SONOMA-MIB

All MIBs › SONOMA-MIB

Organization: EndRun Technologies LLC

Last Updated: 2018-10-21

Category: GPS and Network Timing

Description: Manages EndRun Technologies GPS-based network timing device synchronization status and timing source configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SONOMA-MIB?

SONOMA-MIB is EndRun Technologies' enterprise MIB for their GPS/CDMA-based network timing appliances, which act as NTP (Network Time Protocol) servers synchronized to external time references. It exposes NTP client/server engine statistics such as packet counts, IRQ handling, and timing quality indicators alongside timing-source configuration. Critically for hardware/software status monitoring, it surfaces cntpTimeSinceRst (time since restart, akin to uptime), NTP packet drop/error counters, authentication failures, and time figure-of-merit values that indicate the reliability of the device's synchronized clock output. There is no explicit dependency on other MIBs beyond the standard SNMPv2 conventions, though it may be used alongside standard NTP or system MIBs for broader device health. Typical deployment is in data centers or telecom facilities requiring precise, traceable time synchronization from a GPS/CDMA-referenced appliance. Network engineers evaluating or troubleshooting this functionality can download the SONOMA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SONOMA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

EndRun Technologies GPS/CDMA network time server appliance

Monitoring Examples

An admin would poll cntpTimeFigureOfMerit and cntpLeapIndBits to confirm the device's NTP service is reporting a trustworthy, well-synchronized clock, and watch cntpAuthFail and cntpDroppedPkts/cntpIgnoredPkts for signs of misconfigured or malicious NTP clients. Tracking cntpRxPkts, cntpTxPkts, and cntpSentPktsPerSecond over time helps confirm the appliance is actively serving time to its client population without overload, while a sudden change in cntpTimeSinceRst signals an unexpected reboot. A rising cntpUnSentPkts count could reveal the device failing to respond to NTP requests fast enough, indicating a software or resource issue.

What Can Be Monitored

time since last restart (uptime)
NTP packets received/transmitted/sent per second
dropped, ignored, and unsent packet counts
authentication failures
time figure-of-merit (clock quality)
leap indicator bits

Imported Objects

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
enterprises

From SNMPv2-TC

DisplayString

How to Use in IPNetwork Monitor

Example using cntpTimeSinceRst OID:

Select an EndRun Technologies GPS/CDMA network time server appliance (NTP engine/timing-quality status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cntpTimeSinceRst into the Find box to locate it in the OID tree, then select it and click OK. It reports the time since NTP daemon restart. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
endRunTechnologiesMIB	1.3.6.1.4.1.13827
endRunTechnologies	1.3.6.1.4.1.13827.0			EndRun Technologies Enterprise MIB
sonomaCDMA	1.3.6.1.4.1.13827.11
cntp	1.3.6.1.4.1.13827.11.1
cntptrap	1.3.6.1.4.1.13827.11.1.0
NTF cntpTrapLeapIndBitsChange	1.3.6.1.4.1.13827.11.1.0.1			A cntpTrapNTPLeapIndBitsChange trap signifies that the value of the leap indicator bits contained in the NTP reply packets sent by the time server has changed. The current value of these bits is contained in the included cntpLeapIndBits. The decimal value of these bits ranges from 0 to 3: 0 is the no fault, no leap warning condition 1 is the no fault, leap second insertion warning condition 2 is the no fault, leap second deletion warning condition 3 is the unsynchronized, alarm condition
NTF cntpTrapStratumChange	1.3.6.1.4.1.13827.11.1.0.2			A cntpTrapStratumChange trap signifies that the value of the stratum field contained in the NTP reply packets sent by the time server has changed. The current value is contained in the included variable, cntpStratum. The decimal value of this field ranges from 1 to 16: 1 is the synchronized, actively locked to the reference UTC source stratum 2 is the synchronized, actively locked to a network stratum 1 server stratum 16 is the unsynchronized stratum level
C32 cntpTimeSinceRstEx	1.3.6.1.4.1.13827.11.1.1	Counter32	read-only	Time since NTP daemon restart.
C32 cntpIRQsHandled	1.3.6.1.4.1.13827.11.1.2	Counter32	read-only	Total number of Interrupts handled by the NTP daemon.
C32 cntpRxPkts	1.3.6.1.4.1.13827.11.1.3	Counter32	read-only	Total number of NTP request packets received by the NTP daemon.
C32 cntpRxPktsByIRQ	1.3.6.1.4.1.13827.11.1.4	Counter32	read-only	Total number of NTP request packets received via IRQ by the NTP daemon.
C32 cntpTxPkts	1.3.6.1.4.1.13827.11.1.5	Counter32	read-only	Total number of NTP reply packets transmitted by the NTP daemon.
INT cntpSentPktsPerSecond	1.3.6.1.4.1.13827.11.1.6	INTEGER	read-only	NTP reply packets sent per second by the NTP daemon.
C32 cntpUnSentPkts	1.3.6.1.4.1.13827.11.1.7	Counter32	read-only	Total number of NTP reply packets unsent by the NTP daemon.
C32 cntpIgnoredPkts	1.3.6.1.4.1.13827.11.1.8	Counter32	read-only	Total number of NTP request packets ignored by the NTP daemon.
C32 cntpDroppedPkts	1.3.6.1.4.1.13827.11.1.9	Counter32	read-only	Total number of NTP request packets dropped by the NTP daemon.
C32 cntpAuthFail	1.3.6.1.4.1.13827.11.1.10	Counter32	read-only	Total number of authentication failures detected by the NTP daemon.
INT cntpTimeFigureOfMerit	1.3.6.1.4.1.13827.11.1.11	INTEGER	read-only	The Time Figure of Merit (TFOM) value ranges from 6 to 9 and indicates the current estimate of the worst case time error. It is a logarithmic scale, with each increment indicating a tenfold increase in the worst case time error boundaries. The scale is referenced to a worst case time error of 100 picoseconds, equivalent to a TFOM of zero. During normal locked operation with CDMA the TFOM is 6 and implies a worst case time error of 100 microseconds. During periods of signal loss, the CDMA sub-system will compute an extrapolated worst case time error. One hour after the worst case time error has reached the value equivalent to a TFOM of TFOM Fault Level, the NTP server will cease to send stratum 1 reply packets and an Alarm LED will be energized.
INT cntpLeapIndBits	1.3.6.1.4.1.13827.11.1.12	INTEGER	read-only	This is a status code indicating: normal operation, a leap second to be inserted in the last minute of the current day, a leap second to be deleted in the last second of the day or an alarm condition indicating loss of timing synchronization. The leap indicator field of NTP reply packets sent from this server is set to cntpLeapIndBits.
STR cntpSyncSource	1.3.6.1.4.1.13827.11.1.13	DisplayString	read-only	This is an ASCII string identifying the synchronization source for this NTP server. It is one of CDMA, an IP address of a stratum 1 server, or NONE. If it is NONE, then the server is not synchronized, has its Leap Indicator Bits in the Alarm state and is running at Stratum 16. If it is an IP address, then the server is operating as a stratum 2 server synchronized to the network connected stratum 1 server whose IP address is shown. Check the Stratum, Leap Indicator Bits and Time Figure of Merit for further information. NTP reply packets from this server will have the reference identifier field set to cntpSyncSource if it is CDMA. Otherwise it will be set to either an IP address or 0.0.0.0 (NONE).
STR cntpOffsetToCDMAReference	1.3.6.1.4.1.13827.11.1.14	DisplayString	read-only	This is an ASCII string containing the floating value of the current offset in units of seconds of the NTP server CPU clock to the CDMA reference time. Positive values imply that the NTP server clock is ahead of the CDMA reference time.
INT cntpStratum	1.3.6.1.4.1.13827.11.1.15	INTEGER	read-only	This is an integer showing the current stratum level being reported by the NTP daemon in its reply packets to clients. If it is 1, then the server is fully synchronized and delivering Stratum 1 accuracy. If it is greater than 1 and less than 16, it is synchronized to a network connected NTP server operating at one stratum lower. If it is 16, then the server is unambiguously unsynchronized. NTP clients on the network should be configured to not use the time from this server if the stratum is 16.
STR cntpVersion	1.3.6.1.4.1.13827.11.1.16	DisplayString	read-only	This is an ASCII string showing the system root file system firmware version.
STR cntpKernelVersion	1.3.6.1.4.1.13827.11.1.17	DisplayString	read-only	This is an ASCII string showing the system Linux kernel firmware version.
STR cntpOscType	1.3.6.1.4.1.13827.11.1.18	DisplayString	read-only	This is an ASCII string showing the installed oscillator type. It is one of TCXO, OCXO, or Rubidium.
STR cntpTimeMode	1.3.6.1.4.1.13827.11.1.19	DisplayString	read-only	This is an ASCII string showing the time mode of operation for any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It DOES NOT indicate the time mode of the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It can be LOCAL_AUTO, LOCAL_MANUAL, GPS or UTC. In LOCAL_AUTO mode, the local offset to UTC is automatically determined from the CDMA transmissions received from the base station. In LOCAL_MANUAL mode, the local offset to UTC is user programmed and overrides the CDMA system data.
INT cntpLocalOffset	1.3.6.1.4.1.13827.11.1.20	INTEGER	read-only	This value is the local time offset configured for any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL or LOCAL_AUTO. It DOES NOT indicate the local time offset of the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. When cntpTimeMode is set to LOCAL_AUTO, cntpLocalOffset is determined from the CDMA base station. When cntpTimeMode is set to LOCAL_MANUAL, cntpLocalOffset is the user configured value. Its units are half-hours, ranging from -25 to 25, where negative values imply that the local time is behind UTC.
INT cntpDSTStartMonth	1.3.6.1.4.1.13827.11.1.21	INTEGER	read-only	This value is the month that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT cntpDSTStartSunday	1.3.6.1.4.1.13827.11.1.22	INTEGER	read-only	This value is the Sunday of the month that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT cntpDSTStartHour	1.3.6.1.4.1.13827.11.1.23	INTEGER	read-only	This value is the hour that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It ranges from 0 to 23, where 0 is midnight.
INT cntpDSTStopMonth	1.3.6.1.4.1.13827.11.1.24	INTEGER	read-only	This value is the month that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT cntpDSTStopSunday	1.3.6.1.4.1.13827.11.1.25	INTEGER	read-only	This value is the Sunday of the month that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT cntpDSTStopHour	1.3.6.1.4.1.13827.11.1.26	INTEGER	read-only	This value is the hour that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when cntpTimeMode is set to LOCAL_MANUAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It ranges from 0 to 23, where 0 is midnight.
STR cntpCPUDieTemperature	1.3.6.1.4.1.13827.11.1.27	DisplayString	read-only	ASCII string representing the current CPU internal die temperature, in units of Celsius degrees in floating point notation.
INT cntpCPUFreeMemory	1.3.6.1.4.1.13827.11.1.28	INTEGER	read-only	This value is the CPU Free Memory in kiloBytes.
INT cntpCPULoadAveragePerCent	1.3.6.1.4.1.13827.11.1.29	INTEGER	read-only	This value is the CPU Load Average as percent of total load.
cdma	1.3.6.1.4.1.13827.11.2
cdmatrap	1.3.6.1.4.1.13827.11.2.0
NTF cdmaTrapFaultStatusChange	1.3.6.1.4.1.13827.11.2.0.1			A cdmaTrapFaultStatusChange trap signifies that the value of the least significant two nibbles of the fault status word reported by the CDMA sub-system has changed. The current value is contained in the included cdmaFaultStatus.
NTF cdmaTrapFault2StatusChange	1.3.6.1.4.1.13827.11.2.0.2			A cdmaTrapFault2StatusChange trap signifies that the value of the most significant two nibbles of the fault status word reported by the CDMA sub-system has changed. The current value is contained in the included cdmaFault2Status.
NTF cdmaTrapTimeFigureOfMeritChange	1.3.6.1.4.1.13827.11.2.0.3			A cdmaTrapTimeFigureOfMeritChange trap signifies that the value of the TFOM reported by the CDMA sub-system has changed. The current value is contained in the included cdmaTimeFigureOfMerit.
BIT cdmaFaultStatus	1.3.6.1.4.1.13827.11.2.1	Bits	read-only	This is a bit string contained in one character representing the least significant two nibbles of the CDMA subsystem fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 7: DAC controlling the system Oscillator is near the high or low limit. Bit 6: Time Figure of Merit has been >= TFOM Fault Level for 1 hour. Bit 5: Field Programmable Gate Array (FPGA) did not configure properly. Bit 4: FLASH memory had a write fault. Bit 3: CDMA Receiver Communication fault. Bit 2: CDMA reference time fault (fails sanity checks). Bit 1: NTP daemon is not polling the CDMA reference clock. Bit 0: CDMA Receiver Fault, see cdmaReceiverFaultStatus for details. ATTENTION: This object is deprecated for use in snmpget queries due to a defect in reporting for one specific combination of bits. It remains in this MIB for use with the cdmaTrapFaultStatusChange object, where it reports accurately. Use the new cdmaFaultNibble0Status and cdmaFaultNibble1Status objects for querying via snmpget.
BIT cdmaFault2Status	1.3.6.1.4.1.13827.11.2.2	Bits	read-only	This is a bit string contained in one character representing the most significant two nibbles of the CDMA fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 7: Primary Redundant Power Supply is Faulting. Bit 6: Secondary Redundant Power Supply is Faulting. Bit 5: Oscillator PLL Faulting. Bit 4: Not Used. Bit 3: Not Used. Bit 2: Not Used. Bit 1: Not Used. Bit 0: Installed System Power exceeds maximum. ATTENTION: This object is deprecated for use in snmpget queries due to a defect in reporting for one specific combination of bits. It remains in this MIB for use with the cdmaTrapFault2StatusChange object, where it reports accurately. Use the new cdmaFaultNibble2Status and cdmaFaultNibble3Status objects for querying via snmpget.
BIT cdmaReceiverFaultNibble0Status	1.3.6.1.4.1.13827.11.2.3	Bits	read-only	This is a bit string contained in one character representing the least significant nibble of the CDMA receiver fault status byte. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: CDMA Receiver Main Oscillator Frequency Control DAC near high or low limit. Bit 2: Time Figure of Merit has been >= TFOM Fault Level for 1 hour. Bit 1: Field Programmable Gate Array (FPGA) Configuration Fault. Bit 0: FLASH Memory Write Fault.
BIT cdmaReceiverFaultNibble1Status	1.3.6.1.4.1.13827.11.2.4	Bits	read-only	This is a bit string contained in one character representing the most significant nibble of the CDMA receiver fault status byte. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: CDMA Receiver Local Oscillator Synthesizer Fault. Bit 2: CDMA Receiver Local Oscillator Synthesizer Near Tuning Limit. Bit 1: CDMA Decoded Time Jump. Bit 0: CDMA Receiver Main Oscillator Fault.
INT cdmaTimeFigureOfMerit	1.3.6.1.4.1.13827.11.2.5	INTEGER	read-only	The Time Figure of Merit (TFOM) value ranges from 6 to 9 and indicates the current estimate of the worst case time error. It is a logarithmic scale, with each increment indicating a tenfold increase in the worst case time error boundaries. The scale is referenced to a worst case time error of 100 picoseconds, equivalent to a TFOM of zero. During normal locked operation the TFOM is 6 and implies a worst case time error of 100 microseconds. During periods of signal loss, the CDMA sub-system will compute an extrapolated worst case time error. One hour after the worst case time error has reached the value equivalent to a TFOM of TFOM Fault Level, the NTP server will cease to send stratum 1 reply packets and an Alarm LED will be energized.
STR cdmaSigProcState	1.3.6.1.4.1.13827.11.2.6	DisplayString	read-only	Current CDMA receiver subsytem state. One of WRM, ACQ, LKG or LKD with WRM indicating either an OCXO or Rubidium is warming up, ACQ indicating the acquisition state and LKD the fully locked on state. This is the status of the lock of the main system timing signals to the CDMA Receiver.
STR cdmaReceiverSigProcState	1.3.6.1.4.1.13827.11.2.7	DisplayString	read-only	Current CDMA Receiver signal processor state. One of ACQ, DET, LKG, TKG or LKD with ACQ indicating the acquisition state and LKD the fully locked on state.
STR cdmaChannel	1.3.6.1.4.1.13827.11.2.8	DisplayString	read-only	Current CDMA channelset, or frequency band, and specific channel being used. The first field indicates the channelset or band: NAC (North American Cellular), NAP (North American PCS), SKC (South Korean Cellular), IND (Indian Cellular) or JC (Japanese Cellular). The specific channel within the channelset is indicated in the next field, and the last field indicates the service provider. This field is not always meaningful. An example channel might be NAP_01_A which indicates channel 1 in service provider A's group of channels in the North American PCS channelset.
INT cdmaPNO	1.3.6.1.4.1.13827.11.2.9	INTEGER	read-only	Current Pseudo Noise Offset of the base station being tracked. The value ranges from 0 to 511 and is in units of 64 Pseudo Noise Code chips. This offset serves as a base station identifier that is analogous to the Pseudo Random Noise (PRN) codes used by the individual satellites in the GPS system.
INT cdmaAGC	1.3.6.1.4.1.13827.11.2.10	INTEGER	read-only	Current 8 bit, Automatic Gain Control (AGC) DAC value. Typical values are around 200, but proximity to the base station, type of building construction and orientation within the building have a strong influence on this value. More positive values have the effect of increasing the RF gain.
INT cdmaReceiverVCDAC	1.3.6.1.4.1.13827.11.2.11	INTEGER	read-only	Current CDMA Receiver 16 bit, Voltage Controlled TCXO DAC value. Typical range is 20000 to 40000, where more positive numbers have the effect of raising the oscillator frequency. This is not the DAC controlling the main system oscillator.
STR cdmaCarrierToNoiseRatio	1.3.6.1.4.1.13827.11.2.12	DisplayString	read-only	ASCII string representing the current received CDMA signal carrier-to-noise ratio, a unitless quantity. Numbers less than 2.5 indicate a very weak signal condition.
STR cdmaFrameErrorRate	1.3.6.1.4.1.13827.11.2.13	DisplayString	read-only	ASCII string representing the current sync channel message error rate, a number ranging from 0.000 to 1.000. It indicates the proportion of messages received that fail the Cyclical Redundancy Check.
STR cdmaLeapMode	1.3.6.1.4.1.13827.11.2.14	DisplayString	read-only	ASCII string showing the current leap second mode of operation for the CDMA sub-system. It is either AUTO or USER. If the mode is USER, then the current and future values of the UTC to GPS leap second offset is also included.
INT cdmaUserCurrentLeapSeconds	1.3.6.1.4.1.13827.11.2.15	INTEGER	read-only	This value is the user-entered current difference in seconds between GPS time and UTC time. GPS time is ahead of UTC time by this amount.
INT cdmaUserFutureLeapSeconds	1.3.6.1.4.1.13827.11.2.16	INTEGER	read-only	This value is the user-entered future difference in seconds between GPS time and UTC time. Leap seconds may be inserted or deleted from the UTC timescale twice during the year: Dec 31 and June 30 at UTC midnight. If this value is the same as cdmaUserCurrentLeapSeconds, then no leap second insertion or deletion will occur at the next possible time. If it is different, then the change will take affect at the next possible time. On the day of a scheduled leap insertion or deletion event, the value in cdmaUserFutureLeapSeconds will be transferred to cdmaFutureLeapSeconds, which will set in motion the leap second insert/delete process. that will advance or retard the system clock so that GPS time will be ahead of UTC time by this amount.
INT cdmaCurrentLeapSeconds	1.3.6.1.4.1.13827.11.2.17	INTEGER	read-only	This value is the active current difference in seconds between GPS time and UTC time. GPS time is ahead of UTC time by this amount.
INT cdmaFutureLeapSeconds	1.3.6.1.4.1.13827.11.2.18	INTEGER	read-only	This value is the active future difference in seconds between GPS time and UTC time. Leap seconds may be inserted or deleted from the UTC timescale twice during the year: Dec 31 and June 30 at UTC midnight. If this value is the same as cdmaCurrentLeapSeconds on Dec 31 or June 30, then no leap second insertion or deletion will occur. If it is different, then the change will take affect at UTC midnight. GPS time will then be ahead of UTC time by this amount.
STR cdmaVersion	1.3.6.1.4.1.13827.11.2.19	DisplayString	read-only	ASCII string showing the CDMA sub-system firmware and FPGA versions.
STR cdmaReceiverVersion	1.3.6.1.4.1.13827.11.2.20	DisplayString	read-only	ASCII string showing the CDMA receiver firmware and FPGA versions.
INT cdmaCalibrationDelay	1.3.6.1.4.1.13827.11.2.21	INTEGER	read-only	Signed integer representing the current calibration delay being applied to the timing outputs, in units of nanoseconds. Positive values indicate that the timing outputs are advanced.
INT cdmaCoastDuration	1.3.6.1.4.1.13827.11.2.22	INTEGER	read-only	Unsigned integer representing the current elapsed time since the unit lost CDMA reception in units of seconds.
STR cdmaEstimatedTimeError	1.3.6.1.4.1.13827.11.2.23	DisplayString	read-only	ASCII string representing the magnitude of the estimated time error since the unit lost CDMA reception, in units of seconds in scientific floating point notation. While locked, the value is the magnitude of the measured time error relative to CDMA.
STR cdmaMeasuredTimeError	1.3.6.1.4.1.13827.11.2.24	DisplayString	read-only	ASCII string representing the measured time error of the timing outputs relative to CDMA, in units of seconds in scientific floating point notation. While coasting, the value is the last measured value prior to losing CDMA reception.
STR cdmaMeasurementTimeDeviation	1.3.6.1.4.1.13827.11.2.25	DisplayString	read-only	ASCII string representing the time deviation (TDEV) of the CDMA measurement data, in units of seconds in scientific floating point notation. While coasting, the value is the last computed value prior to losing CDMA reception.
INT cdmaSystemOSCDAC	1.3.6.1.4.1.13827.11.2.26	INTEGER	read-only	Current system 20 bit, Voltage Controlled TCXO DAC value. Typical range is 320000 to 640000, where more positive numbers have the effect of raising the oscillator frequency. This is the DAC controlling the main system oscillator.
STR cdmaMeasuredOscillatorAgeing	1.3.6.1.4.1.13827.11.2.27	DisplayString	read-only	ASCII string representing the ageing rate per day of the installed osc- illator, in scientific floating point notation. It is computed via linear regression and requires several hours following initial lock to CDMA to see the first update. While coasting, the value is the last computed value prior to losing CDMA reception.
STR cdmaControlLoopTimeConstant	1.3.6.1.4.1.13827.11.2.28	DisplayString	read-only	ASCII string representing the current equivalent averaging time of the oscillator control loop, in units of seconds in floating point notation. The value is dynamically updated based on the stability of the oscillator.
STR cdmaInternalTemperature	1.3.6.1.4.1.13827.11.2.29	DisplayString	read-only	ASCII string representing the current internal chassis temperature, in units of Celsius degrees in floating point notation. A value is only available when the installed oscillator is an OCXO or Rubidium.
STR cdmaSignalLossFaultMask	1.3.6.1.4.1.13827.11.2.30	DisplayString	read-only	The CDMA signal loss fault mask is either on or off. When it is off, the server will set the Signal Loss Fault Bit in the Fault Status Byte one hour after TFOM reaches the TFOM Fault Level. When the setting is on, the server will not set the Signal Loss Fault Bit in the Fault Status Byte one hour or more after TFOM reaches TFOM Fault level.
STR cdmaPrimaryPowerFaultAlarmMask	1.3.6.1.4.1.13827.11.2.31	DisplayString	read-only	The Primary Power input fault alarm mask is either on or off. When it is on, the server will not assert an Alarm condition on a fault in the Primary Power supply. Unlike other fault masks, the fault condition will continue to be visible in the Fault Status Byte. This mask capability is useful when performing system tests when only a single power input is available and an alarm would be undesirable. When the setting is off, the server will assert an Alarm condition in addition to setting the appropriate bit in the Fault Status Byte.
STR cdmaSecondaryPowerFaultAlarmMask	1.3.6.1.4.1.13827.11.2.32	DisplayString	read-only	The Secondary Power input fault alarm mask is either on or off. When it is on, the server will not assert an Alarm condition on a fault in the Secondary Power supply. Unlike other fault masks, the fault condition will continue to be visible in the Fault Status Byte. This mask capability is useful when performing system tests when only a single power input is available and an alarm would be undesirable. When the setting is off, the server will assert an Alarm condition in addition to setting the appropriate bit in the Fault Status Byte.
BIT cdmaFaultNibble0Status	1.3.6.1.4.1.13827.11.2.33	Bits	read-only	This is a bit string contained in one character representing the least significant nibble of the CDMA subsystem fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: DAC controlling the system Oscillator is near the high or low limit. Bit 2: Time Figure of Merit has been >= TFOM Fault Level for 1 hour. Bit 1: Field Programmable Gate Array (FPGA) did not configure properly. Bit 0: FLASH memory had a write fault.
BIT cdmaFaultNibble1Status	1.3.6.1.4.1.13827.11.2.34	Bits	read-only	This is a bit string contained in one character representing the second nibble of the CDMA subsystem fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: CDMA Receiver Communication fault. Bit 2: CDMA reference time fault (fails sanity checks). Bit 1: NTP daemon is not polling the CDMA reference clock. Bit 0: CDMA Receiver Fault, see cdmaReceiverFaultStatus for details.
BIT cdmaFaultNibble2Status	1.3.6.1.4.1.13827.11.2.35	Bits	read-only	This is a bit string contained in one character representing the third nibble of the CDMA fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: Primary Redundant Power Supply is Faulting. Bit 2: Secondary Redundant Power Supply is Faulting. Bit 1: Oscillator PLL Faulting. Bit 0: Not Used.
BIT cdmaFaultNibble3Status	1.3.6.1.4.1.13827.11.2.36	Bits	read-only	This is a bit string contained in one character representing the most significant nibble of the CDMA fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the cdmastat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: Not Used. Bit 2: Not Used. Bit 1: Not Used. Bit 0: Installed System Power exceeds maximum.
cCPUIO	1.3.6.1.4.1.13827.11.3
STR csysio1PPSWidth	1.3.6.1.4.1.13827.11.3.1	DisplayString	read-only	ASCII string showing the status of the Settable PulseWidth, 1PPS Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing the current pulsewidth setting.
STR csysioTimeCodeFormat	1.3.6.1.4.1.13827.11.3.2	DisplayString	read-only	ASCII string showing the status of the Selectable Format, Time Code Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing the current time code output format setting.
INT csysioSynthesizerHz	1.3.6.1.4.1.13827.11.3.3	INTEGER	read-only	Integer showing the current frequency setting of the 1 Hz resolution, Direct Digital Synthesizer (DDS) Output, system-wide I/O signal. If this option is not installed the value is -1, otherwise the value ranges from 0 to 10000000 Hz.
STR csysioSerialTimeOutputBaudrate	1.3.6.1.4.1.13827.11.3.4	DisplayString	read-only	ASCII string showing the Baudrate of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of 4800, 9600, 19200 or 57600.
STR csysioSerialTimeOutputFormat	1.3.6.1.4.1.13827.11.3.5	DisplayString	read-only	ASCII string showing the Format of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of SYSPLEX, TRUETIME, NENA0, NENA1, NENA8, ENDRUN, ENDRUNX or NMEA.
STR csysioSerialTimeOutputParity	1.3.6.1.4.1.13827.11.3.6	DisplayString	read-only	ASCII string showing the Parity of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of ODD, EVEN or NONE.
STR csysioSerialTimeNMEASentence1	1.3.6.1.4.1.13827.11.3.7	DisplayString	read-only	ASCII string showing the first NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE. At this time, only the ZDA sentence is active from the CDMA products.
STR csysioSerialTimeNMEASentence2	1.3.6.1.4.1.13827.11.3.8	DisplayString	read-only	ASCII string showing the second NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE. At this time, only the ZDA sentence is active from the CDMA products.
STR csysioSerialTimeNMEASentence3	1.3.6.1.4.1.13827.11.3.9	DisplayString	read-only	ASCII string showing the third NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE. At this time, only the ZDA sentence is active from the CDMA products.
STR ccpuioConnA	1.3.6.1.4.1.13827.11.3.10	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector A. It may be NOT INSTALLED, or a string showing the current I/O selection.
STR ccpuioConnB	1.3.6.1.4.1.13827.11.3.11	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector B. It may be NOT INSTALLED, or a string showing the current I/O selection.
STR ccpuioConnC	1.3.6.1.4.1.13827.11.3.12	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector C. It may be NOT INSTALLED, or a string showing the current I/O selection.
cptp0	1.3.6.1.4.1.13827.11.4
INT cptp0Version	1.3.6.1.4.1.13827.11.4.1	INTEGER	read-only	This value is the Version of the Precise Time Protocol, which is 2.
INT cptp0SyncInterval	1.3.6.1.4.1.13827.11.4.2	INTEGER	read-only	This value is the log base 2 of the PTP Sync Interval in seconds. Values range from -7 to 0, which covers the range from 1/128 to 1 second.
INT cptp0AnnounceInterval	1.3.6.1.4.1.13827.11.4.3	INTEGER	read-only	This value is the log base 2 of the PTP Announce Interval in seconds. Values range from 0 to 4, which covers the range from 1 to 16 seconds.
INT cptp0Priority1	1.3.6.1.4.1.13827.11.4.4	INTEGER	read-only	This value is the PTP Priority1 parameter. It ranges from 0 to 255.
INT cptp0Priority2	1.3.6.1.4.1.13827.11.4.5	INTEGER	read-only	This value is the PTP Priority2 parameter. It ranges from 0 to 255.
INT cptp0DelayMechanism	1.3.6.1.4.1.13827.11.4.6	INTEGER	read-only	This value maps to the PTP Delay Mechanism, one of E2E, P2P or disabled.
INT cptp0Domain	1.3.6.1.4.1.13827.11.4.7	INTEGER	read-only	This value is the PTP Domain parameter. It ranges from 0 to 255.
INT cptp0TimeMode	1.3.6.1.4.1.13827.11.4.8	INTEGER	read-only	This value maps to the PTP Time Mode, one of UTC or PTP.
INT cptp0TTL	1.3.6.1.4.1.13827.11.4.9	INTEGER	read-only	This value is the PTP multicast Time-To-Live parameter. It ranges from 1 to 255.
INT cptp0ClockClass	1.3.6.1.4.1.13827.11.4.10	INTEGER	read-only	This value maps to the PTP Clock Class, one of Locked, Holdover or Unlocked on either the PTP or arbitrary, i.e. UTC time scale.
INT cptp0TimeScale	1.3.6.1.4.1.13827.11.4.11	INTEGER	read-only	This value maps to the PTP Time Scale, one of ARB or PTP. When operating in other than PTP Time Mode, this value is always ARB, arbitrary.
INT cptp0PortState	1.3.6.1.4.1.13827.11.4.12	INTEGER	read-only	This value maps to the PTP Port State, one of Initializing, Faulty, Disabled, Listening, PreMaster, Master, Passive, Uncalibrated or Slave.
INT cptp0TimeSource	1.3.6.1.4.1.13827.11.4.13	INTEGER	read-only	This value maps to the PTP Time Source, one of Atom, GPS, Radio, PTP, NTP, Hand, Other or Oscillator.
INT cptp0UTCOffset	1.3.6.1.4.1.13827.11.4.14	INTEGER	read-only	This value is the UTC offset from Atomic Time in seconds. It is currently 35 seconds.
INT cptp0UTCOffsetValid	1.3.6.1.4.1.13827.11.4.15	INTEGER	read-only	This value maps to the validity of the UTC offset from Atomic Time in seconds. It is either False or True.
INT cptp0ClockAccuracy	1.3.6.1.4.1.13827.11.4.16	INTEGER	read-only	This value maps to the PTP Clock Accuracy, with values ranging from 25 nanoseconds to Unknown.
INT cptp0Leap59	1.3.6.1.4.1.13827.11.4.17	INTEGER	read-only	This value maps to the state of the Leap 59 second indicator, which when True, indicates that a UTC leap second deletion event is imminent. It is either False or True.
INT cptp0Leap61	1.3.6.1.4.1.13827.11.4.18	INTEGER	read-only	This value maps to the state of the Leap 61 second indicator, which when True, indicates that a UTC leap second insertion event is imminent. It is either False or True.
INT cptp0TimeTraceable	1.3.6.1.4.1.13827.11.4.19	INTEGER	read-only	This value maps to the state of the PTP Time Traceable indicator, which when True, indicates that the time of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
INT cptp0FreqTraceable	1.3.6.1.4.1.13827.11.4.20	INTEGER	read-only	This value maps to the state of the PTP Frequency Traceable indicator, which when True, indicates that the frequency of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
cptp1	1.3.6.1.4.1.13827.11.5
INT cptp1Version	1.3.6.1.4.1.13827.11.5.1	INTEGER	read-only	This value is the Version of the Precise Time Protocol, which is 2.
INT cptp1SyncInterval	1.3.6.1.4.1.13827.11.5.2	INTEGER	read-only	This value is the log base 2 of the PTP Sync Interval in seconds. Values range from -7 to 0, which covers the range from 1/128 to 1 second.
INT cptp1AnnounceInterval	1.3.6.1.4.1.13827.11.5.3	INTEGER	read-only	This value is the log base 2 of the PTP Announce Interval in seconds. Values range from 0 to 4, which covers the range from 1 to 16 seconds.
INT cptp1Priority1	1.3.6.1.4.1.13827.11.5.4	INTEGER	read-only	This value is the PTP Priority1 parameter. It ranges from 0 to 255.
INT cptp1Priority2	1.3.6.1.4.1.13827.11.5.5	INTEGER	read-only	This value is the PTP Priority2 parameter. It ranges from 0 to 255.
INT cptp1DelayMechanism	1.3.6.1.4.1.13827.11.5.6	INTEGER	read-only	This value maps to the PTP Delay Mechanism, one of E2E, P2P or disabled.
INT cptp1Domain	1.3.6.1.4.1.13827.11.5.7	INTEGER	read-only	This value is the PTP Domain parameter. It ranges from 0 to 255.
INT cptp1TimeMode	1.3.6.1.4.1.13827.11.5.8	INTEGER	read-only	This value maps to the PTP Time Mode, one of UTC or PTP.
INT cptp1TTL	1.3.6.1.4.1.13827.11.5.9	INTEGER	read-only	This value is the PTP multicast Time-To-Live parameter. It ranges from 1 to 255.
INT cptp1ClockClass	1.3.6.1.4.1.13827.11.5.10	INTEGER	read-only	This value maps to the PTP Clock Class, one of Locked, Holdover or Unlocked on either the PTP or arbitrary, i.e. UTC time scale.
INT cptp1TimeScale	1.3.6.1.4.1.13827.11.5.11	INTEGER	read-only	This value maps to the PTP Time Scale, one of ARB or PTP. When operating in other than PTP Time Mode, this value is always ARB, arbitrary.
INT cptp1PortState	1.3.6.1.4.1.13827.11.5.12	INTEGER	read-only	This value maps to the PTP Port State, one of Initializing, Faulty, Disabled, Listening, PreMaster, Master, Passive, Uncalibrated or Slave.
INT cptp1TimeSource	1.3.6.1.4.1.13827.11.5.13	INTEGER	read-only	This value maps to the PTP Time Source, one of Atom, GPS, Radio, PTP, NTP, Hand, Other or Oscillator.
INT cptp1UTCOffset	1.3.6.1.4.1.13827.11.5.14	INTEGER	read-only	This value is the UTC offset from Atomic Time in seconds. It is currently 35 seconds.
INT cptp1UTCOffsetValid	1.3.6.1.4.1.13827.11.5.15	INTEGER	read-only	This value maps to the validity of the UTC offset from Atomic Time in seconds. It is either False or True.
INT cptp1ClockAccuracy	1.3.6.1.4.1.13827.11.5.16	INTEGER	read-only	This value maps to the PTP Clock Accuracy, with values ranging from 25 nanoseconds to Unknown.
INT cptp1Leap59	1.3.6.1.4.1.13827.11.5.17	INTEGER	read-only	This value maps to the state of the Leap 59 second indicator, which when True, indicates that a UTC leap second deletion event is imminent. It is either False or True.
INT cptp1Leap61	1.3.6.1.4.1.13827.11.5.18	INTEGER	read-only	This value maps to the state of the Leap 61 second indicator, which when True, indicates that a UTC leap second insertion event is imminent. It is either False or True.
INT cptp1TimeTraceable	1.3.6.1.4.1.13827.11.5.19	INTEGER	read-only	This value maps to the state of the PTP Time Traceable indicator, which when True, indicates that the time of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
INT cptp1FreqTraceable	1.3.6.1.4.1.13827.11.5.20	INTEGER	read-only	This value maps to the state of the PTP Frequency Traceable indicator, which when True, indicates that the frequency of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
sonomaGPS	1.3.6.1.4.1.13827.12
gntp	1.3.6.1.4.1.13827.12.1
gntptrap	1.3.6.1.4.1.13827.12.1.0
NTF gntpTrapLeapIndBitsChange	1.3.6.1.4.1.13827.12.1.0.1			A gntpTrapNTPLeapIndBitsChange trap signifies that the value of the leap indicator bits contained in the NTP reply packets sent by the time server has changed. The current value of these bits is contained in the included gntpLeapIndBits. The decimal value of these bits ranges from 0 to 3: 0 is the no fault, no leap warning condition 1 is the no fault, leap second insertion warning condition 2 is the no fault, leap second deletion warning condition 3 is the unsynchronized, alarm condition
NTF gntpTrapStratumChange	1.3.6.1.4.1.13827.12.1.0.2			A gntpTrapStratumChange trap signifies that the value of the stratum field contained in the NTP reply packets sent by the time server has changed. The current value is contained in the included variable, gntpStratum. The decimal value of this field ranges from 1 to 16: 1 is the synchronized, actively locked to the reference UTC source stratum 2 is the synchronized, actively locked to a network stratum 1 server stratum 16 is the unsynchronized stratum level
C32 gntpTimeSinceRst	1.3.6.1.4.1.13827.12.1.1	Counter32	read-only	Time since NTP daemon restart.
C32 gntpIRQsHandled	1.3.6.1.4.1.13827.12.1.2	Counter32	read-only	Total number of Interrupts handled by the NTP daemon.
C32 gntpRxPkts	1.3.6.1.4.1.13827.12.1.3	Counter32	read-only	Total number of NTP request packets received by the NTP daemon.
C32 gntpRxPktsByIRQ	1.3.6.1.4.1.13827.12.1.4	Counter32	read-only	Total number of NTP request packets received via IRQ by the NTP daemon.
C32 gntpTxPkts	1.3.6.1.4.1.13827.12.1.5	Counter32	read-only	Total number of NTP reply packets transmitted by the NTP daemon.
INT gntpSentPktsPerSecond	1.3.6.1.4.1.13827.12.1.6	INTEGER	read-only	NTP reply packets sent per second by the NTP daemon.
C32 gntpUnSentPkts	1.3.6.1.4.1.13827.12.1.7	Counter32	read-only	Total number of NTP reply packets unsent by the NTP daemon.
C32 gntpIgnoredPkts	1.3.6.1.4.1.13827.12.1.8	Counter32	read-only	Total number of NTP request packets ignored by the NTP daemon.
C32 gntpDroppedPkts	1.3.6.1.4.1.13827.12.1.9	Counter32	read-only	Total number of NTP request packets dropped by the NTP daemon.
C32 gntpAuthFail	1.3.6.1.4.1.13827.12.1.10	Counter32	read-only	Total number of authentication failures detected by the NTP daemon.
INT gntpTimeFigureOfMerit	1.3.6.1.4.1.13827.12.1.11	INTEGER	read-only	The Time Figure of Merit (TFOM) value ranges from 3 to 9 and indicates the current estimate of the worst case time error. It is a logarithmic scale, with each increment indicating a tenfold increase in the worst case time error boundaries. The scale is referenced to a worst case time error of 100 picoseconds, equivalent to a TFOM of zero. During normal locked operation with GPS the TFOM is 3 and implies a worst case time error of 100 nanoseconds. During periods of signal loss, the GPS sub-system will compute an extrapolated worst case time error. One hour after the worst case time error has reached the value equivalent to a TFOM of TFOM Fault Level, the NTP server will cease to send stratum 1 reply packets and an Alarm LED will be energized.
INT gntpLeapIndBits	1.3.6.1.4.1.13827.12.1.12	INTEGER	read-only	This is a status code indicating: normal operation, a leap second to be inserted in the last minute of the current day, a leap second to be deleted in the last second of the day or an alarm condition indicating loss of timing synchronization. The leap indicator field of NTP reply packets sent from this server is set to gntpLeapIndBits.
STR gntpSyncSource	1.3.6.1.4.1.13827.12.1.13	DisplayString	read-only	This is an ASCII string identifying the synchronization source for this NTP server. It is one of GPS, an IP address of a stratum 1 server, or NONE. If it is NONE, then the server is not synchronized, has its Leap Indicator Bits in the Alarm state and is running at Stratum 16. If it is an IP address, then the server is operating as a stratum 2 server synchronized to the network connected stratum 1 server whose IP address is shown. Check the Stratum, Leap Indicator Bits and Time Figure of Merit for further information. NTP reply packets from this server will have the reference identifier field set to gntpSyncSource if it is GPS. Otherwise it will be set to either an IP address or 0.0.0.0 (NONE).
STR gntpOffsetToGPSReference	1.3.6.1.4.1.13827.12.1.14	DisplayString	read-only	This is an ASCII string containing the floating value of the current offset in units of seconds of the NTP server CPU clock to the GPS reference time. Positive values imply that the NTP server clock is ahead of the GPS reference time.
INT gntpStratum	1.3.6.1.4.1.13827.12.1.15	INTEGER	read-only	This is an integer showing the current stratum level being reported by the NTP daemon in its reply packets to clients. If it is 1, then the server is fully synchronized and delivering Stratum 1 accuracy. If it is greater than 1 and less than 16, it is synchronized to a network connected NTP server operating at one stratum lower. If it is 16, then the server is unambiguously unsynchronized. NTP clients on the network should be configured to not use the time from this server if the stratum is 16.
STR gntpVersion	1.3.6.1.4.1.13827.12.1.16	DisplayString	read-only	This is an ASCII string showing the system root file system firmware version.
STR gntpKernelVersion	1.3.6.1.4.1.13827.12.1.17	DisplayString	read-only	This is an ASCII string showing the system Linux kernel firmware version.
STR gntpOscType	1.3.6.1.4.1.13827.12.1.18	DisplayString	read-only	This is an ASCII string showing the installed oscillator type. It is one of TCXO, OCXO, or Rubidium.
STR gntpTimeMode	1.3.6.1.4.1.13827.12.1.19	DisplayString	read-only	This is an ASCII string showing the time mode of operation for any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It DOES NOT indicate the time mode of the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It can be LOCAL, GPS or UTC.
INT gntpLocalOffset	1.3.6.1.4.1.13827.12.1.20	INTEGER	read-only	This value is the local time offset configured for any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT indicate the local time offset of the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. Its units are half-hours, ranging from -25 to 25, where negative values imply that the local time is behind UTC.
INT gntpDSTStartMonth	1.3.6.1.4.1.13827.12.1.21	INTEGER	read-only	This value is the month that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT gntpDSTStartSunday	1.3.6.1.4.1.13827.12.1.22	INTEGER	read-only	This value is the Sunday of the month that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT gntpDSTStartHour	1.3.6.1.4.1.13827.12.1.23	INTEGER	read-only	This value is the hour that Daylight Savings Time begins. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It ranges from 0 to 23, where 0 is midnight.
INT gntpDSTStopMonth	1.3.6.1.4.1.13827.12.1.24	INTEGER	read-only	This value is the month that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT gntpDSTStopSunday	1.3.6.1.4.1.13827.12.1.25	INTEGER	read-only	This value is the Sunday of the month that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC.
INT gntpDSTStopHour	1.3.6.1.4.1.13827.12.1.26	INTEGER	read-only	This value is the hour that Daylight Savings Time ends. It affects the local time operation of any optional IRIG timecode outputs or the optional front panel vacuum fluorescent display. It is only pertinent when gntpTimeMode is set to LOCAL. It DOES NOT affect the Linux OS clock or the NTP sub-system. Both of these are ALWAYS UTC. It ranges from 0 to 23, where 0 is midnight.
STR gntpCPUDieTemperature	1.3.6.1.4.1.13827.12.1.27	DisplayString	read-only	ASCII string representing the current CPU internal die temperature, in units of Celsius degrees in floating point notation.
INT gntpCPUFreeMemory	1.3.6.1.4.1.13827.12.1.28	INTEGER	read-only	This value is the CPU Free Memory in kiloBytes.
INT gntpCPULoadAveragePerCent	1.3.6.1.4.1.13827.12.1.29	INTEGER	read-only	This value is the CPU Load Average as percent of total load.
gps	1.3.6.1.4.1.13827.12.2
gpstrap	1.3.6.1.4.1.13827.12.2.0
NTF gpsTrapFaultStatusChange	1.3.6.1.4.1.13827.12.2.0.1			A gpsTrapFaultStatusChange trap signifies that the value of the least significant two nibbles of the fault status word reported by the GPS sub-system has changed. The current value is contained in the included gpsFaultStatus.
NTF gpsTrapFault2StatusChange	1.3.6.1.4.1.13827.12.2.0.2			A gpsTrapFault2StatusChange trap signifies that the value of the most significant two nibbles of the fault status word reported by the GPS sub-system has changed. The current value is contained in the included gpsFault2Status.
NTF gpsTrapTimeFigureOfMeritChange	1.3.6.1.4.1.13827.12.2.0.3			A gpsTrapTimeFigureOfMeritChange trap signifies that the value of the TFOM reported by the GPS sub-system has changed. The current value is contained in the included gpsTimeFigureOfMerit.
BIT gpsFaultStatus	1.3.6.1.4.1.13827.12.2.1	Bits	read-only	This is a bit string contained in one character representing the least significant two nibbles of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 7: DAC controlling the TCXO is near the high or low limit. Bit 6: Time Figure of Merit has been >= TFOM Fault Level for 1 hour. Bit 5: Field Programmable Gate Array (FPGA) did not configure properly. Bit 4: FLASH memory had a write fault. Bit 3: GPS receiver communication fault. Bit 2: GPS reference time fault (fails sanity checks). Bit 1: NTP daemon is not polling the GPS reference clock. Bit 0: GPS antenna or feedline is shorted or open. ATTENTION: This object is deprecated for use in snmpget queries due to a defect in reporting for one specific combination of bits. It remains in this MIB for use with the gpsTrapFaultStatusChange object, where it reports accurately. Use the new gpsFaultNibble0Status and gpsFaultNibble1Status objects for polling via snmpget.
BIT gpsFault2Status	1.3.6.1.4.1.13827.12.2.2	Bits	read-only	This is a bit string contained in one character representing the most significant two nibbles of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 7: Primary Redundant Power Supply is Faulting. Bit 6: Secondary Redundant Power Supply is Faulting. Bit 5: Oscillator PLL Faulting. Bit 4: Not Used. Bit 3: Not Used. Bit 2: Not Used. Bit 1: Not Used. Bit 0: Installed System Power exceeds maximum. ATTENTION: This object is deprecated for use in snmpget queries due to a defect in reporting for one specific combination of bits. It remains in this MIB for use with the gpsTrapFault2StatusChange object, where it reports accurately. Use the new gpsFaultNibble2Status and gpsFaultNibble3Status objects for polling via snmpget.
INT gpsTimeFigureOfMerit	1.3.6.1.4.1.13827.12.2.3	INTEGER	read-only	The Time Figure of Merit (TFOM) value ranges from 3 to 9 and indicates the current estimate of the worst case time error. It is a logarithmic scale, with each increment indicating a tenfold increase in the worst case time error boundaries. The scale is referenced to a worst case time error of 100 picoseconds, equivalent to a TFOM of zero. During normal locked operation the TFOM is 3 and implies a worst case time error of 100 nanoseconds. During periods of signal loss, the GPS sub-system will compute an extrapolated worst case time error. One hour after the worst case time error has reached the value equivalent to a TFOM of TFOM Fault Level, the NTP server will cease to send stratum 1 reply packets and an Alarm LED will be energized.
STR gpsSigProcState	1.3.6.1.4.1.13827.12.2.4	DisplayString	read-only	Current GPS signal processor state. One of WRM, ACQ, LKG or LKD with WRM indicating either an OCXO or Rubidium is warming up, ACQ indicating the acquisition state and LKD the fully locked on state. This is the status of the lock of the main system timing signals to the GPS Receiver.
INT gpsNumTrackSats	1.3.6.1.4.1.13827.12.2.5	INTEGER	read-only	Current number of GPS satellites being tracked.
STR gpsAvgCarrierToNoiseRatiodB	1.3.6.1.4.1.13827.12.2.6	DisplayString	read-only	ASCII string representing the current average carrier to noise ratio of all tracked satellites, in units of dB. Values less than 35 indicate weak signal conditions.
STR gpsChannelTrkStat1	1.3.6.1.4.1.13827.12.2.7	DisplayString	read-only	Channel 1 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat2	1.3.6.1.4.1.13827.12.2.8	DisplayString	read-only	Channel 2 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat3	1.3.6.1.4.1.13827.12.2.9	DisplayString	read-only	Channel 3 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat4	1.3.6.1.4.1.13827.12.2.10	DisplayString	read-only	Channel 4 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat5	1.3.6.1.4.1.13827.12.2.11	DisplayString	read-only	Channel 5 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat6	1.3.6.1.4.1.13827.12.2.12	DisplayString	read-only	Channel 6 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat7	1.3.6.1.4.1.13827.12.2.13	DisplayString	read-only	Channel 7 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat8	1.3.6.1.4.1.13827.12.2.14	DisplayString	read-only	Channel 8 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat9	1.3.6.1.4.1.13827.12.2.15	DisplayString	read-only	Channel 9 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat10	1.3.6.1.4.1.13827.12.2.16	DisplayString	read-only	Channel 10 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat11	1.3.6.1.4.1.13827.12.2.17	DisplayString	read-only	Channel 11 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsChannelTrkStat12	1.3.6.1.4.1.13827.12.2.18	DisplayString	read-only	Channel 12 tracking status of the GPS receiver. Information includes the Satellite ID #, the Azimuth angle in degrees, the Elevation angle in degrees and the Carrier to Noise ratio, C/No in dB. If the Satellite ID # is 0, then no satellite is being tracked in this channel.
STR gpsLastPositionFix	1.3.6.1.4.1.13827.12.2.19	DisplayString	read-only	WGS-84 latitude, longitude and height above the reference ellipsoid of the GPS antenna. Ellipsoid height may deviate from local Mean Sea Level by as much as 100 meters. This value is the last instantaneous position fix as reported by the GPS receiver. It is not averaged.
STR gpsReferencePosition	1.3.6.1.4.1.13827.12.2.20	DisplayString	read-only	WGS-84 latitude, longitude and height above the reference ellipsoid of the GPS antenna. Ellipsoid height may deviate from local Mean Sea Level by as much as 100 meters. When the GPS Dynamic Mode is OFF or Static, this value is the result of a 24 hour average of fixes that is used to establish the precise timing reference position.
STR gpsRefPosSource	1.3.6.1.4.1.13827.12.2.21	DisplayString	read-only	ASCII string indicating the source of the GPS antenna reference position. It is one of: USR (user supplied), AVG (automatically determined by averaging thousands of 3-D position fixes), DYN (current un-averaged 3-D position fix, operation is in dynamic mode), UNK (unknown).
INT gpsCurrentLeapSeconds	1.3.6.1.4.1.13827.12.2.22	INTEGER	read-only	This value is the current difference in seconds between GPS time and UTC time. GPS time is ahead of UTC time by this amount.
INT gpsFutureLeapSeconds	1.3.6.1.4.1.13827.12.2.23	INTEGER	read-only	This value is the future difference in seconds between GPS time and UTC time. Leap seconds may be inserted or deleted from the UTC timescale twice during the year: Dec 31 and June 30 at UTC midnight. If this value is the same as gpsCurrentLeapSeconds, then no leap second insertion or deletion will occur at the next possible time. If it is different, then the change will take affect at the next possible time. GPS time will be ahead of UTC time by this amount.
INT gpsAlmanacLS	1.3.6.1.4.1.13827.12.2.24	INTEGER	read-only	This value, LS is the current difference in seconds between GPS time and UTC time as contained in the GPS Almanac UTC data. GPS time is ahead of UTC time by this amount. For more detailed information, consult the GPS-ICD-200.
INT gpsAlmanacLSF	1.3.6.1.4.1.13827.12.2.25	INTEGER	read-only	This value, LSF is the future difference in seconds between GPS time and UTC time as contained in the GPS Almanac UTC data. Leap seconds may be inserted or deleted from the UTC timescale twice during the year: Dec 31 and June 30 at UTC midnight. If this value is the same as gpsAlmLS, then no leap second insertion or deletion will occur at the next possible time. If it is different, then the change will take affect at the time defined by the GPS Almanac parameters, WN_lsf and DN. GPS time will be ahead of UTC time by this amount. For more detailed information, consult the GPS-ICD-200.
INT gpsAlmanacUTCWNlsf	1.3.6.1.4.1.13827.12.2.26	INTEGER	read-only	This value, WN_lsf is the GPS Week Number during which the UTC leap second offset to GPS time will transition to the Leap Second Future value. The GPS week numbers began on January 6, 1980 with week number 0. If a leap second has recently been inserted, this week number could be in the past, in which case the current and future leap seconds values will be equal. For more detailed information, consult the GPS-ICD-200.
INT gpsAlmanacUTCDN	1.3.6.1.4.1.13827.12.2.27	INTEGER	read-only	This value, DN is the Day Number of the week in which the UTC leap second offset to GPS time will transition to the Leap Second Future value. The GPS day numbers begin on Sunday with day number 1. The leap second insertion occurs at the end of the given day. For more detailed information, consult the GPS-ICD-200.
STR gpsAlmanacA0	1.3.6.1.4.1.13827.12.2.28	DisplayString	read-only	ASCII string representing the value of the a0 coefficient of the linear fit of the UTC offset to GPS time. a0 is the constant term in the equation, in units of seconds, in scientific floating point notation. The GPS and UTC timescales are separated by leap seconds and another small error, typically less than 10 nanoseconds, which is estimated using this linear fit. For more detailed information, consult the GPS-ICD-200.
STR gpsAlmanacA1	1.3.6.1.4.1.13827.12.2.29	DisplayString	read-only	ASCII string representing the value of the a1 coefficient of the linear fit of the UTC offset to GPS time. a1 is the slope term in the equation, in units of seconds per second, in scientific floating point notation. The GPS and UTC timescales are separated by leap seconds and another small error, typically less than 10 nanoseconds, which is estimated using this linear fit. For more detailed information, consult the GPS-ICD-200.
INT gpsAlmanacUTCWNt	1.3.6.1.4.1.13827.12.2.30	INTEGER	read-only	This value, WN_t is the GPS Week Number during which the reference time for the linear fit equation defined by a0 and a1 occurs. It is used along with t_ot to calculate a value of GPS seconds to offset the linear fit in the time domain. For more detailed information, consult the GPS-ICD-200.
INT gpsAlmanacUTCtot	1.3.6.1.4.1.13827.12.2.31	INTEGER	read-only	This value, t_ot is the second of the GPS week WN_t at which time the linear fit equation defined by a0 and a1 will evaluate to a0. The seconds range from 0 at the beginning of day number 1 to 604799 at the end of day number 7. For more detailed information, consult the GPS-ICD-200.
INT gpsGPSminusUTCOffset	1.3.6.1.4.1.13827.12.2.32	INTEGER	read-only	This value, (GPS - UTC) is the current sub-seconds offset of the GPS timescale to the UTC timescale, computed using the received GPS almanac parameters (WN_t, t_ot, a0 and a1) and the current GPS week number and time-of-week. The units are in picoseconds. This value must be added to the current leap seconds offset to fully quantify the amount that the GPS timescale is ahead of the UTC timescale. For more detailed information, consult the GPS-ICD-200.
STR gpsVersion	1.3.6.1.4.1.13827.12.2.33	DisplayString	read-only	ASCII string showing the GPS sub-system firmware and FPGA versions.
INT gpsDynamicMode	1.3.6.1.4.1.13827.12.2.34	INTEGER	read-only	The GPS dynamic mode is either on or off. When it is off, the server is assumed to be in a static installation. In this case, single satellite mode of operation is supported and Timing Receiver Autonomous Integrity Monitoring (TRAIM) is supported. When the setting is on, the server is assumed to be on a moving platform. In this case, minimum four satellite, 3-D operation is required and the TRAIM functionality is minimal.
INT gpsCalibrationDelay	1.3.6.1.4.1.13827.12.2.35	INTEGER	read-only	Signed integer representing the current calibration delay being applied to the timing outputs, in units of nanoseconds. Positive values indicate that the timing outputs are advanced.
INT gpsCoastDuration	1.3.6.1.4.1.13827.12.2.36	INTEGER	read-only	Unsigned integer representing the current elapsed time since the unit lost GPS reception in units of seconds.
STR gpsEstimatedTimeError	1.3.6.1.4.1.13827.12.2.37	DisplayString	read-only	ASCII string representing the magnitude of the estimated time error since the unit lost GPS reception, in units of seconds in scientific floating point notation. While locked, the value is the magnitude of the measured time error relative to GPS.
STR gpsMeasuredTimeError	1.3.6.1.4.1.13827.12.2.38	DisplayString	read-only	ASCII string representing the measured time error of the timing outputs relative to GPS, in units of seconds in scientific floating point notation. While coasting, the value is the last measured value prior to losing GPS reception.
STR gpsMeasurementTimeDeviation	1.3.6.1.4.1.13827.12.2.39	DisplayString	read-only	ASCII string representing the time deviation (TDEV) of the GPS measurement data, in units of seconds in scientific floating point notation. While coasting, the value is the last computed value prior to losing GPS reception.
INT gpsOSCDAC	1.3.6.1.4.1.13827.12.2.40	INTEGER	read-only	Current 20 bit, System Voltage Controlled Oscillator DAC value. Typical range is 320000 to 640000, where more positive numbers have the effect of raising the oscillator frequency.
STR gpsMeasuredOscillatorAgeing	1.3.6.1.4.1.13827.12.2.41	DisplayString	read-only	ASCII string representing the ageing rate per day of the installed osc- illator, in scientific floating point notation. It is computed via linear regression and requires several hours following initial lock to GPS to see the first update. While coasting, the value is the last computed value prior to losing GPS reception.
STR gpsControlLoopTimeConstant	1.3.6.1.4.1.13827.12.2.42	DisplayString	read-only	ASCII string representing the current equivalent averaging time of the oscillator control loop, in units of seconds in floating point notation. The value is dynamically updated based on the stability of the oscillator.
STR gpsInternalTemperature	1.3.6.1.4.1.13827.12.2.43	DisplayString	read-only	ASCII string representing the current internal chassis temperature, in units of Celsius degrees in floating point notation. A value is only available when the installed oscillator is an OCXO or Rubidium.
STR gpsAntennaFaultMask	1.3.6.1.4.1.13827.12.2.44	DisplayString	read-only	The GPS antenna fault mask is either on or off. When it is off, the server will set the Antenna Fault Bit in the Fault Status Byte if an improper antenna impedance is detected. When the setting is on, the server will not set the Antenna Fault Bit in the Fault Status Byte if an improper antenna impedance is detected.
STR gpsSignalLossFaultMask	1.3.6.1.4.1.13827.12.2.45	DisplayString	read-only	The GPS signal loss fault mask is either on or off. When it is off, the server will set the Signal Loss Fault Bit in the Fault Status Byte one hour after TFOM reaches the TFOM Fault Level. When the setting is on, the server will not set the Signal Loss Fault Bit in the Fault Status Byte one hour or more after TFOM reaches TFOM Fault level.
STR gpsPrimaryPowerFaultAlarmMask	1.3.6.1.4.1.13827.12.2.46	DisplayString	read-only	The Primary Power input fault alarm mask is either on or off. When it is on, the server will not assert an Alarm condition on a fault in the Primary Power supply. Unlike other fault masks, the fault condition will continue to be visible in the Fault Status Byte. This mask capability is useful when performing system tests when only a single power input is available and an alarm would be undesirable. When the setting is off, the server will assert an Alarm condition in addition to setting the appropriate bit in the Fault Status Byte.
STR gpsSecondaryPowerFaultAlarmMask	1.3.6.1.4.1.13827.12.2.47	DisplayString	read-only	The Secondary Power input fault alarm mask is either on or off. When it is on, the server will not assert an Alarm condition on a fault in the Secondary Power supply. Unlike other fault masks, the fault condition will continue to be visible in the Fault Status Byte. This mask capability is useful when performing system tests when only a single power input is available and an alarm would be undesirable. When the setting is off, the server will assert an Alarm condition in addition to setting the appropriate bit in the Fault Status Byte.
BIT gpsFaultNibble0Status	1.3.6.1.4.1.13827.12.2.48	Bits	read-only	This is a bit string contained in one character representing the least significant nibble of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: DAC controlling the TCXO is near the high or low limit. Bit 2: Time Figure of Merit has been >= TFOM Fault Level for 1 hour. Bit 1: Field Programmable Gate Array (FPGA) did not configure properly. Bit 0: FLASH memory had a write fault.
BIT gpsFaultNibble1Status	1.3.6.1.4.1.13827.12.2.49	Bits	read-only	This is a bit string contained in one character representing the second nibble of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: GPS receiver communication fault. Bit 2: GPS reference time fault (fails sanity checks). Bit 1: NTP daemon is not polling the GPS reference clock. Bit 0: GPS antenna or feedline is shorted or open.
BIT gpsFaultNibble2Status	1.3.6.1.4.1.13827.12.2.50	Bits	read-only	This is a bit string contained in one character representing the third nibble of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: Primary Redundant Power Supply is Faulting. Bit 2: Secondary Redundant Power Supply is Faulting. Bit 1: Oscillator PLL Faulting. Bit 0: Not Used.
BIT gpsFaultNibble3Status	1.3.6.1.4.1.13827.12.2.51	Bits	read-only	This is a bit string contained in one character representing the most significant nibble of the GPS fault status word. Unfortunately, SNMP numbers the bits in the reverse order, so that the enumerated values are backwards from the description contained in the User's Manual for the fault status field returned by the gpsstat command. Each bit indicates a fault when set. Currently defined fault states encoded in this value: Bit 3: Not Used. Bit 2: Not Used. Bit 1: Not Used. Bit 0: Installed System Power exceeds maximum.
gCPUIO	1.3.6.1.4.1.13827.12.3
STR gsysio1PPSWidth	1.3.6.1.4.1.13827.12.3.1	DisplayString	read-only	ASCII string showing the status of the Settable PulseWidth, 1PPS Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing the current pulsewidth setting.
STR gsysioTimeCodeFormat	1.3.6.1.4.1.13827.12.3.2	DisplayString	read-only	ASCII string showing the status of the Selectable Format, Time Code Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing the current time code output format setting.
INT gsysioSynthesizerHz	1.3.6.1.4.1.13827.12.3.3	INTEGER	read-only	Integer showing the current frequency setting of the 1 Hz resolution, Direct Digital Synthesizer (DDS) Output, system-wide I/O signal. If this option is not installed the value is -1, otherwise the value ranges from 0 to 10000000 Hz.
STR gsysioSerialTimeOutputBaudrate	1.3.6.1.4.1.13827.12.3.4	DisplayString	read-only	ASCII string showing the Baudrate of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of 4800, 9600, 19200 or 57600.
STR gsysioSerialTimeOutputFormat	1.3.6.1.4.1.13827.12.3.5	DisplayString	read-only	ASCII string showing the Format of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of SYSPLEX, TRUETIME, NENA0, NENA1, NENA8, ENDRUN, ENDRUNX or NMEA.
STR gsysioSerialTimeOutputParity	1.3.6.1.4.1.13827.12.3.6	DisplayString	read-only	ASCII string showing the Parity of the Serial Time Output, system-wide I/O signal. It may be NOT INSTALLED, or a string showing one of ODD, EVEN or NONE.
STR gsysioSerialTimeNMEASentence1	1.3.6.1.4.1.13827.12.3.7	DisplayString	read-only	ASCII string showing the first NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE.
STR gsysioSerialTimeNMEASentence2	1.3.6.1.4.1.13827.12.3.8	DisplayString	read-only	ASCII string showing the second NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE.
STR gsysioSerialTimeNMEASentence3	1.3.6.1.4.1.13827.12.3.9	DisplayString	read-only	ASCII string showing the third NMEA sentence selected for output from the Serial Time Output, system-wide I/O signal. This sentence is only output from the Meridian2 when the Serial Time Output Format is set to NMEA. It may be NOT INSTALLED, or a string showing one of GGA, GLL, GSA, GSV1, GSV2, RMC, VTG, ZDA or NONE.
STR gcpuioConnA	1.3.6.1.4.1.13827.12.3.10	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector A. It may be NOT INSTALLED, or a string showing the current I/O selection.
STR gcpuioConnB	1.3.6.1.4.1.13827.12.3.11	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector B. It may be NOT INSTALLED, or a string showing the current I/O selection.
STR gcpuioConnC	1.3.6.1.4.1.13827.12.3.12	DisplayString	read-only	ASCII string showing the status of the CPU I/O Connector C. It may be NOT INSTALLED, or a string showing the current I/O selection.
gptp0	1.3.6.1.4.1.13827.12.4
INT gptp0Version	1.3.6.1.4.1.13827.12.4.1	INTEGER	read-only	This value is the Version of the Precise Time Protocol, which is 2.
INT gptp0SyncInterval	1.3.6.1.4.1.13827.12.4.2	INTEGER	read-only	This value is the log base 2 of the PTP Sync Interval in seconds. Values range from -7 to 0, which covers the range from 1/128 to 1 second.
INT gptp0AnnounceInterval	1.3.6.1.4.1.13827.12.4.3	INTEGER	read-only	This value is the log base 2 of the PTP Announce Interval in seconds. Values range from 0 to 4, which covers the range from 1 to 16 seconds.
INT gptp0Priority1	1.3.6.1.4.1.13827.12.4.4	INTEGER	read-only	This value is the PTP Priority1 parameter. It ranges from 0 to 255.
INT gptp0Priority2	1.3.6.1.4.1.13827.12.4.5	INTEGER	read-only	This value is the PTP Priority2 parameter. It ranges from 0 to 255.
INT gptp0DelayMechanism	1.3.6.1.4.1.13827.12.4.6	INTEGER	read-only	This value maps to the PTP Delay Mechanism, one of E2E, P2P or disabled.
INT gptp0Domain	1.3.6.1.4.1.13827.12.4.7	INTEGER	read-only	This value is the PTP Domain parameter. It ranges from 0 to 255.
INT gptp0TimeMode	1.3.6.1.4.1.13827.12.4.8	INTEGER	read-only	This value maps to the PTP Time Mode, one of UTC or PTP.
INT gptp0TTL	1.3.6.1.4.1.13827.12.4.9	INTEGER	read-only	This value is the PTP multicast Time-To-Live parameter. It ranges from 1 to 255.
INT gptp0ClockClass	1.3.6.1.4.1.13827.12.4.10	INTEGER	read-only	This value maps to the PTP Clock Class, one of Locked, Holdover or Unlocked on either the PTP or arbitrary, i.e. UTC time scale.
INT gptp0TimeScale	1.3.6.1.4.1.13827.12.4.11	INTEGER	read-only	This value maps to the PTP Time Scale, one of ARB or PTP. When operating in other than PTP Time Mode, this value is always ARB, arbitrary.
INT gptp0PortState	1.3.6.1.4.1.13827.12.4.12	INTEGER	read-only	This value maps to the PTP Port State, one of Initializing, Faulty, Disabled, Listening, PreMaster, Master, Passive, Uncalibrated or Slave.
INT gptp0TimeSource	1.3.6.1.4.1.13827.12.4.13	INTEGER	read-only	This value maps to the PTP Time Source, one of Atom, GPS, Radio, PTP, NTP, Hand, Other or Oscillator.
INT gptp0UTCOffset	1.3.6.1.4.1.13827.12.4.14	INTEGER	read-only	This value is the UTC offset from Atomic Time in seconds. It is currently 35 seconds.
INT gptp0UTCOffsetValid	1.3.6.1.4.1.13827.12.4.15	INTEGER	read-only	This value maps to the validity of the UTC offset from Atomic Time in seconds. It is either False or True.
INT gptp0ClockAccuracy	1.3.6.1.4.1.13827.12.4.16	INTEGER	read-only	This value maps to the PTP Clock Accuracy, with values ranging from 25 nanoseconds to Unknown.
INT gptp0Leap59	1.3.6.1.4.1.13827.12.4.17	INTEGER	read-only	This value maps to the state of the Leap 59 second indicator, which when True, indicates that a UTC leap second deletion event is imminent. It is either False or True.
INT gptp0Leap61	1.3.6.1.4.1.13827.12.4.18	INTEGER	read-only	This value maps to the state of the Leap 61 second indicator, which when True, indicates that a UTC leap second insertion event is imminent. It is either False or True.
INT gptp0TimeTraceable	1.3.6.1.4.1.13827.12.4.19	INTEGER	read-only	This value maps to the state of the PTP Time Traceable indicator, which when True, indicates that the time of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
INT gptp0FreqTraceable	1.3.6.1.4.1.13827.12.4.20	INTEGER	read-only	This value maps to the state of the PTP Frequency Traceable indicator, which when True, indicates that the frequency of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
gptp1	1.3.6.1.4.1.13827.12.5
INT gptp1Version	1.3.6.1.4.1.13827.12.5.1	INTEGER	read-only	This value is the Version of the Precise Time Protocol, which is 2.
INT gptp1SyncInterval	1.3.6.1.4.1.13827.12.5.2	INTEGER	read-only	This value is the log base 2 of the PTP Sync Interval in seconds. Values range from -7 to 0, which covers the range from 1/128 to 1 second.
INT gptp1AnnounceInterval	1.3.6.1.4.1.13827.12.5.3	INTEGER	read-only	This value is the log base 2 of the PTP Announce Interval in seconds. Values range from 0 to 4, which covers the range from 1 to 16 seconds.
INT gptp1Priority1	1.3.6.1.4.1.13827.12.5.4	INTEGER	read-only	This value is the PTP Priority1 parameter. It ranges from 0 to 255.
INT gptp1Priority2	1.3.6.1.4.1.13827.12.5.5	INTEGER	read-only	This value is the PTP Priority2 parameter. It ranges from 0 to 255.
INT gptp1DelayMechanism	1.3.6.1.4.1.13827.12.5.6	INTEGER	read-only	This value maps to the PTP Delay Mechanism, one of E2E, P2P or disabled.
INT gptp1Domain	1.3.6.1.4.1.13827.12.5.7	INTEGER	read-only	This value is the PTP Domain parameter. It ranges from 0 to 255.
INT gptp1TimeMode	1.3.6.1.4.1.13827.12.5.8	INTEGER	read-only	This value maps to the PTP Time Mode, one of UTC or PTP.
INT gptp1TTL	1.3.6.1.4.1.13827.12.5.9	INTEGER	read-only	This value is the PTP multicast Time-To-Live parameter. It ranges from 1 to 255.
INT gptp1ClockClass	1.3.6.1.4.1.13827.12.5.10	INTEGER	read-only	This value maps to the PTP Clock Class, one of Locked, Holdover or Unlocked on either the PTP or arbitrary, i.e. UTC time scale.
INT gptp1TimeScale	1.3.6.1.4.1.13827.12.5.11	INTEGER	read-only	This value maps to the PTP Time Scale, one of ARB or PTP. When operating in other than PTP Time Mode, this value is always ARB, arbitrary.
INT gptp1PortState	1.3.6.1.4.1.13827.12.5.12	INTEGER	read-only	This value maps to the PTP Port State, one of Initializing, Faulty, Disabled, Listening, PreMaster, Master, Passive, Uncalibrated or Slave.
INT gptp1TimeSource	1.3.6.1.4.1.13827.12.5.13	INTEGER	read-only	This value maps to the PTP Time Source, one of Atom, GPS, Radio, PTP, NTP, Hand, Other or Oscillator.
INT gptp1UTCOffset	1.3.6.1.4.1.13827.12.5.14	INTEGER	read-only	This value is the UTC offset from Atomic Time in seconds. It is currently 35 seconds.
INT gptp1UTCOffsetValid	1.3.6.1.4.1.13827.12.5.15	INTEGER	read-only	This value maps to the validity of the UTC offset from Atomic Time in seconds. It is either False or True.
INT gptp1ClockAccuracy	1.3.6.1.4.1.13827.12.5.16	INTEGER	read-only	This value maps to the PTP Clock Accuracy, with values ranging from 25 nanoseconds to Unknown.
INT gptp1Leap59	1.3.6.1.4.1.13827.12.5.17	INTEGER	read-only	This value maps to the state of the Leap 59 second indicator, which when True, indicates that a UTC leap second deletion event is imminent. It is either False or True.
INT gptp1Leap61	1.3.6.1.4.1.13827.12.5.18	INTEGER	read-only	This value maps to the state of the Leap 61 second indicator, which when True, indicates that a UTC leap second insertion event is imminent. It is either False or True.
INT gptp1TimeTraceable	1.3.6.1.4.1.13827.12.5.19	INTEGER	read-only	This value maps to the state of the PTP Time Traceable indicator, which when True, indicates that the time of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.
INT gptp1FreqTraceable	1.3.6.1.4.1.13827.12.5.20	INTEGER	read-only	This value maps to the state of the PTP Frequency Traceable indicator, which when True, indicates that the frequency of the PTP synchronization messages is traceable to the designated time scale. It is either False or True.

RFC description

EndRun Technologies Sonoma CDMA time server and NTP clock monitoring.

Start monitoring EndRun Technologies GPS/CDMA network time server appliance (NTP engine/timing-quality status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SONOMA-MIB