SMA-MIB

All MIBs › SMA-MIB

Organization: IETF IP Over IB Working Group Email: ipoib@ietf.org

Last Updated: 2003-06-06

Category: InfiniBand Fabric Management

Description: Defines IETF InfiniBand Subnet Management Agent objects for IB fabric topology discovery and port management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SMA-MIB?

SMA-MIB is an IETF IP Over IB (InfiniBand) Working Group standard MIB defining managed objects for the Subnet Management Agent (SMA) instrumentation on an InfiniBand node. Its objects cover node string/base version/class version/type, port count, system-image GUID, node/port GUID, partition-table count, device ID, revision, local-port number, vendor ID, LID (Local Identifier), port number, method, attribute ID/modifier, key, a second LID, service level, and up to two queue-pair and GID (Global Identifier) values used in SMA management-datagram addressing. As a status MIB it lets an administrator confirm InfiniBand node identity and SMA addressing parameters on an InfiniBand fabric device. It is deployed on InfiniBand fabric equipment (Subnet Management Agent). Engineers implementing or auditing this functionality typically reference the SMA-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in SMA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

InfiniBand fabric equipment (Subnet Management Agent)

Monitoring Examples

An administrator checks ibSmaNodeGuid and ibSmaNodeLid to confirm a device's InfiniBand node identity and subnet-management addressing.

What Can Be Monitored

InfiniBand node identity and SMA addressing parameters

Imported Objects

From IB-TC-MIB

IbDataPort
IbDataPortAndInvalid
IbGuid
IbMulticastLid
IbSmPortList
IbUnicastLid
infinibandMIB	OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
experimental

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using ibSmaSmSmpCount OID:

Select an InfiniBand fabric equipment, Subnet Management Agent (node/port identity and SMA addressing status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ibSmaSmSmpCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the counter that increments each time the SM issues an SMP or performs other management activities. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ibSmaMIB	1.3.6.1.3.117.3			This module contains managed object definitions for the Subnet Management Agent instrumentation for an InfiniBand Subnet Management Agent (SMA).
ibSmaObjects	1.3.6.1.3.117.3.1
ibSmaNodeInfo	1.3.6.1.3.117.3.1.1
STR ibSmaNodeString	1.3.6.1.3.117.3.1.1.1	DisplayString	read-only	The node description. This is the Node description string from the NodeDescription attribute. The contents of the NodeDescription attribute is the same for all ports on a node.
I32 ibSmaNodeBaseVersion	1.3.6.1.3.117.3.1.1.2	Integer32	read-only	The supported Management Datagram (MAD) base version. This value indicates that the node supports up to and including this version. This value is the same for all ports on a node. (NOTE: for InfiniBand Release 1 this value should be set to 1.)
I32 ibSmaNodeClassVersion	1.3.6.1.3.117.3.1.1.3	Integer32	read-only	The supported Subnet Management Class (SMP) version. This value indicates that the node supports up to and including this version. This value is the same for all ports on a node. (NOTE: for InfiniBand Release 1 this value should be set to 1.)
INT ibSmaNodeType	1.3.6.1.3.117.3.1.1.4	INTEGER	read-only	Type of IBA device this SMA is supporting. Types are 1: Channel Adapter 2: Switch 3: Router 0,4-255: reserved NOTE: all reserved values are reported as other.
I32 ibSmaNodeNumPorts	1.3.6.1.3.117.3.1.1.5	Integer32	read-only	The number of physical InfiniBand ports on this node.
IBG ibSmaSystemImageGuid	1.3.6.1.3.117.3.1.1.6	IbGuid	read-only	The GUID of this node that associates this node with other nodes in the same administrative domain. These nodes are controlled by common supervisory code. This object provides a way for system software to indicate the availability of multiple paths to the same destination via multiple nodes. If this value is 0, there is no association. This object may be equal to the ibSmaNodeGuid of one of the associated nodes if that node is not field-replaceable.
IBG ibSmaNodeGuid	1.3.6.1.3.117.3.1.1.7	IbGuid	read-only	The GUID of this node. The node can be an HCA, TCA, switch, or router. All ports on the same node shall report the same NodeGUID value. This provides a means for uniquely identifing a node within a subnet and helps to determine the co-location of the ports.
IBG ibSmaNodePortGuid	1.3.6.1.3.117.3.1.1.8	IbGuid	read-only	The GUID of this port. One port within a node can return the NodeGUID as its PortGUID if the port is an integral part of the node and is not field-replaceable.
I32 ibSmaNodePartitionTableNum	1.3.6.1.3.117.3.1.1.9	Integer32	read-only	Number of entries in the Partition Table for CA, router, and the switch management port. This is at a minimum set to 1 for all nodes including switches. This value shall be the same for all ports on a node.
OCT ibSmaNodeDeviceId	1.3.6.1.3.117.3.1.1.10	OCTET STRING	read-only	Device ID information as assigned by the device manufacturer. This value shall be the same for all ports on a node.
OCT ibSmaNodeRevision	1.3.6.1.3.117.3.1.1.11	OCTET STRING	read-only	Device revision as assigned by manufacturer. This value shall be the same for all ports on a node.
I32 ibSmaNodeLocalPortNumOrZero	1.3.6.1.3.117.3.1.1.12	Integer32	read-only	The number of the IBA port which received this SNMP request. If the port is unknown a 0 is returned.
OCT ibSmaNodeVendorId	1.3.6.1.3.117.3.1.1.13	OCTET STRING	read-only	Device vendor Identifier as specified by the IEEE. This value shall be the same for all ports on a node.
I32 ibSmaNodeLid	1.3.6.1.3.117.3.1.1.14	Integer32	accessible-for-notify	Local Identifier value. Used for notification var bind list object. Retrieved from InfiniBand traps 128, 129, 130, 131, 144, 145, 256, 257, 258, and 259.
IBD ibSmaNodePortNum	1.3.6.1.3.117.3.1.1.15	IbDataPort	accessible-for-notify	Port number. Used for notification var bind list object. Retrieved from InfiniBand traps 129, 130, 131, and 259.
I32 ibSmaNodeMethod	1.3.6.1.3.117.3.1.1.16	Integer32	accessible-for-notify	Method. Used for notification var bind list object. Retrieved from InfiniBand trap 256.
U32 ibSmaNodeAttributeId	1.3.6.1.3.117.3.1.1.17	Unsigned32	accessible-for-notify	Attribute ID. Used for notification var bind list object. Retrieved from InfiniBand trap 256.
U32 ibSmaNodeAttributeModifier	1.3.6.1.3.117.3.1.1.18	Unsigned32	accessible-for-notify	Attribute Modifier. Used for notification var bind list object. Retrieved from InfiniBand trap 256.
OCT ibSmaNodeKey	1.3.6.1.3.117.3.1.1.19	OCTET STRING	accessible-for-notify	M_Key, Q_Key or P_Key. Used for notification var bind list object. Retrieved from InfiniBand traps 256, 257, 258, and 259. Note: If it is a P_Key, the 16 most significant bits of the field shall be set to 0 and the least significant bits of the field will be set to the P_Key.
I32 ibSmaNodeLid2	1.3.6.1.3.117.3.1.1.20	Integer32	accessible-for-notify	To Local Identifier (LID). Used for notification var bind list object. Retrieved from InfiniBand traps 257, 258, and 259.
I32 ibSmaNodeServiceLevel	1.3.6.1.3.117.3.1.1.21	Integer32	accessible-for-notify	Service Level. Used for notification var bind list object. Retrieved from InfiniBand traps 257, 258, and 259.
I32 ibSmaNodeQueuePair1	1.3.6.1.3.117.3.1.1.22	Integer32	accessible-for-notify	Queue Pair (QP) 1. Used for notification var bind list object. Retrieved from InfiniBand traps 257, 258, and 259.
I32 ibSmaNodeQueuePair2	1.3.6.1.3.117.3.1.1.23	Integer32	accessible-for-notify	Queue Pair (QP) 2. Used for notification var bind list object. Retrieved from InfiniBand traps 257, 258, and 259.
OCT ibSmaNodeGid1	1.3.6.1.3.117.3.1.1.24	OCTET STRING	accessible-for-notify	Global Identifier 1. Used for notification var bind list object. Retrieved from InfiniBand traps 64, 65, 66, 67, 257, 258, and 259. Note: If no GRH is present in the offending packet, this value will be 0.
OCT ibSmaNodeGid2	1.3.6.1.3.117.3.1.1.25	OCTET STRING	accessible-for-notify	Global Identifier 2. Used for notification var bind list object. Retrieved from InfiniBand traps 257, 258, and 258. Note: If no GRH is present in the offending packet, this value will be 0.
OCT ibSmaNodeCapMask	1.3.6.1.3.117.3.1.1.26	OCTET STRING	accessible-for-notify	Contents of Capability Mask. Retrieved from InfiniBand trap 144.
I32 ibSmaNodeSwitchLid	1.3.6.1.3.117.3.1.1.27	Integer32	accessible-for-notify	The switch Local Identifier (LID). Used for notification var bind list object. Retrieved from InfiniBand traps 259.
OCT ibSmaNodeDataValid	1.3.6.1.3.117.3.1.1.28	OCTET STRING	accessible-for-notify	Data valid field retrieved from InfiniBand trap 259. It is a bit mask. If the bit is set, the field is valid. bit 0: LIDADDR1 bit 1: LIDADDR2 bit 2: PKEY bit 3: SL bit 4: QP1 bit 5: QP2 bit 6: GIDADDR1 bit 7: GIDADDR2 bit 8-15: reserved (0).
ibSmaSwitchInfo	1.3.6.1.3.117.3.1.2
I32 ibSmaSwLinearFdbTableNum	1.3.6.1.3.117.3.1.2.1	Integer32	read-only	Number of entries in the Linear Forwarding Data Base. This counts the number of entries supported in the Linear Unicast Forwarding Table (starting at LID=0x0000 and going up). The InfiniBand SwitchInfo component is called LinearFDBCap. When this count is 0, this indicates that there is no Linear Forwarding Database present.
I32 ibSmaSwRandomFdbTableNum	1.3.6.1.3.117.3.1.2.2	Integer32	read-only	Number of entries in the Random Forwarding Data Base. This counts the number of entries supported in the Random Unicast Forwarding Table. The InfiniBand SwitchInfo component is called RandomFDBCap. When this count is 0, this indicates that there is no Random Forwarding Database present.
I32 ibSmaSwMulticastFdbTableNum	1.3.6.1.3.117.3.1.2.3	Integer32	read-only	Number of entries in the Multicast Forwarding Data Base. This counts the number of entries supported in the Multicast Forwarding Table (starting at LID=0xC000 and going up). The InfiniBand SwitchInfo component is called MulticastFDBCap.
I32 ibSmaSwLinearFdbTop	1.3.6.1.3.117.3.1.2.4	Integer32	read-only	Indicates the top of the linear forwarding database. Packets received with unicast DLIDs greater than this value are discarded by the switch. A valid LinearFdbTop is less than LinearFdbCap. This component applies only to switches that implement linear forwarding tables and is ignored by switches that implement random forwarding tables. For the latter cases a 0 is returned.
I32 ibSmaSwDefaultPort	1.3.6.1.3.117.3.1.2.5	Integer32	read-only	Default forwarding port for unicast packets from the other ports whose DLID does not exist in the random forwarding table. If the port number is unknown, a 0 is returned. If this object is set to a non-existent port, subsequent responses may contain any non-existent port number.
I32 ibSmaSwDefMcastPriPort	1.3.6.1.3.117.3.1.2.6	Integer32	read-only	Default forwarding port for multicast packets from the other ports whose DLID does not exist in the forwarding table. If port number is unknown, a 0 is returned. If this object is set to a non-existent port, subsequent responses may contain any non-existent port number.
I32 ibSmaSwDefMcastNotPriPort	1.3.6.1.3.117.3.1.2.7	Integer32	read-only	Forward to this port all the multicast packets from the Default Primary port whose DLID does not exist in the forwarding table. If it is unknown, a 0 is returned. If this object is set to a non-existent port, subsequent responses may contain any non-existent port number.
I32 ibSmaSwLifeTimeValue	1.3.6.1.3.117.3.1.2.8	Integer32	read-only	Sets the time a packet can live in the switch. This Lifetime Value (LV) is used as a parameter to calculate Switch Lifetime Limit (SLL) value. To calculate a valid SLL, the LV must be between 0 and 19, inclusive. If the LV value is greater than 19, the SLL is to be interpreted as infinite.
I32 ibSmaSwPortStateChange	1.3.6.1.3.117.3.1.2.9	Integer32	read-only	This object is set to 1 whenever the PortState component makes any of the following state changes in the link FSM: Down-->Initialize, Initialize-->Down, Armed-->Down, or Active-->Down Also, changes in PortState resulting from SubnSet IBA command do not change this bit. This object is set to 0 when the SMA writes a 1; writing a 0 is ignored.
I32 ibSmaSwLidsPerPort	1.3.6.1.3.117.3.1.2.10	Integer32	read-only	Specifies the number of LID/LMC combinations that may be assigned to a given external port for switches that support the Random Forwarding table.
I32 ibSmaSwPartitionEnforceNum	1.3.6.1.3.117.3.1.2.11	Integer32	read-only	Specifies the number of entries in the partition enforcement table per physical IBA port. The 0 value indicates that partition enforcement is not supported by the switch.
T/F ibSmaSwInboundEnforceCap	1.3.6.1.3.117.3.1.2.12	TruthValue	read-only	Flag that indicates whether the switch is capable of partition enforcement on received packets.
T/F ibSmaSwOutboundEnforceCap	1.3.6.1.3.117.3.1.2.13	TruthValue	read-only	Flag that indicates whether the switch is capable of partition enforcement on transmitted packets.
T/F ibSmaSwFilterRawPktInputCap	1.3.6.1.3.117.3.1.2.14	TruthValue	read-only	Flag to indicate whether the switch is capable of raw packet enforcement on received packets.
T/F ibSmaSwFilterRawPktOutputCap	1.3.6.1.3.117.3.1.2.15	TruthValue	read-only	Flag to indicate whether the switch is capable of raw packet enforcement on transmitted packets.
T/F ibSmaSwEnhancedPort0	1.3.6.1.3.117.3.1.2.16	TruthValue	read-only	Flag to indicate whether switch port 0 supports enhanced functions (TCA port). If false, switch port 0 is a base switch port 0.
ibSmaGuidInfo	1.3.6.1.3.117.3.1.3
ibSmaGuidInfoTable	1.3.6.1.3.117.3.1.3.1		not-accessible	A table containing SMA GUID information.
ibGuidInfoEntry	1.3.6.1.3.117.3.1.3.1.1		not-accessible	A conceptual row of the ibSmaGuidInfoTable containing information about a particular GUID entry.
IBD ibSmaGuidPortIndex	1.3.6.1.3.117.3.1.3.1.1.1	IbDataPort	not-accessible	Index that identifies IB port assoicated with this GUID table.
I32 ibSmaGuidIndex	1.3.6.1.3.117.3.1.3.1.1.2	Integer32	not-accessible	Index that identifies the GUID entry for this port. For any IB port there can be multiple 64 bit GUIDs assigned. The maximum number is implementationdependent. If the port does not have a GUID assigned to it, the row will have 1 entry with a 0 value.
IBG ibSmaGuidVal	1.3.6.1.3.117.3.1.3.1.1.3	IbGuid	read-only	The Global Unique Identifier (GUID) for this port entity.
ibSmaMgmtPortInfo	1.3.6.1.3.117.3.1.4
OCT ibSmaPortMKey	1.3.6.1.3.117.3.1.4.1	OCTET STRING	read-only	The 8-byte management key that is kept locally on each port. If the value is 0's, no authentication is done.
OCT ibSmaPortGidPrefix	1.3.6.1.3.117.3.1.4.2	OCTET STRING	read-only	GID prefix for this port.
I32 ibSmaPortLid	1.3.6.1.3.117.3.1.4.3	Integer32	read-only	The base LID of this port.
I32 ibSmaPortMasterSmLid	1.3.6.1.3.117.3.1.4.4	Integer32	read-only	The LID of the master SM that is managing this port.
T/F ibSmaPortIsSubnetManager	1.3.6.1.3.117.3.1.4.5	TruthValue	read-only	Capability flag for this node: Is Subnet Manager?
T/F ibSmaPortIsNoticeSupported	1.3.6.1.3.117.3.1.4.6	TruthValue	read-only	Capability flag for this node: Are Notices Supported?
T/F ibSmaPortIsTrapSupported	1.3.6.1.3.117.3.1.4.7	TruthValue	read-only	Capability flag for this node: Are IBA Traps Supported?
T/F ibSmaPortIsAutoMigrateSupported	1.3.6.1.3.117.3.1.4.8	TruthValue	read-only	Capability flag for this node: Is Automatic Migration Supported?
T/F ibSmaPortIsSlMappingSupported	1.3.6.1.3.117.3.1.4.9	TruthValue	read-only	Capability flag for this node: Is SL Mapping Supported?
T/F ibSmaPortIsMKeyNvram	1.3.6.1.3.117.3.1.4.10	TruthValue	read-only	Capability flag for this node: Is M_Key in NVRAM?
T/F ibSmaPortIsPKeyNvram	1.3.6.1.3.117.3.1.4.11	TruthValue	read-only	Capability flag for this node: Is P_Key in NVRAM?
T/F ibSmaPortIsLedInfoSupported	1.3.6.1.3.117.3.1.4.12	TruthValue	read-only	Capability flag for this node: Is LED Information Supported?
T/F ibSmaPortIsSmDisabled	1.3.6.1.3.117.3.1.4.13	TruthValue	read-only	Capability flag for this node: Is Subnet Manager Disabeld?
T/F ibSmaPortIsSysImgGuidSupported	1.3.6.1.3.117.3.1.4.14	TruthValue	read-only	Capability flag for this node: Is System Image GUID Supported?
T/F ibSmaPortIsPKeyExtPortTrapSup	1.3.6.1.3.117.3.1.4.15	TruthValue	read-only	Capability flag for this node: Is P_Key Switch External Port Trap supported?
T/F ibSmaPortIsCommManageSupported	1.3.6.1.3.117.3.1.4.16	TruthValue	read-only	Capability flag for this node: Is Communication Management Supported?
T/F ibSmaPortIsSnmpTunnelSupported	1.3.6.1.3.117.3.1.4.17	TruthValue	read-only	Capability flag for this node: Is SNMP Tunneling Supported?
T/F ibSmaPortIsReinitSupported	1.3.6.1.3.117.3.1.4.18	TruthValue	read-only	Capability flag for this node: Is Reinitialization Supported?
T/F ibSmaPortIsDevManageSupported	1.3.6.1.3.117.3.1.4.19	TruthValue	read-only	Capability flag for this node: Is Device Management Supported?
T/F ibSmaPortIsVendorClassSupported	1.3.6.1.3.117.3.1.4.20	TruthValue	read-only	Capability flag for this node: Is Vendor Class Supported?
T/F ibSmaPortIsDrNoticeSupported	1.3.6.1.3.117.3.1.4.21	TruthValue	read-only	Capability flag for this node: Is DR Notice Supported?
T/F ibSmaPortIsCapMaskNoticSupported	1.3.6.1.3.117.3.1.4.22	TruthValue	read-only	Capability flag for this node: Is Capability Mask Notice Supported?
T/F ibSmaPortIsBootMgmtSupported	1.3.6.1.3.117.3.1.4.23	TruthValue	read-only	Capability flag for this node: Is Boot Management Supported?
I32 ibSmaPortMKeyLeasePeriod	1.3.6.1.3.117.3.1.4.24	Integer32	read-only	Specifies the initial value of the lease period timer (in seconds). The lease period is the length of time that the M_Key Protection bits are to remain non-zero after a SubnSet(PortInfo) fails the M_Key authentication check. When the value is 0, the lease period shall never expire.
INT ibSmaPortMKeyProtectBits	1.3.6.1.3.117.3.1.4.25	INTEGER	read-only	Management Key (M_Key) protection bits. Management Key must have a non-zero value.
I32 ibSmaPortMasterSmSl	1.3.6.1.3.117.3.1.4.26	Integer32	read-only	The administrative Service Level of the master SM that is managing this port.
T/F ibSmaPortInitTypeLoad	1.3.6.1.3.117.3.1.4.27	TruthValue	read-only	The initialization type flags indicate the type of intialization requested by this port before SM moves it to Active or Armed state. Initialization Type flag: NoLoad. If the value is false(2), the attributes should be initialized. If the value is true(1), no data should be loaded into the attributes at all, asserting that the last-loaded data still exists and is valid.
T/F ibSmaPortInitTypeContent	1.3.6.1.3.117.3.1.4.28	TruthValue	read-only	Initialization Type flag: PreserveContent. If the value is false(2), the port makes no request regarding the content of the data that is loaded into its attributes. If it is true(1), the port is requesting that all such data, if loaded, be set to the most recent content loaded by the SM.
T/F ibSmaPortInitTypePresence	1.3.6.1.3.117.3.1.4.29	TruthValue	read-only	Initialization Type flag: PreservePresence. If the value is false(2), the port is requesting that all settable SA attributes referencing this port be removed prior to activating this port and Traps 64/65 be sent. If the value is true(1), the port is requesting that all such data be preserved, and that the traps not be sent.
T/F ibSmaPortInitTypeResuscitate	1.3.6.1.3.117.3.1.4.30	TruthValue	read-only	Initialization Type flag: DoNotResuscitate. If the value is false(2), ibSmaPortInitTypeLoad, ibSmaPortInitTypeContent, and ibSmaPortInitTypePresence ARE valid. If the value is true(1), ibSmaPortInitTypeLoad, ibSmaPortInitTypeContent, and ibSmaPortInitTypePresence ARE NOT valid. The port is requesting that reinitialization of this port and the in/out of service traps (64/65) be delayed until this flag is set to false(1).
T/F ibSmaPortInitNoLoadReply	1.3.6.1.3.117.3.1.4.31	TruthValue	read-only	The Init Reply flags are written by the SM prior to changing the port to Active or Armed state. Initialization Type Reply flag: NoLoadReply. If this value is false(2), the port attributes were initialized. If the value is true(1), no data was loaded into the port attributes.
T/F ibSmaPortInitPreserveContReply	1.3.6.1.3.117.3.1.4.32	TruthValue	read-only	Initialization Type flag: PreserveContentReply. If this value is false(2), no information is available regarding the content of the data loaded into the port attributes. If the value is true(1), the data loaded into the port attributes was set to the content most recently loaded by the SM.
T/F ibSmaPortInitPreservePresReply	1.3.6.1.3.117.3.1.4.33	TruthValue	read-only	Initialization Type Reply flag: PreservePresenceReply. If this value is false(2), all settable SA attributes referencing this port were removed prior to activating this port and the in/out service traps 64 and 65 were sent. If the value is true(1), all such data existing when this port was last active was not removed and the traps 64/65 were not sent.
G32 ibSmaPortMKeyViolations	1.3.6.1.3.117.3.1.4.34	Gauge32	read-only	Counts the number of SMP packets that have been received at this port that have invalid M_Keys. This object is a latching gauge, in that whenever the maximum gauge value is encounterd (i.e., the count reaches all 1's), the SMA must reset the gauge to 0, before this object begins incrementing its count again.
G32 ibSmaPortPKeyViolations	1.3.6.1.3.117.3.1.4.35	Gauge32	read-only	Counts the number of SMP packets that have been received at this port that have invalid P_Keys. This object is a latching gauge, in that whenever the maximum gauge value is encounterd (i.e., the count reaches all 1's), the SMA must reset the gauge to 0, before this object begins incrementing its count again.
G32 ibSmaPortQKeyViolations	1.3.6.1.3.117.3.1.4.36	Gauge32	read-only	Counts the number of SMP packets that have been received at this port that have invalid Q_Keys. This object is a latching gauge, in that whenever the maximum gauge value is encounterd (i.e., the count reaches all 1's), the SMA must reset the gauge to 0, before this object begins incrementing its count again.
I32 ibSmaPortNumGuid	1.3.6.1.3.117.3.1.4.37	Integer32	read-only	Number of GUID entries supported in the GUIDInfo attribute for this port.
I32 ibSmaPortSubnetTimeout	1.3.6.1.3.117.3.1.4.38	Integer32	read-only	Specifies the maximum expected subnet propagation delay, which depends upon the configuration of the switches, to reach any other port in the subnet and shall also be used to determine the maximum rate which SubnTraps() can be sent from this port by the SMA.
I32 ibSmaPortResponseTimeValue	1.3.6.1.3.117.3.1.4.39	Integer32	read-only	Specifies the expected maximum time between the port reception of a SMP and the transmission of the associated response.
ibSmaDataPortInfo	1.3.6.1.3.117.3.1.5
ibSmaPortInfoTable	1.3.6.1.3.117.3.1.5.1		not-accessible	A table containing SMA PortInfo information.
ibSmaPortInfoEntry	1.3.6.1.3.117.3.1.5.1.1		not-accessible	A conceptual row of the ibSmaPortInfoTable containing information about a particular data port and its attributes.
IBD ibSmaPortIndex	1.3.6.1.3.117.3.1.5.1.1.1	IbDataPort	not-accessible	Index that identifies the InfiniBand data port.
INT ibSmaPortLinkWidthEnabled	1.3.6.1.3.117.3.1.5.1.1.2	INTEGER	read-only	Enabled link width, indicated as follows: 0: No State Change (NOP) 1: 1x 2: 4x 3: 1x or 4x 8: 12x 9: 1x or 12x 10: 4x or 12x 11: 1x, 4x or 12x 4 - 7, 12 - 254: Reserved (Ignored) 255: Set to LinkWidthSupported value.
INT ibSmaPortLinkWidthSupported	1.3.6.1.3.117.3.1.5.1.1.3	INTEGER	read-only	Supported link width for this port. This is indicated as follows by the SMA: 1: 1x 3: 1x or 4x 11: 1x, 4x or 12x 0, 2, 4-10, 12-255: Reserved.
INT ibSmaPortLinkWidthActive	1.3.6.1.3.117.3.1.5.1.1.4	INTEGER	read-only	Currently active link width on this port. This is indicated as follows by the SMA: 1: 1x 2: 4x 8: 12x 0, 3, 4-7, 9-255: Reserved.
INT ibSmaPortLinkSpeedSupported	1.3.6.1.3.117.3.1.5.1.1.5	INTEGER	read-only	Supported link speed, indicated as follows: 1: 2.5Gbps 0, 2 - 15: reserved
INT ibSmaPortLinkState	1.3.6.1.3.117.3.1.5.1.1.6	INTEGER	read-only	The state of the link on this port. 0: No state change 1: Down (includes failed links) 2: Initialize 3: Armed 4: Active 5-15: Reserved
INT ibSmaPortPhysState	1.3.6.1.3.117.3.1.5.1.1.7	INTEGER	read-only	Physical Port State. Enumerated as: 0: No state change 1: Sleep 2: Polling 3: Disabled 4: PortConfigurationTraining 5: LinkUp 6: LinkErrorRecovery 7 - 15: Reserved
INT ibSmaPortLinkDownDefaultState	1.3.6.1.3.117.3.1.5.1.1.8	INTEGER	read-only	LinkDownDefault-State 0: No state change 1: Sleep 2: Polling 3-15: Reserved
I32 ibSmaPortLidMaskCount	1.3.6.1.3.117.3.1.5.1.1.9	Integer32	read-only	LID Mask Control count for multipath support for CA and router ports.
INT ibSmaPortLinkSpeedActive	1.3.6.1.3.117.3.1.5.1.1.10	INTEGER	read-only	Currently active link speed, indicated as follows: 1: 2.5Gbps 0, 2 - 15: reserved.
INT ibSmaPortLinkSpeedEnabled	1.3.6.1.3.117.3.1.5.1.1.11	INTEGER	read-only	Enabled link speed, indicated as follows: 0: No State Change (NOP) 1: 2.5 Gbps 2 - 14: Reserved (Ignored) 15: Set to LinkSpeedSupported value.
INT ibSmaPortNeighborMtu	1.3.6.1.3.117.3.1.5.1.1.12	INTEGER	read-only	Active maximum MTU enabled on this port for transmit: 1: 256 bytes 2: 512 bytes 3: 1024 bytes 4: 2048 bytes 5: 4096 bytes 0, 6 - 15: reserved
INT ibSmaPortVirtLaneSupport	1.3.6.1.3.117.3.1.5.1.1.13	INTEGER	read-only	Virtual Lane configuration supported on this port. Indicated as as follows by the SMA: 1: VL0 2: VL0, VL1 3: VL0 - VL3 4: VL0 - VL7 5: VL0 - VL14 0, 6 - 15: reserved.
I32 ibSmaPortVlHighPriorityLimit	1.3.6.1.3.117.3.1.5.1.1.14	Integer32	read-only	Limit of High Priority component of VL Arbitration Table. This object indicates the amount of high priority packets that can be trasnmitted wihout an opportunity to send a low priority packet. Specifically, the number of bytes that can be sent is this value times 4K bytes. A 255 value means the byte limit is unbounded and a value of 0 means that only a single packet from the high-priority table may be sent before an opportunity is given to the low- priority table.
I32 ibSmaPortVlArbHighCapacity	1.3.6.1.3.117.3.1.5.1.1.15	Integer32	read-only	VL/Weight pairs supported on this port in the VLArbitration table for high priority. Shall be 1 to 64 if more than one data VL is supported on this port, 0 otherwise.
I32 ibSmaPortVlArbLowCapacity	1.3.6.1.3.117.3.1.5.1.1.16	Integer32	read-only	VL/Weight pairs supported on this port in the VLArbitration table for low priority. Shall be N to 64 if more than one data VL is supported on this port, 0 otherwise, N being the number of data VLs supported.
INT ibSmaPortMtuCapacity	1.3.6.1.3.117.3.1.5.1.1.17	INTEGER	read-only	Maximum MTU supported by this port. 1: 256 bytes 2: 512 bytes 3: 1024 bytes 4: 2048 bytes 5: 4096 bytes 0, 6 - 15: reserved
I32 ibSmaPortVlStallCount	1.3.6.1.3.117.3.1.5.1.1.18	Integer32	read-only	Specifies the number of sequential packets dropped that causes the port to enter the VLStalled state. The result of setting this value to 0 is undefined.
I32 ibSmaPortHeadOfQueueLife	1.3.6.1.3.117.3.1.5.1.1.19	Integer32	read-only	Sets the time a packet can live at the head of a Virtual Lane queue. This variable (HL) is used to compute the Head of the Queue Lifetime Limit (HLL). It is used in the formula when the HL value is between 0 and 19, inclusive. When HL is greater than 19, the HLL is to be interpreted as infinite.
INT ibSmaPortOperationalVls	1.3.6.1.3.117.3.1.5.1.1.20	INTEGER	read-only	Virtual Lanes operational on this port, indicated as follows: 0: No change 1: VL0 2: VL0 - VL1 3: VL0 - VL3 4: VL0 - VL7 5: VL0 - VL14 6 - 15: reserved
T/F ibSmaPortPartEnforceInbound	1.3.6.1.3.117.3.1.5.1.1.21	TruthValue	read-only	Indicates support of optional inbound partition enforcement. If true, partition enforcement on packets received on this port is enabled. If false partition enforcement on packets received from this port is disabled.
T/F ibSmaPortPartEnforceOutbound	1.3.6.1.3.117.3.1.5.1.1.22	TruthValue	read-only	Indicates support of optional outbound partition enforcement. If true, partition enforcement on packets transmitted on this port is enabled. If false partition enforcement on packets transmitted from this port is disabled.
T/F ibSmaPortFilterRawPktInbound	1.3.6.1.3.117.3.1.5.1.1.23	TruthValue	read-only	Indicates support of optional inbound raw packet enforcement. If true, raw packets arriving on this port are discarded. If false, raw enforcement on packets received from this port is disabled.
T/F ibSmaPortFilterRawPktOutbound	1.3.6.1.3.117.3.1.5.1.1.24	TruthValue	read-only	Indicates support of optional outbound raw packet enforcement. If true, raw packets departing on this port are discarded. If false, raw enforcement on packets leaving from this port is disabled.
I32 ibSmaPortLocalPhysErrorThreshold	1.3.6.1.3.117.3.1.5.1.1.25	Integer32	read-only	Local Physical Error threshold value. When the count of marginal link errors exceeds this threshold, the local link integrity error shall be detected.
I32 ibSmaPortOverrunErrorThreshold	1.3.6.1.3.117.3.1.5.1.1.26	Integer32	read-only	Overrun error threshold value. When the count of buffer overruns over consecutive flow control update periods exceeds this threshold, the excessive buffer overrun error shall be detected.
ibSmaPKeyInfo	1.3.6.1.3.117.3.1.6
ibSmaPKeyTable	1.3.6.1.3.117.3.1.6.1		not-accessible	This table contains SMA Partition Key information for this port.
ibSmaPKeyEntry	1.3.6.1.3.117.3.1.6.1.1		not-accessible	A conceptual row of the ibPKeyTable containing information about the partition keys.
IBD ibSmaPKeyIBAPortIndex	1.3.6.1.3.117.3.1.6.1.1.1	IbDataPortAndInvalid	not-accessible	The IB data port index for the switch data ports. For switch management port 0 and for CAs and routers, the index value should be 255. This indicates that the entry is not referring to a valid switch data port. (In the IB attribute modifier the upper 16 bits indicate the data port, else it is 0).
I32 ibSmaPKeyIndex	1.3.6.1.3.117.3.1.6.1.1.2	Integer32	not-accessible	The 1-based entry Identifier for each Partition Key defined on a port. (The IB spec specifies 0..2047 blocks of 32 entries each for a total of 65,504 maximum entries, although the implemented limit is defined by PartitionCap for CAs, routers, and switch port 0, and by PartitionEnforcementCap for the switch data ports).
INT ibSmaPKeyMembership	1.3.6.1.3.117.3.1.6.1.1.3	INTEGER	read-only	If the P_Key type is limitedi(2), the switch may accept a packet with a matching full P_Key, but may not accept a packet with a matching limited key. If the P_Key type is full(3), the switch can accept packets with either a full or limited P_Key. If the P_Key type is none(1), there is no associated Key Base value.
I32 ibSmaPKeyBase	1.3.6.1.3.117.3.1.6.1.1.4	Integer32	read-only	15-bit base value of the P_Key that the switch will use to check against incoming packets.
ibSmaSlToVlMapInfo	1.3.6.1.3.117.3.1.7
ibSmaSL2VLMapTable	1.3.6.1.3.117.3.1.7.1		not-accessible	This table provides the virtual lane value for the output port/input port/service level mapping. Each output port contains a VL mapping for the next hop based on the input port the packet arrived on and its SL value.
ibSmaSL2VLMapEntry	1.3.6.1.3.117.3.1.7.1.1		not-accessible	Column definitions for the VL from output/input/SL entry.
IBD ibSmaIBAOutPortIndex	1.3.6.1.3.117.3.1.7.1.1.1	IbDataPortAndInvalid	not-accessible	The egress port index for the service level mapping. A value of 255 indicates the switch management port 0.
IBD ibSmaIBAInPortIndex	1.3.6.1.3.117.3.1.7.1.1.2	IbDataPortAndInvalid	not-accessible	The ingress port index for the service level mapping. A value of 255 indicates the switch management port 0.
I32 ibSmaServiceLevelIndex	1.3.6.1.3.117.3.1.7.1.1.3	Integer32	not-accessible	The (1-based) Service Level value index for this mapping.
I32 ibSmaVirtualLane	1.3.6.1.3.117.3.1.7.1.1.4	Integer32	read-only	The outgoing packet's Virtual Lane value for this Service Level Mapping.
ibSmaVLArbitInfo	1.3.6.1.3.117.3.1.8
ibSmaHiPriVlArbTable	1.3.6.1.3.117.3.1.8.1		not-accessible	This table provides visibility into the High Priority Arbitration process for configuring VL/Weight pairs for the IB data ports.
ibSmaHiPriVlArbEntry	1.3.6.1.3.117.3.1.8.1.1		not-accessible	Column definitions for High Priority Arbitration Table.
IBD ibSmaHiPriIBAPortIndex	1.3.6.1.3.117.3.1.8.1.1.1	IbDataPort	not-accessible	The index for the IBA port that is being configured.
I32 ibSmaHiPriNIndex	1.3.6.1.3.117.3.1.8.1.1.2	Integer32	not-accessible	The High Priority list index.
I32 ibSmaHiPriVirtLane	1.3.6.1.3.117.3.1.8.1.1.3	Integer32	read-only	The virtual lane this entry applies to.
I32 ibSmaHiPriWeight	1.3.6.1.3.117.3.1.8.1.1.4	Integer32	read-only	Number of 64-byte units that may be transmitted from this VL when its turn in the arbitration process occurs. A weight of 0 indicates that the entry should be skipped.
ibSmaLowPriVlArbTable	1.3.6.1.3.117.3.1.8.2		not-accessible	This table provides visibility into the Low Priority Arbitration process.
ibSmaLowPriVlArbEntry	1.3.6.1.3.117.3.1.8.2.1		not-accessible	Column definitions for Low Priority Arbitration Table.
IBD ibSmaLowPriIBAPortIndex	1.3.6.1.3.117.3.1.8.2.1.1	IbDataPort	not-accessible	The index for the IB data port that is being configured.
I32 ibSmaLowPriNIndex	1.3.6.1.3.117.3.1.8.2.1.2	Integer32	not-accessible	The Low Priority list index.
I32 ibSmaLowPriVirtLane	1.3.6.1.3.117.3.1.8.2.1.3	Integer32	read-only	The Virtual Lane this entry applies to.
I32 ibSmaLowPriWeight	1.3.6.1.3.117.3.1.8.2.1.4	Integer32	read-only	Number of 64-byte units that may be transmitted from this VL when its turn in the arbitration process occurs. A weight of 0 indicates that the entry should be skipped.
ibSmaLFTInfo	1.3.6.1.3.117.3.1.9
ibSmaLinForTable	1.3.6.1.3.117.3.1.9.1		not-accessible	A table containing information about the Linear Forwarding Table.
ibSmaLinForEntry	1.3.6.1.3.117.3.1.9.1.1		not-accessible	Current unicast forwarding Table entry configured by the Subnet Manager based on destination LID.
IBU ibSmaLinDestDLIDIndex	1.3.6.1.3.117.3.1.9.1.1.1	IbUnicastLid	not-accessible	Index that identifies Destination Local Identifier (DLID) that the forwarding entry refers to in the Linear Forwarding Table.
IBD ibSmaLinForwEgressPort	1.3.6.1.3.117.3.1.9.1.1.2	IbDataPortAndInvalid	read-only	The port to which packets with the LID corresponding to this entry are to be forwarded.
ibSmaRFTInfo	1.3.6.1.3.117.3.1.10
ibSmaRandomForwardingTable	1.3.6.1.3.117.3.1.10.1		not-accessible	A table containing SMA Random Forwarding information.
ibSmaRandomForwardingEntry	1.3.6.1.3.117.3.1.10.1.1		not-accessible	A conceptual row of the ibSmaRandomForwardingTable containing information about the Random Forwarding Table.
IBD ibSmaRandomForwardingPortIndex	1.3.6.1.3.117.3.1.10.1.1.1	IbDataPort	not-accessible	The port index value.
I32 ibSmaRandomDestLID	1.3.6.1.3.117.3.1.10.1.1.2	Integer32	read-only	Identifies Destination Local Identifier (DLID) that the forwarding entry refers to.
IBD ibSmaRandomForwEgressPort	1.3.6.1.3.117.3.1.10.1.1.3	IbDataPort	read-only	The port to which packets with the LID corresponding to this entry are to be forwarded.
I32 ibSmaRandomLMC	1.3.6.1.3.117.3.1.10.1.1.4	Integer32	read-only	The LID Mask Control (LMC) of this LID. The LMC specifies the number of Path Bits in the Local Identifier.
T/F ibSmaRandomIsValid	1.3.6.1.3.117.3.1.10.1.1.5	TruthValue	read-only	If true this LID/Port pair is valid. Note that when the SMA sets this parameter to 0, entries can be removed.
ibSmaMFTInfo	1.3.6.1.3.117.3.1.11
ibSmaMulForTable	1.3.6.1.3.117.3.1.11.1		not-accessible	A table containing information about the Multicast Forwarding Table.
ibSmaMulForEntry	1.3.6.1.3.117.3.1.11.1.1		not-accessible	Current multicast forwarding table entry as configured by the Subnet Manager based on destination LID.
IBM ibSmaMulDestDLIDIndex	1.3.6.1.3.117.3.1.11.1.1.1	IbMulticastLid	not-accessible	Identifies Destination Local Identifier (DLID) that the forwarding entry refers to in the Multicast Forwarding Table.
IBS ibSmaMulForwMask	1.3.6.1.3.117.3.1.11.1.1.2	IbSmPortList	read-only	A 256-bit mask that represents the port list. An incoming packet with this LID table entry will be forwarded to all ports for which the bit in the port mask is set to 1.
ibSmaSMInfo	1.3.6.1.3.117.3.1.12
ibSmaSubMgrInfo	1.3.6.1.3.117.3.1.12.1
ibSmaSmInfoTable	1.3.6.1.3.117.3.1.12.1.1		not-accessible	A table containing SMA Subnet Manager information.
ibSmaSmInfoEntry	1.3.6.1.3.117.3.1.12.1.1.1		not-accessible	A conceptual row of the ibSmaSmInfoTable containing information about the Subnet Manager Table.
IBD ibSmaSmInfoPortIndex	1.3.6.1.3.117.3.1.12.1.1.1.1	IbDataPort	not-accessible	The port index value.
IBG ibSmaSmGuid	1.3.6.1.3.117.3.1.12.1.1.1.2	IbGuid	read-only	The Port GUID of the port where the SM resides.
OCT ibSmaSmSmKey	1.3.6.1.3.117.3.1.12.1.1.1.3	OCTET STRING	read-only	Key for this SM. This is shown as zeroes unless the requesting SM is proven to be the master, or the requester is otherwise authenticated.
C32 ibSmaSmSmpCountEx	1.3.6.1.3.117.3.1.12.1.1.1.4	Counter32	read-only	Counter that increments each time the SM issues an SMP or performs other management activities. This counter is used as a heartbeat indicator by standby SMs.
I32 ibSmaSmPriority	1.3.6.1.3.117.3.1.12.1.1.1.5	Integer32	read-only	Administratively assigned priority for this SM. This can be reset by master SM. 0 is the lowest priority. An out-of-band mechanism shall be provided to set this value. The default value shall be 0.
INT ibSmaSmState	1.3.6.1.3.117.3.1.12.1.1.1.6	INTEGER	read-only	Enumerated value indicating this SM's state. The InfiniBand enumeration values are: 0 - not active 1 - discovering 2 - standby 3 - master 4-15 - reserved. Note: a value of reserved returns unknown(1).
ibSmaVendDiagInfo	1.3.6.1.3.117.3.1.13
ibSmaVendDiagInfoTable	1.3.6.1.3.117.3.1.13.1		not-accessible	A table containing SMA Vendor Diagnostic Info information.
ibSmaVendDiagInfoEntry	1.3.6.1.3.117.3.1.13.1.1		not-accessible	A conceptual row of the ibSmaVendDiagInfoTable containing information about a particular data port's diagnostic status.
IBD ibSmaVendDiagPortIndex	1.3.6.1.3.117.3.1.13.1.1.1	IbDataPortAndInvalid	not-accessible	Index that identifies the port for the diagnostics. If the index value is 255, information about the management port is returned.
INT ibSmaPortGenericDiagCode	1.3.6.1.3.117.3.1.13.1.1.2	INTEGER	read-only	The generic portion of the Port Info Diagnostic code.
I32 ibSmaPortVendorDiagCode	1.3.6.1.3.117.3.1.13.1.1.3	Integer32	read-only	The vendor specific portion of the Port Info Diagnostic code.
T/F ibSmaPortVendorDiagIndexFwd	1.3.6.1.3.117.3.1.13.1.1.4	TruthValue	read-only	Flag to control ibSmaPortVendorDiagData data buffer. If this boolean is true(1), the data buffer contains meaningful vendor-supplied additional diagnostic information. If this object is false(2), the buffer is empty.
OCT ibSmaPortVendorDiagData	1.3.6.1.3.117.3.1.13.1.1.5	OCTET STRING	read-only	Data buffer that can contain additional vendor-specific diagnostic information. The ibSmaPortVendorDiagIndexFwd flag controls whether this object contains meaningful data. Note: in IB, this buffer comprises n number of 62 byte buffers. This object defines a buffer that can hold up to 2 of these IB chained buffers.
ibSmaLedInfo	1.3.6.1.3.117.3.1.14
ibSmaLedInfoTable	1.3.6.1.3.117.3.1.14.1		not-accessible	A table containing SMA LED Info information.
ibSmaLedInfoEntry	1.3.6.1.3.117.3.1.14.1.1		not-accessible	A conceptual row of the ibSmaLedInfoTable containing information about a particular data port's LED status.
IBD ibSmaLedIndex	1.3.6.1.3.117.3.1.14.1.1.1	IbDataPort	not-accessible	Index that identifies the IB data port that can have an LED associated with it.
INT ibSmaLedState	1.3.6.1.3.117.3.1.14.1.1.2	INTEGER	read-only	State of the LED.
ibSmaNotifications	1.3.6.1.3.117.3.2
ibSmaNotificationPrefix	1.3.6.1.3.117.3.2.0
NTF ibSmaPortLinkStateChange	1.3.6.1.3.117.3.2.1			This notification translates InfiniBand SMA Trap 128: Link State of at least one port of switch at has changed.
NTF ibSmaLinkIntegrityThresReached	1.3.6.1.3.117.3.2.2			This notification translates InfiniBand SMA Trap 129: Local Link Integrity threshold reached at .
NTF ibSmaExcessBuffOverrunThres	1.3.6.1.3.117.3.2.3			This notification translates InfiniBand SMA Trap 130: Exccessive Buffer Overrun threshold reached at .
NTF ibSmaFlowCntrlUpdateTimerExpire	1.3.6.1.3.117.3.2.4			This notification translates InfiniBand SMA Trap 131: Switch Flow Control Update watchdog timer expired at .
NTF ibSmaCapabilityMaskModified	1.3.6.1.3.117.3.2.5			This notification translates InfiniBand SMA Trap 144: The capability mask at has been modified to .
NTF ibSmaSysImageGuidModified	1.3.6.1.3.117.3.2.6			This notification translates InfiniBand SMA Trap 145: The System Image GUID at has been modified to .
NTF ibSmaBadManagementKey	1.3.6.1.3.117.3.2.7			This notification translates InfiniBand SMA Trap 256: Bad M_Key, from attempted with and .
NTF ibSmaBadPartitionKey	1.3.6.1.3.117.3.2.8			This notification translates InfiniBand SMA Trap 257: Bad P_Key, from // to // on .
NTF ibSmaBadQueueKey	1.3.6.1.3.117.3.2.9			This notification translates InfiniBand SMA Trap 258: Bad Q_Key, from // to // on .
NTF ibSmaBadPKeyAtSwitchPort	1.3.6.1.3.117.3.2.10			This notification translates InfiniBand SMA Trap 259: Bad P_Key, from // to // on at switch external port , where the validity of the fields is indicated by .
ibSmaConformance	1.3.6.1.3.117.3.3
ibSmaCompliances	1.3.6.1.3.117.3.3.1
ibSmaBasicNodeCompliance	1.3.6.1.3.117.3.3.1.1			The basic node implementation requirements for agents that support the IPOIB SMA MIB.
ibSmaFullSwitchCompliance	1.3.6.1.3.117.3.3.1.2			The full node implementation requirements for agents that support the IPOIB SMA MIB for InfiniBand switches.
ibSmaFullRouterCACompliance	1.3.6.1.3.117.3.3.1.3			The full node implementation requirements for agents that support the IPOIB SMA MIB for InfiniBand CAs and routers.
ibSmaGroups	1.3.6.1.3.117.3.3.2
ibSmaNodeGroup	1.3.6.1.3.117.3.3.2.1			The ibSmaNodeGroup defines the MIB objects that describe this InfiniBand subnet node.
ibSmaSwitchGroup	1.3.6.1.3.117.3.3.2.2			The ibSmaSwitchGroup defines the MIB objects that describe this InfiniBand switch.
ibSmaGuidGroup	1.3.6.1.3.117.3.3.2.3			The ibSmaGuidGroup defines the MIB object that describes the GUIDs associated with this node.
ibSmaMgmtPortGroup	1.3.6.1.3.117.3.3.2.4			The ibSmaMgmtPortGroup defines the MIB objects that describe the management port.
ibSmaDataPortGroup	1.3.6.1.3.117.3.3.2.5			The ibSmaDataPortGroup defines MIB objects for IB data ports.
ibSmaPKeyGroup	1.3.6.1.3.117.3.3.2.6			The ibSmaPKeyGroup defines the MIB objects that describe the Partition Keys.
ibSmaSlToVlMapGroup	1.3.6.1.3.117.3.3.2.7			The ibSmaSlToVlMapGroup defines the MIB objects that describe the Service Level to Virtual Lane mapping.
ibSmaVLArbitGroup	1.3.6.1.3.117.3.3.2.8			The ibSmaVLArbitGroup defines the MIB objects that describe the Virtual Lane High and Low Arbitrations.
ibSmaLFTGroup	1.3.6.1.3.117.3.3.2.9			The ibSmaLFTGroup defines the MIB objects that describe the Linear Forwarding Table.
ibSmaRFTGroup	1.3.6.1.3.117.3.3.2.10			The ibSmaRFTGroup defines the MIB objects that describe the Random Forwarding Table.
ibSmaMFTGroup	1.3.6.1.3.117.3.3.2.11			The ibSmaMFTGroup defines the MIB objects that describe the Multicast Forwarding Table.
ibSmaSMGroup	1.3.6.1.3.117.3.3.2.12			The ibSmaSMGroup defines the MIB objects that describe the Subnet Manager Information Table.
ibSmaVendDiagGroup	1.3.6.1.3.117.3.3.2.13			The ibSmaVendDiagGroup defines the MIB objects that describe the vendor diagnostics table.
ibSmaLedGroup	1.3.6.1.3.117.3.3.2.14			The ibSmaSMGroup defines the MIB objects that describe the LED table.
ibSmaNotificationsGroup	1.3.6.1.3.117.3.3.2.15			The notifications that an IPOIB SNMP agent transmits on the behalf of the SMA Trap message implementation.

RFC description

InfiniBand Subnet Management Agent (SMA) instrumentation for IP over InfiniBand (IPoIB) management and monitoring.

Start monitoring InfiniBand fabric equipment, Subnet Management Agent (node/port identity and SMA addressing status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SMA-MIB