| OID symbolic | OID numeric | Type | Access | Description |
|---|
| askeyHwInfo | 1.3.6.1.4.1.3646.1300.2.15 | | | This Mib describs with the information of
network card, line card and fan module. |
| askeyHwInfoTable | 1.3.6.1.4.1.3646.1300.2.15.1 | | not-accessible | This table describes the information and the limit of voltage and
temperature about network card, line card and fan tray. |
| askeyHwInfoEntry | 1.3.6.1.4.1.3646.1300.2.15.1.1 | | not-accessible | |
| INT askeyHwInfoType | 1.3.6.1.4.1.3646.1300.2.15.1.1.1 | INTEGER | not-accessible | This object describes the measure value about rotation speed of fan,
voltage or temperature of the equipment include network card, line
card, and fan tray. |
| INT askeyHwSensorId | 1.3.6.1.4.1.3646.1300.2.15.1.1.2 | INTEGER | not-accessible | This object describes the index that mapping to the sensor
of the hardware device:
on the network card, there is 1 max6652; on the line card, there
are 2 max6652s with 8 sensor, and each chip has 4 sensors
to measure the voltage. |
| STR askeyHwSensorDescription | 1.3.6.1.4.1.3646.1300.2.15.1.1.3 | DisplayString | read-only | This object describes the sensor on the nc or lc |
| INT askeyHwValue | 1.3.6.1.4.1.3646.1300.2.15.1.1.4 | INTEGER | read-only | This object describes the value of hardware on the nc or lc |
| INT askeyHwRefValue | 1.3.6.1.4.1.3646.1300.2.15.1.1.5 | INTEGER | read-only | This object describes the reference value of hardware on the nc or lc |
| INT askeyHwValueThreshholdLow | 1.3.6.1.4.1.3646.1300.2.15.1.1.6 | INTEGER | read-only | This object describes the low-bound value of the
voltage on the nc or lc. If the measured value is lower
than the value, the system will report the alarm. |
| INT askeyHwValueThreshholdHigh | 1.3.6.1.4.1.3646.1300.2.15.1.1.7 | INTEGER | read-only | This object describes the high-bound value of the
voltage on the nc or lc. If the measured value is
higher than the value, the system will report the
alarm. |
| sensorThresholds | 1.3.6.1.4.1.3646.1300.2.15.2 | | | |
| INT sensorTempHigh | 1.3.6.1.4.1.3646.1300.2.15.2.1 | INTEGER | read-write | The threshold for temperature up bound. Its range is from
-20 C to 100 C |
| INT sensorTempLow | 1.3.6.1.4.1.3646.1300.2.15.2.2 | INTEGER | read-write | The threshold for temperature low bound. Its range is from
-20 C to 100 C |
| gbicModuleTable | 1.3.6.1.4.1.3646.1300.2.15.3 | | not-accessible | GBIC module information |
| gbicModuleTableEntry | 1.3.6.1.4.1.3646.1300.2.15.3.1 | | not-accessible | |
| INT gbicIdentifier | 1.3.6.1.4.1.3646.1300.2.15.3.1.1 | INTEGER | read-only | This object describes the identifier value specifies the physical
device described by the serial information.
A value 3 means SFP. |
| INT gbicConnector | 1.3.6.1.4.1.3646.1300.2.15.3.1.2 | INTEGER | read-only | The connector value indicates the external connector provided on the interface.
A value 1 means SC.
A value 7 means LC. |
| U32 gbicTransceiver | 1.3.6.1.4.1.3646.1300.2.15.3.1.3 | Unsigned32 | read-only | This object describes the gigabit ethernet compliance codes.The following bit
significant indicators define the electronic or optical interfaces that are
supported by the GBIC.
6 -
IEEE ethernet standard:
bit 0 - 1000BASE-SX
1 - 1000BASE-LX
2 - 1000BASE-CX
3 - 1000BASE-Tn
7 -
bit 0 - electrical inter-enclosure(EL)
1 - longwave laser(LC)
distance capability:
bit 4 - long distance(L)
5 - intermediate distance(I)
6 - short distance(S)
7 - very long distance(V)
8 -
SONET compliance codes:
bit 4 - longwave laser(LL)
5 - shortwave laser w/OFC(SL)
6 - shortwave laser w/o OFC(SN)
7 - intra-enclosure (EL)
9 -
transmission media type:
bit 0 - single mode(SM)
2 - multi-mode-50m(M5)
3 - multi-mode-62.5m(M6)
4 - video coax(TV)
5 - miniature coax(MI)
6 - shielded twisted pair(TP)
7 - twin axial pair(TW)
10 -
fibre channel link length:
bit 0 - 100MBytes/Sec
2 - 200MBytes/Sec
4 - 400MBytes/Sec |
| INT gbicEncoding | 1.3.6.1.4.1.3646.1300.2.15.3.1.4 | INTEGER | read-only | The encoding value indicates the serial encoding mechanism that is
the nominal design target of the particular GBIC.
value 0 - Unspecified
1 - 8B10B
2 - 4B5B
3 - NRZ
4 - Manchester
5 - SONET Scrambled |
| INT gbicBrNominal | 1.3.6.1.4.1.3646.1300.2.15.3.1.5 | INTEGER | read-only | The nominal bit rate (BR, nominal) is specified in units of 100 Megabits
per second, rounded off to the nearest 100 Megabits per second. The bit
rate includes those bits necessary to encode and delimit the signal as
well as those bits carrying data information. A value of 0 indicates that
the bit rate is not specified and must be determined from the transceiver
technology. The actual information transfer rate will depend on the encoding
of the data, as defined by the encoding value. |
| INT gbicLength9um | 1.3.6.1.4.1.3646.1300.2.15.3.1.6 | INTEGER | read-only | This value specifies the link length that is supported by the GBIC while
operating in compliance with the applicable standards using single mode
fiber.The value is in units of 100 meters. A value of 255 means that the
GBIC supports a link length greater than 25.4 km. A value of zero means
that the GBIC does not support single mode fiber or that the length
information must be determined from the transceiver technology. |
| INT gbicLength50um | 1.3.6.1.4.1.3646.1300.2.15.3.1.7 | INTEGER | read-only | This value specifies the link length that is supported by the GBIC while
operating in compliance with the applicable standards using 50 micron
multi-mode fiber. The value is in units of 10 meters. A value of 255
means that the GBIC supports a link length greater than 2.54 km. A value
of zero means that the GBIC does not support 50 micron multi-mode fiber or
that the length information must be determined from the transceiver technology. |
| INT gbicLength62_5um | 1.3.6.1.4.1.3646.1300.2.15.3.1.8 | INTEGER | read-only | This value specifies the link length that is supported by the GBIC while operating in compliance with the applicable standards using 62.5 micron multi-mode fiber. The value is in units of 10 meters. A value of 255 means that the GBIC supports a link length greater than 2.54 km. A value of zero means that the GBIC does not 62.5 micron multi-mode fiber or that the length information must determined from the transceiver technology. It is common for GBICs to support both 50 micron and 62.5 micron fiber. |
| INT gbicCopperLength | 1.3.6.1.4.1.3646.1300.2.15.3.1.9 | INTEGER | read-only | This value specifies the minimum link length that is supported by the GBIC
while operating in compliance with the applicable standards using copper
cable. The value is in units of 1 meter. A value of 255 means that the GBIC
supports a link length greater than 254 meters. A value of zero means that
the GBIC does not support copper cables or that the length information must
be determined from the transceiver technology. Further information about the
cable design, equalization, and connectors is usually required to guarantee
meeting a particular length requirement. |
| STR gbicVendorName | 1.3.6.1.4.1.3646.1300.2.15.3.1.10 | DisplayString | read-only | The vendor name is a 16 character field that contains ASCII characters,
left-aligned and padded on the right with ASCII spaces (20h). The vendor
name shall be the full name of the corporation, a commonly accepted
abbreviation of the name of the corporation, the SCSI company code for the
corporation, or the stock exchange code for the corporation. At least one
of the vendor name or the vendor OUI fields shall contain valid serial data. |
| U32 gbicVendorOUI | 1.3.6.1.4.1.3646.1300.2.15.3.1.11 | Unsigned32 | read-only | The vendor organizationally unique identifier field (vendor OUI) is a 3-byte
field that contains the IEEE Company Identifier for the vendor. A value of
all zero in the 3-byte field indicates that the Vendor OUI is unspecified. |
| STR gbicVendorPN | 1.3.6.1.4.1.3646.1300.2.15.3.1.12 | DisplayString | read-only | The vendor part number (vendor PN) is a 16-byte field that contains ASCII
characters, left-aligned and padded on the right with ASCII spaces (20h),
defining the vendor part number or product name. A value of all zero in
the 16-byte field indicates that the vendor PN is unspecified. |
| U32 gbicVendorSN | 1.3.6.1.4.1.3646.1300.2.15.3.1.13 | Unsigned32 | read-only | The vendor serial number (vendor SN) is a 16 character field that contains ASCII
characters, left-aligned and padded on the right with ASCII spaces (20h),
defining the vendor's serial number for the GBIC. A value of all zero in the
16-byte field indicates that the vendor PN is unspecified. |
| INT gbicLaserWaveLength | 1.3.6.1.4.1.3646.1300.2.15.3.1.14 | INTEGER | read-only | This object describes the fibre channel transmitter wave laser length(nm). |
