2.33.1.1.13 | INTEGER | read-only | The RX Test Status LED is a read-only attribute which describes the condition of the RX Test Status light emitting diode located on the RX board. A value of on(1) indicates that a service effecting test is in progress and that the LED is illuminated. off if no card present. |
| NTF hcxUpTestStatusLedChange | 1.3.6.1.4.1.1141.4.33 | generated whenever there is a change in test LED status. This an event with no clear condition. Only severity is WARNING. |
RFC description
Com21 ComController RX card MIB for managing upstream RF receive functionality. Monitors RF signal characteristics, statistics, and ILMI-related objects.
Start monitoring Com21 ComController HCX downstream RX card (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.