ALPINE-GEN-CARD-EDFA-MIB

All MIBs › ALPINE-GEN-CARD-EDFA-MIB

Category: Optical and WDM

Description: Alpine Photonics/JDSU generic EDFA card MIB for managing erbium-doped fiber amplifier gain, power, and alarm parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALPINE-GEN-CARD-EDFA-MIB?

ALPINE-GEN-CARD-EDFA-MIB is a vendor-specific MIB associated with Alpine Photonics/JDSU-lineage optical equipment, intended for managing generic EDFA (Erbium-Doped Fiber Amplifier) cards used in optical/DWDM transmission systems. No module description or sample objects were provided for this entry, so specific object names cannot be confirmed, but based on its name and category it would be expected to expose configuration and status data for the amplifier card, such as pump laser status, input/output optical power, gain settings, and alarm conditions. Its likely primary monitoring value is hardware health of the optical amplifier card - laser bias current, optical power levels, and alarm/fault status are the kinds of things such an EDFA card MIB would expose, though this cannot be verified from the available data. As an optical transport card MIB it likely depends on a parent chassis/shelf MIB for slot and card identification context. It would typically be deployed in DWDM/optical transport network elements using EDFA amplifier cards for long-haul or metro fiber links, and an ALPINE-GEN-CARD-EDFA-MIB download would be needed from the vendor to load the module into a MIB browser for verification.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALPINE-GEN-CARD-EDFA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alpine Photonics/JDSU EDFA optical amplifier cards (DWDM/optical transport equipment)

Monitoring Examples

No sample objects were provided for this MIB, so specific table or object names cannot be confirmed, and inventing a monitoring scenario would not be grounded in the actual MIB content. Typically an EDFA card MIB of this type would expose per-card output power, pump laser current, and alarm status for detecting amplifier degradation or laser end-of-life, but these specifics are not verifiable from the given data.

Imported Objects

From ALPINE-ROOT

alpineGeneric

OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
NOTIFICATION-TYPE
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
alpineGenCardEdfa	1.3.6.1.4.1.52326.1.1
alpineGenCardEdfaInfosTable	1.3.6.1.4.1.52326.1.1.1		not-accessible	Description.
alpineGenCardEdfaInfosEntry	1.3.6.1.4.1.52326.1.1.1.1		not-accessible	Description.
I32 gceSlotNum	1.3.6.1.4.1.52326.1.1.1.1.1	Integer32	read-only	Slot number.
I32 gceEdfaNum	1.3.6.1.4.1.52326.1.1.1.1.2	Integer32	read-only	EDFA Number in the line card. Up to 2 EDFA modules are supported in one line card.
I32 gceMode	1.3.6.1.4.1.52326.1.1.1.1.3	Integer32	read-write	Work mode of EDFA. 1. AGC 2. APC Please note, when you want to change work mode, make sure the relative target value be set first. For example, if you want to set work mode to APC and the output power is 5dBm, you need set 'gceOutputPowerTarget' to 5 first.
OCT gceOutputPowerTarget	1.3.6.1.4.1.52326.1.1.1.1.4	OCTET STRING	read-write	Output power target of EDFA. If current work mode is APC, then output power will be applied immediately. If current work mode is AGC, then output power will be applied after 'gceMode' is set to APC.
OCT gceGainTarget	1.3.6.1.4.1.52326.1.1.1.1.5	OCTET STRING	read-write	Gain target of EDFA. If current work mode is AGC, then output power will be applied immediately. If current work mode is APC, then output power will be applied after 'gceMode' is set to AGC.
OCT gceOutputPower	1.3.6.1.4.1.52326.1.1.1.1.6	OCTET STRING	read-only	Current output power of EDFA.
OCT gceGain	1.3.6.1.4.1.52326.1.1.1.1.7	OCTET STRING	read-only	Current gain of EDFA.
OCT gceTemperature	1.3.6.1.4.1.52326.1.1.1.1.8	OCTET STRING	read-only	Current temperature of EDFA.
I32 gceSaveConfig	1.3.6.1.4.1.52326.1.1.1.1.9	Integer32	read-write	Save current configuration into flash for non-valatile setting. 0: Idle/Save Done. 1: Issue save command. 2: Saving. Only value 1 can be accepted in snmp set.
OCT gceInputPower	1.3.6.1.4.1.52326.1.1.1.1.10	OCTET STRING	read-only	Current input power of EDFA.
alpineGenCardEdfaAlarm	1.3.6.1.4.1.52326.1.1.2
alpineGenCardEdfaAlarmThldTable	1.3.6.1.4.1.52326.1.1.2.1		not-accessible	Description.
alpineGenCardEdfaAlarmThldEntry	1.3.6.1.4.1.52326.1.1.2.1.1		not-accessible	Description.
I32 gceaSlotNum	1.3.6.1.4.1.52326.1.1.2.1.1.1	Integer32	read-only	Slot number.
I32 gceaEdfaNum	1.3.6.1.4.1.52326.1.1.2.1.1.2	Integer32	read-only	EDFA Number in the line card. Up to 2 EDFA modules are supported in one line card.
OCT gceaInputPowerThld	1.3.6.1.4.1.52326.1.1.2.1.1.3	OCTET STRING	read-write	Low threshold of input power.
OCT gceaOutputPowerThld	1.3.6.1.4.1.52326.1.1.2.1.1.4	OCTET STRING	read-write	Low threshold of output power.
OCT gceaTemperatureThld	1.3.6.1.4.1.52326.1.1.2.1.1.5	OCTET STRING	read-write	High threshold of temperature.
alpineGenEdfaAlarmInfoTable	1.3.6.1.4.1.52326.1.1.2.2		not-accessible	Description.
alpineGenEdfaAlarmInfoEntry	1.3.6.1.4.1.52326.1.1.2.2.1		not-accessible	Description.
I32 geaiSlotNum	1.3.6.1.4.1.52326.1.1.2.2.1.1	Integer32	read-only	Description.
I32 geaiEdfaNum	1.3.6.1.4.1.52326.1.1.2.2.1.2	Integer32	read-only	EDFA Number in the line card. Up to 2 EDFA modules are supported in one line card.
I32 geaiCommonAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.3	Integer32	read-only	If any alarm occurs, this field will set to 1. 0. Normal 1. One or some alarm occur.
I32 geaiCaseTemperatureAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.4	Integer32	read-only	0. Clear 1. Case temperature alarm occurs.
I32 geaiPumpTemperatureAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.5	Integer32	read-only	0. Clear 1. Pump temperature alarm occurs.
I32 geaiPumpBiasAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.6	Integer32	read-only	0. Clear 1. Pump bias alarm occurs.
I32 geaiLossInputAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.7	Integer32	read-only	0. Clear 1. Loss of input alarm occurs.
I32 geaiLossOutputAlarm	1.3.6.1.4.1.52326.1.1.2.2.1.8	Integer32	read-only	0. Clear 1. Loss of output alarm occurs.
NTF alpineGenEdfaPowerAlarm	1.3.6.1.4.1.52326.1.1.2.3			Description.
NTF alpineGenEdfaTemperatureAlarm	1.3.6.1.4.1.52326.1.1.2.4			Description.
NTF alpineGenEdfaBiasAlarm	1.3.6.1.4.1.52326.1.1.2.5			Description.
NTF alpineGenEdfaLossAlarm	1.3.6.1.4.1.52326.1.1.2.6			Description.

RFC description

EDFA card information for Alpine generic cards.

Start monitoring Alpine Photonics (JDSU/Viavi) EDFA optical amplifier cards (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALPINE-GEN-CARD-EDFA-MIB

What Is ALPINE-GEN-CARD-EDFA-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description