All MIBs › ATT-VPN-GATEWAY-MIB
Organization: AT&T
Last Updated: 2016-03-03
Category: VPN and Security, Vendor: AT&T
Description: Manages AT&T VPN gateway devices, providing tunnel establishment status, authentication events, and throughput metrics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ATT-VPN-GATEWAY-MIB?
ATT-VPN-GATEWAY-MIB is AT&T's enterprise MIB for its managed VPN Gateway customer-premises equipment, used to remotely manage and monitor small-business/branch VPN gateway devices as part of an AT&T managed-service offering. It exposes hardware and firmware identity (hardware version, code/firmware version), account and time-zone/DST configuration, WAN connection method and hostname, and a DNS server table, alongside tunnel/authentication and throughput data per the module's broader scope. It supports monitoring both software status - code/firmware version, DST/timezone configuration, WAN connection method - and basic device hardware version identity, which AT&T's back-end systems use to verify the gateway is running expected firmware and is correctly provisioned. It is a self-contained enterprise MIB but is used alongside standard host/interface MIBs by the managed-service monitoring platform for full device visibility. It is typically deployed on AT&T-managed VPN gateway appliances installed at customer branch/small-business sites and polled by AT&T's remote management infrastructure, with technicians performing an ATT-VPN-GATEWAY-MIB download to load the module into their SNMP management platform.
IPNetwork Monitor allows you to monitor SNMP objects defined in ATT-VPN-GATEWAY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- AT&T managed VPN gateway (branch/small-business CPE)
Monitoring Examples
A management system would poll nghwHardwareVersion and nghwCodeVersion to confirm the gateway is on approved hardware/firmware, and check nghwWanConnectionMethod and nghwHostname to verify WAN provisioning. Walking ngDnsTable/ngDnsEntry via ngdnIndex reveals which DNS servers are configured on the gateway. A mismatch between nghwCodeVersion and the expected fleet-wide firmware version would flag a device needing a firmware upgrade, while an unexpected nghwDstActive value could explain time-stamping discrepancies in logs.
What Can Be Monitored
- hardware version
- firmware/code version
- WAN connection method
- DNS server configuration
- DST/timezone status
- account identity
This MIB depends on
Related MIBs
Imported Objects
From INET-ADDRESS-MIB
| InetAddressIPv6 |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DateAndTime | |
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| att_2 | 1.3.6.1.4.1.74 | |||
| att_products | 1.3.6.1.4.1.74.1 | |||
| attVpnGateway | 1.3.6.1.4.1.74.1.30 | |||
| ngHardwareInfo | 1.3.6.1.4.1.74.1.30.1 | |||
| STR nghwHardwareVersion | 1.3.6.1.4.1.74.1.30.1.1 | DisplayString | read-only | Hardware Version. |
| STR nghwCodeVersion | 1.3.6.1.4.1.74.1.30.1.2 | DisplayString | read-only | Software code version. |
| STR nghwAccount | 1.3.6.1.4.1.74.1.30.1.3 | DisplayString | read-only | The account in Service Manager this device is registered under. |
| I32 nghwUtcOffset | 1.3.6.1.4.1.74.1.30.1.4 | Integer32 | read-only | Indicates how many minutes away from UTC time the device is located. Values must be in 30 minute increments. Valid range is -840 to 840. |
| INT nghwDstAllowed | 1.3.6.1.4.1.74.1.30.1.5 | INTEGER | read-only | Indicates if the device is located in an area that observes daylight savings time. |
| INT nghwDstActive | 1.3.6.1.4.1.74.1.30.1.6 | INTEGER | read-only | Indicates if daylight savings time is current active at this date and time. |
| INT nghwWanConnectionMethod | 1.3.6.1.4.1.74.1.30.1.7 | INTEGER | read-only | The current primary IPv4 WAN connection setting. This is configured via the web interface and is not read from Service Manager. |
| STR nghwHostname | 1.3.6.1.4.1.74.1.30.1.8 | DisplayString | read-only | The name of the current host. |
| nghwDnsServers | 1.3.6.1.4.1.74.1.30.1.9 | |||
| ngDnsTable | 1.3.6.1.4.1.74.1.30.1.9.1 | not-accessible | The (conceptual) table of DNS on the device. An entry shall be placed in the storage table for each DNS. | |
| ngDnsEntry | 1.3.6.1.4.1.74.1.30.1.9.1.1 | not-accessible | A (conceptual) entry for one logical DNS area on the host. | |
| I32 ngdnIndex | 1.3.6.1.4.1.74.1.30.1.9.1.1.1 | Integer32 | not-accessible | A unique value for each logical DNS contained on the device. |
| IP ngdnServer | 1.3.6.1.4.1.74.1.30.1.9.1.1.2 | IpAddress | read-only | The IP address of an indivdual name server in use. |
| ngDnsIPv6Table | 1.3.6.1.4.1.74.1.30.1.9.2 | not-accessible | The (conceptual) table of IPv6 DNS on the device. An entry shall be placed in the storage table for each DNS. | |
| ngDnsIPv6Entry | 1.3.6.1.4.1.74.1.30.1.9.2.1 | not-accessible | A (conceptual) entry for one logical IPv6 DNS area on the host. | |
| I32 ngdnIPv6Index | 1.3.6.1.4.1.74.1.30.1.9.2.1.1 | Integer32 | not-accessible | A unique value for each logical IPv6 DNS contained on the device. |
| ADR ngdnIPv6Server | 1.3.6.1.4.1.74.1.30.1.9.2.1.2 | InetAddressIPv6 | read-only | The IPv6 IP address of an indivdual name server in use. |
| INT nghwDeviceStatus | 1.3.6.1.4.1.74.1.30.1.10 | INTEGER | read-only | The current device status. |
| STR nghwLanguage | 1.3.6.1.4.1.74.1.30.1.11 | DisplayString | read-only | The language that will be displayed on the CGI web interface. The valid values are: EN = English JA = Japanese ES = Spanish BP = Brazil Portuguese FC = French Canadian TC = Traditional Chinese SC = Simplified Chinese |
| nghwCustComm | 1.3.6.1.4.1.74.1.30.1.12 | |||
| ngCustCommTable | 1.3.6.1.4.1.74.1.30.1.12.1 | not-accessible | The (conceptual) table of customer info (such as comments) on the device. An entry shall be placed in the storage table for each one. | |
| ngCustCommEntry | 1.3.6.1.4.1.74.1.30.1.12.1.1 | not-accessible | A (conceptual) entry for one logical customer comment area on the host. | |
| I32 ngcuIndex | 1.3.6.1.4.1.74.1.30.1.12.1.1.1 | Integer32 | not-accessible | A unique value for each logical customer info. |
| STR ngcuCustComment | 1.3.6.1.4.1.74.1.30.1.12.1.1.2 | DisplayString | read-only | A free-format field that can be added to the AT&T VPN Gateway's profile at a customer's request. Currently only one comment field can be specified. |
| nghwPorts | 1.3.6.1.4.1.74.1.30.1.13 | |||
| ngPortTable | 1.3.6.1.4.1.74.1.30.1.13.1 | not-accessible | The (conceptual) table of ports on the device. An entry shall be placed in the storage table for each port. | |
| ngPortEntry | 1.3.6.1.4.1.74.1.30.1.13.1.1 | not-accessible | A (conceptual) entry for one logical port area on the host. | |
| I32 ngpoIndex | 1.3.6.1.4.1.74.1.30.1.13.1.1.1 | Integer32 | not-accessible | A unique value for each logical port contained on the device. |
| INT ngpoStatus | 1.3.6.1.4.1.74.1.30.1.13.1.1.2 | INTEGER | read-only | The link status of an individual hardware port. |
| INT nghwCurrentWanConnectionMethod | 1.3.6.1.4.1.74.1.30.1.14 | INTEGER | read-only | The currently active IPv4 WAN connection, which may differ from the configured primary IPv4 WAN connection setting. For example, the primary IPv4 WAN is configured for DHCP (wanConfigDHCP), but because of a network outage the PPPoE secondary WAN connection (wanConfigPPPoE2) is currently providing connectivity. |
| INT nghwIPv6WanConnectionMethod | 1.3.6.1.4.1.74.1.30.1.15 | INTEGER | read-only | The current primary IPv6 WAN connection setting. This is configured via the web interface and is not read from Service Manager. |
| INT nghwIPv6CurrentWanConnectionMethod | 1.3.6.1.4.1.74.1.30.1.16 | INTEGER | read-only | The currently active IPv6 WAN connection, which may differ from the configured primary IPv6 WAN connection setting. For example, the primary IPv4 WAN is configured for DHCP (wanConfigIPv6DHCP), but because of a network outage the static IP secondary WAN connection (wanConfigIPv6Static2) is currently providing connectivity. |
| DAT nghwLastFullQueryTimeDAT | 1.3.6.1.4.1.74.1.30.1.17 | DateAndTime | read-only | The last time when the AT&T VPN Gateway was successfully able to retrieve its full profile from an AT&T Administration Server. |
| DAT nghwLastAnyQueryTimeDAT | 1.3.6.1.4.1.74.1.30.1.18 | DateAndTime | read-only | The last time when the AT&T VPN Gateway was successfully able to retrieve its profile from an AT&T Administration Server. If this time does not match nghwLastFullQueryTimeDAT then that means only part of the profile was retrieved. This is to prevent any possible reboots if critical portions of the profile were to change. |
| DAT nghwLastUpgradeTimeDAT | 1.3.6.1.4.1.74.1.30.1.19 | DateAndTime | read-only | The last time when the software version of AT&T VPN Gateway was successfully upgraded. Returns January 1 year 0 time 0 when this cannot be determined. |
| STR hwMac | 1.3.6.1.4.1.74.1.30.1.20 | DisplayString | read-only | The main WAN MAC address of this device used to identify its profile in Service Manager. |
| STR hwRollbackVersion | 1.3.6.1.4.1.74.1.30.1.21 | DisplayString | read-only | Software code version that will be used if the rollback feature is activated. |
| INT hwDualWan | 1.3.6.1.4.1.74.1.30.1.22 | INTEGER | read-only | Ties to the 'Use as Internet Primary' field in Service Manager. Controls the Dual WAN configuration. |
| INT hwWan2ConnectionMethod | 1.3.6.1.4.1.74.1.30.1.23 | INTEGER | read-only | The current WAN2 IPv4 WAN connection setting. This is not configured via the web interface and is read from Service Manager. |
| INT hwIPv6Wan2ConnectionMethod | 1.3.6.1.4.1.74.1.30.1.24 | INTEGER | read-only | The current WAN2 IPv6 WAN connection setting. This is not configured via the web interface and is read from Service Manager. |
| STR hwWan1GwayMac | 1.3.6.1.4.1.74.1.30.1.25 | DisplayString | read-only | This is the MAC Address of the WAN1 Gateway router if it is in use. For MAC Address range from 002704000000 to 002704009999, it is a NetBridge (SX) device. For MAC Address range from 002704010000 to 002704010425, it is a NetBridge (FX) device. For MAC Address range from 002704010426 to 002704019999, it is a Cell Extender (6200-FX) device. For MAC Address range from 002704270000 to 002704279999, it is a Cell Extender (6300-CX) device. |
| STR hwWan2Mac | 1.3.6.1.4.1.74.1.30.1.26 | DisplayString | read-only | This is the MAC Address of the WAN2 interface if it is in use. |
| STR hwWan2GwayMac | 1.3.6.1.4.1.74.1.30.1.27 | DisplayString | read-only | This is the MAC Address of the WAN2 Gateway router if it is in use. For MAC Address range from 002704000000 to 002704009999, it is a NetBridge (SX) device. For MAC Address range from 002704010000 to 002704010425, it is a NetBridge (FX) device. For MAC Address range from 002704010426 to 002704019999, it is a Cell Extender (6200-FX) device. For MAC Address range from 002704270000 to 002704279999, it is a Cell Extender (6300-CX) device. |
| ngInterfaceInfo | 1.3.6.1.4.1.74.1.30.2 | |||
| STR ngifActiveWanIface | 1.3.6.1.4.1.74.1.30.2.1 | DisplayString | read-only | The interface that is currently in use for the primary connection. |
| U32 ngifTotalBytesIn | 1.3.6.1.4.1.74.1.30.2.2 | Unsigned32 | read-only | Total bytes in on the active WAN interface. |
| U32 ngifTotalBytesOut | 1.3.6.1.4.1.74.1.30.2.3 | Unsigned32 | read-only | Total bytes out on the active WAN interface. |
| TIK ngifTimeInDial | 1.3.6.1.4.1.74.1.30.2.4 | TimeTicks | read-only | How long the current dial connection has been up. |
| TIK ifTimeInBackup | 1.3.6.1.4.1.74.1.30.2.5 | TimeTicks | read-only | How long the backup connection has been up. This is very similar to ngifTimeInDial. The difference is that ngifTimeInDial isn't necessarily measuring a backup connection. For example, when configured for 'Dial As Primary' ifTimeInBackup will always remain zero because there is no backup for Dial As Primary but ngifTimeInDial will be non-zero when the connection is up. In other WAN configurations (such as DHCP, for example) both ngifTimeInDial and ifTimeInBackup will be non-zero when the backup connection is in use. |
| INT ifInterfaceFormat | 1.3.6.1.4.1.74.1.30.2.6 | INTEGER | read-only | Setting from the Service Manager profile that controls SNMP interface persistence. Zero indicates that this feature is not in use. |
| ifIfaceStats | 1.3.6.1.4.1.74.1.30.2.7 | |||
| ifStatTable | 1.3.6.1.4.1.74.1.30.2.7.1 | not-accessible | The (conceptual) table of interface statistics on the device. An entry shall be placed in the storage table for each interface statistic. | |
| ifStatEntry | 1.3.6.1.4.1.74.1.30.2.7.1.1 | not-accessible | A (conceptual) entry for one logical interface statistic area. | |
| I32 ifStatsMainIndex | 1.3.6.1.4.1.74.1.30.2.7.1.1.1 | Integer32 | not-accessible | A unique value for each logical interface statistic. |
| I32 ifStatsifIndex | 1.3.6.1.4.1.74.1.30.2.7.1.1.2 | Integer32 | read-only | The value of this index reported by ifIndex in the standard MIBs. This is needed because index numbers can be skipped in the standard MIBs. |
| STR ifStatsifDescr | 1.3.6.1.4.1.74.1.30.2.7.1.1.3 | DisplayString | read-only | A textual string containing information about the interface. |
| U32 ifStatsRxCrcErr | 1.3.6.1.4.1.74.1.30.2.7.1.1.4 | Unsigned32 | read-only | Received CRC errors for the interface. |
| STR ifCircuitSpeed | 1.3.6.1.4.1.74.1.30.2.8 | DisplayString | read-only | Informational string that is pulled from the device profile. Useful for the scenario where the physical connection to the WAN interface will be 10, 100 or 1000 Mbps (depending on the ISP modem/router) but the speed allocated by the ISP will be much lower (2, 4, or 8 Mbps). This field does not control speed and does not indicate a measurement of speed. It is manually entered by an administrator for informational purposes only. |
| ngVlanInfo | 1.3.6.1.4.1.74.1.30.3 | |||
| ngVlanTable | 1.3.6.1.4.1.74.1.30.3.1 | not-accessible | The (conceptual) table of VLANs on the device. An entry shall be placed in the storage table for each VLAN. | |
| ngVlanEntry | 1.3.6.1.4.1.74.1.30.3.1.1 | not-accessible | A (conceptual) entry for one logical VLAN area on the host. | |
| I32 ngvlIndex | 1.3.6.1.4.1.74.1.30.3.1.1.1 | Integer32 | not-accessible | A unique value for each logical VLAN contained by the device. |
| I32 ngvlId | 1.3.6.1.4.1.74.1.30.3.1.1.2 | Integer32 | read-only | This is the number assigned to the VLAN. Please note: A VLAN with an ID of 4070 is a special VLAN used to hold ports that are disabled. |
| STR ngvlPorts | 1.3.6.1.4.1.74.1.30.3.1.1.3 | DisplayString | read-only | The ports assigned to the VLAN. |
| INT ngvlSpeed | 1.3.6.1.4.1.74.1.30.3.1.1.4 | INTEGER | read-only | This is the speed supported on the VLAN Ethernet interfaces. If the VLAN Ethernet speed is configured for auto negotiation then autoNegot will be reported and the negotiated speed will be reported by ngvlSpeedCurrent. If the VLAN Ethernet speed is configured for a specific speed that speed will be reported. |
| STR ngvlIpRange | 1.3.6.1.4.1.74.1.30.3.1.1.5 | DisplayString | read-only | The range of IP addresses handed out via DHCP on this VLAN. Values will be 0.0.0.0 0.0.0.0 if DHCP is not enabled on this VLAN. Followed by number of addresses assigned and number of total addresses. NOTE: As of AT&T VPN Gateway version 5.3 the number of addresses assigned will no longer be returned. A zero will be returned for that field. |
| STR ngvlDhcpRelayAddr | 1.3.6.1.4.1.74.1.30.3.1.1.6 | DisplayString | read-only | When the DHCP Type is 'R', this is the address the AT&T VPN Gateway devices uses to relay DHCP requests. This field is required when the DHCP Type is 'R'. A second address can be specified. |
| IP ngvlDhcpDefRoute | 1.3.6.1.4.1.74.1.30.3.1.1.7 | IpAddress | read-only | This field is required when VRRP Active Indicator is 'Y' and is optional otherwise. If specified, it must be within the local LAN subnet of the AT&T VPN Gateway but cannot fall within the DHCP pool start and end addresses. For the DHCP Default Route on the AT&T VPN Gateway device profile, if entered, the address must be within the network specified by the LAN Address and LAN Subnet, but not within the address range specified by the DHCP Start Address and DHCP End Address. |
| IP ngvlLanAddr | 1.3.6.1.4.1.74.1.30.3.1.1.8 | IpAddress | read-only | This is the LAN address for the device on the VLAN. |
| IP ngvlLanSubAddr | 1.3.6.1.4.1.74.1.30.3.1.1.9 | IpAddress | read-only | This is the LAN subnet address for the device on the VLAN. |
| ADR ngvlIPv6IpRangeStart | 1.3.6.1.4.1.74.1.30.3.1.1.10 | InetAddressIPv6 | read-only | The start of the range of IPv6 IP addresses handed out via DHCP on this VLAN. Value will be all zeroes if DHCP is not enabled on this VLAN. |
| ADR ngvlIPv6IpRangeEnd | 1.3.6.1.4.1.74.1.30.3.1.1.11 | InetAddressIPv6 | read-only | The end of the range of IPv6 IP addresses handed out via DHCP on this VLAN. Value will be all zeroes if DHCP is not enabled on this VLAN. |
| ADR ngvlIPv6DhcpRelayAddrPri | 1.3.6.1.4.1.74.1.30.3.1.1.12 | InetAddressIPv6 | read-only | When the DHCP Type is 'R', this is the primary address the AT&T VPN Gateway devices uses to relay DHCP requests. This field is required when the DHCP Type is 'R' and IPv6 is in use. |
| ADR ngvlIPv6DhcpRelayAddrBak | 1.3.6.1.4.1.74.1.30.3.1.1.13 | InetAddressIPv6 | read-only | When the DHCP Type is 'R', this is the primary address the AT&T VPN Gateway devices uses to relay DHCP requests. |
| ADR ngvlIPv6LanAddr | 1.3.6.1.4.1.74.1.30.3.1.1.14 | InetAddressIPv6 | read-only | This is the IPv6 LAN address for the device on the VLAN. |
| I32 ngvlIPv6LanPrefix | 1.3.6.1.4.1.74.1.30.3.1.1.15 | Integer32 | read-only | This is the IPv6 LAN prefix for the device on the VLAN. |
| INT ngvlSpeedCurrent | 1.3.6.1.4.1.74.1.30.3.1.1.16 | INTEGER | read-only | This is the current speed in use on the VLAN Ethernet interfaces. This is helpful to determine what was chosen if the speed was set to auto negotiate. If the VLAN Ethernet speed is configured for auto negotiation then the negotiated speed will be reported. If the VLAN Ethernet speed is configured for auto negotiation and there is no link then noLink will be reported. If the VLAN Ethernet speed is configured for a specific speed that speed will be reported. |
| ngVrrpInfo | 1.3.6.1.4.1.74.1.30.4 | |||
| ngVrrpTable | 1.3.6.1.4.1.74.1.30.4.1 | not-accessible | The (conceptual) table of VRRPs on the device. An entry shall be placed in the storage table for each VRRP. | |
| ngVrrpEntry | 1.3.6.1.4.1.74.1.30.4.1.1 | not-accessible | A (conceptual) entry for one logical VRRP area on the host. | |
| I32 ngvrIndex | 1.3.6.1.4.1.74.1.30.4.1.1.1 | Integer32 | not-accessible | A unique value for each logical VRRP contained by the device. |
| STR ngvrIface | 1.3.6.1.4.1.74.1.30.4.1.1.2 | DisplayString | read-only | The interface associated with this VRRP. |
| I32 ngvrId | 1.3.6.1.4.1.74.1.30.4.1.1.3 | Integer32 | read-only | Virtual router ID. |
| INT ngvrMasterStatus | 1.3.6.1.4.1.74.1.30.4.1.1.4 | INTEGER | read-only | Shows what the status is (master, backup, not active). |
| INT ngvrPriority | 1.3.6.1.4.1.74.1.30.4.1.1.5 | INTEGER | read-only | VRRP_PRIO_OWNER 255 /* priority of the ip owner -- rfc2338.5.3.4 */ VRRP_PRIO_DFL 100 /* default priority -- rfc2338.5.3.4 */ VRRP_PRIO_STOP 0 /* priority to stop -- rfc2338.5.3.4 */ |
| ng3GInfo | 1.3.6.1.4.1.74.1.30.5 | |||
| ng3GTable | 1.3.6.1.4.1.74.1.30.5.1 | not-accessible | The (conceptual) table of 3G cards on the device. An entry shall be placed in the storage table for each 3G card. | |
| ng3GEntry | 1.3.6.1.4.1.74.1.30.5.1.1 | not-accessible | A (conceptual) entry for one logical 3G card area on the host. | |
| I32 ng3gIndex | 1.3.6.1.4.1.74.1.30.5.1.1.1 | Integer32 | not-accessible | A unique value for each logical 3G card contained by the device. |
| I32 ng3gSlotNum | 1.3.6.1.4.1.74.1.30.5.1.1.2 | Integer32 | read-only | The slot the card is plugged into. Returns -1 if no card is found. NOTE: this refers to PCMCIA slots, not USB ports. |
| STR ng3gModemType | 1.3.6.1.4.1.74.1.30.5.1.1.3 | DisplayString | read-only | The modem type. |
| STR ng3gManufacturer | 1.3.6.1.4.1.74.1.30.5.1.1.4 | DisplayString | read-only | The 3G card manufacturer. |
| STR ng3gModel | 1.3.6.1.4.1.74.1.30.5.1.1.5 | DisplayString | read-only | The 3G card model. |
| STR ng3gRevision | 1.3.6.1.4.1.74.1.30.5.1.1.6 | DisplayString | read-only | The 3G card revision. |
| STR ng3gID | 1.3.6.1.4.1.74.1.30.5.1.1.7 | DisplayString | read-only | Either the IMEI or ESN depending on the card. |
| I32 ng3gSignalStrength | 1.3.6.1.4.1.74.1.30.5.1.1.8 | Integer32 | read-only | Signal Strength at the connect. This value will remain zero if cellBars is non-zero. |
| STR ng3gCarrier | 1.3.6.1.4.1.74.1.30.5.1.1.9 | DisplayString | read-only | Information about the carrier. |
| STR ng3gImsiStatus | 1.3.6.1.4.1.74.1.30.5.1.1.10 | DisplayString | read-only | The IMSI attach status. |
| STR ng3gCellConnNetwork | 1.3.6.1.4.1.74.1.30.5.1.1.11 | DisplayString | read-only | The connected network. |
| STR ng3gPhoneNum | 1.3.6.1.4.1.74.1.30.5.1.1.12 | DisplayString | read-only | The cell phone number. |
| STR ng3gApn | 1.3.6.1.4.1.74.1.30.5.1.1.13 | DisplayString | read-only | The access point name. |
| STR ng3gApnUser | 1.3.6.1.4.1.74.1.30.5.1.1.14 | DisplayString | read-only | The APN userid. Only populated when the access point name exists. |
| STR ng3gApnPassword | 1.3.6.1.4.1.74.1.30.5.1.1.15 | DisplayString | read-only | The APN password. Only populated when the access point name exists. |
| INT ng3gCellModemPresent | 1.3.6.1.4.1.74.1.30.5.1.1.16 | INTEGER | read-only | If the cellular modem is a supported unit that allows the AT&T VPN Gateway to query its current status then this value will indicate whether or not the unit is physically present. Unsupported units will always have a value of 'unknown'. |
| STR ng3gSIMCardNumber | 1.3.6.1.4.1.74.1.30.5.1.1.17 | DisplayString | read-only | The SIM number of the card. |
| INT ng3gDeviceType | 1.3.6.1.4.1.74.1.30.5.1.1.18 | INTEGER | read-only | The type of hardware of the cellular modem. |
| DAT cellCollectionTimeDAT | 1.3.6.1.4.1.74.1.30.5.1.1.19 | DateAndTime | read-only | The date and time the cell stats were collected. Not set if the date and time on the device hasn't been set yet. |
| STR cellConnStatus | 1.3.6.1.4.1.74.1.30.5.1.1.20 | DisplayString | read-only | The current status of the cellular connection. |
| STR cellNetworkTech | 1.3.6.1.4.1.74.1.30.5.1.1.21 | DisplayString | read-only | Cell network technology. |
| STR cellCarrier | 1.3.6.1.4.1.74.1.30.5.1.1.22 | DisplayString | read-only | Cellular carrier. |
| STR cellMCC | 1.3.6.1.4.1.74.1.30.5.1.1.23 | DisplayString | read-only | A mobile country code (MCC) is used in combination with a mobile network code (MNC) (also known as a MCC / MNC tuple) to uniquely identify a mobile phone operator (carrier) using the GSM, UMTS, LTE, and iDEN public land mobile networks as well as some CDMA, TETRA, and satellite mobile networks. |
| STR cellMNC | 1.3.6.1.4.1.74.1.30.5.1.1.24 | DisplayString | read-only | Mobile network code |
| STR cellLAC | 1.3.6.1.4.1.74.1.30.5.1.1.25 | DisplayString | read-only | Tower location area code. |
| STR cellCID | 1.3.6.1.4.1.74.1.30.5.1.1.26 | DisplayString | read-only | A GSM Cell ID (CID) is a generally unique number used to identify each Base transceiver station (BTS) or sector of a BTS within a Location area code (LAC) if not within a GSM network. In some cases the last digit of CID represents cells' Sector ID. A valid CID ranges from 0 to 65535 on GSM and CDMA networks and from 0 to 268435455 on UMTS and LTE networks. |
| I32 cellBars | 1.3.6.1.4.1.74.1.30.5.1.1.27 | Integer32 | read-only | A number indicating the signal strength as a bar count. If this value is non-zero then ng3gSignalStrength will return zero. |
| STR cellRSSI | 1.3.6.1.4.1.74.1.30.5.1.1.28 | DisplayString | read-only | Received signal strength indicator. |
| STR cellECIO | 1.3.6.1.4.1.74.1.30.5.1.1.29 | DisplayString | read-only | EC/IO measurement. |
| STR cellRSRP | 1.3.6.1.4.1.74.1.30.5.1.1.30 | DisplayString | read-only | References LTE signals: Reference Signal Received Power is the average power of resource elements that carry cellular specific reference signals over the entire bandwidth. Valid values : all values are valid. Typical values are between -199 and -85. The larger the number (-85 for instance) the better the signal. |
| STR cellRSRQ | 1.3.6.1.4.1.74.1.30.5.1.1.31 | DisplayString | read-only | References LTE Signals: represents the Cell Quality. |
| STR cellSINR | 1.3.6.1.4.1.74.1.30.5.1.1.32 | DisplayString | read-only | References LTE signals: LTE - The signal-to-interference-plus-noise ratio of the modem. |
| STR cellSNR | 1.3.6.1.4.1.74.1.30.5.1.1.33 | DisplayString | read-only | References LTE signals: The signal-to-noise ratio of the modem. |
| STR cellIface | 1.3.6.1.4.1.74.1.30.5.1.1.34 | DisplayString | read-only | The interface on the device associated with this cell modem. |
| ngTunnelInfo | 1.3.6.1.4.1.74.1.30.6 | |||
| ngTunnelTable | 1.3.6.1.4.1.74.1.30.6.1 | not-accessible | The (conceptual) table of tunnels on the device. An entry shall be placed in the storage table for each tunnel. | |
| ngTunnelEntry | 1.3.6.1.4.1.74.1.30.6.1.1 | not-accessible | A (conceptual) entry for one logical tunnel area on the host. | |
| I32 ngtuIndex | 1.3.6.1.4.1.74.1.30.6.1.1.1 | Integer32 | not-accessible | A unique value for each logical tunnel contained by the device. |
| STR ngtuIpsecIface | 1.3.6.1.4.1.74.1.30.6.1.1.2 | DisplayString | read-only | The ipsec interface associated with the tunnel. |
| INT ngtuAuthState | 1.3.6.1.4.1.74.1.30.6.1.1.3 | INTEGER | read-only | An internal state used to indicate the tunnel's current operation. |
| INT ngtuState | 1.3.6.1.4.1.74.1.30.6.1.1.4 | INTEGER | read-only | An internal state used to indicate the tunnel's status. This state was created because the ngtuAuthState can change while the tunnel is still up. For example, when the clock is being set. This state is always attTunnelUp when the tunnel is up. |
| TIK ngtuDuration | 1.3.6.1.4.1.74.1.30.6.1.1.5 | TimeTicks | read-only | How long the tunnel has been up. |
| IP ngtuEndpoint | 1.3.6.1.4.1.74.1.30.6.1.1.6 | IpAddress | read-only | IP of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up'. |
| INT ngtuEndpointType | 1.3.6.1.4.1.74.1.30.6.1.1.7 | INTEGER | read-only | Type of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up'. |
| INT ngtuBulkEncryptMode | 1.3.6.1.4.1.74.1.30.6.1.1.8 | INTEGER | read-only | Bulk encryption mode. |
| IP ngtuCurrEncryptCeIp | 1.3.6.1.4.1.74.1.30.6.1.1.9 | IpAddress | read-only | Bulk encryption CE address. |
| STR ngtuEspAlg | 1.3.6.1.4.1.74.1.30.6.1.1.10 | DisplayString | read-only | ESP algorithm. |
| STR ngtuAuthAlg | 1.3.6.1.4.1.74.1.30.6.1.1.11 | DisplayString | read-only | AUTH algorithm. |
| STR ngtuCompressionAlg | 1.3.6.1.4.1.74.1.30.6.1.1.12 | DisplayString | read-only | COMPRESSION algorithm. |
| INT ngtuAuthType | 1.3.6.1.4.1.74.1.30.6.1.1.13 | INTEGER | read-only | Indicates the authentication server that will be used by the tunnel endpoint. |
| INT ngtuAuthProt | 1.3.6.1.4.1.74.1.30.6.1.1.14 | INTEGER | read-only | The authentication protocol. |
| INT ngtuReasonCode | 1.3.6.1.4.1.74.1.30.6.1.1.15 | INTEGER | read-only | A numeric value that indicates why an inbound or outbound tunnel came down. The one exception is tnlAlive, which is sent for the tunnel 'alive' message for a tunnel that is still up. |
| INT ngtuServerMgmt | 1.3.6.1.4.1.74.1.30.6.1.1.16 | INTEGER | read-only | AGNS managed or not. |
| INT ngtuTunInitiator | 1.3.6.1.4.1.74.1.30.6.1.1.17 | INTEGER | read-only | What initiated the tunnel. |
| INT ngtuTunMode | 1.3.6.1.4.1.74.1.30.6.1.1.18 | INTEGER | read-only | The tunnel control mode. |
| ADR ngtuIPv6Endpoint | 1.3.6.1.4.1.74.1.30.6.1.1.19 | InetAddressIPv6 | read-only | IPv6 IP of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up' and IPv6 is in use. |
| INT tunCurrAutomation | 1.3.6.1.4.1.74.1.30.6.1.1.20 | INTEGER | read-only | The tunnel automation that is currently in use and whether or not it is currently active. NOTE: Active does not necessarily mean that the tunnel is up. It could mean that the tunnel is up, in the process of coming up, or is in a state where it will be brought up if the right conditions are met. There is no automation for User Initiated mode. |
| INT tunInitVpnCon | 1.3.6.1.4.1.74.1.30.6.1.1.21 | INTEGER | read-only | The tunnel automation (if any) configured for the primary connection in Service Manager. If configured for User Initiated the user can choose to override that setting from the CGI interface and select Persistent or Traffic Initiated instead. |
| INT tunInitVpnBkupCon | 1.3.6.1.4.1.74.1.30.6.1.1.22 | INTEGER | read-only | Similar to tunInitVpnCon except that this controls tunnel automation via the backup connection. |
| STR tunConnectionId | 1.3.6.1.4.1.74.1.30.6.1.1.23 | DisplayString | accessible-for-notify | The tunnel connection ID is a unique value assigned to each instance of a tunnel. It is used to associate the tunnel up, tunnel alive, and tunnel down traps together. When a tunnel goes down and is then re-established it will be assigned a new tunnel connection ID. This is the same value reported by ngevTunConnectionId in traps. |
| STR tunName | 1.3.6.1.4.1.74.1.30.6.1.1.24 | DisplayString | accessible-for-notify | The name associated with this tunnel. Note that the name will be 'settings' if multi-tunnel is disabled. |
| INT tunDirection | 1.3.6.1.4.1.74.1.30.6.1.1.25 | INTEGER | read-only | Indicates whether this is an inbound or outbound tunnel. |
| ngCosInfo | 1.3.6.1.4.1.74.1.30.7 | |||
| INT ngcoEnabled | 1.3.6.1.4.1.74.1.30.7.1 | INTEGER | read-only | Indicates if COS is enabled or not. As of version 6.2 bandwidth testing can be active without COS being enabled. When that happens ngcoEnabled will return zero (notActive) but ngcoNextTestTimeDAT will not return January 1 year 0 time 0 for the time. |
| STR ngcoNextTestTime | 1.3.6.1.4.1.74.1.30.7.2 | DisplayString | read-only | When the next bandwidth test is scheduled to run. MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when no test is scheduled. The time returned is the local time on the AT&T VPN Gateway. To determine how the AT&T VPN Gateway's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngcoNextTestTimeDAT. |
| I32 ngcoWanMtu | 1.3.6.1.4.1.74.1.30.7.3 | Integer32 | read-only | Current WAN interface MTU value. |
| U32 ngcoCurUpstreamBandw | 1.3.6.1.4.1.74.1.30.7.4 | Unsigned32 | read-only | Current upstream bandwidth high water mark in use. |
| U32 ngcoCurDownstreamBandw | 1.3.6.1.4.1.74.1.30.7.5 | Unsigned32 | read-only | Current downstream bandwidth high water mark in use. |
| DAT ngcoNextTestTimeDAT | 1.3.6.1.4.1.74.1.30.7.6 | DateAndTime | read-only | When the next bandwidth test is scheduled to run. Returns January 1 year 0 time 0 when no test is scheduled. NOTE: This entry replaces ngcoNextTestTime. |
| DAT ngcoLastTestTimeDAT | 1.3.6.1.4.1.74.1.30.7.7 | DateAndTime | read-only | The date and time of when the last bandwidth test was performed. NOTE: The date and time of high water marks retained after a reboot will return January 1 year 0 time 0 for the time. |
| U32 ngcoLastUpstreamResult | 1.3.6.1.4.1.74.1.30.7.8 | Unsigned32 | read-only | The upstream bandwidth measured when the last bandwidth test was performed. |
| U32 ngcoLastDownstreamResult | 1.3.6.1.4.1.74.1.30.7.9 | Unsigned32 | read-only | The downstream bandwidth measured when the last bandwidth test was performed. |
| attVpnGatewayMIB | 1.3.6.1.4.1.74.1.30.8 | The MIB module for the AT&T VPN Gateway. | ||
| ngMIBConformance | 1.3.6.1.4.1.74.1.30.8.1 | |||
| ngMIBCompliances | 1.3.6.1.4.1.74.1.30.8.1.1 | |||
| ngBasicComplianceRev | 1.3.6.1.4.1.74.1.30.8.1.1.1 | The compliance statement for AT&T VPN Gateway entities which implement this MIB module. | ||
| ngMIBGroups | 1.3.6.1.4.1.74.1.30.8.1.2 | |||
| nghwGroup | 1.3.6.1.4.1.74.1.30.8.1.2.1 | The hardware group. | ||
| ngifGroup | 1.3.6.1.4.1.74.1.30.8.1.2.2 | The interface group. | ||
| ngvlGroup | 1.3.6.1.4.1.74.1.30.8.1.2.3 | The VLAN group. | ||
| ngvrGroup | 1.3.6.1.4.1.74.1.30.8.1.2.4 | The VRRP group. | ||
| ng3gGroup | 1.3.6.1.4.1.74.1.30.8.1.2.5 | The 3G group. | ||
| ngtuGroup | 1.3.6.1.4.1.74.1.30.8.1.2.6 | The tunnel group. | ||
| ngcoGroup | 1.3.6.1.4.1.74.1.30.8.1.2.7 | The COS group. | ||
| ngfwGroup | 1.3.6.1.4.1.74.1.30.8.1.2.8 | The firewall group. | ||
| ngrmGroup | 1.3.6.1.4.1.74.1.30.8.1.2.9 | The Rogue MAC group. | ||
| ngdiGroup | 1.3.6.1.4.1.74.1.30.8.1.2.10 | The dial group. | ||
| ngdhlGroup | 1.3.6.1.4.1.74.1.30.8.1.2.11 | The DHCP leases group. | ||
| ngCapPorGroup | 1.3.6.1.4.1.74.1.30.8.1.2.12 | The Captive Portal group. | ||
| attInbTunGroup | 1.3.6.1.4.1.74.1.30.8.1.2.13 | The Inbound Tunnel group. | ||
| attInbTunNetGroup | 1.3.6.1.4.1.74.1.30.8.1.2.14 | The Inbound Tunnel Network group. | ||
| ngEvents | 1.3.6.1.4.1.74.1.30.8.2 | |||
| ngEventNotification | 1.3.6.1.4.1.74.1.30.8.2.0 | |||
| NTF ngevIpConntrackTable | 1.3.6.1.4.1.74.1.30.8.2.0.1 | Sent if the Firewall Connection table reaches the specified threshold. | ||
| NTF ngevIpConntrackTableFull | 1.3.6.1.4.1.74.1.30.8.2.0.2 | Indicates the firewall Connection table has reached capacity. | ||
| NTF ngevExcessiveDial | 1.3.6.1.4.1.74.1.30.8.2.0.3 | The device has been in dial backup longer than the allowed threshold. | ||
| NTF ngevActiveWanIpChanged | 1.3.6.1.4.1.74.1.30.8.2.0.4 | The IP address associated with the active WAN interface has changed. For example, dial backup was initiated because WAN connectivity was lost. Another example is that a PPPoE connection changed its IP address. | ||
| NTF ngevRogueMacDetected | 1.3.6.1.4.1.74.1.30.8.2.0.5 | The unauthorized MAC detection feature is enabled and an unauthorized MAC address was detected. | ||
| NTF ngevRogueMacNoFile | 1.3.6.1.4.1.74.1.30.8.2.0.6 | The unauthorized MAC detection feature is enabled and the authorized MAC file doesn't exist. | ||
| NTF ngevNoTeps | 1.3.6.1.4.1.74.1.30.8.2.0.7 | The AT&T VPN Gateway cannot bring up a tunnel to any of the tunnel endpoints. | ||
| NTF ngevDeviceDiscoOrNotFound | 1.3.6.1.4.1.74.1.30.8.2.0.8 | Sent if the AT&T VPN Gateway profile is not found. If the AT&T VPN Gateway goes too long without finding its device profile then the device will switch its status to discontinued, which will also trigger a trap/inform. | ||
| NTF ngevTunnelUp | 1.3.6.1.4.1.74.1.30.8.2.0.9 | Information about the results of a tunnel connection attempt. | ||
| NTF ngevTunnelDown | 1.3.6.1.4.1.74.1.30.8.2.0.10 | Information about a tunnel disconnect. The one exception is a tunnel 'alive' message, which is sent for a tunnel that is still up. Tunnel 'alive' messages have a ngtuReasonCode of tnlAlive. | ||
| NTF ngevDialAutotestFailure | 1.3.6.1.4.1.74.1.30.8.2.0.11 | The Dial Autotest (and all specified retries) failed. | ||
| NTF ngevDeviceReboot | 1.3.6.1.4.1.74.1.30.8.2.0.12 | Sent when the device reboots. Requestor IP will be set to loopback if an automated process caused the reboot. | ||
| NTF ngevDeviceShutdown | 1.3.6.1.4.1.74.1.30.8.2.0.13 | Sent when the device shuts down. | ||
| NTF ngevSshLogin | 1.3.6.1.4.1.74.1.30.8.2.0.14 | Sent when a user accesses the device via SSH. | ||
| NTF ngevDhcpPoolExhausted | 1.3.6.1.4.1.74.1.30.8.2.0.15 | Sent when a VLAN's DHCP pool is full. | ||
| NTF ngevForTestingOnly | 1.3.6.1.4.1.74.1.30.8.2.0.16 | Only for use by QA and development for testing. | ||
| NTF ngevSecondaryAuthAttempt | 1.3.6.1.4.1.74.1.30.8.2.0.17 | Sent when a secondary login attempt occurs. Secondary logins are performed when someone tries to ssh into the AT&T VPN Gateway. | ||
| NTF ngevSwitchUseridAttempt | 1.3.6.1.4.1.74.1.30.8.2.0.18 | Sent when a user who is ssh'ed into the AT&T VPN Gateway tries to switch to another userid. | ||
| NTF ngev8200VPortDown | 1.3.6.1.4.1.74.1.30.8.2.0.19 | Sent when either port 7 or 8 is determined to be not active. Only used by the AT&T VPN Gateway 8200V. | ||
| NTF ngevCellModemRequired | 1.3.6.1.4.1.74.1.30.8.2.0.20 | Sent when either the AT&T VPN Gateway boots without a cell modem present or when the AT&T VPN Gateway detects that the cell modem has been removed. The cellular modem must be a supported unit that allows the AT&T VPN Gateway to query its current status. | ||
| NTF evVrrpStateChange | 1.3.6.1.4.1.74.1.30.8.2.0.21 | Sent when there is a VRRP state change. | ||
| NTF evDualWanIfaceProblem | 1.3.6.1.4.1.74.1.30.8.2.0.22 | Sent when the AT&T VPN Gateway is configured to also use the second WAN port as Internet Primary and one of the interfaces could not be brought up. | ||
| NTF evOOBCableRequired | 1.3.6.1.4.1.74.1.30.8.2.0.23 | Optional USB cables allow out of bound (OOB) access to the AT&T VPN Gateway. The number of OOB cables expected to be plugged into the AT&T VPN Gateway is controlled by a setting in Service Manager. This event is sent when either the AT&T VPN Gateway boots without the expected number of cables present, when the AT&T VPN Gateway detects that a cable was present but has been removed, or when all missing cables are returned. | ||
| NTF evTunConfigChanged | 1.3.6.1.4.1.74.1.30.8.2.0.24 | Sent when the tunnel configuration has changed. All tunnels (if any) are restarted when this occurs. | ||
| NTF evDataUsageReport | 1.3.6.1.4.1.74.1.30.8.2.0.25 | Reporting of average bandwidth along with high water mark calculations. | ||
| NTF evPingTestResult | 1.3.6.1.4.1.74.1.30.8.2.0.26 | Sent to indicate the result of a ping test. | ||
| NTF evNoIPinCDPool | 1.3.6.1.4.1.74.1.30.8.2.0.27 | Sent to indicate that there are no available IP addresses in the customer direct pool. | ||
| NTF evMaxInbTun | 1.3.6.1.4.1.74.1.30.8.2.0.28 | Sent to indicate that there are no inbound tunnels available. | ||
| NTF evReportDualWanIP | 1.3.6.1.4.1.74.1.30.8.2.0.29 | Sent to report on the IP addresses in use when both Dual WAN interfaces are up. | ||
| ngEventObjects | 1.3.6.1.4.1.74.1.30.8.2.1 | |||
| STR ngevMac | 1.3.6.1.4.1.74.1.30.8.2.1.1 | DisplayString | accessible-for-notify | The MAC address in Service Manager this device is registered under. |
| STR ngevRogueMac | 1.3.6.1.4.1.74.1.30.8.2.1.2 | DisplayString | accessible-for-notify | The MAC address of the unauthorized machine detected when MAC monitoring is enabled. |
| IP ngevActiveWanIp | 1.3.6.1.4.1.74.1.30.8.2.1.3 | IpAddress | accessible-for-notify | The IP address of the active WAN interface. When viewing the output of the SNMP tree this can be determined from the interface statistics. However, for traps the active WAN interface might not be used to send the trap (i.e. it could be down the tunnel. Set to zero if not used. |
| I32 ngevIpConntrackMaxPercentage | 1.3.6.1.4.1.74.1.30.8.2.1.4 | Integer32 | accessible-for-notify | An alert will be sent when the ip_conntrack table is within this percentage of the maximum. |
| I32 ngevIpConntrackCurrentPercentage | 1.3.6.1.4.1.74.1.30.8.2.1.5 | Integer32 | accessible-for-notify | The ip_conntrack table is currently at this percentage of the maximum. |
| I32 ngevTimeInDial | 1.3.6.1.4.1.74.1.30.8.2.1.6 | Integer32 | accessible-for-notify | The number of minutes the device has been connected via dial. |
| INT ngevQueryProblem | 1.3.6.1.4.1.74.1.30.8.2.1.7 | INTEGER | accessible-for-notify | Used to indicate what type of problem is happening with the device's status. profileNotFound means that a profile for the device was not found on an AT&T Administration Server in any region. discontinuingTheDevice means that the device has gone too long without having a valid profile in any region. bandwNoResults means that a bandwidth test failed and no previous bandwidth test results have been found, which results in the device being marked as discontinued until a bandwidth test works. |
| STR ngevTunConnectionId | 1.3.6.1.4.1.74.1.30.8.2.1.8 | DisplayString | accessible-for-notify | The tunnel connection ID is a unique value assigned to each instance of a tunnel. It is used to associate the tunnel up, tunnel alive, and tunnel down traps together. When a tunnel goes down and is then re-established it will be assigned a new tunnel connection ID. |
| DAT ngevTunnelDateAndTime | 1.3.6.1.4.1.74.1.30.8.2.1.9 | DateAndTime | accessible-for-notify | The timestamp from when the tunnel came up, tried to come up, or came down. |
| INT ngevConnectionType | 1.3.6.1.4.1.74.1.30.8.2.1.10 | INTEGER | accessible-for-notify | Indicates whether the tunnel is via broadband or dial. |
| STR ngevAccount | 1.3.6.1.4.1.74.1.30.8.2.1.11 | DisplayString | accessible-for-notify | In the tunnel up/down trap it is the customer account used to start the tunnel. In the secondary auth attempt trap it is the account used for the login attempt. |
| STR ngevUserid | 1.3.6.1.4.1.74.1.30.8.2.1.12 | DisplayString | accessible-for-notify | In the tunnel up/down trap it is the customer userid used to start the tunnel. In the secondary auth attempt trap it is the userid used for the login attempt. |
| STR ngevTunConReason | 1.3.6.1.4.1.74.1.30.8.2.1.13 | DisplayString | accessible-for-notify | String that shows a message that explains the results of a tunnel connection attempt. |
| STR ngevDialTestFailReason | 1.3.6.1.4.1.74.1.30.8.2.1.14 | DisplayString | accessible-for-notify | String that shows why the dial test failed. |
| IP ngevSshSourceIp | 1.3.6.1.4.1.74.1.30.8.2.1.15 | IpAddress | accessible-for-notify | The IP address of the client that ssh'ed into the device. |
| IP ngevRequestorIp | 1.3.6.1.4.1.74.1.30.8.2.1.16 | IpAddress | accessible-for-notify | The IP address of the machine that initiated a particular request (reboot, shutdown, secondary auth attempt, etc.). Will be set to loopback if an automated process caused the reboot. |
| INT ngevDialTestFailCategory | 1.3.6.1.4.1.74.1.30.8.2.1.17 | INTEGER | accessible-for-notify | Shows what type of category the dial test failure would be put in. For example, a busy signal would be a warning but a bad password would be an error. |
| IP ngevRogueIp | 1.3.6.1.4.1.74.1.30.8.2.1.18 | IpAddress | accessible-for-notify | The IP address of the unauthorized machine detected when MAC monitoring is enabled. Set to zero if not used. |
| STR ngevRogueInterface | 1.3.6.1.4.1.74.1.30.8.2.1.19 | DisplayString | accessible-for-notify | The interface of the unauthorized machine detected when MAC monitoring is enabled. |
| STR ngevTrapDescription | 1.3.6.1.4.1.74.1.30.8.2.1.20 | DisplayString | accessible-for-notify | For MAC monitoring this is the Service Manager description field. Other traps may use this field for other purposes. |
| INT ngevLoginResult | 1.3.6.1.4.1.74.1.30.8.2.1.21 | INTEGER | accessible-for-notify | Specifies the result of the secondary login attempt when someone tries to ssh into the AT&T VPN Gateway. |
| STR ngevNewLocalID | 1.3.6.1.4.1.74.1.30.8.2.1.22 | DisplayString | accessible-for-notify | The userid that the user became after their secondary login attempt was successful. Secondary logins are performed when someone tries to ssh into the AT&T VPN Gateway. The userid that the user became (or tried to become) for their switch user attempt. |
| STR ngevOldLocalID | 1.3.6.1.4.1.74.1.30.8.2.1.23 | DisplayString | accessible-for-notify | The userid that was in use when the user made their switch user attempt. |
| TIK ngevMaxTimeInDialUntilAlert | 1.3.6.1.4.1.74.1.30.8.2.1.24 | TimeTicks | accessible-for-notify | The max number of minutes the device can be connected via dial without a trap being sent for excessive dial. Once this maximum is reached a trap will be sent. |
| I32 ngevPortDown | 1.3.6.1.4.1.74.1.30.8.2.1.25 | Integer32 | accessible-for-notify | An individual port that is currently not active. Only used by the AT&T VPN Gateway 8200V. |
| ADR ngevIPv6ActiveWanIp | 1.3.6.1.4.1.74.1.30.8.2.1.26 | InetAddressIPv6 | accessible-for-notify | The IP address of the active IPv6 WAN interface. When viewing the output of the SNMP tree this can be determined from the interface statistics. However, for traps the active WAN interface might not be used to send the trap (i.e. it could be down the tunnel. Set to zero if not used. |
| ADR ngevIPv6RogueIp | 1.3.6.1.4.1.74.1.30.8.2.1.27 | InetAddressIPv6 | accessible-for-notify | The IPv6 IP address of the unauthorized machine detected when MAC monitoring is enabled. Set to zero if not used. |
| ADR ngevIPv6RequestorIp | 1.3.6.1.4.1.74.1.30.8.2.1.28 | InetAddressIPv6 | accessible-for-notify | The IPv6 IP address of the machine that initiated a particular request (reboot, shutdown, secondary auth attempt, etc.). Will be set to loopback if an automated process caused the reboot. |
| DAT ngevCardNotFoundTime | 1.3.6.1.4.1.74.1.30.8.2.1.29 | DateAndTime | accessible-for-notify | The timestamp that indicates when the AT&T VPN Gateway noted that the required cellular card was missing. |
| IP ngevVPNServiceIPv4Address | 1.3.6.1.4.1.74.1.30.8.2.1.30 | IpAddress | accessible-for-notify | The VPN Service Address assigned for this tunnel connetion. Will be not set if this is an IPv6 tunnel or the tunnel did not come up. |
| ADR ngevVPNServiceIPv6Address | 1.3.6.1.4.1.74.1.30.8.2.1.31 | InetAddressIPv6 | accessible-for-notify | The VPN Service Address assigned for this tunnel connetion. Will be not set if this is an IPv4 tunnel or the tunnel did not come up. |
| INT ngevTunConReasonNUM | 1.3.6.1.4.1.74.1.30.8.2.1.32 | INTEGER | read-only | A numeric value that indicates the results of an inbound or outbound tunnel connection attempt. |
| STR evIface | 1.3.6.1.4.1.74.1.30.8.2.1.33 | DisplayString | accessible-for-notify | The interface in question for this event. |
| DAT evNotFoundTime | 1.3.6.1.4.1.74.1.30.8.2.1.34 | DateAndTime | accessible-for-notify | The timestamp that indicates when the AT&T VPN Gateway noted that the item in question was missing. |
| DAT evTrapCreatedTime | 1.3.6.1.4.1.74.1.30.8.2.1.35 | DateAndTime | accessible-for-notify | The timestamp that indicates when the trap was actually generated. If informs are in use and the server is temporarily not reachable it could be a long time before the inform is actually received. |
| INT evDualWanProb | 1.3.6.1.4.1.74.1.30.8.2.1.36 | INTEGER | accessible-for-notify | Used to help indicate why IPv4 WAN2 could not be brought up when configured for Dual WAN. The generic 'dwTrapGeneralErr' is used when a specific reason isn't available. 'dwTrapNone' means that there was no error. |
| INT evDualWanV6Prob | 1.3.6.1.4.1.74.1.30.8.2.1.37 | INTEGER | accessible-for-notify | Used to help indicate why IPv6 WAN2 could not be brought up when configured for Dual WAN. The generic 'dwTrapGeneralErr' is used when a specific reason isn't available. 'dwTrapNone' means that there was no error. |
| I32 evFoundOOB | 1.3.6.1.4.1.74.1.30.8.2.1.38 | Integer32 | accessible-for-notify | How many OOB cables were detected when at least one was found to be missing. |
| I32 evExpectedOOB | 1.3.6.1.4.1.74.1.30.8.2.1.39 | Integer32 | accessible-for-notify | How many OOB cables were expected when at least one was found to be missing. |
| INT evResult | 1.3.6.1.4.1.74.1.30.8.2.1.40 | INTEGER | accessible-for-notify | Generic field to indicate a result. |
| IP evSrcV4 | 1.3.6.1.4.1.74.1.30.8.2.1.41 | IpAddress | accessible-for-notify | Generic source IPv4 address. |
| IP evDestV4 | 1.3.6.1.4.1.74.1.30.8.2.1.42 | IpAddress | accessible-for-notify | Generic destination IPv4 address. |
| ADR evSrcV6 | 1.3.6.1.4.1.74.1.30.8.2.1.43 | InetAddressIPv6 | accessible-for-notify | Generic source IPv6 address. |
| ADR evDestV6 | 1.3.6.1.4.1.74.1.30.8.2.1.44 | InetAddressIPv6 | accessible-for-notify | Generic destination IPv6 address. |
| I32 evResponseMax | 1.3.6.1.4.1.74.1.30.8.2.1.45 | Integer32 | accessible-for-notify | Generic field to indicate how long a test waited for a response. |
| I32 evFailureCount | 1.3.6.1.4.1.74.1.30.8.2.1.46 | Integer32 | accessible-for-notify | Generic field to indicate how many failures occurred before this event was generated. |
| STR evDescription | 1.3.6.1.4.1.74.1.30.8.2.1.47 | DisplayString | accessible-for-notify | Generic field for description. |
| INT evSendTrapWhen | 1.3.6.1.4.1.74.1.30.8.2.1.48 | INTEGER | accessible-for-notify | Generic field used to indicate when to send a trap after a test is performed. |
| IP evWan1IPv4IP | 1.3.6.1.4.1.74.1.30.8.2.1.49 | IpAddress | accessible-for-notify | Field used to report on the IP of the first interface if it is using IPv4. |
| STR evWan1IPv4Name | 1.3.6.1.4.1.74.1.30.8.2.1.50 | DisplayString | accessible-for-notify | Field used to report on the name of the first interface if it is using IPv4. |
| ADR evWan1IPv6IP | 1.3.6.1.4.1.74.1.30.8.2.1.51 | InetAddressIPv6 | accessible-for-notify | Generic field used to report on the IP of the first interface if it is using IPv6. |
| STR evWan1IPv6Name | 1.3.6.1.4.1.74.1.30.8.2.1.52 | DisplayString | accessible-for-notify | Field used to report on the name of the first interface if it is using IPv6. |
| IP evWan2IPv4IP | 1.3.6.1.4.1.74.1.30.8.2.1.53 | IpAddress | accessible-for-notify | Generic field used to report on the IP of the second interface if it is using IPv4. |
| STR evWan2IPv4Name | 1.3.6.1.4.1.74.1.30.8.2.1.54 | DisplayString | accessible-for-notify | Field used to report on the name of the second interface if it is using IPv4. |
| ADR evWan2IPv6IP | 1.3.6.1.4.1.74.1.30.8.2.1.55 | InetAddressIPv6 | accessible-for-notify | Generic field used to report on the IP of the second interface if it is using IPv6. |
| STR evWan2IPv6Name | 1.3.6.1.4.1.74.1.30.8.2.1.56 | DisplayString | accessible-for-notify | Field used to report on the name of the second interface if it is using IPv6. |
| INT evNatTEnabled | 1.3.6.1.4.1.74.1.30.8.2.1.57 | INTEGER | accessible-for-notify | Tunnel field that indicates whether or not Nat-T is in use. |
| STR evESPAlgorithm | 1.3.6.1.4.1.74.1.30.8.2.1.58 | DisplayString | accessible-for-notify | Tunnel field that indicates the ESP Algorithm. |
| STR evAuthAlgorithm | 1.3.6.1.4.1.74.1.30.8.2.1.59 | DisplayString | accessible-for-notify | Tunnel field that indicates the Auth Algorithm. |
| STR evCompressionAlgorithm | 1.3.6.1.4.1.74.1.30.8.2.1.60 | DisplayString | accessible-for-notify | Tunnel field that indicates the (optional) Compression Algorithm. |
| ngEventConformance | 1.3.6.1.4.1.74.1.30.8.2.2 | |||
| ngEventCompliances | 1.3.6.1.4.1.74.1.30.8.2.2.1 | |||
| ngevBasicComplianceRev | 1.3.6.1.4.1.74.1.30.8.2.2.1.1 | The compliance statement for AT&T VPN Gateway entities which implement this MIB module. | ||
| ngEventGroups | 1.3.6.1.4.1.74.1.30.8.2.2.2 | |||
| ngevNotificationsGroup | 1.3.6.1.4.1.74.1.30.8.2.2.2.1 | The event notifications | ||
| ngevObjectsGroup | 1.3.6.1.4.1.74.1.30.8.2.2.2.2 | The event ojects. | ||
| ngEventDataUsageObjectsGroup | 1.3.6.1.4.1.74.1.30.8.2.2.2.3 | The event ojects used only for data usage statistics. | ||
| ngEventDataUsageObjects | 1.3.6.1.4.1.74.1.30.8.2.3 | |||
| U32 evDataUpHwm | 1.3.6.1.4.1.74.1.30.8.2.3.1 | Unsigned32 | read-only | The upstream high water mark to be used for the calculations. |
| U32 evDataDownHwm | 1.3.6.1.4.1.74.1.30.8.2.3.2 | Unsigned32 | read-only | The downstream high water mark to be used for the calculations. |
| U32 evDataUp1 | 1.3.6.1.4.1.74.1.30.8.2.3.3 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown1 | 1.3.6.1.4.1.74.1.30.8.2.3.4 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp2 | 1.3.6.1.4.1.74.1.30.8.2.3.5 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown2 | 1.3.6.1.4.1.74.1.30.8.2.3.6 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp3 | 1.3.6.1.4.1.74.1.30.8.2.3.7 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown3 | 1.3.6.1.4.1.74.1.30.8.2.3.8 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp4 | 1.3.6.1.4.1.74.1.30.8.2.3.9 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown4 | 1.3.6.1.4.1.74.1.30.8.2.3.10 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp5 | 1.3.6.1.4.1.74.1.30.8.2.3.11 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown5 | 1.3.6.1.4.1.74.1.30.8.2.3.12 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp6 | 1.3.6.1.4.1.74.1.30.8.2.3.13 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown6 | 1.3.6.1.4.1.74.1.30.8.2.3.14 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp7 | 1.3.6.1.4.1.74.1.30.8.2.3.15 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown7 | 1.3.6.1.4.1.74.1.30.8.2.3.16 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp8 | 1.3.6.1.4.1.74.1.30.8.2.3.17 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown8 | 1.3.6.1.4.1.74.1.30.8.2.3.18 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp9 | 1.3.6.1.4.1.74.1.30.8.2.3.19 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown9 | 1.3.6.1.4.1.74.1.30.8.2.3.20 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp10 | 1.3.6.1.4.1.74.1.30.8.2.3.21 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown10 | 1.3.6.1.4.1.74.1.30.8.2.3.22 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp11 | 1.3.6.1.4.1.74.1.30.8.2.3.23 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown11 | 1.3.6.1.4.1.74.1.30.8.2.3.24 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| U32 evDataUp12 | 1.3.6.1.4.1.74.1.30.8.2.3.25 | Unsigned32 | read-only | Average upstream bandwidth measured over a certain time period. |
| U32 evDataDown12 | 1.3.6.1.4.1.74.1.30.8.2.3.26 | Unsigned32 | read-only | Average downstream bandwidth measured over a certain time period. |
| ngPlatforms | 1.3.6.1.4.1.74.1.30.8.3 | |||
| attVpnGateway8200 | 1.3.6.1.4.1.74.1.30.8.3.1 | |||
| attVpnGateway8300 | 1.3.6.1.4.1.74.1.30.8.3.2 | |||
| attVpnGatewayVM | 1.3.6.1.4.1.74.1.30.8.3.3 | |||
| ngFirewallInfo | 1.3.6.1.4.1.74.1.30.9 | |||
| ngFirewallTable | 1.3.6.1.4.1.74.1.30.9.1 | not-accessible | The (conceptual) table of firewall tables on the device. An entry shall be placed in the storage table for each table. | |
| ngFirewallTableEntry | 1.3.6.1.4.1.74.1.30.9.1.1 | not-accessible | A (conceptual) entry for one logical firewall table area on the host. | |
| I32 ngfwTableIndex | 1.3.6.1.4.1.74.1.30.9.1.1.1 | Integer32 | not-accessible | A unique value for each logical firewall table contained by the device. |
| STR ngfwTableName | 1.3.6.1.4.1.74.1.30.9.1.1.2 | DisplayString | read-only | The name of this table. |
| I32 ngfwTableNumberOfChains | 1.3.6.1.4.1.74.1.30.9.1.1.3 | Integer32 | read-only | The number of chains in this particular table. |
| ngFirewallChainTable | 1.3.6.1.4.1.74.1.30.9.2 | not-accessible | The (conceptual) chain of firewall chains on the device. An entry shall be placed in the storage chain for each chain. | |
| ngFirewallChainEntry | 1.3.6.1.4.1.74.1.30.9.2.1 | not-accessible | A (conceptual) entry for one logical firewall chain area on the host. | |
| I32 ngfwChainIndex | 1.3.6.1.4.1.74.1.30.9.2.1.1 | Integer32 | not-accessible | A unique value for each logical firewall chain contained by the device. |
| I32 ngfwChainTableIndex | 1.3.6.1.4.1.74.1.30.9.2.1.2 | Integer32 | read-only | Shows what table this chain belongs to. Corresponds to ngfwTableIndex in ngFirewallTable. |
| STR ngfwChainName | 1.3.6.1.4.1.74.1.30.9.2.1.3 | DisplayString | read-only | The name of this chain. |
| I32 ngfwChainsNumberOfRules | 1.3.6.1.4.1.74.1.30.9.2.1.4 | Integer32 | read-only | The number of rules in this particular chain. |
| ngFirewallRuleTable | 1.3.6.1.4.1.74.1.30.9.3 | not-accessible | The (conceptual) table of firewall rules on the device. An entry shall be placed in the storage rule for each rule. | |
| ngFirewallRuleEntry | 1.3.6.1.4.1.74.1.30.9.3.1 | not-accessible | A (conceptual) entry for one logical firewall rule area on the host. | |
| I32 ngfwRuleIndex | 1.3.6.1.4.1.74.1.30.9.3.1.1 | Integer32 | not-accessible | A unique value for each logical firewall rule contained by the device. |
| I32 ngfwRuleTableIndex | 1.3.6.1.4.1.74.1.30.9.3.1.2 | Integer32 | read-only | Shows what table this rule belongs to. Corresponds to ngfwTableIndex in ngFirewallTable. |
| I32 ngfwRuleChainIndex | 1.3.6.1.4.1.74.1.30.9.3.1.3 | Integer32 | read-only | Shows what chain this rule belongs to. Corresponds to ngfwChainIndex in ngFirewallChainTable. |
| U32 ngfwRulePackets | 1.3.6.1.4.1.74.1.30.9.3.1.4 | Unsigned32 | read-only | Total packets for this rule. |
| U32 ngfwRuleBytes | 1.3.6.1.4.1.74.1.30.9.3.1.5 | Unsigned32 | read-only | Total bytes for this rule. |
| STR ngfwRuleTarget | 1.3.6.1.4.1.74.1.30.9.3.1.6 | DisplayString | read-only | The rule target. |
| STR ngfwRuleProtocol | 1.3.6.1.4.1.74.1.30.9.3.1.7 | DisplayString | read-only | The rule protocol. |
| STR ngfwRuleInIface | 1.3.6.1.4.1.74.1.30.9.3.1.8 | DisplayString | read-only | The rule input interface. |
| STR ngfwRuleOutIface | 1.3.6.1.4.1.74.1.30.9.3.1.9 | DisplayString | read-only | The rule output interface. |
| IP ngfwRuleSrcIp | 1.3.6.1.4.1.74.1.30.9.3.1.10 | IpAddress | read-only | The rule source IP. |
| I32 ngfwRuleSrcMask | 1.3.6.1.4.1.74.1.30.9.3.1.11 | Integer32 | read-only | The rule source mask in CIDR-compliant format. |
| IP ngfwRuleDstIp | 1.3.6.1.4.1.74.1.30.9.3.1.12 | IpAddress | read-only | The rule destination IP. |
| I32 ngfwRuleDstMask | 1.3.6.1.4.1.74.1.30.9.3.1.13 | Integer32 | read-only | The rule destination mask in CIDR-compliant format. |
| STR ngfwRuleMisc | 1.3.6.1.4.1.74.1.30.9.3.1.14 | DisplayString | read-only | The rule MISC section. |
| I32 ngfwIpConntrackNumEntries | 1.3.6.1.4.1.74.1.30.9.4 | Integer32 | read-only | The number entries in the ip_conntrack file. |
| I32 ngfwIpConntrackMaxNumEntries | 1.3.6.1.4.1.74.1.30.9.5 | Integer32 | read-only | The maximum number of entries in the ip_conntrack file. |
| ngIPv6FirewallTable | 1.3.6.1.4.1.74.1.30.9.6 | not-accessible | The (conceptual) table of IPv6 firewall tables on the device. An entry shall be placed in the storage table for each table. | |
| ngIPv6FirewallTableEntry | 1.3.6.1.4.1.74.1.30.9.6.1 | not-accessible | A (conceptual) entry for one logical IPv6 firewall table area on the host. | |
| I32 ngfwIPv6TableIndex | 1.3.6.1.4.1.74.1.30.9.6.1.1 | Integer32 | not-accessible | A unique value for each logical IPv6 firewall table contained by the device. |
| STR ngfwIPv6TableName | 1.3.6.1.4.1.74.1.30.9.6.1.2 | DisplayString | read-only | The name of this table. |
| I32 ngfwIPv6TableNumberOfChains | 1.3.6.1.4.1.74.1.30.9.6.1.3 | Integer32 | read-only | The number of chains in this particular table. |
| ngIPv6FirewallChainTable | 1.3.6.1.4.1.74.1.30.9.7 | not-accessible | The (conceptual) chain of IPv6 firewall chains on the device. An entry shall be placed in the storage chain for each chain. | |
| ngIPv6FirewallChainEntry | 1.3.6.1.4.1.74.1.30.9.7.1 | not-accessible | A (conceptual) entry for one logical IPv6 firewall chain area on the host. | |
| I32 ngfwIPv6ChainIndex | 1.3.6.1.4.1.74.1.30.9.7.1.1 | Integer32 | not-accessible | A unique value for each logical IPv6 firewall chain contained by the device. |
| I32 ngfwIPv6ChainTableIndex | 1.3.6.1.4.1.74.1.30.9.7.1.2 | Integer32 | read-only | Shows what table this chain belongs to. Corresponds to ngfwIPv6TableIndex in ngIPv6FirewallTable. |
| STR ngfwIPv6ChainName | 1.3.6.1.4.1.74.1.30.9.7.1.3 | DisplayString | read-only | The name of this chain. |
| I32 ngfwIPv6ChainsNumberOfRules | 1.3.6.1.4.1.74.1.30.9.7.1.4 | Integer32 | read-only | The number of rules in this particular chain. |
| ngIPv6FirewallRuleTable | 1.3.6.1.4.1.74.1.30.9.8 | not-accessible | The (conceptual) table of IPv6 firewall rules on the device. An entry shall be placed in the storage rule for each rule. | |
| ngIPv6FirewallRuleEntry | 1.3.6.1.4.1.74.1.30.9.8.1 | not-accessible | A (conceptual) entry for one logical IPv6 firewall rule area on the host. | |
| I32 ngfwIPv6RuleIndex | 1.3.6.1.4.1.74.1.30.9.8.1.1 | Integer32 | not-accessible | A unique value for each logical IPv6 firewall rule contained by the device. |
| I32 ngfwIPv6RuleTableIndex | 1.3.6.1.4.1.74.1.30.9.8.1.2 | Integer32 | read-only | Shows what table this rule belongs to. Corresponds to ngfwIPv6TableIndex in ngIPv6FirewallTable. |
| I32 ngfwIPv6RuleChainIndex | 1.3.6.1.4.1.74.1.30.9.8.1.3 | Integer32 | read-only | Shows what chain this rule belongs to. Corresponds to ngfwIPv6ChainIndex in ngIPv6FirewallChainTable. |
| U32 ngfwIPv6RulePackets | 1.3.6.1.4.1.74.1.30.9.8.1.4 | Unsigned32 | read-only | Total packets for this rule. |
| U32 ngfwIPv6RuleBytes | 1.3.6.1.4.1.74.1.30.9.8.1.5 | Unsigned32 | read-only | Total bytes for this rule. |
| STR ngfwIPv6RuleTarget | 1.3.6.1.4.1.74.1.30.9.8.1.6 | DisplayString | read-only | The rule target. |
| STR ngfwIPv6RuleProtocol | 1.3.6.1.4.1.74.1.30.9.8.1.7 | DisplayString | read-only | The rule protocol. |
| STR ngfwIPv6RuleInIface | 1.3.6.1.4.1.74.1.30.9.8.1.8 | DisplayString | read-only | The rule input interface. |
| STR ngfwIPv6RuleOutIface | 1.3.6.1.4.1.74.1.30.9.8.1.9 | DisplayString | read-only | The rule output interface. |
| ADR ngfwIPv6RuleSrcIp | 1.3.6.1.4.1.74.1.30.9.8.1.10 | InetAddressIPv6 | accessible-for-notify | The rule source IP. Not used and set to all zeroes for IPv4 firewall output. |
| I32 ngfwIPv6RuleSrcMask | 1.3.6.1.4.1.74.1.30.9.8.1.11 | Integer32 | read-only | The rule source mask in CIDR-compliant format. Not used and set to all zeroes for IPv4 firewall output. |
| ADR ngfwIPv6RuleDstIp | 1.3.6.1.4.1.74.1.30.9.8.1.12 | InetAddressIPv6 | accessible-for-notify | The rule source IP. Not used and set to all zeroes for IPv4 firewall output. |
| I32 ngfwIPv6RuleDstMask | 1.3.6.1.4.1.74.1.30.9.8.1.13 | Integer32 | read-only | The rule source mask in CIDR-compliant format. Not used and set to all zeroes for IPv4 firewall output. |
| STR ngfwIPv6RuleMisc | 1.3.6.1.4.1.74.1.30.9.8.1.14 | DisplayString | read-only | The rule MISC section. |
| ngRogueMacInfo | 1.3.6.1.4.1.74.1.30.10 | |||
| INT ngRogueMacStatus | 1.3.6.1.4.1.74.1.30.10.1 | INTEGER | read-only | Inidicates whether or not Rogue MAC detection has been enabled in Service Manager. |
| ngRogueMacTable | 1.3.6.1.4.1.74.1.30.10.2 | not-accessible | The (conceptual) table of rogue MACs detected by the device. An entry shall be placed in the storage table for each rogue MAC. | |
| ngRogueMacEntry | 1.3.6.1.4.1.74.1.30.10.2.1 | not-accessible | A (conceptual) entry for one logical rogue MAC area on the host. | |
| I32 ngrmIndex | 1.3.6.1.4.1.74.1.30.10.2.1.1 | Integer32 | not-accessible | A unique value for each logical rogue MAC detected by the device. |
| STR ngrmMac | 1.3.6.1.4.1.74.1.30.10.2.1.2 | DisplayString | read-only | The MAC address of this detected rogue MAC. One entry that is zeroed out is returned when there are no rogue MACs detected. |
| STR ngrmTimestamp | 1.3.6.1.4.1.74.1.30.10.2.1.3 | DisplayString | read-only | The date and time of when this rogue MAC was detected. Returned as a regular string in the format MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when there are no rogue MACs detected. The time returned is the local time on the AT&T VPN Gateway. To determine how the AT&T VPN Gateway's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngrmTimestampDAT. |
| STR ngrmIface | 1.3.6.1.4.1.74.1.30.10.2.1.4 | DisplayString | read-only | The interface this rogue MAC was detected on. One entry that with a value of 'NONE' and a msg is returned when there are no rogue MACs detected. |
| DAT ngrmTimestampDAT | 1.3.6.1.4.1.74.1.30.10.2.1.5 | DateAndTime | read-only | The date and time of when this rogue MAC was detected. Returns January 1 year 0 time 0 when there are no rogue MACs detected or the time is unknown. NOTE: This entry replaces ngrmTimestamp. |
| ngDialInfo | 1.3.6.1.4.1.74.1.30.11 | |||
| STR ngdiPhoneNum | 1.3.6.1.4.1.74.1.30.11.1 | DisplayString | read-only | The full phone number that will be dialed by the AT&T VPN Gateway. This also includes dial prefix information. For example, the AT&T VPN Gateway might have to dial the number nine and then a comma to access an outside line. The nine and the comma will be included in this entry. |
| INT ngdiLastTestResult | 1.3.6.1.4.1.74.1.30.11.2 | INTEGER | read-only | The result of the last dial test. If no dial test has been performed yet then 'failure' is returned. If a dial test is not needed because dial is currently up then 'success' is returned. |
| STR ngdiLastTestCompleteTime | 1.3.6.1.4.1.74.1.30.11.3 | DisplayString | read-only | The approximate time the last dial test completed given in the format MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when no test is scheduled. or when no test has run yet. If the dial connection is currently in use then the dial test is not needed (since dial is obviously already working). ngdiLastTestCompleteTime is simply updated to the recent time whent the AT&T VPN Gateway last verified that the dial connection was still up. The time returned is the local time on the AT&T VPN Gateway. To determine how the AT&T VPN Gateway's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngdiLastTestCompleteTimeDAT. |
| INT ngdiDialTestFailCategory | 1.3.6.1.4.1.74.1.30.11.4 | INTEGER | accessible-for-notify | Shows what type of category the dial test failure would be put in. For example, a busy signal would return dialProblemWarning but a bad password would return dialProblemError. If a dial test is not needed because dial is currently up then dialProblemMessage is returned. |
| STR ngdiDialTestFailReason | 1.3.6.1.4.1.74.1.30.11.5 | DisplayString | accessible-for-notify | String that shows why the dial test failed. If the test was successful or the dial connection is currently up then 'success' is returned. |
| DAT ngdiLastTestCompleteTimeDAT | 1.3.6.1.4.1.74.1.30.11.6 | DateAndTime | read-only | If the dial connection is currently in use then the dial test is not needed (since dial is obviously already working). ngdiLastTestCompleteTimeDAT is simply updated to the recent time whent the AT&T VPN Gateway last verified that the dial connection was still up. Returns January 1 year 0 time 0 when no test is scheduled or when no test has run yet. The time returned is the local time on the AT&T VPN Gateway. To determine how the AT&T VPN Gateway's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry replaces ngdiLastTestCompleteTime. |
| STR ngdiSecondaryPhoneNum | 1.3.6.1.4.1.74.1.30.11.7 | DisplayString | read-only | Specifies the secondary phone number to be tried for Dial Backup in case the primary Dial Backup phone number is not available. |
| ngDhcpLeaseInfo | 1.3.6.1.4.1.74.1.30.12 | |||
| ngDhcpLeaseTable | 1.3.6.1.4.1.74.1.30.12.1 | not-accessible | The (conceptual) table of all current, active DHCP leases on the device. An entry shall be placed in the storage table for each DHCP lease. | |
| ngDhcpLeaseEntry | 1.3.6.1.4.1.74.1.30.12.1.1 | not-accessible | A (conceptual) entry for one logical DHCP lease on the host. | |
| I32 ngdhlIndex | 1.3.6.1.4.1.74.1.30.12.1.1.1 | Integer32 | not-accessible | A unique value for each logical DHCP lease contained by the device. |
| IP ngdhlLeaseAddr | 1.3.6.1.4.1.74.1.30.12.1.1.2 | IpAddress | read-only | The IP address associated with an indivdual DHCP lease. |
| STR ngdhlMac | 1.3.6.1.4.1.74.1.30.12.1.1.3 | DisplayString | read-only | The MAC address associated with an indivdual DHCP lease. |
| STR ngdhlHostname | 1.3.6.1.4.1.74.1.30.12.1.1.4 | DisplayString | read-only | The hostname associated with an indivdual DHCP lease. |
| I32 ngdhlPort | 1.3.6.1.4.1.74.1.30.12.1.1.5 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngdhlVlanId | 1.3.6.1.4.1.74.1.30.12.1.1.6 | Integer32 | read-only | The VLAN ID on the device associated with an indivdual DHCP lease. |
| ngCaptPortalInfo | 1.3.6.1.4.1.74.1.30.13 | |||
| ngCapPorTable | 1.3.6.1.4.1.74.1.30.13.1 | not-accessible | The (conceptual) table of all current, active DHCP leases on the device. An entry shall be placed in the storage table for each DHCP lease. | |
| ngCapPorEntry | 1.3.6.1.4.1.74.1.30.13.1.1 | not-accessible | A (conceptual) entry for one logical DHCP lease on the host. | |
| I32 ngcpIndex | 1.3.6.1.4.1.74.1.30.13.1.1.1 | Integer32 | not-accessible | A unique value for each logical DHCP lease contained by the device. |
| IP ngcpAddr | 1.3.6.1.4.1.74.1.30.13.1.1.2 | IpAddress | read-only | The IP address associated with an indivdual DHCP lease. |
| STR ngcpMac | 1.3.6.1.4.1.74.1.30.13.1.1.3 | DisplayString | read-only | The MAC address associated with an indivdual DHCP lease. |
| STR ngcpUser | 1.3.6.1.4.1.74.1.30.13.1.1.4 | DisplayString | read-only | The hostname associated with an indivdual DHCP lease. |
| I32 ngcpDuration | 1.3.6.1.4.1.74.1.30.13.1.1.5 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpMaxDuration | 1.3.6.1.4.1.74.1.30.13.1.1.6 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpState | 1.3.6.1.4.1.74.1.30.13.1.1.7 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpIdle | 1.3.6.1.4.1.74.1.30.13.1.1.8 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpMaxIdle | 1.3.6.1.4.1.74.1.30.13.1.1.9 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpPort | 1.3.6.1.4.1.74.1.30.13.1.1.10 | Integer32 | read-only | The physical port (if valid) on the device associated with an indivdual DHCP lease. |
| I32 ngcpVlanId | 1.3.6.1.4.1.74.1.30.13.1.1.11 | Integer32 | read-only | The VLAN ID on the device associated with an indivdual DHCP lease. |
| attInbTunInfo | 1.3.6.1.4.1.74.1.30.14 | |||
| attInbTunTable | 1.3.6.1.4.1.74.1.30.14.1 | not-accessible | The (conceptual) table of inbound tunnels on the device. An entry shall be placed in the storage table for each inbound tunnel. | |
| attInbTunEntry | 1.3.6.1.4.1.74.1.30.14.1.1 | not-accessible | A (conceptual) entry for one logical inbound tunnel area on the host. | |
| I32 inbTunIndex | 1.3.6.1.4.1.74.1.30.14.1.1.1 | Integer32 | not-accessible | A unique value for each logical inbound tunnel contained by the device. |
| STR inbTunClientTransAddr | 1.3.6.1.4.1.74.1.30.14.1.1.2 | DisplayString | read-only | The client transport address of this inbound tunnel. |
| STR inbTunLocalIpsecIface | 1.3.6.1.4.1.74.1.30.14.1.1.3 | DisplayString | read-only | The IPsec interface associated with this inbound tunnel. |
| STR inbTunType | 1.3.6.1.4.1.74.1.30.14.1.1.4 | DisplayString | read-only | The tunnel type of this inbound tunnel. |
| STR inbTunUserid | 1.3.6.1.4.1.74.1.30.14.1.1.5 | DisplayString | read-only | The userid associated with this inbound tunnel. |
| STR inbTunSrvConfigProf | 1.3.6.1.4.1.74.1.30.14.1.1.6 | DisplayString | read-only | The Service Manager profile associated with this inbound tunnel. |
| DAT inbTunTimeEstablished | 1.3.6.1.4.1.74.1.30.14.1.1.7 | DateAndTime | read-only | Time this inbound tunnel was established. |
| TIK inbTunDuration | 1.3.6.1.4.1.74.1.30.14.1.1.8 | TimeTicks | read-only | How long this inbound tunnel has been up. |
| TIK inbTunIdleTimeout | 1.3.6.1.4.1.74.1.30.14.1.1.9 | TimeTicks | read-only | This inbound tunnel's idle timeout setting. |
| TIK inbTunCurrIdleTimeout | 1.3.6.1.4.1.74.1.30.14.1.1.10 | TimeTicks | read-only | How long this inbound tunnel has been idle. |
| TIK inbTunNegIkePhase1Lifet | 1.3.6.1.4.1.74.1.30.14.1.1.11 | TimeTicks | read-only | This inbound tunnel's negotiated IKE Phase 1 lifetime. |
| INT inbTunNatTNegotiated | 1.3.6.1.4.1.74.1.30.14.1.1.12 | INTEGER | read-only | Is NAT-T negotiated for this inbound tunnel? |
| I32 inbTunActClientSaNeg | 1.3.6.1.4.1.74.1.30.14.1.1.13 | Integer32 | read-only | Active client SA's negotiated for this inbound tunnel. |
| attInbTunNetTable | 1.3.6.1.4.1.74.1.30.14.2 | not-accessible | The (conceptual) table of inbound tunnel networks on the device. An entry shall be placed in the storage table for each inbound tunnel network. | |
| attInbTunNetEntry | 1.3.6.1.4.1.74.1.30.14.2.1 | not-accessible | A (conceptual) entry for one logical inbound tunnel network area on the host. | |
| I32 inbTunNetIndex | 1.3.6.1.4.1.74.1.30.14.2.1.1 | Integer32 | not-accessible | A unique value for each logical inbound tunnel's network contained by the device. |
| STR inbTunNetNetwork | 1.3.6.1.4.1.74.1.30.14.2.1.2 | DisplayString | read-only | This inbound tunnel network. |
| DAT inbTunNetTimeEstablished | 1.3.6.1.4.1.74.1.30.14.2.1.3 | DateAndTime | read-only | Time this inbound tunnel network was established. |
| TIK inbTunNetNegIkePhase2Lifet | 1.3.6.1.4.1.74.1.30.14.2.1.4 | TimeTicks | read-only | This inbound tunnel network's negotiated IKE Phase 2 lifetime. |
| STR inbTunNetEspAlgorithm | 1.3.6.1.4.1.74.1.30.14.2.1.5 | DisplayString | read-only | This inbound tunnel network's ESP algorithm. |
| INT inbTunNetCompression | 1.3.6.1.4.1.74.1.30.14.2.1.6 | INTEGER | read-only | Is compression negotiated for this inbound tunnel? |
| STR inbTunNetClientTransAddr | 1.3.6.1.4.1.74.1.30.14.2.1.7 | DisplayString | read-only | Shows what inbound tunnel this network belongs to. Corresponds to inbTunClientTransAddr in attInbTunEntry. |
RFC description
Provides management for AT&T VPN Gateway devices including tunnel configuration, circuit speed, and data usage statistics. Includes VRRP state tracking and 3G cell network reporting.
Start monitoring AT&T managed VPN Gateway (branch/SMB CPE) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.