All MIBs › XEDIA-DS1-MIB › xdsx1CfgLoopbackConfig
xdsx1CfgLoopbackConfig
Module: XEDIA-DS1-MIB
OID (symbolic): XEDIA-DS1-MIB::xdsx1CfgLoopbackConfig
OID (numeric): 1.3.6.1.4.1.838.3.18.2.1.1.13
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This variable represents the loopback configuration of the DS1 interface. Agents supporting read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean:
xdsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value.
xdsx1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function.
xdsx1LineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out.
xdsx1Framer
xdsx1Analog
What is xdsx1CfgLoopbackConfig?
Sets the loopback mode for this DS1 interface: noLoop(1, the default, no loopback), remotePayloadLoop(2, loops the received signal back after it passes through framing), remoteLineLoop(3, loops the signal back with minimal penetration), or localFramer(4)/localAnalog(5); an agent returns badValue for an unsupported mode.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.838.3.18.2.1.1.13 snmpwalk -v2c -c public <target> XEDIA-DS1-MIB::xdsx1CfgLoopbackConfig
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.838.3.18.2.1.1.13.1 snmpget -v2c -c public <target> XEDIA-DS1-MIB::xdsx1CfgLoopbackConfig.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.838.3.18.2.1.1.13.1 i <value>
Start monitoring Xedia Corporation routers/access devices with DS1 (T1/E1) interfaces (bit-level alarm/loopback-test status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the XEDIA-DS1-MIB::xdsx1CfgLoopbackConfig OID value, configure state conditions and alerts, and monitor any Xedia Corporation routers/access devices with DS1 (T1/E1) interfaces (bit-level alarm/loopback-test status) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.838 | xedia | XEDIA-REG |
| 1.3.6.1.4.1.838.3 | xediaMibs | XEDIA-REG |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.838.3.18 | xediaDs1MIB | XEDIA-DS1-MIB |
| 1.3.6.1.4.1.838.3.18.2 | xDs1Tables | XEDIA-DS1-MIB |
| 1.3.6.1.4.1.838.3.18.2.1 | xDsx1ConfigTable | XEDIA-DS1-MIB |
| 1.3.6.1.4.1.838.3.18.2.1.1 | xDsx1ConfigEntry | XEDIA-DS1-MIB |
| 1.3.6.1.4.1.838.3.18.2.1.1.13 | xdsx1CfgLoopbackConfig | XEDIA-DS1-MIB |