All MIBs › CISCO-DSPU-MIB
Organization: Cisco Systems, Inc.
Last Updated: 1995-08-15
Category: Cisco Devices, SNA and Legacy Protocols
Description: Handles Downstream Physical Unit (DSPU) SNA connectivity on Cisco devices, enabling emulation of IBM cluster controllers over IP networks.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-DSPU-MIB?
CISCO-DSPU-MIB is a Cisco enterprise MIB for managing Downstream Physical Unit (DSPU) functionality, which allows a Cisco router to emulate an IBM SNA cluster controller and carry legacy IBM mainframe/AS400 traffic over an IP or bridged Token Ring network. It exposes configuration objects for DSPU nodes and remote source-route bridging (RSRB) parameters (virtual ring numbers, bridge numbers, virtual MAC addresses), default PU session settings (window size, max I-frame size), and trap notifications tied to PU state changes. It is used to monitor the operational and software-configuration health of SNA/DSPU connectivity, including tracking the last configuration-change timestamp and receiving PU trap-based fault notifications when downstream physical units activate, deactivate, or fail. It relies on the Token Ring/RSRB addressing model (virtual rings and bridge numbers) shared with related bridging MIBs for its configuration semantics. It is typically deployed on Cisco routers acting as SNA gateways bridging legacy IBM 3270/5250 terminal traffic into modern IP networks. Engineers can download the CISCO-DSPU-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DSPU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco routers (legacy SNA DSPU gateway feature)
Monitoring Examples
An administrator monitoring SNA connectivity health would poll dspuNodeRsrb objects such as dspuNodeRsrbLocalVirtualRing, dspuNodeRsrbBridgeNumber, and dspuNodeRsrbVirtualMacAddress to confirm the RSRB bridging configuration matches the mainframe front-end processor, and check dspuNodeLastConfigChgTime to detect unexpected configuration drift. The dspuPoolClassTable/dspuPoolClassEntry lets an operator inspect PU pool-class assignments, while dspuPuTraps notifications alert when a downstream PU session fails or changes state, revealing SNA link instability.
What Can Be Monitored
- DSPU node RSRB bridging configuration
- PU session window size/max I-frame settings
- last configuration change time
- PU pool class assignments
- PU activation/deactivation trap events
This MIB depends on
Related MIBs
Imported Objects
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TimeStamp | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using dspuPuStatsSentBytes OID:
Select a Cisco router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dspuPuStatsSentBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of bytes sent by this PU. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoDspuMIB | 1.3.6.1.4.1.9.9.24 | Used to define and manage DSPU objects. | ||
| ciscoDspuMIBCompliance | 1.3.6.1.4.1.9.9.24.2.1.1 | The compliance statement for the SNMPv2 entities which implement the Cisco DSPU MIB. | ||
| ciscoDspuMIBCompliances | 1.3.6.1.4.1.9.9.24.2.1 | |||
| ciscoDspuMIBComplianceV11R01 | 1.3.6.1.4.1.9.9.24.2.1.2 | The compliance statement for the SNMPv2 entities which implement the Cisco DSPU MIB. | ||
| ciscoDspuMIBConformance | 1.3.6.1.4.1.9.9.24.2 | |||
| ciscoDspuMIBGroups | 1.3.6.1.4.1.9.9.24.2.2 | |||
| dspuLu | 1.3.6.1.4.1.9.9.24.1.5 | |||
| NTF dspuLuActivationFailureTrap | 1.3.6.1.4.1.9.9.24.1.5.3.0.2 | Generated whenever an LU activation failure is detected. The following information is returned: dspuPuOperName -> PU name dspuLuOperState -> Current operational state of the LU dspuLuOperLastActivationFailureReason -> Reason for LU activation failure | ||
| dspuLuAdminEntry | 1.3.6.1.4.1.9.9.24.1.5.1.1 | not-accessible | Each entry represents a defined LU owned by the PU. | |
| INT dspuLuAdminLuLocalAddress | 1.3.6.1.4.1.9.9.24.1.5.1.1.1 | INTEGER | not-accessible | NAU address of the local LU. |
| INT dspuLuAdminPeerLuLocalAddress | 1.3.6.1.4.1.9.9.24.1.5.1.1.5 | INTEGER | read-create | For downstream LUs, the PeerLuLocalAddress identifies the NAU address of the upstream LU to which this downstream LU is assigned. For upstream LUs, the PeerLuLocalAddress identifies the NAU address of the downstream LU to which this upstream LU is assigned. The PeerLuLocalAddress is valid for dedicated LUs only; otherwise, the PeerLuLocalAddress is zero. |
| I32 dspuLuAdminPeerPuIndex | 1.3.6.1.4.1.9.9.24.1.5.1.1.4 | Integer32 | read-create | For downstream LUs, the PeerPuIndex identifies the upstream PU that owns the upstream LU to which this downstream LU is assigned. For upstream LUs, the PeerPuIndex identifies the downstream PU that owns the downstream LU to which this upstream LU is assigned. The PeerPuIndex is valid for dedicated LUs only; otherwise, the PeerPuIndex is zero. |
| STR dspuLuAdminPoolClassName | 1.3.6.1.4.1.9.9.24.1.5.1.1.3 | DisplayString | read-create | Pool class to which the LU is defined as a member. The dspuLuAdminPoolClassName is valid for pooled LUs only. |
| ROW dspuLuAdminRowStatus | 1.3.6.1.4.1.9.9.24.1.5.1.1.6 | RowStatus | read-create | Used by a Management Station to create or delete the row entry in the dspuLuAdminTable following the RowStatus textual convention. Upon successful creation of the row, an Agent automatically creates a corresponding entry in the dspuLuOperTable. The Management Station can set the value to 'destroy (6)' and the Agent will then delete the rows corresponding to this LU from the dspuLuAdminTable and the dspuLuOperTable. |
| dspuLuAdminTable | 1.3.6.1.4.1.9.9.24.1.5.1 | not-accessible | Table listing all LUs owned by the PU. NOTE: The dspuLuAdminTable does not include LUs owned by default downstream PUs that may be dynamically created. | |
| INT dspuLuAdminType | 1.3.6.1.4.1.9.9.24.1.5.1.1.2 | INTEGER | read-create | LU type is either pooled or dedicated. |
| dspuLuGroup | 1.3.6.1.4.1.9.9.24.2.2.5 | Upstream/Downstream LU information | ||
| dspuLuGroupV11R01 | 1.3.6.1.4.1.9.9.24.2.2.8 | Upstream/Downstream LU information | ||
| dspuLuOperEntry | 1.3.6.1.4.1.9.9.24.1.5.2.1 | not-accessible | Each entry represents a defined LU owned by the PU. | |
| INT dspuLuOperFsmState | 1.3.6.1.4.1.9.9.24.1.5.2.1.7 | INTEGER | read-only | Current FSM state of the LU as follows: reset - neither dnLu or upLu active dnLuStarted - dnLu active, upLu inactive upLuActive - upLu active, dnLu inactive dnLuPendAct - dnLu pending activation, upLu active-unavailable dnLuActUnav - dnLu active-unavailable, upLu active-available upLuPendAvail - upLu pending-available bothAvail - both upLu and dnLu active-available dnLuPendInact - dnLu pending inactive upLuPendInact - upLu pending inactive luInactivityTimeout - inactivity Timeout on LU-to-LU session dnInactivityPendInact - dnLu pending inactive from inactivity timeout |
| INT dspuLuOperLastActivationFailureReason | 1.3.6.1.4.1.9.9.24.1.5.2.1.9 | INTEGER | read-only | Reason for last activation failure of this PU as follows: noError - No LU activation failure has been detected otherError - Undefined error detected during LU activation luNegativeResponse - Negative ACTLU response received from remote LU |
| INT dspuLuOperLuLocalAddress | 1.3.6.1.4.1.9.9.24.1.5.2.1.1 | INTEGER | not-accessible | NAU address of the local LU. |
| INT dspuLuOperPeerLuLocalAddress | 1.3.6.1.4.1.9.9.24.1.5.2.1.5 | INTEGER | read-only | For downstream LUs, the PeerLuLocalAddress identifies the NAU address of the upstream LU to which this downstream LU is assigned. For upstream LUs, the PeerLuLocalAddress identifies the NAU address of the downstream LU to which this upstream LU is assigned. If the PeerLuLocalAddress is zero, the LU is a pooled LU and has not been assigned a peer LU from the pool. |
| I32 dspuLuOperPeerPuIndex | 1.3.6.1.4.1.9.9.24.1.5.2.1.4 | Integer32 | read-only | For downstream LUs, the PeerPuIndex identifies the upstream PU that owns the upstream LU to which this downstream LU is assigned. For upstream LUs, the PeerPuIndex identifies the downstream PU that owns the downstream LU to which this upstream LU is assigned. If PeerPuIndex is zero, the LU is a pooled LU and has not been assigned a peer LU from the pool. |
| STR dspuLuOperPoolClassName | 1.3.6.1.4.1.9.9.24.1.5.2.1.3 | DisplayString | read-only | Pool class to which the LU is defined as a member. The dspuLuOperPoolClassName is valid for pooled LUs only. |
| INT dspuLuOperSessionState | 1.3.6.1.4.1.9.9.24.1.5.2.1.8 | INTEGER | read-only | Operational state of LU session is either bound or unbound. |
| INT dspuLuOperState | 1.3.6.1.4.1.9.9.24.1.5.2.1.6 | INTEGER | read-only | Operational state of LU is either active or inactive. |
| dspuLuOperTable | 1.3.6.1.4.1.9.9.24.1.5.2 | not-accessible | Table listing all LUs owned by the PU. NOTE: In addition to the LUs owned by explicitly defined PUs from the dspuLuAdminTable, the dspuLuOperTable also includes the LUs owned by default downstream PUs that may be dynamically created. | |
| INT dspuLuOperType | 1.3.6.1.4.1.9.9.24.1.5.2.1.2 | INTEGER | read-only | LU type is either pooled or dedicated. |
| NTF dspuLuStateChangeTrap | 1.3.6.1.4.1.9.9.24.1.5.3.1 | Generated when the operational state of the PU changes between activeinactive. The following information is returned: dspuPuOperName -> PU name dspuLuOperLuLocalAddress -> NAU address of LU dspuLuOperState -> Current operational state of the LU | ||
| dspuLuTraps | 1.3.6.1.4.1.9.9.24.1.5.3 | |||
| dspuLuTrapsPrefix | 1.3.6.1.4.1.9.9.24.1.5.3.0 | |||
| dspuNode | 1.3.6.1.4.1.9.9.24.1.1 | |||
| INT dspuNodeActivationWindow | 1.3.6.1.4.1.9.9.24.1.1.9 | INTEGER | read-write | Activation pacing window used by the DSPU node to limit the number of activation RUs sent for a given SAP before waiting for responses from the remote. |
| T/F dspuNodeDefaultPu | 1.3.6.1.4.1.9.9.24.1.1.6 | TruthValue | read-write | Default-PU feature enabled/disabled for the DSPU node. TRUE -> Default-PU feature enabled FALSE -> Default-PU feature disabled |
| INT dspuNodeDefaultPuMaxIframe | 1.3.6.1.4.1.9.9.24.1.1.8 | INTEGER | read-write | Maximum size of an I-frame that can be transmitted/received across the link between the default-PU and a remote PU. |
| INT dspuNodeDefaultPuWindowSize | 1.3.6.1.4.1.9.9.24.1.1.7 | INTEGER | read-write | Send/receive window size to be used across the link between the default-PU and a remote PU. |
| dspuNodeGroup | 1.3.6.1.4.1.9.9.24.2.2.1 | Global DSPU node information | ||
| TIM dspuNodeLastConfigChgTime | 1.3.6.1.4.1.9.9.24.1.1.10 | TimeStamp | read-only | Timestamp of last change to DSPU configuration parameters. LastConfigChgTime reflects any change in DSPU configuration. |
| T/F dspuNodeRsrb | 1.3.6.1.4.1.9.9.24.1.1.1 | TruthValue | read-write | RSRB feature enabled/disabled for the DSPU node. TRUE -> RSRB feature enabled FALSE -> RSRB feature disabled If the RSRB feature is enabled, the following object values must be valid (i.e. non-zero): - dspuNodeRsrbLocalVirtualRing - dspuNodeRsrbBridgeNumber - dspuNodeRsrbTargetVirtualRing - dspuNodeRsrbVirtualMacAddress |
| INT dspuNodeRsrbBridgeNumber | 1.3.6.1.4.1.9.9.24.1.1.3 | INTEGER | read-write | Bridge number connecting the DSPU LocalVirtualRing with the RSRB TargetVirtualRing. Currently, the only valid BridgeNumber supported is 1. BridgeNumber must be one if RSRB is enabled. BridgeNumber is zero if RSRB is not enabled. |
| INT dspuNodeRsrbLocalVirtualRing | 1.3.6.1.4.1.9.9.24.1.1.2 | INTEGER | read-write | Local virtual ring number used by the DSPU node. LocalVirtualRing is zero if RSRB is not enabled. |
| INT dspuNodeRsrbTargetVirtualRing | 1.3.6.1.4.1.9.9.24.1.1.4 | INTEGER | read-write | Target virtual ring number used for RSRB. TargetVirtualRing is zero if RSRB is not enabled. |
| MAC dspuNodeRsrbVirtualMacAddress | 1.3.6.1.4.1.9.9.24.1.1.5 | MacAddress | read-write | Virtual MAC address of the the DSPU node. VirtualMacAddress is zero if RSRB is not enabled. |
| dspuObjects | 1.3.6.1.4.1.9.9.24.1 | |||
| dspuPoolClass | 1.3.6.1.4.1.9.9.24.1.2 | |||
| dspuPoolClassEntry | 1.3.6.1.4.1.9.9.24.1.2.1.1 | not-accessible | Each entry represents a defined pool class. | |
| dspuPoolClassGroup | 1.3.6.1.4.1.9.9.24.2.2.2 | LU pool class information | ||
| INT dspuPoolClassInactivityTimeout | 1.3.6.1.4.1.9.9.24.1.2.1.1.3 | INTEGER | read-write | Value (in minutes) of the inactivity timeout that will be applied to active LU sessions assigned from the pool class. The inactivity timeout feature for pooled LUs is disabled if the InactivityTimeout value is zero. |
| I32 dspuPoolClassIndex | 1.3.6.1.4.1.9.9.24.1.2.1.1.1 | Integer32 | not-accessible | Index of a pool class entry in the dspuPoolClassTable. |
| STR dspuPoolClassName | 1.3.6.1.4.1.9.9.24.1.2.1.1.2 | DisplayString | read-write | Name identifier of the pool class. |
| I32 dspuPoolClassOperDnStreamLuDefs | 1.3.6.1.4.1.9.9.24.1.2.1.1.5 | Integer32 | read-only | Number of downstream LUs defined in the pool class. |
| I32 dspuPoolClassOperUpStreamLuDefs | 1.3.6.1.4.1.9.9.24.1.2.1.1.4 | Integer32 | read-only | Number of upstream LUs defined in the pool class. |
| dspuPoolClassTable | 1.3.6.1.4.1.9.9.24.1.2.1 | not-accessible | Table listing defined pool classes for the DSPU node. A pool class is defined at the DSPU node as a pool of upstream LUs that may be shared among downstream PUs. Each entry in the table represents a separate pool class definition. Entries in the table may not be created/deleted; however, values in existing entries may be modified. Pool classes are created when an existing LU is defined as a member of the pool class. | |
| dspuPooledLu | 1.3.6.1.4.1.9.9.24.1.3 | |||
| dspuPooledLuEntry | 1.3.6.1.4.1.9.9.24.1.3.1.1 | not-accessible | Each entry represents an LU that is defined as a member of the specified pool class. | |
| dspuPooledLuGroup | 1.3.6.1.4.1.9.9.24.2.2.3 | Pooled LU information | ||
| INT dspuPooledLuPeerLuLocalAddress | 1.3.6.1.4.1.9.9.24.1.3.1.1.2 | INTEGER | read-only | NAU address (dspuLuOperLuLocalAddress) of the peer LU. PeerLuLocalAddress is zero if peer LU has not been assigned. |
| I32 dspuPooledLuPeerPuIndex | 1.3.6.1.4.1.9.9.24.1.3.1.1.1 | Integer32 | read-only | Index (dspuPuOperIndex) of the peer PU that owns the peer LU. PeerPuIndex is zero if peer LU has not been assigned. |
| dspuPooledLuTable | 1.3.6.1.4.1.9.9.24.1.3.1 | not-accessible | Table listing all LUs defined in a specified pool class. The entries in the table provide information such that the downstream LUs in the pool can be correlated with the upstream LUs to which they may be assigned and vice versa. If all upstream LUs have been assigned, downstream LUs may be waiting for assignment. If there are no downstream LUs waiting for assignment, upstream LUs may be unassigned. | |
| dspuPu | 1.3.6.1.4.1.9.9.24.1.4 | |||
| NTF dspuPuActivationFailureTrap | 1.3.6.1.4.1.9.9.24.1.4.4.2 | Generated whenever a PU activation failure is detected. The following information is returned: dspuPuOperName -> PU name dspuPuOperState -> Current operational state of the PU dspuPuStatsLastActivationFailureReason -> Reason for PU activation failure | ||
| INT dspuPuAdminDlcPort | 1.3.6.1.4.1.9.9.24.1.4.1.1.16 | INTEGER | read-create | DLC port used by the dspuNode for link activation with the remote PU. |
| INT dspuPuAdminDlcType | 1.3.6.1.4.1.9.9.24.1.4.1.1.14 | INTEGER | read-create | DLC type used by the dspuNode for link activation with the remote PU. |
| INT dspuPuAdminDlcUnit | 1.3.6.1.4.1.9.9.24.1.4.1.1.15 | INTEGER | read-create | DLC unit used by the dspuNode for link activation with the remote PU. |
| dspuPuAdminEntry | 1.3.6.1.4.1.9.9.24.1.4.1.1 | not-accessible | Each entry represents a defined upstream/downstream PU. | |
| T/F dspuPuAdminFocalPoint | 1.3.6.1.4.1.9.9.24.1.4.1.1.17 | TruthValue | read-create | PU serves as a focal point for alert forwarding. TRUE -> PU serves as focal point FALSE -> PU does not serve as focal point Only an upstream PU may be defined as a focal point. Downstream PUs can never be defined as a focal point; FocalPoint is always FALSE for downstream PUs. The DSPU node may define only one upstream PU as a focal point PU. |
| I32 dspuPuAdminIndex | 1.3.6.1.4.1.9.9.24.1.4.1.1.1 | Integer32 | not-accessible | Index of the PU entry in the dspuPuAdminTable. |
| INT dspuPuAdminLinkRetryCount | 1.3.6.1.4.1.9.9.24.1.4.1.1.11 | INTEGER | read-create | Number of times that the DSPU node will attempt to activate the link between the dspuNode and the remote PU. |
| INT dspuPuAdminLinkRetryTimeout | 1.3.6.1.4.1.9.9.24.1.4.1.1.12 | INTEGER | read-create | Value (in seconds) for the delay between link activation attempts between the dspuNode and the remote PU. |
| INT dspuPuAdminLocalSapAddress | 1.3.6.1.4.1.9.9.24.1.4.1.1.6 | INTEGER | read-create | SAP address of the local PU. |
| INT dspuPuAdminMaxIframe | 1.3.6.1.4.1.9.9.24.1.4.1.1.10 | INTEGER | read-create | Maximum size of an I-frame that can be transmitted/received across the link between this dspuNode and the remote PU. |
| STR dspuPuAdminName | 1.3.6.1.4.1.9.9.24.1.4.1.1.2 | DisplayString | read-create | Name of the PU. |
| STR dspuPuAdminRemoteAddress | 1.3.6.1.4.1.9.9.24.1.4.1.1.19 | DisplayString | read-create | Poll address, DLCI, or subscriber address associated with the remote PU. |
| MAC dspuPuAdminRemoteMacAddress | 1.3.6.1.4.1.9.9.24.1.4.1.1.4 | MacAddress | read-create | MAC address of the remote PU. |
| INT dspuPuAdminRemoteSapAddress | 1.3.6.1.4.1.9.9.24.1.4.1.1.5 | INTEGER | read-create | SAP address of the remote PU. |
| ROW dspuPuAdminRowStatus | 1.3.6.1.4.1.9.9.24.1.4.1.1.18 | RowStatus | read-create | Used by a Management Station to create or delete the row entry in the dspuPuAdminTable following the RowStatus textual convention. Upon successful creation of the row, an Agent automatically creates a corresponding entry in the dspuPuOperTable. The Management Station can set the value to 'destroy (6)' and the Agent will then delete the rows corresponding to this PU from the dspuPuAdminTable and dspuPuOperTable. |
| T/F dspuPuAdminStartPu | 1.3.6.1.4.1.9.9.24.1.4.1.1.13 | TruthValue | read-create | Attempt link activation with the remote PU. TRUE -> Attempt link activation with remote PU. FALSE -> Do not attempt link activation with remote PU. |
| dspuPuAdminTable | 1.3.6.1.4.1.9.9.24.1.4.1 | not-accessible | Table listing all defined upstream/downstream PUs that are owned by the DSPU node. NOTE: The dspuPuAdminTable does not include default downstream PUs that may be dynamically created. | |
| INT dspuPuAdminType | 1.3.6.1.4.1.9.9.24.1.4.1.1.3 | INTEGER | read-create | PU Type is either upstream or downstream. |
| INT dspuPuAdminWindowSize | 1.3.6.1.4.1.9.9.24.1.4.1.1.9 | INTEGER | read-create | Send/Receive window size to be used across the link between this dspuNode and the remote PU. |
| I32 dspuPuAdminXid | 1.3.6.1.4.1.9.9.24.1.4.1.1.7 | Integer32 | read-create | Upstream PU : XID that will be sent to the remote PU. Dnstream PU : XID that must be received from the remote PU. |
| INT dspuPuAdminXidFmt | 1.3.6.1.4.1.9.9.24.1.4.1.1.8 | INTEGER | read-create | Type of XID format used during activation of the link between this dspuNode and the remote PU. |
| dspuPuGroup | 1.3.6.1.4.1.9.9.24.2.2.4 | Upstream/Downstream PU node information | ||
| dspuPuGroupV11R01 | 1.3.6.1.4.1.9.9.24.2.2.7 | Upstream/Downstream PU node information | ||
| INT dspuPuOperDlcPort | 1.3.6.1.4.1.9.9.24.1.4.2.1.16 | INTEGER | read-only | DLC port used by the dspuNode for link activation with the remote PU. |
| INT dspuPuOperDlcType | 1.3.6.1.4.1.9.9.24.1.4.2.1.14 | INTEGER | read-only | DLC type used by the dspuNode for link activation with the remote PU. |
| INT dspuPuOperDlcUnit | 1.3.6.1.4.1.9.9.24.1.4.2.1.15 | INTEGER | read-only | DLC unit used by the dspuNode for link activation with the remote PU. |
| dspuPuOperEntry | 1.3.6.1.4.1.9.9.24.1.4.2.1 | not-accessible | Each entry represents an active upstream/downstream PU. | |
| T/F dspuPuOperFocalPoint | 1.3.6.1.4.1.9.9.24.1.4.2.1.17 | TruthValue | read-only | PU serves as a focal point for alert forwarding. TRUE -> PU serves as focal point FALSE -> PU does not serve as focal point Only an upstream PU may be defined as a focal point. Downstream PUs can never be defined as a focal point; FocalPoint is always FALSE for downstream PUs. The DSPU node may define only one upstream PU as a focal point PU. |
| INT dspuPuOperFsmState | 1.3.6.1.4.1.9.9.24.1.4.2.1.19 | INTEGER | read-only | Current FSM state of the PU as follows: linkReset - Link is in reset state - not connected linkPendConnOut - Pending ConnectOut to establish link linkPendConnIn - Pending ConnectIn to establish link linkPendXid - Pending XID negotiation on the link linkXidNeg - XID negotiation proceeding on link linkConnOut - ConnectOut link activation linkConnIn - ConnectIn link activation linkConnected - Link connected, PU inactive puPendAct - Link connected, PU pending activation puActive - Link connected, PU active puBusy - Link connected, PU busy puPendInact - Link connected, PU pending deactivation linkPendDisc - Pending disconnect of link linkPendClose - Pending close of link station |
| I32 dspuPuOperIndex | 1.3.6.1.4.1.9.9.24.1.4.2.1.1 | Integer32 | not-accessible | Index of the PU entry in dspuPuOperTable. |
| TIM dspuPuOperLastStateChgTime | 1.3.6.1.4.1.9.9.24.1.4.2.1.21 | TimeStamp | read-only | TimeStamp of last PU state change between activeinactive. |
| INT dspuPuOperLinkRetryCount | 1.3.6.1.4.1.9.9.24.1.4.2.1.11 | INTEGER | read-only | Number of times that the DSPU node will attempt to activate the link between the dspuNode and the remote PU. |
| INT dspuPuOperLinkRetryTimeout | 1.3.6.1.4.1.9.9.24.1.4.2.1.12 | INTEGER | read-only | Value (in seconds) for the delay between link activation attempts between the dspuNode and the remote PU. |
| INT dspuPuOperLocalSapAddress | 1.3.6.1.4.1.9.9.24.1.4.2.1.6 | INTEGER | read-only | SAP address of the local PU. |
| INT dspuPuOperMaxIframe | 1.3.6.1.4.1.9.9.24.1.4.2.1.10 | INTEGER | read-only | Maximum size of an I-frame that can be transmitted/received across the link between this dspuNode and the remote PU. |
| STR dspuPuOperName | 1.3.6.1.4.1.9.9.24.1.4.2.1.2 | DisplayString | read-only | Name of the PU. |
| STR dspuPuOperRemoteAddress | 1.3.6.1.4.1.9.9.24.1.4.2.1.22 | DisplayString | read-only | Poll address, DLCI, or subscriber address associated with the remote PU. |
| MAC dspuPuOperRemoteMacAddress | 1.3.6.1.4.1.9.9.24.1.4.2.1.4 | MacAddress | read-only | MAC address of the remote PU. |
| INT dspuPuOperRemoteSapAddress | 1.3.6.1.4.1.9.9.24.1.4.2.1.5 | INTEGER | read-only | SAP address of the remote PU. |
| T/F dspuPuOperStartPu | 1.3.6.1.4.1.9.9.24.1.4.2.1.13 | TruthValue | read-only | Attempt link activation with the remote PU. TRUE -> Attempt link activation with remote PU. FALSE -> Do not attempt link activation with remote PU. |
| TIM dspuPuOperStartTime | 1.3.6.1.4.1.9.9.24.1.4.2.1.20 | TimeStamp | read-only | Timestamp of PU activation (when ACTPU +rsp received). |
| INT dspuPuOperState | 1.3.6.1.4.1.9.9.24.1.4.2.1.18 | INTEGER | read-only | Operational state of PU is either active or inactive. |
| dspuPuOperTable | 1.3.6.1.4.1.9.9.24.1.4.2 | not-accessible | Table listing all active upstream/downstream PUs that are owned by the DSPU node (including default PUs). NOTE: In addition to the explicitly defined PUs from the dspuPuAdminTable, the dspuPuOperTable also includes default downstream PUs that may be dynamically created. | |
| INT dspuPuOperType | 1.3.6.1.4.1.9.9.24.1.4.2.1.3 | INTEGER | read-only | PU type is either upstream or downstream. |
| INT dspuPuOperWindowSize | 1.3.6.1.4.1.9.9.24.1.4.2.1.9 | INTEGER | read-only | Send/Receive window size to be used across the link between this dspuNode and the remote PU. |
| I32 dspuPuOperXid | 1.3.6.1.4.1.9.9.24.1.4.2.1.7 | Integer32 | read-only | Upstream PU : XID that was sent to the remote PU. Dnstream PU : XID that was received from the remote PU. |
| INT dspuPuOperXidFmt | 1.3.6.1.4.1.9.9.24.1.4.2.1.8 | INTEGER | read-only | Type of XID format used during activation of the link between this dspuNode and the remote PU. |
| NTF dspuPuStateChangeTrap | 1.3.6.1.4.1.9.9.24.1.4.4.1 | Generated when the operational state of the PU changes between activeinactive. The following information is returned: dspuPuOperName -> PU name dspuPuOperState -> Current operational state of the PU | ||
| C32 dspuPuStatsActivationFailures | 1.3.6.1.4.1.9.9.24.1.4.3.1.10 | Counter32 | read-only | Number of activation failures for this PU. |
| C32 dspuPuStatsActiveLus | 1.3.6.1.4.1.9.9.24.1.4.3.1.7 | Counter32 | read-only | Number of active LUs on this PU (LU becomes active when ACTLU +rsp received). |
| C32 dspuPuStatsBindLus | 1.3.6.1.4.1.9.9.24.1.4.3.1.9 | Counter32 | read-only | Number of LUs on this PU which are active-in-session. (LU is active-in-session when BIND rq received) |
| dspuPuStatsEntry | 1.3.6.1.4.1.9.9.24.1.4.3.1 | not-accessible | Each entry represents an active upstream/downstream PU and has a corresponding entry in the dspuPuOperTable. | |
| C32 dspuPuStatsInactiveLus | 1.3.6.1.4.1.9.9.24.1.4.3.1.8 | Counter32 | read-only | Number of inactive LUs on this PU (LU is inactive until ACTLU rq or ACTLU +rsp received). |
| INT dspuPuStatsLastActivationFailureReason | 1.3.6.1.4.1.9.9.24.1.4.3.1.11 | INTEGER | read-only | Reason for last activation failure of this PU as follows: noError - No PU activation failure has been detected otherError - Undefined error detected during PU activation internalError - Internal resources error detected during PU activation configurationError - PU configuration error - PU could not be activated puNegativeResponse - Negative ACTPU response received from remote PU puAlreadyActive - PU is already active |
| C32 dspuPuStatsRcvdBytes | 1.3.6.1.4.1.9.9.24.1.4.3.1.2 | Counter32 | read-only | Number of bytes received by this PU. |
| C32 dspuPuStatsRcvdFrames | 1.3.6.1.4.1.9.9.24.1.4.3.1.4 | Counter32 | read-only | Number of frames received by this PU. |
| C32 dspuPuStatsRcvdNegativeRsps | 1.3.6.1.4.1.9.9.24.1.4.3.1.6 | Counter32 | read-only | Number of negative responses received by this PU. |
| C32 dspuPuStatsSentBytesEx | 1.3.6.1.4.1.9.9.24.1.4.3.1.1 | Counter32 | read-only | Number of bytes sent by this PU. |
| C32 dspuPuStatsSentFrames | 1.3.6.1.4.1.9.9.24.1.4.3.1.3 | Counter32 | read-only | Number of frames sent by this PU. |
| C32 dspuPuStatsSentNegativeRsps | 1.3.6.1.4.1.9.9.24.1.4.3.1.5 | Counter32 | read-only | Number of negative responses sent by this PU. |
| dspuPuStatsTable | 1.3.6.1.4.1.9.9.24.1.4.3 | not-accessible | Table listing the statistics recorded for each PU. | |
| dspuPuTraps | 1.3.6.1.4.1.9.9.24.1.4.4 | |||
| dspuPuTrapsPrefix | 1.3.6.1.4.1.9.9.24.1.4.4.0 | |||
| dspuSap | 1.3.6.1.4.1.9.9.24.1.6 | |||
| INT dspuSapAddress | 1.3.6.1.4.1.9.9.24.1.6.1.1.1 | INTEGER | not-accessible | SAP address of the local SAP. |
| INT dspuSapDlcPort | 1.3.6.1.4.1.9.9.24.1.6.1.1.5 | INTEGER | not-accessible | DLC port of the adapter that owns the local SAP. |
| INT dspuSapDlcType | 1.3.6.1.4.1.9.9.24.1.6.1.1.3 | INTEGER | not-accessible | DLC type of the adapter that owns the local SAP. |
| INT dspuSapDlcUnit | 1.3.6.1.4.1.9.9.24.1.6.1.1.4 | INTEGER | not-accessible | DLC unit of the adapter that owns the local SAP. |
| dspuSapEntry | 1.3.6.1.4.1.9.9.24.1.6.1.1 | not-accessible | Each entry represents an enabled SAP for the DSPU node. | |
| dspuSapGroup | 1.3.6.1.4.1.9.9.24.2.2.6 | Local SAP information | ||
| INT dspuSapOperState | 1.3.6.1.4.1.9.9.24.1.6.1.1.6 | INTEGER | read-only | Operational state of the local SAP as follows: - sapClosed - sapOpening - sapOpened - sapClosing |
| ROW dspuSapRowStatus | 1.3.6.1.4.1.9.9.24.1.6.1.1.7 | RowStatus | read-create | This object is used by a Management Station to create or delete the row entry in the dspuSapTable following the RowStatus textual convention. The Management Station can set the value to 'destroy (6)' and the Agent will then delete the rows corresponding to this SAP from the dspuSapTable. The local SAP address is enabled on the specified adapter when a row entry in the dspuSapTable is created. |
| NTF dspuSapStateChangeTrap | 1.3.6.1.4.1.9.9.24.1.6.2.1 | Generated when the operational state of the SAP changes between 'open' or 'closed'. The following information is returned: dspuSapOperDlcType -> DLC type of the adapter on which SAP is located dspuSapOperDlcUnit -> Unit ID of the adapter on which SAP is located dspuSapOperDlcPort -> Port ID of the adapter on which SAP is located dspuSapOperAddress -> SAP address dspuSapOperState -> Current operational state of the SAP | ||
| dspuSapTable | 1.3.6.1.4.1.9.9.24.1.6.1 | not-accessible | Table listing the SAPs that are enabled for the DSPU node. | |
| dspuSapTraps | 1.3.6.1.4.1.9.9.24.1.6.2 | |||
| INT dspuSapType | 1.3.6.1.4.1.9.9.24.1.6.1.1.2 | INTEGER | read-create | Local SAP type is either upstreamSap or downstreamSap. |
| NTF newdspuLuStateChangeTrap | 1.3.6.1.4.1.9.9.24.1.5.3.0.1 | Generated when the operational state of the LU changes between activeinactive. The following information is returned: dspuPuOperName -> PU name dspuLuOperState -> Current operational state of the LU | ||
| NTF newdspuPuActivationFailureTrap | 1.3.6.1.4.1.9.9.24.1.4.4.0.2 | Generated whenever a PU activation failure is detected. The following information is returned: dspuPuOperName -> PU name dspuPuOperState -> Current operational state of the PU dspuPuStatsLastActivationFailureReason -> Reason for PU activation failure | ||
| NTF newdspuPuStateChangeTrap | 1.3.6.1.4.1.9.9.24.1.4.4.0.1 | Generated when the operational state of the PU changes between activeinactive. The following information is returned: dspuPuOperName -> PU name dspuPuOperState -> Current operational state of the PU |
RFC description
Manages Cisco Downstream Physical Unit (DSPU) SNA connectivity, enabling IBM cluster controller emulation over IP networks.
Start monitoring Cisco routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.