ADTRAN-ATLAS-V35NX-MIB

All MIBs › ADTRAN-ATLAS-V35NX-MIB

Category: Vendor: ADTRAN

Description: Manages V.35 NxDS0 inverse multiplexer interfaces on ADTRAN ATLAS multiservice access devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ADTRAN-ATLAS-V35NX-MIB?

ADTRAN-ATLAS-V35NX-MIB is a private enterprise MIB from ADTRAN covering V.35 NxDS0 (inverse-multiplexed) WAN interface modules installed in ADTRAN ATLAS multiservice access platforms. It exposes a per-slot/per-port interface table describing each V.35 NxDS0 circuit's configuration (data rate) and operational status. Critically for hardware/software health monitoring it reports adATLASV35NxIfAlarmStatus, adATLASV35NxIfDTEStatus, and adATLASV35NxIfPLLFifoStatus, letting an operator see line alarms, DTE (attached equipment) link state, and clock-synchronization (PLL/FIFO) health for each circuit, plus an inband statistics table for further diagnostics. It builds on the standard IF-MIB interface indexing conventions common to ADTRAN's chassis-based product MIBs. It is deployed on ADTRAN ATLAS multiservice access devices used to aggregate multiple DS0 channels into higher-bandwidth V.35 serial WAN links. Network engineers evaluating or troubleshooting this functionality can download the ADTRAN-ATLAS-V35NX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ADTRAN-ATLAS-V35NX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADTRAN ATLAS multiservice access devices
V.35 NxDS0 inverse-multiplexer interface modules

Monitoring Examples

An admin would walk adATLASV35NxIfTable/adATLASV35NxIfEntry (indexed by adATLASV35NxIfSlotNum and adATLASV35NxIfPortNum) and check adATLASV35NxIfAlarmStatus and adATLASV35NxIfDTEStatus per port to detect a WAN circuit failure or an attached DTE device going offline. A degraded adATLASV35NxIfPLLFifoStatus reading would indicate clock slips/jitter on the inverse-multiplexed bundle, while adATLASV35NxIfInbandStatTable provides finer-grained inband error statistics. adATLASV35NxIfDataRate confirms the currently negotiated aggregate bandwidth for the NxDS0 group.

What Can Be Monitored

V.35 NxDS0 interface alarm status
DTE link status
PLL/FIFO clock synchronization status
negotiated data rate
inband circuit statistics

Imported Objects

From ADTRAN-ATLAS-MODULE-MIB

adATLASModuleInfoFPStatus

OBJECT-TYPE

From ADTRAN-ATLAS-UNIT-MIB

adATLASUnitFPStatus	OBJECT-TYPE
adATLASUnitPortAddress	OBJECT-TYPE
adATLASUnitSlotAddress	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
enterprises

From RFC1213-MIB

ifIndex

OIDs

OID symbolic	OID numeric	Type	Access	Description
adtran	1.3.6.1.4.1.664
adMgmt	1.3.6.1.4.1.664.2
adATLASmg	1.3.6.1.4.1.664.2.154
NTF adATLASV35NxSlipAlarmActive	1.3.6.1.4.1.664.2.154.0.15400700			This trap indicates a SLIP alarm is active.
NTF adATLASV35NxSlipAlarmInActive	1.3.6.1.4.1.664.2.154.0.15400701			This trap indicates a SLIP alarm is inactive.
NTF adATLASV35NxPLLAlarmActive	1.3.6.1.4.1.664.2.154.0.15400702			This trap indicates a PLL alarm is active.
NTF adATLASV35NxPLLAlarmInActive	1.3.6.1.4.1.664.2.154.0.15400703			This trap indicates a PLL alarm is inactive.
NTF adATLASV35NxZeroAlarmActive	1.3.6.1.4.1.664.2.154.0.15400704			This trap indicates a Zero alarm is active.
NTF adATLASV35NxZeroAlarmInActive	1.3.6.1.4.1.664.2.154.0.15400705			This trap indicates a Zero alarm is inactive.
NTF adATLASV35NxExtClkAlarmActive	1.3.6.1.4.1.664.2.154.0.15400706			This trap indicates a no external clock alarm is active.
NTF adATLASV35NxExtClkAlarmInActive	1.3.6.1.4.1.664.2.154.0.15400707			This trap indicates a no external clock alarm is inactive.
NTF adATLASV35NxRTSActive	1.3.6.1.4.1.664.2.154.0.15400708			This trap indicates the RTS Lead is active.
NTF adATLASV35NxRTSInActive	1.3.6.1.4.1.664.2.154.0.15400709			This trap indicates the RTS Lead is inactive.
NTF adATLASV35NxCTSActive	1.3.6.1.4.1.664.2.154.0.15400710			This trap indicates the CTS Lead is active.
NTF adATLASV35NxCTSInActive	1.3.6.1.4.1.664.2.154.0.15400711			This trap indicates the CTS Lead is inactive.
NTF adATLASV35NxDTRActive	1.3.6.1.4.1.664.2.154.0.15400712			This trap indicates the DTR Lead is active.
NTF adATLASV35NxDTRInActive	1.3.6.1.4.1.664.2.154.0.15400713			This trap indicates the DTR Lead is inactive.
NTF adATLASV35NxDSRActive	1.3.6.1.4.1.664.2.154.0.15400714			This trap indicates the DSR Lead is active.
NTF adATLASV35NxDSRInActive	1.3.6.1.4.1.664.2.154.0.15400715			This trap indicates the DSR Lead is inactive.
NTF adATLASV35NxDCDActive	1.3.6.1.4.1.664.2.154.0.15400716			This trap indicates the DCD Lead is active.
NTF adATLASV35NxDCDInActive	1.3.6.1.4.1.664.2.154.0.15400717			This trap indicates the DCD Lead is inactive.
NTF adATLASV35NxRIActive	1.3.6.1.4.1.664.2.154.0.15400718			This trap indicates the RI Lead is active.
NTF adATLASV35NxRIInActive	1.3.6.1.4.1.664.2.154.0.15400719			This trap indicates the RI Lead is inactive.
NTF adATLASV35NxTDActive	1.3.6.1.4.1.664.2.154.0.15400720			This trap indicates the presence of transistions on the TD lead.
NTF adATLASV35NxTDInActive	1.3.6.1.4.1.664.2.154.0.15400721			This trap indicates the absence of transistions on the TD lead.
NTF adATLASV35NxRDActive	1.3.6.1.4.1.664.2.154.0.15400722			This trap indicates the presence of transistions on the RD Lead.
NTF adATLASV35NxRDInActive	1.3.6.1.4.1.664.2.154.0.15400723			This trap indicates the absence of transistions on the RD Lead.
NTF adATLASV35NxECActive	1.3.6.1.4.1.664.2.154.0.15400724			This trap indicates the presence of transistions on the EC Lead.
NTF adATLASV35NxECInActive	1.3.6.1.4.1.664.2.154.0.15400725			This trap indicates the absence of transistions on the EC Lead.
adGenATLASmg	1.3.6.1.4.1.664.2.154.1
adATLASV35Nxmg	1.3.6.1.4.1.664.2.154.1.7
INT adATLASV35NxIfNumber	1.3.6.1.4.1.664.2.154.1.7.1	INTEGER	read-only	The number of V.35 Nx ports (regardless of their current state) present on this system.
adATLASV35NxIfTable	1.3.6.1.4.1.664.2.154.1.7.2		not-accessible	The ATLAS V.35 Nx Interface Status Table.
adATLASV35NxIfEntry	1.3.6.1.4.1.664.2.154.1.7.2.1		not-accessible	An entry in the ATLAS V.35 Nx Interface Status Table.
INT adATLASV35NxIfIndex	1.3.6.1.4.1.664.2.154.1.7.2.1.1	INTEGER	read-only	This variable indicates the interface number of a particular V.35 Nx port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
INT adATLASV35NxIfSlotNum	1.3.6.1.4.1.664.2.154.1.7.2.1.2	INTEGER	read-only	This variable indicates the slot number of a particular ATLAS module with a V.35 Nx interface.
INT adATLASV35NxIfPortNum	1.3.6.1.4.1.664.2.154.1.7.2.1.3	INTEGER	read-only	This variable indicates the port number of a particular V.35 Nx interface on an ATLAS module.
INT adATLASV35NxIfAlarmStatus	1.3.6.1.4.1.664.2.154.1.7.2.1.4	INTEGER	read-only	This bit-encoded variable indicates the current alarm status of a V.35 Nx interface. This variable is encoded as follows: CLOCK SLIP ALARM 0x01 PLL ALARM 0x02 ZERO ALARM 0x04 NO EXT CLK ALARM 0x08 Note: There may be multiple bits set based on the current state of the interface. If a bit is set, then the corresponding alarm is active.
INT adATLASV35NxIfDTEStatus	1.3.6.1.4.1.664.2.154.1.7.2.1.5	INTEGER	read-only	This bit-encoded variable indicates the current state of the DTE leads on a V.35 Nx interface. This variable is encoded as follows: RTS 0x001 CTS 0x002 DTR 0x004 DSR 0x008 DCD 0x010 RI 0x020 TD 0x040 RD 0x080 EC 0x100 Note: There may be multiple bits set based on the current state of the interface. If a bit is set, then the corresponding DTE lead is active.
GAU adATLASV35NxIfDataRate	1.3.6.1.4.1.664.2.154.1.7.2.1.6	Gauge	read-only	This variable indicates the current data rate of a V.35 Nx interface.
INT adATLASV35NxIfPLLFifoStatus	1.3.6.1.4.1.664.2.154.1.7.2.1.7	INTEGER	read-only	This bit-encoded variable indicates the current PLL/FIFO status of a V.35 Nx interface. This variable is encoded as follows: LOCK 0x01 RXE 0x02 RXF 0x04 TXE 0x08 TXF 0x10 Note: There may be multiple bits set based on the current state of the interface.
adATLASV35NxIfInbandStatTable	1.3.6.1.4.1.664.2.154.1.7.3		not-accessible	The ATLAS V.35 Nx Interface Inband Statistics Table.
adATLASV35NxIfInbandStatEntry	1.3.6.1.4.1.664.2.154.1.7.3.1		not-accessible	An entry in the ATLAS V.35 Nx Interface Inband Statistics Table.
INT adATLASV35NxIfInbandStatIndex	1.3.6.1.4.1.664.2.154.1.7.3.1.1	INTEGER	read-only	This variable indicates the Interface number of a particular V.35 Nx port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
CTR adATLASV35NxIfInbandStatRxFrames	1.3.6.1.4.1.664.2.154.1.7.3.1.2	Counter	read-only	This variable indicates the number of frames recieved by a particular V.35 Nx interface.
CTR adATLASV35NxIfInbandStatTxFrames	1.3.6.1.4.1.664.2.154.1.7.3.1.3	Counter	read-only	This variable indicates the number of frames transmitted by a particular V.35 Nx interface.
CTR adATLASV35NxIfInbandStatRxBytes	1.3.6.1.4.1.664.2.154.1.7.3.1.4	Counter	read-only	This variable indicates the number of bytes recieved by a particular V.35 Nx interface.
CTR adATLASV35NxIfInbandStatTxBytes	1.3.6.1.4.1.664.2.154.1.7.3.1.5	Counter	read-only	This variable indicates the number of bytes transmitted by a particular V.35 Nx interface.
INT adATLASV35NxIfInbandStatReset	1.3.6.1.4.1.664.2.154.1.7.3.1.6	INTEGER	read-write	This variable is used to reset the inband statistics.
adATLASV35NxTstTable	1.3.6.1.4.1.664.2.154.1.7.4		not-accessible	The ATLAS V.35 Nx Interface Test Table.
adATLASV35NxTstEntry	1.3.6.1.4.1.664.2.154.1.7.4.1		not-accessible	An entry in the ATLAS V.35 Nx Interface Test Table.
INT adATLASV35NxTstIndex	1.3.6.1.4.1.664.2.154.1.7.4.1.1	INTEGER	read-only	This variable indicates the interface number of a particular V.35 Nx port within the ATLAS product. This number will be the same as the ifIndex located in the MIB-II interface table.
INT adATLASV35NxTstLoopbk	1.3.6.1.4.1.664.2.154.1.7.4.1.2	INTEGER	read-write	This variable controls the activation and deactivation of loopbacks on a particular V.35 Nx interface.
INT adATLASV35NxTstLoopbkStatus	1.3.6.1.4.1.664.2.154.1.7.4.1.3	INTEGER	read-only	This variable indicates a V.35 Nx interface�s current loopback status by displaying one of the following status messages: � No loopback active � Looping up remote unit � Remote unit looped back � Looping down remote unit � Remote loopup failed � Port looped from remote source � Port loopback active.
INT adATLASV35NxTst511Pattern	1.3.6.1.4.1.664.2.154.1.7.4.1.4	INTEGER	read-write	This variable controls the activation and deactivation of the 511 test pattern generator and detector.
INT adATLASV35NxTstPatternSync	1.3.6.1.4.1.664.2.154.1.7.4.1.5	INTEGER	read-only	This variable displays the synchronization status of the 511 pattern test.
INT adATLASV35NxTstPatternSyncLost	1.3.6.1.4.1.664.2.154.1.7.4.1.6	INTEGER	read-only	This variable displays whether or not the synchronization was ever lost during the 511 pattern test.
CTR adATLASV35NxTstPatternESs	1.3.6.1.4.1.664.2.154.1.7.4.1.7	Counter	read-only	This variable indicates the number of seconds (after pattern sync) of the 511 pettern test that have contained at least one error.
INT adATLASV35NxTstInjectErrs	1.3.6.1.4.1.664.2.154.1.7.4.1.8	INTEGER	read-write	Inject a 511 pattern error into the data stream.
INT adATLASV35NxTstClearRslts	1.3.6.1.4.1.664.2.154.1.7.4.1.9	INTEGER	read-write	Reset all test results.

RFC description

MIB module for monitoring ADTRAN ATLAS V.35 synchronous interface status, including alarms and data rates.

Start monitoring ADTRAN ATLAS-series multiservice access devices (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ADTRAN-ATLAS-V35NX-MIB

What Is ADTRAN-ATLAS-V35NX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description