MWRM-PM-MIB

All MIBs › MWRM-PM-MIB

Category: Microwave/Radio

Description: Monitors microwave radio module performance metrics and threshold crossing alerts.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is MWRM-PM-MIB?

MWRM-PM-MIB is the performance-monitoring companion to the MWRM microwave radio equipment family, defining objects that record radio-link signal-quality statistics over fixed measurement intervals such as 15-minute bins. It exposes performance data specific to the RF unit (RFU) of a microwave link, most notably received signal level (RSL) and transmitted signal level (TSL) minimum/maximum values along with counts of threshold-crossing events when levels exceed configured limits. This is squarely a hardware/RF-link health monitoring MIB: it lets an operator track the radio's signal strength trends and catch degrading link quality, such as from fading or misalignment, before it causes an outage, functioning like a performance-counter MIB for a wireless link. It shares the genEquip/genEquipUnit equipment-indexing convention with MWRM-NETWORK-MIB, indicating both modules describe the same physical radio units. It is deployed in microwave backhaul networks where NOC teams continuously trend RSL/TSL performance to plan maintenance and detect fading link margins. Engineers can download the MWRM-PM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in MWRM-PM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

microwave radio link terminal (RF unit)
telecom backhaul radio equipment

Monitoring Examples

A NOC engineer polls genEquipPmRfuCommonSL15minMinRsl and genEquipPmRfuCommonSL15minMaxRsl from genEquipPmRfuCommonSL15minTable to trend the receive signal level swing on a given radio hop each interval, keyed by genEquipPmRfuCommonSL15minIfIndex. A rising count in genEquipPmRfuCommonSL15minRslExceed1/RslExceed2 signals the link crossed a configured RSL threshold, and combined with genEquipPmRfuCommonSL15minTimeAndDate pinpoints when signal fading occurred. Similarly, genEquipPmRfuCommonSL15minMinTsl/MaxTsl and TslExceed counters reveal transmit-power instability at the far end.

What Can Be Monitored

received signal level (RSL) min/max per interval
transmitted signal level (TSL) min/max per interval
RSL threshold-crossing event counts
TSL threshold-crossing event counts
15-minute performance interval timestamp

Imported Objects

From MWRM-RADIO-MIB

genEquipRadioCfgRadioId

OBJECT-TYPE

From MWRM-UNIT-MIB

AllowedNotAllowed
BerLevel
ClockSrc
DownUp
EnableDisable
EnableDisableSMI2
GreenYellow
HalfFull
InputSeverity
Integrity
LoopbackType
MetricImperial
NoYes
OffOn
PmTableType
ProgressStatus
QueueName
RadioId
RateMbps
RfuId
Severity
SignalLevel
SlotId
SwCommand
SwCommandTimer
TrailIfType
TrailProtectedType

From RFC-1215

TRAP-TYPE

From RFC1213-MIB

DisplayString
ifIndex

From SNMPv2-SMI

Counter32
Counter64
Gauge32
IpAddress
OBJECT-TYPE
enterprises

From SNMPv2-TC

MacAddress
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
microwave_radio	1.3.6.1.4.1.2281
genEquip	1.3.6.1.4.1.2281.10
genEquipUnit	1.3.6.1.4.1.2281.10.1
genEquipPM	1.3.6.1.4.1.2281.10.6
genEquipPmRfu	1.3.6.1.4.1.2281.10.6.1
genEquipPmRfuCommon	1.3.6.1.4.1.2281.10.6.1.1
genEquipPmRfuCommonSL15minTable	1.3.6.1.4.1.2281.10.6.1.1.1		not-accessible	This table indicates the RFU Signal Level PM data.
genEquipPmRfuCommonSL15minEntry	1.3.6.1.4.1.2281.10.6.1.1.1.1		not-accessible	Entry containing the data of the RFU SL PM.
INT genEquipPmRfuCommonSL15minId	1.3.6.1.4.1.2281.10.6.1.1.1.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmRfuCommonSL15minIfIndex	1.3.6.1.4.1.2281.10.6.1.1.1.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmRfuCommonSL15minTimeAndDate	1.3.6.1.4.1.2281.10.6.1.1.1.1.3	DisplayString	read-only	This value indicates the Time and date for the specific PM.
INT genEquipPmRfuCommonSL15minMinRsl	1.3.6.1.4.1.2281.10.6.1.1.1.1.4	INTEGER	read-only	This value indicates the minimum RSL value.
INT genEquipPmRfuCommonSL15minMaxRsl	1.3.6.1.4.1.2281.10.6.1.1.1.1.5	INTEGER	read-only	This value indicates the maximum RSL value.
INT genEquipPmRfuCommonSL15minRslExceed1	1.3.6.1.4.1.2281.10.6.1.1.1.1.6	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 1.
INT genEquipPmRfuCommonSL15minRslExceed2	1.3.6.1.4.1.2281.10.6.1.1.1.1.7	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 2.
INT genEquipPmRfuCommonSL15minMinTsl	1.3.6.1.4.1.2281.10.6.1.1.1.1.8	INTEGER	read-only	This value indicates the Min TSL value.
INT genEquipPmRfuCommonSL15minMaxTsl	1.3.6.1.4.1.2281.10.6.1.1.1.1.9	INTEGER	read-only	This value indicates the Max TSL value.
INT genEquipPmRfuCommonSL15minTslExceed	1.3.6.1.4.1.2281.10.6.1.1.1.1.10	INTEGER	read-only	This value indicates the number of seconds TSL exceeded the threshold
NUM genEquipPmRfuCommonSL15minIDF	1.3.6.1.4.1.2281.10.6.1.1.1.1.11	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmRfuCommonSL15minCurrTable	1.3.6.1.4.1.2281.10.6.1.1.2		not-accessible	This table indicates the RFU Signal Level PM data for the current 15 min. interval.
genEquipPmRfuCommonSL15minCurrEntry	1.3.6.1.4.1.2281.10.6.1.1.2.1		not-accessible	Entry containing the data of the Rfu SL PM.
INT genEquipPmRfuCommonSL15minCurrId	1.3.6.1.4.1.2281.10.6.1.1.2.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmRfuCommonSL15minCurrIfIndex	1.3.6.1.4.1.2281.10.6.1.1.2.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmRfuCommonSL15minCurrTimeAndDate	1.3.6.1.4.1.2281.10.6.1.1.2.1.3	DisplayString	read-only	This value indicates the Time and date for the specific PM.
INT genEquipPmRfuCommonSL15minCurrMinRsl	1.3.6.1.4.1.2281.10.6.1.1.2.1.4	INTEGER	read-only	This value indicates the minimum RSL value.
INT genEquipPmRfuCommonSL15minCurrMaxRsl	1.3.6.1.4.1.2281.10.6.1.1.2.1.5	INTEGER	read-only	This value indicates the maximum RSL value.
INT genEquipPmRfuCommonSL15minCurrRslExceed1	1.3.6.1.4.1.2281.10.6.1.1.2.1.6	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 1.
INT genEquipPmRfuCommonSL15minCurrRslExceed2	1.3.6.1.4.1.2281.10.6.1.1.2.1.7	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 2.
INT genEquipPmRfuCommonSL15minCurrMinTsl	1.3.6.1.4.1.2281.10.6.1.1.2.1.8	INTEGER	read-only	This value indicates the Min TSL value.
INT genEquipPmRfuCommonSL15minCurrMaxTsl	1.3.6.1.4.1.2281.10.6.1.1.2.1.9	INTEGER	read-only	This value indicates the Max TSL value.
INT genEquipPmRfuCommonSL15minCurrTslExceed	1.3.6.1.4.1.2281.10.6.1.1.2.1.10	INTEGER	read-only	This value indicates the number of seconds TSL exceeded the threshold
NUM genEquipPmRfuCommonSL15minCurrIDF	1.3.6.1.4.1.2281.10.6.1.1.2.1.11	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the current interval. integrity(0), nointegrity(1).
genEquipPmRfuCommonSL24hrTable	1.3.6.1.4.1.2281.10.6.1.1.3		not-accessible	This table indicates the RFU Signal Level 24 hr PM data.
genEquipPmRfuCommonSL24hrEntry	1.3.6.1.4.1.2281.10.6.1.1.3.1		not-accessible	Entry containing the data of the RFU SL PM.
INT genEquipPmRfuCommonSL24hrId	1.3.6.1.4.1.2281.10.6.1.1.3.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmRfuCommonSL24hrIfIndex	1.3.6.1.4.1.2281.10.6.1.1.3.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmRfuCommonSL24hrTimeAndDate	1.3.6.1.4.1.2281.10.6.1.1.3.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmRfuCommonSL24hrMinRsl	1.3.6.1.4.1.2281.10.6.1.1.3.1.4	INTEGER	read-only	This value indicates the min RSL value.
INT genEquipPmRfuCommonSL24hrMaxRsl	1.3.6.1.4.1.2281.10.6.1.1.3.1.5	INTEGER	read-only	This value indicates the max RSL value.
INT genEquipPmRfuCommonSL24hrRslExceed1	1.3.6.1.4.1.2281.10.6.1.1.3.1.6	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 1.
INT genEquipPmRfuCommonSL24hrRslExceed2	1.3.6.1.4.1.2281.10.6.1.1.3.1.7	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 2.
INT genEquipPmRfuCommonSL24hrMinTsl	1.3.6.1.4.1.2281.10.6.1.1.3.1.8	INTEGER	read-only	This value indicates the Min TSL value.
INT genEquipPmRfuCommonSL24hrMaxTsl	1.3.6.1.4.1.2281.10.6.1.1.3.1.9	INTEGER	read-only	This value indicates the Max TSL value.
INT genEquipPmRfuCommonSL24hrTslExceed	1.3.6.1.4.1.2281.10.6.1.1.3.1.10	INTEGER	read-only	This value indicates the number of seconds RSL exceeded the threshold
NUM genEquipPmRfuCommonSL24hrIDF	1.3.6.1.4.1.2281.10.6.1.1.3.1.11	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmRfuCommonSL24hrCurrTable	1.3.6.1.4.1.2281.10.6.1.1.4		not-accessible	This table indicates the RFU Signal Level PM data for the current 24 hour interval.
genEquipPmRfuCommonSL24hrCurrEntry	1.3.6.1.4.1.2281.10.6.1.1.4.1		not-accessible	Entry containing the data of the RFU SL PM.
INT genEquipPmRfuCommonSL24hrCurrId	1.3.6.1.4.1.2281.10.6.1.1.4.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmRfuCommonSL24hrCurrIfIndex	1.3.6.1.4.1.2281.10.6.1.1.4.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmRfuCommonSL24hrCurrTimeAndDate	1.3.6.1.4.1.2281.10.6.1.1.4.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmRfuCommonSL24hrCurrMinRsl	1.3.6.1.4.1.2281.10.6.1.1.4.1.4	INTEGER	read-only	This value indicates the min RSL value.
INT genEquipPmRfuCommonSL24hrCurrMaxRsl	1.3.6.1.4.1.2281.10.6.1.1.4.1.5	INTEGER	read-only	This value indicates the Max RSL value.
INT genEquipPmRfuCommonSL24hrCurrRslExceed1	1.3.6.1.4.1.2281.10.6.1.1.4.1.6	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 1.
INT genEquipPmRfuCommonSL24hrCurrRslExceed2	1.3.6.1.4.1.2281.10.6.1.1.4.1.7	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 2.
INT genEquipPmRfuCommonSL24hrCurrMinTsl	1.3.6.1.4.1.2281.10.6.1.1.4.1.8	INTEGER	read-only	This value indicates the Min TSL value.
INT genEquipPmRfuCommonSL24hrCurrMaxTsl	1.3.6.1.4.1.2281.10.6.1.1.4.1.9	INTEGER	read-only	This value indicates the Max TSL value.
INT genEquipPmRfuCommonSL24hrCurrTslExceed	1.3.6.1.4.1.2281.10.6.1.1.4.1.10	INTEGER	read-only	This value indicates the number of seconds TSL exceeded the threshold
NUM genEquipPmRfuCommonSL24hrCurrIDF	1.3.6.1.4.1.2281.10.6.1.1.4.1.11	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmTraffic	1.3.6.1.4.1.2281.10.6.2
genEquipPmTrafficRadioAgg15minTable	1.3.6.1.4.1.2281.10.6.2.1		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
genEquipPmTrafficRadioAgg15minEntry	1.3.6.1.4.1.2281.10.6.2.1.1		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
INT genEquipPmTrafficRadioAgg15minId	1.3.6.1.4.1.2281.10.6.2.1.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmTrafficRadioAgg15minIfIndex	1.3.6.1.4.1.2281.10.6.2.1.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmTrafficRadioAgg15minTimeAndDate	1.3.6.1.4.1.2281.10.6.2.1.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmTrafficRadioAgg15minES	1.3.6.1.4.1.2281.10.6.2.1.1.4	INTEGER	read-only	This value indicates the ES value.
INT genEquipPmTrafficRadioAgg15minSES	1.3.6.1.4.1.2281.10.6.2.1.1.5	INTEGER	read-only	This value indicates the SES value.
INT genEquipPmTrafficRadioAgg15minUAS	1.3.6.1.4.1.2281.10.6.2.1.1.6	INTEGER	read-only	This value indicates the UAS value.
INT genEquipPmTrafficRadioAgg15minBBE	1.3.6.1.4.1.2281.10.6.2.1.1.7	INTEGER	read-only	This value indicates the BBE value.
NUM genEquipPmTrafficRadioAgg15minIDF	1.3.6.1.4.1.2281.10.6.2.1.1.8	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmTrafficRadioAgg15minCurrTable	1.3.6.1.4.1.2281.10.6.2.2		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
genEquipPmTrafficRadioAgg15minCurrEntry	1.3.6.1.4.1.2281.10.6.2.2.1		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
INT genEquipPmTrafficRadioAgg15minCurrId	1.3.6.1.4.1.2281.10.6.2.2.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmTrafficRadioAgg15minCurrIfIndex	1.3.6.1.4.1.2281.10.6.2.2.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmTrafficRadioAgg15minCurrTimeAndDate	1.3.6.1.4.1.2281.10.6.2.2.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmTrafficRadioAgg15minCurrES	1.3.6.1.4.1.2281.10.6.2.2.1.4	INTEGER	read-only	This value indicates the ES value.
INT genEquipPmTrafficRadioAgg15minCurrSES	1.3.6.1.4.1.2281.10.6.2.2.1.5	INTEGER	read-only	This value indicates the SES value.
INT genEquipPmTrafficRadioAgg15minCurrUAS	1.3.6.1.4.1.2281.10.6.2.2.1.6	INTEGER	read-only	This value indicates the UAS value.
INT genEquipPmTrafficRadioAgg15minCurrBBE	1.3.6.1.4.1.2281.10.6.2.2.1.7	INTEGER	read-only	This value indicates the BBE value.
NUM genEquipPmTrafficRadioAgg15minCurrIDF	1.3.6.1.4.1.2281.10.6.2.2.1.8	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmTrafficRadioAgg24hrTable	1.3.6.1.4.1.2281.10.6.2.3		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
genEquipPmTrafficRadioAgg24hrEntry	1.3.6.1.4.1.2281.10.6.2.3.1		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
INT genEquipPmTrafficRadioAgg24hrId	1.3.6.1.4.1.2281.10.6.2.3.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmTrafficRadioAgg24hrIfIndex	1.3.6.1.4.1.2281.10.6.2.3.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmTrafficRadioAgg24hrTimeAndDate	1.3.6.1.4.1.2281.10.6.2.3.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmTrafficRadioAgg24hrES	1.3.6.1.4.1.2281.10.6.2.3.1.4	INTEGER	read-only	This value indicates the ES value.
INT genEquipPmTrafficRadioAgg24hrSES	1.3.6.1.4.1.2281.10.6.2.3.1.5	INTEGER	read-only	This value indicates the SES value.
INT genEquipPmTrafficRadioAgg24hrUAS	1.3.6.1.4.1.2281.10.6.2.3.1.6	INTEGER	read-only	This value indicates the UAS value.
INT genEquipPmTrafficRadioAgg24hrBBE	1.3.6.1.4.1.2281.10.6.2.3.1.7	INTEGER	read-only	This value indicates the BBE value.
NUM genEquipPmTrafficRadioAgg24hrIDF	1.3.6.1.4.1.2281.10.6.2.3.1.8	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the interval. integrity(0), nointegrity(1).
genEquipPmTrafficRadioAgg24hrCurrTable	1.3.6.1.4.1.2281.10.6.2.4		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
genEquipPmTrafficRadioAgg24hrCurrEntry	1.3.6.1.4.1.2281.10.6.2.4.1		not-accessible	This table indicates the Radio Aggregate PM data for all 15 min intervals.
INT genEquipPmTrafficRadioAgg24hrCurrId	1.3.6.1.4.1.2281.10.6.2.4.1.1	INTEGER	read-only	This value indicates an index of a specific RFU
INT genEquipPmTrafficRadioAgg24hrCurrIfIndex	1.3.6.1.4.1.2281.10.6.2.4.1.2	INTEGER	read-only	This value indicates the interface index of a specific RFU (as appears in the ifTable)
STR genEquipPmTrafficRadioAgg24hrCurrTimeAndDate	1.3.6.1.4.1.2281.10.6.2.4.1.3	DisplayString	read-only	This value indicates the time and date for the specific PM.
INT genEquipPmTrafficRadioAgg24hrCurrES	1.3.6.1.4.1.2281.10.6.2.4.1.4	INTEGER	read-only	This value indicates the ES value.
INT genEquipPmTrafficRadioAgg24hrCurrSES	1.3.6.1.4.1.2281.10.6.2.4.1.5	INTEGER	read-only	This value indicates the SES value.
INT genEquipPmTrafficRadioAgg24hrCurrUAS	1.3.6.1.4.1.2281.10.6.2.4.1.6	INTEGER	read-only	This value indicates the UAS value.
INT genEquipPmTrafficRadioAgg24hrCurrBBE	1.3.6.1.4.1.2281.10.6.2.4.1.7	INTEGER	read-only	This value indicates the BBE value.
NUM genEquipPmTrafficRadioAgg24hrCurrIDF	1.3.6.1.4.1.2281.10.6.2.4.1.8	Integrity	read-only	This value indicates the IDF (Invalid Data Flag) of the current interval. integrity(0), nointegrity(1).
genEquipPmAll	1.3.6.1.4.1.2281.10.6.3
OFF genEquipPmClear	1.3.6.1.4.1.2281.10.6.3.1	OffOn	read-write	Clear All values for PM tables.
genEquipPmTrafficSL	1.3.6.1.4.1.2281.10.6.3.2
genEquipPmTrafficSLTable	1.3.6.1.4.1.2281.10.6.3.2.1		not-accessible	This table indicates the RFU Signal Level PM data.
genEquipPmTrafficSLEntry	1.3.6.1.4.1.2281.10.6.3.2.1.1		not-accessible	Entry containing the data of the RFU signal level PM.
PMT genEquipPmTrafficSLPmType	1.3.6.1.4.1.2281.10.6.3.2.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
RFU genEquipPmTrafficSLId	1.3.6.1.4.1.2281.10.6.3.2.1.1.2	RfuId	read-only	This value indicates an index of a specific RFU
INT genEquipPmTrafficSLInterval	1.3.6.1.4.1.2281.10.6.3.2.1.1.3	INTEGER	read-only	This value indicates an index of a specific PM Interval
INT genEquipPmTrafficSLMinRsl	1.3.6.1.4.1.2281.10.6.3.2.1.1.4	INTEGER	read-only	This value indicates the min RSL value.
INT genEquipPmTrafficSLMaxRsl	1.3.6.1.4.1.2281.10.6.3.2.1.1.5	INTEGER	read-only	This value indicates the max RSL value.
INT genEquipPmTrafficSLRslExceed1	1.3.6.1.4.1.2281.10.6.3.2.1.1.6	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 1.
INT genEquipPmTrafficSLRslExceed2	1.3.6.1.4.1.2281.10.6.3.2.1.1.7	INTEGER	read-only	This value indicates the number of seconds RSL exceeded threshold number 2.
INT genEquipPmTrafficSLMinTsl	1.3.6.1.4.1.2281.10.6.3.2.1.1.8	INTEGER	read-only	This value indicates the Minimum TSL value.
INT genEquipPmTrafficSLMaxTsl	1.3.6.1.4.1.2281.10.6.3.2.1.1.9	INTEGER	read-only	This value indicates the Maximum TSL value.
INT genEquipPmTrafficSLTslExceed	1.3.6.1.4.1.2281.10.6.3.2.1.1.10	INTEGER	read-only	This value indicates the number of seconds TSL exceeded the threshold
NUM genEquipPmTrafficSLIDF	1.3.6.1.4.1.2281.10.6.3.2.1.1.11	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmTrafficAggregate	1.3.6.1.4.1.2281.10.6.3.3
genEquipPmTrafficAggTable	1.3.6.1.4.1.2281.10.6.3.3.1		not-accessible	This table indicates the Radio Aggregate PM data.
genEquipPmTrafficAggEntry	1.3.6.1.4.1.2281.10.6.3.3.1.1		not-accessible	This table indicates the Radio Aggregate PM data.
PMT genEquipPmTrafficAggPmType	1.3.6.1.4.1.2281.10.6.3.3.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmTrafficAggInterval	1.3.6.1.4.1.2281.10.6.3.3.1.1.2	INTEGER	read-only	This value indicates an index of a specific PM Interval
INT genEquipPmTrafficAggES	1.3.6.1.4.1.2281.10.6.3.3.1.1.3	INTEGER	read-only	This value indicates the ES value (Errored seconds).
INT genEquipPmTrafficAggSES	1.3.6.1.4.1.2281.10.6.3.3.1.1.4	INTEGER	read-only	This value indicates the SES value (Severe Errored seconds).
INT genEquipPmTrafficAggUAS	1.3.6.1.4.1.2281.10.6.3.3.1.1.5	INTEGER	read-only	This value indicates the UAS value. (Unavailable Seconds)
INT genEquipPmTrafficAggBBE	1.3.6.1.4.1.2281.10.6.3.3.1.1.6	INTEGER	read-only	This value indicates the BBE value. (Background Block Error)
NUM genEquipPmTrafficAggIDF	1.3.6.1.4.1.2281.10.6.3.3.1.1.7	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmRadio	1.3.6.1.4.1.2281.10.6.3.4
genEquipPmRadioMRMC	1.3.6.1.4.1.2281.10.6.3.4.1
genEquipPmRadioMRMCTable	1.3.6.1.4.1.2281.10.6.3.4.1.1		not-accessible	The MRMC PM table
genEquipPmRadioMRMCEntry	1.3.6.1.4.1.2281.10.6.3.4.1.1.1		not-accessible	The MRMC PM table
PMT genEquipPmRadioMRMCPmType	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
OID genEquipPmRadioMRMCId	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.2	RadioId	read-only	This value indicates an index of a specific RFU
INT genEquipPmRadioMRMCInterval	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.3	INTEGER	read-only	This value indicates an index of a specific PM Interval
INT genEquipPmRadioMRMCIfIndex	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.4	INTEGER	read-only	This value indicates the interface index of a specific RFU interface (as appears in the ifTable)
INT genEquipPmRadioMRMCMinProfile	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.5	INTEGER	read-only	Minimum MRMC profile.
INT genEquipPmRadioMRMCMaxProfile	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.6	INTEGER	read-only	The maximum profile (Kbps) that was measured during the interva
INT genEquipPmRadioMRMCMinBitrate	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.7	INTEGER	read-only	Minimum MRMC nominal bitrate (Units are Kbps)
INT genEquipPmRadioMRMCMaxBitrate	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.8	INTEGER	read-only	Maximum MRMC nominal bitrate (Units are Kbps)
INT genEquipPmRadioMRMCMinTDMIf	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.9	INTEGER	read-only	Minimum number of allocated TDM channels
INT genEquipPmRadioMRMCMaxTDMIf	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.10	INTEGER	read-only	Maximum number of allocated TDM channels
NUM genEquipPmRadioMRMCIDF	1.3.6.1.4.1.2281.10.6.3.4.1.1.1.11	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmRadioTDM	1.3.6.1.4.1.2281.10.6.3.4.2
genEquipPmRadioTDMTable	1.3.6.1.4.1.2281.10.6.3.4.2.1		not-accessible	The PM table of logical TDM channels within the Radio link
genEquipPmRadioTDMEntry	1.3.6.1.4.1.2281.10.6.3.4.2.1.1		not-accessible	The PM table of logical TDM channels within the Radio link
PMT genEquipPmRadioTDMPmType	1.3.6.1.4.1.2281.10.6.3.4.2.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmRadioTDMInterval	1.3.6.1.4.1.2281.10.6.3.4.2.1.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmRadioTDMRadioUAS	1.3.6.1.4.1.2281.10.6.3.4.2.1.1.3	INTEGER	read-only	TDM channel UAS (unavailable seconds)
NUM genEquipPmRadioTDMIDF	1.3.6.1.4.1.2281.10.6.3.4.2.1.1.4	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmRadioEthernet	1.3.6.1.4.1.2281.10.6.3.4.3
genEquipPmRadioEthernetTable	1.3.6.1.4.1.2281.10.6.3.4.3.1		not-accessible	The Ethernet PMs on the radio link
genEquipPmRadioEthernetEntry	1.3.6.1.4.1.2281.10.6.3.4.3.1.1		not-accessible	The Ethernet PMs on the radio link
PMT genEquipPmRadioEthernetPmType	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmRadioEthernetInterval	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmRadioEthernetFrameErrorRate	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.3	INTEGER	read-only	Ethernet Frame Error Rate PM
INT genEquipPmRadioEthernetPeakThroughput	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.4	INTEGER	read-only	Ethernet Peak throughput PM (Units are bits per second)
INT genEquipPmRadioEthernetAverageThroughput	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.5	INTEGER	read-only	Ethernet Average throughput PM (Units are bits per second)
INT genEquipPmRadioEthernetExceedThroughput	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.6	INTEGER	read-only	Ethernet Exceed throughput PM
INT genEquipPmRadioEthernetPeakCapacity	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.7	INTEGER	read-only	Ethernet Peak capacity PM (in bps)
INT genEquipPmRadioEthernetAverageCapacity	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.8	INTEGER	read-only	Ethernet Average capacity PM (in bps)
INT genEquipPmRadioEthernetExceedCapacity	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.9	INTEGER	read-only	Ethernet Exceed capacity PM
INT genEquipPmRadioEthernetPeakUtilization	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.10	INTEGER	read-only	Ethernet Peak utilization PM (%)
INT genEquipPmRadioEthernetAverageUtilization	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.11	INTEGER	read-only	Ethernet Average utilization PM (%)
INT genEquipPmRadioEthernetExceedUtilization	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.12	INTEGER	read-only	Ethernet Exceed utilization PM
NUM genEquipPmRadioEthernetIDF	1.3.6.1.4.1.2281.10.6.3.4.3.1.1.13	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmRadioEthernetThresholdTable	1.3.6.1.4.1.2281.10.6.3.4.3.2		not-accessible	The Ethernet PMs on the radio link
genEquipPmRadioEthernetThresholdEntry	1.3.6.1.4.1.2281.10.6.3.4.3.2.1		not-accessible	The Ethernet PMs on the radio link
INT genEquipPmRadioEthernetThresholdThroughput	1.3.6.1.4.1.2281.10.6.3.4.3.2.1.1	INTEGER	read-write	Ethernet Throughput threshold (in Mbps)
INT genEquipPmRadioEthernetThresholdCapacity	1.3.6.1.4.1.2281.10.6.3.4.3.2.1.2	INTEGER	read-write	Ethernet capacity threshold (in Mbps)
INT genEquipPmRadioEthernetThresholdUtilization	1.3.6.1.4.1.2281.10.6.3.4.3.2.1.3	INTEGER	read-write	Ethernet utilization threshold (in percentage).
genEquipPmRadioEthernetEtmTable	1.3.6.1.4.1.2281.10.6.3.4.3.3		not-accessible	The Ethernet PMs on the radio link
genEquipPmRadioEthernetEtmEntry	1.3.6.1.4.1.2281.10.6.3.4.3.3.1		not-accessible	The entry of Ethernet ETM PMs on the radio link
PMT genEquipPmRadioEthernetEtmPmType	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmRadioEthernetEtmPmQueueIndex	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.2	INTEGER	read-only	Queue index
INT genEquipPmRadioEthernetEtmInterval	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.3	INTEGER	read-only	The interval of the PM.
INT genEquipPmRadioEthernetEtmPmMaxGreenBytesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.4	INTEGER	read-only	Maximum Green Traffic Passed Bytes.
INT genEquipPmRadioEthernetEtmPmAvgGreenBytesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.5	INTEGER	read-only	Average Green Traffic Passed Bytes.
INT genEquipPmRadioEthernetEtmPmMaxGreenFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.6	INTEGER	read-only	Maximum Green Traffic Frames Droped by WRED.
INT genEquipPmRadioEthernetEtmPmAvgGreenFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.7	INTEGER	read-only	Average Green Traffic Frames Droped by WRED.
INT genEquipPmRadioEthernetEtmPmMaxYellowBytesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.8	INTEGER	read-only	Maximum Yellow Traffic Passed Bytes.
INT genEquipPmRadioEthernetEtmPmAvgYellowBytesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.9	INTEGER	read-only	Average Yellow Traffic Passed Bytes.
INT genEquipPmRadioEthernetEtmPmMaxYellowFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.10	INTEGER	read-only	Maximum Yellow Traffic Frames Droped by WRED.
INT genEquipPmRadioEthernetEtmPmAvgYellowFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.11	INTEGER	read-only	Average Yellow Traffic Frames Droped by WRED.
INT genEquipPmRadioEthernetEtmPmMaxRedFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.12	INTEGER	read-only	Maximum Red Traffic Frames Dropped.
INT genEquipPmRadioEthernetEtmPmAvgRedFramesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.13	INTEGER	read-only	Average Red Traffic Frames Dropped.
NUM genEquipPmRadioEthernetEtmPmIDF	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.14	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
INT genEquipPmRadioEthernetEtmPmMaxGreenFramesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.17	INTEGER	read-only	Maximum Green Traffic Frames Passed.
INT genEquipPmRadioEthernetEtmPmAvgGreenFramesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.18	INTEGER	read-only	Average Green Traffic Frames Passed.
INT genEquipPmRadioEthernetEtmPmMaxYellowFramesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.21	INTEGER	read-only	Maximum Yellow Traffic Frames Passed.
INT genEquipPmRadioEthernetEtmPmAvgYellowFramesPassed	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.22	INTEGER	read-only	Average Yellow Traffic Frames Passed.
INT genEquipPmRadioEthernetEtmPmMaxRedBytesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.23	INTEGER	read-only	Maximum Red Traffic Bytes Dropped.
INT genEquipPmRadioEthernetEtmPmAvgRedBytesDropped	1.3.6.1.4.1.2281.10.6.3.4.3.3.1.24	INTEGER	read-only	Average Red Traffic Bytes Dropped.
genEquipPmRadioMSETable	1.3.6.1.4.1.2281.10.6.3.4.4		not-accessible	Radio MSE PM
genEquipPmRadioMSEEntry	1.3.6.1.4.1.2281.10.6.3.4.4.1		not-accessible	Radio MSE PM
PMT genEquipPmRadioMSEPmType	1.3.6.1.4.1.2281.10.6.3.4.4.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmRadioMSEInterval	1.3.6.1.4.1.2281.10.6.3.4.4.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmRadioMSEMinMse	1.3.6.1.4.1.2281.10.6.3.4.4.1.3	INTEGER	read-only	This parameter holds the minimum MSE value detected in the interval.
INT genEquipPmRadioMSEMaxMse	1.3.6.1.4.1.2281.10.6.3.4.4.1.4	INTEGER	read-only	This parameter holds the maximum MSE value detected in the interval.
INT genEquipPmRadioMSEexceeded	1.3.6.1.4.1.2281.10.6.3.4.4.1.5	INTEGER	read-only	This parameter holds the number of seconds that the MSE exceeded the configured threshold.
NUM genEquipPmRadioMSEIDF	1.3.6.1.4.1.2281.10.6.3.4.4.1.6	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmRadioThresholdTable	1.3.6.1.4.1.2281.10.6.3.4.5		not-accessible	Radio MSE PM
genEquipPmRadioThresholdEntry	1.3.6.1.4.1.2281.10.6.3.4.5.1		not-accessible	Radio MSE PM
INT genEquipPmRadioThresholdMSE	1.3.6.1.4.1.2281.10.6.3.4.5.1.1	INTEGER	read-write	The threshold above which MSE (Mean Square Error) exceeded seconds will be counted
INT genEquipPmRadioThresholdRSL1	1.3.6.1.4.1.2281.10.6.3.4.5.1.2	INTEGER	read-write	The threshold below which RSL 1 exceeded seconds will be counted
INT genEquipPmRadioThresholdRSL2	1.3.6.1.4.1.2281.10.6.3.4.5.1.3	INTEGER	read-write	The threshold below which RSL 2 exceeded seconds will be counted
INT genEquipPmRadioThresholdTSL	1.3.6.1.4.1.2281.10.6.3.4.5.1.4	INTEGER	read-write	The threshold above which TSL exceeded seconds will be counted
INT genEquipPmRadioThresholdXPI	1.3.6.1.4.1.2281.10.6.3.4.5.1.5	INTEGER	read-write	The threshold above which XPI (Cross Polar Interference) exceeded seconds will be counted
genEquipPmRadioXPITable	1.3.6.1.4.1.2281.10.6.3.4.6		not-accessible	Radio XPIC PM
genEquipPmRadioXPIEntry	1.3.6.1.4.1.2281.10.6.3.4.6.1		not-accessible	Radio XPIC PM
PMT genEquipPmRadioXPIPmType	1.3.6.1.4.1.2281.10.6.3.4.6.1.1	PmTableType	read-only	The interval of the PM
INT genEquipPmRadioXPIPmInterval	1.3.6.1.4.1.2281.10.6.3.4.6.1.2	INTEGER	read-only	The number of the interval: 1-30 in case the interval is 24 hours or 1-900 in case the interval is 15 minutes
INT genEquipPmRadioXPIPmMinXPI	1.3.6.1.4.1.2281.10.6.3.4.6.1.3	INTEGER	read-only	This parameter holds the minimum XPI value detected in the interval
INT genEquipPmRadioXPIPmMaxXPI	1.3.6.1.4.1.2281.10.6.3.4.6.1.4	INTEGER	read-only	This parameter holds the maximum XPI value detected in the interval
INT genEquipPmRadioXPIBelowThreshold	1.3.6.1.4.1.2281.10.6.3.4.6.1.5	INTEGER	read-only	This parameter holds the number of seconds in the interval that the XPI value was below the configured threshold.
NUM genEquipPmRadioXPIIDF	1.3.6.1.4.1.2281.10.6.3.4.6.1.6	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
OFF genEquipPmRadioClear	1.3.6.1.4.1.2281.10.6.3.4.7	OffOn	read-write	Clear all radio PMs (Performance Monitoring).
genEquipPmTDM	1.3.6.1.4.1.2281.10.6.3.5
genEquipPmTdmTable	1.3.6.1.4.1.2281.10.6.3.5.1		not-accessible	The line TDM PM table
genEquipPmTdmEntry	1.3.6.1.4.1.2281.10.6.3.5.1.1		not-accessible	The line TDM PM table
PMT genEquipPmTdmPmType	1.3.6.1.4.1.2281.10.6.3.5.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmTdmInterval	1.3.6.1.4.1.2281.10.6.3.5.1.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmTdmES	1.3.6.1.4.1.2281.10.6.3.5.1.1.3	INTEGER	read-only	ES PM (Errored second)
INT genEquipPmTdmSES	1.3.6.1.4.1.2281.10.6.3.5.1.1.4	INTEGER	read-only	SES PM (Severe Errored Seconds)
INT genEquipPmTdmUAS	1.3.6.1.4.1.2281.10.6.3.5.1.1.5	INTEGER	read-only	UAS PM (Unavailable Seconds).
INT genEquipPmTdmBBE	1.3.6.1.4.1.2281.10.6.3.5.1.1.6	INTEGER	read-only	BBE PM (Background Block Errors)
NUM genEquipPmTdmIDF	1.3.6.1.4.1.2281.10.6.3.5.1.1.7	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmSDH	1.3.6.1.4.1.2281.10.6.3.6
genEquipPmSdhTable	1.3.6.1.4.1.2281.10.6.3.6.1		not-accessible	The line SDH PM table.
genEquipPmSdhEntry	1.3.6.1.4.1.2281.10.6.3.6.1.1		not-accessible	The line SDH PM table.
PMT genEquipPmSdhPmType	1.3.6.1.4.1.2281.10.6.3.6.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
INT genEquipPmSdhInterval	1.3.6.1.4.1.2281.10.6.3.6.1.1.2	INTEGER	read-only	The interval of the PM.
INT genEquipPmSdhES	1.3.6.1.4.1.2281.10.6.3.6.1.1.3	INTEGER	read-only	ES STM-1/OC-3 PM.
INT genEquipPmSdhSES	1.3.6.1.4.1.2281.10.6.3.6.1.1.4	INTEGER	read-only	SES STM-1/OC-3 PM.
INT genEquipPmSdhEB	1.3.6.1.4.1.2281.10.6.3.6.1.1.5	INTEGER	read-only	EB STM-1/OC-3 PM (Errored block).
INT genEquipPmSdhBBE	1.3.6.1.4.1.2281.10.6.3.6.1.1.6	INTEGER	read-only	BBE PM (background errored block STM-1/OC-3 PM or CVL PM (code violation line) when using OC-3.
NUM genEquipPmSdhIDF	1.3.6.1.4.1.2281.10.6.3.6.1.1.7	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
INT genEquipPmSdhIfIndex	1.3.6.1.4.1.2281.10.6.3.6.1.1.8	INTEGER	read-only	Port Number.
INT genEquipPmSdhTimeStamp	1.3.6.1.4.1.2281.10.6.3.6.1.1.9	INTEGER	read-only	This value indicates the time stamp of the interval.
INT genEquipPmSdhUAS	1.3.6.1.4.1.2281.10.6.3.6.1.1.10	INTEGER	read-only	Un-Available Seconds STM-1/OC-3 PM.
genEquipPmSdhRstLRTable	1.3.6.1.4.1.2281.10.6.3.6.2		not-accessible	SONET/STM-1 interface-level PMs for line to radio direction.
genEquipPmSdhRstLREntry	1.3.6.1.4.1.2281.10.6.3.6.2.1		not-accessible	SONET/STM-1 interface-level PMs for line to radio direction entry.
PMT genEquipPmSdhRstLRPmType	1.3.6.1.4.1.2281.10.6.3.6.2.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
INT genEquipPmSdhRstLRIfIndex	1.3.6.1.4.1.2281.10.6.3.6.2.1.2	INTEGER	read-only	Port number.
INT genEquipPmSdhRstLRInterval	1.3.6.1.4.1.2281.10.6.3.6.2.1.3	INTEGER	read-only	The interval of the PM.
INT genEquipPmSdhRstLRTimeStamp	1.3.6.1.4.1.2281.10.6.3.6.2.1.4	INTEGER	read-only	This value indicates the time stamp of the interval.
INT genEquipPmSdhRstLRES	1.3.6.1.4.1.2281.10.6.3.6.2.1.5	INTEGER	read-only	Errored Seconds PM for STM-1/OC-3 on line to radio direction.
INT genEquipPmSdhRstLRSES	1.3.6.1.4.1.2281.10.6.3.6.2.1.6	INTEGER	read-only	Severely Errored Seconds PM for STM-1/OC-3 on line to radio direction.
INT genEquipPmSdhRstLRUAS	1.3.6.1.4.1.2281.10.6.3.6.2.1.7	INTEGER	read-only	Unavailable Seconds PM for STM-1/OC-3.
INT genEquipPmSdhRstLREB	1.3.6.1.4.1.2281.10.6.3.6.2.1.8	INTEGER	read-only	Errored Blocks PM for STM-1/OC-3 on line to radio direction.
INT genEquipPmSdhRstLRCV	1.3.6.1.4.1.2281.10.6.3.6.2.1.9	INTEGER	read-only	Code Viloations PM for STM-1/OC-3 on line to radio direction.
INT genEquipPmSdhRstLRBBE	1.3.6.1.4.1.2281.10.6.3.6.2.1.10	INTEGER	read-only	Background Block Error PM for STM-1/OC-3 on line to radio direction.
NUM genEquipPmSdhRstLRIDF	1.3.6.1.4.1.2281.10.6.3.6.2.1.11	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmSdhRstRLTable	1.3.6.1.4.1.2281.10.6.3.6.3		not-accessible	SONET/STM-1 interface-level PMs for radio to line direction.
genEquipPmSdhRstRLEntry	1.3.6.1.4.1.2281.10.6.3.6.3.1		not-accessible	SONET/STM-1 interface-level PMs for radio to line direction entry.
PMT genEquipPmSdhRstRLPmType	1.3.6.1.4.1.2281.10.6.3.6.3.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
INT genEquipPmSdhRstRLIfIndex	1.3.6.1.4.1.2281.10.6.3.6.3.1.2	INTEGER	read-only	Port number.
INT genEquipPmSdhRstRLInterval	1.3.6.1.4.1.2281.10.6.3.6.3.1.3	INTEGER	read-only	The interval of the PM.
INT genEquipPmSdhRstRLTimeStamp	1.3.6.1.4.1.2281.10.6.3.6.3.1.4	INTEGER	read-only	This value indicates the time stamp of the interval.
INT genEquipPmSdhRstRLES	1.3.6.1.4.1.2281.10.6.3.6.3.1.5	INTEGER	read-only	Errored Seconds PM for STM-1/OC-3 on radio to line direction.
INT genEquipPmSdhRstRLSES	1.3.6.1.4.1.2281.10.6.3.6.3.1.6	INTEGER	read-only	Severely Errored Seconds PM for STM-1/OC-3 on radio to line direction.
INT genEquipPmSdhRstRLUAS	1.3.6.1.4.1.2281.10.6.3.6.3.1.7	INTEGER	read-only	Unavailable Seconds PM for STM-1/OC-3.
INT genEquipPmSdhRstRLEB	1.3.6.1.4.1.2281.10.6.3.6.3.1.8	INTEGER	read-only	Errored Blocks PM for STM-1/OC-3 on radio to line direction.
INT genEquipPmSdhRstRLCV	1.3.6.1.4.1.2281.10.6.3.6.3.1.9	INTEGER	read-only	Code Viloations PM for STM-1/OC-3 on radio to line direction.
INT genEquipPmSdhRstRLBBE	1.3.6.1.4.1.2281.10.6.3.6.3.1.10	INTEGER	read-only	Background Block Error PM for STM-1/OC-3 on radio to line direction.
NUM genEquipPmSdhRstRLIDF	1.3.6.1.4.1.2281.10.6.3.6.3.1.11	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmTrails	1.3.6.1.4.1.2281.10.6.3.7
genEquipPmTrailsEndPointTable	1.3.6.1.4.1.2281.10.6.3.7.1		not-accessible	PM table of the E1/T1 trails.
genEquipPmTrailsEndPointEntry	1.3.6.1.4.1.2281.10.6.3.7.1.1		not-accessible	PM table of the E1/T1 trails.
PMT genEquipPmTrailsEndPointPmType	1.3.6.1.4.1.2281.10.6.3.7.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
STR genEquipPmTrailsEndPointId	1.3.6.1.4.1.2281.10.6.3.7.1.1.2	DisplayString	read-only	This value indicates the trail id.
INT genEquipPmTrailsEndPointEPId	1.3.6.1.4.1.2281.10.6.3.7.1.1.3	INTEGER	read-only	This value indicates the end point number for this trail. If the trail is protected, there will be two end points for the trail (primary path and the secondary path).
INT genEquipPmTrailsEndPointInterval	1.3.6.1.4.1.2281.10.6.3.7.1.1.4	INTEGER	read-only	The interval of the PM.
INT genEquipPmTrailsEndPointES	1.3.6.1.4.1.2281.10.6.3.7.1.1.5	INTEGER	read-only	ES PM (Errored Seconds).
INT genEquipPmTrailsEndPointSES	1.3.6.1.4.1.2281.10.6.3.7.1.1.6	INTEGER	read-only	SES PM (Severe Errored Seconds).
INT genEquipPmTrailsEndPointUAS	1.3.6.1.4.1.2281.10.6.3.7.1.1.7	INTEGER	read-only	UAS PM (Unavailable Seconds).
INT genEquipPmTrailsEndPointBBE	1.3.6.1.4.1.2281.10.6.3.7.1.1.8	INTEGER	read-only	BBE PM (Background Block Errors).
INT genEquipPmTrailsEndPointNoOfSwitches	1.3.6.1.4.1.2281.10.6.3.7.1.1.9	INTEGER	read-only	A counter of the number of SNCP switches (between primary and secondary paths) that trail had in the relevant interval.
INT genEquipPmTrailsEndPointActivePathCounts	1.3.6.1.4.1.2281.10.6.3.7.1.1.10	INTEGER	read-only	Active path seconds.
NUM genEquipPmTrailsEndPointIDF	1.3.6.1.4.1.2281.10.6.3.7.1.1.11	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmPW	1.3.6.1.4.1.2281.10.6.3.8
genEquipPmPWTable	1.3.6.1.4.1.2281.10.6.3.8.1		not-accessible	This table shows standard pseudowire-level PM measurements. Notice that PMs at the TDM port level are maintained separately.
genEquipPmPWEntry	1.3.6.1.4.1.2281.10.6.3.8.1.1		not-accessible	This table shows standard pseudowire-level PM measurements. Notice that PMs at the TDM port level are maintained separately.
PMT genEquipPmPWPmType	1.3.6.1.4.1.2281.10.6.3.8.1.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
INT genEquipPmPWId	1.3.6.1.4.1.2281.10.6.3.8.1.1.2	INTEGER	read-only	This value indicates the trail id.
INT genEquipPmPWInterval	1.3.6.1.4.1.2281.10.6.3.8.1.1.3	INTEGER	read-only	The interval of the PM.
INT genEquipPmPWMissingPkts	1.3.6.1.4.1.2281.10.6.3.8.1.1.4	INTEGER	read-only	Number of missing packets (as detected via control word sequence number gaps).
INT genEquipPmPWPktsReOrder	1.3.6.1.4.1.2281.10.6.3.8.1.1.5	INTEGER	read-only	Number of packets detected out of sequence (via control word sequence number) but successfully re-ordered.
INT genEquipPmPWtrBfrUnderruns	1.3.6.1.4.1.2281.10.6.3.8.1.1.6	INTEGER	read-only	Number of times a packet needed to be played out and the jitter buffer was empty.
INT genEquipPmPWMisOrderDropped	1.3.6.1.4.1.2281.10.6.3.8.1.1.7	INTEGER	read-only	Number of packets detected out of order (via control word sequence numbers) that could not be re-ordered or could not fit in the jitter buffer.
INT genEquipPmPWMalformedPkt	1.3.6.1.4.1.2281.10.6.3.8.1.1.8	INTEGER	read-only	Number of packets detected with unexpected size, or bad headers' stack.
INT genEquipPmPWES	1.3.6.1.4.1.2281.10.6.3.8.1.1.9	INTEGER	read-only	ES PM (Errored Seconds).
INT genEquipPmPWSES	1.3.6.1.4.1.2281.10.6.3.8.1.1.10	INTEGER	read-only	SES PM (Severe Errored Seconds).
INT genEquipPmPWUAS	1.3.6.1.4.1.2281.10.6.3.8.1.1.11	INTEGER	read-only	UAS PM (Unavailable Seconds).
INT genEquipPmPWFC	1.3.6.1.4.1.2281.10.6.3.8.1.1.12	INTEGER	read-only	FC (Failure Counts) PM. A failure is a LOPS event.
NUM genEquipPmPWIDF	1.3.6.1.4.1.2281.10.6.3.8.1.1.13	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmNGPWTable	1.3.6.1.4.1.2281.10.6.3.8.2		not-accessible	This table contains PW Performance Monitoring counters.
genEquipPmNGPWEntry	1.3.6.1.4.1.2281.10.6.3.8.2.1		not-accessible	This table entry contains PW Performance Monitoring counters.
PMT genEquipPmNGPWPmType	1.3.6.1.4.1.2281.10.6.3.8.2.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours.
INT genEquipPmNGPWIfIndex	1.3.6.1.4.1.2281.10.6.3.8.2.1.2	INTEGER	read-only	This value indicates the interface Index.
INT genEquipPmNGPWInterval	1.3.6.1.4.1.2281.10.6.3.8.2.1.3	INTEGER	read-only	The interval of the PM.
INT genEquipPmNGPWES	1.3.6.1.4.1.2281.10.6.3.8.2.1.4	INTEGER	read-only	ES (Errored Seconds) PM.
INT genEquipPmNGPWSES	1.3.6.1.4.1.2281.10.6.3.8.2.1.5	INTEGER	read-only	SES (Severe Errored Seconds) PM.
INT genEquipPmNGPWUAS	1.3.6.1.4.1.2281.10.6.3.8.2.1.6	INTEGER	read-only	UAS (Unavailable Seconds) PM.
INT genEquipPmNGPWFC	1.3.6.1.4.1.2281.10.6.3.8.2.1.7	INTEGER	read-only	FC (Failure Counts) PM. A failure is a LOPS event.
INT genEquipPmNGPWFER	1.3.6.1.4.1.2281.10.6.3.8.2.1.8	INTEGER	read-only	Frame Error Ratio.
INT genEquipPmNGPWMissingPkts	1.3.6.1.4.1.2281.10.6.3.8.2.1.9	INTEGER	read-only	Number of missing packets (as detected via control word sequence number gaps).
INT genEquipPmNGPWPktsReOrder	1.3.6.1.4.1.2281.10.6.3.8.2.1.10	INTEGER	read-only	Number of packets detected out of sequence (via control word sequence number) but successfully re-ordered.
INT genEquipPmNGPWMisOrderDropped	1.3.6.1.4.1.2281.10.6.3.8.2.1.11	INTEGER	read-only	Number of packets detected out of order (via control word sequence numbers) that could not be re-ordered or could not fit in the jitter buffer.
INT genEquipPmNGPWMalformedPkt	1.3.6.1.4.1.2281.10.6.3.8.2.1.12	INTEGER	read-only	Number of packets detected with unexpected size, or bad headers' stack.
NUM genEquipPmNGPWIdf	1.3.6.1.4.1.2281.10.6.3.8.2.1.13	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmEthUtilization	1.3.6.1.4.1.2281.10.6.3.9
ENA genEquipPmEthUtilizationAdmin	1.3.6.1.4.1.2281.10.6.3.9.1	EnableDisable	read-write	Ethernet port utilization PM admin
INT genEquipPmEthUtilizationThreshold	1.3.6.1.4.1.2281.10.6.3.9.2	INTEGER	read-write	User defined threshold for Ethernet port utilization PM.
genEquipPmEthUtilizationTable	1.3.6.1.4.1.2281.10.6.3.9.3		not-accessible	The Ethernet ports Utilization PMs
genEquipPmEthUtilizationEntry	1.3.6.1.4.1.2281.10.6.3.9.3.1		not-accessible	The Ethernet ports Utilization PMs
PMT genEquipPmEthUtilizationPmType	1.3.6.1.4.1.2281.10.6.3.9.3.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmEthUtilizationInterval	1.3.6.1.4.1.2281.10.6.3.9.3.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmEthUtilizationPeakUtilization	1.3.6.1.4.1.2281.10.6.3.9.3.1.3	INTEGER	read-only	Peak Ethernet port utilization of the current interval.
INT genEquipPmEthUtilizationAverageUtilization	1.3.6.1.4.1.2281.10.6.3.9.3.1.4	INTEGER	read-only	Average Ethernet port utilization of the current interval.
INT genEquipPmEthUtilizationExceedUtilization	1.3.6.1.4.1.2281.10.6.3.9.3.1.5	INTEGER	read-only	Number of seconds in current interval when Ethernet port utilization exceeded the user defined threshold.
NUM genEquipPmEthUtilizationIDF	1.3.6.1.4.1.2281.10.6.3.9.3.1.6	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmEthernetIngressPolicer	1.3.6.1.4.1.2281.10.6.3.10
genEquipPmEthernetIngressPolicerUnicastStatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.1		not-accessible	logical Interface unicast policer statistics.
genEquipPmEthernetIngressPolicerUnicastStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.1.1		not-accessible	logical Interface unicast policer statistics.
INT genEquipPmEthernetIngressPolicerUnicastStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.1.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerUnicastStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.1.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.1.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.1.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.1.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.1.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.1.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerUnicastStatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.1.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetIngressPolicerMulticastStatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.2		not-accessible	Logical Port multicast policer statistics.
genEquipPmEthernetIngressPolicerMulticastStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.2.1		not-accessible	Logical Port multicast policer statistics.
INT genEquipPmEthernetIngressPolicerMulticastStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.2.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerMulticastStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.2.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.2.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.2.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.2.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.2.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.2.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerMulticastStatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.2.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetIngressPolicerBroadcastStatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.3		not-accessible	Interface Logical Port broadcast policer statistics.
genEquipPmEthernetIngressPolicerBroadcastStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.3.1		not-accessible	Interface Logical Port broadcast policer statistics.
INT genEquipPmEthernetIngressPolicerBroadcastStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.3.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerBroadcastStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.3.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.3.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.3.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.3.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.3.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.3.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerBroadcastStatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.3.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetIngressPolicerEtherType1StatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.4		not-accessible	Interface Logical Port ether Type 1 policer statistics.
genEquipPmEthernetIngressPolicerEtherType1StatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.4.1		not-accessible	Interface Logical Port ether Type 1 policer statistics.
INT genEquipPmEthernetIngressPolicerEtherType1StatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.4.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerEtherType1StatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.4.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.4.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.4.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.4.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.4.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.4.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerEtherType1StatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.4.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetIngressPolicerEtherType2StatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.5		not-accessible	Interface Logical Port ether Type 2 policer statistics.
genEquipPmEthernetIngressPolicerEtherType2StatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.5.1		not-accessible	Interface Logical Port ether Type 2 policer statistics.
INT genEquipPmEthernetIngressPolicerEtherType2StatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.5.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerEtherType2StatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.5.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.5.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.5.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.5.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.5.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.5.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerEtherType2StatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.5.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetIngressPolicerEtherType3StatisticsTable	1.3.6.1.4.1.2281.10.6.3.10.6		not-accessible	Interface Logical Port ether Type 3 policer statistics.
genEquipPmEthernetIngressPolicerEtherType3StatisticsEntry	1.3.6.1.4.1.2281.10.6.3.10.6.1		not-accessible	Interface Logical Port ether Type 3 policer statistics.
INT genEquipPmEthernetIngressPolicerEtherType3StatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.10.6.1.1	INTEGER	read-only	Ethernet Logical port if-index table key
NOY genEquipPmEthernetIngressPolicerEtherType3StatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.10.6.1.2	NoYes	read-write	Clear counter statistics after reading.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsGreenPacket	1.3.6.1.4.1.2281.10.6.3.10.6.1.3	Counter64	read-only	The number of packets that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsGreenBytes	1.3.6.1.4.1.2281.10.6.3.10.6.1.4	Counter64	read-only	The number of bytes that were counted as green.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsYellowPacket	1.3.6.1.4.1.2281.10.6.3.10.6.1.5	Counter64	read-only	The number of packets that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsYellowBytes	1.3.6.1.4.1.2281.10.6.3.10.6.1.6	Counter64	read-only	The number of bytes that were counted as yellow.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsRedPacket	1.3.6.1.4.1.2281.10.6.3.10.6.1.7	Counter64	read-only	The number of packets that were counted as red.
C64 genEquipPmEthernetIngressPolicerEtherType3StatisticsRedBytes	1.3.6.1.4.1.2281.10.6.3.10.6.1.8	Counter64	read-only	The number of bytes that were counted as red.
genEquipPmEthernetRmonStatisticsTable	1.3.6.1.4.1.2281.10.6.3.11		not-accessible	Interface physical Port RMON statistics.
genEquipPmEthernetRmonStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.11.1		not-accessible	Interface physical Port RMON statistics.
INT genEquipPmEthernetRmonStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.11.1.1	INTEGER	read-only	Ethernet Physical port if-index table key
NOY genEquipPmEthernetRmonStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.11.1.2	NoYes	read-write	Clear on read
C64 genEquipPmEthernetRmonStatisticsTxByteCount	1.3.6.1.4.1.2281.10.6.3.11.1.3	Counter64	read-only	TX byte count
CTR genEquipPmEthernetRmonStatisticsTxFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.4	Counter	read-only	TX frame count
CTR genEquipPmEthernetRmonStatisticsTxMulticastFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.5	Counter	read-only	TX multicast frame count
CTR genEquipPmEthernetRmonStatisticsTxBroadcastFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.6	Counter	read-only	TX broadcast frame count
CTR genEquipPmEthernetRmonStatisticsTxControlFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.7	Counter	read-only	TX control frame count
CTR genEquipPmEthernetRmonStatisticsTxPauseFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.8	Counter	read-only	TX pause frame count
CTR genEquipPmEthernetRmonStatisticsTxFcsErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.9	Counter	read-only	TX fcs error frame count
CTR genEquipPmEthernetRmonStatisticsTxLengthErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.10	Counter	read-only	TX length error frame count
CTR genEquipPmEthernetRmonStatisticsTxOversizeFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.11	Counter	read-only	TX oversize frame count
CTR genEquipPmEthernetRmonStatisticsTxUndersizeFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.12	Counter	read-only	TX undersize frame count
CTR genEquipPmEthernetRmonStatisticsTxFragmentFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.13	Counter	read-only	TX fragment frame count
CTR genEquipPmEthernetRmonStatisticsTxJabberFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.14	Counter	read-only	TX jabber frame count
CTR genEquipPmEthernetRmonStatisticsTx64FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.15	Counter	read-only	TX 64 frame count
CTR genEquipPmEthernetRmonStatisticsTx65_127FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.16	Counter	read-only	TX 65-127 frame count
CTR genEquipPmEthernetRmonStatisticsTx128_255FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.17	Counter	read-only	TX 128-255 frame count
CTR genEquipPmEthernetRmonStatisticsTx256_511FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.18	Counter	read-only	TX 256-511 frame count
CTR genEquipPmEthernetRmonStatisticsTx512_1023FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.19	Counter	read-only	TX 512-1023 frame count
CTR genEquipPmEthernetRmonStatisticsTx1024_1518FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.20	Counter	read-only	TX 1024-1518 frame count
CTR genEquipPmEthernetRmonStatisticsTx1519_1522FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.21	Counter	read-only	TX 1519-1522 frame count
C64 genEquipPmEthernetRmonStatisticsRxByteCount	1.3.6.1.4.1.2281.10.6.3.11.1.22	Counter64	read-only	RX byte count
CTR genEquipPmEthernetRmonStatisticsRxFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.23	Counter	read-only	RX frame count
CTR genEquipPmEthernetRmonStatisticsRxMulticastFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.24	Counter	read-only	RX multicast frame count
CTR genEquipPmEthernetRmonStatisticsRxBroadcastFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.25	Counter	read-only	RX broadcast frame count
CTR genEquipPmEthernetRmonStatisticsRxControlFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.26	Counter	read-only	RX control frame count
CTR genEquipPmEthernetRmonStatisticsRxPauseFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.27	Counter	read-only	RX pause frame count
CTR genEquipPmEthernetRmonStatisticsRxFcsErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.28	Counter	read-only	RX fcs error frame count
CTR genEquipPmEthernetRmonStatisticsRxLengthErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.29	Counter	read-only	RX length error frame count
CTR genEquipPmEthernetRmonStatisticsRxcode_ErrorCount	1.3.6.1.4.1.2281.10.6.3.11.1.30	Counter	read-only	RX code error count
CTR genEquipPmEthernetRmonStatisticsRxoversizeFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.31	Counter	read-only	RX oversize frame count
CTR genEquipPmEthernetRmonStatisticsRxundersize_ErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.32	Counter	read-only	RX undersize error frame count
CTR genEquipPmEthernetRmonStatisticsRxFragmentFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.33	Counter	read-only	RX fragment frame count
CTR genEquipPmEthernetRmonStatisticsRx64FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.35	Counter	read-only	RX 64 frame count
CTR genEquipPmEthernetRmonStatisticsRx65_127FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.36	Counter	read-only	RX 65-127 frame count
CTR genEquipPmEthernetRmonStatisticsRx128_255FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.37	Counter	read-only	RX 128-255 frame count
CTR genEquipPmEthernetRmonStatisticsRx256_511FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.38	Counter	read-only	RX 256-511 frame count
CTR genEquipPmEthernetRmonStatisticsRx512_1023FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.39	Counter	read-only	RX 512-1023 frame count
CTR genEquipPmEthernetRmonStatisticsRx1024_1518FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.40	Counter	read-only	RX 1024-1518 frame count
CTR genEquipPmEthernetRmonStatisticsRx1519_1522FrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.41	Counter	read-only	RX 1519-1522 frame count
CTR genEquipPmEthernetRmonStatisticsRxExceedmaxFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.42	Counter	read-only	RX exceed max frame count
CTR genEquipPmEthernetRmonStatisticsRxExceedMaxWithErrorFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.43	Counter	read-only	RX exceed max with error frame count
CTR genEquipPmEthernetRmonStatisticsRxJabberFrameCount	1.3.6.1.4.1.2281.10.6.3.11.1.44	Counter	read-only	RX jabber frame count - frames with length > 1518 bytes (1522 bytes for VLAN tagged frames) with errors
genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTable	1.3.6.1.4.1.2281.10.6.3.12		not-accessible	Service queues aggragation statistics.
genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.12.1		not-accessible	Service queues aggragation statistics.
INT genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.12.1.1	INTEGER	read-only	ifIndex
INT genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsServiceIndex	1.3.6.1.4.1.2281.10.6.3.12.1.2	INTEGER	read-only	Egress service bundle ID
NOY genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.12.1.3	NoYes	read-write	clear on read
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedGreenPacket	1.3.6.1.4.1.2281.10.6.3.12.1.4	Counter64	read-only	transmitted green packet
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedGreenBytes	1.3.6.1.4.1.2281.10.6.3.12.1.5	Counter64	read-only	transmitted green bytes
INT genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedGreenBitsPerSecond	1.3.6.1.4.1.2281.10.6.3.12.1.6	INTEGER	read-only	transmitted green bits per second
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsDroppedGreenPacket	1.3.6.1.4.1.2281.10.6.3.12.1.7	Counter64	read-only	dropped green packet
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsDroppedGreenBytes	1.3.6.1.4.1.2281.10.6.3.12.1.8	Counter64	read-only	dropped green bytes
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedYellowPacket	1.3.6.1.4.1.2281.10.6.3.12.1.9	Counter64	read-only	transmitted yellow packet
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedYellowBytes	1.3.6.1.4.1.2281.10.6.3.12.1.10	Counter64	read-only	transmitted yellow bytes
INT genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsTransmittedYellowBitsPerSecond	1.3.6.1.4.1.2281.10.6.3.12.1.11	INTEGER	read-only	transmitted yellow bits per second
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsDroppedYellowPacket	1.3.6.1.4.1.2281.10.6.3.12.1.12	Counter64	read-only	Tdropped yellow packet
C64 genEquipServicesCETTmPmSpEgressQueuesAggragateStatisticsDroppedYellowBytes	1.3.6.1.4.1.2281.10.6.3.12.1.13	Counter64	read-only	dropped yellow bytes
genEquipServicesCetSpPmCosIngressPolicerStatisticsTable	1.3.6.1.4.1.2281.10.6.3.13		not-accessible	Cos Service Point ingress Policer statistics.
genEquipServicesCetSpPmCosIngressPolicerStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.13.1		not-accessible	Cos Service Point ingress Policer statistics.
INT genEquipServicesCetSpPmCosIngressPolicerStatiServiceIndex	1.3.6.1.4.1.2281.10.6.3.13.1.1	INTEGER	read-only	service-index
INT genEquipServicesCetSpPmCosIngressPolicerStatiSpIndex	1.3.6.1.4.1.2281.10.6.3.13.1.2	INTEGER	read-only	sp-index
INT genEquipServicesCetSpPmCosIngressPolicerStatiCos	1.3.6.1.4.1.2281.10.6.3.13.1.3	INTEGER	read-only	cos index
NOY genEquipServicesCetSpPmCosIngressPolicerStatiClearOnRead	1.3.6.1.4.1.2281.10.6.3.13.1.4	NoYes	read-write	Clear on read
C64 genEquipServicesCetSpPmCosIngressPolicerStatiGreenPacket	1.3.6.1.4.1.2281.10.6.3.13.1.5	Counter64	read-only	green-packet
C64 genEquipServicesCetSpPmCosIngressPolicerStatiGreenBytes	1.3.6.1.4.1.2281.10.6.3.13.1.6	Counter64	read-only	green-bytes
C64 genEquipServicesCetSpPmCosIngressPolicerStatiYellowPacket	1.3.6.1.4.1.2281.10.6.3.13.1.7	Counter64	read-only	yellow-packet
C64 genEquipServicesCetSpPmCosIngressPolicerStatiYellowBytes	1.3.6.1.4.1.2281.10.6.3.13.1.8	Counter64	read-only	yellow-bytes
C64 genEquipServicesCetSpPmCosIngressPolicerStatiRedPacket	1.3.6.1.4.1.2281.10.6.3.13.1.9	Counter64	read-only	red-packet
C64 genEquipServicesCetSpPmCosIngressPolicerStatiRedBytes	1.3.6.1.4.1.2281.10.6.3.13.1.10	Counter64	read-only	red-bytes
genEquipServicesCetSpPmIngressPolicerStatisticsTable	1.3.6.1.4.1.2281.10.6.3.14		not-accessible	Service Point ingress Policer statistics.
genEquipServicesCetSpPmIngressPolicerStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.14.1		not-accessible	Service Point ingress Policer statistics.
INT genEquipServicesCetSpPmIngressPolicerStatiServiceIndex	1.3.6.1.4.1.2281.10.6.3.14.1.1	INTEGER	read-only	service-index
INT genEquipServicesCetSpPmIngressPolicerStatiSpIndex	1.3.6.1.4.1.2281.10.6.3.14.1.2	INTEGER	read-only	sp-index
NOY genEquipServicesCetSpPmIngressPolicerStatiClearOnRead	1.3.6.1.4.1.2281.10.6.3.14.1.3	NoYes	read-write	Clear on read
C64 genEquipServicesCetSpPmIngressPolicerStatiGreenPacket	1.3.6.1.4.1.2281.10.6.3.14.1.4	Counter64	read-only	green-packet
C64 genEquipServicesCetSpPmIngressPolicerStatiGreenBytes	1.3.6.1.4.1.2281.10.6.3.14.1.5	Counter64	read-only	green-bytes
C64 genEquipServicesCetSpPmIngressPolicerStatiYellowPacket	1.3.6.1.4.1.2281.10.6.3.14.1.6	Counter64	read-only	yellow-packet
C64 genEquipServicesCetSpPmIngressPolicerStatiYellowBytes	1.3.6.1.4.1.2281.10.6.3.14.1.7	Counter64	read-only	yellow-bytes
C64 genEquipServicesCetSpPmIngressPolicerStatiRedPacket	1.3.6.1.4.1.2281.10.6.3.14.1.8	Counter64	read-only	red-packet
C64 genEquipServicesCetSpPmIngressPolicerStatiRedBytes	1.3.6.1.4.1.2281.10.6.3.14.1.9	Counter64	read-only	red-bytes
genEquipServicesCETTmPmSpEgressQueueStatisticsTable	1.3.6.1.4.1.2281.10.6.3.15		not-accessible	Service Point egress queue statistics.
genEquipServicesCETTmPmSpEgressQueueStatisticsEntry	1.3.6.1.4.1.2281.10.6.3.15.1		not-accessible	Service Point egress queue statistics.
INT genEquipServicesCETTmPmSpEgressQueueStatisticsIfIndex	1.3.6.1.4.1.2281.10.6.3.15.1.1	INTEGER	read-only	ifindex
INT genEquipServicesCETTmPmSpEgressQueueStatisticsServiceIndex	1.3.6.1.4.1.2281.10.6.3.15.1.2	INTEGER	read-only	Servic class ID
INT genEquipServicesCETTmPmSpEgressQueueStatisticsCosQueueIndex	1.3.6.1.4.1.2281.10.6.3.15.1.3	INTEGER	read-only	cos-queue-index
NOY genEquipServicesCETTmPmSpEgressQueueStatisticsClearOnRead	1.3.6.1.4.1.2281.10.6.3.15.1.4	NoYes	read-write	Clear on read
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedGreenPacket	1.3.6.1.4.1.2281.10.6.3.15.1.5	Counter64	read-only	transmitted-green-packet
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedGreenBytes	1.3.6.1.4.1.2281.10.6.3.15.1.6	Counter64	read-only	transmitted-green-bytes
INT genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedGreenBitsPerSecond	1.3.6.1.4.1.2281.10.6.3.15.1.7	INTEGER	read-only	transmitted-green-bits-per-second
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsDroppedGreenPacket	1.3.6.1.4.1.2281.10.6.3.15.1.8	Counter64	read-only	dropped-green-packet
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsDroppedGreenBytes	1.3.6.1.4.1.2281.10.6.3.15.1.9	Counter64	read-only	dropped-green-bytes
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedYellowPacket	1.3.6.1.4.1.2281.10.6.3.15.1.10	Counter64	read-only	transmitted-yellow-packet
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedYellowBytes	1.3.6.1.4.1.2281.10.6.3.15.1.11	Counter64	read-only	transmitted-yellow-bytes
INT genEquipServicesCETTmPmSpEgressQueueStatisticsTransmittedYellowBitsPerSecond	1.3.6.1.4.1.2281.10.6.3.15.1.12	INTEGER	read-only	transmitted-yellow-bits-per-second
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsDroppedYellowPacket	1.3.6.1.4.1.2281.10.6.3.15.1.13	Counter64	read-only	dropped-yellow-packet
C64 genEquipServicesCETTmPmSpEgressQueueStatisticsDroppedYellowBytes	1.3.6.1.4.1.2281.10.6.3.15.1.14	Counter64	read-only	dropped-yellow-bytes
genEquipPmUtilization	1.3.6.1.4.1.2281.10.6.3.16
genEquipPmUtilizationCPU	1.3.6.1.4.1.2281.10.6.3.16.1
ENA genEquipPmUtilizationCPUAdmin	1.3.6.1.4.1.2281.10.6.3.16.1.1	EnableDisable	read-write	CPU utilization PM admin
INT genEquipPmUtilizationCPUThreshold	1.3.6.1.4.1.2281.10.6.3.16.1.2	INTEGER	read-write	User defined threshold for CPU utilization PM.
genEquipPmUtilizationCPUTable	1.3.6.1.4.1.2281.10.6.3.16.1.3		not-accessible	The CPU Utilization PMs
genEquipPmUtilizationCPUEntry	1.3.6.1.4.1.2281.10.6.3.16.1.3.1		not-accessible	The CPU Utilization PMs
PMT genEquipPmUtilizationCPUPmType	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmUtilizationCPUInterval	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmUtilizationCPUPeakUtilization	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.3	INTEGER	read-only	Peak CPU utilization of the current interval.
INT genEquipPmUtilizationCPUAverageUtilization	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.4	INTEGER	read-only	Average CPU utilization of the current interval.
INT genEquipPmUtilizationCPUMinimumUtilization	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.5	INTEGER	read-only	Minimal CPU utilization of the current interval.
INT genEquipPmUtilizationCPUExceedUtilization	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.6	INTEGER	read-only	Number of seconds in the current interval when CPU utilization exceeded user defined threshold.
NUM genEquipPmUtilizationCPUIDF	1.3.6.1.4.1.2281.10.6.3.16.1.3.1.7	Integrity	read-only	This value indicates if the IDF (Invalid Data Flag), was set.
genEquipPmUtilizationMem	1.3.6.1.4.1.2281.10.6.3.16.2
ENA genEquipPmUtilizationMemAdmin	1.3.6.1.4.1.2281.10.6.3.16.2.1	EnableDisable	read-write	Memory utilization PM admin
INT genEquipPmUtilizationMemThreshold	1.3.6.1.4.1.2281.10.6.3.16.2.2	INTEGER	read-write	Memory threshold for Ethernet port utilization PM.
genEquipPmUtilizationMemTable	1.3.6.1.4.1.2281.10.6.3.16.2.3		not-accessible	The Memory Utilization PMs
genEquipPmUtilizationMemEntry	1.3.6.1.4.1.2281.10.6.3.16.2.3.1		not-accessible	The Memory Utilization PMs
PMT genEquipPmUtilizationMemPmType	1.3.6.1.4.1.2281.10.6.3.16.2.3.1.1	PmTableType	read-only	This value indicates the PM Type table to access, 15 min, current 15 min, 24 hours or current 24 hours
INT genEquipPmUtilizationMemInterval	1.3.6.1.4.1.2281.10.6.3.16.2.3.1.2	INTEGER	read-only	The interval of the PM
INT genEquipPmUtilizationMemPeakUtilization	1.3.6.1.4.1.2281.10.6.3.16.2.3.1.3	INTEGER	read-only	Peak Memory utilization of the current interval.

RFC description

Microwave Radio Management performance monitoring MIB for tracking RFU signal levels, quality metrics, and radio link statistics.

Start monitoring Microwave radio link terminal (RF unit performance monitoring) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download MWRM-PM-MIB

What Is MWRM-PM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description