| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoHsrpExtMIB | 1.3.6.1.4.1.9.9.107 | | | The Extension MIB module for the CISCO-HSRP-MIB which is
based on RFC2281.
This MIB provides an extension to the CISCO-HSRP-MIB which
defines Cisco's proprietary Hot Standby Routing Protocol
(HSRP), defined in RFC2281. The extensions cover assigning
of secondary HSRP ip addresses, modifying an HSRP Group's
priority by tracking the operational status of interfaces,
etc.
Terminology:
HSRP is a protocol used amoung a group of routers for the
purpose of selecting an active router and a standby router.
An active router is the router of choice for routing
packets.
A standby router is a router that takes over the routing
duties when an active router fails, or when preset
conditions have been met.
A HSRP group or a standby group is a set of routers
which communicate using HSRP. An HSRP group has a group
MAC address and a group IP address. These are the
designated addresses. The active router assumes
(i.e. inherits) these group addresses. An HSRP group is
identified by a ( ifIndex, cHsrpGrpNumber ) pair.
BIA stands for Burned In Address. |
| ciscoHsrpExtMIBObjects | 1.3.6.1.4.1.9.9.107.1 | | | |
| cHsrpExtGroup | 1.3.6.1.4.1.9.9.107.1.1 | | | |
| cHsrpExtIfTrackedTable | 1.3.6.1.4.1.9.9.107.1.1.1 | | not-accessible | A table containing information about tracked interfaces per
HSRP group. |
| cHsrpExtIfTrackedEntry | 1.3.6.1.4.1.9.9.107.1.1.1.1 | | not-accessible | Each row of this table allows the tracking of one
interface of the HSRP group which is identified by the
(ifIndex, cHsrpGrpNumber) values in this table's INDEX clause.
Weight(priority) is given to each and every interface tracked.
When a tracked interface is unavailable, the HSRP priority of
the router is decreased. i.e cHsrpGrpPriority value assigned
to an HSRP group will reduce by the value assigned to
cHsrpExtIfTrackedPriority. This reduces the likelihood
of a router with a failed key interface becoming the
active router.
Setting cHsrpExtIfTrackedRowStatus to active starts
the tracking of cHsrpExtIfTracked by the HSRP group.
The value of cHsrpExtIfTrackedRowStatus may be set
to destroy at any time.
Entries may not be created via SNMP without explicitly setting
cHsrpExtIfTrackedRowStatus to either 'createAndGo'
or 'createAndWait'.
Entries can be created and modified via the management
protocol or by the device's local management interface.
If the row is not active, and a local management interface
command modifies that row, the row may transition to active
state.
A row entry in the cHsrpExtIfTrackedTable can not be created
unless the corresponding row in the cHsrpGrpTable has been
created. If that corresponding row in cHsrpGrpTable is
deleted, the interfaces it tracks also get deleted.
A row which is not in active state will timeout after a
configurable period (five minutes by default). This timeout
period can be changed by setting cHsrpConfigTimeout. |
| NUM cHsrpExtIfTracked | 1.3.6.1.4.1.9.9.107.1.1.1.1.1 | InterfaceIndex | not-accessible | The ifIndex value of the tracked interface. |
| U32 cHsrpExtIfTrackedPriority | 1.3.6.1.4.1.9.9.107.1.1.1.1.2 | Unsigned32 | read-create | Priority of the tracked interface for the corresponding
{ ifIndex, cHsrpGrpNumber } pair. In the range of 0 to 255, 0
is the lowest priority and 255 is the highest. When a tracked
interface is unavailable, the cHsrpGrpPriority of the router
is decreased by the value of this object instance (If the
cHsrpGrpPriority is less than the
cHsrpExtIfTrackedPriority, then the HSRP priority
becomes 0). This allows a standby router to be configured
with a priority such that if the currently active router's
priority is lowered because the tracked interface goes down,
the standby router can takeover. |
| ROW cHsrpExtIfTrackedRowStatus | 1.3.6.1.4.1.9.9.107.1.1.1.1.3 | RowStatus | read-create | The control that allows modification, creation, and deletion
of entries. For detailed rules see the DESCRIPTION for
cHsrpExtIfTrackedEntry. |
| T/F cHsrpExtIfTrackedIpNone | 1.3.6.1.4.1.9.9.107.1.1.1.1.4 | TruthValue | read-create | This object specifies the disable HSRP IPv4 virtual
IP address. |
| cHsrpExtSecAddrTable | 1.3.6.1.4.1.9.9.107.1.1.2 | | not-accessible | A table containing information about secondary HSRP IP
Addresses per interface and group. |
| cHsrpExtSecAddrEntry | 1.3.6.1.4.1.9.9.107.1.1.2.1 | | not-accessible | The CHsrpExtSecAddrEntry allows creation of secondary
IP Addresses for each cHsrpGrpEntry row.
Secondary addresses can be added by setting
cHsrpExtSecAddrRowStatus to be active. The value of
cHsrpExtSecAddrRowStatus may be set to destroy at any
time.
Entries may not be created via SNMP without explicitly setting
cHsrpExtSecAddrRowStatus to either 'createAndGo'
or 'createAndWait'.
Entries can be created and modified via the management
protocol or by the device's local management interface.
If the row is not active, and a local management interface
command modifies that row, the row may transition to active
state.
A row which is not in active state will timeout after a
configurable period (five minutes by default). This timeout
period can be changed by setting cHsrpConfigTimeout.
Before creation of a cHsrpExtSecAddrEntry row,
either cHsrpGrpConfiguredVirtualIpAddr or
cHsrpGrpLearnedVirtualIpAddr must have a valid IP Address.
This is because a secondary ip address cannot be created
unless the primary ip address has already been set.
To create a new cHsrpExtSecAddrEntry row, a management
station should choose the ifIndex of the interface which is to
be added as part of an HSRP group. Also, an HSRP group number
and a cHsrpExtSecAddrAddress should be chosen.
Deleting a {ifIndex, cHsrpGrpNumber} row in the
cHsrpGrpTable will delete all corresponding
rows in the cHsrpExtSecAddrTable.
Deleting a primary address value in the cHsrpGrpEntry row
will delete all secondary addresses for the same
{ifIndex, cHsrpGrpNumber} pair. |
| IP cHsrpExtSecAddrAddress | 1.3.6.1.4.1.9.9.107.1.1.2.1.1 | IpAddress | not-accessible | A secondary IpAddress for the {ifIndex, cHsrpGrpNumber} pair.
As explained in the DESCRIPTION for cHsrpExtSecAddrEntry, a
primary address must exist before a secondary address for
the same {ifIndex, cHsrpGrpNumber} pair can be created. |
| ROW cHsrpExtSecAddrRowStatus | 1.3.6.1.4.1.9.9.107.1.1.2.1.2 | RowStatus | read-create | The control that allows modification, creation, and deletion
of entries. For detailed rules see the DESCRIPTION for
cHsrpExtSecAddrEntry. |
| cHsrpExtIfStandbyTable | 1.3.6.1.4.1.9.9.107.1.1.3 | | not-accessible | A table containing information about standby
interfaces per HSRP group. |
| cHsrpExtIfStandbyEntry | 1.3.6.1.4.1.9.9.107.1.1.3.1 | | not-accessible | The cHsrpExtIfStandbyEntry allows an HSRP group
interface to track one or more standby interfaces.
To create a new cHsrpExtIfStandbyEntry row, a
management station should choose the ifIndex of
the interface which is to be added as part of an
HSRP group. Also, an HSRP group number and a
cHsrpExtIfStandbyIndex should be chosen. |
| U32 cHsrpExtIfStandbyIndex | 1.3.6.1.4.1.9.9.107.1.1.3.1.1 | Unsigned32 | not-accessible | This object defines the index of the standby table. |
| IPt cHsrpExtIfStandbyDestAddrType | 1.3.6.1.4.1.9.9.107.1.1.3.1.2 | InetAddressType | read-create | This object specifies the type of Internet address
denoted by cHsrpExtIfStandbyDestAddr. |
| IP cHsrpExtIfStandbyDestAddr | 1.3.6.1.4.1.9.9.107.1.1.3.1.3 | InetAddress | read-create | This object specifies the destination IP address of
the standby router. |
| IPt cHsrpExtIfStandbySourceAddrType | 1.3.6.1.4.1.9.9.107.1.1.3.1.4 | InetAddressType | read-create | This object specifies the type of Internet address
denoted by cHsrpExtIfStandbySourceAddr. |
| IP cHsrpExtIfStandbySourceAddr | 1.3.6.1.4.1.9.9.107.1.1.3.1.5 | InetAddress | read-create | This object specifies the source IP address of
the standby router. |
| ROW cHsrpExtIfStandbyRowStatus | 1.3.6.1.4.1.9.9.107.1.1.3.1.6 | RowStatus | read-create | The control that allows modification, creation,
and deletion of entries. Entries may not be created
via SNMP without explicitly setting
cHsrpExtIfStandbyRowStatus to either
'createAndGo' or 'createAndWait'. |
| cHsrpExtIfBIA | 1.3.6.1.4.1.9.9.107.1.2 | | | |
| cHsrpExtIfTable | 1.3.6.1.4.1.9.9.107.1.2.1 | | not-accessible | HSRP-specific configurations for each physical interface. |
| cHsrpExtIfEntry | 1.3.6.1.4.1.9.9.107.1.2.1.1 | | not-accessible | If HSRP entries on this interface must use the BIA (Burned
In Address), there must be an entry for the interface in this
table. Entries of this table are only accessible if HSRP has
been enabled i.e entries can not be created if HSRP is not
enabled. Also, the interfaces should be of IEEE 802 ones
(Ethernet, Token Ring, FDDI,VLAN, LANE, TR-LANE).
Setting cHsrpExtIfRowStatus to active initiates the
entry with default value for cHsrpExtIfUseBIA as FALSE.
The value of cHsrpExtIfRowStatus may be set to destroy
at any time. If the row is not initiated, it is similar to
having cHsrpExtIfUseBIA as FALSE.
Entries may not be created via SNMP without explicitly setting
cHsrpExtIfRowStatus to either 'createAndGo' or 'createAndWait'.
Entries can be created and modified via the management
protocol or by the device's local management interface.
If the row is not active, and a local management interface
command modifies that row, the row may transition to active
state.
A row which is not in active state will timeout after a
configurable period (five minutes by default). This timeout
period can be changed by setting cHsrpConfigTimeout. |
| T/F cHsrpExtIfUseBIA | 1.3.6.1.4.1.9.9.107.1.2.1.1.1 | TruthValue | read-create | If set to TRUE, the HSRP Group MAC Address for all groups
on this interface will be the burned-in-address. Otherwise,
this will be determined by ciscoHsrpGroupNumber. In case of
sub-interfaces, UseBIA applies to all sub-interfaces on an
interface and to all groups on those sub-interfaces. |
| ROW cHsrpExtIfRowStatus | 1.3.6.1.4.1.9.9.107.1.2.1.1.2 | RowStatus | read-create | The control that allows modification, creation, and deletion
of entries. For detailed rules see the DESCRIPTION for
cHsrpExtIfEntry. |
| cHsrpExtConformance | 1.3.6.1.4.1.9.9.107.3 | | | |
| cHsrpExtCompliances | 1.3.6.1.4.1.9.9.107.3.1 | | | |
| cHsrpExtCompliance | 1.3.6.1.4.1.9.9.107.3.1.1 | | | The compliance statement for entities which implement
the CISCO-HSRP-EXT-MIB. This is deprecated by
cHsrpExtComplianceRev1. |
| cHsrpExtComplianceRev1 | 1.3.6.1.4.1.9.9.107.3.1.2 | | | the compliance statement for entities which implement
the CISCO-HSRP-EXT-MIB.This is deprecated by
cHsrpExtComplianceRev2. |
| cHsrpExtComplianceRev2 | 1.3.6.1.4.1.9.9.107.3.1.3 | | | the compliance statement for entities which implement
the CISCO-HSRP-EXT-MIB. |
| cHsrpExtComplianceGroups | 1.3.6.1.4.1.9.9.107.3.2 | | | |
| cHsrpExtIfTrackedGroup | 1.3.6.1.4.1.9.9.107.3.2.1 | | | The collection of objects used to add, delete and retrieve
the interfaces getting tracked for HSRP groups. |
| cHsrpExtSecAddrGroup | 1.3.6.1.4.1.9.9.107.3.2.2 | | | The collection of objects used to add, delete and retrieve
primary and secondary Ip Addresses for HSRP groups. |
| cHsrpExtIfGroup | 1.3.6.1.4.1.9.9.107.3.2.3 | | | Object which tells if HSRP entries on this interface must
use BIA or not. |
| cHsrpExtIfStandbyGroup91 | 1.3.6.1.4.1.9.9.107.3.2.4 | | | The collection of objects used to add, delete and
retrieve the interfaces getting standby for
HSRP groups. |
| cHsrpExtIfTrackedGroupSup1 | 1.3.6.1.4.1.9.9.107.3.2.5 | | | The collection of HSRP interface tracked objects
which suppliments cHsrpExtIfTrackedGroup. |
