AirPairv2cTrap-MIB

All MIBs › AirPairv2cTrap-MIB

Description: SNMPv2c trap notification definitions for DragonWave AirPair wireless radio systems, including cold-start, link-up/down, and peer authentication failure events

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AirPairv2cTrap-MIB?

AirPairv2cTrap-MIB is a DragonWave proprietary module defining SNMPv2c trap notifications for the AirPair family of point-to-point wireless microwave radio systems used in backhaul networking. Its data consists entirely of fault/event notification definitions rather than polled tables, covering events such as cold-start, link-up/link-down state transitions, and peer authentication failures. This module is explicitly for monitoring software and link operational status: it alerts operators in near real time when a radio link drops, a unit restarts, or an authentication handshake with a paired radio fails, which are critical events for maintaining wireless backhaul availability. It builds on the standard SNMPv2 trap/notification framework (SNMPv2-TRAP-MIB conventions) for its notification structure. It is deployed in wireless backhaul networks using DragonWave AirPair microwave radio links, typically monitored by a network management system configured to receive and alert on these traps, with an AirPairv2cTrap-MIB download being the first step in configuring that trap receiver correctly.

IPNetwork Monitor allows you to monitor SNMP objects defined in AirPairv2cTrap-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DragonWave AirPair microwave radio system

Monitoring Examples

No runtime data objects were provided for this module since it is trap-only; a network management system would be configured as an SNMPv2c trap receiver for the AirPair radios, and receiving a link-down trap for a given radio interface, or a peer-authentication-failure trap, would immediately alert operators to a microwave backhaul outage or a possible unauthorized/misconfigured peer pairing attempt.

What Can Be Monitored

link up/down events
cold-start events
peer authentication failure events

Imported Objects

From AirPair-MIB

airPair	OBJECT-IDENTITY
ttySessionUserConnectionType	OBJECT-TYPE
ttySessionUserName	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE
ifIndex

From SNMPv2-SMI

IpAddress
NOTIFICATION-TYPE

OIDs

OID symbolic	OID numeric	Description
apSnmpV2Notification	1.3.6.1.4.1.7262.1.26
apSnmpV2Traps	1.3.6.1.4.1.7262.1.26.0
NTF coldStartV2c	1.3.6.1.4.1.7262.1.26.0.0	A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered.
NTF linkDownV2c	1.3.6.1.4.1.7262.1.26.0.1	A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration.
NTF linkUpV2c	1.3.6.1.4.1.7262.1.26.0.2	A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up.
NTF explicitAuthenticationFailureV2c	1.3.6.1.4.1.7262.1.26.0.3	Authentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.
NTF autoNegotiationDuplexMismatchV2c	1.3.6.1.4.1.7262.1.26.0.4	The AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to AirPair, or the AirPair autonegotion settings. The recommended course of action is to check the connection.
NTF modemLossOfSignalLockFromDemodulatorV2c	1.3.6.1.4.1.7262.1.26.0.5	Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.
NTF modemUncorrectedBerThresholdExceededV2c	1.3.6.1.4.1.7262.1.26.0.6	The uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes.
NTF modemModulatorPllLockFailureV2c	1.3.6.1.4.1.7262.1.26.0.7	Modulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the modem unit.
NTF modemModulatorLossOfSyncBytesV2c	1.3.6.1.4.1.7262.1.26.0.8	Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the air pair nodes.
NTF modemModulatorInputFifoErrorV2c	1.3.6.1.4.1.7262.1.26.0.9	Overrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or relpace the modem unit.
NTF modemModulatorInputDataErrorV2c	1.3.6.1.4.1.7262.1.26.0.10	All ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or replace the modem unit.
NTF modemSnrBelowThresholdV2c	1.3.6.1.4.1.7262.1.26.0.11	The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes.
NTF radioPLDROLostLockV2c	1.3.6.1.4.1.7262.1.26.0.12	The PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit.
NTF radioLostCommunicationV2c	1.3.6.1.4.1.7262.1.26.0.13	RS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recommended course of action is to check the connection.
NTF radioMismatchV2c	1.3.6.1.4.1.7262.1.26.0.14	The radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrectly programmed modem or an incorrect radio type connected to the modem, and recommended course of action is to check the modem frequency settings and radio hardware version number or serial number.
NTF radioPowerAmpV2c	1.3.6.1.4.1.7262.1.26.0.15	The power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit.
NTF ifTxSynthUnlockedV2c	1.3.6.1.4.1.7262.1.26.0.16	The IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit.
NTF ifRxSynthUnlockedV2c	1.3.6.1.4.1.7262.1.26.0.17	The IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit.
NTF ttySessionCommencedV2c	1.3.6.1.4.1.7262.1.26.0.18	A person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap.
NTF ttySessionTerminatedV2c	1.3.6.1.4.1.7262.1.26.0.19	A person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap.
NTF rslBelowThresholdV2c	1.3.6.1.4.1.7262.1.26.0.20	The RSL has been detected below its minimum threshold.
NTF droppedFramesThresholdExceededV2c	1.3.6.1.4.1.7262.1.26.0.21	The ethernet dropped frames threshold has been detected above its threshold value.
NTF bwUtilizationThresholdExceededV2c	1.3.6.1.4.1.7262.1.26.0.22	The ethernet bandwidth threshold has been detected above its threshold value.
NTF explicitAuthFailureClearedV2c	1.3.6.1.4.1.7262.1.26.0.23	The condition has cleared. The peer node is now authenticated.
NTF autoNegDuplexMismatchClearedV2c	1.3.6.1.4.1.7262.1.26.0.24	The condition has cleared. The Ethernet connection is not experiencing auto-negotiation duplex mismatch.
NTF lossOfSyncSigFromDemoClearedV2c	1.3.6.1.4.1.7262.1.26.0.25	The condition has cleared. The demodulator is synchronized.
NTF uncorrectedBerThresExceededClearedV2c	1.3.6.1.4.1.7262.1.26.0.26	The condition has cleared. The demodulator uncorrected BER is now below its minimum threshold value.
NTF modemModPLLFailureClearedV2c	1.3.6.1.4.1.7262.1.26.0.27	The condition has cleared. The modem PLL is not failing.
NTF modemModLossOfSyncBytesClearedV2c	1.3.6.1.4.1.7262.1.26.0.28	The condition has cleared. The modem is not experiencing loss of synch bytes.
NTF modemModInputFifoOverUnderClearedV2c	1.3.6.1.4.1.7262.1.26.0.29	The condition has cleared. The modem is not experiencing input FIFO over/under runs.
NTF modemModInputDataInacClearedV2c	1.3.6.1.4.1.7262.1.26.0.30	The condition has cleared. The modem is not experiencing data inactivity.
NTF snrBelowThresholdClearedV2c	1.3.6.1.4.1.7262.1.26.0.31	The condition has cleared. SNR is now above its minimum threshold value.
NTF radioPLDROLostLockClearedV2c	1.3.6.1.4.1.7262.1.26.0.32	The condition has cleared. The radio PLDRO/LO lost lock condition has cleared.
NTF radioLostCommunicationClearedV2c	1.3.6.1.4.1.7262.1.26.0.33	The condition has cleared. RS232 communication has been re-establisted between AIRPAIR and the radio.
NTF radioMismatchClearedV2c	1.3.6.1.4.1.7262.1.26.0.34	The condtion has cleared. The radio matches the programmed parameters in the modem.
NTF radioPowerAmpClearedV2c	1.3.6.1.4.1.7262.1.26.0.35	The condtion has cleared. The radio Power Amp is not in the failed state.
NTF ifTxSynthUnlockedClearedV2c	1.3.6.1.4.1.7262.1.26.0.36	The condtion has cleared. The IF stage transmit synthesizer is now locked.
NTF ifRxSynthUnlockedClearedV2c	1.3.6.1.4.1.7262.1.26.0.37	The condtion has cleared. The IF stage receive synthesizer is now locked.
NTF rslBelowThresholdClearedV2c	1.3.6.1.4.1.7262.1.26.0.38	The condition has cleared. RSL is now above its minimum threshold.
NTF droppedFramesThresholdExceededClearedV2c	1.3.6.1.4.1.7262.1.26.0.39	The condition has cleared.The ethernet dropped frames threshold is now below its threshold value.
NTF bwUtilizationThresholdExceededClearedV2c	1.3.6.1.4.1.7262.1.26.0.40	The condition has cleared. The ethernet bandwidth threshold is now below its threshold value.
NTF rxIfCableLossExceededV2c	1.3.6.1.4.1.7262.1.26.0.41	The Rx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split.
NTF rxIfCableLossExceededClearedV2c	1.3.6.1.4.1.7262.1.26.0.42	The condition has cleared. The Rx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF txIfCableLossExceededV2c	1.3.6.1.4.1.7262.1.26.0.43	The Tx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF txIfCableLossExceededClearedV2c	1.3.6.1.4.1.7262.1.26.0.44	The condition has cleared. The Tx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF fan1FailedV2c	1.3.6.1.4.1.7262.1.26.0.45	The Fan1 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF fan1FailedClearedV2c	1.3.6.1.4.1.7262.1.26.0.46	The condition has cleared. The fan1 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF fan2FailedV2c	1.3.6.1.4.1.7262.1.26.0.47	The Fan2 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF fan2FailedClearedV2c	1.3.6.1.4.1.7262.1.26.0.48	The condition has cleared. The fan2 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split
NTF modemCardMismatchedHardwareFirmwareV2c	1.3.6.1.4.1.7262.1.26.0.49	The modem card has incompatible hardware and firmware. The firmware will not run properly on this card.
NTF modemCardMismatchedHardwareFirmwareClearedV2c	1.3.6.1.4.1.7262.1.26.0.50	The condition has cleared. The modem card has compatible hardware and firmware. The firmware will run properly on this card.
NTF atpcConfigMismatchV2c	1.3.6.1.4.1.7262.1.26.0.51	ATPC configuration mismatch in the Airpair systems. ATPC is enabled at one system, but ATPC is not enabled at the other system.
NTF atpcConfigMismatchClearedV2c	1.3.6.1.4.1.7262.1.26.0.52	ATPC configuration mismatch in the Airpair systems is cleared. Both systems enabled ATPC.
NTF radioHiPwrOptM1V2c	1.3.6.1.4.1.7262.1.26.0.53	When hi-power radio is used, hi-power gate M1 drain current is out of lower or upper limits.
NTF radioHiPwrOptM1ClearedV2c	1.3.6.1.4.1.7262.1.26.0.54	When hi-power radio is used, hi-power gate M1 drain current is between lower and upper limits.
NTF radioHiPwrOptM2V2c	1.3.6.1.4.1.7262.1.26.0.55	When hi-power radio is used, hi-power gate M2 drain current is out of lower or upper limits.
NTF radioHiPwrOptM2ClearedV2c	1.3.6.1.4.1.7262.1.26.0.56	When hi-power radio is used, hi-power gate M2 drain current is between lower and upper limits.
NTF radioHiPwrTxDetectorV2c	1.3.6.1.4.1.7262.1.26.0.57	When hi-power radio is used, hi-power tx detector dBm value is smaller than limit.
NTF radioHiPwrTxDetectorClearedV2c	1.3.6.1.4.1.7262.1.26.0.58	When hi-power radio is used, hi-power tx detector dBm value is not smaller than limit.
NTF sntpServersUnreachableV2c	1.3.6.1.4.1.7262.1.26.0.59	Can't reach any of the sntp servers
NTF sntpServersUnreachableClearedV2c	1.3.6.1.4.1.7262.1.26.0.60	At least one of SNTP servers is reachable
NTF rlsMismatchV2c	1.3.6.1.4.1.7262.1.26.0.61	RLS mismatch
NTF rlsMismatchClearedV2c	1.3.6.1.4.1.7262.1.26.0.62	RLS mismatch cleared
NTF rLSShutdownActivatedV2c	1.3.6.1.4.1.7262.1.26.0.63	RLS shutdown is activated
NTF rLSShutdownActivatedClearedV2c	1.3.6.1.4.1.7262.1.26.0.64	RLS shutdown is not activated
NTF frequencyFileInvalidV2c	1.3.6.1.4.1.7262.1.26.0.65	When the executing frequency file is invalid, this trap is generated.
NTF optionalParaNotEntFreqFileV2c	1.3.6.1.4.1.7262.1.26.0.66	when the optional parameters are not entered in frequency file, and the system boots up, this trap is generated.
NTF progRadioBandNotFoundFreqFileV2c	1.3.6.1.4.1.7262.1.26.0.67	when the executing frequency file doesn't contain the info related to programmed radio band, this trap is generated.
NTF redundancySwitchOverSuccessV2c	1.3.6.1.4.1.7262.1.26.0.68	Radio Redundancy Switch over success
NTF redundancySwitchOverFailedV2c	1.3.6.1.4.1.7262.1.26.0.69	Radio Redundancy Switch over failed
NTF redundancyNoAtpcSupportV2c	1.3.6.1.4.1.7262.1.26.0.70	Radio does not support atpc
NTF redundancyNoAtpcSupportClearedV2c	1.3.6.1.4.1.7262.1.26.0.71	Radio does not support atpc cleared
NTF redundancyInvalidFirmwareV2c	1.3.6.1.4.1.7262.1.26.0.72	Radio firmware on radio and on modem card mismatch
NTF redundancyInvalidFirmwareClearedV2c	1.3.6.1.4.1.7262.1.26.0.73	Radio firmware mismatch cleared
NTF redundancySwitchInitByLocalendV2c	1.3.6.1.4.1.7262.1.26.0.74	Radio switch initiated by local end
NTF redundancySwitchInitByPeerV2c	1.3.6.1.4.1.7262.1.26.0.75	Radio switch initiated by peer
NTF aamConfigMisMatchV2c	1.3.6.1.4.1.7262.1.26.0.76	Automatic Adaptive modulation configuration mismatch
NTF aamConfigMisMatchClearV2c	1.3.6.1.4.1.7262.1.26.0.77	Automatic Adaptive modulation configuration mismatch cleared
NTF aamQpskActiveV2c	1.3.6.1.4.1.7262.1.26.0.78	Automatic Adaptive modulation running on QPSK modulation
NTF aamQpskActiveClearedV2c	1.3.6.1.4.1.7262.1.26.0.79	Automatic Adaptive modulation running on higher modulation
NTF primaryRadioFaultyV2c	1.3.6.1.4.1.7262.1.26.0.80	Primary radio is faulty.
NTF primaryRadioFaultyClearedV2c	1.3.6.1.4.1.7262.1.26.0.81	primary radio is not faulty anymore.
NTF radioSerialNumberMismatchV2c	1.3.6.1.4.1.7262.1.26.0.82	Redundancy, Radio Serial number mismatch.
NTF radioSerialNumberMismatchClearedV2c	1.3.6.1.4.1.7262.1.26.0.83	Redundancy, Radio Serial number mismatch cleared.
NTF excessiveCableLossChangeV2c	1.3.6.1.4.1.7262.1.26.0.84	Excessive cable loss change
NTF excessiveCableLossChangeClearedV2c	1.3.6.1.4.1.7262.1.26.0.85	Excessive cable loss change cleared

RFC description

Provides SNMPv2c trap notifications for DragonWave AirPair wireless links including link status and authentication events.

Start monitoring DragonWave AirPair microwave radio systems (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AirPairv2cTrap-MIB

What Is AirPairv2cTrap-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description