A3COM-HUAWEI-VODIGITALIF-MIB

All MIBs › A3COM-HUAWEI-VODIGITALIF-MIB

Organization: Huawei-3COM Technologies Co., Ltd.

Last Updated: 2005-03-15

Category: Telephony and VoIP, Vendor: H3C/HH3C

Description: Manages digital voice interfaces (E1/T1 PRI/BRI ports) on H3C/3Com voice gateways, including D-channel protocol, timeslot configuration, and line status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-VODIGITALIF-MIB?

This is a joint 3Com/Huawei (H3C) private MIB covering digital voice interfaces such as E1/T1 PRI and BRI ports on H3C/3Com voice gateways, used to carry PSTN or PBX trunk traffic. It generally exposes configuration data for digital voice interface settings, including D-channel signaling protocol selection and timeslot allocation. Because it configures physical telephony ports, it also supports monitoring hardware status such as line/interface up-down state, letting administrators confirm a voice trunk card is operating correctly. The module description gives only a general purpose statement, so it likely relies on standard IF-MIB ifIndex conventions for interface identification, though this cannot be fully confirmed from the available data. It is deployed in enterprise or carrier voice-gateway environments where H3C/3Com equipment bridges TDM voice trunks to IP or PBX systems. Engineers can download the A3COM-HUAWEI-VODIGITALIF-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-VODIGITALIF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C/3Com voice gateway
PBX/TDM voice access device

Monitoring Examples

No sample object names were provided for this module, so specific table/object names cannot be cited from source data. A typical deployment would involve polling a digital-interface table indexed by port/timeslot to check D-channel protocol state and line status, with a down or alarmed interface indicating a physical trunk or framing problem, but this structure is inferred rather than confirmed.

What Can Be Monitored

D-channel signaling protocol state
timeslot configuration
PRI/BRI line status
voice interface admin/operational status

Imported Objects

From A3COM-HUAWEI-OID-MIB

h3cVoice

OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT h3cVoDIfCfgBoardType	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.3	INTEGER	read-only	This object indicates the type of board.
I32 h3cVoDIfCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfCfgPortSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.6	OCTET STRING	read-only	This object indicates the port subscriber line name.
INT h3cVoDIfCfgSignalType	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.4	INTEGER	read-only	This object indicates the signal type of a group.
OCT h3cVoDIfCfgTsInformation	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1.5	OCTET STRING	read-only	This object indicates the availability of every single timeslot for voice services. '1' indicates the timeslot is available for voice services. '0' indicates the timeslot is not available for voice services.
I32 h3cVoDIfEMABCDCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfEMABCDCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfEMABCDRxIdle	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.3	OCTET STRING	read-write	This object indicates the ABCD bits of receiving idle signal.
OCT h3cVoDIfEMABCDRxSeizure	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.4	OCTET STRING	read-write	This object indicates the ABCD bits of receiving seizure signal.
OCT h3cVoDIFEMABCDSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.7	OCTET STRING	read-only	This object indicates the port subscriber line name.
OCT h3cVoDIfEMABCDTxIdle	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.5	OCTET STRING	read-write	This object indicates the ABCD bits of sending idle signal.
OCT h3cVoDIfEMABCDTxSeizure	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1.6	OCTET STRING	read-write	This object indicates the ABCD bits of sending seizure signal.
I32 h3cVoDIfEMCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfEMCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfEMCfgPortSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.6	OCTET STRING	read-only	This object indicates the port subscriber line name.
I32 h3cVoDIfEMCfgTimeoutInterDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.3	Integer32	read-write	The maximum seconds, to wait for two DTMF (Dual Tone Multi-Frequency) number.
I32 h3cVoDIfEMCfgTimeoutRinging	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.4	Integer32	read-write	The maximum seconds, to wait for the ring back on the EM interface.
I32 h3cVoDIfEMCfgTimeoutWaitDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1.5	Integer32	read-write	The maximum seconds, to wait for called number of called side.
I32 h3cVoDIfEMTimerDelayHold	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.9	Integer32	read-write	This object indicates the maximum duration in milliseconds for sending delay signal. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emDelayStart'.
I32 h3cVoDIfEMTimerDelayRising	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.8	Integer32	read-write	This object indicates the maximum duration in milliseconds between receiveing seizure signal and sending delay signal. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emDelayStart'.
I32 h3cVoDIfEMTimerDialoutDelay	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.7	Integer32	read-write	This object indicates the maximum duration in milliseconds for sending called digits. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emImmediateStart'.
I32 h3cVoDIfEMTimerDtmf	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.10	Integer32	read-write	This object indicates DTMF sending duration in milliseconds.
I32 h3cVoDIfEMTimerDtmfInterval	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.11	Integer32	read-write	This object indicates DTMF sending interval in milliseconds.
I32 h3cVoDIfEMTimerGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfEMTimerPort	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfEMTimerPortSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.12	OCTET STRING	read-only	This object indicates the port subscriber line name.
I32 h3cVoDIfEMTimerSendWink	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.4	Integer32	read-write	This object indicates the maximum time in milliseconds between receiving seizure signal and sending wink signal. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emWinkStart'.
I32 h3cVoDIfEMTimerWinkHold	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.6	Integer32	read-write	This object indicates the maximum duration in milliseconds for sending wink signal. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emWinkStart'.
I32 h3cVoDIfEMTimerWinkRising	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1.5	Integer32	read-write	This object indicates the maximum time in milliseconds between sending seizure signal and receiving wink signal. This object can only take effect when h3cVoDIfCfgSignalType is set to 'emWinkStart'.
I32 h3cVoDIfR2ABCDCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfR2ABCDCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfR2ABCDRenewABCD	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.4	OCTET STRING	read-write	This object indicates the unused ABCD bits to be sent.
OCT h3cVoDIfR2ABCDReverseABCD	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.3	OCTET STRING	read-write	This object indicates whether the ABCD bits should be inverted. '0' : disable invertion. '1' : enable invertion.
OCT h3cVoDIfR2ABCDRxAnswer	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.11	OCTET STRING	read-write	This object indicates the ANSWER line signaling to be received.
OCT h3cVoDIfR2ABCDRxBlocking	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.19	OCTET STRING	read-write	This object indicates the BLOCKING line signaling to be received.
OCT h3cVoDIfR2ABCDRxClearBack	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.15	OCTET STRING	read-write	This object indicates the CLEAR_BACKWARD line signaling to be received.
OCT h3cVoDIfR2ABCDRxClearForward	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.13	OCTET STRING	read-write	This object indicates the CLEAR_FORWARD line signaling to be received.
OCT h3cVoDIfR2ABCDRxIdle	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.5	OCTET STRING	read-write	This object indicates the IDLE line signaling to be received.
OCT h3cVoDIfR2ABCDRxReleaseGuard	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.17	OCTET STRING	read-write	This object indicates the RELEASE_GUARD line signaling to be received.
OCT h3cVoDIfR2ABCDRxSeizure	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.7	OCTET STRING	read-write	This object indicates the SEIZURE line signaling to be received.
OCT h3cVoDIfR2ABCDRxSeizureAck	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.9	OCTET STRING	read-write	This object indicates the SEIZURE_ACK line signaling to be received.
OCT h3cVoDIfR2ABCDSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.21	OCTET STRING	read-only	This object indicates the port subscriber line name.
OCT h3cVoDIfR2ABCDTxAnswer	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.12	OCTET STRING	read-write	This object indicates the ANSWER line signaling to be sent.
OCT h3cVoDIfR2ABCDTxBlocking	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.20	OCTET STRING	read-write	This object indicates the BLOCKING line signaling to be sent.
OCT h3cVoDIfR2ABCDTxClearBack	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.16	OCTET STRING	read-write	This object indicates the CLEAR_BACKWARD line signaling to be sent.
OCT h3cVoDIfR2ABCDTxClearForward	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.14	OCTET STRING	read-write	This object indicates the CLEAR_FORWARD line signaling to be sent.
OCT h3cVoDIfR2ABCDTxIdle	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.6	OCTET STRING	read-write	This object indicates the IDLE line signaling to be sent.
OCT h3cVoDIfR2ABCDTxReleaseGuard	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.18	OCTET STRING	read-write	This object indicates the RELEASE_GUARD line signaling to be sent.
OCT h3cVoDIfR2ABCDTxSeizure	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.8	OCTET STRING	read-write	This object indicates the SEIZURE line signaling to be sent.
OCT h3cVoDIfR2ABCDTxSeizureAck	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1.10	OCTET STRING	read-write	This object indicates the SEIZURE_ACK line signaling to be sent.
INT h3cVoDIfR2Ani	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.30	INTEGER	read-write	This object indicates whether to return the calling category and the call number during the MFC procedure.
I32 h3cVoDIfR2BillingCategory	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.3	Integer32	read-write	This object indicates the value of BILLING CATEGORY during the MFC procedure.
I32 h3cVoDIfR2CallCreateInA	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.23	Integer32	read-write	This object indicates the value of CALLCREATE IN GROUP A during the MFC procedure.
I32 h3cVoDIfR2CallingCategory	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.4	Integer32	read-write	This object indicates the value of CALLING CATEGORY during the MFC procedure.
h3cVoDIfR2CapabilityCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1		not-accessible	The entry of h3cVoDIfR2CapabilityCfgTable.
h3cVoDIfR2CapabilityCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5		not-accessible	This table contains information about capability parameters for digital r2 voice interface.
I32 h3cVoDIfR2CapCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfR2CapCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfR2CapCfgSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.15	OCTET STRING	read-only	This object indicates the port subscriber line name.
INT h3cVoDIfR2CfgAnswer	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.7	INTEGER	read-write	This object indicates whether the ANSWER signal is enabled.
INT h3cVoDIfR2CfgClearForwardAck	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.4	INTEGER	read-write	This object indicates whether the CLEAR_FORWARD_ACK signal is enabled.
INT h3cVoDIfR2CfgCountryMode	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.3	INTEGER	read-write	This object indicates the value of country mode.
I32 h3cVoDIfR2CfgDebounceTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.3	Integer32	read-write	This object indicates the minimum duration which is the line signal going to persist.
I32 h3cVoDIfR2CfgDlAnswerTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.7	Integer32	read-write	This object indicates the value of answer timer.
I32 h3cVoDIfR2CfgDlClearBackTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.8	Integer32	read-write	This object indicates the value of clear back timer.
I32 h3cVoDIfR2CfgDlClearForwardT	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.9	Integer32	read-write	This object indicates the value of clear forward timer.
I32 h3cVoDIfR2CfgDlReanswerTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.11	Integer32	read-write	This object indicates the value of reanswer timer.
I32 h3cVoDIfR2CfgDlRelGuardTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.12	Integer32	read-write	This object indicates the value of release guard timer.
INT h3cVoDIfR2CfgDlSeizureAck	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.5	INTEGER	read-write	This object indicates whether the SEIZURE_ACK signal is enabled.
I32 h3cVoDIfR2CfgDlSeizureTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.10	Integer32	read-write	This object indicates the value of seizure timer.
INT h3cVoDIfR2CfgDTMF	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.6	INTEGER	read-write	This object indicates whether the DTMF(Dual Tone Multi-Frequency) is enabled.
I32 h3cVoDIfR2CfgDTMFTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.14	Integer32	read-write	This object indicates the value of DTMF(Dual Tone Multi-Frequency) timer.
INT h3cVoDIfR2CfgFinalCallnum	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.9	INTEGER	read-write	This object indicates whether the FINAL_CALL_NUMBER signal is enabled.
INT h3cVoDIfR2CfgForceMetering	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.10	INTEGER	read-write	This object indicates whether the METERING signal is enabled.
I32 h3cVoDIfR2CfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
INT h3cVoDIfR2CfgGroupB	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.3	INTEGER	read-write	This object indicates whether the group B process is enabled.
I32 h3cVoDIfR2CfgMfcGroupBTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.13	Integer32	read-write	This object indicates the value of group B timer.
I32 h3cVoDIfR2CfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
INT h3cVoDIfR2CfgReanswer	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.8	INTEGER	read-write	This object indicates whether the REANSWER signal is enabled.
INT h3cVoDIfR2CfgSelectMode	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.6	INTEGER	read-write	This object indicates the trunk mode to be selected: min set selected trunk mode to min-mode. max set selected trunk mode to max-mode. minpoll set selected trunk mode to min-poll-mode. maxpoll set selected trunk mode to max-poll-mode.
INT h3cVoDIfR2CfgSendRingBack	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.11	INTEGER	read-write	This object indicates whether to send the ring back tone.
I32 h3cVoDIfR2CfgSendringBackTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.4	Integer32	read-write	This object indicates the minimum duration which is the ring back going to persist.
INT h3cVoDIfR2CfgSendRingBusy	1.3.6.1.4.1.43.45.1.10.2.39.4.3.5.1.12	INTEGER	read-write	This object indicates whether to send the busy tone.
I32 h3cVoDIfR2CfgSendringBusyTime	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.5	Integer32	read-write	This object indicates the minimum duration which is the ring busy going to persist.
INT h3cVoDIfR2CfgSpecialChar	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.4	INTEGER	read-write	This object indicates the special character(A,B,C,D,#,*).
I32 h3cVoDIfR2CfgSpecialSignal	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.5	Integer32	read-write	This object indicates the signal of special character.
OCT h3cVoDIFR2CfgSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1.7	OCTET STRING	read-only	This object indicates the port subscriber line name.
I32 h3cVoDIfR2Congestion	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.5	Integer32	read-write	This object indicates the value of CONGESTION during the MFC procedure.
I32 h3cVoDIfR2DemandRefused	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.6	Integer32	read-write	This object indicates the value of DEMAND REFUSED during the MFC procedure.
I32 h3cVoDIfR2DigitEnd	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.7	Integer32	read-write	This object indicates the value of DIGIT END during the MFC procedure.
I32 h3cVoDIfR2MfcCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfR2MfcCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
I32 h3cVoDIfR2Nullnum	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.8	Integer32	read-write	This object indicates the value of NULL NUMBER during the MFC procedure.
I32 h3cVoDIfR2PulseSignalPersistT	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.6	Integer32	read-write	This object indicates the value of pulse signal persistence timer.
I32 h3cVoDIfR2ReqBillingCategory	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.9	Integer32	read-write	This object indicates the value of REQUESTING BILLING category during the MFC procedure.
I32 h3cVoDIfR2ReqCalledNumSwitchA	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.26	Integer32	read-write	This object indicates the value of REQUEST CALLED NUMBER AND SWITCH TO GROUP A during the MFC procedure.
I32 h3cVoDIfR2ReqCallingCategory	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.10	Integer32	read-write	This object indicates the value of REQUESTING CALLING CATEGORY during the MFC procedure.
I32 h3cVoDIfR2ReqCallingnumOffset	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.22	Integer32	read-write	This object indicates the value of CALLING NUMBER OFFSET during the MFC procedure.
I32 h3cVoDIfR2ReqCurCalledNumInC	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.25	Integer32	read-write	This object indicates the value of CURRENT CALLED NUMBER IN GROUP C during the MFC procedure.
I32 h3cVoDIfR2ReqCurrentdigit	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.11	Integer32	read-write	This object indicates the value of REQUESTING CURRENT DIGIT during the MFC procedure.
I32 h3cVoDIfR2ReqFirstCalledNumInC	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.24	Integer32	read-write	This object indicates the value of FIRST CALLED NUMBER IN GROUP C during the MFC procedure.
I32 h3cVoDIfR2ReqFirstCallingnum	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.12	Integer32	read-write	This object indicates the value of REQUESTING FIRST CALLING NUMBER during the MFC procedure.
I32 h3cVoDIfR2ReqFirstDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.13	Integer32	read-write	This object indicates the value of REQUESTING FIRST DIGIT during the MFC procedure.
I32 h3cVoDIfR2ReqLastFirstDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.16	Integer32	read-write	This object indicates the value of REQUESTING LAST FIRST DIGIT during the MFC procedure.
I32 h3cVoDIfR2ReqLastSecondDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.17	Integer32	read-write	This object indicates the value of REQUESTING LAST SECOND DIIGT during the MFC procedure.
I32 h3cVoDIfR2ReqLastThirdDigit	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.18	Integer32	read-write	This object indicates the value of REQUESTING LAST LAST THIRD DIGIT during the MFC procedure.
I32 h3cVoDIfR2ReqNextCallednum	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.14	Integer32	read-write	This object indicates the value of REQUESTING NEXT CALLED NUMBER during the MFC procedure.
I32 h3cVoDIfR2ReqNextCallingnum	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.15	Integer32	read-write	This object indicates the value of REQUESTING NEXT CALLING NUMBER during the MFC procedure.
I32 h3cVoDIfR2ReqSpecialSignal	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.27	Integer32	read-write	This object indicates the value of SPECIAL SIGNAL during the MFC procedure.
I32 h3cVoDIfR2ReqSwitchGroupB	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.19	Integer32	read-write	This object indicates the value of REQUESTING SWITCH GROUP B during the MFC procedure.
OCT h3cVoDIfR2SubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.31	OCTET STRING	read-only	This object indicates the port subscriber line name.
I32 h3cVoDIfR2SubscriberAbnormal	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.29	Integer32	read-write	This object indicates the value of SUBSCRIBER ABNORMAL during the MFC procedure.
I32 h3cVoDIfR2SubscriberBusy	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.21	Integer32	read-write	This object indicates the value of SUBSCRIBER BUSY.
I32 h3cVoDIfR2SubscriberCharge	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.28	Integer32	read-write	This object indicates the value of SUBSCRIBER CHARGE during the MFC procedure.
I32 h3cVoDIfR2SubscriberIdle	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1.20	Integer32	read-write	This object indicates the value of SUSCRIBER IDLE during the MFC procedure.
I32 h3cVoDIfR2TimeCfgGroup	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.2	Integer32	not-accessible	This object indicates the group number of a voice digital module.
I32 h3cVoDIfR2TimeCfgPort	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.1	Integer32	not-accessible	This object indicates the port of a voice digital module.
OCT h3cVoDIfR2TimeCfgSubLine	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1.15	OCTET STRING	read-only	This object indicates the port subscriber line name.
h3cVoDigitalIfCommonCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1.1		not-accessible	The entry of h3cVoDigitalIfCommonCfgTable, which is automatically created when a digital voice module has been found.
h3cVoDigitalIfCommonCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.1.1		not-accessible	This table contains the information about configurable parameters for a digital voice interface.
h3cVoDigitalIfCommonObjects	1.3.6.1.4.1.43.45.1.10.2.39.4.1
h3cVoDigitalIfEMABCDCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2.1		not-accessible	The entry of h3cVoDigitalIfEMABCDCfgTable.
h3cVoDigitalIfEMABCDCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.2.2		not-accessible	This table contains the information about ABCD bits parameters for a digital EM voice interface.
h3cVoDigitalIfEMCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1.1		not-accessible	The entry of h3cVoDigitalIfEMCfgTable.
h3cVoDigitalIfEMCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.2.1		not-accessible	This table contains the information about configurable parameters for a digital EM voice interface.
h3cVoDigitalIfEMObjects	1.3.6.1.4.1.43.45.1.10.2.39.4.2
h3cVoDigitalIfEMTimerEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4.1		not-accessible	The entry of h3cVoDigitalIfEMTimerTable.
h3cVoDigitalIfEMTimerTable	1.3.6.1.4.1.43.45.1.10.2.39.4.2.4		not-accessible	This table contains the timer parameters for a digital EM voice interface.
h3cVoDigitalIfR2ABCDCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2.1		not-accessible	The entry of h3cVoDigitalIfR2ABCDCfgTable.
h3cVoDigitalIfR2ABCDCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.3.2		not-accessible	This table contains the information about ABCD bits parameters for a digital r2 voice interface.
h3cVoDigitalIfR2CfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1.1		not-accessible	The entry of h3cVoDigitalIfR2CfgTable.
h3cVoDigitalIfR2CfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.3.1		not-accessible	This table contains information about general configurable parameters for digital r2 voice interface.
h3cVoDigitalIfR2MfcCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3.1		not-accessible	The entry of h3cVoDigitalIfR2MfcCfgTable.
h3cVoDigitalIfR2MfcCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.3.3		not-accessible	This table contains information about MFC(Multi-Frequency Control) configurable parameters for digital r2 voice interface.
h3cVoDigitalIfR2Objects	1.3.6.1.4.1.43.45.1.10.2.39.4.3
h3cVoDigitalIfR2TimerCfgEntry	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4.1		not-accessible	The entry of h3cVoDigitalIfR2TimeCfgTable.
h3cVoDigitalIfR2TimerCfgTable	1.3.6.1.4.1.43.45.1.10.2.39.4.3.4		not-accessible	This table contains information about time parameters for digital r2 voice interface.
h3cVoiceDigitalInterface	1.3.6.1.4.1.43.45.1.10.2.39.4			The MIB file is to provide the definition of the general digital voice interface configuration.

RFC description

Digital voice interface configuration MIB for managing voice module parameters and settings.

Start monitoring H3C/3Com voice gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-VODIGITALIF-MIB

What Is A3COM-HUAWEI-VODIGITALIF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description