ATMEL-MIB

All MIBs › ATMEL-MIB

Description: MIB for system control, wireless configuration, and trap management on Atmel-based wireless networking devices

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ATMEL-MIB?

ATMEL-MIB is an Atmel private enterprise MIB for managing wireless networking devices (access points) built on Atmel's wireless chipset/reference platform, covering system control, wireless configuration, and site-survey/trap functions. It exposes system-level control objects — sysReset, sysLoadDefaults, sysUpload, sysTrapSwitch — alongside device identity/status (sysDescr, sysDeviceInfo, sysDeviceMoreInfo) and IP/network configuration (operIPAddress, operIPMask, operEthernetAddress, operGateway) plus a SiteSurveyCommand for wireless scanning. In terms of hardware/software status, this MIB is used to check basic device identity/description and to remotely trigger management actions like a reset, restore-to-defaults, or firmware/config upload — administrative control functions rather than deep sensor telemetry, though sysDeviceInfo/sysDeviceMoreInfo carry device state details. It appears to be a self-contained vendor MIB layered over the standard SNMP internet/mgmt tree with no notable external MIB dependency beyond that. It is deployed on Atmel-chipset-based wireless access points/bridges, often used by smaller or white-label WLAN hardware vendors. Network engineers evaluating or troubleshooting this functionality can download the ATMEL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ATMEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Atmel-chipset-based wireless access points/bridges

Monitoring Examples

An admin would poll sysDescr and sysDeviceInfo/sysDeviceMoreInfo to identify a fielded Atmel-based access point's model and firmware state, and could set sysTrapSwitch to enable/disable trap notifications from the unit. Issuing a SiteSurveyCommand would trigger the AP to scan for nearby wireless networks/interference, useful for diagnosing RF issues, while sysReset or sysLoadDefaults would be used to remotely recover a misbehaving unit. operIPAddress/operGateway confirm the unit's current network reachability configuration.

What Can Be Monitored

device description/identity
device status detail
IP address/gateway/subnet configuration
site survey / RF scan results
trap notification enable state

Imported Objects

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
internet	1.3.6.1
directory	1.3.6.1.1
mgmt	1.3.6.1.2
experimental	1.3.6.1.3
private	1.3.6.1.4
enterprises	1.3.6.1.4.1
atmel	1.3.6.1.4.1.12350
NTF trapReassociation	1.3.6.1.4.1.12350.0.1			This trap message is sent when a STAtion's reassosiation request is received.
NTF trapRoamOut	1.3.6.1.4.1.12350.0.2			This trap message is used to indicate that a STAtion has roamed out of the Wireless bridge's coverage area.
NTF trapAssociation	1.3.6.1.4.1.12350.0.3			Indicates the reception of an association request packet and the sender STAtion's successful association with the Access Point.
NTF trapDisassociation	1.3.6.1.4.1.12350.0.4			This trap message is sent when a disassociation notification packet is received from a STAtion.
NTF trapAssociationExpire	1.3.6.1.4.1.12350.0.5			This trap message is sent when the association's maximum time interval expires for an associated STAtion.
NTF trapReset	1.3.6.1.4.1.12350.0.6			This trap message is sent when Access Point Resets.
NTF trapSettingPingIPAddress	1.3.6.1.4.1.12350.0.7			This trap message is sent when the Access Point IP address is set with the transmition of a ping message.
NTF trapStartUp	1.3.6.1.4.1.12350.0.8			This trap message is sent when Access Point Starts Up.
NTF trapFailedToEraseFlash	1.3.6.1.4.1.12350.0.9			This trap message is sent when Access Point Failed To Erase Flash.
NTF trapAPClientScanning	1.3.6.1.4.1.12350.0.10			Access Point Client is scanning...
NTF trapAPClientAuthenticating	1.3.6.1.4.1.12350.0.11			Access Point Client is authenticating with the AP.
NTF trapAPClientAssociating	1.3.6.1.4.1.12350.0.12			Access Point Client is associating with the AP.
NTF trapAPClientReAssociating	1.3.6.1.4.1.12350.0.13			Access Point Client is reassociating with the AP.
NTF trapAPClientAuthenticationFailed	1.3.6.1.4.1.12350.0.14			Access Point Client has failed authenticating with the AP.
NTF trapAPClientAssociationFailed	1.3.6.1.4.1.12350.0.15			Access Point Client has failed associating with the AP.
NTF trapAPClientConnected	1.3.6.1.4.1.12350.0.16			Access Point Client has been connected with the AP.
NTF trapAPClientDisconnected	1.3.6.1.4.1.12350.0.17			Access Point Client has been disconnected from the AP.
NTF trapAPClientScanFailed	1.3.6.1.4.1.12350.0.18			Access Point Client has failed scanning!
NTF trapAPClientJoinFailed	1.3.6.1.4.1.12350.0.19			Access Point Client has failed joining!
NTF trapAPClientJoining	1.3.6.1.4.1.12350.0.20			Access Point Client is in join state.
atmelmib	1.3.6.1.4.1.12350.1
atmelSys	1.3.6.1.4.1.12350.1.1
sysCtrlGRP	1.3.6.1.4.1.12350.1.1.1
STR sysDescr	1.3.6.1.4.1.12350.1.1.1.1	DisplayString	read-only	A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
INT sysReset	1.3.6.1.4.1.12350.1.1.1.2	INTEGER	read-write	By setting this attribute enable(1), a reset command to the system is issued.
INT sysTrapSwitch	1.3.6.1.4.1.12350.1.1.1.3	INTEGER	read-write	This attribute enables the transmission of SNMP.V1 TRAPs.
INT sysLoadDefaults	1.3.6.1.4.1.12350.1.1.1.4	INTEGER	read-write	Setting this attribute to enable(1), will cause the system to load the factory default values of all the operational parameters.
OCT sysDeviceInfo	1.3.6.1.4.1.12350.1.1.1.5	OCTET STRING	read-write	First 92 bytes of Hardware device configuration struct. HARD_CONFIGURATION_STUCT{ unsigned long StructVersion; unsigned char MacAddress[6]; unsigned char Channel; unsigned char RegulatoryDomain; unsigned long ProductType; unsigned char OEMname[32]; unsigned long OEMID; unsigned char ProductName[32]; unsigned long HardwareRevision; unsigned char PID_VID[4]; //Product ID/ Vendor ID unsigned int sysOIDSize; unsigned short sysOID[16]; unsigned char CountryCode[3]; unsigned char Reserved1; unsigned short ChannelInformation; unsigned char Reserved2[2]; char TxPower[14]; unsigned char Reserved3[10]; }
INT sysUpload	1.3.6.1.4.1.12350.1.1.1.6	INTEGER	read-write	By setting this attribute enable(1), a Upload configuration command to the system is issued.
INT siteSurveyCommand	1.3.6.1.4.1.12350.1.1.1.7	INTEGER	read-write	By setting this attribute enable(1), a Site Survey command to the system is issued.
OCT sysDeviceMoreInfo	1.3.6.1.4.1.12350.1.1.1.8	OCTET STRING	read-write	Last 32 bytes of Hardware device configuration struct. HARD_CONFIGURATION_STUCT{ unsigned long StructVersion; unsigned char MacAddress[6]; unsigned char Channel; unsigned char RegulatoryDomain; unsigned long ProductType; unsigned char OEMname[32]; unsigned long OEMID; unsigned char ProductName[32]; unsigned long HardwareRevision; unsigned char PID_VID[4]; //Product ID/ Vendor ID unsigned int sysOIDSize; unsigned short sysOID[16]; unsigned char CountryCode[3]; unsigned char Reserved1; unsigned short ChannelInformation; unsigned char Reserved2[2]; char TxPower[14]; unsigned char Reserved3[10]; }
operBridgingLevel	1.3.6.1.4.1.12350.1.1.2
IP operIPAddress	1.3.6.1.4.1.12350.1.1.2.1	IpAddress	read-write	The IP address of this device used over its Ethernet or Wireless LAN port.
IP operIPMask	1.3.6.1.4.1.12350.1.1.2.2	IpAddress	read-write	The IP Network mask used by the IP entity when accessing devices through any of its LAN Ports (Ethernet or WLAN).
OCT operEthernetAddress	1.3.6.1.4.1.12350.1.1.2.3	OCTET STRING	read-only	The MAC Address of the Ethernet interface.
IP operGateway	1.3.6.1.4.1.12350.1.1.2.4	IpAddress	read-write	Gateway default IP address.
INT operDHCP	1.3.6.1.4.1.12350.1.1.2.5	INTEGER	read-write	When setting this attribute to enable(1), the system will enable DHCP protocol.
INT operPrimaryPort	1.3.6.1.4.1.12350.1.1.2.6	INTEGER	read-write	This attribute indicates the primaty port.Ethernet or Wireless.
INT operConfigurationPort	1.3.6.1.4.1.12350.1.1.2.7	INTEGER	read-write	This attribute indicates the Configuration port.Ethernet or Wireless or Both of them.
INT operTrapPort	1.3.6.1.4.1.12350.1.1.2.8	INTEGER	read-write	This attribute indicates the Trap port.
operFiltering	1.3.6.1.4.1.12350.1.1.3
INT operIPFilter	1.3.6.1.4.1.12350.1.1.3.1	INTEGER	read-write	When setting this attribute to enable(1), the system will filter out all non IP-traffic.
INT operForwarbBcast	1.3.6.1.4.1.12350.1.1.3.2	INTEGER	read-write	When setting this attribute to disable(2), the system will not forward broadcast traffic to the Wireless Port.
INT operSendBackBcast	1.3.6.1.4.1.12350.1.1.3.3	INTEGER	read-write	When setting this attribute to disable(2), the system will not send back broadcast traffic to the Wireless Port.
INT operSendBackUnicast	1.3.6.1.4.1.12350.1.1.3.4	INTEGER	read-write	When setting this attribute to disable(2), the system will not send back unicast traffic to the Wireless Port.
operBridgeOperationalMode	1.3.6.1.4.1.12350.1.1.4
INT bridgeOperationalMode	1.3.6.1.4.1.12350.1.1.4.1	INTEGER	read-write	The Operational Mode of Bridge. Access Point, Access Point client, Wireless Bridge Point to Point, Wireless Bridge Point to MultiPoint.
OCT bridgeRemoteBridgeBSSID	1.3.6.1.4.1.12350.1.1.4.2	OCTET STRING	read-write	The Preferred BSSID if the device is at Access Point client mode or the remote Mac if the device is at Wireless Bridge Point to Point mode.
dot1dStatic	1.3.6.1.4.1.12350.1.1.5
INT staticMacFilterNum	1.3.6.1.4.1.12350.1.1.5.1	INTEGER	read-write	This parameter's value indicates the number of the currently static MAC filters.
dot1dStaticTable	1.3.6.1.4.1.12350.1.1.5.2		not-accessible	A table containing filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.
dot1dStaticEntry	1.3.6.1.4.1.12350.1.1.5.2.1		not-accessible	Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.
OCT dot1dStaticAddress	1.3.6.1.4.1.12350.1.1.5.2.1.1	OCTET STRING	read-write	The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.
protocolFilterGRP	1.3.6.1.4.1.12350.1.1.6
INT protocolFilterNum	1.3.6.1.4.1.12350.1.1.6.1	INTEGER	read-write	This parameter's value indicates the number of the currently protocol filters.
protocolFilterTable	1.3.6.1.4.1.12350.1.1.6.2		not-accessible	A table containing filtering information configured into the bridge by (local or network) management specifying the set of protocol filter.
protocolFilterEntry	1.3.6.1.4.1.12350.1.1.6.2.1		not-accessible	Filtering information configured into the bridge by (local or network) management specifying the set of protocol filter.
OCT protocolFilterCode	1.3.6.1.4.1.12350.1.1.6.2.1.1	OCTET STRING	read-write	The protocol code configured into the bridge by (local or network) management specifying the set of protocol filter.
STR protocolFilterDescription	1.3.6.1.4.1.12350.1.1.6.2.1.2	DisplayString	read-write	A textual description of the protocol.
INT protocolFilterActivity	1.3.6.1.4.1.12350.1.1.6.2.1.3	INTEGER	read-write	This object indicates the status of this filter.
ethStatisticsGRP	1.3.6.1.4.1.12350.1.1.7
OCT ethRxStatistics	1.3.6.1.4.1.12350.1.1.7.1	OCTET STRING	read-only	Ethernet Rx Statistics EthernetRxStatistics{ unsigned long TotalBytesRx; unsigned long TotalPacketsRx; unsigned long PacketCRCErrorRx; unsigned long MulticastPacketRx; unsigned long BroadcastPacketRx; unsigned long ControlFramesRx; unsigned long PauseFramesRx; unsigned long UnknownOPCodeRx; unsigned long AlignmentRxError; unsigned long LengthOutOfRangeRx; unsigned long CodeErrorRx; unsigned long FalseCarrierRx; unsigned long UndersizePacketsRx; unsigned long OversizePacketsRx; unsigned long TotalFragmentsRx; unsigned long TotalJabberRx; }
OCT ethTxStatistics	1.3.6.1.4.1.12350.1.1.7.2	OCTET STRING	read-only	Ethernet Tx Statistics EthernetTxStatistics{ unsigned long TotalBytesTx; unsigned long TotalPacketsTx; unsigned long PacketCRCErrorTx; unsigned long MulticastPacketTx; unsigned long BroadcastPacketTx; unsigned long UnicastPacketTx; unsigned long PauseFramesTx; unsigned long SingleDeferPacketTx; unsigned long MultiDeferPacketsTx; unsigned long SingleCollisionsTx; unsigned long MultiCollisionsTx; unsigned long LateCollisionsTx; unsigned long ExcessiveCollisionTx; unsigned long TotalCollisionsTx; }
testModeSettingsGRP	1.3.6.1.4.1.12350.1.1.8
INT testModeOnOff	1.3.6.1.4.1.12350.1.1.8.1	INTEGER	read-write	When setting this attribute to enable(1), the device be at test mode.
OCT testModeCommandStruct	1.3.6.1.4.1.12350.1.1.8.2	OCTET STRING	read-write	typedef struct __CONT_PKT_TX { UINT8 Channel; UINT8 Antenna; UINT8 TxPower; UINT8 TxRate; UINT8 TxFilter; UINT8 Reserved; UINT16 IFrameTime; UINT32 FrameLength; UINT32 FramesToTransmit; UINT8 Pattern; UINT8 Reserved1[3]; }CONT_PKT_TX;
OCT testModeRadioConfiguration	1.3.6.1.4.1.12350.1.1.8.8	OCTET STRING	read-write	Configuration of radio derived from tests. CR17 Reg 1-14, CR20 Reg 1-14, CR21 Reg 1-14, CR1, CR2, CR3, CR28, CR29
OCT testModeStatistics	1.3.6.1.4.1.12350.1.1.8.9	OCTET STRING	read-only	Statistics derive from tests testModeStatistics{ unsigned long SuccessFrames; unsigned long FailedFrames; unsigned long PacketsTx; }
authorizedSettingsGRP	1.3.6.1.4.1.12350.1.1.9
OCT authorizedUserPass	1.3.6.1.4.1.12350.1.1.9.1	OCTET STRING	read-write	The community name of User.
OCT authorizedAdminPass	1.3.6.1.4.1.12350.1.1.9.2	OCTET STRING	read-write	The community name of Administrator.
OCT authorizedManufactPass	1.3.6.1.4.1.12350.1.1.9.3	OCTET STRING	read-write	The community name of Manufacturer.
wireless	1.3.6.1.4.1.12350.1.2
operationalSettingsGRP	1.3.6.1.4.1.12350.1.2.1
INT operChannelID	1.3.6.1.4.1.12350.1.2.1.1	INTEGER	read-write	The operating frequency channel. Valid numbers are as defind in ISO/IEC 8802-11:1999, 15.4.6.2.
INT operESSIDLength	1.3.6.1.4.1.12350.1.2.1.2	INTEGER	read-write	The ESSID Length
OCT operESSID	1.3.6.1.4.1.12350.1.2.1.3	OCTET STRING	read-write	The network name. The size of the network name should not be more than 32 characters long.
INT operRTSThreshold	1.3.6.1.4.1.12350.1.2.1.4	INTEGER	read-write	This attribute indicates the number of bytes in an MPDU (frame), above which an RTS/CTS handshake will be performed. Setting this attribute to be larger than the maximum frame size, will prevent the RTS/CTS handshake for frames trassmitted by this station.
INT operFragmentationThreshold	1.3.6.1.4.1.12350.1.2.1.5	INTEGER	read-write	This attribute indicates the number of bytes in an MPDU (frame), above which MPDU fragmentation will be performed.
INT operPreambleType	1.3.6.1.4.1.12350.1.2.1.6	INTEGER	read-write	This parameter's value indicates the Preamble Type of device. Short or Long.
INT operAuthenticationType	1.3.6.1.4.1.12350.1.2.1.7	INTEGER	read-write	This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one of the following: 1 - Open System, 2 - Shared Key 3 - Both Type
OCT operBasicRates	1.3.6.1.4.1.12350.1.2.1.8	OCTET STRING	read-write	This attribute indicates the basic and supported rates of Access Point.Valid format is as defind in ISO/IEC 8802-11:1999
INT operAutoRateFallBack	1.3.6.1.4.1.12350.1.2.1.9	INTEGER	read-write	This attribute indicates if Auto Rate Fall Back is enable or disable.
OCT operAccessPointName	1.3.6.1.4.1.12350.1.2.1.10	OCTET STRING	read-write	The AP name.
INT operSSIDBroadcasting	1.3.6.1.4.1.12350.1.2.1.11	INTEGER	read-write	This attribute indicates if SSID is broadcasting or not.
INT operAntennaSettings	1.3.6.1.4.1.12350.1.2.1.12	INTEGER	read-write	.
INT operInterRoaming	1.3.6.1.4.1.12350.1.2.1.13	INTEGER	read-write	.
INT operBeaconPeriod	1.3.6.1.4.1.12350.1.2.1.14	INTEGER	read-write	.
INT operDTIM	1.3.6.1.4.1.12350.1.2.1.15	INTEGER	read-write	.
privacyGRP	1.3.6.1.4.1.12350.1.2.2
OCT defaultWEPKey1	1.3.6.1.4.1.12350.1.2.2.1	OCTET STRING	write-only	A WEP default secret key value.
OCT defaultWEPKey2	1.3.6.1.4.1.12350.1.2.2.2	OCTET STRING	write-only	A WEP default secret key value.
OCT defaultWEPKey3	1.3.6.1.4.1.12350.1.2.2.3	OCTET STRING	write-only	A WEP default secret key value.
OCT defaultWEPKey4	1.3.6.1.4.1.12350.1.2.2.4	OCTET STRING	write-only	A WEP default secret key value.
INT privacyWEPEnable	1.3.6.1.4.1.12350.1.2.2.5	INTEGER	read-write	This attribute, when enable64(1) or enable128(3), indicates that the 802.11 standard encryption mechanism (WEP) is implemented. WEP64, WEP128 or disable
INT privacyDefaultWEPKeyID	1.3.6.1.4.1.12350.1.2.2.6	INTEGER	read-write	This attribute shall indicate the use of the first, second, third or fourth DefaultWEPKey when set to values of one, two, three or four.
wLstatisticsGRP	1.3.6.1.4.1.12350.1.2.3
OCT wirelessStatistics	1.3.6.1.4.1.12350.1.2.3.1	OCTET STRING	read-only	Wireless Statistics. 22 elements(ULONG) WirelessStatistics{ unsigned long UnicastTransmittedPackets; unsigned long BroadcastTransmittedPacets; unsigned long MulticastTransmittedPackets; unsigned long TransmittedBeacon; unsigned long TransmittedACK; unsigned long TransmittedRTS; unsigned long TransmittedCTS; unsigned long UnicastReceivedPackets; unsigned long BroadcastReceivedPackets; unsigned long MulticastReceivedPackets; unsigned long ReceivedBeacon; unsigned long ReceivedACK; unsigned long ReceivedRTS; unsigned long ReceivedCTS; unsigned long ACKFailure; unsigned long CTSFailure; unsigned long RetryPackets; unsigned long ReceivedDuplicate; unsigned long FailedPackets; unsigned long AgedPackets; unsigned long FCSError; unsigned long InvalidPLCP; }
wLSiteSurveyGRP	1.3.6.1.4.1.12350.1.2.4
OCT channelStatus	1.3.6.1.4.1.12350.1.2.4.1	OCTET STRING	read-only	.
associatedStationsGRP	1.3.6.1.4.1.12350.1.2.5
INT associatedSTAsNum	1.3.6.1.4.1.12350.1.2.5.1	INTEGER	read-only	This parameter's value indicates the number of the currently associated STAtions. Associated STAtions should not be more than 2007.
OCT associatedSTAsInfo	1.3.6.1.4.1.12350.1.2.5.2	OCTET STRING	read-only	The associated STAtion's Information. associatedSTAsInfo{ unsigned sort Num; unsigned char MacAddress[6]; }
authorizedMacAddressesGRP	1.3.6.1.4.1.12350.1.2.6
INT authorizationMacEnable	1.3.6.1.4.1.12350.1.2.6.1	INTEGER	read-write	When setting this attribute to 1, the Authorization Mac Address Table will be enabled in allow mode. When setting this attribute to 3, the Authorization Mac Address Table will be enabled in deny mode.
OCT authorizedMac	1.3.6.1.4.1.12350.1.2.6.2	OCTET STRING	read-write	The Authorized Wireless Mac Addresses AuthorizedMacTableString{ unsigned sort Action; //Set 0x01 or Get 0x02 unsigned sort NumOfAllTableAddresses; unsigned sort NumOfCurrentAddress; unsigned char MacAddress[6]; }
wLKnownAPGRP	1.3.6.1.4.1.12350.1.2.7
OCT wirelessKnownAPs	1.3.6.1.4.1.12350.1.2.7.1	OCTET STRING	read-only	.
INT selectedBSSListNumber	1.3.6.1.4.1.12350.1.2.7.2	INTEGER	write-only	.
advancedPrivacyGRP	1.3.6.1.4.1.12350.1.2.8
INT dot1xEnable	1.3.6.1.4.1.12350.1.2.8.1	INTEGER	read-write	.
INT broadcastKeyPeriod	1.3.6.1.4.1.12350.1.2.8.2	INTEGER	read-write	.
IP serverIP	1.3.6.1.4.1.12350.1.2.8.3	IpAddress	read-write	.
OCT serverSecret	1.3.6.1.4.1.12350.1.2.8.4	OCTET STRING	write-only	.
traps	1.3.6.1.4.1.12350.1.3
OCT trapSTAMacAddress	1.3.6.1.4.1.12350.1.3.1	OCTET STRING	read-only	The MAC address of a station device

RFC description

Atmel vendor-private MIB defining the enterprise OID root namespace for Atmel Corporation (vendor-specific SMI root).

Start monitoring Atmel-chipset wireless access points/bridges (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ATMEL-MIB

What Is ATMEL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description