C-PRODUCT-SIM-STAT-MIB

All MIBs › C-PRODUCT-SIM-STAT-MIB

Category: WAN

Description: Provides statistics counters for serial interface modules on C-PRODUCT equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is C-PRODUCT-SIM-STAT-MIB?

C-PRODUCT-SIM-STAT-MIB is a vendor MIB that provides traffic and error statistics for Serial Interface Modules (SIM) and associated ATM virtual circuits on the described equipment. It exposes per-port frame/octet counters for received and transmitted traffic, invalid- and congested-frame counts, FCS error counts, and a command object to clear accumulated statistics, plus a separate table for ATM VC-level statistics. This is a clear performance/fault-monitoring MIB: comparing simPortRxFcsErrs and simPortInvalidFrames against simPortRxFrames reveals a degrading physical link or cabling problem, while simPortCongestedFrames indicates the port is experiencing buffer congestion under load. It has no apparent dependency on external standard MIBs, appearing to be a self-contained vendor statistics module. It is deployed on serial/ATM access equipment used for WAN interface aggregation, and the C-PRODUCT-SIM-STAT-MIB MIB is commonly loaded into a MIB browser to poll these counters directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in C-PRODUCT-SIM-STAT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

serial/ATM WAN access equipment

Monitoring Examples

An administrator would poll simPortRxFrames/simPortTxFrames and simPortRxOctets/simPortTxOctets in simPortStatTable to baseline normal traffic levels on a serial port, then watch simPortRxFcsErrs and simPortInvalidFrames for signs of a failing cable or clocking mismatch. A rising simPortCongestedFrames count would indicate the port's buffers are being overrun, a possible precursor to dropped traffic. simPortClrStatCmd and simPortClrStatTime would be used to reset counters after a fix and record when the last reset occurred, while simNewAtmVcStatTable would be checked for equivalent statistics on individual ATM virtual circuits.

What Can Be Monitored

received/transmitted frame and octet counts
invalid frame count
congested frame count
FCS error count
ATM VC-level statistics
statistics clear time/command

Imported Objects

From C-PRODUCT-BASE-MIB

TimeAndDate
portNumber	OBJECT-TYPE
portSlot	OBJECT-TYPE
vcpSideId	OBJECT-TYPE

From C-PRODUCT-GROUP-MIB

qsim	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

OIDs

OID symbolic	OID numeric	Type	Access	Description
simAtmVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.2
simDxiVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.3
simFrameRelayVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.4
INT simLmiClrStatCmd	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.1	INTEGER	read-write	This is a command to clear all LMI statistics. This object applies when LMI protocol is not 'none'.
TIM simLmiClrStatTime	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.2	TimeAndDate	read-only	The time when the last LMI statistics was cleared. This object applies when LMI protocol is not 'none'.
CTR simLmiDiscardedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.4	Counter	read-only	Discarded LMI frames. This object applies when LMI protocol is not 'none'.
CTR simLmiNetworkLossSeqNumSyncs	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.17	Counter	read-only	Network-side loss of sequence number synchronization. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiNetworkPvTimeouts	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.12	Counter	read-only	Network-side PV timeouts. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiNetworkRcvFullStatusRequests	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.15	Counter	read-only	Network-side full status requests. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiNetworkRcvLivRequests	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.13	Counter	read-only	Network-side LIV requests. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiNetworkXmtFullStatusResponses	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.16	Counter	read-only	Network-side full status responses. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiNetworkXmtLivResponses	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.14	Counter	read-only	Network-side LIV responses. This object applies when LMI procedure is network-side or bidirectional.
CTR simLmiReceivedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.3	Counter	read-only	Received LMI frames. This object applies when LMI protocol is not 'none'.
simLmiStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5
simLmiStatEntry	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1		not-accessible	LMI statistics entry. The slot index (portSlot) of this entry can be from 4 to 6. The port index (portNumber) can be from 1 to 8 for FAM, 1 to 4 for QSIM and 1 for HSIM.
simLmiStatTable	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1		not-accessible	LMI statistics table.
CTR simLmiUserLivTimeouts	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.5	Counter	read-only	User-side LIV timeouts. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserLossSeqNumSyncs	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.10	Counter	read-only	User-side loss of sequence number synchronization. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserRcvFullStatusResponses	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.9	Counter	read-only	User-side full status responses. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserRcvLivResponses	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.7	Counter	read-only	User-side LIV responses. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserRcvUnconfigPvcs	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.11	Counter	read-only	User-side unconfigured PVCs. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserXmtFullStatusRequests	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.8	Counter	read-only	User-side full status requests. This object applies when LMI procedure is user-side or bidirectional.
CTR simLmiUserXmtLivRequests	1.3.6.1.4.1.43.1.12.3.1.1.12.5.5.1.1.6	Counter	read-only	User-side LIV requests. This object applies when LMI procedure is user-side or bidirectional.
INT simNewAtmVcClrStatCmd	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.1	INTEGER	read-write	This is issued to clear all statistics of this ATM VC. The current time will be stored at simNewAtmVcClrStatTime.
TIM simNewAtmVcClrStatTime	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.2	TimeAndDate	read-only	The time when the last statistics was clear.
CTR simNewAtmVcCongestedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.6	Counter	read-only	Total congested frames at this ATM VC since last counter reset. These frames were not transmitted due to link congestion.
CTR simNewAtmVcInvalidFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.5	Counter	read-only	Total received invalid frames at this ATM VC since last counter reset. These frames are received with good VC id but can not be processed due to wrong content.
CTR simNewAtmVcRxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.3	Counter	read-only	Total received frames at this ATM VC since last counter reset.
simNewAtmVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6
simNewAtmVcStatEntry	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1		not-accessible	Information about a Serial Interface Module ATM VC Statistics. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4 for QSIM, 1 for HSIM, and from 1 to 8 for OSIM.
simNewAtmVcStatTable	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1		not-accessible	The Serial Interface Module ATM VC Statistics table.
CTR simNewAtmVcTxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.6.1.1.4	Counter	read-only	Total transmitted frames at this ATM VC since last counter reset. These frames were transmitted successfuly.
INT simNewDxiVcClrStatCmd	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.1	INTEGER	read-write	This is issued to clear all statistics of this DXI VC. The current time will be stored at simDxiVcClrStatTime.
TIM simNewDxiVcClrStatTime	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.2	TimeAndDate	read-only	The time when the last statistics was clear.
CTR simNewDxiVcCongestedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.6	Counter	read-only	Total congested frames at this DXI VC since last counter reset. These frames were not transmitted due to link congestion.
CTR simNewDxiVcInvalidFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.5	Counter	read-only	Total received invalid frames at this DXI VC since last counter reset. These frames are received with good VC id but can not be processed due to wrong content.
CTR simNewDxiVcRxClp	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.9	Counter	read-only	Total received frames with CLP bit set at this DXI VC since last counter reset.
CTR simNewDxiVcRxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.3	Counter	read-only	Total received frames at this DXI VC since last counter reset.
CTR simNewDxiVcRxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.7	Counter	read-only	Total received octets at this DXI VC since last counter reset.
simNewDxiVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7
simNewDxiVcStatEntry	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1		not-accessible	Information about a Serial Interface Module DXI VC Statistics. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4 for QSIM, 1 for HSIM, and from 1 to 8 for OSIM.
simNewDxiVcStatTable	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1		not-accessible	The Serial Interface Module DXI VC Statistics table.
CTR simNewDxiVcTxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.4	Counter	read-only	Total transmitted frames at this DXI VC since last counter reset. These frames were transmitted successfuly.
CTR simNewDxiVcTxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.7.1.1.8	Counter	read-only	Total transmitted octets at this DXI VC since last counter reset.
INT simNewFrameRelayVcClrStatCmd	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.1	INTEGER	read-write	This is issued to clear all statistics of this FR VC. The current time will be stored at simNewFrameRelayVcClrStatTime.
TIM simNewFrameRelayVcClrStatTime	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.2	TimeAndDate	read-only	The time when the last statistics was clear.
CTR simNewFrameRelayVcCongestedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.6	Counter	read-only	Total congested frames at this FR VC since last counter reset. These frames were not transmitted due to link congestion.
CTR simNewFrameRelayVcInvalidFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.5	Counter	read-only	Total received invalid frames at this FR VC since last counter reset. These frames are received with good VC id but can not be processed due to wrong content.
CTR simNewFrameRelayVcRxBecn	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.11	Counter	read-only	Total received frames with BECN bit set at this FR VC since last counter reset.
CTR simNewFrameRelayVcRxDe	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.9	Counter	read-only	Total received frames with DE bit set at this FR VC since last counter reset.
CTR simNewFrameRelayVcRxFecn	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.10	Counter	read-only	Total received frames with FECN bit set at this FR VC since last counter reset.
CTR simNewFrameRelayVcRxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.3	Counter	read-only	Total received frames at this FR VC since last counter reset.
CTR simNewFrameRelayVcRxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.7	Counter	read-only	Total received octets at this FR VC since last counter reset.
simNewFrameRelayVcStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8
simNewFrameRelayVcStatEntry	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1		not-accessible	Information about a Serial Interface Module FR VC Statistics. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4 for QSIM, 1 for HSIM, and from 1 to 8 for OSIM.
simNewFrameRelayVcStatTable	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1		not-accessible	The Serial Interface Module FR VC Statistics table.
CTR simNewFrameRelayVcTxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.4	Counter	read-only	Total transmitted frames at this FR VC since last counter reset. These frames were transmitted successfuly.
CTR simNewFrameRelayVcTxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.8.1.1.8	Counter	read-only	Total transmitted octets at this FR VC since last counter reset.
INT simPortClrStatCmd	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.1	INTEGER	read-write	This is issued to clear all statistics of this port. The current time will be stored at simPortClrStatTime.
TIM simPortClrStatTime	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.2	TimeAndDate	read-only	The time when the last statistics was clear.
CTR simPortCongestedFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.6	Counter	read-only	Total congested frames at this port since last counter reset. These frames were not transmitted due to link congestion.
CTR simPortInvalidFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.5	Counter	read-only	Total received invalid frames at this port since last counter reset. These frames are received with good FCS but can not be processed due to wrong content.
CTR simPortRxFcsErrs	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.9	Counter	read-only	Total received frames with bad FCS at this port since last counter reset.
CTR simPortRxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.3	Counter	read-only	Total received frames with good FCS at this port since last counter reset.
CTR simPortRxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.7	Counter	read-only	Total received octets with good FCS at this port since last counter reset.
simPortStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1
simPortStatEntry	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1		not-accessible	Information about a Serial Interface Module Port Statistics. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4 for QSIM, 1 for HSIM, and from 1 to 8 for OSIM.
simPortStatTable	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1		not-accessible	The Serial Interface Module Port Statistics table.
CTR simPortTxFrames	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.4	Counter	read-only	Total transmitted frames at this port since last counter reset. These frames were transmitted successfuly.
CTR simPortTxOctets	1.3.6.1.4.1.43.1.12.3.1.1.12.5.1.1.1.8	Counter	read-only	Total transmitted octets at this port since last counter reset.
simStat	1.3.6.1.4.1.43.1.12.3.1.1.12.5

RFC description

Provides statistics for Serial Interface Modules (QSIM, HSIM, OSIM) including port, ATM VC, and frame relay statistics.

Start monitoring Networking equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download C-PRODUCT-SIM-STAT-MIB

What Is C-PRODUCT-SIM-STAT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description