AP-SYSTEM-NETWORK

All MIBs › AP-SYSTEM-NETWORK

Organization: PEPWAVE

Last Updated: 2020-11-08

Category: Telephony and VoIP, Vendor: Acme Packet

Description: Acme Packet SBC network interface and routing configuration management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AP-SYSTEM-NETWORK?

AP-SYSTEM-NETWORK is a proprietary MIB module belonging to Acme Packet's Session Border Controller (SBC) product family, used for carrier and enterprise VoIP/SIP signaling infrastructure. It exposes system-level network configuration data covering the SBC's interfaces, addressing, and routing setup for control and media-plane connectivity. As part of system health monitoring, it lets administrators confirm that network interfaces on the SBC are correctly configured and operationally reachable, which is foundational to detecting connectivity faults, misrouted traffic, or interface-level outages on the appliance. It is typically layered on top of, and complements, standard IETF interface and IP addressing conventions (IF-MIB/IP-MIB style modeling) rather than replacing them. It is deployed in telecom and enterprise networks wherever Acme Packet (later Oracle) SBCs terminate or relay SIP/RTP sessions at network edges, where engineers often perform an AP-SYSTEM-NETWORK download to load the module into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AP-SYSTEM-NETWORK. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Peplink/Pepwave Enterprise WiFi access point network-configuration module

Monitoring Examples

No object or table names were provided in the source data for this module, so a concrete polling example cannot be grounded in real identifiers; in general terms, an administrator would be expected to poll interface and route configuration objects to confirm the SBC's network-facing interfaces remain correctly addressed and active.

What Can Be Monitored

network interface configuration
interface addressing/routing setup
SBC network connectivity status

Imported Objects

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
pepwave	1.3.6.1.4.1.27662
productID	1.3.6.1.4.1.27662.200
apMib	1.3.6.1.4.1.27662.200.1
apGeneralMib	1.3.6.1.4.1.27662.200.1.1
ap_system_network_mib	1.3.6.1.4.1.27662.200.1.1.2			The MIB module for PEPWAVE Enterprise WiFi AP. iso(1).org(3).dod(6).internet(1).private(4). enterprises(1).pepwave(27662).productID(200).apMib(1).apGeneralMib(1).ap-system-network-mib(2)
apNetworkInfo	1.3.6.1.4.1.27662.200.1.1.2.1
apWanInfo	1.3.6.1.4.1.27662.200.1.1.2.1.1
INT apCurrentIpAddressMode	1.3.6.1.4.1.27662.200.1.1.2.1.1.1	INTEGER	read-only	This attribute indicates the current IP address mode of the AP.
IP apCurrentIpAddress	1.3.6.1.4.1.27662.200.1.1.2.1.1.2	IpAddress	read-only	This attribute indicates the current IP address of the AP.
IP apCurrentSubnetMask	1.3.6.1.4.1.27662.200.1.1.2.1.1.3	IpAddress	read-only	This attribute indicates the current subnet mask of the AP.
IP apCurrentGateway	1.3.6.1.4.1.27662.200.1.1.2.1.1.4	IpAddress	read-only	This attribute indicates the current default gateway of the AP.
IP apCurrentDns	1.3.6.1.4.1.27662.200.1.1.2.1.1.5	IpAddress	read-only	This attribute indicates the current dns of the AP.
apPppoeInfo	1.3.6.1.4.1.27662.200.1.1.2.1.4
INT apPppoeStatus	1.3.6.1.4.1.27662.200.1.1.2.1.4.1	INTEGER	read-only	This attribute indicates the status of PPPoE.
OCT apPppoeStatusMessage	1.3.6.1.4.1.27662.200.1.1.2.1.4.2	OCTET STRING	read-only	This attribute indicates the status message of PPPoE.
apNetworkConfig	1.3.6.1.4.1.27662.200.1.1.2.2
apWanConfig	1.3.6.1.4.1.27662.200.1.1.2.2.1
INT apKeepDefaultIp	1.3.6.1.4.1.27662.200.1.1.2.2.1.1	INTEGER	read-write	This attribute indicates the keep default IP status of AP.
INT apIpAddressMode	1.3.6.1.4.1.27662.200.1.1.2.2.1.2	INTEGER	read-write	This attribute indicates the IP address mode of the AP.
IP apIpAddress	1.3.6.1.4.1.27662.200.1.1.2.2.1.3	IpAddress	read-write	This attribute indicates the static management IP address of the AP.
IP apSubnetMask	1.3.6.1.4.1.27662.200.1.1.2.2.1.4	IpAddress	read-write	This attribute indicates the static netmask of the management interface.
IP apGateway	1.3.6.1.4.1.27662.200.1.1.2.2.1.5	IpAddress	read-write	This attribute indicates the static gateway IP address for the management interface.
IP apDns	1.3.6.1.4.1.27662.200.1.1.2.2.1.6	IpAddress	read-write	This attribute indicates the static DNS for the management interface.
apLanConfig	1.3.6.1.4.1.27662.200.1.1.2.2.2
IP apLanIpAddress	1.3.6.1.4.1.27662.200.1.1.2.2.2.1	IpAddress	read-write	This attribute indicates the IP address of the LAN interface.
IP apLanSubnetMask	1.3.6.1.4.1.27662.200.1.1.2.2.2.2	IpAddress	read-write	This attribute indicates the subnet mask of the LAN interface.
INT apLanDhcpServer	1.3.6.1.4.1.27662.200.1.1.2.2.2.3	INTEGER	read-write	This attribute indicates the status of the LAN DHCP Server.
IP apLanDhcpServerStartRange	1.3.6.1.4.1.27662.200.1.1.2.2.2.4	IpAddress	read-write	This attribute indicates the start range of the LAN DHCP Server.
IP apLanDhcpServerStopRange	1.3.6.1.4.1.27662.200.1.1.2.2.2.5	IpAddress	read-write	This attribute indicates the stop range of the LAN DHCP Server.
IP apLanDhcpServerSubnetMask	1.3.6.1.4.1.27662.200.1.1.2.2.2.6	IpAddress	read-write	This attribute indicates the subnet mask of the LAN DHCP Server.
IP apLanDhcpServerBroadcast	1.3.6.1.4.1.27662.200.1.1.2.2.2.7	IpAddress	read-write	This attribute indicates the broadcast address of the LAN DHCP Server.
IP apLanDhcpServerGateway	1.3.6.1.4.1.27662.200.1.1.2.2.2.8	IpAddress	read-write	This attribute indicates the gateway of the LAN DHCP Server.
IP apLanDhcpServerDns1	1.3.6.1.4.1.27662.200.1.1.2.2.2.9	IpAddress	read-write	This attribute indicates the first DNS server of the LAN DHCP Server.
IP apLanDhcpServerDns2	1.3.6.1.4.1.27662.200.1.1.2.2.2.10	IpAddress	read-write	This attribute indicates the second DNS server of the LAN DHCP Server.
IP apLanDhcpServerDns3	1.3.6.1.4.1.27662.200.1.1.2.2.2.11	IpAddress	read-write	This attribute indicates the third DNS server of the LAN DHCP Server.
OCT apLanDhcpDomain	1.3.6.1.4.1.27662.200.1.1.2.2.2.12	OCTET STRING	not-accessible	This attribute indicates the domain of the LAN DHCP Server.
INT apLanDhcpRelease	1.3.6.1.4.1.27662.200.1.1.2.2.2.13	INTEGER	read-write	This attribute indicates the lease time of the LAN DHCP Server.
apLanReservationTable	1.3.6.1.4.1.27662.200.1.1.2.2.2.14		not-accessible	LAN Reservation Table.
apLanReservationEntry	1.3.6.1.4.1.27662.200.1.1.2.2.2.14.1		not-accessible	An entry in the apLanReservationTable.
INT apLanReservationIndex	1.3.6.1.4.1.27662.200.1.1.2.2.2.14.1.1	INTEGER	read-only	This attribute indicates the LAN Reservation index
ROW apLanReservationRowControl	1.3.6.1.4.1.27662.200.1.1.2.2.2.14.1.2	RowStatus	read-create	The LAN Reservation status. Supported values: active(1) - valid entry notReady(3) - non-valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry
MAC apLanReservationMacAddress	1.3.6.1.4.1.27662.200.1.1.2.2.2.14.1.3	MacAddress	read-write	This field indicates a MAC address entry in the LAN Reservation. Remarks: Input format: 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX OR XX:XX:XX:XX:XX:XX OR XX-XX-XX-XX-XX-XX (examples: 0xab 0xcd 0xef 0x01 0x02 0x03 OR ab:cd:ef:01:02:03 OR ab-cd-ef-01-02-03) X: [0:9] or [a:f] or [A:F] * Please don 't enter duplicate MAC address. *
IP apLanReservationIp	1.3.6.1.4.1.27662.200.1.1.2.2.2.14.1.4	IpAddress	read-write	This field indicates a IP address entry in the LAN Reservation.
apPppoeConfig	1.3.6.1.4.1.27662.200.1.1.2.2.3
OCT apPppoeUsername	1.3.6.1.4.1.27662.200.1.1.2.2.3.1	OCTET STRING	read-write	This attribute indicates the username of PPPoE.
OCT apPppoePassword	1.3.6.1.4.1.27662.200.1.1.2.2.3.2	OCTET STRING	read-write	This attribute indicates the password of PPPoE.
OCT apPppoeServiceName	1.3.6.1.4.1.27662.200.1.1.2.2.3.3	OCTET STRING	read-write	This attribute indicates the service name of PPPoE.
apDmzConfig	1.3.6.1.4.1.27662.200.1.1.2.2.4
INT apDmzStatus	1.3.6.1.4.1.27662.200.1.1.2.2.4.1	INTEGER	read-write	This attribute indicates the status of DMZ.
IP apDmzIp	1.3.6.1.4.1.27662.200.1.1.2.2.4.2	IpAddress	read-write	This attribute indicates the IP address of DMZ.
apPortForwardTable	1.3.6.1.4.1.27662.200.1.1.2.2.5		not-accessible	LAN Port Forward Table.
apPortForwardEntry	1.3.6.1.4.1.27662.200.1.1.2.2.5.1		not-accessible	An entry in the apPortForwardTable.
INT apPortForwardIndex	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.1	INTEGER	read-only	This attribute indicates the port forward index
ROW apPortForwardRowControl	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.2	RowStatus	read-create	The port forward status. Supported values: active(1) - valid entry notReady(3) - non-valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry
OCT apPortForwardName	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.3	OCTET STRING	read-write	This field indicates the name of port forward.
IP apPortForwardToIp	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.4	IpAddress	read-write	This field indicates the to IP address of port forward.
INT apPortForwardPortProtocol	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.5	INTEGER	read-write	This field indicates the protocol of port forward.
INT apPortForwardAppServiceType	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.6	INTEGER	read-write	This field indicates the service type of port forward.
INT apPortForwardPortType	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.7	INTEGER	read-write	This field indicates the port type of port forward.
OCT apPortForwardFromPort	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.8	OCTET STRING	read-write	This field indicates the from port of port forward.
OCT apPortForwardToPort	1.3.6.1.4.1.27662.200.1.1.2.2.5.1.9	OCTET STRING	read-write	This field indicates the to port of port forward.

RFC description

Vendor-private MIB for managing access point (AP) system network configuration and connectivity parameters.

Start monitoring Peplink/Pepwave Enterprise WiFi access points with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AP-SYSTEM-NETWORK

What Is AP-SYSTEM-NETWORK?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description