| OID symbolic | OID numeric | Type | Access | Description |
|---|
| INT ntnQos802FilterDscp | 1.3.6.1.4.1.45.4.4.1.3.1.1.1 | INTEGER | read-create | The value that the DSCP in the packet can have and
match this filter. A value of -1 indicates that a specific
DSCP value has not been defined and thus all DSCP values
are considered a match. |
| INT ntnQos802FilterDstL4PortMax | 1.3.6.1.4.1.45.4.4.1.3.1.1.4 | INTEGER | read-create | The maximum value that the packet's layer 4 destination
port number can have and match this filter. Valid only
when applied against IP traffic flows. The value of
this attribute must be greater-than-or-equal-to the value
of the corresponding ntnQos802FilterDstL4PortMin attribute. |
| INT ntnQos802FilterDstL4PortMin | 1.3.6.1.4.1.45.4.4.1.3.1.1.3 | INTEGER | read-create | The minimum value that the packet's layer 4 destination
port number can have and match this filter. Valid only
when applied against IP traffic flows. The value of
this attribute must be less-than-or-equal-to the value of
the corresponding ntnQos802FilterDstL4PortMax attribute. |
| ntnQos802FilterExt | 1.3.6.1.4.1.45.4.4.1.3 | | | |
| ntnQos802FilterExtEntry | 1.3.6.1.4.1.45.4.4.1.3.1.1 | | not-accessible | Global (802) filter extensions. Each entry specifies an
instance of the ntnQos802FilterExt class which describes
(potentially) several distinct filter attributes.
An instance of this class can not be deleted while the
correspond qos802AceTable instance exists. |
| ntnQos802FilterExtGroup | 1.3.6.1.4.1.45.4.4.2.2.5 | | | Objects from the ntnQos802FilterExtTable. |
| ntnQos802FilterExtTable | 1.3.6.1.4.1.45.4.4.1.3.1 | | not-accessible | Contains the current set of configured 802 filter
extensions. |
| INT ntnQos802FilterProtocol | 1.3.6.1.4.1.45.4.4.1.3.1.1.2 | INTEGER | read-create | The IP protocol to match against the packet's protocol.
Valid only when applied against IP traffic. A value of
zero means match all. |
| INT ntnQos802FilterSrcL4PortMax | 1.3.6.1.4.1.45.4.4.1.3.1.1.6 | INTEGER | read-create | The maximum value that the packet's layer 4 source port
number can have and match this filter. Valid only
when applied against IP traffic flows. The value of this
attribute must be greater-than-or-equal-to the value of
the corresponding ntnQos802FilterSrcL4PortMin attribute. |
| INT ntnQos802FilterSrcL4PortMin | 1.3.6.1.4.1.45.4.4.1.3.1.1.5 | INTEGER | read-create | The minimum value that the packet's layer 4 source port
number can have and match this filter. Valid only
when applied against IP traffic flows. The value of this
attribute must be less-than-or-equal-to the value of
the corresponding ntnQos802FilterSrcL4PortMax attribute. |
| OCT ntnQos802FilterVlanIdSet | 1.3.6.1.4.1.45.4.4.1.3.1.1.7 | OCTET STRING | read-create | This attribute is used to specify a set of VLAN IDs
against which the traffic being classified is compared.
Packets that contain a VLAN ID equal to one of the VLAN
IDs in this set match this component of an 802 filter.
The format of this octet string is a series of two-byte
(16 bit) values with each octet tuple identifying a
single VLAN ID in the set. Therefore, the length of the
octet string value of this object is always either zero
or an even number of octets (e.g., 2, 4, 6, 20). As with
most sets, ordering within the set (octet string) is
unimportant. For example, a set specifying three VLAN
IDs (8, 35 and 4012) might be specified as follows:
Octets: 1 | 2 | 3 | 4 | 5 | 6
------------------------------------------------
Values: 0x00 | 0x23 | 0x00 | 0x08 | 0x0F | 0xAC
------------------------------------------------
VLAN ID: 35 | 8 | 4012
The supported maximum length of this attribute depends
on the maximum number of VLANs that may be included in
a set for filtering purposes. This length is thus
implementation dependent.
Note that this attribute and the qos802AceVlanId
attribute are mutually exclusive. The value of the
qos802AceVlanId component of the augmented filter
entry must be set to 'ignore' (i.e., -1) if the length
of this set is non-zero. Otherwise entry creation will
fail. |
| ntnQosActionExt | 1.3.6.1.4.1.45.4.4.1.2 | | | |
| INT ntnQosActionExtAssignFlowId | 1.3.6.1.4.1.45.4.4.1.2.1.1.1 | INTEGER | read-create | This action attribute, when specified, will cause
the packet being evaluated to be associated with the
specified flow identifier. Flow identifiers may be
used to facilitate traffic shaping and other
implementation specific operations at the egress
interface.
Setting this attribute to -1 indicates that flow
identification is not in use at the present time. |
| T/F ntnQosActionExtCopyToCpu | 1.3.6.1.4.1.45.4.4.1.2.1.1.2 | TruthValue | read-create | This action attribute, when specified, will cause
the packet being evaluated to be sent to the CPU
for further processing. Extreme care should be taken
when setting this object to 'true(1)' since this action
may adversely affect resource availability in the
system impacting overall system operation.
A value of 'false(2)' indicates that this action will
not be initiated. |
| ntnQosActionExtEntry | 1.3.6.1.4.1.45.4.4.1.2.1.1 | | not-accessible | General action extensions. Each entry specifies an instance
of the ntnQosActionExt class which describes (potentially)
several distinct action attributes. Each action is taken
individually regarding the data in question. Several actions
can be taken for a single frame.
An instance of this class can not be deleted while the
correspond qosActionTable instance exists. |
| ntnQosActionExtGroup | 1.3.6.1.4.1.45.4.4.2.2.4 | | | Objects from the ntnQosActionExtTable. |
| INT ntnQosActionExtMirrorDirection | 1.3.6.1.4.1.45.4.4.1.2.1.1.6 | INTEGER | read-create | This action attribute, when specified, will determine
where a snapshot of a packet being mirrored will be
taken for mirroring purposes. The packet that was
'received' by the device will be mirrored (i.e., packet
modifications that may occur during processing will not
appear in the mirrored data) when the direction attribute
has the value 'ingress(1)'. The packet that is to be
'transmitted' by the device will be mirrored (i.e., packet
modifications that may occur during processing will appear
in the mirrored data) when the direction attribute has
the value 'egress(2)'.
Note that the value of this attribute is only considered
if the ntnQosActionExtMirrorFrame attribute is 'true'. |
| T/F ntnQosActionExtMirrorFrame | 1.3.6.1.4.1.45.4.4.1.2.1.1.3 | TruthValue | read-create | This action attribute, when specified, will cause
the packet being evaluated to be sent to a predefined
egress port for transmission in addition to the normal
processing associated with the packet.
Specification of the egress port or ports that will
serve as the destination for mirrored data is beyond
the scope of this document. Furthermore, note that
data mirroring can potentially consume substantial
resources at the egress. Oversubscription issues
should be considered prior to specifying this action.
Also note that the mirroring direction attribute in
this same ntnQosActionExt entry determines the
data that is mirrored. The packet that was 'received'
by the device will be mirrored (i.e., packet
modifications that may occur during processing will
not appear in the mirrored data) when the mirroring
direction attribute has the value 'ingress(1)'. The
packet that is to be 'transmitted' by the device will
be mirrored (i.e., packet modifications that may occur
during processing will appear in the mirrored data)
when the mirroring direction attribute has the value
'egress(2)'.
A value of 'false(2)' indicates that this action will
not be initiated. |
| INT ntnQosActionExtSetDropPrec | 1.3.6.1.4.1.45.4.4.1.2.1.1.4 | INTEGER | read-create | This action attribute, when specified, will cause
the packet being evaluated to be associated with the
specified relative drop precedence. The relative drop
precedence may be used to determine traffic
precedence relative to other traffic being processed
by the device and other implementation specific
operations at the egress interface.
A low value for drop precedence equates to the traffic
receiving a higher priority in terms of processing.
In other words, traffic with a drop precedence of 1
is treated with the highest processing priority while
traffic with a drop precedence of 8 receives the
lowest processing priority.
Specifying a value equal to useDefault(9) means that
the value for this attribute will be assigned based
on default information maintained in the system. The
value specified in the 'UpdateDSCP' attribute will
be used to determine the default drop precedence. Note
that specifying useDefault(9) means that assignment
of a value for this attribute is implementation
dependent.
Specifying a value equal to ignore(10) means that
no action will be taken related to this attribute.
Note that the results of classification where
actions specifying ignore(10) are applied are
implementation dependent.
Specifying a value equal to useEgressMap(11) means that
the value for this attribute will be assigned based
on DSCP-to-drop precedence egress map information
maintained in the system. The DSCP value in received
traffic will be used to determine the drop precedence.
Note that specifying useEgressMap(11) means that assignment
of a value for this attribute is implementation
dependent. |
| ntnQosActionExtTable | 1.3.6.1.4.1.45.4.4.1.2.1 | | not-accessible | Contains the current set of configured general action
extensions. The actions are associated with all types
ACLs during operation. |
| INT ntnQosActionExtUpdatePri | 1.3.6.1.4.1.45.4.4.1.2.1.1.5 | INTEGER | read-create | This action attribute, when specified, will cause the
value contained in the user priority field of the 802.1Q
frame to be updated based on the value of this object.
No action is taken if the frame is untagged.
Specifying a value equal to useDefault(9) means that
the value for this attribute will be assigned based
on default information maintained in the system. The
value specified in the 'UpdateDSCP' attribute will
be used to determine the default drop precedence. Note
that specifying useDefault(9) means that assignment
of a value for this attribute is implementation
dependent.
Specifying a value equal to ignore(10) means that
no action will be taken related to this attribute.
Note that the results of classification where
actions specifying ignore(10) are applied are
implementation dependent.
Specifying a value equal to useEgressMap(11) means that
the value for this attribute will be assigned based
on DSCP-to-drop precedence egress map information
maintained in the system. The DSCP value in received
traffic will be used to determine the drop precedence.
Note that specifying useEgressMap(11) means that assignment
of a value for this attribute is implementation
dependent. |
| DRO ntnQosIfDscpMappingExtDropPrec | 1.3.6.1.4.1.45.4.4.1.1.3.1.1 | DropPrecedence | read-create | The drop precedence value to use for traffic with the
associated DSCP value. |
| ntnQosIfDscpMappingExtEntry | 1.3.6.1.4.1.45.4.4.1.1.3.1 | | not-accessible | An instance of the ntnQosIfDscpMappingExt class. |
| ntnQosIfDscpMappingExtGroup | 1.3.6.1.4.1.45.4.4.2.2.3 | | | Objects from the ntnQosIfDscpMappingExtTable. |
| ntnQosIfDscpMappingExtTable | 1.3.6.1.4.1.45.4.4.1.1.3 | | not-accessible | Supports augmenting the information regarding
the mapping of DSCP values to 802.1p user priority
and drop precedence values. |
| ntnQosIfParametersExt | 1.3.6.1.4.1.45.4.4.1.1 | | | |
| ntnQosIfPriAssignmentEntry | 1.3.6.1.4.1.45.4.4.1.1.1.1 | | not-accessible | An instance of the ntnQosIfPriAssignment class. |
| ntnQosIfPriAssignmentGroup | 1.3.6.1.4.1.45.4.4.2.2.1 | | | Objects from the ntnQosIfPriAssignmentTable. |
| POL ntnQosIfPriAssignmentId | 1.3.6.1.4.1.45.4.4.1.1.1.1.1 | PolicyInstanceId | not-accessible | An index that is used to uniquely identify the
instance of the ntnQosIfPriAssignment class. |
| QOS ntnQosIfPriAssignmentPri | 1.3.6.1.4.1.45.4.4.1.1.1.1.3 | QosIeee802Cos | read-create | The 802.1D user priority to which this class
instance applies. |
| NUM ntnQosIfPriAssignmentQueue | 1.3.6.1.4.1.45.4.4.1.1.1.1.4 | QosInterfaceQueueCount | read-create | The specific queue, within the queue set that is
associated with the interface set identified by the
ntnQosIfPriAssignmentRoles tag, on which traffic
with the specified user priority, dictated by the
ntnQosIfPriAssignmentPri value, is placed. Failure
to specify an appropriate queue results in a
'priAssociationConflict(4)' error indication being
returned. |
| ROL ntnQosIfPriAssignmentRoles | 1.3.6.1.4.1.45.4.4.1.1.1.1.2 | RoleCombination | read-create | The role combination with which an interface must be
configured to support the Pri-to-queue assignment
described by this instance. The specified role
combination must be defined in the qosInterfaceType
table prior to being referenced by this entry.
Otherwise a 'priAssociationUnknown(3)' error code
will be returned. |
| ROW ntnQosIfPriAssignmentStatus | 1.3.6.1.4.1.45.4.4.1.1.1.1.6 | RowStatus | read-create | The status of this row.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value. Row
creation using only default values is supported. |
| STO ntnQosIfPriAssignmentStorageType | 1.3.6.1.4.1.45.4.4.1.1.1.1.5 | StorageType | read-create | The storage type for this conceptual row.
Conceptual rows having the value permanent(4) need not
allow write-access to any columnar objects in the row.
This object may not be modified if the associated
ntnQosIfPriAssignmentStatus object is equal to active(1). |
| ntnQosIfPriAssignmentTable | 1.3.6.1.4.1.45.4.4.1.1.1 | | not-accessible | Supports the assignment of 802.1D user priority
values to a queue for each interface with a specific
role combination. There will be 8 instances of this
class for each supported role combination. |
| ntnQosInterfaceTypeExtEntry | 1.3.6.1.4.1.45.4.4.1.1.2.1 | | not-accessible | An instance of the ntnQosInterfaceTypeExt class. |
| ntnQosInterfaceTypeExtGroup | 1.3.6.1.4.1.45.4.4.2.2.2 | | | Objects from the ntnQosInterfaceTypeExtTable. |
| INT ntnQosInterfaceTypeExtIfClass | 1.3.6.1.4.1.45.4.4.1.1.2.1.1 | INTEGER | read-create | A value describing the overall classification of
traffic received on interfaces with the given role
combination. Traffic received on core (i.e., trusted)
interfaces may be processed differently and be subject
to different restrictions that traffic received on
access (i.e., non-trusted) interfaces. The treatment
of traffic based on interface class is implementation
dependent. |
| ntnQosInterfaceTypeExtTable | 1.3.6.1.4.1.45.4.4.1.1.2 | | not-accessible | Supports augmenting the information regarding
the interface roles and queue set assignments. |
| ntnQosPolicyExtPib | 1.3.6.1.4.1.45.4.4 | | | The Nortel Network's PIB module containing
extensions to the base PIB modules (Framework,
IP QoS, 802 QoS) produced by the IETF. |
| ntnQosPolicyExtPibClasses | 1.3.6.1.4.1.45.4.4.1 | | | |
| ntnQosPolicyExtPibCompliance | 1.3.6.1.4.1.45.4.4.2.1.1 | | | Describes the requirements for conformance to the
Nortel Networks QoS Policy Extension PIB. |
| ntnQosPolicyExtPibCompliances | 1.3.6.1.4.1.45.4.4.2.1 | | | |
| ntnQosPolicyExtPibConformance | 1.3.6.1.4.1.45.4.4.2 | | | |
| ntnQosPolicyExtPibGroups | 1.3.6.1.4.1.45.4.4.2.2 | | | |
