All MIBs › MWRM-RADIO-MIB
Category: Microwave/Radio
Description: Manages microwave radio module RF configuration, frequency, and link state.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MWRM-RADIO-MIB?
MWRM-RADIO-MIB is a vendor MIB for managing microwave radio module (RFU - Radio Frequency Unit) equipment, covering RF configuration, frequency planning, and link operational state for microwave point-to-point radio links. It exposes a status table for each RFU covering identifying data, RF type/grade, running firmware version, and live RF measurements. Its monitoring emphasis strongly covers hardware and RF-link health: it reports receive and transmit signal levels, diversity receive levels, transmit/receive frequency separation, module temperature, and running software version, which together reveal RF link degradation, overheating, or firmware drift on the radio unit. It is a self-contained equipment MIB (genEquip tree) but conceptually aligns with generic radio-link/interface monitoring standards for microwave transport. It is deployed on microwave radio backhaul links used by telecom operators for point-to-point transport between towers or base stations. Engineers can download the MWRM-RADIO-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MWRM-RADIO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Microwave radio (RFU) point-to-point backhaul unit
Monitoring Examples
An operator polls genEquipRfuStatusTable/genEquipRfuStatusEntry for a given genEquipRfuStatusId to check genEquipRfuStatusRxLevel and genEquipRfuStatusTxLevel, spotting a receive level drop that signals a fading or misaligned microwave link. genEquipRfuStatusTemperature reveals whether the RFU is overheating, while genEquipRfuStatusRunningVersion confirms firmware consistency across a link's two ends, and genEquipRfuStatusRxLevelDiversity helps validate that the diversity reception path is contributing properly to link quality.
What Can Be Monitored
- RF receive/transmit signal level
- diversity receive level
- RFU temperature
- running firmware version
- transmit/receive frequency separation
- RFU type and grade
This MIB depends on
Related MIBs
Imported Objects
From MWRM-UNIT-MIB
| AllowedNotAllowed | |
| BerLevel | |
| ClockSrc | |
| DownUp | |
| EnableDisable | |
| EnableDisableSMI2 | |
| GreenYellow | |
| HalfFull | |
| InputSeverity | |
| Integrity | |
| LoopbackType | |
| MetricImperial | |
| NoYes | |
| OffOn | |
| PmTableType | |
| ProgressStatus | |
| QueueName | |
| RadioId | |
| RateMbps | |
| RfuId | |
| Severity | |
| SignalLevel | |
| SlotId | |
| SupportedNotsupported | |
| SwCommand | |
| SwCommandTimer | |
| TrailIfType | |
| TrailProtectedType |
From RFC1213-MIB
| DisplayString |
From SNMPv2-SMI
| Counter64 | |
| IpAddress | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| MacAddress | |
| RowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| microwave_radio | 1.3.6.1.4.1.2281 | |||
| genEquip | 1.3.6.1.4.1.2281.10 | |||
| genEquipUnit | 1.3.6.1.4.1.2281.10.1 | |||
| genEquipRFU | 1.3.6.1.4.1.2281.10.5 | |||
| genEquipRfuStatusTable | 1.3.6.1.4.1.2281.10.5.1 | not-accessible | This table indicates the RFU Status Data. | |
| genEquipRfuStatusEntry | 1.3.6.1.4.1.2281.10.5.1.1 | not-accessible | Entry containing the data of the RFU. | |
| RFU genEquipRfuStatusId | 1.3.6.1.4.1.2281.10.5.1.1.1 | RfuId | read-only | This value indicates an index of a specific RFU |
| INT genEquipRfuStatusRxLevel | 1.3.6.1.4.1.2281.10.5.1.1.2 | INTEGER | read-only | This value indicates the RFU Receive Level Status. |
| INT genEquipRfuStatusTxLevel | 1.3.6.1.4.1.2281.10.5.1.1.3 | INTEGER | read-only | This value indicates the RFU Transmit Level Status. |
| INT genEquipRfuStatusTemperature | 1.3.6.1.4.1.2281.10.5.1.1.4 | INTEGER | read-only | This value indicates the RFU temperature. The value depends on the represented measurement system. with genEquipUnitMeasurementSystem parameter. |
| STR genEquipRfuStatusRunningVersion | 1.3.6.1.4.1.2281.10.5.1.1.5 | DisplayString | read-only | This value indicates the running SW version on the RFU. |
| INT genEquipRfuStatusRFUType | 1.3.6.1.4.1.2281.10.5.1.1.6 | INTEGER | read-only | The different types of the supported RFUs |
| RFU genEquipRfuStatusRFUGrade | 1.3.6.1.4.1.2281.10.5.1.1.7 | RfuGrade | read-only | The grade of the RFU |
| INT genEquipRfuStatusTxRxFreqSeparation | 1.3.6.1.4.1.2281.10.5.1.1.8 | INTEGER | read-only | Tx to Rx frequency separation (MHz), For some RFUs the user cannot set the Tx and Rx frequencies separately (one of them affects the other one's value). |
| INT genEquipRfuStatusRFUMode | 1.3.6.1.4.1.2281.10.5.1.1.9 | INTEGER | read-only | IF combining parameter - The mode of the RFU |
| INT genEquipRfuStatusRxLevelDiversity | 1.3.6.1.4.1.2281.10.5.1.1.10 | INTEGER | read-only | IF combining parameter - The Rx Diversity level (dBm) |
| INT genEquipRfuStatusRxLevelCombined | 1.3.6.1.4.1.2281.10.5.1.1.11 | INTEGER | read-only | IF combining parameter - The Rx Combined level (dBm) |
| INT genEquipRfuStatusAutoDelayCalStatus | 1.3.6.1.4.1.2281.10.5.1.1.12 | INTEGER | read-only | IF combining parameter - the automatic delay calibration status. Supported only for specific RFUs. |
| STR genEquipRfuStatusRFUSerialNumber | 1.3.6.1.4.1.2281.10.5.1.1.13 | DisplayString | read-only | RFU Serial number. |
| STR genEquipRfuStatusRFUPartNumber | 1.3.6.1.4.1.2281.10.5.1.1.14 | DisplayString | read-only | RFU Part number. |
| INT genEquipRfuStatusRFUmateCarrier | 1.3.6.1.4.1.2281.10.5.1.1.15 | INTEGER | read-only | The returned value indicates the slot number of the 'copartner RFU-D carrier'. The returned value will be '-1' when the RFU is not RFU-D, or if the 'copartner RFU-D' carrier is not found. |
| INT genEquipRfuStatusRFUMaxTxFreq | 1.3.6.1.4.1.2281.10.5.1.1.16 | INTEGER | read-only | The maximum Tx frequency of the RFU that is allowed by the RFU. |
| INT genEquipRfuStatusRFUMinTxFreq | 1.3.6.1.4.1.2281.10.5.1.1.17 | INTEGER | read-only | The minimum Tx frequency of the RFU that is allowed by the RFU. |
| INT genEquipRfuStatusRFUMaxRxFreq | 1.3.6.1.4.1.2281.10.5.1.1.18 | INTEGER | read-only | The maximum Rx frequency of the RFU that is allowed by the RFU. |
| INT genEquipRfuStatusRFUMinRxFreq | 1.3.6.1.4.1.2281.10.5.1.1.19 | INTEGER | read-only | The minimum Rx frequency of the RFU that is allowed by the RFU. |
| INT genEquipRfuStatusInstallation | 1.3.6.1.4.1.2281.10.5.1.1.20 | INTEGER | read-only | Returns 'all-indoor' or 'split' according to the RFU installation. |
| INT genEquipRfuStatusDataSciErrors | 1.3.6.1.4.1.2281.10.5.1.1.21 | INTEGER | read-only | Data Sci Errors |
| INT genEquipRfuStatusDeviceError | 1.3.6.1.4.1.2281.10.5.1.1.22 | INTEGER | read-only | Status Device Error |
| INT genEquipRfuStatusBand | 1.3.6.1.4.1.2281.10.5.1.1.23 | INTEGER | read-only | The Band of the RF-Module in GHz |
| INT genEquipRfuStatusPATemp | 1.3.6.1.4.1.2281.10.5.1.1.24 | INTEGER | read-only | The measured temperature in celsius of the PA (Power Amplifier) of the RF module |
| OFF genEquipRfuStatusTxMute | 1.3.6.1.4.1.2281.10.5.1.1.25 | OffOn | read-only | The mute status, whether it is on (mute) or off (un-mute) of the RF-Module |
| INT genEquipRfuStatusMinTxLevel | 1.3.6.1.4.1.2281.10.5.1.1.26 | INTEGER | read-only | The minimum feasible TX signal level (TSL) in dBm of the RF-Module |
| INT genEquipRfuStatusMaxTxLevel | 1.3.6.1.4.1.2281.10.5.1.1.27 | INTEGER | read-only | The maximum feasible TX signal level (TSL) in dBm of the RF-Module |
| INT genEquipRfuStatusMinBW | 1.3.6.1.4.1.2281.10.5.1.1.28 | INTEGER | read-only | The minimum supported bandwidth in KHz of the RF-Module |
| INT genEquipRfuStatusMaxBW | 1.3.6.1.4.1.2281.10.5.1.1.29 | INTEGER | read-only | The maximum supported bandwidth in KHz of the RF-Module |
| DOW genEquipRfuStatusCommunication | 1.3.6.1.4.1.2281.10.5.1.1.30 | DownUp | read-only | The communication status between the host and the RFU |
| INT genEquipRfuCfgATPCOverrideTimerState | 1.3.6.1.4.1.2281.10.5.1.1.31 | INTEGER | read-only | Returns the state of the ATPC 'override timer', whether it is regular or expired |
| SUP genEquipRfuStatusIfCombSupport | 1.3.6.1.4.1.2281.10.5.1.1.32 | SupportedNotsupported | read-only | Indicates if the IF-Combiner function is supported |
| INT genEquipRfuStatusMinRxLevel | 1.3.6.1.4.1.2281.10.5.1.1.33 | INTEGER | read-only | The minimum feasible RX signal level (RSL) in dBm of the RF-Module |
| INT genEquipRfuStatusMaxRxLevel | 1.3.6.1.4.1.2281.10.5.1.1.34 | INTEGER | read-only | The maximum feasible RX signal level (RSL) in dBm of the RF-Module |
| genEquipRfuCfgTable | 1.3.6.1.4.1.2281.10.5.2 | not-accessible | This table indicates the RFU Configuration. | |
| genEquipRfuCfgEntry | 1.3.6.1.4.1.2281.10.5.2.1 | not-accessible | This table indicates the RFU Configuration. | |
| RFU genEquipRfuCfgId | 1.3.6.1.4.1.2281.10.5.2.1.1 | RfuId | read-only | This value indicates an index of a specific RFU |
| INT genEquipRfuCfgMaxTxLevel | 1.3.6.1.4.1.2281.10.5.2.1.2 | INTEGER | read-write | This value indicates the RFU Maximum Transmit Level Configuration. |
| INT genEquipRfuCfgTxFreq | 1.3.6.1.4.1.2281.10.5.2.1.3 | INTEGER | read-write | Tx Frequency configuration (Mhz) |
| INT genEquipRfuCfgRxFreq | 1.3.6.1.4.1.2281.10.5.2.1.4 | INTEGER | read-write | Rx Frequency configuration (Mhz) |
| ENA genEquipRfuCfgATPCAdmin | 1.3.6.1.4.1.2281.10.5.2.1.5 | EnableDisable | read-write | ATPC configuration - Admin mode Possible values: - enable(2) - disable(3) |
| INT genEquipRfuCfgATPCRefRSL | 1.3.6.1.4.1.2281.10.5.2.1.6 | INTEGER | read-write | ATPC configuration - reference RSL level (dBm) |
| MUT genEquipRfuCfgMuteTx | 1.3.6.1.4.1.2281.10.5.2.1.7 | MuteOnOff | read-write | The required TX mute status of the RF-Module |
| INT genEquipRfuCfgRSLConnSrc | 1.3.6.1.4.1.2281.10.5.2.1.8 | INTEGER | read-write | IF combining - RFU RSL (Received Signal Level) connector source |
| INT genEquipRfuCfgDelayCal | 1.3.6.1.4.1.2281.10.5.2.1.9 | INTEGER | read-write | IF combining - Delay calibration |
| INT genEquipRfuCfgLoopback | 1.3.6.1.4.1.2281.10.5.2.1.10 | INTEGER | read-write | RFU RF loopback command |
| ENA genEquipRfuCfgLogAdmin | 1.3.6.1.4.1.2281.10.5.2.1.11 | EnableDisable | read-write | RFU internal log file admin Possible values: - enable(2) - disable(3) |
| OFF genEquipRfuCfgClearComDeviceError | 1.3.6.1.4.1.2281.10.5.2.1.12 | OffOn | read-write | Clear Com device Error. |
| ENA genEquipRfuCfgGreenModeAdmin | 1.3.6.1.4.1.2281.10.5.2.1.13 | EnableDisable | read-write | Enables/disables RFU green mode. This mode will minimize power consumption while ensuring the highest transmission power possible to get an RSL not higher than defined in the reference level genEquipRfuCfgGreenModeReferenceLevel |
| INT genEquipRfuCfgGreenModeReferenceLevel | 1.3.6.1.4.1.2281.10.5.2.1.14 | INTEGER | read-write | RSL reference level (in dB) for green mode operation |
| INT genEquipRfuCfgATPCOverrideTxLevel | 1.3.6.1.4.1.2281.10.5.2.1.15 | INTEGER | read-write | This parameter configures the default transmission signal level in case of ATPC override due to expiration of maximum power timer as defined in genEquipRfuCfgATPCOverrideTimeout. |
| INT genEquipRfuCfgATPCOverrideTimeout | 1.3.6.1.4.1.2281.10.5.2.1.16 | INTEGER | read-write | This parameter configures the timer to be counted while in ATPC in case of maximum power transmission. If this timer expires, the system will transmit at a default level defined in genEquipRfuCfgATPCOverrideTxLevel |
| INT genEquipRfuCfgATPCOverrideTimerCounter | 1.3.6.1.4.1.2281.10.5.2.1.17 | INTEGER | read-only | This parameter shows the time left in the timer defined by genEquipRfuCfgATPCOverrideTxLevel |
| OFF genEquipRfuCfgATPCOverrideTimerCancel | 1.3.6.1.4.1.2281.10.5.2.1.18 | OffOn | read-write | Setting this parameter to ON will cancel the ATPC override mode. This will only be effective while in this mode i.e. the system had been transmitting at maximum power for a time longer than defined in genEquipRfuCfgATPCOverrideTxLevel and now is transmitting at the default level defined in genEquipRfuCfgATPCOverrideTxLevel. Following execution, the system will go back to normal ATPC operating mode |
| genEquipRfuUploadTable | 1.3.6.1.4.1.2281.10.5.3 | not-accessible | RFU Upload Data table. | |
| genEquipRfuUploadEntry | 1.3.6.1.4.1.2281.10.5.3.1 | not-accessible | Entry containing the data of the RFU. | |
| OID genEquipRfuUploadId | 1.3.6.1.4.1.2281.10.5.3.1.1 | RadioId | read-only | This value indicates an index of a specific RFU |
| INT genEquipRfuUploadSwCommand | 1.3.6.1.4.1.2281.10.5.3.1.2 | INTEGER | read-write | This value initiates SW upload to the RFU. |
| INT genEquipRfuUploadSwStatus | 1.3.6.1.4.1.2281.10.5.3.1.3 | INTEGER | read-only | This value indicates the status of the SW load operation on the RFU. |
| INT genEquipRfuUploadCounter | 1.3.6.1.4.1.2281.10.5.3.1.4 | INTEGER | read-only | This parameter shows the progress (in blocks) of RFU software download |
| genEquipRFUNG | 1.3.6.1.4.1.2281.10.5.4 | |||
| genEquipRfuSwInstallTable | 1.3.6.1.4.1.2281.10.5.4.2 | not-accessible | RFU software managemet install configuration. | |
| genEquipRfuSwInstallEntry | 1.3.6.1.4.1.2281.10.5.4.2.1 | not-accessible | RFU software managemet install configuration. | |
| INT genEquipRfuSwInstallIfIndex | 1.3.6.1.4.1.2281.10.5.4.2.1.1 | INTEGER | read-only | RFU ifIndex |
| INT genEquipRfuSwInstallOperation | 1.3.6.1.4.1.2281.10.5.4.2.1.2 | INTEGER | read-write | RFU software installation operation to be performed. |
| NOY genEquipRfuSwInstallTimedInstallation | 1.3.6.1.4.1.2281.10.5.4.2.1.3 | NoYes | read-write | Determines whether the installation will be carried out after a configured timer. |
| INT genEquipRfuSwInstallTimer | 1.3.6.1.4.1.2281.10.5.4.2.1.4 | INTEGER | read-write | Timer for timed installations |
| genEquipRfuInstalledVersionsTable | 1.3.6.1.4.1.2281.10.5.4.3 | not-accessible | RFU software managemet installed versuion. | |
| genEquipRfuInstalledVersionsEntry | 1.3.6.1.4.1.2281.10.5.4.3.1 | not-accessible | RFU software managemet installed version. | |
| INT genEquipRfuInstalledVersionsIfIndex | 1.3.6.1.4.1.2281.10.5.4.3.1.1 | INTEGER | read-only | RFU ifIndex |
| STR genEquipRfuInstalledVersionsDSP | 1.3.6.1.4.1.2281.10.5.4.3.1.2 | DisplayString | read-only | RFU version DSP. |
| STR genEquipRfuInstalledVersionsConfigurations | 1.3.6.1.4.1.2281.10.5.4.3.1.3 | DisplayString | read-only | Configuration tables. |
| STR genEquipRfuInstalledVersionsConstants | 1.3.6.1.4.1.2281.10.5.4.3.1.4 | DisplayString | read-only | Constant tables |
| STR genEquipRfuInstalledVersionsScripts | 1.3.6.1.4.1.2281.10.5.4.3.1.5 | DisplayString | read-only | RFU scripts |
| STR genEquipRfuInstalledVersionsFirmware | 1.3.6.1.4.1.2281.10.5.4.3.1.6 | DisplayString | read-only | Firmware |
| genEquipRfuSwStatusTable | 1.3.6.1.4.1.2281.10.5.4.4 | not-accessible | RFU software managemet installed status. | |
| genEquipRfuSwStatusEntry | 1.3.6.1.4.1.2281.10.5.4.4.1 | not-accessible | RFU software managemet installed status. | |
| INT genEquipRfuSwStatusIfIndex | 1.3.6.1.4.1.2281.10.5.4.4.1.1 | INTEGER | read-only | RFU ifIndex |
| RFU genEquipRfuSwStatusCurrentState | 1.3.6.1.4.1.2281.10.5.4.4.1.2 | RFUSoftwareInstallStat | read-only | Current state of the install operation. |
| INT genEquipRfuSwStatusProgress | 1.3.6.1.4.1.2281.10.5.4.4.1.3 | INTEGER | read-only | Progress of the current install operation in percentage. |
| genEquipRfuRunningVersionsTable | 1.3.6.1.4.1.2281.10.5.4.5 | not-accessible | RFU software managemet rinning versions. | |
| genEquipRfuRunningVersionsEntry | 1.3.6.1.4.1.2281.10.5.4.5.1 | not-accessible | RFU software managemet running versions. | |
| INT genEquipRfuRunningVersionsIfIndex | 1.3.6.1.4.1.2281.10.5.4.5.1.1 | INTEGER | read-only | RFU ifIndex |
| STR genEquipRfuRunningVersionsDSP | 1.3.6.1.4.1.2281.10.5.4.5.1.2 | DisplayString | read-only | DSP. |
| STR genEquipRfuRunningVersionsConfigurations | 1.3.6.1.4.1.2281.10.5.4.5.1.3 | DisplayString | read-only | Configuration tables. |
| STR genEquipRfuRunningVersionsConstants | 1.3.6.1.4.1.2281.10.5.4.5.1.4 | DisplayString | read-only | Constant tables. |
| STR genEquipRfuRunningVersionsScripts | 1.3.6.1.4.1.2281.10.5.4.5.1.5 | DisplayString | read-only | RFU scripts. |
| STR genEquipRfuRunningVersionsFirmware | 1.3.6.1.4.1.2281.10.5.4.5.1.6 | DisplayString | read-only | Firmware. |
| genEquipRfuAvailableVersionsTable | 1.3.6.1.4.1.2281.10.5.4.6 | not-accessible | RFU software managemet available versions. | |
| genEquipRfuAvailableVersionsEntry | 1.3.6.1.4.1.2281.10.5.4.6.1 | not-accessible | RFU software managemet available versions. | |
| RFU genEquipRfuAvailableVersionsRfuType | 1.3.6.1.4.1.2281.10.5.4.6.1.1 | RfuMajorType | read-only | RFU Type |
| STR genEquipRfuAvailableVersionsDSP | 1.3.6.1.4.1.2281.10.5.4.6.1.2 | DisplayString | read-only | DSP. |
| STR genEquipRfuAvailableVersionsConfigurations | 1.3.6.1.4.1.2281.10.5.4.6.1.3 | DisplayString | read-only | Configuration tables. |
| STR genEquipRfuAvailableVersionsConstants | 1.3.6.1.4.1.2281.10.5.4.6.1.4 | DisplayString | read-only | Constant tables. |
| STR genEquipRfuAvailableVersionsScripts | 1.3.6.1.4.1.2281.10.5.4.6.1.5 | DisplayString | read-only | RFU scripts. |
| STR genEquipRfuAvailableVersionsFirmware | 1.3.6.1.4.1.2281.10.5.4.6.1.6 | DisplayString | read-only | Firmware. |
| genEquipRadio | 1.3.6.1.4.1.2281.10.7 | |||
| genEquipRadioStatusTable | 1.3.6.1.4.1.2281.10.7.1 | not-accessible | Radio status table | |
| genEquipRadioStatusEntry | 1.3.6.1.4.1.2281.10.7.1.1 | not-accessible | Radio status table | |
| OID genEquipRadioStatusRadioId | 1.3.6.1.4.1.2281.10.7.1.1.1 | RadioId | read-only | This value is the radio ID that serves as the table Index. |
| INT genEquipRadioStatusMSE | 1.3.6.1.4.1.2281.10.7.1.1.2 | INTEGER | read-only | MSE (Mean Square Error) of the Rx signal (measured in dB * 100). -9900 value (-99.00 dB) means that the signal is not locked. ~ -3500 value (-35.00 dB) is a good MSE. |
| INT genEquipRadioStatusDefectedBlocks | 1.3.6.1.4.1.2281.10.7.1.1.3 | INTEGER | read-only | The number of counted defective radio blocks. |
| THR genEquipRadioStatusBER | 1.3.6.1.4.1.2281.10.7.1.1.4 | ThresholdExponent | read-only | The measured BER (Bit Error Rate) level of the modem. |
| INT genEquipRadioStatusXPI | 1.3.6.1.4.1.2281.10.7.1.1.5 | INTEGER | read-only | XPI (Cross Polar Interference) level measured by the modem. |
| ENA genEquipRadioStatusXPICEnabled | 1.3.6.1.4.1.2281.10.7.1.1.6 | EnableDisableSMI2 | read-only | This parameter indicates whether an XPIC script is currently loaded. |
| genEquipRadioCfgTable | 1.3.6.1.4.1.2281.10.7.2 | not-accessible | Radio Configuration table. | |
| genEquipRadioCfgEntry | 1.3.6.1.4.1.2281.10.7.2.1 | not-accessible | Radio Configuration table. | |
| OID genEquipRadioCfgRadioId | 1.3.6.1.4.1.2281.10.7.2.1.1 | RadioId | read-only | This value is the radio ID that serves as this table Index |
| INT genEquipRadioCfgLinkId | 1.3.6.1.4.1.2281.10.7.2.1.2 | INTEGER | read-write | Radio configuration link ID |
| ENA genEquipRadioCfgMACHeaderCompression | 1.3.6.1.4.1.2281.10.7.2.1.3 | EnableDisable | read-write | The Admin state of the MAC header compression. |
| OFF genEquipRadioCfgClearCounters | 1.3.6.1.4.1.2281.10.7.2.1.4 | OffOn | read-write | Setting this parameter to ON will clear the radio counters. |
| INT genEquipRadioCfgIfLoopback | 1.3.6.1.4.1.2281.10.7.2.1.5 | INTEGER | read-write | The administrative state of the IF loopback. |
| THR genEquipRadioCfgExcessiveBERThreshold | 1.3.6.1.4.1.2281.10.7.2.1.6 | ThresholdExponent | read-write | The BER threshold that when exceeded will be considered as 'Excessive BER'. |
| THR genEquipRadioCfgSignalDegradeThreshold | 1.3.6.1.4.1.2281.10.7.2.1.7 | ThresholdExponent | read-write | The BER (Bit Error Rate) threshold that when exceeded will be considered as 'Signal Degrade'. |
| ENA genEquipRadioCfgRadioAdmin | 1.3.6.1.4.1.2281.10.7.2.1.8 | EnableDisable | read-write | Radio Admin state (Enable,Disable) can be used in ifTable::ifAdminStatus |
| DOW genEquipRadioCfgRadioOperationalStatus | 1.3.6.1.4.1.2281.10.7.2.1.9 | DownUp | read-only | The operational status of the radio interface. |
| INT genEquipRadioCfgRadioTrafficPriorityScheme | 1.3.6.1.4.1.2281.10.7.2.1.10 | INTEGER | read-write | this parameter configures the relative priority of different traffic streams. High-tdm-over-high-ethernet gives priorities as follows: (1) TDM high priority (2) Ethernet high priority (3) TDM low priority (4) Etherenet low priority. High-Ethernet-over-tdm gives priorities as follows: (1) Ethernet high priority (2) TDM high priority (3) TDM low priority (4) Etherenet low priority. Tdm-over-ethernet gives priorities as follows: (1) TDM high priority (2) TDM low priority (3) Ethernet |
| INT genEquipRadioCfgRadioHiPriorityEthernetBW | 1.3.6.1.4.1.2281.10.7.2.1.11 | INTEGER | read-write | this parameter configures the amount of bandwith reserved for high-priority Ethernet. It must be a number in resolution of 2.048 Mbit/s for E1 systems or 1.544 Mbit/s for T1 systems. The maximum possible capacity is given by genEquipRadioCfgRadioCurrentAvailableCapacity |
| ENA genEquipRadioCfgRadioMultiRadioEnable | 1.3.6.1.4.1.2281.10.7.2.1.12 | EnableDisable | read-write | this parameter enables/disables the multi-radio feature for this radio. Notice that for the feature to work it must be configured in two adjacent radios (odd and even slots) |
| INT genEquipRadioCfgRadioMultiRadioBlockLocalTraffic | 1.3.6.1.4.1.2281.10.7.2.1.13 | INTEGER | read-write | this parameter allows stopping distribution of data to different radios in Multi-Radio mode for debugging purposes |
| INT genEquipRadioCfgRadioMultiRadioBlockMateTraffic | 1.3.6.1.4.1.2281.10.7.2.1.14 | INTEGER | read-write | this parameter allows stopping distribution of data to the radio in the mate IDU in Multi-Radio mode for debugging purposes |
| INT genEquipRadioCfgRadioCurrentAvailableCapacity | 1.3.6.1.4.1.2281.10.7.2.1.15 | INTEGER | read-only | This parameter indicates the maximum possible capacity available for Ethernet. This sets a top limit for amount of high-priority Ethernet bandwidth |
| ENA genEquipRadioCfgRadioMultiRadioExcessiveBERAdmin | 1.3.6.1.4.1.2281.10.7.2.1.16 | EnableDisable | read-write | This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in case of an excessive BER condition |
| ENA genEquipRadioCfgRadioMultiRadioSignalDegradeAdmin | 1.3.6.1.4.1.2281.10.7.2.1.17 | EnableDisable | read-write | This parameter configures whether in Multi-Radio mode data stops being distributed to the radio in case of a signal degraded condition |
| ENA genEquipRadioCfgEnAlarmGenOnRslDegrade | 1.3.6.1.4.1.2281.10.7.2.1.18 | EnableDisable | read-write | TEnable/Disable alarm and trapgeneration on RSL degradationbelow user defined threshold.If enabled, trap and alarm willbe generated when current RSLlevel degrades below userdefined threshold for 5subsequent seconds. Alarm willbe cleared after RSL level staysabove the threshold for at leastanother 5 seconds. Thresholdis calculated as a nominal RSLlevel minus the degradationmargin. |
| INT genEquipRadioCfgAlarmGenRslNominalLevel | 1.3.6.1.4.1.2281.10.7.2.1.19 | INTEGER | read-write | RSL nominal level [in dBm] foralarm and event generation. |
| INT genEquipRadioCfgAlarmGenRslDegradationMargin | 1.3.6.1.4.1.2281.10.7.2.1.20 | INTEGER | read-write | RSL degradation margin [in dB]for alarm and eventgeneration. The margin isrelative to the nominal RSLlevel |
| ENA genEquipRadioCfgLinkShutDownOnRadioFailure | 1.3.6.1.4.1.2281.10.7.2.1.21 | EnableDisable | read-write | This parameter enables shutting down the link and initiating automatic state propagation upon a failure in each one of the radios. Radio failure condition is determined by user configurations and can be one of the following: Radio LOF, Link ID mismatch, Radio excessive BER, Radio signal degrade, Link ID mismatch. |
| INT genEquipRadioCfgLoopbackTimeout | 1.3.6.1.4.1.2281.10.7.2.1.22 | INTEGER | read-write | The timeout in minutes for automatic termination of the loopback. The value '0' refers to 'no timeout'. |
| INT genEquipRadioCfgAbcMode | 1.3.6.1.4.1.2281.10.7.2.1.23 | INTEGER | read-write | TThe radio mode (multi direction or multi carrier). |
| genEquipRemoteRadio | 1.3.6.1.4.1.2281.10.7.3 | |||
| genEquipRemoteRadioTable | 1.3.6.1.4.1.2281.10.7.3.1 | not-accessible | Remote radio table. | |
| genEquipRemoteRadioEntry | 1.3.6.1.4.1.2281.10.7.3.1.1 | not-accessible | Remote radio table. | |
| OID genEquipRemoteRadioRadioId | 1.3.6.1.4.1.2281.10.7.3.1.1.1 | RadioId | read-only | This value is the radio ID that serves as this table Index |
| DOW genEquipRemoteRadioRemoteCommunication | 1.3.6.1.4.1.2281.10.7.3.1.1.2 | DownUp | read-only | The operational status of the remote radio. |
| IP genEquipRemoteRadioRemoteIPAddr | 1.3.6.1.4.1.2281.10.7.3.1.1.3 | IpAddress | read-write | The remote Ip address. |
| INT genEquipRemoteRadioRemoteRxLevel | 1.3.6.1.4.1.2281.10.7.3.1.1.4 | INTEGER | read-only | The Rx level of the remote radio (in dBm) |
| INT genEquipRemoteRadioRemoteForceMaxTxLevel | 1.3.6.1.4.1.2281.10.7.3.1.1.5 | INTEGER | read-write | Command that forces the remote radio maximum Tx level (in dBm) |
| INT genEquipRemoteRadioRemoteTxFreq | 1.3.6.1.4.1.2281.10.7.3.1.1.6 | INTEGER | read-write | The remote radio Tx frequancy (in MHz). |
| INT genEquipRemoteRadioRemoteRxFreq | 1.3.6.1.4.1.2281.10.7.3.1.1.7 | INTEGER | read-write | The remote radio Rx frequancy (in MHz). |
| INT genEquipRemoteRadioRemoteATPCReferenceRxLevel | 1.3.6.1.4.1.2281.10.7.3.1.1.8 | INTEGER | read-write | The RSL reference level for the ATPC mechanism in the remote radio. |
| IP genEquipRemoteRadioRemoteFloatingIPAddr | 1.3.6.1.4.1.2281.10.7.3.1.1.9 | IpAddress | read-write | This value indicates the floating IP address used in the remote shelf if its main units are in 1+1 protection mode. |
| IP genEquipRemoteRadioRemoteDefaultGateway | 1.3.6.1.4.1.2281.10.7.3.1.1.10 | IpAddress | read-only | Default gateway of remote NE (Network Element) across this radio link. |
| SEV genEquipRemoteRadioRemoteMostSevereAlarm | 1.3.6.1.4.1.2281.10.7.3.1.1.11 | Severity | read-only | Most severe alarm of remote NE (Network Element) across this radio link. |
| IP genEquipRemoteRadioRemoteSubnetMask | 1.3.6.1.4.1.2281.10.7.3.1.1.12 | IpAddress | read-only | Subnet mask of remote NE (Network Element) across this radio link. |
| INT genEquipRemoteRadioRemoteSlotID | 1.3.6.1.4.1.2281.10.7.3.1.1.13 | INTEGER | read-only | The remote radio slot number. |
| OFF genEquipRemoteRadioRemoteForceTxMute | 1.3.6.1.4.1.2281.10.7.3.1.1.14 | OffOn | read-write | Force the mute state of the remote unit radio interface. |
| INT genEquipRemoteRadioRemoteLinkId | 1.3.6.1.4.1.2281.10.7.3.1.1.15 | INTEGER | read-write | The Link Id of the remote unit radio interface. |
| NOY genEquipRemoteRadioRemoteATPCoverrideState | 1.3.6.1.4.1.2281.10.7.3.1.1.16 | NoYes | read-only | Remote Radio ATPC Override Timer expire state. |
| NOY genEquipRemoteRadioRemoteATPCoverrideStateCancel | 1.3.6.1.4.1.2281.10.7.3.1.1.17 | NoYes | read-write | his coomand cancel remote ATPC override state. |
| ENA genEquipRemoteRadioRemoteDataLoopBackAdmin | 1.3.6.1.4.1.2281.10.7.3.1.1.18 | EnableDisable | read-write | Remote unit administrator state of data loopback. |
| INT genEquipRemoteRadioRemoteDataLoopBackDuration | 1.3.6.1.4.1.2281.10.7.3.1.1.19 | INTEGER | read-write | Remote Data LoopBack Duration at remote unit[Minutes], zero for infinite loop back. |
| ENA genEquipRemoteRadioRemoteDataLoopBackSwitchAddress | 1.3.6.1.4.1.2281.10.7.3.1.1.20 | EnableDisable | read-write | Remote Unit switch MAC DA. |
| INT genEquipRemoteRadioRemoteGreenReferenceRxLevel | 1.3.6.1.4.1.2281.10.7.3.1.1.21 | INTEGER | read-only | Remote Radio Green RSL reference level[dBm]. |
| INT genEquipRemoteRadioRemoteMNGvlan | 1.3.6.1.4.1.2281.10.7.3.1.1.22 | INTEGER | read-write | Remote Management Vlan. |
| FAL genEquipRemoteRadioRemoteReset | 1.3.6.1.4.1.2281.10.7.3.1.1.23 | FalseTrue | read-write | Remote reset of unit. |
| ENA genEquipRemoteRadioRemoteGreenModeAdmin | 1.3.6.1.4.1.2281.10.7.3.1.1.24 | EnableDisable | read-write | Remote Unit Tx Green Mode Admin. |
| COM genEquipRemoteRadioRemoteWebProtocol | 1.3.6.1.4.1.2281.10.7.3.1.1.25 | CommunicationChannel | read-write | Remote web protocol. |
| OCT genEquipRemoteRadioRemoteIPv6Addr | 1.3.6.1.4.1.2281.10.7.3.1.1.26 | OCTET STRING | read-write | Remote IPv6 Address. |
| INT genEquipRemoteRadioRemotePrefixLength | 1.3.6.1.4.1.2281.10.7.3.1.1.27 | INTEGER | read-write | Remote IPv6 Subnet-Mask. |
| OCT genEquipRemoteRadioRemoteDefaultGatewayIpv6 | 1.3.6.1.4.1.2281.10.7.3.1.1.28 | OCTET STRING | read-write | Remote IPv6 Default Gateway. |
| FAL genEquipRemoteRadioRemoteResetSlot | 1.3.6.1.4.1.2281.10.7.3.1.1.29 | FalseTrue | read-write | Remote Unit Reset Slot. |
| genEquipRadioMRMC | 1.3.6.1.4.1.2281.10.7.4 | |||
| genEquipRadioMRMCTable | 1.3.6.1.4.1.2281.10.7.4.1 | not-accessible | MRMC stauts table (Multi rate multi constellation) | |
| genEquipRadioMRMCEntry | 1.3.6.1.4.1.2281.10.7.4.1.1 | not-accessible | MRMC status table (Multi rate multi constellation) | |
| OID genEquipRadioMRMCRadioId | 1.3.6.1.4.1.2281.10.7.4.1.1.1 | RadioId | read-only | This value is the radio ID that serves as this table Index |
| INT genEquipRadioMRMCSelectedScriptIndex | 1.3.6.1.4.1.2281.10.7.4.1.1.2 | INTEGER | read-write | The index of the MRMC script. The description of the script located in the genEquipRadioMRMCScriptTable. |
| INT genEquipRadioMRMCOccupidBandwidth | 1.3.6.1.4.1.2281.10.7.4.1.1.3 | INTEGER | read-only | The Occupid Bandwidth (in KHz). |
| INT genEquipRadioMRMCOperMode | 1.3.6.1.4.1.2281.10.7.4.1.1.4 | INTEGER | read-only | The Mode of the MRMC script. |
| MRM genEquipRadioMRMCCurrTxProfile | 1.3.6.1.4.1.2281.10.7.4.1.1.5 | MrmcProfile | read-only | The Tx profile number. |
| INT genEquipRadioMRMCCurrTxQAM | 1.3.6.1.4.1.2281.10.7.4.1.1.6 | INTEGER | read-only | The current Tx QAM (modulation). |
| MRM genEquipRadioMRMCCurrTxBitrate | 1.3.6.1.4.1.2281.10.7.4.1.1.7 | MrmcBitRate | read-only | The current Tx bit rate (in Kbps) |
| INT genEquipRadioMRMCCurrTxVc | 1.3.6.1.4.1.2281.10.7.4.1.1.8 | INTEGER | read-only | The current number of Tx TDM channels. |
| MRM genEquipRadioMRMCCurrRxProfile | 1.3.6.1.4.1.2281.10.7.4.1.1.9 | MrmcProfile | read-only | The current Rx profile number |
| INT genEquipRadioMRMCCurrRxQAM | 1.3.6.1.4.1.2281.10.7.4.1.1.10 | INTEGER | read-only | The current Rx QAM (modulation). |
| MRM genEquipRadioMRMCCurrRxBitrate | 1.3.6.1.4.1.2281.10.7.4.1.1.11 | MrmcBitRate | read-only | The current total Rx bit rate (in Kbps) |
| INT genEquipRadioMRMCCurrRxVc | 1.3.6.1.4.1.2281.10.7.4.1.1.12 | INTEGER | read-only | The current number of Rx TDM channels. |
| RFU genEquipRadioMRMCCurrGrade | 1.3.6.1.4.1.2281.10.7.4.1.1.13 | RfuGrade | read-only | The grade of the current script. |
| ENA genEquipRadioMRMCEnAlarmOnAcmProfileDegrade | 1.3.6.1.4.1.2281.10.7.4.1.1.14 | EnableDisable | read-write | Enable/Disable event and trapgeneration on ACM profiledegrade. When enabled and ifcurrent radio script supports Adaptive Code Modulation(ACM) event and trap will begenerated upon ACM profiledegradation below userdefinedthreshold. Alarm willbe generated only if the ACMprofile stays below thethreshold for at least 5 subsequent seconds. Alarm willbe cleared after ACM profilereturns to be above thethreshold again. |
| INT genEquipRadioMRMCAlarmOnAcmProfileDegradeThreshold | 1.3.6.1.4.1.2281.10.7.4.1.1.15 | INTEGER | read-write | ACM profile threshold foralarm generation |
| genEquipRadioMRMCScriptTable | 1.3.6.1.4.1.2281.10.7.4.2 | not-accessible | The MRMC script table. | |
| genEquipRadioMRMCScriptEntry | 1.3.6.1.4.1.2281.10.7.4.2.1 | not-accessible | The MRMC script table. | |
| OID genEquipRadioMRMCScriptRadioId | 1.3.6.1.4.1.2281.10.7.4.2.1.1 | RadioId | read-only | This value is the radio ID that serves as this table Index |
| INT genEquipRadioMRMCScriptIndex | 1.3.6.1.4.1.2281.10.7.4.2.1.2 | INTEGER | read-only | The index of the MRMC scripts. |
| STR genEquipRadioMRMCScriptName | 1.3.6.1.4.1.2281.10.7.4.2.1.3 | DisplayString | read-only | The MRMC script name. |
| INT genEquipRadioMRMCScriptOperMode | 1.3.6.1.4.1.2281.10.7.4.2.1.4 | INTEGER | read-only | The script operational mode. |
| MRM genEquipRadioMRMCScriptProfile | 1.3.6.1.4.1.2281.10.7.4.2.1.5 | MrmcProfile | read-only | The profile number of the script |
| MRM genEquipRadioMRMCScriptProfileBitrate | 1.3.6.1.4.1.2281.10.7.4.2.1.6 | MrmcBitRate | read-only | The Bit rate of the MRMC profile (in Kbps). |
| INT genEquipRadioMRMCScriptAdaptivePower | 1.3.6.1.4.1.2281.10.7.4.2.1.7 | INTEGER | read-only | 'Adaptive Power' option which is available only when operation mode is ACM-adaptive |
| INT genEquipRadioMRMCScriptReference | 1.3.6.1.4.1.2281.10.7.4.2.1.8 | INTEGER | read-only | 'Reference Class' option which is available only when operation mode 'ACM-adaptive' AND 'Adaptive Power' are enabled. |
| MRM genEquipRadioMRMCScriptMinProfile | 1.3.6.1.4.1.2281.10.7.4.2.1.9 | MrmcProfile | read-only | 'Minimum Profile' option which is available only when operation mode 'ACM-adaptive' AND 'Adaptive Power' are enabled. It state the minimum profile level for this script. |
| genEquipRadioMRMCFilteredTable | 1.3.6.1.4.1.2281.10.7.4.3 | not-accessible | Filtered MRMC scripts table. | |
| genEquipRadioMRMCFilteredEntry | 1.3.6.1.4.1.2281.10.7.4.3.1 | not-accessible | List of the filtered MRMC scripts. | |
| OID genEquipRadioMRMCFilteredRadioId | 1.3.6.1.4.1.2281.10.7.4.3.1.1 | RadioId | read-only | The index of the radio interface |
| MRM genEquipRadioMRMCFilteredScriptId | 1.3.6.1.4.1.2281.10.7.4.3.1.2 | MrmcScriptId | read-only | The MRMC filtered script IDs that are available in the specific radio. |
| genEquipRadioMRMCProfileAttrTable | 1.3.6.1.4.1.2281.10.7.4.4 | not-accessible | MRMC profile attribute table. | |
| genEquipRadioMRMCProfileAttrEntry | 1.3.6.1.4.1.2281.10.7.4.4.1 | not-accessible | MRMC script profile's attributes. | |
| MRM genEquipRadioMRMCProfileAttrScriptId | 1.3.6.1.4.1.2281.10.7.4.4.1.1 | MrmcScriptId | read-only | The index of the table |
| MRM genEquipRadioMRMCProfileAttrTxProfile | 1.3.6.1.4.1.2281.10.7.4.4.1.2 | MrmcProfile | read-only | The profile number of the TX channel. |
| MRM genEquipRadioMRMCProfileAttrRxProfile | 1.3.6.1.4.1.2281.10.7.4.4.1.3 | MrmcProfile | read-only | The profile number of the RX channel. |
| QAM genEquipRadioMRMCProfileAttrTxQAM | 1.3.6.1.4.1.2281.10.7.4.4.1.4 | QamOrder | read-only | Indicates the QAM level of the TX channel. |
| MRM genEquipRadioMRMCProfileAttrTxBitRate | 1.3.6.1.4.1.2281.10.7.4.4.1.5 | MrmcBitRate | read-only | Indicates the TX bit-rate of the profile. |
| QAM genEquipRadioMRMCProfileAttrRxQAM | 1.3.6.1.4.1.2281.10.7.4.4.1.6 | QamOrder | read-only | Indicates the QAM level of the RX channel. |
| MRM genEquipRadioMRMCProfileAttrRxBitRate | 1.3.6.1.4.1.2281.10.7.4.4.1.7 | MrmcBitRate | read-only | RX bit-rate of the profile. |
| genEquipRadioMRMCScriptAttrTable | 1.3.6.1.4.1.2281.10.7.4.5 | not-accessible | MRMC script attribute table. | |
| genEquipRadioMRMCScriptAttrEntry | 1.3.6.1.4.1.2281.10.7.4.5.1 | not-accessible | MRMC script attributes. | |
| MRM genEquipRadioMRMCScriptAttrScriptId | 1.3.6.1.4.1.2281.10.7.4.5.1.1 | MrmcScriptId | read-only | The ID of the MRMC script. |
| STR genEquipRadioMRMCScriptAttrScriptName | 1.3.6.1.4.1.2281.10.7.4.5.1.2 | DisplayString | read-only | The name that identifies the script. |
| NOY genEquipRadioMRMCScriptAttrSupportACM | 1.3.6.1.4.1.2281.10.7.4.5.1.3 | NoYes | read-only | Indicates if the MRMC script supports ACM (Adaptive Coding Modulation) functionality |
| INT genEquipRadioMRMCScriptAttrStandard | 1.3.6.1.4.1.2281.10.7.4.5.1.4 | INTEGER | read-only | The standard that the MRMC script is designed to comply with. |
| INT genEquipRadioMRMCScriptAttrMultiCarrier | 1.3.6.1.4.1.2281.10.7.4.5.1.5 | INTEGER | read-only | Indicates whether the MRMC script support a single carrier or any kind of multi carrier. |
| NOY genEquipRadioMRMCScriptAttrAdjChannel | 1.3.6.1.4.1.2281.10.7.4.5.1.6 | NoYes | read-only | Indicates whether the MRMC script supports adjacent channel |
| INT genEquipRadioMRMCScriptAttrModScheme | 1.3.6.1.4.1.2281.10.7.4.5.1.7 | INTEGER | read-only | Indicates whether the MRMC script supports fixed or adaptive (ACM) modulation scheme. |
| INT genEquipRadioMRMCScriptAttrSymmetry | 1.3.6.1.4.1.2281.10.7.4.5.1.8 | INTEGER | read-only | Indicates whether the MRMC script is designed to normal (symmetrical) BW or an Asymmetrical BW. |
| INT genEquipRadioMRMCScriptAttrLatency | 1.3.6.1.4.1.2281.10.7.4.5.1.9 | INTEGER | read-only | The Latency level of the MRMC Script. |
| INT genEquipRadioMRMCScriptAttrTxBW | 1.3.6.1.4.1.2281.10.7.4.5.1.10 | INTEGER | read-only | The TX channel bandwidth (channel spacing) of the MRMC script. |
| INT genEquipRadioMRMCScriptAttrRxBW | 1.3.6.1.4.1.2281.10.7.4.5.1.11 | INTEGER | read-only | The RX channel bandwidth (channel spacing) of the MRMC script. |
| INT genEquipRadioMRMCScriptAttrTxOccupiedBW | 1.3.6.1.4.1.2281.10.7.4.5.1.12 | INTEGER | read-only | The TX channel occupied bandwidth of the MRMC script. |
| INT genEquipRadioMRMCScriptAttrRxOccupiedBW | 1.3.6.1.4.1.2281.10.7.4.5.1.13 | INTEGER | read-only | The RX channel occupied bandwidth of the MRMC script. |
| RFU genEquipRadioMRMCScriptAttrLinkGrade | 1.3.6.1.4.1.2281.10.7.4.5.1.14 | RfuGrade | read-only | The link grade level that the MRMC script is designed to cope with. |
| RFU genEquipRadioMRMCScriptAttrDiffGrade | 1.3.6.1.4.1.2281.10.7.4.5.1.15 | RfuGrade | read-only | The Differential grade level that the MRMC script is designed to cope with. |
| INT genEquipRadioMRMCScriptAttrChannelBW | 1.3.6.1.4.1.2281.10.7.4.5.1.16 | INTEGER | read-only | The channel bandwidth (channel spacing) the MRMC script is designed to. |
| MRM genEquipRadioMRMCScriptAttrTxMaxProfile | 1.3.6.1.4.1.2281.10.7.4.5.1.17 | MrmcProfile | read-only | The maximum available TX profile of the MRMC script. |
| MRM genEquipRadioMRMCScriptAttrRxMaxProfile | 1.3.6.1.4.1.2281.10.7.4.5.1.18 | MrmcProfile | read-only | The maximum available RX profile of the MRMC script. |
| genEquipRadioMRMCConfigTable | 1.3.6.1.4.1.2281.10.7.4.6 | not-accessible | MRMC script configuration. | |
| genEquipRadioMRMCConfigEntry | 1.3.6.1.4.1.2281.10.7.4.6.1 | not-accessible | The configured parameters of the MRMC script. | |
| OID genEquipRadioMRMCConfigRadioId | 1.3.6.1.4.1.2281.10.7.4.6.1.1 | RadioId | read-only | The index of the MRMC Configuration Table. |
| MRM genEquipRadioMRMCConfigActiveScriptId | 1.3.6.1.4.1.2281.10.7.4.6.1.2 | MrmcScriptId | read-write | The script ID of required MRMC script. |
| MRM genEquipRadioMRMCConfigStandbyScriptId | 1.3.6.1.4.1.2281.10.7.4.6.1.3 | MrmcScriptId | read-write | The script ID which is in standby. |
| INT genEquipRadioMRMCConfigOperMode | 1.3.6.1.4.1.2281.10.7.4.6.1.4 | INTEGER | read-write | The operational mode of the MRMC script, whether it is fixed or adaptive modulation functionality. |
| MRM genEquipRadioMRMCConfigMaxProfile | 1.3.6.1.4.1.2281.10.7.4.6.1.5 | MrmcProfile | read-write | The maximum profile which is required for the MRMC script |
| MRM genEquipRadioMRMCConfigMinProfile | 1.3.6.1.4.1.2281.10.7.4.6.1.6 | MrmcProfile | read-write | The minimum profile which is required for the MRMC script |
| ENA genEquipRadioMRMCConfigAdaptivePowerAdmin | 1.3.6.1.4.1.2281.10.7.4.6.1.7 | EnableDisable | read-write | Enable or disable the adaptive power functionality during ACM operation. |
| INT genEquipRadioMRMCConfigAdaptivePowerRefClass | 1.3.6.1.4.1.2281.10.7.4.6.1.8 | INTEGER | read-write | Determines the efficiency class for the adaptive power functionality in ACM operation. |
| genEquipRadioComp | 1.3.6.1.4.1.2281.10.7.5 | |||
| genEquipRadioCompCfgTable | 1.3.6.1.4.1.2281.10.7.5.1 | not-accessible | Radio Compression table | |
| genEquipRadioCompCfgEntry | 1.3.6.1.4.1.2281.10.7.5.1.1 | not-accessible | Radio Compression table | |
| INT genEquipRadioCompMode | 1.3.6.1.4.1.2281.10.7.5.1.1.1 | INTEGER | read-write | Setting Ethernet packet header & payload compression mode. In Enhanced mode packet header can be compressed up to L4 and data compression can be activated. Legacy mode is back compatible to earlier software and hardware releases. |
| ALL genEquipRadioEnhHeaderCompAdmin | 1.3.6.1.4.1.2281.10.7.5.1.1.2 | AllowedNotAllowed | read-write | Enable/Disable Enhanced Header compression. |
| ENA genEquipRadioEnhDataCompAdmin | 1.3.6.1.4.1.2281.10.7.5.1.1.3 | EnableDisable | read-write | Enable/Disable Enhanced Data compression. |
| INT genEquipRadioEnhHeaderCompMode | 1.3.6.1.4.1.2281.10.7.5.1.1.4 | INTEGER | read-write | Setting Enhanced Header Compression depth. |
| genEquipRadioCompStatusTable | 1.3.6.1.4.1.2281.10.7.5.2 | not-accessible | Radio Compression status table. | |
| genEquipRadioCompStatusEntry | 1.3.6.1.4.1.2281.10.7.5.2.1 | not-accessible | Radio Compression status table. | |
| INT genEquipRadioCompOperationalState | 1.3.6.1.4.1.2281.10.7.5.2.1.1 | INTEGER | read-only | Current compression mode operational status. |
| genEquipRadioCompExclRulesTable | 1.3.6.1.4.1.2281.10.7.5.3 | not-accessible | Enhanced Header Compression excluding rules table. | |
| genEquipRadioCompExclRulesEntry | 1.3.6.1.4.1.2281.10.7.5.3.1 | not-accessible | Enhanced Header Compression excluding rules table. | |
| INT genEquipRadioCompExclRuleId | 1.3.6.1.4.1.2281.10.7.5.3.1.1 | INTEGER | read-only | Excluding rule number index. |
| INT genEquipRadioCompExclRuleType | 1.3.6.1.4.1.2281.10.7.5.3.1.2 | INTEGER | read-write | Add excluding rule for enhanced header compression. Excluding rule must have a number (rule-id), text description (rule-name) and excluding rule type whichcan be one of the following: VLAN Id or MAC destination address or MAC source address or Ethernet ethertype or user defined flow type. |
| STR genEquipRadioCompExclRuleName | 1.3.6.1.4.1.2281.10.7.5.3.1.3 | DisplayString | read-write | Excluding rule name. User specified. |
| OCT genEquipRadioCompExclRuleValue | 1.3.6.1.4.1.2281.10.7.5.3.1.4 | OCTET STRING | read-write | Excluding rule value. For example: MAC address or Ethertype. |
| ROW genEquipRadioCompExclRuleRowStatus | 1.3.6.1.4.1.2281.10.7.5.3.1.30 | RowStatus | read-write | Row status for this table. |
| genEquipRadioCompNG | 1.3.6.1.4.1.2281.10.7.5.4 | |||
| genEquipRadioCompNGCfgTable | 1.3.6.1.4.1.2281.10.7.5.4.1 | not-accessible | Radio Ethernet and compression config table | |
| genEquipRadioCompNGCfgEntry | 1.3.6.1.4.1.2281.10.7.5.4.1.1 | not-accessible | Radio Ethernet and compression config table entry | |
| INT genEquipRadioCompNGCfgifIndex | 1.3.6.1.4.1.2281.10.7.5.4.1.1.1 | INTEGER | read-write | Interface Index. |
| NOY genEquipRadioHeaderCompNGCfgClearStats | 1.3.6.1.4.1.2281.10.7.5.4.1.1.2 | NoYes | read-write | Clear counters on the radio port. This includes: compression counters, PTP optimized transport and cut-through counters. |
| INT genEquipRadioHeaderCompNGCfgUserFlowType | 1.3.6.1.4.1.2281.10.7.5.4.1.1.3 | INTEGER | read-write | User configured flow type for enhanced HC. This flow type is used for statistics and performance evaluation of the enhanced HC. |
| HCM genEquipRadioHeaderCompNGCfgMode | 1.3.6.1.4.1.2281.10.7.5.4.1.1.4 | HcModeType | read-write | Legacy mode is compatible for old platforms. Disabled mode disables compression. Other modes specify compression depth. |
| NOY genEquipRadioCutThroughNGCfgMode | 1.3.6.1.4.1.2281.10.7.5.4.1.1.5 | NoYes | read-write | Enable/Disable cut-through. |
| genEquipRadioCompNGExclRulesTable | 1.3.6.1.4.1.2281.10.7.5.4.2 | not-accessible | Enhanced HC excluding rules table | |
| genEquipRadioCompNGExclRulesEntry | 1.3.6.1.4.1.2281.10.7.5.4.2.1 | not-accessible | Enhanced HC excluding rules table entry | |
| INT genEquipRadioCompNGExclRulesifIndex | 1.3.6.1.4.1.2281.10.7.5.4.2.1.1 | INTEGER | read-only | Interface Index. |
| INT genEquipRadioCompNGExclRuleId | 1.3.6.1.4.1.2281.10.7.5.4.2.1.2 | INTEGER | read-only | Excluding rule number. |
| STR genEquipRadioCompNGExclRuleName | 1.3.6.1.4.1.2281.10.7.5.4.2.1.3 | DisplayString | read-only | Excluding rule name. |
| ENH genEquipRadioCompNGExclRuleType | 1.3.6.1.4.1.2281.10.7.5.4.2.1.4 | EnhancedHCExclRuleType | read-only | Excluding rule type. Possible options are: DA MAC, SA MAC, VLAN(4 bytes), Ethertype or Flow type. |
| OCT genEquipRadioCompNGExclRuleValue | 1.3.6.1.4.1.2281.10.7.5.4.2.1.5 | OCTET STRING | read-only | Excluding rule value. The value may be MAC address, VLAN(4 bytes), Ethertype(2 bytes) or Flow type(1 byte). |
| genEquipRadioCutThroughNGCountersTable | 1.3.6.1.4.1.2281.10.7.5.4.3 | not-accessible | Port counters table | |
| genEquipRadioCutThroughNGCountersEntry | 1.3.6.1.4.1.2281.10.7.5.4.3.1 | not-accessible | Port counters table entry | |
| INT genEquipRadioCutThroughNGCountersifIndex | 1.3.6.1.4.1.2281.10.7.5.4.3.1.1 | INTEGER | read-only | Interface Index. |
| C64 genEquipRadioCutThroughNGCountersRxFrames | 1.3.6.1.4.1.2281.10.7.5.4.3.1.2 | Counter64 | read-only | Counter of good cut-through bytes received. |
| C64 genEquipRadioCutThroughNGCountersRxBytes | 1.3.6.1.4.1.2281.10.7.5.4.3.1.3 | Counter64 | read-only | Counter of good cut-through bytes received. |
| C64 genEquipRadioCutThroughNGCountersTxFrames | 1.3.6.1.4.1.2281.10.7.5.4.3.1.4 | Counter64 | read-only | Counter of cut-through frames transmitted. |
| C64 genEquipRadioCutThroughNGCountersTxBytes | 1.3.6.1.4.1.2281.10.7.5.4.3.1.5 | Counter64 | read-only | Counter of cut-through bytes transmitted. |
| C64 genEquipRadioCutThroughNGCountersTotalRxFrames | 1.3.6.1.4.1.2281.10.7.5.4.3.1.6 | Counter64 | read-only | Counter of total good frames received on the port. |
| C64 genEquipRadioCutThroughNGCountersTotalRxBytes | 1.3.6.1.4.1.2281.10.7.5.4.3.1.7 | Counter64 | read-only | Counter of total good bytes received on the port. |
| C64 genEquipRadioCutThroughNGCountersTotalTxBytesOut | 1.3.6.1.4.1.2281.10.7.5.4.3.1.8 | Counter64 | read-only | Counter of total transmitted bytes. |
| C64 genEquipRadioCutThroughNGCountersTotalTxFrames | 1.3.6.1.4.1.2281.10.7.5.4.3.1.9 | Counter64 | read-only | Counter of total transmitted frames. |
| C64 genEquipRadioCutThroughNGCountersTotalTxIdleBytes | 1.3.6.1.4.1.2281.10.7.5.4.3.1.10 | Counter64 | read-only | Counter of total transmitted idle bytes. |
| C64 genEquipRadioCutThroughNGCountersTotalTxBytesIn | 1.3.6.1.4.1.2281.10.7.5.4.3.1.11 | Counter64 | read-only | Counter of total transmitted bytes. |
| genEquipRadioCompNGStatusTable | 1.3.6.1.4.1.2281.10.7.5.4.4 | not-accessible | Radio Ethernet and compression status table | |
| genEquipRadioCompNGStatusEntry | 1.3.6.1.4.1.2281.10.7.5.4.4.1 | not-accessible | Radio Ethernet and compression status table entry | |
| INT genEquipRadioCompNGStatusifindex | 1.3.6.1.4.1.2281.10.7.5.4.4.1.1 | INTEGER | read-only | Interface location. |
| HCM genEquipRadioCompNGStatusOperationalState | 1.3.6.1.4.1.2281.10.7.5.4.4.1.2 | HcModeType | read-only | Header Compression operational state. |
| HCT genEquipRadioCompNGStatusType | 1.3.6.1.4.1.2281.10.7.5.4.4.1.3 | HcType | read-only | Header Compression type. |
| genEquipRadioCompNGCountersTable | 1.3.6.1.4.1.2281.10.7.5.4.7 | not-accessible | Enhanced HC counters table | |
| genEquipRadioCompNGCountersEntry | 1.3.6.1.4.1.2281.10.7.5.4.7.1 | not-accessible | Enhanced HC counters table entry | |
| INT genEquipRadioCompNGCountersifIndex | 1.3.6.1.4.1.2281.10.7.5.4.7.1.1 | INTEGER | read-only | Interface location. |
| C64 genEquipRadioCompNGCountersHCInBytes | 1.3.6.1.4.1.2281.10.7.5.4.7.1.2 | Counter64 | read-only | Counter of bytes on the TX side before enhanced header compression. |
| C64 genEquipRadioCompNGCountersHCOutBytes | 1.3.6.1.4.1.2281.10.7.5.4.7.1.3 | Counter64 | read-only | Counter of bytes on the TX side compressed by enhanced header compression. |
| C64 genEquipRadioCompNGCountersHCCompFrm | 1.3.6.1.4.1.2281.10.7.5.4.7.1.4 | Counter64 | read-only | Counter of frames on the TX side compressed by enhanced header compression. |
| C64 genEquipRadioCompNGCountersHCFrmUncmpExclRule | 1.3.6.1.4.1.2281.10.7.5.4.7.1.5 | Counter64 | read-only | Counter of frames on the TX side not compressed by enhanced header compression due to excluding rules. |
| C64 genEquipRadioCompNGCountersHCFrmUcompInternal | 1.3.6.1.4.1.2281.10.7.5.4.7.1.6 | Counter64 | read-only | Counter of frames on the TX side not compressed by enhanced header compression due to other resons. |
| C64 genEquipRadioCompNGCountersHCLearningFrm | 1.3.6.1.4.1.2281.10.7.5.4.7.1.7 | Counter64 | read-only | Counter of learning frames transmitted by enhanced header compression. |
| C64 genEquipRadioCompNGCountersHCUserFlowTypeActiveFlows | 1.3.6.1.4.1.2281.10.7.5.4.7.1.8 | Counter64 | read-only | Number of enhanced HC active flows occupied by user selected flow type. |
| C64 genEquipRadioCompNGCountersHCTotalActiveFlows | 1.3.6.1.4.1.2281.10.7.5.4.7.1.9 | Counter64 | read-only | Number of enhanced HC active flows on the TX side. |
| genEquipRadioPtpTransport | 1.3.6.1.4.1.2281.10.7.6 | |||
| genEquipRadioPtpTransportCfgTable | 1.3.6.1.4.1.2281.10.7.6.1 | not-accessible | PTP optimized transport channel configuration table. | |
| genEquipRadioPtpTransportCfgEntry | 1.3.6.1.4.1.2281.10.7.6.1.1 | not-accessible | PTP optimized transport channel configuration table. | |
| ENA genEquipRadioPtpTransportChannelAdmin | 1.3.6.1.4.1.2281.10.7.6.1.1.1 | EnableDisable | read-write | PTP optimized transport admin. |
| INT genEquipRadioPtpTransportChannelMode | 1.3.6.1.4.1.2281.10.7.6.1.1.2 | INTEGER | read-write | PTP optimized transport operational mode. |
| genEquipRadioPtpTransportCountersTable | 1.3.6.1.4.1.2281.10.7.6.2 | not-accessible | PTP optimized transport channel counters table. | |
| genEquipRadioPtpTransportCountersEntry | 1.3.6.1.4.1.2281.10.7.6.2.1 | not-accessible | PTP optimized transport channel counters table. | |
| INT genEquipRadioPtpTransportTxFrames | 1.3.6.1.4.1.2281.10.7.6.2.1.1 | INTEGER | read-only | PTP optimized transport TX frames. |
| INT genEquipRadioPtpTransportTxDroppedFrames | 1.3.6.1.4.1.2281.10.7.6.2.1.2 | INTEGER | read-only | PTP optimized transport TX dropped frames. |
| INT genEquipRadioPtpTransportTxBytes | 1.3.6.1.4.1.2281.10.7.6.2.1.3 | INTEGER | read-only | PTP optimized transport TX bytes. |
| INT genEquipRadioPtpTransportTxDroppedBytes | 1.3.6.1.4.1.2281.10.7.6.2.1.4 | INTEGER | read-only | PTP optimized transport TX dropped bytes. |
| INT genEquipRadioPtpTransportRxFrames | 1.3.6.1.4.1.2281.10.7.6.2.1.5 | INTEGER | read-only | PTP optimized transport RX frames. |
| INT genEquipRadioPtpTransportRxBytes | 1.3.6.1.4.1.2281.10.7.6.2.1.6 | INTEGER | read-only | PTP optimized transport RX bytes. |
| genEquipRadioCutThrough | 1.3.6.1.4.1.2281.10.7.7 | |||
| genEquipRadioCutThroughCfgTable | 1.3.6.1.4.1.2281.10.7.7.1 | not-accessible | Cut through configuration table. | |
| genEquipRadioCutThroughCfgEntry | 1.3.6.1.4.1.2281.10.7.7.1.1 | not-accessible | Cut through configuration table. | |
| ENA genEquipRadioCutThroughChannelAdmin | 1.3.6.1.4.1.2281.10.7.7.1.1.1 | EnableDisable | read-write | Enable/Disable cut through mode. |
| genEquipRadioCutThroughCountersTable | 1.3.6.1.4.1.2281.10.7.7.2 | not-accessible | Cut through mode counters table. | |
| genEquipRadioCutThroughCountersEntry | 1.3.6.1.4.1.2281.10.7.7.2.1 | not-accessible | Cut through mode counters table. | |
| INT genEquipRadioCutThroughTxFrames | 1.3.6.1.4.1.2281.10.7.7.2.1.1 | INTEGER | read-only | Cut through TX frames. |
| INT genEquipRadioCutThroughTxBytes | 1.3.6.1.4.1.2281.10.7.7.2.1.2 | INTEGER | read-only | Cut through TX bytes. |
| INT genEquipRadioCutThroughRxFrames | 1.3.6.1.4.1.2281.10.7.7.2.1.3 | INTEGER | read-only | Cut through RX frames. |
| INT genEquipRadioCutThroughRxBytes | 1.3.6.1.4.1.2281.10.7.7.2.1.4 | INTEGER | read-only | Cut through RX bytes. |
| genEquipRadioGroups | 1.3.6.1.4.1.2281.10.7.8 | |||
| genEquipRadioGroupsProtection | 1.3.6.1.4.1.2281.10.7.8.1 | |||
| genEquipRadioGroupsProtectionAttrTable | 1.3.6.1.4.1.2281.10.7.8.1.1 | not-accessible | This table contains the attributes of the radio protection groups. | |
| genEquipRadioGroupsProtectionAttrEntry | 1.3.6.1.4.1.2281.10.7.8.1.1.1 | not-accessible | This table entry contains the attributes of the radio protection groups. | |
| INT genEquipRadioGroupsProtectionAttrGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.1.1.1 | INTEGER | read-only | The location of the group |
| INT genEquipRadioGroupsProtectionAttrGroupId | 1.3.6.1.4.1.2281.10.7.8.1.1.1.2 | INTEGER | read-write | The Id of the radio protection group. |
| RAD genEquipRadioGroupsProtectionAttrCommand | 1.3.6.1.4.1.2281.10.7.8.1.1.1.3 | RadioProtectionCmd | read-write | Radio protection user commands for maintenance purposes: force-switch, lockout and manual-switch. |
| OFF genEquipRadioGroupsProtectionAttrCopyToMate | 1.3.6.1.4.1.2281.10.7.8.1.1.1.4 | OffOn | read-write | Copy to mate command that copies the configuration from one radio to another in order to achieve configuration alignment. |
| INT genEquipRadioGroupsProtectionAttrCopyToMateSourceIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.1.1.5 | INTEGER | read-write | The radio location which is required to be the source of configuration for copy-to-mate command. |
| ENA genEquipRadioGroupsProtectionAttrRevertiveAdmin | 1.3.6.1.4.1.2281.10.7.8.1.1.1.6 | EnableDisable | read-write | Enable or disable revertive mode of radio protection. |
| INT genEquipRadioGroupsProtectionAttrRevertivePrimaryIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.1.1.7 | INTEGER | read-write | The radio which the system is required to revert to. |
| genEquipRadioGroupsProtectionMembersTable | 1.3.6.1.4.1.2281.10.7.8.1.2 | not-accessible | This table contains the radio protection groups members. | |
| genEquipRadioGroupsProtectionMembersEntry | 1.3.6.1.4.1.2281.10.7.8.1.2.1 | not-accessible | This table entry contains the radio protection groups members. | |
| INT genEquipRadioGroupsProtectionMembersIfIndexGroup | 1.3.6.1.4.1.2281.10.7.8.1.2.1.1 | INTEGER | read-only | The location of the radio protection group |
| INT genEquipRadioGroupsProtectionMembersGroupId | 1.3.6.1.4.1.2281.10.7.8.1.2.1.2 | INTEGER | read-only | The Id of the radio protection group. |
| INT genEquipRadioGroupsProtectionMembersMem1IfIndex | 1.3.6.1.4.1.2281.10.7.8.1.2.1.3 | INTEGER | read-write | The radio location of member 1. |
| INT genEquipRadioGroupsProtectionMembersMem2IfIndex | 1.3.6.1.4.1.2281.10.7.8.1.2.1.4 | INTEGER | read-write | The radio location of member 2. |
| ROW genEquipRadioGroupsProtectionMembersRowStatus | 1.3.6.1.4.1.2281.10.7.8.1.2.1.30 | RowStatus | read-write | Row status to allow user add entries dynamically. |
| genEquipRadioGroupsProtectionStatusTable | 1.3.6.1.4.1.2281.10.7.8.1.3 | not-accessible | This table contains the status of the radio protection. | |
| genEquipRadioGroupsProtectionStatusEntry | 1.3.6.1.4.1.2281.10.7.8.1.3.1 | not-accessible | This table entry contains the status of the radio protection. | |
| INT genEquipRadioGroupsProtectionStatusGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.3.1.1 | INTEGER | read-only | The location of the group |
| INT genEquipRadioGroupsProtectionStatusActiveIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.3.1.2 | INTEGER | read-only | The active radio location |
| INT genEquipRadioGroupsProtectionStatusStandbyIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.3.1.3 | INTEGER | read-only | The standby radio location. |
| NOY genEquipRadioGroupsProtectionStatusLockout | 1.3.6.1.4.1.2281.10.7.8.1.3.1.4 | NoYes | read-only | The radio location of member 1. |
| genEquipRadioGroupsProtectionBBSSD | 1.3.6.1.4.1.2281.10.7.8.1.10 | |||
| genEquipRadioGroupsProtectionBBSSDAttrTable | 1.3.6.1.4.1.2281.10.7.8.1.10.1 | not-accessible | This table contains the BBS-SD attributes of the radio protection groups. | |
| genEquipRadioGroupsProtectionBBSSDAttrEntry | 1.3.6.1.4.1.2281.10.7.8.1.10.1.1 | not-accessible | This table entry contains the BBS-SD attributes of the radio protection groups. | |
| INT genEquipRadioGroupsProtectionBBSSDAttrGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.1.1.1 | INTEGER | read-only | The location of the group |
| ENA genEquipRadioGroupsProtectionBBSSDAttrRevertive | 1.3.6.1.4.1.2281.10.7.8.1.10.1.1.2 | EnableDisable | read-write | Enable or disable revertive mode for BBS-SD Rx switch. |
| OFF genEquipRadioGroupsProtectionBBSSDAttrClrSwCnt | 1.3.6.1.4.1.2281.10.7.8.1.10.1.1.3 | OffOn | read-write | Clear BBS-SD Rx switch counter. |
| ENA genEquipRadioGroupsProtectionBBSSDAttrFWAuto | 1.3.6.1.4.1.2281.10.7.8.1.10.1.1.4 | EnableDisable | read-write | Enable or disable automatic Rx switching in BBS-SD. |
| genEquipRadioGroupsProtectionBBSSDStatusTable | 1.3.6.1.4.1.2281.10.7.8.1.10.2 | not-accessible | This table contains the BBS-SD status of the radio protection groups. | |
| genEquipRadioGroupsProtectionBBSSDStatusEntry | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1 | not-accessible | This table entry contains the BBS-SD status of the radio protection groups. | |
| INT genEquipRadioGroupsProtectionBBSSDStatusGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.1 | INTEGER | read-only | The location of the group |
| INT genEquipRadioGroupsProtectionBBSSDStatusAbcGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.2 | INTEGER | read-only | The attached MC-ABC group if_index. |
| INT genEquipRadioGroupsProtectionBBSSDStatusActiveRxQuality | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.3 | INTEGER | read-only | The active MC-ABC channel quality. |
| INT genEquipRadioGroupsProtectionBBSSDStatusActiveRxRadioIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.4 | INTEGER | read-only | The active rx radio if_index. |
| INT genEquipRadioGroupsProtectionBBSSDStatusActiveTxRadioIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.5 | INTEGER | read-only | The active Tx radio if_index. |
| NOY genEquipRadioGroupsProtectionBBSSDStatusLockout | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.6 | NoYes | read-only | Indicates whether the radio protection is currently in lockout. |
| INT genEquipRadioGroupsProtectionBBSSDStatusRxChId | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.7 | INTEGER | read-only | The attached MC-ABC channel ID. |
| INT genEquipRadioGroupsProtectionBBSSDStatusStdbyRxQuality | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.8 | INTEGER | read-only | The standby MC-ABC channel quality. |
| INT genEquipRadioGroupsProtectionBBSSDStatusStdbyRxRadioIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.9 | INTEGER | read-only | The standby rx radio if_index. |
| INT genEquipRadioGroupsProtectionBBSSDStatusStandbyTxRadioIfIndex | 1.3.6.1.4.1.2281.10.7.8.1.10.2.1.10 | INTEGER | read-only | The standby Tx radio if_index. |
| genEquipRadioGroupsXpic | 1.3.6.1.4.1.2281.10.7.8.2 | |||
| genEquipRadioGroupsXPICAttrTable | 1.3.6.1.4.1.2281.10.7.8.2.1 | not-accessible | This table contains the configuration of the radio XPIC groups. | |
| genEquipRadioGroupsXPICAttrEntry | 1.3.6.1.4.1.2281.10.7.8.2.1.1 | not-accessible | This table entry contains the configuration of the radio XPIC groups. | |
| INT genEquipRadioGroupsXPICAttrGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.2.1.1.1 | INTEGER | read-only | The location of the group. |
| INT genEquipRadioGroupsXPICAttrCopyToMateSourceIfIndex | 1.3.6.1.4.1.2281.10.7.8.2.1.1.2 | INTEGER | read-write | The radio location which is required to be the source of configuration for copy-to-mate command. |
| INT genEquipRadioGroupsXPICAttrGroupId | 1.3.6.1.4.1.2281.10.7.8.2.1.1.3 | INTEGER | read-write | XPIC group id. |
| ENA genEquipRadioGroupsXPICAttrXRSMAdmin | 1.3.6.1.4.1.2281.10.7.8.2.1.1.4 | EnableDisable | read-write | Administrative state of XPIC recovery state machine. |
| ENA genEquipRadioGroupsXPICAttrAdmin | 1.3.6.1.4.1.2281.10.7.8.2.1.1.5 | EnableDisable | read-write | Administrative state of XPIC. |
| COP genEquipRadioGroupsXPICAttrCopyToMate | 1.3.6.1.4.1.2281.10.7.8.2.1.1.6 | Copy2mate | read-write | User Command to resolve the mismatch between the two carriers in the XPIC group. |
| genEquipRadioGroupsXPICMembersTable | 1.3.6.1.4.1.2281.10.7.8.2.2 | not-accessible | This table contains the radio XPIC groups members. | |
| genEquipRadioGroupsXPICMembersEntry | 1.3.6.1.4.1.2281.10.7.8.2.2.1 | not-accessible | This table entry contains the radio XPIC groups members. | |
| INT genEquipRadioGroupsXPICMembersIfIndexGroup | 1.3.6.1.4.1.2281.10.7.8.2.2.1.1 | INTEGER | read-only | The location of the radio XPIC group. |
| INT genEquipRadioGroupsXPICMembersMem1IfIndex | 1.3.6.1.4.1.2281.10.7.8.2.2.1.2 | INTEGER | read-write | The radio location of member 1. |
| INT genEquipRadioGroupsXPICMembersMem2IfIndex | 1.3.6.1.4.1.2281.10.7.8.2.2.1.3 | INTEGER | read-write | The radio location of member 2. |
| ROW genEquipRadioGroupsXPICMembersRowStatus | 1.3.6.1.4.1.2281.10.7.8.2.2.1.30 | RowStatus | read-write | Row status to allow user add entries dynamically. |
| genEquipRadioGroupsXPICStatusTable | 1.3.6.1.4.1.2281.10.7.8.2.3 | not-accessible | This table contains the status of the XPIC. | |
| genEquipRadioGroupsXPICStatusEntry | 1.3.6.1.4.1.2281.10.7.8.2.3.1 | not-accessible | This table entry contains the status of the XPIC. | |
| INT genEquipRadioGroupsXPICStatusGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.2.3.1.1 | INTEGER | read-only | The location of the group |
| XPI genEquipRadioGroupsXPICStatusState | 1.3.6.1.4.1.2281.10.7.8.2.3.1.2 | XpicState | read-only | The state of XPIC State Machine |
| genEquipRadioGroupsMR | 1.3.6.1.4.1.2281.10.7.8.3 | |||
| genEquipRadioGroupsMRAttrTable | 1.3.6.1.4.1.2281.10.7.8.3.1 | not-accessible | MR config table. | |
| genEquipRadioGroupsMRAttrEntry | 1.3.6.1.4.1.2281.10.7.8.3.1.1 | not-accessible | MR config table entry. | |
| INT genEquipRadioGroupsMRAttrGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.3.1.1.1 | INTEGER | read-only | The location of the group |
| INT genEquipRadioGroupsMRAttrGroupId | 1.3.6.1.4.1.2281.10.7.8.3.1.1.2 | INTEGER | read-only | The Id of the radio MR group. |
| ENA genEquipRadioGroupsMRAttrAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.3 | EnableDisable | read-write | MR Admin. |
| INT genEquipRadioGroupsMRAttrBlockRadioIfindex | 1.3.6.1.4.1.2281.10.7.8.3.1.1.4 | INTEGER | read-write | Block Radio ifindex. |
| ENA genEquipRadioGroupsMRAttrBlockRadioAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.5 | EnableDisable | read-write | Block Radio Admin. |
| INT genEquipRadioGroupsMRAttrCopy2MateIfindex | 1.3.6.1.4.1.2281.10.7.8.3.1.1.6 | INTEGER | read-write | Copy2mate Radio ifindex. |
| ENA genEquipRadioGroupsMRAttrCopy2MateAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.7 | EnableDisable | read-write | Copy2Mate Admin. |
| ENA genEquipRadioGroupsMRAttrExBerAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.8 | EnableDisable | read-write | Excessive BER Admin. |
| INT genEquipRadioGroupsMRAttrMinNumRadio | 1.3.6.1.4.1.2281.10.7.8.3.1.1.9 | INTEGER | read-write | Minimal num of radios. |
| ENA genEquipRadioGroupsMRAttrMinProfileAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.10 | EnableDisable | read-write | Min ACM profile admin. |
| ENA genEquipRadioGroupsMRAttrSigDegardeAdmin | 1.3.6.1.4.1.2281.10.7.8.3.1.1.11 | EnableDisable | read-write | Signal Degrade Admin. |
| genEquipRadioGroupsMRMembersTable | 1.3.6.1.4.1.2281.10.7.8.3.2 | not-accessible | MR members table. | |
| genEquipRadioGroupsMRMembersEntry | 1.3.6.1.4.1.2281.10.7.8.3.2.1 | not-accessible | MR members table entry. | |
| INT genEquipRadioGroupsMRMembersIfIndexGroup | 1.3.6.1.4.1.2281.10.7.8.3.2.1.1 | INTEGER | read-only | The location of the radio MR group |
| INT genEquipRadioGroupsMRMembersMem1IfIndex | 1.3.6.1.4.1.2281.10.7.8.3.2.1.2 | INTEGER | read-write | The radio location of member 1. |
| INT genEquipRadioGroupsMRMembersMem2IfIndex | 1.3.6.1.4.1.2281.10.7.8.3.2.1.3 | INTEGER | read-write | The radio location of member 2. |
| ROW genEquipRadioGroupsMRMembersRowStatus | 1.3.6.1.4.1.2281.10.7.8.3.2.1.30 | RowStatus | read-write | Row status to allow user add entries dynamically. |
| genEquipRadioGroupsMRStatusTable | 1.3.6.1.4.1.2281.10.7.8.3.3 | not-accessible | MR Status table. | |
| genEquipRadioGroupsMRStatusEntry | 1.3.6.1.4.1.2281.10.7.8.3.3.1 | not-accessible | MR Status table entry. | |
| INT genEquipRadioGroupsMRStatusGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.3.3.1.1 | INTEGER | read-only | The location of the group |
| INT genEquipRadioGroupsMRStatusOpertionalState | 1.3.6.1.4.1.2281.10.7.8.3.3.1.2 | INTEGER | read-only | Operational State |
| INT genEquipRadioGroupsMRStatusRemoteOpertionalState | 1.3.6.1.4.1.2281.10.7.8.3.3.1.3 | INTEGER | read-only | Remote Operational State. |
| genEquipRadioGroupsMIMO | 1.3.6.1.4.1.2281.10.7.8.4 | |||
| genEquipRadioGroupsMIMOAttrTable | 1.3.6.1.4.1.2281.10.7.8.4.1 | not-accessible | The configuration table of the MIMO groups. | |
| genEquipRadioGroupsMIMOAttrEntry | 1.3.6.1.4.1.2281.10.7.8.4.1.1 | not-accessible | The configuration table of the MIMO groups entry. | |
| INT genEquipRadioGroupsMIMOAttrGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.4.1.1.1 | INTEGER | read-only | MIMO configuration table index |
| INT genEquipRadioGroupsMIMOAttrRole | 1.3.6.1.4.1.2281.10.7.8.4.1.1.2 | INTEGER | read-write | Role can be Master or Slave. |
| ENA genEquipRadioGroupsMIMOAttrAdmin | 1.3.6.1.4.1.2281.10.7.8.4.1.1.3 | EnableDisable | read-write | Administrating state of the MIMO group. |
| OFF genEquipRadioGroupsMIMOAttrResetStateMachine | 1.3.6.1.4.1.2281.10.7.8.4.1.1.4 | OffOn | read-write | Reset MIMO state machine. |
| genEquipRadioGroupsMIMOMembersTable | 1.3.6.1.4.1.2281.10.7.8.4.2 | not-accessible | The description the radio carrier members of the MIMO groups. | |
| genEquipRadioGroupsMIMOMembersEntry | 1.3.6.1.4.1.2281.10.7.8.4.2.1 | not-accessible | The description the radio carrier members of the MIMO groups entry. | |
| INT genEquipRadioGroupsMIMOMembersGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.4.2.1.1 | INTEGER | read-only | MIMO members table index |
| INT genEquipRadioGroupsMIMOMembersGroupType | 1.3.6.1.4.1.2281.10.7.8.4.2.1.2 | INTEGER | read-write | Type of MIMO group: 2x2 or 4x4 etc... |
| INT genEquipRadioGroupsMIMOMembersMem1IfIndex | 1.3.6.1.4.1.2281.10.7.8.4.2.1.3 | INTEGER | read-write | The radio location of member 1. |
| INT genEquipRadioGroupsMIMOMembersMem2IfIndex | 1.3.6.1.4.1.2281.10.7.8.4.2.1.4 | INTEGER | read-write | The radio location of member 2. |
| INT genEquipRadioGroupsMIMOMembersMem3IfIndex | 1.3.6.1.4.1.2281.10.7.8.4.2.1.5 | INTEGER | read-write | The radio location of member 3. |
| INT genEquipRadioGroupsMIMOMembersMem4IfIndex | 1.3.6.1.4.1.2281.10.7.8.4.2.1.6 | INTEGER | read-write | The radio location of member 4. |
| ROW genEquipRadioGroupsMIMOMembersRowStatus | 1.3.6.1.4.1.2281.10.7.8.4.2.1.30 | RowStatus | read-write | Row status to allow user add entries dynamically. |
| genEquipRadioGroupsMIMOStatusTable | 1.3.6.1.4.1.2281.10.7.8.4.3 | not-accessible | The current status table of the MIMO groups. | |
| genEquipRadioGroupsMIMOStatusEntry | 1.3.6.1.4.1.2281.10.7.8.4.3.1 | not-accessible | The current status table of the MIMO groups entry. | |
| INT genEquipRadioGroupsMIMOStatusGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.4.3.1.1 | INTEGER | read-only | MIMO status table index |
| INT genEquipRadioGroupsMIMOStatusState | 1.3.6.1.4.1.2281.10.7.8.4.3.1.2 | INTEGER | read-only | MIMO-State |
| INT genEquipRadioGroupsMIMOStatus1stMMI | 1.3.6.1.4.1.2281.10.7.8.4.3.1.3 | INTEGER | read-only | MIMO interference in dB of the 1st carrier. |
| INT genEquipRadioGroupsMIMOStatus2ndMMI | 1.3.6.1.4.1.2281.10.7.8.4.3.1.4 | INTEGER | read-only | MIMO interference in dB of the 2nd carrier. |
| INT genEquipRadioGroupsMIMOStatus3rdMMI | 1.3.6.1.4.1.2281.10.7.8.4.3.1.5 | INTEGER | read-only | MIMO interference in dB of the 3rd carrier. |
| INT genEquipRadioGroupsMIMOStatus4thMMI | 1.3.6.1.4.1.2281.10.7.8.4.3.1.6 | INTEGER | read-only | MIMO interference in dB of the 4th carrier. |
| INT genEquipRadioGroupsMIMOStatusAdvancedState | 1.3.6.1.4.1.2281.10.7.8.4.3.1.7 | INTEGER | read-only | MIMO advanced state. |
| genEquipRadioGroupsAbc | 1.3.6.1.4.1.2281.10.7.8.5 | |||
| genEquipRadioGroupsAbcAttrTable | 1.3.6.1.4.1.2281.10.7.8.5.1 | not-accessible | Multi Carrier ABC configuration table. | |
| genEquipRadioGroupsAbcAttrEntry | 1.3.6.1.4.1.2281.10.7.8.5.1.1 | not-accessible | Multi Carrier ABC configuration table. | |
| INT genEquipRadioGroupsAbcAttrIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.1.1.1 | INTEGER | read-only | The interface-index of the ABC group |
| STR genEquipRadioGroupsAbcAttrGroupName | 1.3.6.1.4.1.2281.10.7.8.5.1.1.2 | DisplayString | read-write | Textual description of the ABC group. |
| ENA genEquipRadioGroupsAbcAttrAdminState | 1.3.6.1.4.1.2281.10.7.8.5.1.1.3 | EnableDisable | read-write | The Administrative state of ABC radio group which decides if the Multi Carrier ABC group is enabled or disabled. |
| INT genEquipRadioGroupsAbcAttrQnumberOfRadioMembers | 1.3.6.1.4.1.2281.10.7.8.5.1.1.4 | INTEGER | read-write | The number of radios that can be members of the Multi Carrier ABC group. |
| ENA genEquipRadioGroupsAbcAttrProtectionEnable | 1.3.6.1.4.1.2281.10.7.8.5.1.1.5 | EnableDisable | read-write | When Protection is Enabled protecion groups can be added to the Multi-carrier ABC group. When disabled regular channels can be attached. |
| INT genEquipRadioGroupsAbcAttrHighPriEthernetBandwidth | 1.3.6.1.4.1.2281.10.7.8.5.1.1.6 | INTEGER | read-write | Bandwidth reserved for high priority ethernet in Kbps. Values range from from 0 (i.e. No high pri ethernet) to max capacity (I.e. no STM-1s) in Kbps. |
| INT genEquipRadioGroupsAbcAttrQualityThreshold | 1.3.6.1.4.1.2281.10.7.8.5.1.1.7 | INTEGER | read-write | Members degrading below this threshold will be set to 'do not use' in the group. |
| ROW genEquipRadioGroupsAbcAttrRowStatus | 1.3.6.1.4.1.2281.10.7.8.5.1.1.30 | RowStatus | read-write | This is the row status. |
| genEquipRadioGroupsAbcMembersTable | 1.3.6.1.4.1.2281.10.7.8.5.2 | not-accessible | Multi Carrier ABC members table. | |
| genEquipRadioGroupsAbcMembersEntry | 1.3.6.1.4.1.2281.10.7.8.5.2.1 | not-accessible | Multi Carrier ABC members table entry. | |
| INT genEquipRadioGroupsAbcMembersGroupIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.1 | INTEGER | read-only | Integer representing the group interface ifindex |
| INT genEquipRadioGroupsAbcMembersGroupId | 1.3.6.1.4.1.2281.10.7.8.5.2.1.2 | INTEGER | read-only | Integer representing the group interface ID. |
| INT genEquipRadioGroupsAbcMembersChannel1MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.3 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel1adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.4 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel2MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.5 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel2adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.6 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel3MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.7 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel3adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.8 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel4MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.9 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel4adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.10 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel5MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.11 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel5adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.12 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel6MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.13 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel6adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.14 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel7MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.15 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel7adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.16 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| INT genEquipRadioGroupsAbcMembersChannel8MemberIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.2.1.17 | INTEGER | read-write | IfIndex representing the group member connect to this ABC channel. |
| ENA genEquipRadioGroupsAbcMembersChannel8adminState | 1.3.6.1.4.1.2281.10.7.8.5.2.1.18 | EnableDisable | read-write | The Administrative state of an ABC channel. |
| genEquipRadioGroupsAbcStatusTable | 1.3.6.1.4.1.2281.10.7.8.5.3 | not-accessible | Multi Carrier ABC status table. | |
| genEquipRadioGroupsAbcStatusEntry | 1.3.6.1.4.1.2281.10.7.8.5.3.1 | not-accessible | Multi Carrier ABC status table entry. | |
| INT genEquipRadioGroupsAbcStatusIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.3.1.1 | INTEGER | read-only | The interface-index of the ABC group |
| DOW genEquipRadioGroupsAbcStatusOperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.2 | DownUp | read-only | The operational state of the ABC group as a WAN. |
| DOW genEquipRadioGroupsAbcStatusRemoteOperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.3 | DownUp | read-only | The remote ABC groups operational state. |
| INT genEquipRadioGroupsAbcStatusCurrentAggregatedCapacityRX | 1.3.6.1.4.1.2281.10.7.8.5.3.1.4 | INTEGER | read-only | The combined current RX throughput capacity of the ABC group in Kbps. |
| INT genEquipRadioGroupsAbcStatusCurrentAggregatedCapacityTX | 1.3.6.1.4.1.2281.10.7.8.5.3.1.5 | INTEGER | read-only | The combined current TX throughput capacity of the ABC group in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel1Operstate | 1.3.6.1.4.1.2281.10.7.8.5.3.1.6 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel1Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.7 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel2Operstate | 1.3.6.1.4.1.2281.10.7.8.5.3.1.8 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel2Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.9 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel3OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.10 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel3Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.11 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel4OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.12 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel4Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.13 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel5OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.14 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel5Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.15 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel6OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.16 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel6Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.17 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel7OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.18 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel7Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.19 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| DOW genEquipRadioGroupsAbcStatusChannel8OperState | 1.3.6.1.4.1.2281.10.7.8.5.3.1.20 | DownUp | read-only | The operational state of the ABC channel. |
| INT genEquipRadioGroupsAbcStatusChannel8Capacity | 1.3.6.1.4.1.2281.10.7.8.5.3.1.21 | INTEGER | read-only | The current throughput capacity of the ABC channel in Kbps. |
| genEquipStm1AbcAttrTable | 1.3.6.1.4.1.2281.10.7.8.5.5 | not-accessible | Multi Carrier ABC stm1 table. | |
| genEquipStm1AbcAttrEntry | 1.3.6.1.4.1.2281.10.7.8.5.5.1 | not-accessible | Multi Carrier ABC stm1 table entry. | |
| INT genEquipStm1AbcAttrIfIndex | 1.3.6.1.4.1.2281.10.7.8.5.5.1.1 | INTEGER | read-only | The interface-index of the ABC group |
| INT genEquipStm1AbcAttrGroupId | 1.3.6.1.4.1.2281.10.7.8.5.5.1.2 | INTEGER | read-only | Integer representing the group interface ID. |
| INT genEquipStm1AbcAttrNumberOfMembers | 1.3.6.1.4.1.2281.10.7.8.5.5.1.3 | INTEGER | read-write | The number of STM-1/OC-3 channels that can be members of the Multi Carrier ABC group. |
| INT genEquipStm1AbcAttrPri1IfIndex | 1.3.6.1.4.1.2281.10.7.8.5.5.1.4 | INTEGER | read-write | Location of the highest priority STM-1/OC-3 interface. |
| INT genEquipStm1AbcAttrPri2IfIndex | 1.3.6.1.4.1.2281.10.7.8.5.5.1.5 | INTEGER | read-write | Location of the highest priority STM-1/OC-3 interface. |
| INT genEquipStm1AbcAttrPri3IfIndex | 1.3.6.1.4.1.2281.10.7.8.5.5.1.6 | INTEGER | read-write | Location of the highest priority STM-1/OC-3 interface. |
| INT genEquipStm1AbcAttrPri4IfIndex | 1.3.6.1.4.1.2281.10.7.8.5.5.1.7 | INTEGER | read-write | Location of the highest priority STM-1/OC-3 interface. |
RFC description
Manages radio resource configuration on Motorola wireless devices, covering channel allocation, power levels, and RF parameters.
Start monitoring Microwave radio point-to-point backhaul units with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.