Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB

All MIBs › Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB

Category: Nortel Passport WAN

Description: Manages ETSI QSIG signalling protocol configuration on Nortel MsCarrier Passport virtual network interfaces.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB?

This Nortel MIB, part of the MscPassport family for the Nortel Passport WAN switching platform, manages ETSI QSIG signalling protocol configuration on virtual network (Vnet) signalling channels, QSIG being a standardized ISDN-based signalling protocol for private telephony networks. It exposes objects for provisioning QSIG signalling channel components and their Layer 2 timer parameters, such as retransmission and window-size timers. Its monitoring role is centered on signalling software/protocol health: administrators check whether QSIG channel components and their framers are correctly provisioned and active, and whether L2 timer values (T200, T203, N200) are set appropriately, since misconfigured timers can cause link-level signalling instability. It depends on the shared MscPassport component-object conventions (row status, storage type, indexing) and conceptually on the ETSI QSIG/ISDN Q.921-based Layer 2 standard. It is deployed on carrier Nortel Passport nodes providing private ISDN/QSIG interconnect between PBXs or virtual private network switching nodes. Engineers can download the Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Passport WAN switch (ETSI QSIG virtual network signalling)

Monitoring Examples

An engineer checks mscSigChanEQsigRowStatusTable for a given mscSigChanEQsigIndex to confirm the QSIG signalling channel's row status is active, then reviews mscSigChanEQsigL2Table entries for mscSigChanEQsigT200 and mscSigChanEQsigN200 to verify Layer 2 retransmission timer and retry-count settings match the far-end PBX configuration. The associated mscSigChanEQsigFramer component status indicates whether the physical framing layer underneath the signalling channel is operational. Frequent QSIG link resets combined with mismatched T200/N200 values between the two ends is a classic cause of unstable QSIG signalling.

What Can Be Monitored

QSIG channel row status
Layer 2 timer values (T200, N200)
framer component status
signalling channel provisioning

Imported Objects

From Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB

DisplayString
RowStatus
StorageType
Unsigned32

From Nortel-MsCarrier-MscPassport-TextualConventionsMIB

Link
NonReplicated

From Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB

mscPassportMIBs

OBJECT-IDENTITY

From Nortel-MsCarrier-MscPassport-VoiceNetworkingMIB

mscSigChan	OBJECT-IDENTITY
mscSigChanIndex	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
mscSigChanEQsig	1.3.6.1.4.1.562.36.2.1.115.2
mscSigChanEQsigRowStatusTable	1.3.6.1.4.1.562.36.2.1.115.2.1		not-accessible	This entry controls the addition and deletion of mscSigChanEQsig components.
mscSigChanEQsigRowStatusEntry	1.3.6.1.4.1.562.36.2.1.115.2.1.1		not-accessible	A single entry in the table represents a single mscSigChanEQsig component.
ROW mscSigChanEQsigRowStatus	1.3.6.1.4.1.562.36.2.1.115.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscSigChanEQsig components. These components can be added and deleted.
STR mscSigChanEQsigComponentName	1.3.6.1.4.1.562.36.2.1.115.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscSigChanEQsigStorageType	1.3.6.1.4.1.562.36.2.1.115.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscSigChanEQsig tables.
NON mscSigChanEQsigIndex	1.3.6.1.4.1.562.36.2.1.115.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscSigChanEQsig tables.
mscSigChanEQsigFramer	1.3.6.1.4.1.562.36.2.1.115.2.2
mscSigChanEQsigFramerRowStatusTable	1.3.6.1.4.1.562.36.2.1.115.2.2.1		not-accessible	This entry controls the addition and deletion of mscSigChanEQsigFramer components.
mscSigChanEQsigFramerRowStatusEntry	1.3.6.1.4.1.562.36.2.1.115.2.2.1.1		not-accessible	A single entry in the table represents a single mscSigChanEQsigFramer component.
ROW mscSigChanEQsigFramerRowStatus	1.3.6.1.4.1.562.36.2.1.115.2.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscSigChanEQsigFramer components. These components cannot be added nor deleted.
STR mscSigChanEQsigFramerComponentName	1.3.6.1.4.1.562.36.2.1.115.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscSigChanEQsigFramerStorageType	1.3.6.1.4.1.562.36.2.1.115.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscSigChanEQsigFramer tables.
NON mscSigChanEQsigFramerIndex	1.3.6.1.4.1.562.36.2.1.115.2.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscSigChanEQsigFramer tables.
mscSigChanEQsigFramerProvTable	1.3.6.1.4.1.562.36.2.1.115.2.2.10		not-accessible	This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
mscSigChanEQsigFramerProvEntry	1.3.6.1.4.1.562.36.2.1.115.2.2.10.1		not-accessible	An entry in the mscSigChanEQsigFramerProvTable.
LIN mscSigChanEQsigFramerInterfaceName	1.3.6.1.4.1.562.36.2.1.115.2.2.10.1.1	Link	read-write	This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
mscSigChanEQsigFramerStateTable	1.3.6.1.4.1.562.36.2.1.115.2.2.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscSigChanEQsigFramerStateEntry	1.3.6.1.4.1.562.36.2.1.115.2.2.12.1		not-accessible	An entry in the mscSigChanEQsigFramerStateTable.
INT mscSigChanEQsigFramerAdminState	1.3.6.1.4.1.562.36.2.1.115.2.2.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscSigChanEQsigFramerOperationalState	1.3.6.1.4.1.562.36.2.1.115.2.2.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscSigChanEQsigFramerUsageState	1.3.6.1.4.1.562.36.2.1.115.2.2.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscSigChanEQsigFramerStatsTable	1.3.6.1.4.1.562.36.2.1.115.2.2.13		not-accessible	This group contains the operational statistics data for a Framer component.
mscSigChanEQsigFramerStatsEntry	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1		not-accessible	An entry in the mscSigChanEQsigFramerStatsTable.
U32 mscSigChanEQsigFramerFrmToIf	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.1	Unsigned32	read-only	This attribute counts the number of frames transmitted to the link interface by Framer. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerFrmFromIf	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.2	Unsigned32	read-only	This attribute counts the number of frames received from the link interface by Framer. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerOctetFromIf	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.3	Unsigned32	read-only	The number of bytes received from the link interface by Framer.
U32 mscSigChanEQsigFramerAborts	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.4	Unsigned32	read-only	This attribute counts the total number of aborts received. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerCrcErrors	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.5	Unsigned32	read-only	This attribute counts the total number of frames with CRC errors. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerLrcErrors	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.6	Unsigned32	read-only	This attribute counts the total number of frames with LRC errors. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerNonOctetErrors	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.7	Unsigned32	read-only	This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerOverruns	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.8	Unsigned32	read-only	This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerUnderruns	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.9	Unsigned32	read-only	This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after reaching its maximum value.
U32 mscSigChanEQsigFramerLargeFrmErrors	1.3.6.1.4.1.562.36.2.1.115.2.2.13.1.10	Unsigned32	read-only	This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after reaching its maximum value.
mscSigChanEQsigL2Table	1.3.6.1.4.1.562.36.2.1.115.2.11		not-accessible	This group specifies the provisionable layer 2 attributes of the Q.931 ITU-T protocol.
mscSigChanEQsigL2Entry	1.3.6.1.4.1.562.36.2.1.115.2.11.1		not-accessible	An entry in the mscSigChanEQsigL2Table.
U32 mscSigChanEQsigT23	1.3.6.1.4.1.562.36.2.1.115.2.11.1.1	Unsigned32	read-write	This attribute specifies the layer 2 enable request timer.
U32 mscSigChanEQsigT200	1.3.6.1.4.1.562.36.2.1.115.2.11.1.2	Unsigned32	read-write	This attribute specifies the maximum time between a layer 2 frame and its acknowledgment.
U32 mscSigChanEQsigN200	1.3.6.1.4.1.562.36.2.1.115.2.11.1.3	Unsigned32	read-write	This attribute specifies the maximum number of re-transmissions of a layer 2 frame.
U32 mscSigChanEQsigT203	1.3.6.1.4.1.562.36.2.1.115.2.11.1.4	Unsigned32	read-write	This attribute specifies the maximum time for which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.
U32 mscSigChanEQsigCircuitSwitchedK	1.3.6.1.4.1.562.36.2.1.115.2.11.1.6	Unsigned32	read-write	This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.
mscSigChanEQsigL3Table	1.3.6.1.4.1.562.36.2.1.115.2.12		not-accessible	This group represents the provisionable Layer 3 timer attributes of the ETSI Qsig protocol.
mscSigChanEQsigL3Entry	1.3.6.1.4.1.562.36.2.1.115.2.12.1		not-accessible	An entry in the mscSigChanEQsigL3Table.
U32 mscSigChanEQsigT309	1.3.6.1.4.1.562.36.2.1.115.2.12.1.3	Unsigned32	read-write	This attribute specifies the data link failure timer; used to ride out temporary failures.
U32 mscSigChanEQsigT310	1.3.6.1.4.1.562.36.2.1.115.2.12.1.4	Unsigned32	read-write	This attribute specifies the call proceeding state timer.
mscSigChanEQsigProvTable	1.3.6.1.4.1.562.36.2.1.115.2.13		not-accessible	This group defines the general options of the D-channel signalling link.
mscSigChanEQsigProvEntry	1.3.6.1.4.1.562.36.2.1.115.2.13.1		not-accessible	An entry in the mscSigChanEQsigProvTable.
INT mscSigChanEQsigSide	1.3.6.1.4.1.562.36.2.1.115.2.13.1.1	INTEGER	read-write	This attribute specifies whether the interface is the network or user side of the connection. The parameter applies to both the layer 2 and layer 3 of the interface. If this attribute is set to network, then the interface is master during channel negotiation. If this attribute is set to user, then the interface is slave during channel negotiation.
U32 mscSigChanEQsigMaxNonCallConcurrent	1.3.6.1.4.1.562.36.2.1.115.2.13.1.2	Unsigned32	read-write	This attribute specifies the maximum number of simultaneous active non-call messages that are allowed.
INT mscSigChanEQsigOverlapSendingEnabled	1.3.6.1.4.1.562.36.2.1.115.2.13.1.3	INTEGER	read-write	This attribute specifies whether overlap sending to the PBX is enabled.
INT mscSigChanEQsigOverlapReceivingEnabled	1.3.6.1.4.1.562.36.2.1.115.2.13.1.4	INTEGER	read-write	This attribute specifies whether overlap receiving from the PBX is enabled.
mscSigChanEQsigStateTable	1.3.6.1.4.1.562.36.2.1.115.2.14		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscSigChanEQsigStateEntry	1.3.6.1.4.1.562.36.2.1.115.2.14.1		not-accessible	An entry in the mscSigChanEQsigStateTable.
INT mscSigChanEQsigAdminState	1.3.6.1.4.1.562.36.2.1.115.2.14.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscSigChanEQsigOperationalState	1.3.6.1.4.1.562.36.2.1.115.2.14.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscSigChanEQsigUsageState	1.3.6.1.4.1.562.36.2.1.115.2.14.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscSigChanEQsigStatsTable	1.3.6.1.4.1.562.36.2.1.115.2.15		not-accessible	This group provides the operational components for the EtsiQsig component.
mscSigChanEQsigStatsEntry	1.3.6.1.4.1.562.36.2.1.115.2.15.1		not-accessible	An entry in the mscSigChanEQsigStatsTable.
U32 mscSigChanEQsigTotalCallsToIf	1.3.6.1.4.1.562.36.2.1.115.2.15.1.2	Unsigned32	read-only	This attribute counts the total number of calls that have been made to the interface. The value wraps when it reaches its maximum.
U32 mscSigChanEQsigTotalCallsFromIf	1.3.6.1.4.1.562.36.2.1.115.2.15.1.3	Unsigned32	read-only	This attribute counts the total number of calls from the interface. The value wraps when it reaches its maximum.
U32 mscSigChanEQsigNonCallAssocSessionsToIf	1.3.6.1.4.1.562.36.2.1.115.2.15.1.4	Unsigned32	read-only	This attribute counts the total number of non-call associated sessions to the interface. The value wraps when it reaches its maximum.
U32 mscSigChanEQsigNonCallAssocSessionsFromIf	1.3.6.1.4.1.562.36.2.1.115.2.15.1.5	Unsigned32	read-only	This attribute counts the total number of non-call associated sessions from the interface. The value wraps when it reaches its maximum.
mscSigChanEQsigOperTable	1.3.6.1.4.1.562.36.2.1.115.2.16		not-accessible	This group provides the operational attributes for the EtsiQsig protocol.
mscSigChanEQsigOperEntry	1.3.6.1.4.1.562.36.2.1.115.2.16.1		not-accessible	An entry in the mscSigChanEQsigOperTable.
U32 mscSigChanEQsigActiveChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.1	Unsigned32	read-only	This attribute indicates the number of currently active channels. This includes data and voice channels.
U32 mscSigChanEQsigActiveVoiceChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.2	Unsigned32	read-only	This attribute indicates the number of channels that are currently carrying voice.
U32 mscSigChanEQsigActiveDataChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.3	Unsigned32	read-only	This attribute indicates the number of channels that are currently carrying data. This does not include modem data.
U32 mscSigChanEQsigPeakActiveChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.4	Unsigned32	read-only	This attribute indicates the maximum number of channels that have been active on this signalling channel during the last polling period.
U32 mscSigChanEQsigPeakActiveVoiceChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.5	Unsigned32	read-only	This attribute indicates the maximum number of voice channels that have been active on this signalling channel during the last polling period.
U32 mscSigChanEQsigPeakActiveDataChannels	1.3.6.1.4.1.562.36.2.1.115.2.16.1.6	Unsigned32	read-only	This attribute indicates the maximum number of data channels that have been active on this signalling channel during the last polling period.
INT mscSigChanEQsigDChanStatus	1.3.6.1.4.1.562.36.2.1.115.2.16.1.7	INTEGER	read-only	This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is enabled. If the signalling channel stays in the established state, then it is waiting for a restart from the PBX. enabling means that the resources for processing calls are being initialized. If the signalling channel stays in the enabling state then it is waiting for a restart acknowledgement from the PBX. inService means that the resources for processing calls are available. restarting means that the resources for call processing are being rei-initialized.
mscSigChanEQsigToolsTable	1.3.6.1.4.1.562.36.2.1.115.2.17		not-accessible	This contains a series of operational attributes which turn on and off several kinds of tracing.
mscSigChanEQsigToolsEntry	1.3.6.1.4.1.562.36.2.1.115.2.17.1		not-accessible	An entry in the mscSigChanEQsigToolsTable.
OCT mscSigChanEQsigTracing	1.3.6.1.4.1.562.36.2.1.115.2.17.1.1	OCTET STRING	read-write	This attribute defines which types of tracing are active for this signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueue attribute in Col/debug must be greater than 0 and a Telnet NMIS session must list the debug stream in in its data streams (ex. set nmis telnet session/1 dataStreams debug). Different types of tracing can be enabled simultaneously. Note that tracing consumes additional CPU resources and will slow down call processing on a heavily loaded card. If there is message block exhaustion tracing will be suspended for a period and then automatically reenabled. An alarm is generated on tracing suspension and resumption. This mechanism protects the function processor against excessive numbers of tracing messages. Types of tracing include: protocolErrors - get details of any protocol errors which are occuring. Protocol errors are also reported in summary form as alarms. q931Summary - Summary of the Q.931 messages on the signalling link, including certain call details (calling number, called number, release codes). q931Hex - Q.931 messages displayed in hex format. Useful to determine protocol compliance in case of errors reported on local or remote ends. q931Symbolic - Q.931 messages parsed to give maximum detail. Useful for understanding content of messages flowing on the link. portHex - Messages in hex format being sent and received on the link. Description of bits: protocolErrors(0) q931Summary(1) q931Hex(2) q931Symbolic(3) portHex(4)
mscSigChanEQsigEQsigSpecificProvTable	1.3.6.1.4.1.562.36.2.1.115.2.18		not-accessible	This group provides EtsiQsig protocol specific provisioning.
mscSigChanEQsigEQsigSpecificProvEntry	1.3.6.1.4.1.562.36.2.1.115.2.18.1		not-accessible	An entry in the mscSigChanEQsigEQsigSpecificProvTable.
INT mscSigChanEQsigMsgSegmentation	1.3.6.1.4.1.562.36.2.1.115.2.18.1.1	INTEGER	read-write	This attribute allows users to enable/disable the EtsiQsig message segmentation service.
INT mscSigChanEQsigE1ChannelNumbers	1.3.6.1.4.1.562.36.2.1.115.2.18.1.2	INTEGER	read-write	This attribute is applicable to E1 interfaces only. It specifies the mapping scheme between channel numbers (identified in Layer 3 messages) and timeslot numbers on the E1 link. When the attribute value is skip16, channel numbers map directly to actual E1 timeslots; therefore only channel numbers 1 - 15 and 17 - 31 are expected. When the value is contiguous, channel numbers from 1 - 30 are expected, and the following mapping is used: channels 1 - 15 are mapped to timeslots 1 - 15, and channels 16 - 30 are mapped to timeslots 17 - 31. On T1 interfaces, channel numbers are always expected in the range 1 - 23.
mscSigChanEQsigEQsigSpecificOpTable	1.3.6.1.4.1.562.36.2.1.115.2.19		not-accessible	This group provides specific operational attributes for the Etsi Qsig protocol.
mscSigChanEQsigEQsigSpecificOpEntry	1.3.6.1.4.1.562.36.2.1.115.2.19.1		not-accessible	An entry in the mscSigChanEQsigEQsigSpecificOpTable.
U32 mscSigChanEQsigSegmentationAccepted	1.3.6.1.4.1.562.36.2.1.115.2.19.1.1	Unsigned32	read-only	This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and forwarded to a Passport subnet. The value wraps when it reaches its maximum.
U32 mscSigChanEQsigSegmentationFailed	1.3.6.1.4.1.562.36.2.1.115.2.19.1.2	Unsigned32	read-only	This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and could not be forwarded as is to a Passport subnet due to end-to-end incompatibility. The value wraps when it reaches its maximum.
vnetEtsiQsigMIB	1.3.6.1.4.1.562.36.2.2.110
vnetEtsiQsigGroup	1.3.6.1.4.1.562.36.2.2.110.1
vnetEtsiQsigGroupCA	1.3.6.1.4.1.562.36.2.2.110.1.1
vnetEtsiQsigGroupCA02	1.3.6.1.4.1.562.36.2.2.110.1.1.3
vnetEtsiQsigGroupCA02A	1.3.6.1.4.1.562.36.2.2.110.1.1.3.2
vnetEtsiQsigCapabilities	1.3.6.1.4.1.562.36.2.2.110.3
vnetEtsiQsigCapabilitiesCA	1.3.6.1.4.1.562.36.2.2.110.3.1
vnetEtsiQsigCapabilitiesCA02	1.3.6.1.4.1.562.36.2.2.110.3.1.3
vnetEtsiQsigCapabilitiesCA02A	1.3.6.1.4.1.562.36.2.2.110.3.1.3.2

RFC description

Nortel MIB module for managing Virtual Network configuration with ETSI QSIG signaling protocol. Defines objects for provisioning and monitoring QSIG signaling channels on Nortel Passport carrier-grade equipment.

Start monitoring Nortel Passport WAN switch (ETSI QSIG signalling channels) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB

What Is Nortel-MsCarrier-MscPassport-VnetEtsiQsigMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description