RS-XX8000-DVB-TX-MIB

All MIBs › RS-XX8000-DVB-TX-MIB

Organization: Rohde&Schwarz GmbH & Co. KG

Last Updated: 2012-11-01

Category: Broadcast and Media

Description: Manages DVB-T transmitter configuration, RF parameters, and status for Rohde and Schwarz SX8000.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RS-XX8000-DVB-TX-MIB?

RS-XX8000-DVB-TX-MIB is a Rohde & Schwarz proprietary MIB (companion to RS-COMMON-MIB/RS-XX8000-COMMON-MIB) for the XX8000/NetCCU800 series DVB television transmitter systems, covering SingleTx, DualDrive, and Active/Passive Reserve redundancy configurations. Its command table exposes transmitter-control actions — reset summary fault, load/save/re-save parameter sets, switch between program and reserve operation mode, select automatic exciter/output-stage mode, RF switch control, and per-exciter automatic-input-mode/preselect commands. As a hardware-control/status MIB it lets a broadcast engineer remotely switch a DVB transmitter between primary and reserve exciters/output stages and clear fault conditions. It is deployed on Rohde & Schwarz XX8000/NetCCU800 series DVB transmitter systems. Engineers can download the RS-XX8000-DVB-TX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RS-XX8000-DVB-TX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Rohde & Schwarz XX8000/NetCCU800 series DVB transmitter systems

Monitoring Examples

A broadcast engineer issues cmdTxOperationModeReserve to fail a DVB transmitter over to its reserve exciter/output stage during scheduled maintenance on the primary chain, then confirms fault state via cmdTxResetSumFault once maintenance completes.

What Can Be Monitored

transmitter operation mode
fault/reserve switchover status

Imported Objects

From RS-XX8000-COMMON-MIB

EqualizerCalibrationState
EventClass
EventMask
EventMaxEntryNumber
EventPriority
EventState
FailDelayMode
FailDelayStatus
FloatingPoint
IndexAB
IndexAmplifier
IndexRack
InputSource
LogbookEntryMessagesExcTv
LogbookEntryMessagesNetCCU
LogbookEntryMessagesOST
LogbookEntrySlope
LogbookMaxEntryNumber
ProdInfoModuleNameTv
ReadableString
SwitchOnOff
Sx801AmplifierState
TimeOfDay
Trigger
TvStandard
eventAlarmClass	OBJECT-TYPE
eventAlarmPriority	OBJECT-TYPE
eventEvent	OBJECT-TYPE
indexAB	OBJECT-TYPE
indexAmplifier	OBJECT-TYPE
indexRack	OBJECT-TYPE
rsXx8000	OBJECT-IDENTITY
rsXx8000MibModule	MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
rsXx8000DvbTx	1.3.6.1.4.1.2566.127.1.2.167.4			Xx8000 DVB transmitter.
rsXx8000DvbTxObjs	1.3.6.1.4.1.2566.127.1.2.167.4.1
commandsTxTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.1		not-accessible	This table contains important commands for the transmitter.
commandsTxEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1		not-accessible	An entry for a designated transmitter and device.
TRI cmdTxResetSumFault	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.1	Trigger	read-write	Reset all faults (in all modules) of the transmitter. You reset a designated transmitter (NetCCU, Exciters, Outputstages). An equivalent would be pressing RESET at this transmitters frontpanel. A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
I32 cmdTxParametersetLoad	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.2	Integer32	read-write	This loads the desired parameter set.
I32 cmdTxParametersetSave	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.3	Integer32	read-write	This saves the current settings to a designated parameter set.
TRI cmdTxParametersetReSave	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.4	Trigger	read-write	This saves the changes to the current parameter set.
SWI cmdTxOperationModeProgram	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.5	SwitchOnOff	read-write	This switches the program path of the transmitter on/off.
SWI cmdTxOperationModeReserve	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.6	SwitchOnOff	read-write	This switches the reserve path of the transmitter on/off.
SWI cmdTxOpModeExcAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.7	SwitchOnOff	read-write	This switches the exciter automatic on/off.
SWI cmdTxOpModeOstAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.8	SwitchOnOff	read-write	This switches the outputstage automatic on/off. This paramter is only available for systems with an automatic output switch.
IND cmdTxPreselectExciter	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.9	IndexAB	read-write	This sets exciterA or exciterB to program path (antenna) of the transmitter.
INT cmdTxPreselectOutputstage	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.10	INTEGER	read-write	This sets - outputstageA or - outputstageB or - both to program path (antenna) of the transmitter, or it sets both to dummyload. The settings bothToAntenna(3) and bothToDummyLoad(4) are only settable for ActiveReserve systems. This paramter is only available for systems with an automatic output switch.
I32 cmdTxDelayTimeExcAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.11	Integer32	read-write	This sets the exciter automatic delay time.
I32 cmdTxDelayTimeOstAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.12	Integer32	read-write	This sets the outputstage automatic delay time. This paramter is only available for systems with an automatic output switch.
INT cmdTxRfSwitch	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.13	INTEGER	read-write	RF switch for single-ended systems.
TVS cmdTxSystemMode	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.15	TvStandard	read-write	This object gives you the possibility of switching the TV standard of a whole system with NetCCU with only one command. Not applicable for N+1 or NTx systems. The value 'test' cannot be written.
SWI cmdTxProgramExciterPrio	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.20	SwitchOnOff	read-write	Enables/Disables priority usage of program exciter
TRI cmdTxChangeOver	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.21	Trigger	read-write	Performs a change over
INT cmdTxSwitchPosition	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.22	INTEGER	read-only	Shows the actual switch position. The program exciter is connected to input 1 (RF IN 1), the control exciter is connected to input 2 (RF IN 2) of the base amplifier.
IND cmdDeviceIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.30	IndexAB	not-accessible	This column is used to show parameters for both exiters, if you have dualdrive transmitters.
SWI cmdExcOpModeInputAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.31	SwitchOnOff	read-write	Activates/deactivates the input automatic. If input automatic is active and a loss of input signal is detected on the current input the reserve input will be used instead.
INT cmdExcPreselectInput	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.32	INTEGER	read-write	This sets the preselection of a transmitters input.
INT cmdExcMode	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.33	INTEGER	read-write	Switch between DVB-T and DVB-H.
INT cmdExcNetworkMode	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.34	INTEGER	read-write	Switch between Single Frequency Networks (SFN) and Multiple Frequency Networks (MFN).
INT cmdExcTPSSource	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.35	INTEGER	read-write	Transmitted TPS parameters can be adjusted manually inside the transmitter or automatically via MIP from the SFN adaptor.
SWI cmdExcEnableCellID	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.36	SwitchOnOff	read-write	This enables the Cell ID insertion. The length indicator will be adjusted.
I32 cmdExcTxAddress	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.37	Integer32	read-write	This is the unique address of the transmitter to reference specific settings in the MIP.
SWI cmdExcTxAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.38	SwitchOnOff	read-write	This enables Tx specific parameters from the MIP data caroussel (e.g. time offset, frequency offset).
SWI cmdExcInputAutoSwitch	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.39	SwitchOnOff	read-write	Activates/deactivates the input automatic. If input automatic is active and a loss of input signal is detected on the current input the reserve input will be used instead. This object is deprecated. It's recommended to use cmdExcOpModeInputAutomatic instead.
SWI cmdExcInputSeamless	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.40	SwitchOnOff	read-write	If the datastreams on both inputs are syncronised a seamless switch is possible. With this parameter the seamless switch can be suppressed to enable a check of the input automatic.
INT cmdExcInputPriority	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.41	INTEGER	read-write	Equal: There are no differences between both inputs. If a failure on the current input is detected it will be switched to the reserve input. It stays there until the reserve shows a failure. Prior: Whenever possible a certain input shall be used. If a failure is detected the reserve will be used as short as possible.
I32 cmdExcInputCheckTimeForward	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.42	Integer32	read-write	This time has to elapse before the current input switches to the reserve input.
I32 cmdExcInputCheckTimeSwitchback	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.43	Integer32	read-write	This time has to elapse before the automatic switches back from the reserve to a preselected input. This value has no effect if the priority is set to equal.
INT cmdExcInputMuteOnFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.44	INTEGER	read-write	If a loss of input signal is detected, the exciter mutes.
INT cmdExcInputManualPreseletionHP1	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.45	INTEGER	read-write	The data format of the input can be detected automatically or can be set manually to ASI or SMPTE.
INT cmdExcInputManualPreseletionHP2	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.46	INTEGER	read-write	The data format of the input can be detected automatically or can be set manually to ASI or SMPTE.
INT cmdExcInputManualPreseletionLP1	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.47	INTEGER	read-write	The data format of the input can be detected automatically or can be set manually to ASI or SMPTE.
INT cmdExcInputManualPreseletionLP2	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.48	INTEGER	read-write	The data format of the input can be detected automatically or can be set manually to ASI or SMPTE.
INT cmdExcTPSManualBandwidth	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.49	INTEGER	read-write	The bandwidth used by the RF channel.
INT cmdExcTPSManualFFTLength	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.50	INTEGER	read-write	The used FFT length (depends on the DVB network).
INT cmdExcTPSManualGuardInterval	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.51	INTEGER	read-write	The Guard interval affects the error correction in multipath receiving situations. A long Guard Interval reduces the amount of payload data.
INT cmdExcTPSManualConstellation	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.52	INTEGER	read-write	This parameter sets the modulation mode.
INT cmdExcTPSManualAlpha	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.53	INTEGER	read-write	An alpha greater than noHierarchy(1) enables the hierarchical coding mode.
I32 cmdExcTPSManualCellID	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.54	Integer32	read-write	Via Cell ID the receiver knows the current network.
INT cmdExcTPSManualInterleaver	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.55	INTEGER	read-write	Enables the bit interleaver for hierarchical coding
INT cmdExcTPSManualCoderateHP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.56	INTEGER	read-write	The Code Rate sets the ratio between payload and error correction information.
INT cmdExcTPSManualCoderateLP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.57	INTEGER	read-write	The Code Rate sets the ratio between payload and error correction information.
SWI cmdExcTPSManualTimeSlicingHP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.58	SwitchOnOff	read-write	Enables the time slicing for hierarchical coding.
SWI cmdExcTPSManualTimeSlicingLP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.59	SwitchOnOff	read-write	Enables the time slicing for hierarchical coding.
SWI cmdExcTPSManualFECHP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.60	SwitchOnOff	read-write	Enables the forward error correction (FEC) for hierarchical coding.
SWI cmdExcTPSManualFECLP	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.61	SwitchOnOff	read-write	Enables the forward error correction (FEC) for hierarchical coding.
NUM cmdExcSFNStaticDelay	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.62	FloatingPoint	read-write	A constant adjustable delay for tuning a SFN (-999999.9 ... 999999.9).
I32 cmdExcSFNDeviationTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.63	Integer32	read-write	Leap In Time. This parameter sets the deviation in time when a readjustment of the dynamic delay is necessary.
I32 cmdExcFrequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.64	Integer32	read-write	This is the RF frequency.
INT cmdExcReferenceSource	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.65	INTEGER	read-write	The Source of the reference signal. The value internGPS is not valid for SX800.
INT cmdExcMuteOnPPSFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.66	INTEGER	read-write	Select the behaviour if the external second pulse is not available.
INT cmdExcMuteOnReferenceFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.67	INTEGER	read-write	Select the behaviour if the external reference is not available.
I32 cmdExcRefFailDelayTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.68	Integer32	read-write	Adjusts the time after the RF will be muted in case of a reference problem. Zero hours means react immediately.
INT cmdExcTypeLossOfInput	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.69	INTEGER	read-write	If the input signal is lost, either a warning or a fault can be generated. If you select fault here, a switchover to the reserve exciter will be executed when input signal is lost.
SWI cmdExcRfOutput	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.70	SwitchOnOff	read-write	Turns on/switches off the output signal. This switch takes the same effect as the switch on the frontpanel of the exciter.
SWI cmdExcRfOutputRegulation	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.71	SwitchOnOff	read-write	Turns on/switches off the automatic output level regulation.
NUM cmdExcRfOutputManualRfLevel	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.72	FloatingPoint	read-write	Adjusts the RF level (0.0 ... 100.0). The value relates to an attenuation of 0 dB.
I32 cmdExcRfOutputAttenuation	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.73	Integer32	read-write	Activates internal attenuators to reduce the output level of the exciter. Adjustable in steps of 3 dB only.
NUM cmdExcRfOutputRfSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.74	FloatingPoint	read-write	Adjusts a slope in the RF signal (-50.0 ... 50.0).
NUM cmdExcRfOutputModulationSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.75	FloatingPoint	read-write	Modulation slope (-50.0 ... 50.0).
INT cmdExcRfIqAdjustStart	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.77	INTEGER	read-write	Starts the automatic IQ adjustment. It works for the current used local 1 frequency and lasts up to 5 minutes. In this time the output will be muted. During the adjustment no transmitter parameter shall be changed. Break will stop the automatic immediately. The IQ modulator looses its adjustment! Read values mean idle(1) and started(2).
SWI cmdExcRfIqAdjustTestsignal	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.78	SwitchOnOff	read-write	Generates a test signal to adjust the IQ modulation. It is necessary to disconnect the rf-cable to the output stages.
I32 cmdExcRfIqAdjustBiasCoarseI	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.79	Integer32	read-write	Adjusts the offset for I in huge steps.
I32 cmdExcRfIqAdjustBiasCoarseQ	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.80	Integer32	read-write	Adjusts the offset for Q in huge steps.
I32 cmdExcRfIqAdjustBiasFineI	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.81	Integer32	read-write	Adjusts the offset for I in small steps.
I32 cmdExcRfIqAdjustBiasFineQ	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.82	Integer32	read-write	Adjusts the offset for Q in small steps.
I32 cmdExcRfIqAdjustGainI	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.83	Integer32	read-write	Adjusts the gain for I in small steps.
I32 cmdExcRfIqAdjustGainQ	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.84	Integer32	read-write	Adjusts the gain for Q in small steps.
NUM cmdExcRfIqAdjustPhase	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.85	FloatingPoint	read-write	Adjusts the phase between I and Q (-14.000 ... 14.000).
INP cmdExcInput1Source	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.86	InputSource	read-write	Source for input 1.
INP cmdExcInput2Source	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.87	InputSource	read-write	Source for input 2.
SWI cmdExcInpAutoReadyAfterChangeOv	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.88	SwitchOnOff	read-write	Input automatic ready after change over.
I32 cmdExcInputFailDelayTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.89	Integer32	read-write	The time between detecting a loss of input signal and displaying a failure.
INT cmdExcTransmitterType	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.90	INTEGER	read-write	the TV standard of the transmitter The transmitter is rebooted automatically when the TV standard is changed. Signal processing is also switched over.
SWI cmdExcTimeScheduler	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.91	SwitchOnOff	read-write	If on, the time scheduler controls the tx type. When switching on the scheduler it may instantly set the correct TV standard and reboot the device.
INT cmdExcMuteCondition	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.92	INTEGER	read-write	When notBeforeSyncLoss(2) is selected, it relativizes the cmdExcInputMuteOnFail setting mute(1): If a DVB receiver is the last valid input, an existing transport stream, even if it is faulty shall not be muted. Only for SLx/Sx801
NUM cmdExcRfWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.97	FloatingPoint	read-write	Warning limit for the RF control. min: -15.0, max: 0.0
NUM cmdExcRfFailLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.98	FloatingPoint	read-write	Fault limit for the RF control. min: -15.0, max: 0.0
NUM cmdExcOutputPower	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.99	FloatingPoint	read-write	amplifier output power 0 ... 400 W
NUM cmdOstRefVoltageVision	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.100	FloatingPoint	read-write	This adjusts the output power of the amplifier. This value is settable with maximal 1 position after point (example 11.2).
I32 cmdOstMaxOutletTempThreshold	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.101	Integer32	read-write	This sets the threshold for the outlet temperature.
INT cmdExcMonitoringOutput	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.110	INTEGER	read-write	Selects which signal appears at the monitoring output.
I32 cmdExcOcxoAdjust	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.111	Integer32	read-write	Adjusts the frequency of the internal 10 MHz reference. This value only takes effect if the reference source 'internal' is selected.
SWI cmdExcExpectInputReserve	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.112	SwitchOnOff	read-write	If on(1) the warning txExcInputReseveMissing will be generated in case second input is missing.
SWI cmdExcEnablePcrReset	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.113	SwitchOnOff	read-write	Enables/disables daily PCR resets. This option is valid only in MFN operation. The reset time is given in cmdExcTimeForDailyPcrReset.
TIM cmdExcTimeForDailyPcrReset	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.114	TimeOfDay	read-write	Sets the time of day for daily PCR reset.
FAI cmdExcFailDelayMode	1.3.6.1.4.1.2566.127.1.2.167.4.1.1.1.115	FailDelayMode	read-write	Condition when the fail delay time is used.
summaryInfo	1.3.6.1.4.1.2566.127.1.2.167.4.1.2
T/F summaryFaultTx	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.1	TruthValue	read-only	This indicates a summary fault of the transmitter. true(1) --> summary fault false(2) --> no summary fault There is a fault of at least one module (e.g. Exciter) which causes this summary fault. An equivalent would be the LED Fault at the transmitters frontpanel.
T/F summaryWarningTx	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.2	TruthValue	read-only	This indicates a summary warning of the transmitter. true(1) --> summary warning false(2) --> no summary warning There is a fault of at least one module (e.g. Exciter) which causes this summary warning. An equivalent would be the LED Warning at the transmitters frontpanel.
T/F localModeTx	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.3	TruthValue	read-only	This indicates the local/remote-mode of the transmitter. true(1) --> local false(2) --> remote The transmitter is eigther in local-mode or in remote-mode. For security reasons it is not possible to set this value! An equivalent would the LED Local at the transmitters frontpanel.
T/F rfOnTx	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.4	TruthValue	read-only	The RF is present for the corresponding transmitter.
NUM forwardPower	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.5	FloatingPoint	read-only	The measured forwarded power [W] of the transmitter. For Active Reserve systems it is the sum of both outputstages.
NUM reflectedPower	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.6	FloatingPoint	read-only	The measured reflected power [W] of the transmitter. For Active Reserve systems it is the sum of both outputstages. Not available for lowpower systems.
T/F summaryFaultExcA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.7	TruthValue	read-only	This indicates a summary fault of exciter.
T/F summaryFaultOstA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.8	TruthValue	read-only	This indicates a summary fault of outputstage.
T/F summaryFaultExcB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.9	TruthValue	read-only	This indicates a summary fault of exciter.
T/F summaryFaultOstB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.10	TruthValue	read-only	This indicates a summary fault of outputstage.
T/F exciterAutomaticReady	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.11	TruthValue	read-only	The Exciter Automatic is Ready. In case of any fault on one exciter, there will be a switchover to the other exciter.
T/F exciterAutomaticChanged	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.12	TruthValue	read-only	The Exciter Automatic has changed. There was a fault on one exciter which lead to this changeover.
T/F exciterAutomaticFault	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.13	TruthValue	read-only	The Exciter Automatic is faulty. In case of any fault on one exciter, there will be no switchover to the other exciter, because of this fault.
T/F outputstageAutomaticReady	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.14	TruthValue	read-only	The Outputstage Automatic is Ready. In case of any fault on one outputstage, there will be a switchover to the other outputstage. This paramter is only available for systems with an automatic output switch.
T/F outputstageAutomaticChanged	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.15	TruthValue	read-only	The Outputstage Automatic has changed. There was a fault on one outputstage which lead to this changeover. This paramter is only available for systems with an automatic output switch.
T/F outputstageAutomaticFault	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.16	TruthValue	read-only	The Outputstage Automatic is faulty. In case of any fault on one outputstage, there will be no switchover to the other outputstage, because of this fault. This paramter is only available for systems with an automatic output switch.
T/F noConnectionExcA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.17	TruthValue	read-only	No Connection between NetCCU and Exciter.
T/F noConnectionOstA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.18	TruthValue	read-only	No Connection between NetCCU and Outputstage.
T/F noConnectionExcB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.19	TruthValue	read-only	No Connection between NetCCU and Exciter.
T/F noConnectionOstB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.20	TruthValue	read-only	No Connection between NetCCU and Outputstage.
T/F activeExcA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.21	TruthValue	read-only	ExciterA is currently active.
T/F activeOstA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.22	TruthValue	read-only	OutputstageA is currently active.
T/F activeExcB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.23	TruthValue	read-only	ExciterB is currently active.
T/F activeOstB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.24	TruthValue	read-only	OutputstageB is currently active.
NUM forwardPowerOstA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.25	FloatingPoint	read-only	The measured forwarded power [W] of the OutputstageA.
NUM reflectedPowerOstA	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.26	FloatingPoint	read-only	The measured reflected power [W] of the OutputstageA. Not available for lowpower systems.
NUM forwardPowerOstB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.27	FloatingPoint	read-only	The measured forwarded power [W] of the OutputstageB.
NUM reflectedPowerOstB	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.28	FloatingPoint	read-only	The measured reflected power [W] of the OutputstageB. Not available for lowpower systems.
NUM powerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.29	FloatingPoint	read-only	Monitoring value of the output voltages of the power supply.
T/F additionalPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.30	TruthValue	read-only	Shows whether the NetCCU has an additional (external) power supply.
NUM internalPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.31	FloatingPoint	read-only	Monitoring value of the output voltages of the internal power supply.
NUM externalPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.2.32	FloatingPoint	read-only	Monitoring value of the output voltages of the external power supply.
detailedInfo	1.3.6.1.4.1.2566.127.1.2.167.4.1.3
excInputTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2		not-accessible	A table for more detailed information about the exciter. These values are all read-only. For settings, refer to commands.
excInputEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1		not-accessible	An entry for a designated input channel.
IND excInputExcIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.1	IndexAB	not-accessible	The index for exciterA (and exciterB if there are DualDrive systems).
I32 excInputChannelIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.2	Integer32	not-accessible	The index for the different input channels.
INT excInputChannelName	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.3	INTEGER	read-only	This is the logical name for the index for the different input channels.
T/F excInputConnected	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.4	TruthValue	read-only	The input channel is connected.
T/F excInputSeamless	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.5	TruthValue	read-only	The input channel is in seamless mode.
T/F excInputPreselected	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.6	TruthValue	read-only	The input channel is the preselected.
T/F excInputActive	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.7	TruthValue	read-only	The input channel is active.
T/F excInputMipFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.8	TruthValue	read-only	Input channel MIP fail.
INT excInputBandwidth	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.9	INTEGER	read-only	The bandwidth used by the input channel.
INT excInputFFTLength	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.10	INTEGER	read-only	The used FFT length (depends on the DVB network).
INT excInputGuardInterval	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.11	INTEGER	read-only	The Guard interval affects the error correction in multipath receiving situations. A long Guard Interval reduces the amount of payload data.
INT excInputConstellation	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.12	INTEGER	read-only	This parameter sets the modulation mode.
INT excInputAlpha	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.13	INTEGER	read-only	An alpha greater than zero enables the hierarchical coding mode.
I32 excInputCellID	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.14	Integer32	read-only	Via Cell ID the receiver knows the current network.
INT excInputInterleaver	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.15	INTEGER	read-only	Enables the bit interleaver for hierarchical coding
INT excInputCodeRate	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.16	INTEGER	read-only	Coderate can be set separately for HP and LP channel.
I32 excInputPacketLength	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.17	Integer32	read-only	The Packet length for the channel.
I32 excInputMeasuredDatarate	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.18	Integer32	read-only	The measured datarate of the input.
I32 excInputRequiredDatarate	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.19	Integer32	read-only	The required datarate of the input.
I32 excInputMaximumDelay	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.2.1.20	Integer32	read-only	Period of time between the signal leaving the play-out center (MIP inserter) and its regular transmission at the antenna. This delay is set in the MIP inserter and serves as a basis for all the transmitters in the SFN.
ostTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3		not-accessible	The table of racks.
ostEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1		not-accessible	A row (an entry) for one rack.
IND ostIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.1	IndexAB	not-accessible	The dedicated outputstage (A/B).
IND ostRackIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.2	IndexRack	not-accessible	The rack number (1..10).
NUM ostRackInletTemperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.3	FloatingPoint	read-only	The inlet temperature.
NUM ostRackOutletTemperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.4	FloatingPoint	read-only	The outlet temperature.
NUM ostRackAuxPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.5	FloatingPoint	read-only	Control voltage of auxiliary power supply of the designated rack. The value should be between 11.1 to 13.2 V.
IND ostRackAmpIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.400	IndexAmplifier	not-accessible	Amplifier Index
NUM ostRackAmpI1A	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.401	FloatingPoint	read-only	The power amplifier module current (I_1A).
NUM ostRackAmpI2A	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.402	FloatingPoint	read-only	The power amplifier module current (I_2A).
NUM ostRackAmpI3A	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.403	FloatingPoint	read-only	The power amplifier module current (I_3A).
NUM ostRackAmpI4A	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.404	FloatingPoint	read-only	The power amplifier module current (I_4A).
NUM ostRackAmpI1B	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.405	FloatingPoint	read-only	The power amplifier module current (I_1B).
NUM ostRackAmpI2B	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.406	FloatingPoint	read-only	The power amplifier module current (I_2B).
NUM ostRackAmpI3B	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.407	FloatingPoint	read-only	The power amplifier module current (I_3B).
NUM ostRackAmpI4B	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.408	FloatingPoint	read-only	The power amplifier module current (I_4B).
NUM ostRackAmpIDrv	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.409	FloatingPoint	read-only	The driver module current (I_DRV).
NUM ostRackAmpUDc	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.410	FloatingPoint	read-only	The power amplifier supply voltage.
NUM ostRackAmpIDc	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.411	FloatingPoint	read-only	The power amplifier supply current.
NUM ostRackAmpUDcControl	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.412	FloatingPoint	read-only	The power supply control voltage.
NUM ostRackAmpUReg	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.413	FloatingPoint	read-only	The power amplifier AGC voltage.
NUM ostRackAmpPowerA	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.414	FloatingPoint	read-only	The voltage power detector A.
NUM ostRackAmpPowerB	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.415	FloatingPoint	read-only	The voltage power detector B.
NUM ostRackAmpPowerOut	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.416	FloatingPoint	read-only	The voltage forward power detector.
NUM ostRackAmpPowerReflection	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.417	FloatingPoint	read-only	The voltage reflected power detector.
NUM ostRackAmpPowerReference	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.418	FloatingPoint	read-only	The reference voltage for output power.
NUM ostRackAmpDeltaPhase	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.419	FloatingPoint	read-only	The measured phase delta for output power.
NUM ostRackAmpCmdDeltaPhase	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.3.1.420	FloatingPoint	read-write	The phase delta setting for output power. The range is -50.0% to 50.0%.
exciterStatusTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20		not-accessible	Exciter status values.
exciterStatusEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1		not-accessible	A row (an entry) for one exciter.
IND excStatusExcIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.3	IndexAB	not-accessible	The dedicated exciter (A/B).
NUM excStatusRfOutputAgcRegulation	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.4	FloatingPoint	read-only	Shows the operating point of the RF regulator. The shown value should be around 50 per cent.
INT excStatusRfIqAdjustAuto	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.5	INTEGER	read-only	Automatic I/Q-Adjust.
NUM excStatusRfIqAdjustLO1Frequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.6	FloatingPoint	read-only	Modulator LO1.
I32 excStatusNominalPower	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.7	Integer32	read-write	Description.
NUM excStatusVSWR	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.9	FloatingPoint	read-only	Voltage Standing Wave Ratio
NUM excStatusSfnDelayProcessing	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.13	FloatingPoint	read-only	The Minimum signal transmit time through the exciter. This delay depends on the DVB transmission parameters.
NUM excStatusSfnDelayDynamic	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.14	FloatingPoint	read-only	The period of time by which signal processing is artificially delayed so that the desired time of transmission is obtained.
NUM excStatusSfnDelayNetwork	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.15	FloatingPoint	read-only	The signal propagation time between the play-out center (MIP inserter) and the exciter input. This delay depends on the transmission path used.
NUM excStatusSfnDelayTxOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.16	FloatingPoint	read-only	An individual transmitter specific delay. It can be adjusted via data carousel of the SFN adapter. It is true for a specific transmitter address.
NUM excStatusSfnDelayMaximum	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.17	FloatingPoint	read-only	The period of time between the signal leaving the play-out center (MIP inserter) and its regular transmission at the antenna. This delay is set in the MIP inserter and serves as a basis for all the transmitters in the SFN.
NUM excStatusSfnDelayTotal	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.18	FloatingPoint	read-only	The actual signal transit time through the exciter. This is derived from the sum of static-, dynamic-, offset- and processing delay.
INT excStatusAmplifierControl	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.20	INTEGER	read-only	Amplifier control status
I32 excStatusReqDataRateHP	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.30	Integer32	read-only	Required data rate on HP input with respect to the current TPS settings.
I32 excStatusReqDataRateLP	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.31	Integer32	read-only	Required data rate on LP input with respect to the current TPS settings.
FAI excStatusFailDelay	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.20.1.40	FailDelayStatus	read-only	Shows whether the fail delay time is qualified.
exciterPrecorrectionTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21		not-accessible	Exciter status values.
exciterPrecorrectionEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1		not-accessible	A row (an entry) for one exciter.
IND excPrecExcIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.3	IndexAB	not-accessible	The dedicated exciter (A/B).
SWI excPrecLinCorrection	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.4	SwitchOnOff	read-write	Switches on/turns off the linear precorrector.
INT excPrecLinAutomaticADE	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.5	INTEGER	read-write	Enables /disables the automatic precorrector. To get the ADE in work linear precorrection has to be switched on.
NUM excPrecLinMaxAmplitudeRipple	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.6	FloatingPoint	read-write	Sets te maximum ripple for automatic amplitude correction (0.0 ... 2.0).
I32 excPrecLinMaxGroupDelayRipple	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.7	Integer32	read-write	Sets the maximum ripple for automatic group delay correction.
NUM excPrecLinAmplitudeRipple	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.8	FloatingPoint	read-only	Shows the current amplitude ripple.
I32 excPrecLinGroupDelayRipple	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.9	Integer32	read-only	Shows the current group delay ripple.
INT excPrecLinInputLevel	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.10	INTEGER	read-only	Shows the state of the feedback signal from the measurement point between output stage and antenna.
INT excPrecLinAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.11	INTEGER	read-only	Shows if the automatic precorrector works properly.
SWI excPrecNonlinCorrection	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.12	SwitchOnOff	read-write	Switches on/turns off the nonlinear precorrector.
INT excPrecNonlinAutomaticADE	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.13	INTEGER	read-write	Enables /disables the automatic precorrector. To get the ADE in work nonlinear precorrection has to be switched on.
NUM excPrecNonlinThresholdShoulders	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.14	FloatingPoint	read-write	The target shoulder distance for ADE (0.0 ... 40.0).
NUM excPrecNonlinShoulderLeft	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.15	FloatingPoint	read-only	Displays the current measurement for the left handed shoulder distance.
NUM excPrecNonlinShoulderRight	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.16	FloatingPoint	read-only	Displays the current measurement of the right handed shoulder.
INT excPrecNonlinInputLevel	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.17	INTEGER	read-only	Shows the state of the feedback signal from the measurement point between output stage and antenna.
INT excPrecNonlinAutomatic	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.18	INTEGER	read-only	Shows if the automatic precorrector works properly.
EQU excPrecUserState	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.100	EqualizerCalibrationState	read-only	status of the user precorrection settings
EQU excPrecFactoryState	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.101	EqualizerCalibrationState	read-only	status of the factory precorrection settings
INT excPrecRestoreCurrentSettings	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.102	INTEGER	read-write	restores current factory precorrection setting
INT excPrecRestoreAllSettings	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.21.1.103	INTEGER	read-write	restores all factory precorrection settings
configurationTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30		not-accessible	Table for Type Configuration parameters.
configurationEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1		not-accessible	An entry for the Type Configuration parameters.
TVS configTvStandardIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.3	TvStandard	not-accessible	The index for the TV standard.
TVS configTvStandardName	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.5	TvStandard	read-only	The name of the TV standard as a text.
I32 configRxFrequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.6	Integer32	read-write	The input frequency for input 1.
I32 configFrequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.7	Integer32	read-write	The output frequency for input 1.
NUM configPower	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.8	FloatingPoint	read-write	The output power (0.0 ... 2500.0) for input 1.
INP configInputSource	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.30.1.9	InputSource	read-write	The source for input 1.
timeSchedulerTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31		not-accessible	Table for Time Scheduler parameters.
timeSchedulerEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1		not-accessible	An entry in the table for the Time Scheduler parameters. A row in this table is created by setting the value of schedulerRowStatus to 'createAndGo' or 'createAndWait'. A row in this table is deleted by setting the value of schedulerRowStatus to 'destroy'.
DAT schedulerDateTimeIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1.3	DateAndTime	not-accessible	The DateAndTime index. Note: Deci-seconds different from 0 and UTC values are ignored. The index is implemented as a Fixed length string of 8 components. The last component (Deci-seconds) is always 0. Example: The DateTime of 2008-9-15,17:45:30.0 has the index: 7.216.9.15.17.45.30.0
ROW schedulerRowStatus	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1.5	RowStatus	read-create	This object is used to create and delete rows in the timeSchedulerTable.
INT schedulerEvent	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1.6	INTEGER	read-create	The event type.
DAT schedulerDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1.7	DateAndTime	read-only	The start date and the time of a daily or one-time event.
TVS schedulerTvStandard	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.31.1.8	TvStandard	read-create	The TV standard.
configuration2Table	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32		not-accessible	Table for Type Configuration parameters of input 2.
configuration2Entry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1		not-accessible	An entry for the Type Configuration parameters of input 2.
TVS config2TvStandardName	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1.5	TvStandard	read-only	The name of the TV standard as a text.
I32 config2RxFrequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1.6	Integer32	read-write	The input frequency for input 2.
I32 config2Frequency	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1.7	Integer32	read-write	The output frequency for input 2.
NUM config2Power	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1.8	FloatingPoint	read-write	The output power (0.0 ... 2500.0) for input 2.
INP config2InputSource	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.32.1.9	InputSource	read-write	The source for input 2.
productInfoTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100		not-accessible	The table for product typeplates.
productInfoEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1		not-accessible	A row (an entry) for one typeplate.
PRO prodInfoModuleIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.1	ProdInfoModuleNameTv	not-accessible	The module index.
IND prodInfoDeviceIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.2	IndexAB	not-accessible	The dedicated device (A/B).
IND prodInfoRackIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.3	IndexRack	not-accessible	The rack number (1..10).
IND prodInfoAmpIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.4	IndexAmplifier	not-accessible	Amplifier Index
PRO prodInfoModuleName	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.5	ProdInfoModuleNameTv	read-only	The name of the module as a text.
STR prodInfoSerialNumber	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.6	ReadableString	read-only	The serial number of the subdevice.
STR prodInfoIdentNumberSW	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.7	ReadableString	read-only	The Rohde&Schwarz identification number of the software, for example 2094.2090.02.
STR prodInfoVersionNumberSW	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.8	ReadableString	read-only	The Rohde&Schwarz revision number of the software, for example 1.2.1.
STR prodInfoIdentNumberHW	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.9	ReadableString	read-only	The Rohde&Schwarz identification number of the hardware, for example 2095.8007.02 (NetCCU).
STR prodInfoVersionNumberHW	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.10	ReadableString	read-only	The Rohde&Schwarz revision number (product index) of the hardware, for example 03.03.
DAT productInfoProductDateHW	1.3.6.1.4.1.2566.127.1.2.167.4.1.3.100.1.11	DateAndTime	read-only	The Rohde&Schwarz production date of the hardware,
logbook	1.3.6.1.4.1.2566.127.1.2.167.4.1.4
LOG netCCUNumberOfEntries	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.1	LogbookMaxEntryNumber	read-only	The number of entries in logbook.
TRI netCCULogbookClear	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.2	Trigger	read-write	Clear the logbook. idle(1) --> ready clear(2) --> do clear now A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
netCCULogbookTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3		not-accessible	NetCCU logbook table.
netCCULogbookEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1		not-accessible	This is a entry in the logbook.
LOG netCCULogbookEntryIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.1	LogbookMaxEntryNumber	not-accessible	This is an increasing number from 1 to maximum. It is used as an index column for SNMP.
LOG netCCULogbookEntryNbr	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.2	LogbookMaxEntryNumber	read-only	This is the number of the logbook entry. It is an decreasing number from maximum down to 1.
EVE netCCULogbookType	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.3	EventClass	read-only	Can either be Fault, Warning or State.
LOG netCCULogbookSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.4	LogbookEntrySlope	read-only	Either set (event raises) or reset (event disappears)
LOG netCCULogbookMessage	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.5	LogbookEntryMessagesNetCCU	read-only	See RS-XX8000-COMMON-MIB - TextualConvention - LogbookEntryMessagesNetCCU for details.
DAT netCCULogbookDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.3.1.6	DateAndTime	read-only	netCCULogbookDateTime
LOG exciterANumberOfEntries	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.4	LogbookMaxEntryNumber	read-only	The number of entries in logbook.
TRI exciterALogbookClear	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.5	Trigger	read-write	Clear the logbook. idle(1) --> ready clear(2) --> do clear now A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
exciterALogbookTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6		not-accessible	ExciterA logbook table.
exciterALogbookEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1		not-accessible	This is a entry in the logbook.
LOG excALogbookEntryIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.1	LogbookMaxEntryNumber	not-accessible	This is an increasing number from 1 to maximum. It is used as an index column for SNMP.
LOG excALogbookEntryNbr	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.2	LogbookMaxEntryNumber	read-only	This is the number of the logbook entry. It is an decreasing number from maximum down to 1.
EVE excALogbookType	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.3	EventClass	read-only	Can either be Fault, Warning or State.
LOG excALogbookSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.4	LogbookEntrySlope	read-only	Either set (event raises) or reset (event disappears)
LOG excALogbookMessage	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.5	LogbookEntryMessagesExcTv	read-only	See RS-XX8000-COMMON-MIB - TextualConvention for details.
DAT excALogbookDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.6.1.6	DateAndTime	read-only	The time of the logbook entry.
LOG outputstageANumberOfEntries	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.7	LogbookMaxEntryNumber	read-only	The number of entries in logbook.
TRI outputstageALogbookClear	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.8	Trigger	read-write	Clear the logbook. idle(1) --> ready clear(2) --> do clear now A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
outputstageALogbookTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9		not-accessible	OutputstageA logbook table.
outputstageALogbookEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1		not-accessible	This is a entry in the logbook.
LOG ostALogbookEntryIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.1	LogbookMaxEntryNumber	not-accessible	This is an increasing number from 1 to maximum. It is used as an index column for SNMP.
LOG ostALogbookEntryNbr	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.2	LogbookMaxEntryNumber	read-only	This is the number of the logbook entry. It is an decreasing number from maximum down to 1.
EVE ostALogbookType	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.3	EventClass	read-only	Can either be Fault, Warning or State.
LOG ostALogbookSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.4	LogbookEntrySlope	read-only	Either set (event raises) or reset (event disappears)
LOG ostALogbookMessage	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.5	LogbookEntryMessagesOST	read-only	See RS-XX8000-COMMON-MIB - TextualConvention for details.
DAT ostALogbookDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.9.1.6	DateAndTime	read-only	The time of the logbook entry.
LOG exciterBNumberOfEntries	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.10	LogbookMaxEntryNumber	read-only	The number of entries in logbook.
TRI exciterBLogbookClear	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.11	Trigger	read-write	Clear the logbook. idle(1) --> ready clear(2) --> do clear now A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
exciterBLogbookTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12		not-accessible	ExciterB logbook table.
exciterBLogbookEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1		not-accessible	This is a entry in the logbook.
LOG excBLogbookEntryIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.1	LogbookMaxEntryNumber	not-accessible	This is an increasing number from 1 to maximum. It is used as an index column for SNMP.
LOG excBLogbookEntryNbr	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.2	LogbookMaxEntryNumber	read-only	This is the number of the logbook entry. It is an decreasing number from maximum down to 1.
EVE excBLogbookType	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.3	EventClass	read-only	Can either be Fault, Warning or State.
LOG excBLogbookSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.4	LogbookEntrySlope	read-only	Either set (event raises) or reset (event disappears)
LOG excBLogbookMessage	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.5	LogbookEntryMessagesExcTv	read-only	See RS-XX8000-COMMON-MIB - TextualConvention for details.
DAT excBLogbookDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.12.1.6	DateAndTime	read-only	The time of the logbook entry.
LOG outputstageBNumberOfEntries	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.13	LogbookMaxEntryNumber	read-only	The number of entries in logbook.
TRI outputstageBLogbookClear	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.14	Trigger	read-write	Clear the logbook. idle(1) --> ready clear(2) --> do clear now A GET will always return idle(1). A SET idle(1) will return NO_ERROR without doing anything.
outputstageBLogbookTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15		not-accessible	OutputstageB logbook table.
outputstageBLogbookEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1		not-accessible	This is a entry in the logbook.
LOG ostBLogbookEntryIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.1	LogbookMaxEntryNumber	not-accessible	This is an increasing number from 1 to 128. It is used as an index column for SNMP.
LOG ostBLogbookEntryNbr	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.2	LogbookMaxEntryNumber	read-only	This is the number of the logbook entry. It is an decreasing number from max 128 down to 1.
EVE ostBLogbookType	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.3	EventClass	read-only	Can either be Fault, Warning or State.
LOG ostBLogbookSlope	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.4	LogbookEntrySlope	read-only	Either set (event raises) or reset (event disappears)
LOG ostBLogbookMessage	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.5	LogbookEntryMessagesOST	read-only	See RS-XX8000-COMMON-MIB - TextualConvention for details.
DAT ostBLogbookDateTime	1.3.6.1.4.1.2566.127.1.2.167.4.1.4.15.1.6	DateAndTime	read-only	The time of the logbook entry.
rfProbesTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.5		not-accessible	This table contains all commands for the RF probes.
rfProbesEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1		not-accessible	An entry for a designated transmitter and device.
NUM rfProbesNetCCURfProbe1	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.1	FloatingPoint	read-only	Current voltage on RF Probe 1.
NUM rfProbesNetCCURfProbe2	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.2	FloatingPoint	read-only	Current voltage on RF Probe 2.
NUM rfProbesAntFwdNominal	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.3	FloatingPoint	read-write	This sets the nominal value [W] of the transmitter (to antenna).
NUM rfProbesAntFwdWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.4	FloatingPoint	read-write	This sets the warning limit for the transmitters RF control (to antenna).
NUM rfProbesAntFwdFailLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.5	FloatingPoint	read-write	This sets the fault limit for the transmitters RF control (to antenna).
I32 rfProbesAntFwdDelayTimeRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.6	Integer32	read-write	This sets the delay time for the RF Fail control (to antenna).
TRI rfProbesAntFwdSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.7	Trigger	read-write	This triggers Set Offset.
TRI rfProbesAntFwdSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.8	Trigger	read-write	This triggers Set Gain.
NUM rfProbesAntReflWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.9	FloatingPoint	read-write	This sets the warning limit for the transmitters reflection control (to antenna).
TRI rfProbesAntReflSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.10	Trigger	read-write	This triggers Set Offset.
TRI rfProbesAntReflSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.11	Trigger	read-write	This triggers Set Gain.
NUM rfProbesDLFwdNominal	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.12	FloatingPoint	read-write	This sets the nominal value [W] of the transmitter (to dummyload).
NUM rfProbesDLFwdWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.13	FloatingPoint	read-write	This sets the warning limit for the transmitters RF control (to dummyload).
NUM rfProbesDLFwdFailLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.14	FloatingPoint	read-write	This sets the fault limit for the transmitters RF control (to dummyload).
I32 rfProbesDLFwdDelayTimeRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.15	Integer32	read-write	This sets the delay time for the RF Fail control (to dummyload).
TRI rfProbesDLFwdSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.16	Trigger	read-write	This triggers Set Offset.
TRI rfProbesDLFwdSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.17	Trigger	read-write	This triggers Set Gain.
NUM rfProbesDLReflWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.18	FloatingPoint	read-write	This sets the warning limit for the transmitters reflection control (to dummyload).
TRI rfProbesDLReflSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.19	Trigger	read-write	This triggers Set Offset.
TRI rfProbesDLReflSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.20	Trigger	read-write	This triggers Set Gain.
IND rfProbesOstIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.21	IndexAB	not-accessible	The dedicated outputstage (A/B).
NUM rfProbesOstFwdNominal	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.22	FloatingPoint	read-write	This sets the nominal value [W] of the outputstage.
NUM rfProbesOstFwdWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.23	FloatingPoint	read-write	This sets the warning limit for the outputstage RF control.
NUM rfProbesOstFwdFailLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.24	FloatingPoint	read-write	This sets the fault limit for the outputstage RF control.
I32 rfProbesOstFwdDelayTimeRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.25	Integer32	read-write	This sets the delay time for the outputstage RF Fail control.
TRI rfProbesOstFwdSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.26	Trigger	read-write	This triggers Set Offset.
TRI rfProbesOstFwdSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.27	Trigger	read-write	This triggers Set Gain.
NUM rfProbesOstReflWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.28	FloatingPoint	read-write	This sets the warning limit for the outputstage reflection control.
TRI rfProbesOstReflSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.29	Trigger	read-write	This triggers Set Offset.
TRI rfProbesOstReflSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.5.1.30	Trigger	read-write	This triggers Set Gain.
rackTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.6		not-accessible	This table contains important commands for the racks.
rackEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1		not-accessible	An entry for a designated rack or rack's rf probe.
IND ostDeviceIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.2	IndexAB	not-accessible	The index to address outputstageA and outputstageB.
IND rackIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.3	IndexRack	not-accessible	The index to address the racks.
INT rackRfProbeIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.4	INTEGER	not-accessible	The index to address forward and reflected RF probes. For not RF probe parameters this index is always 1.
I32 amplifiersPerRack	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.6	Integer32	read-only	The number of amplifiers of a rack.
T/F rackRfEventSignalling	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.7	TruthValue	read-write	This configures whether to signal rf events or not.
NUM rackReferenceVoltage	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.8	FloatingPoint	read-write	This parameter controls the reference voltage (31.0 ... 100.0).
NUM amplifiersPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.9	FloatingPoint	read-write	This parameter controls the power supplies of the amplifier within the rack (31.0 ... 100.0).
INT rackGeneralPurposeInput	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.10	INTEGER	read-write	Setting of the general purpose input behaviour.
SWI rackOnOff	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.20	SwitchOnOff	read-write	This switches the rack on/off.
T/F rfProbePresent	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.50	TruthValue	read-only	If the RF probe of this rack is present.
STR rfProbeConfigurationLabel	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.51	ReadableString	read-write	Name for the measured signal on RF Probe.
I32 rfProbeConfigurationNominalValue	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.52	Integer32	read-write	The nominal value of the measured signal.
NUM rfProbeThresholdRfFailLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.55	FloatingPoint	read-write	Fault limit for the RF control (-20.0 ... 0.0).
I32 rfProbeThresholdTimeoutRfFailCtr	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.56	Integer32	read-write	Timeout for RF Fail Control.
NUM rfProbeThresholdWarningLimit	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.57	FloatingPoint	read-write	Warning limit for the RF control (-20.0 ... 0.0). For reflected probes: Warning limit for the reflection control. This limit is added to the fault limit to generate the real warning limit; e.g. the fault limit is -17.0dB and the warning limit is -3.0dB, so the warning is active on a reflected power higher than -20.0 dB.
NUM rfProbeCalibrationGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.60	FloatingPoint	read-only	Measured value of gain calibration.
NUM rfProbeCalibrationOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.61	FloatingPoint	read-only	Measured value of offset calibration.
TRI rfProbeCalibrationSetGain	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.62	Trigger	read-write	Sets the gain calibration.
TRI rfProbeCalibrationSetOffset	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.63	Trigger	read-write	Sets the offset calibration.
NUM rfProbeMeasuredValue	1.3.6.1.4.1.2566.127.1.2.167.4.1.6.1.65	FloatingPoint	read-only	Measured forward/reflected power of antenna signal.
sx801AmplifierTable	1.3.6.1.4.1.2566.127.1.2.167.4.1.7		not-accessible	Amplifier status values for SX801 amplifiers.
sx801AmplifierEntry	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1		not-accessible	A row (an entry) for one amplifier.
IND sx801AmpIdx	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.1	IndexAmplifier	not-accessible	The amplifier index.
SX8 sx801AmpRfOut	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.2	Sx801AmplifierState	read-only	Shows if the amplifier generates an RF or not. off(1): The amplifier output is switched off e.g. because the amplifier gets no input signal or the transmitter has been switched off warning(2): There is an RF but its level is less than the RF warning limit. ok(3): The RF level is greater than the RF warning limit.
SX8 sx801AmpRfIn	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.3	Sx801AmplifierState	read-only	Displays the state of the amplifier input. off(1): no input signal detected warning(2): the level of the input signal is too low or too high. ok(3): input signal is OK.
INT sx801AmpReflection	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.4	INTEGER	read-only	A reflection on RF output of this Amplifier module has been detected. This leads to a reduction of output power of the amplifier.
INT sx801AmpOn	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.5	INTEGER	read-only	Shows if the amplifier has been switched on by the control unit.
SX8 sx801AmpAC	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.6	Sx801AmplifierState	read-only	Shows the state of primary voltage of the power supply.
INT sx801AmpCommunication	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.7	INTEGER	read-only	Displays if the CAN communication between amplifier and Sx801 is working or not.
SX8 sx801AmpTransistor	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.8	Sx801AmplifierState	read-only	A transistor fail is displayed here. For further information please see the amplifiers service menue.
SX8 sx801AmpDriver	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.9	Sx801AmplifierState	read-only	Shows a failure if one of the internal driver transistors does not work properly. For further information please see the amplifiers service menue.
SX8 sx801AmpTemperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.10	Sx801AmplifierState	read-only	Shows a fault if the temperature of amplifier module is too high.
SX8 sx801AmpBlower	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.11	Sx801AmplifierState	read-only	Displays the state of the internal blowers.
SX8 sx801AmpRegulation	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.12	Sx801AmplifierState	read-only	Shows a fault if the amplifier is not able to control its output power.
T/F sx801AmpUpdate	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.13	TruthValue	read-only	Firmware update is in progress. This will be started automatically during a software update procedure of the transmitter.
SX8 sx801Supply1Temperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.14	Sx801AmplifierState	read-only	Shows a fault if the temperature of power supply one is too high.
SX8 sx801Supply2Temperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.15	Sx801AmplifierState	read-only	Shows a fault if the temperature of power supply two is too high.
SX8 sx801SupplyRTemperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.16	Sx801AmplifierState	read-only	Shows a fault if the temperature of the reserve power supply is too high.
SX8 sx801Supply1DC	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.17	Sx801AmplifierState	read-only	Shows a fault if the output voltage of power supply one is not ok.
SX8 sx801Supply2DC	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.18	Sx801AmplifierState	read-only	Shows a fault if the output voltage of power supply two is not ok.
SX8 sx801SupplyRDC	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.19	Sx801AmplifierState	read-only	Shows a fault if the output voltage of the reserve power supply is not ok.
NUM sx801AmpValueI1	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.50	FloatingPoint	read-only	The internal current from transistor pair 1.
NUM sx801AmpValueI2	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.51	FloatingPoint	read-only	The internal current from transistor pair 2.
NUM sx801AmpValueI3	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.52	FloatingPoint	read-only	The internal current from transistor pair 3.
NUM sx801AmpValueI4	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.53	FloatingPoint	read-only	The internal current from transistor pair 4.
NUM sx801AmpValueIPre	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.54	FloatingPoint	read-only	The internal current from preamplifier.
NUM sx801AmpValueIDrv1	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.55	FloatingPoint	read-only	The internal current from driver transistor pair 1.
NUM sx801AmpValueIDrv2	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.56	FloatingPoint	read-only	The internal current from driver transistor pair 2.
NUM sx801AmpValuePowerOut	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.57	FloatingPoint	read-only	The base value in Volt to calculate the output power of this amplifier module.
NUM sx801AmpValueReflection	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.58	FloatingPoint	read-only	The base value in Volt for detection of reflections.
NUM sx801AmpValueVRef	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.59	FloatingPoint	read-only	The internal reference voltage to set the output power.
NUM sx801AmpValueVReg	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.60	FloatingPoint	read-only	The internal value for output power regulation.
NUM sx801AmpValueTemperature	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.61	FloatingPoint	read-only	The internal temperature of Amplifier. In case of L-band amplifier, the shown temperature is valid only, if the amplifier is switched on.
NUM sx801AmpValueMonAtt	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.62	FloatingPoint	read-only	The attenuation of monitoring output on the front of the amplifier module (Amp RF Mon).
NUM sx801AmpValueVAux1	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.63	FloatingPoint	read-only	The voltage power detector 1.
NUM sx801AmpValueVAux2	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.64	FloatingPoint	read-only	The voltage power detector 2.
NUM sx801Supply1ValuePwr	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.65	FloatingPoint	read-only	The power supply one control voltage.
NUM sx801Supply2ValuePwr	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.66	FloatingPoint	read-only	The power supply two control voltage.
NUM sx801Supply1ValueDc	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.67	FloatingPoint	read-only	The internal supply voltage of transistor path two. In systems with two power supplies this value is equal to the output voltage of supply one.
NUM sx801Supply2ValueDc	1.3.6.1.4.1.2566.127.1.2.167.4.1.7.1.68	FloatingPoint	read-only	The internal supply voltage of transistor path two. In systems with two power supplies this value is equal to the output voltage of supply two.
rsXx8000DvbTxEvents	1.3.6.1.4.1.2566.127.1.2.167.4.3
eventTx	1.3.6.1.4.1.2566.127.1.2.167.4.3.2
eventsTxV2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0			Compatibility to SMIv1.
NTF txSummaryFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.1			Transmitter Summary Fault
NTF txSummaryWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.2			Transmitter Summary Warning
NTF txLocal	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.3			Transmitter Local/Remote
NTF txRfOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.4			Transmitter RF On/Off
NTF txRfOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.5			Transmitter RF Ok / Not OK
NTF txParamSetSubDeviceDiffers	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.6			Parameterset of subdevice is different. The currently loaded parameterset is inconsistent because a subdevice (e.g. an exciter) has a different configuration than expected. To correct this, save settings to the current or save a complete new.
NTF txParamSetValuesChanged	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.7			Value Of Current Parameterset Changed. The currently loaded parameterset is inconsistent because there were changes happening since the load/save of it. To correct this, save settings to the current or save a complete new.
NTF txRfLoopProgram	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.8			NetCCU Loop Program
NTF txRfLoopReserve	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.9			NetCCU Loop Reserve
NTF txRfWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.10			NetCCU RF Warning
NTF txReflectionWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.11			NetCCU Reflection Warning
NTF txNetCCUFanFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.12			NetCCU Fan Fault. This is valid, if Fan Control is switched on (see menu NetCCU Setup - Common).
NTF txNetCCUPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.13			NetCCU Power Supply
NTF txRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.14			NetCCU RF Fail
NTF txReflectionFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.15			NetCCU Reflection Fault
NTF txNetCCUBoardTemperatureFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.16			NetCCU Board Temperature Fault deprecated: this information is now handled as a warning (txNetCCUBoardTemperatureWarning)
NTF txNetCCUNoConnectionToExcA	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.17			NetCCU Connection To ExciterA Faulty
NTF txNetCCUNoConnectionToOstA	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.18			NetCCU Connection To OutputstageA Faulty
NTF txNetCCUNoConnectionToExcB	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.19			NetCCU Connection To ExciterB Faulty
NTF txNetCCUNoConnectionToOstB	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.20			NetCCU Connection To OutputstageB Faulty
NTF txAutomaticExcReady	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.21			Exciter Automatic Ready.
NTF txAutomaticExcChanged	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.22			Exciter Automatic Changed.
NTF txAutomaticExcFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.23			Exciter Automatic Fault.
NTF txAutomaticOstReady	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.24			Outputstage Automatic Ready. This paramter is only available for systems with an automatic output switch.
NTF txAutomaticOstChanged	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.25			Outputstage Automatic Changed. This paramter is only available for systems with an automatic output switch.
NTF txAutomaticOstFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.26			Outputstage Automatic Fault. This paramter is only available for systems with an automatic output switch.
NTF txNetCCUBoardTemperatureWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.27			NetCCU Board Temperature Warning
NTF txInternalPowerSupplyWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.30			NetCCU internal Power Supply warning
NTF txExternalPowerSupplyWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.31			NetCCU external (additional) Power Supply warning
NTF txModeSwitchOverStarted	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.35			Switch over of TX mode started.
NTF txModeSwitchOverEnded	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.36			Switch over of TX mode ended.
NTF txModeInconsistent	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.37			An inconsistency in configuration of TX mode was detected. The CCU and exiter configurations are incompatible.
NTF txModeSwitchOverFailed	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.38			Switch over of TX mode failed. Please check whether the configurations of CCU and exciter are correct.
NTF txExcSummaryFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.100			Exciter Summary Fault
NTF txExcSummaryWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.101			Exciter Summary Warning
NTF txExcLocal	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.102			Exciter Local/Remote
NTF txExcRfOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.104			Exciter RF Ok
NTF txExcInputNoConnectHP1	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.105			Exciter Input HP1 has no connected input signal
NTF txExcInputNoConnectLP1	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.106			Exciter Input LP1 has no connected input signal
NTF txExcInputNoConnectHP2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.107			Exciter Input HP2 has no connected input signal
NTF txExcInputNoConnectLP2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.108			Exciter Input LP2 has no connected input signal
NTF txExcInputActiveHP1	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.109			Exciter Input HP1 is active
NTF txExcInputActiveLP1	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.110			Exciter Input LP1 is active
NTF txExcInputActiveHP2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.111			Exciter Input HP2 is active
NTF txExcInputActiveLP2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.112			Exciter Input LP2 is active
NTF txExcOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.113			Exciter On
NTF txExcRfOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.114			Exciter RF On
NTF txExcNoInput	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.115			Exciter has no valid input signal.
NTF txExcRfLoop	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.116			Exciter RF loop
NTF txExcRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.117			Exciter RF Fail
NTF txExcSelfTest	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.118			Exciter hardware self test
NTF txExcOutputOpen	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.119			Exciter output open
NTF txExcBoardTemperatureWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.120			Exciter Board Temperature
NTF txExcFanWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.121			Exciter has one faulty fan
NTF txExcFanFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.122			Both exciter fans are faulty.
NTF txExcFifoWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.123			Exciter Fifo
NTF txExcTestSignal	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.124			Exciter Testsignal Active
NTF txExcSFNDelay	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.125			Exciter SFN Delay Fault
NTF txExcWrongDatarate	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.126			Exciter Wrong Datarate
NTF txExcMute	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.127			Exciter Mute
NTF txExcPPSFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.128			Exciter PPS Fail
NTF txExcReferenceFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.129			Exciter Reference Fail
NTF txExcMIPFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.130			Exciter MIP Fail
NTF txExcInputAutomaticSwitchReady	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.131			Input automatic is ready.
NTF txExcInputAutomaticChangedOver	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.132			Input automatic changed over.
NTF txExcInputReseveMissing	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.133			Missing input, or automatic switching enabled with only one input present. Disable automatic switching or press reset fault to remove this warning. Monitoring of a second input will start automatically if two input signals have been detected. This event will be generated only if cmdExcExpectInputReserve is set to on(1).
NTF txOstSummaryFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.200			Outputstage Summary Fault
NTF txOstSummaryWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.201			Outputstage Summary Warning
NTF txOstRfOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.202			Outputstage RF On
NTF txOstRfOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.203			Outputstage RF Ok
NTF txOstNoInput	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.204			Outputstage no input signal
NTF txOstRfWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.205			Outputstage RF Warning
NTF txOstReflectionWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.206			Outputstage Reflection Warning
NTF txOstRackWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.207			Outputstage Rack Warning. At least one rack has an error pending.
NTF txOstCoolingWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.208			Outputstage Cooling Warning
NTF txOstRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.209			Outputstage RF Fail
NTF txOstReflectionFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.210			Outputstage Reflection Fault
NTF txOstACFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.211			Outputstage AC Fault
NTF txOstCoolingFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.212			Outputstage Cooling Fault
NTF txOstCommFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.213			Outputstage Communication Fault
NTF txRackSumFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.300			Summary Fault at a designated rack. This event automatically leads to txOstRackWarning.
NTF txRackSumWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.301			Summary Warning at a designated rack.
NTF txRackOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.302			The designated racks operation mode is on.
NTF txRackGpiWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.303			A warning on the general purpose input occurred. This depends on the current configuration of the GPI. (See:Rack Setup/Rack Controller)
NTF txRackFan1Fault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.304			The designated rack signals a fault of fan 1.
NTF txRackFan2Fault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.305			The designated rack signals a fault of fan 2.
NTF txRackCoolingSumWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.306			The designated rack signals a summary cooling warning.
NTF txRackAmplifierSumFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.307			The designated rack signals at least one faulty amplifier.
NTF txRackNoLink	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.308			No communication to the designated rack.
NTF txRackGpiFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.309			A fault on the general purpose input occurred. This depends on the current configuration of the GPI. (See:Rack Setup/Rack Controller)
NTF txRackTemperatureFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.310			The designated rack signals a temperature fault - temperature too high.
NTF txRackACFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.311			The designated rack signals an AC (phase) fault.
NTF txRackCoolingSumFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.312			The designated rack signals a summary cooling fault.
NTF txRackTempFaultAbs1	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.313			The designated rack signals a temperature fault of absorber 1.
NTF txRackTempFaultAbs2	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.314			The designated rack signals a temperature fault of absorber 2.
NTF txRackDCFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.315			The designated rack signals a DC fault.
NTF txRackRfOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.318			RF power is on.
NTF txRackRfOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.319			RF power is ok.
NTF txRackRfWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.320			RF power decreased the warning threshold.
NTF txRackRfFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.321			RF output power decreased the fault threshold.
NTF txRackReflectionWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.322			The reflected power increased the warning threshold
NTF txRackReflectionFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.323			The reflected power increased the fault threshold.
NTF txRackProbeNotCalibrated	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.330			At least one probe is not calibrated.
NTF txRackTemperatureWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.331			Rack temperature exceeded the warning threshold.
NTF txRackOvervoltProtectWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.335			Overvoltage protection is out of order.
NTF txAmpSumFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.400			The designated amplifier signals summary fault.
NTF txAmpSumWarning	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.401			The designated amplifier signals summary warning.
NTF txAmpPowerOn	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.402			The designated amplifiers power is on.
NTF txAmpDCOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.403			The designated amplifiers DC is ok.
NTF txAmpACOk	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.404			The designated amplifiers AC is ok.
NTF txAmpRfInFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.405			The designated amplifier signals RF input fail.
NTF txAmpRfFail	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.406			The designated amplifier signals RF fail.
NTF txAmpReflectionFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.407			The designated amplifier signals a reflection fault.
NTF txAmpTemperatureFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.408			The designated amplifier signals a temperature fault - temperature is too high.
NTF txAmpTransistorFault	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.0.409			The designated amplifier signals at least one faulty transistor.
eventsTxTable	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1		not-accessible	This table contains necessary information for handling alarms. For each alarm you have the following information: - name (get), - mask to enable/disable sending out (set/get), - priority (set/get) and - the current state (get only).
eventsTxEntry	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1		not-accessible	An event entry always consists of its indexes (used for addressing within redundancy systems) and 3 values: - name: an enumerated list of all possible notifications - mask: the corresponding mask (enable/disable) - priority: the corresponding priority (value in range 0..255) - event: the event itself (active/inactive)
INT eventTxABIdx	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.1	INTEGER	not-accessible	The value for the module A (exciterA, outputstageA) or B (exciterB, outputstageB) for alarms. This is a helper column and therefore not-accessible.
I32 eventTxRackIdx	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.2	Integer32	not-accessible	The number of the designated rack. This is a helper column and therefore not-accessible.
I32 eventTxAmpIdx	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.3	Integer32	not-accessible	The number of the designated amplifier. This is a helper column and therefore not-accessible.
EVE eventTxNameIdx	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.4	EventMaxEntryNumber	not-accessible	The event number as integer. This is a helper column and therefore not-accessible.
INT eventTxName	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.5	INTEGER	read-only	The event number as integer and the value as readable text. The enumeration correlates with the notifications under eventsTxV2.
EVE eventTxMask	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.6	EventMask	read-write	See TextualConvention for details.
EVE eventTxPriority	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.7	EventPriority	read-write	See TextualConvention for details.
EVE eventTxEvent	1.3.6.1.4.1.2566.127.1.2.167.4.3.2.1.1.8	EventState	read-only	See TextualConvention for details.
rsXx8000DvbTxConf	1.3.6.1.4.1.2566.127.1.2.167.4.5
rsXx8000DvbTxGroups	1.3.6.1.4.1.2566.127.1.2.167.4.5.1
groupEvents	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.1			This group includes all OIDs for event handling.
groupTxCommon	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.2			Group for common transmitter objects
groupEventsTxCommon	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.3			This group includes all alarm OIDs that are common for all reserve concepts.
groupDualDrive	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.4			This group includes additional objects for reserve concepts DualDrive (NetCCU + 2 * exciter + outputstage) and Active/Passive Reserve (NetCCU + 2 * exciter + 2 * outputstage)
groupEventsDualDrive	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.5			This group includes additional events for reserve concepts DualDrive (NetCCU + 2 * exciter + outputstage) and Active/Passive Reserve (NetCCU + 2 * exciter + 2 * outputstage)
groupPowerReserve	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.6			This group includes additional objects for reserve concept Active/Passive Reserve (NetCCU + 2 * exciter + 2 * outputstage) For more details, refer to manual.
groupEventsPowerReserve	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.7			This group includes additional events for reserve concept Active/Passive Reserve (NetCCU + 2 * exciter + 2 * outputstage) For more details, refer to manual.
groupCommonMP	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.8			additional objects for medium/high power
groupEventsCommonMP	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.9			additional events for medium/high power
groupCommonNetCCU	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.10			additional objects for transmitters with NetCCU
groupEventsCommonNetCCU	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.11			additional events for transmitters with NetCCU
groupOstBLogbook	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.12			objects of logbook for output stage B
groupSumProbe	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.14			objects that are available only when sum probe exists
groupProductInfo	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.18			This group includes all OIDs for device product information.
groupAmpMeasureValues	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.19			This group includes all OIDs amplifier measure values. Practically, these information are not important to customers, they are needed in manufactory.
groupEventsAmplifier	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.20			events from the amplifier (medium/high power only)
groupRfProbes	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.21			This group includes all OIDs regarding RF Probes.
groupDummyLoadRF	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.22			This group includes all object types regarding probes from dummy load. The object types in this group are defined only when a dummy load measure point exists. This can occur in reserve concept active reserve only.
groupExcCommon	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.23			Group for common exciter objects
groupExcAdditionalSx800	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.24			Additional exciter objects for the Sx800
groupExcAdditionalSLx	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.25			Additional exciter objects for the SLx and the Sx801
groupEventsExciter	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.26			events from the exciter
groupExciterStatus	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.27			Group for exciterStatusTable.
groupExciterPrecorrection	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.28			Group for exciterPrecorrectionTable.
groupSLx	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.29			object types that are relevant for SLx devices only
groupObjectsACU	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.30			objects from ACU
groupIndependentRacks	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.31			object types that are relevant for NX variants with independent racks only
groupObjectsRE	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.32			object types for the re-equip kit
groupEventsControlExciter	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.34			additional events in case Sx801 is control exciter
groupEventsAdditionalPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.35			Events that are available only when additionalPowerSupply is true.
groupObjsAdditionalPowerSupply	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.36			Objects that are available only when additionalPowerSupply is true.
groupObjectsControlExciter	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.37			additional objects in case Sx801 is control exciter
groupObjectsSingleEnded	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.38			Group for objects in case of SingleTx or DualDrive.
groupObjectsSx801Amplifier	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.39			Objects for Sx801/SA801 amplifier status.
groupObsoleted	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.99			obsoleted or deprecated objects
groupEventsObsoleted	1.3.6.1.4.1.2566.127.1.2.167.4.5.1.100			obsoleted or deprecated events
rsXx8000DvbTxCompl	1.3.6.1.4.1.2566.127.1.2.167.4.5.3
rsXx8000DVBSingleTxMP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.1			Reserve concept SingleTransmitter for Medium Power.
rsXx8000DVBDualDriveMP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.2			Reserve concept DualDrive for Medium Power.
rsXx8000DVBPowerReserveMP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.3			Reserve concept Active/Passive Reserve for Medium Power.
rsXx8000DVBSingleTxLP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.5			Reserve concept Low Power SingleTransmitter with NetCCU, meaning there is a NetCCU and a LowPower exciter with one or more (to the exciter) connected amplifiers.
rsXx8000DVBDualDriveLP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.6			Reserve concept DualDrive for Low Power.
rsXx8000DVBPowerReserveLP	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.7			Reserve concept Active/Passive Reserve for Low Power.
rsXx8000DVBSingleTxLPNoNetCCU	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.9			Reserve concept Low Power SingleTransmitter without NetCCU, meaning there is only a LowPower exciter with one or more (to the exciter) connected amplifiers.
rsXx8000DVBSLx	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.10			SLx device
rsXx8000DVBExciterOnly	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.11			DVB Exciter of 8000 series in a 7000 environment or Program Exciter in a Sx801 Backup Exciter environment.
rsXx8000DVBSx801ControlExciter	1.3.6.1.4.1.2566.127.1.2.167.4.5.3.12			Sx801 as control exciter
rsXx8000DvbTxMibModule	1.3.6.1.4.1.2566.149.1.163.3			This MIB defines transmitting systems from Rohde & Schwarz. Use this MIB if your system meets the following requirements: - series XX8000 (NetCCU800), - DVB, - transmitter reserve concept SingleTx, DualDrive, Active Reserve or Passive Reserve. The following MIBs are related to this: - RS-COMMON-MIB - mandatory for this MIB - RS-XX8000-COMMON-MIB - mandatory for this MIB

RFC description

Manages DVB-T transmitters with RF power, exciter control, and thermal monitoring capabilities.

Start monitoring Rohde & Schwarz XX8000/NetCCU800 series DVB transmitter systems (exciter/reserve switching control) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RS-XX8000-DVB-TX-MIB

What Is RS-XX8000-DVB-TX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description