All MIBs › CISCO-CAS-IF-EXT-MIB › ccasRSSeqInfCollect
ccasRSSeqInfCollect
Module: CISCO-CAS-IF-EXT-MIB
OID (symbolic): CISCO-CAS-IF-EXT-MIB::ccasRSSeqInfCollect
OID (numeric): 1.3.6.1.4.1.9.9.314.1.4.1.1.65
Node type: OBJECT-TYPE
Type: SnmpAdminString
Access: read-write
Description: This object determines the sequence in which information will be gathered by the incoming register.
Only a set of predefined characters can be used in the octet string notation of the sequence. The special character and the alphabet strings allowed are listed below:
'/' - Separator between different elements of information that should be collected. - Indicates how many digits of the following information element should be collected before switching to collecting the next information element. Number always precedes one of the information elements such as D or A. If no number is specified, all of the digits for that information element are collected before fetching digits for next info element.
di - DNIS/Destination number/dialed number/called number. si - ANIS/Source number/calling number. sc - Subscriber Category. cc - Country Code. es - Echo Suppression Information. noc - Nature of Circuit. disc - Discriminator Digit. The default value is country specific.
What is ccasRSSeqInfCollect?
This object holds a specially formatted string, built from a small set of predefined characters, that defines the order and quantity of information, such as ANI, DNIS, or category digits, an R2 incoming register should collect, with a slash separating each element to be gathered. This is essentially a configuration recipe for register signaling; getting the sequence or digit-count syntax wrong causes the register to request information elements in the wrong order or expect the wrong number of digits, which desynchronizes call setup on that trunk from what the far end's R2 variant expects. A sequence string that schematically reads like '3ANI/DNIS' would tell the register to collect three ANI digits before moving on to DNIS collection, mirroring the order used by that country's R2 practice.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.314.1.4.1.1.65 snmpwalk -v2c -c public <target> CISCO-CAS-IF-EXT-MIB::ccasRSSeqInfCollect
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.314.1.4.1.1.65.1 snmpget -v2c -c public <target> CISCO-CAS-IF-EXT-MIB::ccasRSSeqInfCollect.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.314.1.4.1.1.65.1 s <value>
SNMPv3 example:
snmpget -v3 -l authPriv -u snmpv3-user -a SHA -A "AuthPassword1" -x AES -X "PrivPassword1" <target> ccasRSSeqInfCollect.1
Start monitoring Cisco media gateways / voice gateway routers with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-CAS-IF-EXT-MIB::ccasRSSeqInfCollect OID value, configure state conditions and alerts, and monitor any Cisco media gateways / voice gateway routers from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.314 | ciscoCasIfExtMIB | CISCO-CAS-IF-EXT-MIB |
| 1.3.6.1.4.1.9.9.314.1 | ciscoCasIfExtMIBObjects | CISCO-CAS-IF-EXT-MIB |
| 1.3.6.1.4.1.9.9.314.1.4 | ccasIfExtConfigRegisterSignal | CISCO-CAS-IF-EXT-MIB |
| 1.3.6.1.4.1.9.9.314.1.4.1 | ccasIfExtRegisterSignalTable | CISCO-CAS-IF-EXT-MIB |
| 1.3.6.1.4.1.9.9.314.1.4.1.1 | ccasIfExtRegisterSignalEntry | CISCO-CAS-IF-EXT-MIB |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.65 | ccasRSSeqInfCollect | CISCO-CAS-IF-EXT-MIB |