UNISYS-MIB

All MIBs › UNISYS-MIB

Description: Unisys enterprise MIB (1990) covering system, interfaces, IP, TCP, UDP, FDDI, X.25, RIP, and EGP management objects for Unisys network equipment

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is UNISYS-MIB?

This is a 1990-era Unisys enterprise vendor MIB covering system identification and core internetworking protocols — interfaces, IP, TCP, UDP, FDDI, X.25, RIP, and EGP — for Unisys network equipment of that era. It exposes protocol and interface statistics rather than environmental sensors, spanning link-layer FDDI/X.25 status and network/transport-layer counters. Monitoring value here is mainly software/protocol operational status: interface up/down state doubles as a hardware link-health indicator, and routing protocol (RIP/EGP) state reflects connectivity health of the device. Given its object groupings, it closely mirrors the structure of the standard MIB-II (RFC 1213), adding FDDI and X.25-specific extensions on top. It applies to legacy Unisys routers and gateways from early enterprise/mainframe-adjacent TCP/IP networks, and is largely of historical interest today. Engineers can download the UNISYS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UNISYS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Unisys network router/gateway (legacy, early 1990s)

Monitoring Examples

No specific object or table names were provided for this module. Given its stated coverage, it likely follows the MIB-II pattern with an interface table for FDDI and X.25 ports (link status, packet counters) plus TCP/UDP connection and RIP/EGP routing tables, but none of these names could be confirmed from the available data.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1065-SMI

Counter
Gauge
IpAddress
NetworkAddress

OIDs

OID symbolic	OID numeric	Type	Access
internet	1.3.6.1
private	1.3.6.1.4
enterprises	1.3.6.1.4.1
unisys	1.3.6.1.4.1.16
u_mgmt	1.3.6.1.4.1.16.2
u_mib	1.3.6.1.4.1.16.2.1
u_system	1.3.6.1.4.1.16.2.1.1
INT u_systemAction	1.3.6.1.4.1.16.2.1.1.1	INTEGER	read-write
INT u_systemReboots	1.3.6.1.4.1.16.2.1.1.2	INTEGER	read-only
INT u_systemErrorCode	1.3.6.1.4.1.16.2.1.1.3	INTEGER	read-only
u_interfaces	1.3.6.1.4.1.16.2.1.2
u_ifTable	1.3.6.1.4.1.16.2.1.2.1		read-write
u_ifEntry	1.3.6.1.4.1.16.2.1.2.1.1		read-write
INT u_ifEthernetArpWait	1.3.6.1.4.1.16.2.1.2.1.1.1	INTEGER	read-write
IP u_ifIpAddr	1.3.6.1.4.1.16.2.1.2.1.1.2	IpAddress	read-write
IP u_ifSubnetMask	1.3.6.1.4.1.16.2.1.2.1.1.3	IpAddress	read-write
INT u_ifHdlcBaudRate	1.3.6.1.4.1.16.2.1.2.1.1.4	INTEGER	read-write
INT u_ifHdlcRto	1.3.6.1.4.1.16.2.1.2.1.1.5	INTEGER	read-write
INT u_ifHdlcAckTo	1.3.6.1.4.1.16.2.1.2.1.1.6	INTEGER	read-write
INT u_ifHdlcSabmInterval	1.3.6.1.4.1.16.2.1.2.1.1.7	INTEGER	read-write
INT u_ifHdlcRnrInterval	1.3.6.1.4.1.16.2.1.2.1.1.8	INTEGER	read-write
INT u_ifHdlcClockType	1.3.6.1.4.1.16.2.1.2.1.1.9	INTEGER	read-write
INT u_ifHdlcDCE	1.3.6.1.4.1.16.2.1.2.1.1.10	INTEGER	read-write
INT u_ifHdlcThrowaway	1.3.6.1.4.1.16.2.1.2.1.1.11	INTEGER	read-write
INT u_ifHdlcAckCount	1.3.6.1.4.1.16.2.1.2.1.1.12	INTEGER	read-write
INT u_ifFddiArpWait	1.3.6.1.4.1.16.2.1.2.1.1.13	INTEGER	read-write
u_at	1.3.6.1.4.1.16.2.1.3
u_icmp	1.3.6.1.4.1.16.2.1.5
u_tcp	1.3.6.1.4.1.16.2.1.6
INT u_tcpRetransTo	1.3.6.1.4.1.16.2.1.6.1	INTEGER	read-write
INT u_tcpRtoMin	1.3.6.1.4.1.16.2.1.6.2	INTEGER	read-write
INT u_tcpRtoMax	1.3.6.1.4.1.16.2.1.6.3	INTEGER	read-write
INT u_tcpWakeup	1.3.6.1.4.1.16.2.1.6.4	INTEGER	read-write
INT u_tcpAckTime	1.3.6.1.4.1.16.2.1.6.5	INTEGER	read-write
INT u_tcpTimeToLive	1.3.6.1.4.1.16.2.1.6.6	INTEGER	read-write
INT u_tcpThruput	1.3.6.1.4.1.16.2.1.6.7	INTEGER	read-write
INT u_tcpFlowAck	1.3.6.1.4.1.16.2.1.6.8	INTEGER	read-write
u_udp	1.3.6.1.4.1.16.2.1.7
u_egp	1.3.6.1.4.1.16.2.1.8
INT u_egpMaxNeighbors	1.3.6.1.4.1.16.2.1.8.1	INTEGER	read-only
INT u_egpNumberTrustedNeighbors	1.3.6.1.4.1.16.2.1.8.2	INTEGER	read-write
INT u_egpNumberNeighbors	1.3.6.1.4.1.16.2.1.8.3	INTEGER	read-write
u_egpNeighborTable	1.3.6.1.4.1.16.2.1.8.4		read-write
u_egpNeighborEntry	1.3.6.1.4.1.16.2.1.8.4.1		read-write
IP u_egpNeighbor	1.3.6.1.4.1.16.2.1.8.4.1.1	IpAddress	read-write
INT u_egpAutoSysNumber	1.3.6.1.4.1.16.2.1.8.5	INTEGER	read-write
INT u_egpMinHelloInterval	1.3.6.1.4.1.16.2.1.8.6	INTEGER	read-write
INT u_egpMinPollInterval	1.3.6.1.4.1.16.2.1.8.7	INTEGER	read-write
INT u_egpRequestCeaseInterval	1.3.6.1.4.1.16.2.1.8.8	INTEGER	read-write
INT u_egpDeclareDownInterval	1.3.6.1.4.1.16.2.1.8.9	INTEGER	read-write
INT u_egpAcquireCeaseInterval	1.3.6.1.4.1.16.2.1.8.10	INTEGER	read-write
INT u_egpEnoughInterval	1.3.6.1.4.1.16.2.1.8.11	INTEGER	read-write
INT u_egpPurgeInterval	1.3.6.1.4.1.16.2.1.8.12	INTEGER	read-write
INT u_egpMode	1.3.6.1.4.1.16.2.1.8.13	INTEGER	read-write
INT u_egpErrorTreatment	1.3.6.1.4.1.16.2.1.8.14	INTEGER	read-write
IP u_egpSharedNetwork	1.3.6.1.4.1.16.2.1.8.15	IpAddress	read-write
u_ggp	1.3.6.1.4.1.16.2.1.12
INT u_ggpEchoInterval	1.3.6.1.4.1.16.2.1.12.1	INTEGER	read-write
INT u_ggpMaxNeighbors	1.3.6.1.4.1.16.2.1.12.2	INTEGER	read-only
INT u_ggpNumberNeighbors	1.3.6.1.4.1.16.2.1.12.3	INTEGER	read-only
u_ggpNeighborTable	1.3.6.1.4.1.16.2.1.12.4		read-write
u_ggpNeighborEntry	1.3.6.1.4.1.16.2.1.12.4.1		read-write
IP u_ggpNeighbor	1.3.6.1.4.1.16.2.1.12.4.1.1	IpAddress	read-write
u_rip	1.3.6.1.4.1.16.2.1.13
u_snmp	1.3.6.1.4.1.16.2.1.14
INT u_snmpVersion	1.3.6.1.4.1.16.2.1.14.1	INTEGER	read-only
OCT u_snmpCommunity	1.3.6.1.4.1.16.2.1.14.2	OCTET STRING	read-write
CTR u_snmpRequests	1.3.6.1.4.1.16.2.1.14.3	Counter	read-only
CTR u_snmpTraps	1.3.6.1.4.1.16.2.1.14.4	Counter	read-only
INT u_snmpForwardTraps	1.3.6.1.4.1.16.2.1.14.5	INTEGER	read-write
u_hfp	1.3.6.1.4.1.16.2.1.15
INT u_hfpMaxMsg	1.3.6.1.4.1.16.2.1.15.1	INTEGER	read-write
INT u_hfpPad	1.3.6.1.4.1.16.2.1.15.2	INTEGER	read-write
INT u_hfpSwap	1.3.6.1.4.1.16.2.1.15.3	INTEGER	read-write
u_ddn	1.3.6.1.4.1.16.2.1.16
INT u_ddnTimeout	1.3.6.1.4.1.16.2.1.16.1	INTEGER	read-write
INT u_ddnMsgout	1.3.6.1.4.1.16.2.1.16.2	INTEGER	read-write
INT u_ddnHipUp	1.3.6.1.4.1.16.2.1.16.3	INTEGER	read-only
INT u_ddnHdhUp	1.3.6.1.4.1.16.2.1.16.4	INTEGER	read-only
INT u_ddnLinkUp	1.3.6.1.4.1.16.2.1.16.5	INTEGER	read-only
GAU u_ddnTotalQ	1.3.6.1.4.1.16.2.1.16.6	Gauge	read-only
GAU u_ddnConnections	1.3.6.1.4.1.16.2.1.16.7	Gauge	read-only
INT u_ddnLinkDownTo	1.3.6.1.4.1.16.2.1.16.8	INTEGER	read-only
CTR u_ddnRcvIncomplete	1.3.6.1.4.1.16.2.1.16.9	Counter	read-only
CTR u_ddnConnectionsReused	1.3.6.1.4.1.16.2.1.16.10	Counter	read-only
CTR u_ddnHdhWentDown	1.3.6.1.4.1.16.2.1.16.11	Counter	read-only
CTR u_ddnLinkWentDown	1.3.6.1.4.1.16.2.1.16.12	Counter	read-only
CTR u_ddnLeaderErrs	1.3.6.1.4.1.16.2.1.16.13	Counter	read-only
CTR u_ddnPSNGoingDown	1.3.6.1.4.1.16.2.1.16.14	Counter	read-only
CTR u_ddnDeadHostSTATUS	1.3.6.1.4.1.16.2.1.16.15	Counter	read-only
CTR u_ddnIfReset	1.3.6.1.4.1.16.2.1.16.16	Counter	read-only
u_x25	1.3.6.1.4.1.16.2.1.17
u_x25IfTable	1.3.6.1.4.1.16.2.1.17.1		read-write
u_x25IfEntry	1.3.6.1.4.1.16.2.1.17.1.1		read-write
INT u_x25Service	1.3.6.1.4.1.16.2.1.17.1.1.1	INTEGER	read-write
INT u_x25Window	1.3.6.1.4.1.16.2.1.17.1.1.2	INTEGER	read-write
INT u_x25PktSize	1.3.6.1.4.1.16.2.1.17.1.1.3	INTEGER	read-write
u_fddi	1.3.6.1.4.1.16.2.1.18
u_fddiSMT	1.3.6.1.4.1.16.2.1.18.1
u_fddiSMTStationIdGrp	1.3.6.1.4.1.16.2.1.18.1.1
OCT u_fddiSMTStationId	1.3.6.1.4.1.16.2.1.18.1.1.1	OCTET STRING	read-only
INT u_fddiSMTStationType	1.3.6.1.4.1.16.2.1.18.1.1.2	INTEGER	read-only
INT u_fddiSMTVersionId	1.3.6.1.4.1.16.2.1.18.1.1.3	INTEGER	read-only
u_fddiSMTStationCfgGrp	1.3.6.1.4.1.16.2.1.18.1.2
INT u_fddiSMTMACCount	1.3.6.1.4.1.16.2.1.18.1.2.1	INTEGER	read-only
INT u_fddiSMTAttachCount	1.3.6.1.4.1.16.2.1.18.1.2.2	INTEGER	read-only
INT u_fddiSMTSpurCount	1.3.6.1.4.1.16.2.1.18.1.2.3	INTEGER	read-only
u_fddiSMTOperationalGrp	1.3.6.1.4.1.16.2.1.18.1.3
INT u_fddiSMTDasScmState	1.3.6.1.4.1.16.2.1.18.1.3.1	INTEGER	read-only
u_fddiMACTable	1.3.6.1.4.1.16.2.1.18.2
u_fddiMACEntry	1.3.6.1.4.1.16.2.1.18.2.1
u_fddiMACAddressGrp	1.3.6.1.4.1.16.2.1.18.2.1.1
OCT u_fddiMACSMTLongAddr	1.3.6.1.4.1.16.2.1.18.2.1.1.1	OCTET STRING	read-write
OCT u_fddiMACShortGrpAddr	1.3.6.1.4.1.16.2.1.18.2.1.1.2	OCTET STRING	read-write
u_fddiMACCfgGrp	1.3.6.1.4.1.16.2.1.18.2.1.2
OCT u_fddiMACUpstreamNeighbor	1.3.6.1.4.1.16.2.1.18.2.1.2.1	OCTET STRING	read-only
OCT u_fddiMACDownstreamNeighbor	1.3.6.1.4.1.16.2.1.18.2.1.2.2	OCTET STRING	read-only
INT u_fddiMACResourceIndex	1.3.6.1.4.1.16.2.1.18.2.1.2.3	INTEGER	read-only
INT u_fddiMACConnectedResId	1.3.6.1.4.1.16.2.1.18.2.1.2.4	INTEGER	read-only
u_fddiMACOperGrp	1.3.6.1.4.1.16.2.1.18.2.1.3
INT u_fddiMACTReq	1.3.6.1.4.1.16.2.1.18.2.1.3.1	INTEGER	read-write
INT u_fddiMACTMax	1.3.6.1.4.1.16.2.1.18.2.1.3.2	INTEGER	read-write
INT u_fddiMACTvxValue	1.3.6.1.4.1.16.2.1.18.2.1.3.3	INTEGER	read-write
INT u_fddiMACTMin	1.3.6.1.4.1.16.2.1.18.2.1.3.4	INTEGER	read-write
u_fddiMACCountersGrp	1.3.6.1.4.1.16.2.1.18.2.1.4
CTR u_fddiMACReceiveCt	1.3.6.1.4.1.16.2.1.18.2.1.4.1	Counter	read-only
CTR u_fddiMACTransmitCt	1.3.6.1.4.1.16.2.1.18.2.1.4.2	Counter	read-only
CTR u_fddiMACTokenCt	1.3.6.1.4.1.16.2.1.18.2.1.4.3	Counter	read-only
u_fddiMACErrorCntrsGrp	1.3.6.1.4.1.16.2.1.18.2.1.5
CTR u_fddiMACTvxExpiredCt	1.3.6.1.4.1.16.2.1.18.2.1.5.1	Counter	read-only
CTR u_fddiMACNotCopiedCt	1.3.6.1.4.1.16.2.1.18.2.1.5.2	Counter	read-only
CTR u_fddiMACLateCt	1.3.6.1.4.1.16.2.1.18.2.1.5.3	Counter	read-only
CTR u_fddiMACReceiveOverflowCt	1.3.6.1.4.1.16.2.1.18.2.1.5.4	Counter	read-only
u_fddiMACSTATUSGrp	1.3.6.1.4.1.16.2.1.18.2.1.6
CTR u_fddiMACRingOpCt	1.3.6.1.4.1.16.2.1.18.2.1.6.1	Counter	read-only
CTR u_fddiMACEnteredBeaconCt	1.3.6.1.4.1.16.2.1.18.2.1.6.2	Counter	read-only
u_fddiPHYTable	1.3.6.1.4.1.16.2.1.18.3
u_fddiPHYEntry	1.3.6.1.4.1.16.2.1.18.3.1
u_fddiPHYCfgGrp	1.3.6.1.4.1.16.2.1.18.3.1.1
INT u_fddiPHYType	1.3.6.1.4.1.16.2.1.18.3.1.1.1	INTEGER	read-only
INT u_fddiPHYConnectState	1.3.6.1.4.1.16.2.1.18.3.1.1.2	INTEGER	read-only
INT u_fddiPHYRemotePHYType	1.3.6.1.4.1.16.2.1.18.3.1.1.3	INTEGER	read-only
INT u_fddiPHYRemoteMACIndicated	1.3.6.1.4.1.16.2.1.18.3.1.1.4	INTEGER	read-only
INT u_fddiPHYResourceIndex	1.3.6.1.4.1.16.2.1.18.3.1.1.5	INTEGER	read-only
INT u_fddiPHYConnectedResId	1.3.6.1.4.1.16.2.1.18.3.1.1.6	INTEGER	read-only
INT u_fddiPHYAction	1.3.6.1.4.1.16.2.1.18.3.1.2	INTEGER	read-write
u_ip	1.3.6.1.4.1.16.2.1.19
INT u_ipLogicalDisconnect	1.3.6.1.4.1.16.2.1.19.1	INTEGER	read-write
INT u_ipLoopback	1.3.6.1.4.1.16.2.1.19.2	INTEGER	read-write
INT u_ipRedirectTo	1.3.6.1.4.1.16.2.1.19.3	INTEGER	read-write
INT u_ipMasker	1.3.6.1.4.1.16.2.1.19.4	INTEGER	read-write
IP u_ipWellKnownGateway	1.3.6.1.4.1.16.2.1.19.5	IpAddress	read-write
INT u_ipMaxRoutePids	1.3.6.1.4.1.16.2.1.19.6	INTEGER	read-only
u_ipRoutePidsTable	1.3.6.1.4.1.16.2.1.19.7		read-write
u_ipRoutePidsEntry	1.3.6.1.4.1.16.2.1.19.7.1		read-write
INT u_ipRoutePid	1.3.6.1.4.1.16.2.1.19.7.1.1	INTEGER	read-write
INT u_ipNbrStaticRoutes	1.3.6.1.4.1.16.2.1.19.8	INTEGER	read-only
u_ipStaticRouteTable	1.3.6.1.4.1.16.2.1.19.9		read-write
u_ipStaticRouteEntry	1.3.6.1.4.1.16.2.1.19.9.1		read-write
IP u_ipStaticRouteNetwork	1.3.6.1.4.1.16.2.1.19.9.1.1	IpAddress	read-only
IP u_ipStaticRouteGateway	1.3.6.1.4.1.16.2.1.19.9.1.2	IpAddress	read-write
INT u_ipStaticRouteCost	1.3.6.1.4.1.16.2.1.19.9.1.3	INTEGER	read-write
INT u_ipStaticRouteOverride	1.3.6.1.4.1.16.2.1.19.9.1.4	INTEGER	read-write
u_ipRemotegTable	1.3.6.1.4.1.16.2.1.19.10		read-write
u_ipRemotegEntry	1.3.6.1.4.1.16.2.1.19.10.1		read-write
INT u_ipRemoteg	1.3.6.1.4.1.16.2.1.19.10.1.1	INTEGER	read-write
u_ipNetMaxPktTable	1.3.6.1.4.1.16.2.1.19.11		read-write
u_ipNetMaxPktEntry	1.3.6.1.4.1.16.2.1.19.11.1		read-write
INT u_ipNetMaxPkt	1.3.6.1.4.1.16.2.1.19.11.1.1	INTEGER	read-write

RFC description

Unisys enterprise MIB with interfaces, TCP/IP, FDDI, and network protocol management objects.

Start monitoring Unisys network router/gateway, legacy early 1990s (interface/IP/TCP/FDDI/X.25 protocol status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UNISYS-MIB

What Is UNISYS-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description