C-PRODUCT-BASE-MIB

All MIBs › C-PRODUCT-BASE-MIB

Category: Hardware Inventory

Description: Provides the base system management objects shared across C-PRODUCT series equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is C-PRODUCT-BASE-MIB?

C-PRODUCT-BASE-MIB is a vendor base MIB providing the common system management objects shared across a "C-PRODUCT" line of WAN access/switching equipment (its sibling HSSI and OC3 MIBs suggest ATM/WAN access platforms). It exposes general system identity and site information (shelf name, customer name, location, maintenance contact), local management access configuration (auto-logout timer, password, SNMP community and IP/subnet for the local host), current firmware release, and system date/time. Its monitoring value is chiefly configuration/software status: confirming the running sysGenCurrentCodeRelease across a fleet of shelves, verifying management access settings (community strings, IP config) are correct, and tracking sysTimeAndDate for accurate event correlation, alongside basic site-identification data useful when triaging a shelf-level alarm. It is a self-contained vendor base MIB that other C-PRODUCT feature MIBs (HSSI, OC3) build upon rather than depending on external standards. Deployment context is carrier or enterprise WAN access shelves/chassis where multiple interface-specific MIBs share this common system identity and management layer, and loading the module into a C-PRODUCT-BASE-MIB MIB Browser session surfaces the shelf identity, management-access, and firmware-release objects described above as the primary pollable leaves.

IPNetwork Monitor allows you to monitor SNMP objects defined in C-PRODUCT-BASE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

C-PRODUCT series WAN access/ATM shelf or chassis

Monitoring Examples

An operator would poll sysGenCurrentCodeRelease across all shelves to confirm firmware consistency before a maintenance window, and check sysGenInfoLocation/sysGenInfoMaintenanceContact when an alarm fires to quickly identify the physical site and contact. Verifying sysIpConfigLocalHostIpAddress and sysIpConfigLocalHostCommunityName ensures the shelf is still reachable via its expected management IP and SNMP community. A mismatch between sysTimeAndDate and NTP-synced time would explain skewed alarm timestamps during troubleshooting.

What Can Be Monitored

current firmware/code release
shelf/site identification and contact info
management IP address and SNMP community
system date/time
auto-logout timer configuration

Imported Objects

From C-PRODUCT-GROUP-MIB

card	OBJECT-IDENTITY
circuit	OBJECT-IDENTITY
fault	OBJECT-IDENTITY
port	OBJECT-IDENTITY
shelf	OBJECT-IDENTITY
sys	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
sysGenInfo	1.3.6.1.4.1.43.1.12.3.1.1.1.1
STR sysGenInfoShelfName	1.3.6.1.4.1.43.1.12.3.1.1.1.1.1	DisplayString	read-write	Name of the managed node.
STR sysGenInfoCustomerName	1.3.6.1.4.1.43.1.12.3.1.1.1.1.2	DisplayString	read-write	Name of the organization that uses the managed node.
STR sysGenInfoPhoneNumber	1.3.6.1.4.1.43.1.12.3.1.1.1.1.3	DisplayString	read-write	Phone number of the organization that uses the managed node.
STR sysGenInfoMaintenanceContact	1.3.6.1.4.1.43.1.12.3.1.1.1.1.4	DisplayString	read-write	Maintenance contact of the managed node.
STR sysGenInfoLocation	1.3.6.1.4.1.43.1.12.3.1.1.1.1.5	DisplayString	read-write	Location of the managed node.
INT sysGenInfoAutoLogoutTime	1.3.6.1.4.1.43.1.12.3.1.1.1.1.6	INTEGER	read-write	The time a TELNET or VT-100 terminal user can maintain a session with the managed node without any keyboard action. Unit: minute
OCT sysGenInfoPassword	1.3.6.1.4.1.43.1.12.3.1.1.1.1.7	OCTET STRING	read-write	Password required to access the managed node using VT-100 terminal or TELNET. A get request always returns a NULL string.
STR sysGenCurrentCodeRelease	1.3.6.1.4.1.43.1.12.3.1.1.1.1.8	DisplayString	read-only	Firmware revision of the current code running in the managed node.
TIM sysTimeAndDate	1.3.6.1.4.1.43.1.12.3.1.1.1.2	TimeAndDate	read-write	Time and date maintained in the managed node.
sysIpConfig	1.3.6.1.4.1.43.1.12.3.1.1.1.3
sysIpConfigLocalHost	1.3.6.1.4.1.43.1.12.3.1.1.1.3.1
STR sysIpConfigLocalHostCommunityName	1.3.6.1.4.1.43.1.12.3.1.1.1.3.1.1	DisplayString	read-write	Community name of the managed node. A get request always returns a NULL string.
IP sysIpConfigLocalHostIpAddress	1.3.6.1.4.1.43.1.12.3.1.1.1.3.1.2	IpAddress	read-only	Local host's Ethernet IP address.
IP sysIpConfigLocalHostSubnetMask	1.3.6.1.4.1.43.1.12.3.1.1.1.3.1.3	IpAddress	read-only	Local host's Ethernet IP subnet mask.
PHY sysIpConfigLocalHostMacAddress	1.3.6.1.4.1.43.1.12.3.1.1.1.3.1.4	PhysAddress	read-only	Local host's Ethernet MAC-layer address.
sysIpConfigTrapGateway	1.3.6.1.4.1.43.1.12.3.1.1.1.3.2
IP sysIpConfigTrapGatewayIpAddress	1.3.6.1.4.1.43.1.12.3.1.1.1.3.2.1	IpAddress	read-write	Trap gateway's IP address.
IP sysIpConfigTrapGatewaySubnetMask	1.3.6.1.4.1.43.1.12.3.1.1.1.3.2.2	IpAddress	read-write	Trap gateway's IP subnet mask.
sysIpConfigTrapClientTable	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3		not-accessible	Trap client table has 4 entries
sysIpConfigTrapClientEntry	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3.1		not-accessible	Each entry contains IP address and port number of an SNMP manager which receives traps from the managed node.
INT sysIpConfigTrapClientIndex	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3.1.1	INTEGER	not-accessible
IP sysIpConfigTrapClientIpAddress	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3.1.2	IpAddress	read-write	Trap client's IP address.
IP sysIpConfigTrapClientSubnetMask	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3.1.3	IpAddress	read-write	Trap client's IP subnet mask.
INT sysIpConfigTrapClientPortNumber	1.3.6.1.4.1.43.1.12.3.1.1.1.3.3.1.4	INTEGER	read-write	Trap client's port number.
sysRs232Table	1.3.6.1.4.1.43.1.12.3.1.1.1.4		not-accessible	This table contains 2 rows. The first row shows the physical configuration of the port connected to a VT100 termianl. The second row is used to configure the port which supports SLIP. Access to the first row is read-only and access to the second row is read-write.
sysRs232Entry	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1		not-accessible	Each entry contains the attributes of a serial port.
INT sysRs232Port	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1.1	INTEGER	not-accessible	The managed node has 2 serial ports: port 1 and port 2.
INT sysRs232BaudRate	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1.2	INTEGER	read-write	Baud rate. The instance of this object in port-1 is read-only.
INT sysRs232Parity	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1.3	INTEGER	read-write	Parity. The instance of this object in port-1 is read-only.
INT sysRs232DataBits	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1.4	INTEGER	read-write	Number of data bits. The instance of this object in port-1 is read-only.
INT sysRs232StopBits	1.3.6.1.4.1.43.1.12.3.1.1.1.4.1.5	INTEGER	read-write	Number of stop bits. The instance of this object in port-1 is read-only.
INT sysRefClock	1.3.6.1.4.1.43.1.12.3.1.1.1.5	INTEGER	read-write	System reference clock maintained in the managed node.
INT sysProductType	1.3.6.1.4.1.43.1.12.3.1.1.1.6	INTEGER	read-only	System Product Type contain type of product.
OCT shelfSerialNumber	1.3.6.1.4.1.43.1.12.3.1.1.2.1	OCTET STRING	read-only	Serial number of the shelf.
OCT shelfRevision	1.3.6.1.4.1.43.1.12.3.1.1.2.2	OCTET STRING	read-only	Hardware revision number of the shelf.
shelfPowerSupplyTable	1.3.6.1.4.1.43.1.12.3.1.1.2.3		not-accessible	The power supply table in the shelf.
shelfPowerSupplyEntry	1.3.6.1.4.1.43.1.12.3.1.1.2.3.1		not-accessible	Information of the power supply in the shelf.
INT shelfPowerSupplySlot	1.3.6.1.4.1.43.1.12.3.1.1.2.3.1.1	INTEGER	not-accessible	Slot number of the power supply.
ADM shelfPowerSupplyAdminStatus	1.3.6.1.4.1.43.1.12.3.1.1.2.3.1.2	AdminStatus	read-write	Administrative status.
INT shelfPowerSupplyOperStatus	1.3.6.1.4.1.43.1.12.3.1.1.2.3.1.3	INTEGER	read-only	Operational status for Power Supply. In AB9300/AB9100, it doesn't support any setting value.
OCT shelfPartNumber	1.3.6.1.4.1.43.1.12.3.1.1.2.4	OCTET STRING	read-only	Part number of the shelf.
cardBaseTable	1.3.6.1.4.1.43.1.12.3.1.1.3.1		not-accessible	A 6 entry card table in the shelf.
cardBaseEntry	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1		not-accessible	Each card entry contains objects that refer to the card in that entry.
INT cardSlot	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.1	INTEGER	not-accessible	Slot number of the card in the shelf. The assignment of the card slots is as follows: slot 1 : management cpu, slot 2 : ctx card, slot 3 : one of the trunk cards (e.g. ds3/oc3/e3/hssi), slot 4-6: one of the port cards (e.g. ether/cbr/qsim).
CAR cardTypeDb	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.2	CardType	read-write	The configured card type in the slot. It may differ from the actual card type (cardTypeHw) in the corresponding slot. A set request will be accepted only when one of the following is true: 1. the value of cardTypeHw in this slot is none, or 2. the new value of cardTypeDb is the same as the corresponding cardTypeHw.
CAR cardTypeHw	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.3	CardType	read-only	The actual card type in the slot.
ADM cardAdminStatus	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.4	AdminStatus	read-write	Administrative status of the card. An error is returned if this slot has been selected as the system reference clock and an attempt is made to change this object to out-of-service. This object does not apply to management cpu and ctx card.
CAR cardOperStatus	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.5	CardOperStatus	read-only	Operational status of the card.
OCT cardSerialNumber	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.6	OCTET STRING	read-only	Serial number of the card.
OCT cardRevision	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.7	OCTET STRING	read-only	Hardware revision number of the card.
STR cardPartNumber	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.8	DisplayString	read-only	Part number of the card.
INT cardReset	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.9	INTEGER	read-write	This is the command to reset the card at the specified slot number. A read request always returns 0. Warning: Reseting card will temporarily disrupt traffic on the specified slot number.
CAR cardShelfState	1.3.6.1.4.1.43.1.12.3.1.1.3.1.1.10	CardShelfState	read-only	Operational shelf state of the card.
portBaseTable	1.3.6.1.4.1.43.1.12.3.1.1.4.1		not-accessible	The port information table.
portBaseEntry	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1		not-accessible	Each port entry contains objects that refer to the port in that entry.
INT portSlot	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.1	INTEGER	not-accessible	Slot Number. This table does not have objects for management cpu (slot #1) and ctx card (slot #2).
INT portNumber	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.2	INTEGER	not-accessible	Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
ADM portAdminStatus	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.3	AdminStatus	read-write	Administrative status of the port. An error is returned if this port has been selected as the system reference clock and an attempt is made to change this object to out-of-service.
POR portOperStatus	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.4	PortOperStatus	read-only	Operational status of the port.
INT portIfIndex	1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.5	INTEGER	read-only	Currently this object applies to the interface ports in port cards ONLY. It is pre-assigned as following: slot range 3 1..8 4 9..16 5 17..24 6 25..32 7 33..40 8 41..48 9 49..57
INT vcpNextAvailGlobVcSideId	1.3.6.1.4.1.43.1.12.3.1.1.5.2	INTEGER	read-only	This unique value which identified the next available virtual circuit ID. It is allowed NMS manager to get the next available Virtual Circuit Id before created a new row into Virtual circuit Path Table.
vcpBaseTable	1.3.6.1.4.1.43.1.12.3.1.1.5.3		not-accessible	The base virtual circuit table contains the common information for both sides of circuit.
vcpBaseEntry	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1		not-accessible	Information of the base virtual circuit.
INT vcpSideAId	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.1	INTEGER	not-accessible	A unique value which identifies the SideA of circuit.
INT vcpSideBId	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.2	INTEGER	not-accessible	A unique value which identifies the SideB of circuit.
VCP vcpLinkType	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.3	VcpLinkType	read-write	Vc Circuit Type indicated whether this circuit is Regular, Multicast, Management, Unicast, leaf.
STR vcpDescription	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.4	DisplayString	read-write	Vc description of circuits.
ADM vcpAdminStatus	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.5	AdminStatus	read-write	Vc administrative status.
INT vcpRowStatus	1.3.6.1.4.1.43.1.12.3.1.1.5.3.1.6	INTEGER	read-write	This object indicates the action to be taken by a set request.
vcpSideTable	1.3.6.1.4.1.43.1.12.3.1.1.5.4		not-accessible	The side table contains the Side A or Side B of circuit information.
vcpSideEntry	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1		not-accessible	Information of the base virtual circuit.
INT vcpSideId	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.1	INTEGER	not-accessible	unique number associated with virtual circuit.
INT vcpSideSlot	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.2	INTEGER	read-write	Slot Number. This table does not have objects for ctx card (slot #2) and card (slot #3).
INT vcpSidePort	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.3	INTEGER	read-write	Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- mcpu 1..1 ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-csu-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-csu-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
INT vcpSideTransmitVpi	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.4	INTEGER	read-write	Port card transmit vpi.
INT vcpSideTransmitVci	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.5	INTEGER	read-write	Port card transmit vci.
INT vcpSideReceiveVpi	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.6	INTEGER	read-write	Port card receive vpi. The value range 0..255 applies when VPI-only translation is requested. Otherwise, its range is 0..15. If the value of an instance of this object is > 15, the value of the corresponding instance of vcPortReceiveVci MUST be 0 (VPI-only translation).
INT vcpSideReceiveVci	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.7	INTEGER	read-write	Port card receive vci. If the value of this object is 0, VPI-only translation is requested.
INT vcpSidePriority	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.8	INTEGER	read-write	Priority queue is to prioritize the circuit. The smallest number is the highest priority. The largest number is lowest priority.
VCP vcpSidePacketDiscard	1.3.6.1.4.1.43.1.12.3.1.1.5.4.1.9	VcpPacketDiscard	read-write	Packet Discard indicates whether this packet needs to drop off based on the threshold.
vcpMappingSideTable	1.3.6.1.4.1.43.1.12.3.1.1.5.5		not-accessible	The Mapping side table contains circuit Side information.
vcpMappingSideEntry	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1		not-accessible	Information of the base virtual circuit.
INT vcpMappingSideSlot	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.1	INTEGER	not-accessible	Slot Number. This table does not have objects for ctx card (slot #2) and card (slot #3).
INT vcpMappingSidePort	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.2	INTEGER	not-accessible	Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- mcpu 1..1 ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-csu-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-csu-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
INT vcpMappingSideAId	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.3	INTEGER	not-accessible	SideA ID is a unique number associated with virtual circuit.
INT vcpMappingSideBId	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.4	INTEGER	not-accessible	SideB ID is a unique number associated with virtual circuit.
CAR vcpMappingCardType	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.5	CardType	read-only	card Type associated with mySide of circuit.
VCF vcpMappingFamCardType	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.6	VcFamilyCardType	read-only	Family Card Type associate with mySide of circuit.
CAR vcpMappingOtherCardType	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.7	CardType	read-only	Other Side of Card Type associate with the circuit.
VCF vcpMappingOtherFamCardType	1.3.6.1.4.1.43.1.12.3.1.1.5.5.1.8	VcFamilyCardType	read-only	Other Side of Family Card Type associate with the circuit.
INT faultClearCurrentAlarms	1.3.6.1.4.1.43.1.12.3.1.1.6.1	INTEGER	read-write	A set request clears all entries in the current alarm table. A get/get-next request returns 0.
INT faultClearHistoryAlarms	1.3.6.1.4.1.43.1.12.3.1.1.6.2	INTEGER	read-write	A set request clears all entries in the history alarm table. A get/get-next request returns 0.
faultCurrentAlarmTable	1.3.6.1.4.1.43.1.12.3.1.1.6.3		not-accessible	Current alarm table.
faultCurrentAlarmEntry	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1		not-accessible	Each entry in the table contains the information of a currently active alarm.
INT faultCurrentAlarmTag	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.1	INTEGER	not-accessible	The tag of the alarm in the current alarm table.
ALA faultCurrentAlarmAlarmType	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.2	AlarmType	read-only	Alarm type.
INT faultCurrentAlarmSeverity	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.3	INTEGER	read-only	Alarm severity.
CAR faultCurrentAlarmCardType	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.4	CardType	read-only	Card type of the card which caused the alarm.
INT faultCurrentAlarmCardNumber	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.5	INTEGER	read-only	Slot number of the card which caused the alarm.
INT faultCurrentAlarmPortNumber	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.6	INTEGER	read-only	The port number of the card which caused the alarm.
TIM faultCurrentAlarmSetTime	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.7	TimeAndDate	read-only	The time when the alarm was set.
STR faultCurrentAlarmDescription	1.3.6.1.4.1.43.1.12.3.1.1.6.3.1.8	DisplayString	read-only	A readable string which describes the alarm.
faultHistoryAlarmTable	1.3.6.1.4.1.43.1.12.3.1.1.6.4		not-accessible	History/Information alarm table.
faultHistoryAlarmEntry	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1		not-accessible	Each entry in the history alarm table contains either a cleared alarm or an information alarm.
INT faultHistoryAlarmTag	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.1	INTEGER	not-accessible	The tag of the alarm in the history alarm table.
ALA faultHistoryAlarmAlarmType	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.2	AlarmType	read-only	Alarm type.
INT faultHistoryAlarmSeverity	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.3	INTEGER	read-only	Severity of the alarm.
CAR faultHistoryAlarmCardType	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.4	CardType	read-only	Card type of the card which caused the alarm.
INT faultHistoryAlarmCardNumber	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.5	INTEGER	read-only	Slot number of the card which caused the alarm.
INT faultHistoryAlarmPortNumber	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.6	INTEGER	read-only	Port number of the card which caused the alarm.
TIM faultHistoryAlarmSetTime	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.7	TimeAndDate	read-only	The time when the alarm was set.
STR faultHistoryAlarmDescription	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.8	DisplayString	read-only	A readable string which describes the alarm.
TIM faultHistoryAlarmClearTime	1.3.6.1.4.1.43.1.12.3.1.1.6.4.1.9	TimeAndDate	read-only	The time when the alarm was cleared.

RFC description

Base product MIB providing core system objects and root organization for vendor product hierarchy.

Start monitoring Networking equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download C-PRODUCT-BASE-MIB

What Is C-PRODUCT-BASE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description