All MIBs › CISCO-VISM-MODULE-MIB › vismBearerContinuityTimer
vismBearerContinuityTimer
Module: CISCO-VISM-MODULE-MIB
OID (symbolic): CISCO-VISM-MODULE-MIB::vismBearerContinuityTimer
OID (numeric): 1.3.6.1.4.1.351.110.3.17.4.15
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: This object specifies the co4 (bearer continuity) timer in millisecs.
The timer will be started in the terminating/originating gateway for a duration as specified in this MIB object when a co3 message is sent from the terminating/originating gateway to the originating/terminating gateway.
If the terminating/originating gateway does not receive co4 as an acknowledgement from the originating/termintaing gateway and the timer expires, gateway initiated DLCX is sent to the call agent from the terminating/originating gateway.
This object is applicable when the call agent feature is available.
What is vismBearerContinuityTimer?
This read-write Integer32 (0-10000) sets, in milliseconds, how long a terminating or originating gateway waits for a co4 acknowledgment after sending a co3 bearer continuity message. An admin cares because if the co4 response does not arrive within this window, the gateway concludes the continuity test failed, which affects whether a call is allowed to proceed. For example, a network engineer troubleshooting frequent call setup failures might lengthen this timer to accommodate a WAN link with higher round-trip latency between originating and terminating VISM gateways.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.3.17.4.15 snmpwalk -v2c -c public <target> CISCO-VISM-MODULE-MIB::vismBearerContinuityTimer
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.3.17.4.15.1 snmpget -v2c -c public <target> CISCO-VISM-MODULE-MIB::vismBearerContinuityTimer.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.3.17.4.15.1 i <value>
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VISM-MODULE-MIB::vismBearerContinuityTimer OID value, configure state conditions and alerts, and monitor any Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.3 | cardSpecific | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.3.17 | vismConfig | CISCO-VISM-MODULE-MIB |
| 1.3.6.1.4.1.351.110.3.17.4 | vismSystemGrp | CISCO-VISM-MODULE-MIB |
| 1.3.6.1.4.1.351.110.3.17.4.15 | vismBearerContinuityTimer | CISCO-VISM-MODULE-MIB |