All MIBs › Nortel-Magellan-Passport-AtmBearerServiceMIB
Category: ATM
Description: Manages Nortel Magellan Passport ATM bearer service parameters for CBR, VBR, and UBR connections.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Nortel-Magellan-Passport-AtmBearerServiceMIB?
This is one of a family of Nortel Magellan Passport MIB modules, covering ATM bearer service configuration on Passport wide-area switching platforms, specifically Network Resource Partitioning (NRP) for ATM virtual path connections (VPCs) and virtual channel connections (VCCs) supporting CBR, VBR, and UBR service categories. It exposes provisioning tables (atmIfVpcNrpProvTable) and row-status/component management tables (atmIfVpcNrpRowStatusTable) that define how ATM bandwidth resources are partitioned and provisioned per interface. Its role in monitoring is configuration/provisioning verification rather than hardware fault detection: administrators confirm NRP connection point types, next-hop routing, and OAM segment boundary settings are correctly provisioned for a given ATM VPC, and check row status to ensure entries are active. Given its Magellan Passport lineage this module is part of a broader Nortel Passport MIB suite and shares common component-naming/row-status conventions (atmIfVpcNrpComponentName, atmIfVpcNrpStorageType) with sibling Passport MIBs. It was deployed on Nortel Magellan Passport ATM/frame-relay wide-area switches in carrier and enterprise WAN backbone networks, and engineers supporting these platforms can obtain a Nortel-Magellan-Passport-AtmBearerServiceMIB download to load the module into their provisioning tools.
IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-AtmBearerServiceMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nortel Magellan Passport ATM/WAN switch
Monitoring Examples
An administrator would poll atmIfVpcNrpProvTable (rows in atmIfVpcNrpProvEntry) to verify the atmIfVpcNrpNextHop and atmIfVpcNrpConnectionPointType provisioned for a given VPC, and check atmIfVpcNrpOamSegmentBoundary to confirm OAM cell handling boundaries are set correctly for fault isolation. Checking atmIfVpcNrpRowStatusTable entries for a row stuck in a non-active state would reveal a failed or incomplete provisioning operation on that ATM interface.
What Can Be Monitored
- ATM VPC/VCC NRP provisioning
- connection point type
- next-hop configuration
- OAM segment boundary settings
- row/provisioning status
This MIB depends on
Related MIBs
Imported Objects
From Nortel-Magellan-Passport-AtmCoreMIB
| atmIfIndex | OBJECT-TYPE |
| atmIfVcc | OBJECT-IDENTITY |
| atmIfVccIndex | OBJECT-TYPE |
| atmIfVpc | OBJECT-IDENTITY |
| atmIfVpcIndex | OBJECT-TYPE |
| atmIfVptIndex | OBJECT-TYPE |
| atmIfVptVcc | OBJECT-IDENTITY |
| atmIfVptVccIndex | OBJECT-TYPE |
From Nortel-Magellan-Passport-StandardTextualConventionsMIB
| DisplayString | |
| RowStatus | |
| StorageType |
From Nortel-Magellan-Passport-TextualConventionsMIB
| Link | |
| NonReplicated |
From Nortel-Magellan-Passport-UsefulDefinitionsMIB
| passportMIBs | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| atmIfVpcNrp | 1.3.6.1.4.1.562.2.4.1.114.4.4 | |||
| atmIfVpcNrpRowStatusTable | 1.3.6.1.4.1.562.2.4.1.114.4.4.1 | not-accessible | This entry controls the addition and deletion of atmIfVpcNrp components. | |
| atmIfVpcNrpRowStatusEntry | 1.3.6.1.4.1.562.2.4.1.114.4.4.1.1 | not-accessible | A single entry in the table represents a single atmIfVpcNrp component. | |
| ROW atmIfVpcNrpRowStatus | 1.3.6.1.4.1.562.2.4.1.114.4.4.1.1.1 | RowStatus | read-write | This variable is used as the basis for SNMP naming of atmIfVpcNrp components. These components can be added and deleted. |
| STR atmIfVpcNrpComponentName | 1.3.6.1.4.1.562.2.4.1.114.4.4.1.1.2 | DisplayString | read-only | This variable provides the component's string name for use with the ASCII Console Interface |
| STO atmIfVpcNrpStorageType | 1.3.6.1.4.1.562.2.4.1.114.4.4.1.1.4 | StorageType | read-only | This variable represents the storage type value for the atmIfVpcNrp tables. |
| NON atmIfVpcNrpIndex | 1.3.6.1.4.1.562.2.4.1.114.4.4.1.1.10 | NonReplicated | not-accessible | This variable represents the index for the atmIfVpcNrp tables. |
| atmIfVpcNrpProvTable | 1.3.6.1.4.1.562.2.4.1.114.4.4.100 | not-accessible | This group contains the provisionable attributes for the Nrp component. | |
| atmIfVpcNrpProvEntry | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1 | not-accessible | An entry in the atmIfVpcNrpProvTable. | |
| LIN atmIfVpcNrpNextHop | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.10 | Link | read-write | This attribute specifies the Nrp component with which this Nrp is associated. A sample value is AtmIf/31 Vcc/0.32 Nrp. |
| INT atmIfVpcNrpConnectionPointType | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.20 | INTEGER | read-write | This attribute specifies the connection point type desired for a Nrp component. The actual connection point type value is visible in the parent component's connectionPointType attribute. The desired connection point type can be specified directly as a segmentEndPoint or connectingPoint. If autoConfigure is specified, the switch will select the connection point type based on the type attribute of the associated AtmIf, choosing segmentEndPoint for a UNI-type ATM interface and connectingPoint for a PPI-type ATM interface. It is obsoleted. The value is mapped into oamSegmentBoundary attribute. segmentEndPoint is mapped into yes. connectingPoint is mapped into no. autoConfigure is mapped into sameAsInterface. |
| INT atmIfVpcNrpOamSegmentBoundary | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.30 | INTEGER | read-write | This attribute specifies the OAM segment boundary desired for a Nrp component. It affects the connection point type value visible in the parent component's connectionPointType attribute. The desired OAM segment boundary can be specified directly as yes, no or sameAsInterface. If sameAsInterface is specified, the OAM segment boundary is same as the oamSegmentBoundary attribute of the associated AtmIf and the switch will set the connectionPointType, choosing segmentEndPoint for a segment- boundary ATM interface and connectingPoint for a non-segment- boundary ATM interface. |
| INT atmIfVpcNrpTxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.31 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the transmit direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion. This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the transmit direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVpcNrpRxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.32 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the receive direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion or usage parameter control (UPC). This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the receive direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the receive direction. When this attribute is set to sameAsTx, the PPD feature for traffic in the receive direction will be configured the same way as it is in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVpcNrpBandwidthElastic | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.33 | INTEGER | read-write | This attribute is only of importance for connections which are carried on a link with a variable bandwidth. For example, the bandwidth may be reduced in the event that one or more physical links in the IMA group fail, such that the originally requested bandwidth cannot be maintained. This attribute shows whether the application running on this connection can continue to operate if the bandwidth is reduced. If the bandwidth is reduced, the amount by which it is reduced will be displayed in the bandwidthReduction attribute. A value of yes, indicates that this connection is elastic, and the bandwidth may be reduced but the connection will not be released. Currently, this attribute should only be set to yes for situations where this Nrp is functioning as a loopback on one side of an IMA link. There are no other situations where this setting is valid. A value of no indicates that the bandwidth for this connection will not be reduced in the event of link bandwidth reduction. However, this connection may be released based on its holdingPriority. |
| INT atmIfVpcNrpOverrideHoldingPriority | 1.3.6.1.4.1.562.2.4.1.114.4.4.100.1.34 | INTEGER | read-write | This attribute specifies the holding priority of this connection. Holding priority is used when there is an IMA group where some physical links have failed. Holding priority determines the order in which connections are released. 4 is the lowest holding priority and is released first. 0 is a higher priority and is released last. The value specified in this attribute will override whatever holdingPriority that has been provisioned at the Vcd (or Vpd). If the value is left at the default of noOverride, the holdingPriority provisioned at the Vcd (or Vpd) will be used. |
| atmIfVccNrp | 1.3.6.1.4.1.562.2.4.1.114.5.4 | |||
| atmIfVccNrpRowStatusTable | 1.3.6.1.4.1.562.2.4.1.114.5.4.1 | not-accessible | This entry controls the addition and deletion of atmIfVccNrp components. | |
| atmIfVccNrpRowStatusEntry | 1.3.6.1.4.1.562.2.4.1.114.5.4.1.1 | not-accessible | A single entry in the table represents a single atmIfVccNrp component. | |
| ROW atmIfVccNrpRowStatus | 1.3.6.1.4.1.562.2.4.1.114.5.4.1.1.1 | RowStatus | read-write | This variable is used as the basis for SNMP naming of atmIfVccNrp components. These components can be added and deleted. |
| STR atmIfVccNrpComponentName | 1.3.6.1.4.1.562.2.4.1.114.5.4.1.1.2 | DisplayString | read-only | This variable provides the component's string name for use with the ASCII Console Interface |
| STO atmIfVccNrpStorageType | 1.3.6.1.4.1.562.2.4.1.114.5.4.1.1.4 | StorageType | read-only | This variable represents the storage type value for the atmIfVccNrp tables. |
| NON atmIfVccNrpIndex | 1.3.6.1.4.1.562.2.4.1.114.5.4.1.1.10 | NonReplicated | not-accessible | This variable represents the index for the atmIfVccNrp tables. |
| atmIfVccNrpProvTable | 1.3.6.1.4.1.562.2.4.1.114.5.4.100 | not-accessible | This group contains the provisionable attributes for the Nrp component. | |
| atmIfVccNrpProvEntry | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1 | not-accessible | An entry in the atmIfVccNrpProvTable. | |
| LIN atmIfVccNrpNextHop | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.10 | Link | read-write | This attribute specifies the Nrp component with which this Nrp is associated. A sample value is AtmIf/31 Vcc/0.32 Nrp. |
| INT atmIfVccNrpConnectionPointType | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.20 | INTEGER | read-write | This attribute specifies the connection point type desired for a Nrp component. The actual connection point type value is visible in the parent component's connectionPointType attribute. The desired connection point type can be specified directly as a segmentEndPoint or connectingPoint. If autoConfigure is specified, the switch will select the connection point type based on the type attribute of the associated AtmIf, choosing segmentEndPoint for a UNI-type ATM interface and connectingPoint for a PPI-type ATM interface. It is obsoleted. The value is mapped into oamSegmentBoundary attribute. segmentEndPoint is mapped into yes. connectingPoint is mapped into no. autoConfigure is mapped into sameAsInterface. |
| INT atmIfVccNrpOamSegmentBoundary | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.30 | INTEGER | read-write | This attribute specifies the OAM segment boundary desired for a Nrp component. It affects the connection point type value visible in the parent component's connectionPointType attribute. The desired OAM segment boundary can be specified directly as yes, no or sameAsInterface. If sameAsInterface is specified, the OAM segment boundary is same as the oamSegmentBoundary attribute of the associated AtmIf and the switch will set the connectionPointType, choosing segmentEndPoint for a segment- boundary ATM interface and connectingPoint for a non-segment- boundary ATM interface. |
| INT atmIfVccNrpTxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.31 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the transmit direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion. This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the transmit direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVccNrpRxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.32 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the receive direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion or usage parameter control (UPC). This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the receive direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the receive direction. When this attribute is set to sameAsTx, the PPD feature for traffic in the receive direction will be configured the same way as it is in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVccNrpBandwidthElastic | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.33 | INTEGER | read-write | This attribute is only of importance for connections which are carried on a link with a variable bandwidth. For example, the bandwidth may be reduced in the event that one or more physical links in the IMA group fail, such that the originally requested bandwidth cannot be maintained. This attribute shows whether the application running on this connection can continue to operate if the bandwidth is reduced. If the bandwidth is reduced, the amount by which it is reduced will be displayed in the bandwidthReduction attribute. A value of yes, indicates that this connection is elastic, and the bandwidth may be reduced but the connection will not be released. Currently, this attribute should only be set to yes for situations where this Nrp is functioning as a loopback on one side of an IMA link. There are no other situations where this setting is valid. A value of no indicates that the bandwidth for this connection will not be reduced in the event of link bandwidth reduction. However, this connection may be released based on its holdingPriority. |
| INT atmIfVccNrpOverrideHoldingPriority | 1.3.6.1.4.1.562.2.4.1.114.5.4.100.1.34 | INTEGER | read-write | This attribute specifies the holding priority of this connection. Holding priority is used when there is an IMA group where some physical links have failed. Holding priority determines the order in which connections are released. 4 is the lowest holding priority and is released first. 0 is a higher priority and is released last. The value specified in this attribute will override whatever holdingPriority that has been provisioned at the Vcd (or Vpd). If the value is left at the default of noOverride, the holdingPriority provisioned at the Vcd (or Vpd) will be used. |
| atmIfVptVccNrp | 1.3.6.1.4.1.562.2.4.1.114.9.20.4 | |||
| atmIfVptVccNrpRowStatusTable | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1 | not-accessible | This entry controls the addition and deletion of atmIfVptVccNrp components. | |
| atmIfVptVccNrpRowStatusEntry | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1.1 | not-accessible | A single entry in the table represents a single atmIfVptVccNrp component. | |
| ROW atmIfVptVccNrpRowStatus | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1.1.1 | RowStatus | read-write | This variable is used as the basis for SNMP naming of atmIfVptVccNrp components. These components can be added and deleted. |
| STR atmIfVptVccNrpComponentName | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1.1.2 | DisplayString | read-only | This variable provides the component's string name for use with the ASCII Console Interface |
| STO atmIfVptVccNrpStorageType | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1.1.4 | StorageType | read-only | This variable represents the storage type value for the atmIfVptVccNrp tables. |
| NON atmIfVptVccNrpIndex | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.1.1.10 | NonReplicated | not-accessible | This variable represents the index for the atmIfVptVccNrp tables. |
| atmIfVptVccNrpProvTable | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100 | not-accessible | This group contains the provisionable attributes for the Nrp component. | |
| atmIfVptVccNrpProvEntry | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1 | not-accessible | An entry in the atmIfVptVccNrpProvTable. | |
| LIN atmIfVptVccNrpNextHop | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.10 | Link | read-write | This attribute specifies the Nrp component with which this Nrp is associated. A sample value is AtmIf/31 Vcc/0.32 Nrp. |
| INT atmIfVptVccNrpConnectionPointType | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.20 | INTEGER | read-write | This attribute specifies the connection point type desired for a Nrp component. The actual connection point type value is visible in the parent component's connectionPointType attribute. The desired connection point type can be specified directly as a segmentEndPoint or connectingPoint. If autoConfigure is specified, the switch will select the connection point type based on the type attribute of the associated AtmIf, choosing segmentEndPoint for a UNI-type ATM interface and connectingPoint for a PPI-type ATM interface. It is obsoleted. The value is mapped into oamSegmentBoundary attribute. segmentEndPoint is mapped into yes. connectingPoint is mapped into no. autoConfigure is mapped into sameAsInterface. |
| INT atmIfVptVccNrpOamSegmentBoundary | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.30 | INTEGER | read-write | This attribute specifies the OAM segment boundary desired for a Nrp component. It affects the connection point type value visible in the parent component's connectionPointType attribute. The desired OAM segment boundary can be specified directly as yes, no or sameAsInterface. If sameAsInterface is specified, the OAM segment boundary is same as the oamSegmentBoundary attribute of the associated AtmIf and the switch will set the connectionPointType, choosing segmentEndPoint for a segment- boundary ATM interface and connectingPoint for a non-segment- boundary ATM interface. |
| INT atmIfVptVccNrpTxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.31 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the transmit direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion. This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the transmit direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVptVccNrpRxAal5PartialPacketDiscard | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.32 | INTEGER | read-write | This attribute is obsolete in P4.2 and has been migrated under Vcd (Vpd) component. This attribute specifies whether the AAL5 Partial Packet Discard (PPD) feature has been enabled or disabled on the Nrp in the receive direction. This feature allows the NRP to discard the remainder of a cell-forwarded AAL5 frame if a cell of this frame has been discarded due to congestion or usage parameter control (UPC). This increases the 'goodput' of the link, since cells which are only going to be discarded by the AAL5 reassembly are not transmitted. When this attribute is set to enabled, the PPD feature is applied in the receive direction. It should only be enabled for connections whose end points are performing AAL5 segmentation and reassembly. When this attribute is set to disabled, the PPD feature is not applied to traffic for this connection in the receive direction. When this attribute is set to sameAsTx, the PPD feature for traffic in the receive direction will be configured the same way as it is in the transmit direction. Note that specifying enabled for a non-AAL5 connection will cause all traffic to be discarded once congestion is encountered. |
| INT atmIfVptVccNrpBandwidthElastic | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.33 | INTEGER | read-write | This attribute is only of importance for connections which are carried on a link with a variable bandwidth. For example, the bandwidth may be reduced in the event that one or more physical links in the IMA group fail, such that the originally requested bandwidth cannot be maintained. This attribute shows whether the application running on this connection can continue to operate if the bandwidth is reduced. If the bandwidth is reduced, the amount by which it is reduced will be displayed in the bandwidthReduction attribute. A value of yes, indicates that this connection is elastic, and the bandwidth may be reduced but the connection will not be released. Currently, this attribute should only be set to yes for situations where this Nrp is functioning as a loopback on one side of an IMA link. There are no other situations where this setting is valid. A value of no indicates that the bandwidth for this connection will not be reduced in the event of link bandwidth reduction. However, this connection may be released based on its holdingPriority. |
| INT atmIfVptVccNrpOverrideHoldingPriority | 1.3.6.1.4.1.562.2.4.1.114.9.20.4.100.1.34 | INTEGER | read-write | This attribute specifies the holding priority of this connection. Holding priority is used when there is an IMA group where some physical links have failed. Holding priority determines the order in which connections are released. 4 is the lowest holding priority and is released first. 0 is a higher priority and is released last. The value specified in this attribute will override whatever holdingPriority that has been provisioned at the Vcd (or Vpd). If the value is left at the default of noOverride, the holdingPriority provisioned at the Vcd (or Vpd) will be used. |
| atmBearerServiceMIB | 1.3.6.1.4.1.562.2.4.2.64 | |||
| atmBearerServiceGroup | 1.3.6.1.4.1.562.2.4.2.64.1 | |||
| atmBearerServiceGroupBE | 1.3.6.1.4.1.562.2.4.2.64.1.5 | |||
| atmBearerServiceGroupBE00 | 1.3.6.1.4.1.562.2.4.2.64.1.5.1 | |||
| atmBearerServiceGroupBE00A | 1.3.6.1.4.1.562.2.4.2.64.1.5.1.2 | |||
| atmBearerServiceCapabilities | 1.3.6.1.4.1.562.2.4.2.64.3 | |||
| atmBearerServiceCapabilitiesBE | 1.3.6.1.4.1.562.2.4.2.64.3.5 | |||
| atmBearerServiceCapabilitiesBE00 | 1.3.6.1.4.1.562.2.4.2.64.3.5.1 | |||
| atmBearerServiceCapabilitiesBE00A | 1.3.6.1.4.1.562.2.4.2.64.3.5.1.2 |
RFC description
Vendor-specific MIB for Nortel Magellan Passport ATM bearer service management; manages ATM virtual circuits, traffic contracts, and bearer service provisioning.
Start monitoring Nortel Magellan Passport ATM/WAN switch (ATM bearer service NRP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.