All MIBs › OMNI-gx2dualdrr2x-MIB › dualdrr2xvalueTrippoint2Mode
dualdrr2xvalueTrippoint2Mode
Module: OMNI-gx2dualdrr2x-MIB
OID (symbolic): OMNI-gx2dualdrr2x-MIB::dualdrr2xvalueTrippoint2Mode
OID (numeric): 1.3.6.1.4.1.1166.6.1.2.35.3.2.16
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The value of this object is the current value of trip point mode. There are three possible value: 1-off, 2-alarm_only, 3-alarm&switch.
If module input optical power is higher than the preset trippoint value, no operational difference for these three modes.
If module input optical power is less than the preset trippoint value, 1) When trippoint mode is OFF, no trippoint alarm will be generated and RF output impedance will stay normal as low. 2) When tripoint mode is ALARM_ONLY, trip_point alarm will be generated when the input optical power lower than the preset trippoint level but RF output impedance will stay normal as low. 3) When trippoint mode is ALARM_SWITCH, trip point alarm will be generated and RF output impedance will switch to abnorml
What is dualdrr2xvalueTrippoint2Mode?
Selects what the module does when its input optical power drops below trip point 2: 1 off (no alarm, RF output stays at normal low impedance), 2 alarmOnly (raise the trip point alarm but leave RF output normal), 3 alarm-and-Switch (alarm and switch RF output impedance to abnormal). Above the threshold all three behave the same, so use 3 only where a redundant path should take over.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.1166.6.1.2.35.3.2.16 snmpwalk -v2c -c public <target> OMNI-gx2dualdrr2x-MIB::dualdrr2xvalueTrippoint2Mode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.1166.6.1.2.35.3.2.16.1 snmpget -v2c -c public <target> OMNI-gx2dualdrr2x-MIB::dualdrr2xvalueTrippoint2Mode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.1166.6.1.2.35.3.2.16.1 i <value>
Start monitoring General Instrument OmniStar GX2 HFC headend/optical node (gx2dualdrr2x dual optical receiver module) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the OMNI-gx2dualdrr2x-MIB::dualdrr2xvalueTrippoint2Mode OID value, configure state conditions and alerts, and monitor any General Instrument OmniStar GX2 HFC headend/optical node (gx2dualdrr2x dual optical receiver module) from a single console.
OID Breakdown
Upper-level ancestors (11 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.1166 | gi | BCS-IDENT-MIB |
| 1.3.6.1.4.1.1166.6 | motproxies | BCS-IDENT-MIB |
| 1.3.6.1.4.1.1166.6.1 | hfc | GX2HFC-MIB |
| 1.3.6.1.4.1.1166.6.1.2 | hfcDevices | GX2HFC-MIB |
| 1.3.6.1.4.1.1166.6.1.2.35 | gx2DualDrr2x | GX2HFC-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.1166.6.1.2.35.3 | gx2dualdrr2xDigitalTable | OMNI-gx2dualdrr2x-MIB |
| 1.3.6.1.4.1.1166.6.1.2.35.3.2 | gx2dualdrr2xDigitalEntry | OMNI-gx2dualdrr2x-MIB |
| 1.3.6.1.4.1.1166.6.1.2.35.3.2.16 | dualdrr2xvalueTrippoint2Mode | OMNI-gx2dualdrr2x-MIB |