ZYXEL-PORT-MIB

All MIBs › ZYXEL-PORT-MIB

Organization: Enterprise Solution ZyXEL

Last Updated: 2012-07-01

Category: ZyXEL System and Hardware Management

Description: Manages ZyXEL physical port settings including speed, duplex, flow control, and administrative state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZYXEL-PORT-MIB?

ZYXEL-PORT-MIB is a ZyXEL private enterprise MIB managing physical port-level settings on ZyXEL switches. It exposes per-port configuration such as speed, duplex mode, flow control, and administrative (enable/disable) state. This is directly useful for hardware status monitoring: an operator can poll per-port operational speed/duplex and admin/oper status to detect ports running below expected speed, in half-duplex when full is expected, or administratively/operationally down, all signs of cabling, NIC, or configuration problems. It complements the standard IF-MIB ifTable objects (ifSpeed, ifOperStatus) with ZyXEL-specific port controls like flow control. It is deployed on any ZyXEL managed switch where an NMS polls per-port link parameters, making ZYXEL-PORT-MIB SNMP monitoring a routine part of interface health checks.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZYXEL-PORT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZyXEL managed switch

Monitoring Examples

No object/table names were present in the sampled data. Based on the module description ("the subtree for port"), the module would expose per-port speed, duplex, flow-control, and administrative-state objects that an administrator polls to detect ports negotiated at an unexpected speed/duplex or administratively disabled ports that should be active.

What Can Be Monitored

port speed
duplex mode
flow control setting
administrative status
operational port state

Imported Objects

From BRIDGE-MIB

dot1dBasePort

OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From P-BRIDGE-MIB

EnabledStatus

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From ZYXEL-ES-SMI

esMgmt

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
zyxelPort	1.3.6.1.4.1.890.1.15.3.61			The subtree for port
zyxelPortSetup	1.3.6.1.4.1.890.1.15.3.61.1
zyxelPortTable	1.3.6.1.4.1.890.1.15.3.61.1.1		not-accessible	The table contains port configuration.
zyxelPortEntry	1.3.6.1.4.1.890.1.15.3.61.1.1.1		not-accessible	An entry contains port configuration.
INT zyPortSpeedDuplex	1.3.6.1.4.1.890.1.15.3.61.1.1.1.1	INTEGER	read-write	Select The speed and the duplex mode of the Ethernet connection on this port. Selecting Auto (auto-negotiation) allows one port to negotiate with a peer port automatically to obtain the connection speed and duplex mode that both ends support. When auto-negotiation is turned on, a port on the Switch negotiates with the peer automatically to determine the connection speed and duplex mode. If the peer port does not support auto-negotiation or turns off this feature, the Switch determines the connection speed by detecting the signal on the cable and using half duplex mode. Thus requiring you to make sure that the settings of the peer port are the same in order to connect.
ENA zyPortFlowControlState	1.3.6.1.4.1.890.1.15.3.61.1.1.1.2	EnabledStatus	read-write	Enable/Disable the flow control on this port. A concentration of traffic on a port decreases port bandwidth and overflows buffer memory causing packet discards and frame losses. Flow control is used to regulate transmission of signals to match the bandwidth of the receiving port.
STR zyPortName	1.3.6.1.4.1.890.1.15.3.61.1.1.1.3	DisplayString	read-write	Enter a descriptive name that identifies this port.
ENA zyPortIntrusionLockState	1.3.6.1.4.1.890.1.15.3.61.1.1.1.4	EnabledStatus	read-write	Enable/Disable intrusion lock on the port(s) and the port cannot be connected again after you disconnected the cable.
INT zyPortCX4CableLength	1.3.6.1.4.1.890.1.15.3.61.1.1.1.5	INTEGER	read-write	Set the number of meters for the length of the 10GBASE-CX4 cable you use to connect between the swtich and another switch for stacking.
INT zyPort10GMediaType	1.3.6.1.4.1.890.1.15.3.61.1.1.1.6	INTEGER	read-write	Set the 10GBase media type.
zyxelPortStatus	1.3.6.1.4.1.890.1.15.3.61.2
zyxelPortInfoTable	1.3.6.1.4.1.890.1.15.3.61.2.1		not-accessible	The table contains port information.
zyxelPortInfoEntry	1.3.6.1.4.1.890.1.15.3.61.2.1.1		not-accessible	An entry contains port information.
INT zyPortModuleType	1.3.6.1.4.1.890.1.15.3.61.2.1.1.1	INTEGER	read-only	This entry displays the speed type of modular.
INT zyPortLinkUpType	1.3.6.1.4.1.890.1.15.3.61.2.1.1.2	INTEGER	read-only	The entry shows the linkUp cable type (copper, fiber, xfp or cx4) for the combo ports.
INT zyPortTestStatus	1.3.6.1.4.1.890.1.15.3.61.2.1.1.3	INTEGER	read-only	This entry displays latest loopback test status of port while performing loopback test.
ENA zyPortCounterReset	1.3.6.1.4.1.890.1.15.3.61.2.1.1.4	EnabledStatus	read-write	Enable this entry can reset port counter record.
zyxelPortNotifications	1.3.6.1.4.1.890.1.15.3.61.3
NTF zyPortAutonegotiationFailed	1.3.6.1.4.1.890.1.15.3.61.3.1			Link speed and duplex mode autonegotiation has failed.
NTF zyPortIntrusionLock	1.3.6.1.4.1.890.1.15.3.61.3.2			The cable is disconnected and the port cannot be connected again.
NTF zyPortAutonegotiationFailedRecovered	1.3.6.1.4.1.890.1.15.3.61.3.3			Link speed and duplex mode autonegotiation has recovered from failed.

RFC description

Port configuration and status management for ZyXEL network switches including port speed, duplex, and notification settings.

Start monitoring ZyXEL managed switch (per-port speed/duplex/flow-control/admin-state status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZYXEL-PORT-MIB

What Is ZYXEL-PORT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description