AP80-PRIVATE-MIB

All MIBs › AP80-PRIVATE-MIB

Category: Wireless and WLAN

Description: Aironet AP80 proprietary wireless access point radio and association management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AP80-PRIVATE-MIB?

AP80-PRIVATE-MIB is a proprietary MIB for the Aironet AP80 wireless access point, an early product from Aironet Wireless Communications (later acquired into the Cisco Aironet line). It exposes device identification and firmware version objects, serial console line configuration, a port table, and a system-notification tree for traps. Its monitoring value strongly emphasizes hardware/software inventory status: hardware revision, boot ROM version, and operating-code (firmware) version let an admin verify exactly what's running on the AP and identify units overdue for a firmware upgrade, while the line/port tables expose serial console settings used for out-of-band management. It is a standalone, vendor-proprietary MIB that predates Cisco's later standardized access-point MIBs. It is deployed on legacy Aironet AP80 units in enterprise wireless LAN deployments, where AP80-PRIVATE-MIB SNMP monitoring is often still used to track firmware currency ahead of eventual replacement.

IPNetwork Monitor allows you to monitor SNMP objects defined in AP80-PRIVATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aruba Networks outdoor wireless access point (Accton-manufactured, legacy)

Monitoring Examples

Polling swHardwareVer, swBootRomVer, swOpCodeVer, and swSerialNumber gives an inventory snapshot of an AP80's hardware revision, boot ROM version, and firmware (operating code) version, useful for identifying units that need a firmware upgrade. lineTable/lineEntry (lineIndex, lineDataBits, lineParity, lineSpeed, lineStopBits) exposes the serial console line configuration for out-of-band access, and sysNotifications carries device-generated traps for status-change events.

What Can Be Monitored

hardware version
boot ROM version
operating code (firmware) version
device serial number
serial console line settings
system notifications/traps

Imported Objects

From RFC1155-SMI

Counter
IpAddress
enterprises
mgmt

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Integer32

OIDs

OID symbolic	OID numeric	Type	Access	Description
aruba	1.3.6.1.4.1.14823
arubaAp	1.3.6.1.4.1.14823.2.3
arubaEnterpriseMibModules	1.3.6.1.4.1.14823.2
INT deleteMacAddr	1.3.6.1.4.1.14823.2.3.2.10.5.3.1.3	INTEGER	read-write	To delete the MAC Address from Uplink Port MAC Address Filter Table. Delete(1) To start delete MAC address. Nothing(2) Nothing occur.
STR destFile	1.3.6.1.4.1.14823.2.3.2.4.4	DisplayString	read-write	The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
INT dot118021xBroadcastKeyRefreshRate	1.3.6.1.4.1.14823.2.3.2.7.1.2	INTEGER	read-write	The number (in minutes) between changing the broadcast key for 802.1x and WPA clients
INT dot118021xReauthenticationTimeout	1.3.6.1.4.1.14823.2.3.2.7.1.4	INTEGER	read-write	The number (in minutes) between forcing 802.1x clients to reauthenticate
INT dot118021xSessionKeyRefreshRate	1.3.6.1.4.1.14823.2.3.2.7.1.3	INTEGER	read-write	The number (in minutes) between changing session keys for 802.1x and WPA clients
INT dot118021xState	1.3.6.1.4.1.14823.2.3.2.7.1.1	INTEGER	read-write	This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm.
I32 dot118021xSuppIndex	1.3.6.1.4.1.14823.2.3.2.7.5.1.1	Integer32	not-accessible	Index of the interface for which this supplicant is running. Currently only the ethernet interface.
STR dot118021xSuppPasswd	1.3.6.1.4.1.14823.2.3.2.7.5.1.4	DisplayString	read-write	This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY.
INT dot118021xSuppState	1.3.6.1.4.1.14823.2.3.2.7.5.1.2	INTEGER	read-write	This object is used to enable or disable the 802.1x supplicant.
STR dot118021xSuppUser	1.3.6.1.4.1.14823.2.3.2.7.5.1.3	DisplayString	read-write	This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY.
INT dot11AckFailuresTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.25	INTEGER	read-write	This value indicates whether the dot11AckFailuresTrapEnabled trap is enabled.
IP dot11ApIpAddress	1.3.6.1.4.1.14823.2.3.2.7.4.1.5	IpAddress	not-accessible	This value indicates the IP address of the Access Point
INT dot11AuthenticationAcctInterimUpdate	1.3.6.1.4.1.14823.2.3.2.7.2.1.8	INTEGER	read-write	This value indicates the Timeout value(sec) used by the radius server interim update.
INT dot11AuthenticationAcctPort	1.3.6.1.4.1.14823.2.3.2.7.2.1.7	INTEGER	read-write	The port number for radius server accounting.
dot11AuthenticationEntry	1.3.6.1.4.1.14823.2.3.2.7.1
STR dot11AuthenticationKey	1.3.6.1.4.1.14823.2.3.2.7.2.1.4	DisplayString	read-write	This value indicates the shared key used by the authentication server.
INT dot11AuthenticationMACAddressFormat	1.3.6.1.4.1.14823.2.3.2.7.2.1.9	INTEGER	read-write	This value indicates the MAC address format from Radius MAC authentication. no-delimiter format: aabbccddeeff single-dash format: aabbcc-ddeeff multi-dash format: aa-bb-cc-dd-ee-ff multi-colon format: aa:bb:cc:dd:ee:ff
INT dot11AuthenticationPort	1.3.6.1.4.1.14823.2.3.2.7.2.1.3	INTEGER	read-write	This value indicates the UDP Port used by the authentication server.
INT dot11AuthenticationRetransmit	1.3.6.1.4.1.14823.2.3.2.7.2.1.5	INTEGER	read-write	This value indicates the retransmit timer length used by the authentication server.
IP dot11AuthenticationServer	1.3.6.1.4.1.14823.2.3.2.7.2.1.2	IpAddress	read-write	This value indicates the IP address of the authentication server.
dot11AuthenticationServerEntry	1.3.6.1.4.1.14823.2.3.2.7.2.1		not-accessible	An entry in the table, containing information about configuration of one authentication server of the AP.
I32 dot11AuthenticationServerIndex	1.3.6.1.4.1.14823.2.3.2.7.2.1.1	Integer32	not-accessible	Index of the Authentication Server
dot11AuthenticationServerTable	1.3.6.1.4.1.14823.2.3.2.7.2		not-accessible	Table of descriptive and status information about configuration of each authentication server.
dot11AuthenticationSupplicantEntry	1.3.6.1.4.1.14823.2.3.2.7.5.1		not-accessible	An entry in the table, containing information about configuration of one supplicant.
dot11AuthenticationSupplicantTable	1.3.6.1.4.1.14823.2.3.2.7.5		not-accessible	Table of descriptive and status information about configuration of supplicant
INT dot11AuthenticationTimeout	1.3.6.1.4.1.14823.2.3.2.7.2.1.6	INTEGER	read-write	This value indicates the Timeout value(sec) used by the authentication server.
INT dot11AuthenticationVLANIDFormat	1.3.6.1.4.1.14823.2.3.2.7.2.1.10	INTEGER	read-write	This value indicates the VLAN ID format from Radius server.
INT dot11FailedTransmitsTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.24	INTEGER	read-write	This value indicates whether the dot11FailedTransmitsTrapEnabled trap is enabled.
INT dot11FcsErrorsTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.26	INTEGER	read-write	This value indicates whether the dot11FcsErrorsTrapEnabled trap is enabled.
MAC dot11FilterAddress	1.3.6.1.4.1.14823.2.3.2.7.3.2.1.1	MacAddress	not-accessible	This value indicates the MAC address of the filter entry.
INT dot11FilterDefault	1.3.6.1.4.1.14823.2.3.2.7.3.1	INTEGER	read-write	This value indicates the default access for local mac filters.
dot11FilterEntry	1.3.6.1.4.1.14823.2.3.2.7.3.2.1		not-accessible	An entry in the table, containing information about configuration in one radio of the AP.
INT dot11FilterStatus	1.3.6.1.4.1.14823.2.3.2.7.3.2.1.2	INTEGER	read-write	This value indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.
dot11FilterTable	1.3.6.1.4.1.14823.2.3.2.7.3.2		not-accessible	Table of status information about each configured MAC Address Filtering Entry.
NTF dot11InterfaceAGFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.6			The InterfaceAGFail notification shall be sent out when 802.11a/802.11g wireless interface has failed.
INT dot11InterfaceAGFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.10	INTEGER	read-write	This value indicates whether the dot11InterfaceAGFail trap is enabled.
NTF dot11InterfaceBFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.5			The InterfaceBFail notification shall be sent out when 802.11b wireless interface has failed.
INT dot11InterfaceBFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.9	INTEGER	read-write	This value indicates whether the dot11InterfaceBFail trap is enabled.
MAC dot11MacAddr	1.3.6.1.4.1.14823.2.3.2.7.4.1.1	MacAddress	not-accessible	Mac Address of the affected interface, returned with traps only.
dot11MACAuthenticationFilter	1.3.6.1.4.1.14823.2.3.2.7.3
INT dot11MACAuthenticationType	1.3.6.1.4.1.14823.2.3.2.7.1.5	INTEGER	read-write	This value indicates the type of mac authentication in use.
dot11NotificationObjects	1.3.6.1.4.1.14823.2.3.2.7.4.1
dot11Notifications	1.3.6.1.4.1.14823.2.3.2.7.4.2
dot11NotificationTree	1.3.6.1.4.1.14823.2.3.2.7.4
INT dot11ReasonCode	1.3.6.1.4.1.14823.2.3.2.7.4.1.4	INTEGER	not-accessible	This attribute defines the reason for the failure of an operation. Value = 1: Invalid mode/state Value = 2: Station not authenticated. Value = 3: Internal error Value = 4: Out of sequence frame Value = 5: Un-supportd algorithm Value = 6: Invalid frame length Value = 7: WEP is required on the AP Value = 8: WEP not allowed Value = 9: Challenge text mismatch
INT dot11RequestType	1.3.6.1.4.1.14823.2.3.2.7.4.1.3	INTEGER	not-accessible	This attribute defines the request type sent by the station. Value = 1: Unknown request type Value = 2: Association Request Value = 3: Re-association Request Value = 4: Authentication
MAC dot11Station	1.3.6.1.4.1.14823.2.3.2.7.4.1.2	MacAddress	not-accessible	This attribute holds the MAC address of the wireless station
NTF dot11StationAssociation	1.3.6.1.4.1.14823.2.3.2.7.4.2.1			The associate notification shall be sent when a station successfully associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
INT dot11StationAssociationTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.5	INTEGER	read-write	This value indicates whether the dot11StationAssociation trap is enabled.
NTF dot11StationAuthentication	1.3.6.1.4.1.14823.2.3.2.7.4.2.3			The authentication notification shall be sent when a station successfully authenticates with the Access Point. The value of the notification shall include the MAC address of the station that has authenticated.
INT dot11StationAuthenticationTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.7	INTEGER	read-write	This value indicates whether the dot11StationAuthentication trap is enabled.
NTF dot11StationReAssociation	1.3.6.1.4.1.14823.2.3.2.7.4.2.2			The re-associate notification shall be sent when a station successfully re-associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
INT dot11StationReAssociationTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.6	INTEGER	read-write	This value indicates whether the dot11StationReAssociation trap is enabled.
NTF dot11StationRequestFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.4			The station request fail shall be sent out when a station fails to associate / re-associate / authenticate with the Access Point. The notification shall include the MAC address of the station and the reason code for the failure.
INT dot11StationRequestFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.8	INTEGER	read-write	This value indicates whether the dot11StationRequestFail trap is enabled.
INT dot11Vap8021xBroadcastKeyRefreshRate	1.3.6.1.4.1.14823.2.3.2.7.6.1.3	INTEGER	read-write	The number (in minutes) between changing the broadcast key for 802.1x and WPA clients
I32 dot11Vap8021xIndex	1.3.6.1.4.1.14823.2.3.2.7.6.1.1	Integer32	not-accessible	Index for configuration.
INT dot11Vap8021xReauthenticationTimeout	1.3.6.1.4.1.14823.2.3.2.7.6.1.5	INTEGER	read-write	The number (in minutes) between forcing 802.1x clients to reauthenticate
INT dot11Vap8021xSessionKeyRefreshRate	1.3.6.1.4.1.14823.2.3.2.7.6.1.4	INTEGER	read-write	The number (in minutes) between changing session keys for 802.1x and WPA clients
INT dot11Vap8021xState	1.3.6.1.4.1.14823.2.3.2.7.6.1.2	INTEGER	read-write	This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm.
dot11VapAuthenticationEntry	1.3.6.1.4.1.14823.2.3.2.7.6.1		not-accessible	An entry in the table, containing information about configuration of 8021x for each Vap of the AP.
dot11VapAuthenticationTable	1.3.6.1.4.1.14823.2.3.2.7.6		not-accessible	Table of descriptive and status information about configuration of 8021x for each Vap.
INT dot11VapAuthMACAuthenticationTimeout	1.3.6.1.4.1.14823.2.3.2.7.6.1.7	INTEGER	read-write	The number (in minutes) between forcing Radius MAC to authenticate.
INT dot11VapAuthMACAuthenticationType	1.3.6.1.4.1.14823.2.3.2.7.6.1.6	INTEGER	read-write	This value indicates the type of mac authentication in use.
MAC dot1xAuthenticatorMacAddr	1.3.6.1.4.1.14823.2.3.2.7.4.1.6	MacAddress	not-accessible	This attribute holds the MAC address of the authenticator for the AP.
NTF dot1xAuthFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.11			The 802.1x authentication failure notification shall be sent when a station fails to authenticate with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
INT dot1xAuthFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.15	INTEGER	read-write	This value indicates whether the dot1xAuthFail trap is enabled.
NTF dot1xAuthNotInitiated	1.3.6.1.4.1.14823.2.3.2.7.4.2.9			The 802.1x authentication not initiated notification shall be sent when a station did not initiate 802.1x authentication with the RADIUS server. The value of the notification shall include the MAC address of the station that did not initiate 802.1x authentication.
INT dot1xAuthNotInitiatedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.13	INTEGER	read-write	This value indicates whether the dot1xAuthNotInitiated trap is enabled.
NTF dot1xAuthSuccess	1.3.6.1.4.1.14823.2.3.2.7.4.2.10			The 802.1x authentication success notification shall be sent when a station successfully authenticates with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
INT dot1xAuthSuccessTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.14	INTEGER	read-write	This value indicates whether the dot1xAuthSuccess trap is enabled.
NTF dot1xMacAddrAuthFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.8			The 802.1x MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
INT dot1xMacAddrAuthFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.12	INTEGER	read-write	This value indicates whether the dot1xMacAddrAuthFail trap is enabled.
NTF dot1xMacAddrAuthSuccess	1.3.6.1.4.1.14823.2.3.2.7.4.2.7			The 802.1x MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
INT dot1xMacAddrAuthSuccessTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.11	INTEGER	read-write	This value indicates whether the dot1xMacAddrAuthSuccess trap is enabled.
INT dot1xSuppAuthenticatedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.23	INTEGER	read-write	This value indicates whether the dot1xSupplicantAuthenticated trap is enabled.
NTF dot1xSupplicantAuthenticated	1.3.6.1.4.1.14823.2.3.2.7.4.2.18			The notification shall be sent when the AP has successfully authenticated with the switch. The value of the notification shall include the MAC address of the switch (authenticator) that the AP has authenticated with.
enterpriseApAdmin	1.3.6.1.4.1.14823.2.3.2.8
STR enterpriseApAdminPassword	1.3.6.1.4.1.14823.2.3.2.8.2	DisplayString	read-write	This value indicates the password for management login. The password length is betwen 3 and 16. 'Zero-length' indicates 'no password'.
STR enterpriseApAdminUser	1.3.6.1.4.1.14823.2.3.2.8.1	DisplayString	read-write	This value indicates the username for management login.
enterpriseApDNS	1.3.6.1.4.1.14823.2.3.2.12
IP enterpriseApDNSPrimaryServer	1.3.6.1.4.1.14823.2.3.2.12.1	IpAddress	read-write	This value indicates the IP address of the primary DNS server.
IP enterpriseApDNSSecondaryServer	1.3.6.1.4.1.14823.2.3.2.12.2	IpAddress	read-write	This value indicates the IP address of the secondary DNS server.
enterpriseAPdot11	1.3.6.1.4.1.14823.2.3.2.7
enterpriseApFileTransferMgt	1.3.6.1.4.1.14823.2.3.2.4
enterpriseApFilterControl	1.3.6.1.4.1.14823.2.3.2.10
INT enterpriseApFilterControlAPManage	1.3.6.1.4.1.14823.2.3.2.10.2	INTEGER	read-write	This value indicates the AP management filter setting.
INT enterpriseApFilterControlEthernet	1.3.6.1.4.1.14823.2.3.2.10.3	INTEGER	read-write	This value indicates the ethernet filter setting.
INT enterpriseApFilterControlInterClientSTAsCommun	1.3.6.1.4.1.14823.2.3.2.10.1	INTEGER	read-write	This value indicates the Inter Client STAs Communication Filter setting. disabled (1) To disable the Inter Client STAs Communication Filter PreventIntraVAPClient (2) To set filter to prevent intra VAP client communication PreventInterAndIntraVAPClient(3) To set filter to prevent inter and intra VAP client communication
enterpriseApFilterProtocolEntry	1.3.6.1.4.1.14823.2.3.2.10.4.1		not-accessible	An entry in the filter protocol table, containing information about configuration of one filter table entry.
I32 enterpriseApFilterProtocolIndex	1.3.6.1.4.1.14823.2.3.2.10.4.1.1	Integer32	not-accessible	Index of the Protocol Filters.
STR enterpriseApFilterProtocolISODesignator	1.3.6.1.4.1.14823.2.3.2.10.4.1.3	DisplayString	read-only	This value indicates the name of the protocol filter.
STR enterpriseApFilterProtocolName	1.3.6.1.4.1.14823.2.3.2.10.4.1.2	DisplayString	read-only	This value indicates the name of the protocol filter. One of the following: Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation, CDP, DEC_LAT, DEC_MOP, DEC_MOP_Dump_Load, DEC_XNS, EAPOL, Enet_Config_Test, Ethertalk, IP, LAN_Test, NetBEUI, Novell_IPX(new), Novell_IPX(old), RARP, Telxon_TXP, X.25_Level3
INT enterpriseApFilterProtocolState	1.3.6.1.4.1.14823.2.3.2.10.4.1.4	INTEGER	read-write	This value indicates whether the protocol filter is enabled.
enterpriseApFilterProtocolTable	1.3.6.1.4.1.14823.2.3.2.10.4		not-accessible	Table of descriptive and status information about configuration of the filter protocol table.
enterpriseApFilterUplinkPortMACAddrFilter	1.3.6.1.4.1.14823.2.3.2.10.5
enterpriseApIpMgt	1.3.6.1.4.1.14823.2.3.2.6
enterpriseApLineMgnt	1.3.6.1.4.1.14823.2.3.2.2
enterpriseApNativeVlanEntry	1.3.6.1.4.1.14823.2.3.2.9.3.1		not-accessible	An entry in the table, containing information about vlan configuration of one wireless interface.
enterpriseApNativeVlanTable	1.3.6.1.4.1.14823.2.3.2.9.3		not-accessible	Table used to manage the Vlans for each wireless interface.
enterpriseApPortMgnt	1.3.6.1.4.1.14823.2.3.2.3
enterpriseApRadio	1.3.6.1.4.1.14823.2.3.2.15
INT enterpriseApRadioAntennaControlMethod	1.3.6.1.4.1.14823.2.3.2.15.1.1.14	INTEGER	read-write	This value indicates the antenna control method for the radio index. Diversity(1) AP select the antenna automatically. Left (2) Use the left antenna. Right (3) Use the right antenna.
I32 enterpriseApRadioAntennaGainReduction	1.3.6.1.4.1.14823.2.3.2.15.1.1.28	Integer32	read-write	This value indicates the antenna gain reduction for the radio index.(unit: dB)
STR enterpriseApRadioAntennaId	1.3.6.1.4.1.14823.2.3.2.15.1.1.13	DisplayString	read-only
INT enterpriseApRadioAntennaLocation	1.3.6.1.4.1.14823.2.3.2.15.1.1.15	INTEGER	read-write	This value indicates the location of antenna for each radio index.
INT enterpriseApRadioAntennaMode	1.3.6.1.4.1.14823.2.3.2.15.1.1.12	INTEGER	read-write	This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: fixed(1) means use both built-in antennas, external(2) means use one external antenna on the right side. This setting is only valid for the 802.11g interface.
INT enterpriseApRadioAutoChannel	1.3.6.1.4.1.14823.2.3.2.15.1.1.3	INTEGER	read-write	This value indicates whether auto channel selection is enabled or not for this radio interface
I32 enterpriseApRadioBeaconInterval	1.3.6.1.4.1.14823.2.3.2.15.1.1.23	Integer32	read-write	This value indicates the beacon interval for this radio index.
I32 enterpriseApRadioChannel	1.3.6.1.4.1.14823.2.3.2.15.1.1.25	Integer32	read-write	This valud indicates the radio channel for the radio index. set channel 42/50/58/152/160 for static turbo mode, set channel 40/48/56/153/161 for dynamic turbo mode, set channel 36/40/44/48/52/56/60/64/149/153/157/161/165 when turbo mode is disabled. The value '0' indicates the radio interface cannot be enable in current country code.
INT enterpriseApRadioClosedSystem	1.3.6.1.4.1.14823.2.3.2.15.1.1.5	INTEGER	read-write	This value indicates whether closed system is enabled for this radio interface.
I32 enterpriseApRadioDataBeaconRate	1.3.6.1.4.1.14823.2.3.2.15.1.1.24	Integer32	read-write	This value indicates the data beacon rate for the radio index.
INT enterpriseApRadioDataRate	1.3.6.1.4.1.14823.2.3.2.15.1.1.10	INTEGER	read-write	This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed data rates. The auto setting will attempt to set the best data rate for the interface
STR enterpriseApRadioDescription	1.3.6.1.4.1.14823.2.3.2.15.1.1.9	DisplayString	read-write	This value indicates the description for this radio interface.
enterpriseApRadioEntry	1.3.6.1.4.1.14823.2.3.2.15.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 enterpriseApRadioFragmentLength	1.3.6.1.4.1.14823.2.3.2.15.1.1.26	Integer32	read-write	This value indicates the fragment length for the radio index.(unit: Byte)
INT enterpriseApRadioGMode	1.3.6.1.4.1.14823.2.3.2.15.1.1.11	INTEGER	read-write	This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface.
I32 enterpriseApRadioIndex	1.3.6.1.4.1.14823.2.3.2.15.1.1.1	Integer32	not-accessible	Radio Index for configuration.
INT enterpriseApRadioMaxAssoc	1.3.6.1.4.1.14823.2.3.2.15.1.1.6	INTEGER	read-write	This value indicates the max number of clients allowed on this radio interface.
INT enterpriseApRadioMICMode	1.3.6.1.4.1.14823.2.3.2.15.1.1.21	INTEGER	read-write	This value indicates the MIC mode status for this radio index. software(1) To set MIC mode to software. hardware(2) To set MIC mode to hardware.
INT enterpriseApRadioRogueApDetection	1.3.6.1.4.1.14823.2.3.2.15.1.1.16	INTEGER	read-write	The status of Rogue AP detection for each index. enabled(1) To set rogue Ap detection enabled. disabled(2) To set rogue Ap detection disabled.
I32 enterpriseApRadioRogueApScanDuration	1.3.6.1.4.1.14823.2.3.2.15.1.1.18	Integer32	read-write	This value indicates the rogue AP scan duratoin.(unit: minutes)
I32 enterpriseApRadioRogueApScanInterval	1.3.6.1.4.1.14823.2.3.2.15.1.1.17	Integer32	read-write	This value indicates the interval between each rogue AP scan.(unit: minutes)
INT enterpriseApRadioRogueApScanNow	1.3.6.1.4.1.14823.2.3.2.15.1.1.19	INTEGER	read-write	To force Ap to do rogue AP scan right away. enabled(1) To do Rogue AP scan right now. disabled(2) To set rogue Ap.
I32 enterpriseApRadioRTSThreshold	1.3.6.1.4.1.14823.2.3.2.15.1.1.27	Integer32	read-write	This value indicates the RTS Threshold for the radio index.(unit: Byte)
INT enterpriseApRadioState	1.3.6.1.4.1.14823.2.3.2.15.1.1.2	INTEGER	read-write	This value indicates the state of the radio interface.
INT enterpriseApRadioSuperMode	1.3.6.1.4.1.14823.2.3.2.15.1.1.22	INTEGER	read-write	This value indicates the super mode status for this radio index. enabled (1) To set super mode enabled. disabled(2) To set super mode disabled.
enterpriseApRadioTable	1.3.6.1.4.1.14823.2.3.2.15.1		not-accessible	Table of descriptive and status information about configuration of each radio.
INT enterpriseApRadioTransmitKey	1.3.6.1.4.1.14823.2.3.2.15.1.1.7	INTEGER	read-write	This value indicates default transmit key in use for this radio interface.
INT enterpriseApRadioTransmitPower	1.3.6.1.4.1.14823.2.3.2.15.1.1.4	INTEGER	read-write	This value indicates the transmit power for this radio interface.
INT enterpriseApRadioTurboMode	1.3.6.1.4.1.14823.2.3.2.15.1.1.8	INTEGER	read-write	This value indicates whether turbo mode is enabled for this radio interface.
enterpriseApRadioWds	1.3.6.1.4.1.14823.2.3.2.22
enterpriseApRadioWdsEntry	1.3.6.1.4.1.14823.2.3.2.22.1.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable). The table does not contain the radio index as a member of the table.
enterpriseApRadioWdsPeerEntry	1.3.6.1.4.1.14823.2.3.2.22.2.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable) and the peer index (Up to 8). The table does not contain the radio index as a member of the table.
enterpriseApRadioWdsPeerTable	1.3.6.1.4.1.14823.2.3.2.22.2		not-accessible	Table of configuration information for Wds Peers for each Radio interface.
enterpriseApRadioWdsTable	1.3.6.1.4.1.14823.2.3.2.22.1		not-accessible	Table of configuration information for Wds for each Radio interface.
enterpriseApResetMgt	1.3.6.1.4.1.14823.2.3.2.5
enterpriseApSecurity	1.3.6.1.4.1.14823.2.3.2.14
INT enterpriseApSecurityAuthType	1.3.6.1.4.1.14823.2.3.2.14.1.1.2	INTEGER	read-write	This value indicates the type of authentication in use for this radio interface. opensystem(0) Set authentication open sharedkey(1) Set authentication shared wpa(2) Set WPA Mode wpapsk(3) Set WPA-PSK Mode wpa-wpa2-mixed(4) Set WPA-WPA2-Mixed Mode wpawpa2pskmixed(5) Set WPA-WPA2 PSK Mixed Mode wpa2(6) Set WPA2 Mode wpa2psk(7) Set WPA2-PSK Mode
enterpriseApSecurityEntry	1.3.6.1.4.1.14823.2.3.2.14.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 enterpriseApSecurityIndex	1.3.6.1.4.1.14823.2.3.2.14.1.1.1	Integer32	not-accessible	Radio Index for security settings.
INT enterpriseApSecuritySharedKeyLen	1.3.6.1.4.1.14823.2.3.2.14.1.1.3	INTEGER	read-only	This value indicates the shared key length for this radio interface.
enterpriseApSecurityTable	1.3.6.1.4.1.14823.2.3.2.14.1		not-accessible	Table of descriptive and status information about configuration of each radio in terms of security settings.
T/F enterpriseApSecurityWEPEnabled	1.3.6.1.4.1.14823.2.3.2.14.1.1.10	TruthValue	read-write	This value indicates whether WEP is enabled.
INT enterpriseApSecurityWEPKeyType	1.3.6.1.4.1.14823.2.3.2.14.1.1.9	INTEGER	read-write	This value indicates the type of WEP Key in use for this radio interface.
INT enterpriseApSecurityWPACipher	1.3.6.1.4.1.14823.2.3.2.14.1.1.6	INTEGER	read-write	This value indicates the type of WPA Cipher in use for this radio interface.
INT enterpriseApSecurityWPACipherSuite	1.3.6.1.4.1.14823.2.3.2.14.1.1.11	INTEGER	read-write	This value indicates the type of WPA Cipher Suite in use for this radio interface.
INT enterpriseApSecurityWPAKeyType	1.3.6.1.4.1.14823.2.3.2.14.1.1.5	INTEGER	read-write	This value indicates the type of WPA Key Management in use for this radio interface.
INT enterpriseApSecurityWPAMode	1.3.6.1.4.1.14823.2.3.2.14.1.1.4	INTEGER	read-write	This value indicates the state of WPA for this radio interface.
INT enterpriseApSecurityWPAPmksaLifetime	1.3.6.1.4.1.14823.2.3.2.14.1.1.13	INTEGER	read-write	The number (in minutes) for Pmksa-Lifetime.
INT enterpriseApSecurityWPAPreAuthentication	1.3.6.1.4.1.14823.2.3.2.14.1.1.12	INTEGER	read-write	Whether Pre-Authentication is enabled.
STR enterpriseApSecurityWPAPSK	1.3.6.1.4.1.14823.2.3.2.14.1.1.8	DisplayString	read-write	This value indicates WPA Pre Shared Key in use for this radio interface.
INT enterpriseApSecurityWPAPSKType	1.3.6.1.4.1.14823.2.3.2.14.1.1.7	INTEGER	read-write	This value indicates the type of WPA Pre Shared Key in use for this radio interface.
enterpriseApSession	1.3.6.1.4.1.14823.2.3.2.17
T/F enterpriseApSessionAssociated	1.3.6.1.4.1.14823.2.3.2.17.1.1.4	TruthValue	read-only	Whether the session is associated or not. It is rare case that not associated stations show up in the table.
TIK enterpriseApSessionAssociatedTime	1.3.6.1.4.1.14823.2.3.2.17.1.1.9	TimeTicks	read-only	This is the time in hundredths of a second since the client associated. The value is related to the system startup
I32 enterpriseApSessionAssociationId	1.3.6.1.4.1.14823.2.3.2.17.1.1.7	Integer32	read-only	The internal association identify number
T/F enterpriseApSessionAuthenticated	1.3.6.1.4.1.14823.2.3.2.17.1.1.3	TruthValue	read-only	Whether the session is authenticated or not.
enterpriseApSessionEntry	1.3.6.1.4.1.14823.2.3.2.17.1.1		not-accessible	An entry in the table, containing information about status and statistics of the wireless station.
I32 enterpriseApSessionIfIndex	1.3.6.1.4.1.14823.2.3.2.17.1.1.1	Integer32	not-accessible	Interface index for the radio this session is associated with.
T/F enterpriseApSessionIsForwarding	1.3.6.1.4.1.14823.2.3.2.17.1.1.5	TruthValue	read-only	Whether the AP is forwarding the client station traffic (higher level authentication)
INT enterpriseApSessionKeyType	1.3.6.1.4.1.14823.2.3.2.17.1.1.6	INTEGER	read-only	The encryption key type used by the station. Note that wpa-wep is not supported
TIK enterpriseApSessionLastAssociatedTime	1.3.6.1.4.1.14823.2.3.2.17.1.1.10	TimeTicks	read-only	This is the time in hundredths of a second when the client associated in last session. The value is related to the system startup
TIK enterpriseApSessionLastAuthenticatedTime	1.3.6.1.4.1.14823.2.3.2.17.1.1.8	TimeTicks	read-only	This is the time in hundredths of a second last time the client is authenticated. Note that a session may be authenticated multiple times. The value is related to the system startup
TIK enterpriseApSessionLastDisassociatedTime	1.3.6.1.4.1.14823.2.3.2.17.1.1.11	TimeTicks	read-only	This is the time in hundredths of a second when the client disassociated in last session. The value is related to the system startup
C32 enterpriseApSessionRxByteCount	1.3.6.1.4.1.14823.2.3.2.17.1.1.15	Counter32	read-only	This is the number of unicast bytes transmitted from the AP to the client. It includes the bytes of data, control and management packets.
C32 enterpriseApSessionRxPacketCount	1.3.6.1.4.1.14823.2.3.2.17.1.1.13	Counter32	read-only	This is the number of unicast packets transmitted from the AP to the client. It includes data, control and management packets.
MAC enterpriseApSessionStationAddres	1.3.6.1.4.1.14823.2.3.2.17.1.1.2	MacAddress	not-accessible	The unique MAC Address of the station for this session.
enterpriseApSessionTable	1.3.6.1.4.1.14823.2.3.2.17.1		not-accessible	This table list all sessions (wireless stations) status
C32 enterpriseApSessionTxByteCount	1.3.6.1.4.1.14823.2.3.2.17.1.1.14	Counter32	read-only	This is the number of bytes transmitted from the client to the AP. It includes the bytes of data, control and management packets.
C32 enterpriseApSessionTxPacketCount	1.3.6.1.4.1.14823.2.3.2.17.1.1.12	Counter32	read-only	This is the number of packets transmitted from the client to the AP. It includes data, control and management packets.
enterpriseApSNMP	1.3.6.1.4.1.14823.2.3.2.16
STR enterpriseApSNMPCommunityReadOnly	1.3.6.1.4.1.14823.2.3.2.16.1	DisplayString	read-write	The SNMP Read Only Community. The value if read, will only show ******.
STR enterpriseApSNMPCommunityReadWrite	1.3.6.1.4.1.14823.2.3.2.16.2	DisplayString	read-write	The SNMP Read Write Community. The value if read, will only show *****.
STR enterpriseApSNMPTrapDestinationCommunity	1.3.6.1.4.1.14823.2.3.2.16.3.1.2	DisplayString	read-write	The SNMP Trap Community
enterpriseApSNMPTrapDestinationEntry	1.3.6.1.4.1.14823.2.3.2.16.3.1		not-accessible	An entry in the table, containing information about configuration of one trap receiving server.
INT enterpriseApSNMPTrapDestinationIndex	1.3.6.1.4.1.14823.2.3.2.16.3.1.1	INTEGER	not-accessible	Index of the Trap Destination Table.
IP enterpriseApSNMPTrapDestinationIP	1.3.6.1.4.1.14823.2.3.2.16.3.1.3	IpAddress	read-write	The IP address of the trap receiving server.
INT enterpriseApSNMPTrapDestinationState	1.3.6.1.4.1.14823.2.3.2.16.3.1.4	INTEGER	read-write	This value indicates whether the trap receiving server is enabled.
enterpriseApSNMPTrapDestinationTable	1.3.6.1.4.1.14823.2.3.2.16.3		not-accessible	Table of descriptive and status information about configuration of each trap receiving server.
enterpriseApSNMPTrapFilters	1.3.6.1.4.1.14823.2.3.2.16.4
enterpriseApSNTP	1.3.6.1.4.1.14823.2.3.2.11
INT enterpriseApSNTPDST	1.3.6.1.4.1.14823.2.3.2.11.5	INTEGER	read-write	This value indicates whether Daylight Savings Time is enabled or not.
INT enterpriseApSNTPDSTEndDay	1.3.6.1.4.1.14823.2.3.2.11.9	INTEGER	read-write	This value indicates the ending day for Daylight Savings Time.
INT enterpriseApSNTPDSTEndMonth	1.3.6.1.4.1.14823.2.3.2.11.8	INTEGER	read-write	This value indicates the ending month for Daylight Savings Time.
INT enterpriseApSNTPDSTStartDay	1.3.6.1.4.1.14823.2.3.2.11.7	INTEGER	read-write	This value indicates the starting day for Daylight Savings Time.
INT enterpriseApSNTPDSTStartMonth	1.3.6.1.4.1.14823.2.3.2.11.6	INTEGER	read-write	This value indicates the starting month for Daylight Savings Time.
IP enterpriseApSNTPPrimaryServer	1.3.6.1.4.1.14823.2.3.2.11.2	IpAddress	read-write	This value indicates the IP address of the primary SNTP server.
IP enterpriseApSNTPSecondaryServer	1.3.6.1.4.1.14823.2.3.2.11.3	IpAddress	read-write	This value indicates the IP address of the secondary SNTP server.
INT enterpriseApSNTPState	1.3.6.1.4.1.14823.2.3.2.11.1	INTEGER	read-write	This value indicates whether SNTP is enabled or not. At least one of the SNTP servers must have a valid IP address before SNTP can be enabled.
INT enterpriseApSNTPTimezone	1.3.6.1.4.1.14823.2.3.2.11.4	INTEGER	read-write	This value indicates which timezone to use.
enterpriseApSsh	1.3.6.1.4.1.14823.2.3.2.14.2
T/F enterpriseApSshServerEnabled	1.3.6.1.4.1.14823.2.3.2.14.2.1	TruthValue	read-write	This value indicates whether SSH server is enabled.
I32 enterpriseApSshServerPort	1.3.6.1.4.1.14823.2.3.2.14.2.2	Integer32	read-write	This value indicates SSH server's port number.
T/F enterpriseApSshTelnetServerEnabled	1.3.6.1.4.1.14823.2.3.2.14.2.3	TruthValue	read-write	This value indicates whether telnet server is enabled.
enterpriseApSTP	1.3.6.1.4.1.14823.2.3.2.25
I32 enterpriseApSTPBridgeForwardingDelay	1.3.6.1.4.1.14823.2.3.2.25.5	Integer32	read-write	This value indicates the STP forwarding delay for the radio interface.(unit: second)
I32 enterpriseApSTPBridgeMaxAge	1.3.6.1.4.1.14823.2.3.2.25.3	Integer32	read-write	This value indicates the STP bridge max age for the radio interface.(unit: second)
I32 enterpriseApSTPBridgePriority	1.3.6.1.4.1.14823.2.3.2.25.2	Integer32	read-write	This value indicates the STP bridge priority for the radio interface.
INT enterpriseApSTPBridgeStatus	1.3.6.1.4.1.14823.2.3.2.25.1	INTEGER	read-write	This value indicates the STP bridge status for the radio interface.
enterpriseApSTPEthernetInterface	1.3.6.1.4.1.14823.2.3.2.25.7
I32 enterpriseApSTPEthernetLinkPathCost	1.3.6.1.4.1.14823.2.3.2.25.7.1	Integer32	read-write	This value indicates link path cost for ethernet interface.
I32 enterpriseApSTPEthernetLinkPortPriority	1.3.6.1.4.1.14823.2.3.2.25.7.2	Integer32	read-write	This value indicates link port prirorty for ethernet interface.
I32 enterpriseApSTPHelloTime	1.3.6.1.4.1.14823.2.3.2.25.4	Integer32	read-write	This value indicates the STP hello time for the radio interface.(unit: second)
enterpriseApSTPNodeEntry	1.3.6.1.4.1.14823.2.3.2.25.6.1.1		not-accessible	An entry in a table, contain the link path cost and link port priroity information.
I32 enterpriseApSTPNodeIndex	1.3.6.1.4.1.14823.2.3.2.25.6.1.1.1	Integer32	not-accessible	Peer Index for the nodes on the radio interface.
I32 enterpriseApSTPNodeLinkPathCost	1.3.6.1.4.1.14823.2.3.2.25.6.1.1.2	Integer32	read-write	This value indicates the link path cost for the node on this radio interface.
I32 enterpriseApSTPNodeLinkPortPriority	1.3.6.1.4.1.14823.2.3.2.25.6.1.1.3	Integer32	read-write	This value indicates the link path cost for the node on this radio interface.
enterpriseApSTPNodeTable	1.3.6.1.4.1.14823.2.3.2.25.6.1		not-accessible	The table of STP link Path Cost and link port priority information for each nodes on radio interface.
enterpriseApSTPRadioInterface	1.3.6.1.4.1.14823.2.3.2.25.6
enterpriseApSys	1.3.6.1.4.1.14823.2.3.2.1
enterpriseApSyslog	1.3.6.1.4.1.14823.2.3.2.13
INT enterpriseApSyslogConsoleState	1.3.6.1.4.1.14823.2.3.2.13.2	INTEGER	read-write	This value indicates whether syslog console logging is enabled.
INT enterpriseApSyslogLevel	1.3.6.1.4.1.14823.2.3.2.13.3	INTEGER	read-write	This value indicates the syslog logging level.
enterpriseApSyslogServerEntry	1.3.6.1.4.1.14823.2.3.2.13.4.1		not-accessible	An entry in the table, containing information about configuration of one syslog server of the AP.
I32 enterpriseApSyslogServerIndex	1.3.6.1.4.1.14823.2.3.2.13.4.1.1	Integer32	not-accessible	Index of the Syslog Server
IP enterpriseApSyslogServerIPAddress	1.3.6.1.4.1.14823.2.3.2.13.4.1.3	IpAddress	read-write	This value indicates the IP address of the syslog server.
INT enterpriseApSyslogServerPort	1.3.6.1.4.1.14823.2.3.2.13.4.1.4	INTEGER	read-write	This value indicates the UDP Port used by the syslog server.
INT enterpriseApSyslogServerState	1.3.6.1.4.1.14823.2.3.2.13.4.1.2	INTEGER	read-write	This value indicates whether the syslog server is enabled.
enterpriseApSyslogServerTable	1.3.6.1.4.1.14823.2.3.2.13.4		not-accessible	Table of descriptive and status information about configuration of each syslog server.
INT enterpriseApSyslogState	1.3.6.1.4.1.14823.2.3.2.13.1	INTEGER	read-write	This value indicates whether syslog is enabled.
enterpriseAPVapRadio	1.3.6.1.4.1.14823.2.3.2.20
I32 enterpriseAPVapRadioAssocTimeoutInterval	1.3.6.1.4.1.14823.2.3.2.20.1.1.9	Integer32	read-write	This value indicates the Association Timeout interval for this radio interface.
I32 enterpriseAPVapRadioAuthTimeoutInterval	1.3.6.1.4.1.14823.2.3.2.20.1.1.8	Integer32	read-write	This value indicates the Authentication Timeout interval for this radio interface.
INT enterpriseAPVapRadioClosedSystem	1.3.6.1.4.1.14823.2.3.2.20.1.1.3	INTEGER	read-write	This value indicates whether closed system is enabled for this radio interface.
STR enterpriseAPVapRadioDescription	1.3.6.1.4.1.14823.2.3.2.20.1.1.6	DisplayString	read-write	This value indicates the description for this radio interface.
enterpriseAPVapRadioEntry	1.3.6.1.4.1.14823.2.3.2.20.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 enterpriseAPVapRadioIndex	1.3.6.1.4.1.14823.2.3.2.20.1.1.1	Integer32	not-accessible	Radio Index for configuration.
INT enterpriseAPVapRadioMaxAssoc	1.3.6.1.4.1.14823.2.3.2.20.1.1.4	INTEGER	read-write	This value indicates the max number of clients allowed on this radio interface.
INT enterpriseAPVapRadioState	1.3.6.1.4.1.14823.2.3.2.20.1.1.2	INTEGER	read-write	This value indicates the state of the radio interface.
enterpriseAPVapRadioTable	1.3.6.1.4.1.14823.2.3.2.20.1		not-accessible	Table of descriptive and status information about configuration of each radio.
INT enterpriseAPVapRadioTransmitKey	1.3.6.1.4.1.14823.2.3.2.20.1.1.5	INTEGER	read-write	This value indicates default transmit key in use for this radio interface.
I32 enterpriseAPVapRadioWPA2PMKSALifeTime	1.3.6.1.4.1.14823.2.3.2.20.1.1.10	Integer32	read-write	This value indicates the WPA2 PMSA Life Time for this radio interface.
enterpriseApVLAN	1.3.6.1.4.1.14823.2.3.2.9
INT enterpriseApVLANNativeId	1.3.6.1.4.1.14823.2.3.2.9.1	INTEGER	read-write	This value indicates the native VLAN id.
INT enterpriseApVLANState	1.3.6.1.4.1.14823.2.3.2.9.2	INTEGER	read-write	This value indicates whether VLANs are enabled or disabled.
enterpriseApWMM	1.3.6.1.4.1.14823.2.3.2.24
INT enterpriseApWMMACKPolicy	1.3.6.1.4.1.14823.2.3.2.24.2.1.2	INTEGER	read-write	This value indicates WMM Ack Policy state of each ac number for the radio interface.
enterpriseApWMMAckPolicyEntry	1.3.6.1.4.1.14823.2.3.2.24.2.1		not-accessible	An entry of table, contains the WMM Ack Policy information.
I32 enterpriseApWMMAckPolicyIndex	1.3.6.1.4.1.14823.2.3.2.24.2.1.1	Integer32	read-only	The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effect) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)
enterpriseApWMMAckPolicyTable	1.3.6.1.4.1.14823.2.3.2.24.2		not-accessible	The table of WMM Ack Policy information for each ac number on the radio interface.
INT enterpriseApWMMAPParamAdmissionCtrl	1.3.6.1.4.1.14823.2.3.2.24.4.1.6	INTEGER	read-write	This value indicates the admission control of AP parameter for each AC number on the radio interface.
I32 enterpriseApWMMAPParamAIFSN	1.3.6.1.4.1.14823.2.3.2.24.4.1.4	Integer32	read-write	This value indicates the AIFSN of AP parameter for each AC number on the radio interface.
enterpriseApWMMAPParamEntry	1.3.6.1.4.1.14823.2.3.2.24.4.1		not-accessible	An entry table, include the Ap parameter information for each ac numbers.
I32 enterpriseApWMMAPParamIndex	1.3.6.1.4.1.14823.2.3.2.24.4.1.1	Integer32	read-only	The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effort) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)
I32 enterpriseApWMMAPParamLogCwMax	1.3.6.1.4.1.14823.2.3.2.24.4.1.3	Integer32	read-write	This value indicates the LogCwMax of AP parameter for each AC number on the radio interface.
I32 enterpriseApWMMAPParamLogCwMin	1.3.6.1.4.1.14823.2.3.2.24.4.1.2	Integer32	read-write	This value indicates the LogCwMin of AP parameter for each AC number on the radio interface.
enterpriseApWMMAPParamTable	1.3.6.1.4.1.14823.2.3.2.24.4		not-accessible	The table of configuration information for WMM AP parameters for each ac number on the radio interface.
I32 enterpriseApWMMAPParamTXOPLimit	1.3.6.1.4.1.14823.2.3.2.24.4.1.5	Integer32	read-write	This value indicates the TXOP Limit of AP parameter for each AC number on the radio interface.
INT enterpriseApWMMBSSParamAdmissionCtrl	1.3.6.1.4.1.14823.2.3.2.24.3.1.6	INTEGER	read-write	This value indicates the BSS parameters Admission Control of each AC number for the radio interface.
I32 enterpriseApWMMBSSParamAIFSN	1.3.6.1.4.1.14823.2.3.2.24.3.1.4	Integer32	read-write	This value indicates the WMM BSS parameters AIFSN of each AC number for the radio interface.
enterpriseApWMMBSSParamEntry	1.3.6.1.4.1.14823.2.3.2.24.3.1		not-accessible	An entry of table, contains the WMM BSS parameter information for each ac number on the radio interface.
I32 enterpriseApWMMBSSParamIndex	1.3.6.1.4.1.14823.2.3.2.24.3.1.1	Integer32	read-only	The value indicates the AC number for each radio interface. 0 --> AC0 (Best Effort) 1 --> AC1 (Background) 2 --> AC2 (Video) 3 --> AC3 (Voice)
I32 enterpriseApWMMBSSParamLogCwMax	1.3.6.1.4.1.14823.2.3.2.24.3.1.3	Integer32	read-write	This value indicates the WMM BSS parameter logCwMax of each AC number for the radio interface.
I32 enterpriseApWMMBSSParamLogCwMin	1.3.6.1.4.1.14823.2.3.2.24.3.1.2	Integer32	read-write	This value indicates the WMM BSS parameter logCwMin of AC number for the radio interface.
enterpriseApWMMBSSParamTable	1.3.6.1.4.1.14823.2.3.2.24.3		not-accessible	The table of WMM BSS parameter information.
I32 enterpriseApWMMBSSParamTXOPLimit	1.3.6.1.4.1.14823.2.3.2.24.3.1.5	Integer32	read-write	This value indicates the WMM BSS parameters TXOP Limit of each AC number for the radio interface.
enterpriseApWMMEntry	1.3.6.1.4.1.14823.2.3.2.24.1.1		not-accessible	An entry of table, contains the WMM information.
INT enterpriseApWMMMode	1.3.6.1.4.1.14823.2.3.2.24.1.1.2	INTEGER	read-write	This value indicates the WMM mode for the radio interface. disabled(1) To set WMM mode disabled. support (2) To set WMM mode supported. required(3) To set WMM mode required.
I32 enterpriseApWMMModeIndex	1.3.6.1.4.1.14823.2.3.2.24.1.1.1	Integer32	not-accessible	Peer Index for the radio interface.
enterpriseApWMMTable	1.3.6.1.4.1.14823.2.3.2.24.1		not-accessible	The table of WMM information for each radio interface.
IP fileServer	1.3.6.1.4.1.14823.2.3.2.4.5	IpAddress	read-write	The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been specified.
INT fileType	1.3.6.1.4.1.14823.2.3.2.4.2	INTEGER	read-write	Type of file to transfer.
NTF iappContextDataSent	1.3.6.1.4.1.14823.2.3.2.7.4.2.17			The IAPP Context Data Sent notification shall be sent out whenever the context data for a station has been sent to the new AP with which the station has associated. The notification shall include the MAC address of the station and the IP address of the new AP.
INT iappContextDataSentTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.21	INTEGER	read-write	This value indicates whether the iappContextDataSent trap is enabled.
NTF iappStationRoamedFrom	1.3.6.1.4.1.14823.2.3.2.7.4.2.15			The IAPP Station Roamed-From Notification shall be sent out whenever a station roams from another Access Point (AP) to this AP. The notification shall include the MAC address of the station and the IP address of the old AP.
INT iappStationRoamedFromTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.19	INTEGER	read-write	This value indicates whether the iappStationRoamedFrom trap is enabled.
NTF iappStationRoamedTo	1.3.6.1.4.1.14823.2.3.2.7.4.2.16			The IAPP Station Roamed-To Notification shall be sent out whenever a station roams to another Access Point (AP) from this AP. The notification shall include the MAC address of the station and the IP address of the new AP.
INT iappStationRoamedToTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.20	INTEGER	read-write	This value indicates whether the iappStationRoamedTo trap is enabled.
I32 lineDataBits	1.3.6.1.4.1.14823.2.3.2.2.1.1.2	Integer32	read-only	This is defined as number of data bits for the RS232 interface.
lineEntry	1.3.6.1.4.1.14823.2.3.2.2.1.1		not-accessible	An entry in the table, containing information about configuration in one RS232 line of the Access Point.
I32 lineIndex	1.3.6.1.4.1.14823.2.3.2.2.1.1.1	Integer32	not-accessible	This is defined as RS-232 index.
INT lineParity	1.3.6.1.4.1.14823.2.3.2.2.1.1.3	INTEGER	read-only	This is defined as parity of the RS232 interface.
I32 lineSpeed	1.3.6.1.4.1.14823.2.3.2.2.1.1.4	Integer32	read-only	This is defined as the speed of the RS-232 interface.
I32 lineStopBits	1.3.6.1.4.1.14823.2.3.2.2.1.1.5	Integer32	read-only	This is defined as the number of stop bits for the RS-232 interface.
lineTable	1.3.6.1.4.1.14823.2.3.2.2.1		not-accessible	Table of descriptive and status information about configuration of each RS-232 line in this system
NTF localMacAddrAuthFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.13			The Local MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
INT localMacAddrAuthFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.17	INTEGER	read-write	This value indicates whether the localMacAddrAuthFail trap is enabled.
NTF localMacAddrAuthSuccess	1.3.6.1.4.1.14823.2.3.2.7.4.2.12			The Local MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
INT localMacAddrAuthSuccessTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.16	INTEGER	read-write	This value indicates whether the localMacAddrAuthSuccess trap is enabled.
I32 nativeVlanIfIndex	1.3.6.1.4.1.14823.2.3.2.9.3.1.1	Integer32	not-accessible	Interface Index of the wireless interface for which the vlan is assigned to.
I32 nativeVlanSsidNumber	1.3.6.1.4.1.14823.2.3.2.9.3.1.2	Integer32	not-accessible	Associated Number for Service Set Id (SSID) of the wireless interface for which the vlan is assigned to. Note: This is for future support of multiple SSIDs per radio interface.
I32 nativeVlanVlanId	1.3.6.1.4.1.14823.2.3.2.9.3.1.3	Integer32	read-write	This value indicates the native VLAN id of the wireless interface associated with the if index and the SSID number(if it is not 0).
IP netConfigDefaultGateway	1.3.6.1.4.1.14823.2.3.2.6.3	IpAddress	read-write	The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
INT netConfigDHCPState	1.3.6.1.4.1.14823.2.3.2.6.8	INTEGER	read-write	Whether DHCP is enabled.
INT netConfigHttpPort	1.3.6.1.4.1.14823.2.3.2.6.5	INTEGER	read-write	The port number for HTTP. Default port number is 80.
INT netConfigHttpsPort	1.3.6.1.4.1.14823.2.3.2.6.7	INTEGER	read-write	The port number for Secure HTTP. Default port number is 443.
INT netConfigHttpsState	1.3.6.1.4.1.14823.2.3.2.6.6	INTEGER	read-write	Whether Secure HTTP is enabled.
INT netConfigHttpState	1.3.6.1.4.1.14823.2.3.2.6.4	INTEGER	read-write	Whether HTTP is enabled.
IP netConfigIPAddress	1.3.6.1.4.1.14823.2.3.2.6.1	IpAddress	read-write	The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
IP netConfigSubnetMask	1.3.6.1.4.1.14823.2.3.2.6.2	IpAddress	read-write	The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
STR password	1.3.6.1.4.1.14823.2.3.2.4.7	DisplayString	read-write	The password specified for an FTP Transfer.
INT portAutonegotiation	1.3.6.1.4.1.14823.2.3.2.3.1.1.7	INTEGER	read-only	Whether autonegotiation is enabled.
INT portCapabilities	1.3.6.1.4.1.14823.2.3.2.3.1.1.6	INTEGER	read-only	Port capabilities.
portEntry	1.3.6.1.4.1.14823.2.3.2.3.1.1		not-accessible	An entry in the table, containing information about configuration in one switch port of the switch.
INT portFlowCtrlCfg	1.3.6.1.4.1.14823.2.3.2.3.1.1.5	INTEGER	read-only	(1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (3) Flow control mechanism is backPressure. when the port is in fullDuplex mode.This flow control mechanism will not function. (4) Flow control mechanism is IEEE 802.3x flow control. when the port is in halfDuplex mode.This flow control mechanism will not function. hundredBaseTX and thousandBaseSX port can be set as: enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4). hundredBaseFX port can be set as: enabled(1), disabled(2), backPressure(3). The actual flow control mechanism is used given by portFlowCtrlStatus.
INT portFlowCtrlStatus	1.3.6.1.4.1.14823.2.3.2.3.1.1.9	INTEGER	read-only	(2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
I32 portIndex	1.3.6.1.4.1.14823.2.3.2.3.1.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
STR portName	1.3.6.1.4.1.14823.2.3.2.3.1.1.2	DisplayString	read-only	Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).
INT portSpeedDpxCfg	1.3.6.1.4.1.14823.2.3.2.3.1.1.4	INTEGER	read-only	Indicates the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
INT portSpeedDpxStatus	1.3.6.1.4.1.14823.2.3.2.3.1.1.8	INTEGER	read-only	The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
portTable	1.3.6.1.4.1.14823.2.3.2.3.1		not-accessible	Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains information about each trunk (similar to Cisco's EtherChannel).
INT portType	1.3.6.1.4.1.14823.2.3.2.3.1.1.3	INTEGER	read-only	Indicates the port type.
INT possibleRogueAPDetectedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.28	INTEGER	read-write	This value indicates whether the RogueAPDetectedTrapEnabled trap is enabled.
NTF pppLogonFail	1.3.6.1.4.1.14823.2.3.2.7.4.2.14			The PPP Logon failure notification shall be sent out when the AP fails to login successfully to the PPP peer using the supplied username and password.
INT pppLogonFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.18	INTEGER	read-write	This value indicates whether the pppLogonFail trap is enabled.
INT restartControl	1.3.6.1.4.1.14823.2.3.2.5.2	INTEGER	read-write	Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
STR restartOpCodeFile	1.3.6.1.4.1.14823.2.3.2.5.1	DisplayString	read-write	Name of op-code file for start-up.
INT rogueAPDetectedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.27	INTEGER	read-write	This value indicates whether the RogueAPDetectedTrapEnabled trap is enabled.
sntpNotificationObjects	1.3.6.1.4.1.14823.2.3.2.11.10.1
sntpNotifications	1.3.6.1.4.1.14823.2.3.2.11.10.2
sntpNotificationTree	1.3.6.1.4.1.14823.2.3.2.11.10
NTF sntpServerFail	1.3.6.1.4.1.14823.2.3.2.11.10.2.1			The sntpServerFail notification shall be sent when the AP fails to get time from the configured SNTP server.
INT sntpServerFailTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.22	INTEGER	read-write	This value indicates whether the sntpServerFail trap is enabled.
STR srcFile	1.3.6.1.4.1.14823.2.3.2.4.3	DisplayString	read-write	The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
INT status	1.3.6.1.4.1.14823.2.3.2.4.8	INTEGER	read-only	The status of the transfer.
STR swBootRomVer	1.3.6.1.4.1.14823.2.3.2.1.2	DisplayString	read-only	Boot ROM code version of the main board.
STR swHardwareVer	1.3.6.1.4.1.14823.2.3.2.1.1	DisplayString	read-only	Hardware version of the main board.
STR swOpCodeVer	1.3.6.1.4.1.14823.2.3.2.1.3	DisplayString	read-only	Operation code version of the main board.
STR swSerialNumber	1.3.6.1.4.1.14823.2.3.2.1.4	DisplayString	read-only	Serial Number of the Access Point.
NTF sysConfigFileVersionChanged	1.3.6.1.4.1.14823.2.3.2.1.5.2.4			The Config file version changed notification shall be sent when the version of the AP's configuration file has changed.
INT sysConfigFileVersionChangedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.4	INTEGER	read-write	This value indicates whether the sysConfigFileVersionChanged trap is enabled.
sysNotificationObjects	1.3.6.1.4.1.14823.2.3.2.1.5.1
sysNotifications	1.3.6.1.4.1.14823.2.3.2.1.5.2
sysNotificationTree	1.3.6.1.4.1.14823.2.3.2.1.5
NTF sysRadiusServerChanged	1.3.6.1.4.1.14823.2.3.2.1.5.2.3			The RADIUS server changed notification shall be sent when the RADIUS server has changed from Primary / Secondary to Secondary / Primary.
INT sysRadiusServerChangedTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.3	INTEGER	read-write	This value indicates whether the sysRadiusServerChanged trap is enabled.
NTF sysSystemDown	1.3.6.1.4.1.14823.2.3.2.1.5.2.2			The system down notification shall be sent before the AP is about to reboot.
INT sysSystemDownTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.2	INTEGER	read-write	This value indicates whether the sysSystemDowntrap is enabled.
NTF sysSystemUp	1.3.6.1.4.1.14823.2.3.2.1.5.2.1			The system up notification shall be sent when the AP is fully up and running.
INT sysSystemUpTrapEnabled	1.3.6.1.4.1.14823.2.3.2.16.4.1	INTEGER	read-write	This value indicates whether the sysSystemUp trap is enabled.
INT transferStart	1.3.6.1.4.1.14823.2.3.2.4.9	INTEGER	read-write	Set to go(1) to start a transfer.
INT transferType	1.3.6.1.4.1.14823.2.3.2.4.1	INTEGER	read-write	Type of file to transfer.
MAC uplinkPortMACAddr	1.3.6.1.4.1.14823.2.3.2.10.5.3.1.2	MacAddress	read-only	The MAC Address of wireless clients which allowed to communicate on subnet.
MAC uplinkPortMACAddrFilterAddMac	1.3.6.1.4.1.14823.2.3.2.10.5.2	MacAddress	read-write	To add mac address to Uplink Port MAC Address Filter Table. (Mac Address format: xx-xx-xx-xx-xx-xx or xx:xx:xx:xx:xx:xx)
uplinkPortMACAddrFilteringEntry	1.3.6.1.4.1.14823.2.3.2.10.5.3.1		not-accessible	An entry in Uplink Port MAC Address Filter Table.
uplinkPortMACAddrFilteringTable	1.3.6.1.4.1.14823.2.3.2.10.5.3		not-accessible	Table of descriptive and status information about configuration of the Uplink Port MAC Address Filter Table.
INT uplinkPortMACAddrFilterStatus	1.3.6.1.4.1.14823.2.3.2.10.5.1	INTEGER	read-write	This value indicates whether the Uplink Port MAC Address Filter Table is enabled or not.
I32 uplinkPortMacAddrIndex	1.3.6.1.4.1.14823.2.3.2.10.5.3.1.1	Integer32	read-only	The index for Uplink Port MAC Address Filter Table.
STR userName	1.3.6.1.4.1.14823.2.3.2.4.6	DisplayString	read-write	The username specified for an FTP Transfer.
INT wdsApRole	1.3.6.1.4.1.14823.2.3.2.22.1.1.1	INTEGER	read-write	This value indicates the role of the Ap for this radio, roleAp(1): AP operation. roleBridgeMaster(2): Root-Bridge mode. roleBridge(4): Bridge Mode. relay wireless traffic.
INT wdsChannelAutoSync	1.3.6.1.4.1.14823.2.3.2.22.1.1.3	INTEGER	read-write	This value indicates the states of channel auto synchronize for this radio.
INT wdsMasterSlaveMode	1.3.6.1.4.1.14823.2.3.2.22.1.1.4	INTEGER	read-write	This value indicates the Master/Slave mode for this radio. master (1) To set to master mode. slave (2) To set to slave mode.
STR wdsPeerBssid	1.3.6.1.4.1.14823.2.3.2.22.2.1.2	DisplayString	read-write	The BSSID for this peer.
I32 wdsPeerIndex	1.3.6.1.4.1.14823.2.3.2.22.2.1.1	Integer32	not-accessible	Peer Index for the radio interface.
wlsrOutDoorApMibModules	1.3.6.1.4.1.14823.2.3.2

RFC description

Aruba outdoor access point system, radio, network, and security management.

Start monitoring Aruba Networks (HPE) outdoor wireless access points (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AP80-PRIVATE-MIB

What Is AP80-PRIVATE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description