All MIBs › ME1200-DHCP-SERVER-MIB
Organization: Cisco Systems, Inc
Last Updated: 2014-03-11
Category: Protocol: DHCP, Vendor: Cisco
Description: Cisco ME1200 Metro Ethernet switch MIB defining integrated DHCP server pool, lease, and binding management objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ME1200-DHCP-SERVER-MIB?
ME1200-DHCP-SERVER-MIB is a Cisco private MIB for the ME1200 Metro Ethernet switch family that models an integrated DHCP server function running on the switch itself. It exposes configuration-category data covering global DHCP server admin mode, per-VLAN DHCP enable/disable settings, and excluded IP address ranges reserved from dynamic assignment. Because it governs a software service embedded in the switch rather than hardware sensors, it is primarily used to monitor DHCP service status and configuration correctness, confirming the server is enabled where expected and that exclusion pools match intended static-address reservations. It is a self-contained private MIB but ties its VLAN entries to the standard ifIndex convention used across IF-MIB and other Cisco interface MIBs. It is typically deployed in metro access/aggregation networks where the ME1200 switch itself provides DHCP addressing to subscriber VLANs without a separate DHCP server, and administrators can open an ME1200-DHCP-SERVER-MIB MIB Browser session to confirm the exclusion and per-VLAN configuration objects.
IPNetwork Monitor allows you to monitor SNMP objects defined in ME1200-DHCP-SERVER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco ME1200 Metro Ethernet switch
Monitoring Examples
An administrator would poll me1200DhcpServerConfigGlobalsMode to confirm the DHCP server is globally enabled, then walk me1200DhcpServerConfigVlanTable indexed by me1200DhcpServerConfigVlanIfIndex to check per-VLAN mode. Reviewing me1200DhcpServerConfigExcludedTable entries (low/high IP addresses) verifies configured exclusion ranges match intended static-assignment pools. A mismatch here would mean the DHCP server could hand out addresses meant to be reserved for static devices.
What Can Be Monitored
- DHCP server global admin mode
- per-VLAN DHCP server mode
- excluded IP address ranges
- VLAN interface index mapping
- excluded-range row status
This MIB depends on
Related MIBs
Imported Objects
From CISCOME1200-MIB
| me1200SwitchMgmt | OBJECT-IDENTITY |
From ME1200-TC
| ME1200DisplayString | |
| ME1200InterfaceIndex | |
| ME1200RowEditorState | |
| ME1200Unsigned16 |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| me1200DhcpServerMIB | 1.3.6.1.4.1.9.9.815.1.109 | This is a private version of DhcpServer | ||
| me1200DhcpServerMIBObjects | 1.3.6.1.4.1.9.9.815.1.109.1 | |||
| me1200DhcpServerConfig | 1.3.6.1.4.1.9.9.815.1.109.1.2 | |||
| me1200DhcpServerConfigGlobals | 1.3.6.1.4.1.9.9.815.1.109.1.2.1 | |||
| T/F me1200DhcpServerConfigGlobalsMode | 1.3.6.1.4.1.9.9.815.1.109.1.2.1.1 | TruthValue | read-write | Global mode of DHCP server. true(1) is to enable the functions of DHCP server and false(2) is to disable it. |
| me1200DhcpServerConfigVlanTable | 1.3.6.1.4.1.9.9.815.1.109.1.2.2 | not-accessible | This is the table of DHCP server VLAN configuration. The index is VLAN ID. | |
| me1200DhcpServerConfigVlanEntry | 1.3.6.1.4.1.9.9.815.1.109.1.2.2.1 | not-accessible | Each VLAN has a set of parameters | |
| NUM me1200DhcpServerConfigVlanIfIndex | 1.3.6.1.4.1.9.9.815.1.109.1.2.2.1.1 | ME1200InterfaceIndex | not-accessible | Logical interface number of VLAN. |
| T/F me1200DhcpServerConfigVlanMode | 1.3.6.1.4.1.9.9.815.1.109.1.2.2.1.2 | TruthValue | read-write | VLAN mode of DHCP server. true(1) is to enable DHCP server per VLAN and false(2) is to disable it per VLAN. |
| me1200DhcpServerConfigExcludedTable | 1.3.6.1.4.1.9.9.815.1.109.1.2.3 | not-accessible | The table is DHCP server excluded IP onfiguration table. The indexes are low IP and high IP address. | |
| me1200DhcpServerConfigExcludedEntry | 1.3.6.1.4.1.9.9.815.1.109.1.2.3.1 | not-accessible | Each entry has a set of parameters | |
| IP me1200DhcpServerConfigExcludedLowIpAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.3.1.1 | IpAddress | not-accessible | Low IP address. |
| IP me1200DhcpServerConfigExcludedHighIpAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.3.1.2 | IpAddress | not-accessible | High IP address. |
| ME1 me1200DhcpServerConfigExcludedAction | 1.3.6.1.4.1.9.9.815.1.109.1.2.3.1.100 | ME1200RowEditorState | read-write | Action |
| me1200DhcpServerConfigExcludedIpTableRowEditor | 1.3.6.1.4.1.9.9.815.1.109.1.2.4 | |||
| IP me1200DhcpServerConfigExcludedIpTableRowEditorLowIpAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.4.1 | IpAddress | read-write | Low IP address. |
| IP me1200DhcpServerConfigExcludedIpTableRowEditorHighIpAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.4.2 | IpAddress | read-write | High IP address. |
| ME1 me1200DhcpServerConfigExcludedIpTableRowEditorAction | 1.3.6.1.4.1.9.9.815.1.109.1.2.4.100 | ME1200RowEditorState | read-write | Action |
| me1200DhcpServerConfigPoolTable | 1.3.6.1.4.1.9.9.815.1.109.1.2.5 | not-accessible | The table is DHCP server pool onfiguration table. The indexe is pool name. | |
| me1200DhcpServerConfigPoolEntry | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1 | not-accessible | Each entry has a set of parameters | |
| STR me1200DhcpServerConfigPoolPoolName | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.1 | ME1200DisplayString | not-accessible | Name of DHCP pool. |
| ME1 me1200DhcpServerConfigPoolPoolType | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.2 | ME1200PoolType | read-write | Type of pool. none(0) means the pool type is not defined yet. network(1) means the pool defines a pool of IP addresses to service more than one DHCP client. host(2) means the pool services for a specific DHCP client identified by client identifier or hardware address. |
| IP me1200DhcpServerConfigPoolIpv4Address | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.3 | IpAddress | read-write | Network number of the subnet. If the pool type is of network, the IP address can be any general IP address. If the pool type is of host, the IP address must be a unicast IP address. |
| IP me1200DhcpServerConfigPoolSubnetMask | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.4 | IpAddress | read-write | Subnet Mask. DHCP option 1. Specify subnet mask of the DHCP address pool, excluding 0.0.0.0 and 255.255.255.255. |
| IP me1200DhcpServerConfigPoolSubnetBroadcast | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.5 | IpAddress | read-write | Broadcast IP address in the subnet. DHCP option 28. Specify the broadcast address in use on the client's subnet. |
| U32 me1200DhcpServerConfigPoolLeaseDay | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.6 | Unsigned32 | read-write | Number of days of lease time. DHCP option 51, 58 and 59. The value range is 0-365. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| U32 me1200DhcpServerConfigPoolLeaseHour | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.7 | Unsigned32 | read-write | Number of hours of lease time. DHCP option 51, 58 and 59. The value range is 0-23. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| U32 me1200DhcpServerConfigPoolLeaseMinute | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.8 | Unsigned32 | read-write | Number of minutes of lease time. DHCP option 51, 58 and 59. The value range is 0-59. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| STR me1200DhcpServerConfigPoolDomainName | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.9 | ME1200DisplayString | read-write | Domain name. DHCP option 15. Specify domain name that client should use when resolving hostname via DNS. |
| IP me1200DhcpServerConfigPoolDefaultRouter1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.10 | IpAddress | read-write | Default router 1. |
| IP me1200DhcpServerConfigPoolDefaultRouter2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.11 | IpAddress | read-write | Default router 2. |
| IP me1200DhcpServerConfigPoolDefaultRouter3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.12 | IpAddress | read-write | Default router 3. |
| IP me1200DhcpServerConfigPoolDefaultRouter4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.13 | IpAddress | read-write | Default router 4. |
| IP me1200DhcpServerConfigPoolDnsServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.14 | IpAddress | read-write | DNS server 1. |
| IP me1200DhcpServerConfigPoolDnsServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.15 | IpAddress | read-write | DNS server 2. |
| IP me1200DhcpServerConfigPoolDnsServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.16 | IpAddress | read-write | DNS server 3. |
| IP me1200DhcpServerConfigPoolDnsServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.17 | IpAddress | read-write | DNS server 4. |
| IP me1200DhcpServerConfigPoolNtpServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.18 | IpAddress | read-write | NTP server 1. |
| IP me1200DhcpServerConfigPoolNtpServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.19 | IpAddress | read-write | NTP server 2. |
| IP me1200DhcpServerConfigPoolNtpServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.20 | IpAddress | read-write | NTP server 3. |
| IP me1200DhcpServerConfigPoolNtpServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.21 | IpAddress | read-write | NTP server 4. |
| ME1 me1200DhcpServerConfigPoolNetbiosNodeType | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.22 | ME1200NetbiosNodeType | read-write | Type of NetBIOS node. DHCP option 46. Specify NetBIOS node type option to allow Netbios over TCP/IP clients which are configurable to be configured as described in RFC 1001/1002. nodeNone(0) means the node type is not defined yet. nodeB(1) means the node type is type of B. nodeP(2) means the node type is type of P. nodeM(3) means the node type is type of M. nodeH(4) means the node type is type of H. |
| STR me1200DhcpServerConfigPoolNetbiosScope | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.23 | ME1200DisplayString | read-write | NetBIOS scope. DHCP option 47. Specify the NetBIOS over TCP/IP scope parameter for the client as specified in RFC 1001/1002. |
| IP me1200DhcpServerConfigPoolNetbiosNameServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.24 | IpAddress | read-write | NetBIOS name server 1. |
| IP me1200DhcpServerConfigPoolNetbiosNameServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.25 | IpAddress | read-write | NetBIOS name server 2. |
| IP me1200DhcpServerConfigPoolNetbiosNameServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.26 | IpAddress | read-write | NetBIOS name server 3. |
| IP me1200DhcpServerConfigPoolNetbiosNameServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.27 | IpAddress | read-write | NetBIOS name server 4. |
| STR me1200DhcpServerConfigPoolNisDomainName | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.28 | ME1200DisplayString | read-write | NIS Domain Name. DHCP option 40. Specify the name of the client's NIS domain. |
| IP me1200DhcpServerConfigPoolNisServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.29 | IpAddress | read-write | NIS server 1. |
| IP me1200DhcpServerConfigPoolNisServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.30 | IpAddress | read-write | NIS server 2. |
| IP me1200DhcpServerConfigPoolNisServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.31 | IpAddress | read-write | NIS server 3. |
| IP me1200DhcpServerConfigPoolNisServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.32 | IpAddress | read-write | NIS server 4. |
| OID me1200DhcpServerConfigPoolClientIdentifierType | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.33 | ME1200ClientIdentifierType | read-write | Type of client identifier. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. none(0) means the client identifier type is not defined yet. fqdn(1) means the client identifier type is type of FQDN (Fully Qualified Domain Name). mac(2) means the client identifier type is type of MAC address. |
| STR me1200DhcpServerConfigPoolClientIdentifierFqdn | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.34 | ME1200DisplayString | read-write | Client's Fully Qualified Domain Name. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. This takes effect only if ClientIdentifierType is defined fqdn(1). |
| MAC me1200DhcpServerConfigPoolClientIdentifierMac | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.35 | MacAddress | read-write | Client's MAC address. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. This takes effect only if ClientIdentifierType is defined as mac(2). |
| MAC me1200DhcpServerConfigPoolClientHardwareAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.36 | MacAddress | read-write | Client's hardware address. Specify client's hardware(MAC) address to be used when the pool is the type of host. |
| STR me1200DhcpServerConfigPoolClientName | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.37 | ME1200DisplayString | read-write | Client name. DHCP option 12. Specify the name of client to be used when the pool is the type of host. |
| STR me1200DhcpServerConfigPoolVendorClassId1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.38 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolVendorSpecificInfo1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.39 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolVendorClassId2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.40 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolVendorSpecificInfo2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.41 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolVendorClassId3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.42 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolVendorSpecificInfo3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.43 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolVendorClassId4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.44 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolVendorSpecificInfo4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.45 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| ME1 me1200DhcpServerConfigPoolAction | 1.3.6.1.4.1.9.9.815.1.109.1.2.5.1.100 | ME1200RowEditorState | read-write | Action |
| me1200DhcpServerConfigPoolTableRowEditor | 1.3.6.1.4.1.9.9.815.1.109.1.2.6 | |||
| STR me1200DhcpServerConfigPoolTableRowEditorPoolName | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.1 | ME1200DisplayString | read-write | Name of DHCP pool. |
| ME1 me1200DhcpServerConfigPoolTableRowEditorPoolType | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.2 | ME1200PoolType | read-write | Type of pool. none(0) means the pool type is not defined yet. network(1) means the pool defines a pool of IP addresses to service more than one DHCP client. host(2) means the pool services for a specific DHCP client identified by client identifier or hardware address. |
| IP me1200DhcpServerConfigPoolTableRowEditorIpv4Address | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.3 | IpAddress | read-write | Network number of the subnet. If the pool type is of network, the IP address can be any general IP address. If the pool type is of host, the IP address must be a unicast IP address. |
| IP me1200DhcpServerConfigPoolTableRowEditorSubnetMask | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.4 | IpAddress | read-write | Subnet Mask. DHCP option 1. Specify subnet mask of the DHCP address pool, excluding 0.0.0.0 and 255.255.255.255. |
| IP me1200DhcpServerConfigPoolTableRowEditorSubnetBroadcast | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.5 | IpAddress | read-write | Broadcast IP address in the subnet. DHCP option 28. Specify the broadcast address in use on the client's subnet. |
| U32 me1200DhcpServerConfigPoolTableRowEditorLeaseDay | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.6 | Unsigned32 | read-write | Number of days of lease time. DHCP option 51, 58 and 59. The value range is 0-365. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| U32 me1200DhcpServerConfigPoolTableRowEditorLeaseHour | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.7 | Unsigned32 | read-write | Number of hours of lease time. DHCP option 51, 58 and 59. The value range is 0-23. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| U32 me1200DhcpServerConfigPoolTableRowEditorLeaseMinute | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.8 | Unsigned32 | read-write | Number of minutes of lease time. DHCP option 51, 58 and 59. The value range is 0-59. Specify lease time that allows the client to request a lease time for the IP address. If all of LeaseDay, LeaseHour and LeaseMinute are 0's, then it means the lease time is infinite. |
| STR me1200DhcpServerConfigPoolTableRowEditorDomainName | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.9 | ME1200DisplayString | read-write | Domain name. DHCP option 15. Specify domain name that client should use when resolving hostname via DNS. |
| IP me1200DhcpServerConfigPoolTableRowEditorDefaultRouter1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.10 | IpAddress | read-write | Default router 1. |
| IP me1200DhcpServerConfigPoolTableRowEditorDefaultRouter2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.11 | IpAddress | read-write | Default router 2. |
| IP me1200DhcpServerConfigPoolTableRowEditorDefaultRouter3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.12 | IpAddress | read-write | Default router 3. |
| IP me1200DhcpServerConfigPoolTableRowEditorDefaultRouter4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.13 | IpAddress | read-write | Default router 4. |
| IP me1200DhcpServerConfigPoolTableRowEditorDnsServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.14 | IpAddress | read-write | DNS server 1. |
| IP me1200DhcpServerConfigPoolTableRowEditorDnsServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.15 | IpAddress | read-write | DNS server 2. |
| IP me1200DhcpServerConfigPoolTableRowEditorDnsServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.16 | IpAddress | read-write | DNS server 3. |
| IP me1200DhcpServerConfigPoolTableRowEditorDnsServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.17 | IpAddress | read-write | DNS server 4. |
| IP me1200DhcpServerConfigPoolTableRowEditorNtpServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.18 | IpAddress | read-write | NTP server 1. |
| IP me1200DhcpServerConfigPoolTableRowEditorNtpServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.19 | IpAddress | read-write | NTP server 2. |
| IP me1200DhcpServerConfigPoolTableRowEditorNtpServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.20 | IpAddress | read-write | NTP server 3. |
| IP me1200DhcpServerConfigPoolTableRowEditorNtpServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.21 | IpAddress | read-write | NTP server 4. |
| ME1 me1200DhcpServerConfigPoolTableRowEditorNetbiosNodeType | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.22 | ME1200NetbiosNodeType | read-write | Type of NetBIOS node. DHCP option 46. Specify NetBIOS node type option to allow Netbios over TCP/IP clients which are configurable to be configured as described in RFC 1001/1002. nodeNone(0) means the node type is not defined yet. nodeB(1) means the node type is type of B. nodeP(2) means the node type is type of P. nodeM(3) means the node type is type of M. nodeH(4) means the node type is type of H. |
| STR me1200DhcpServerConfigPoolTableRowEditorNetbiosScope | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.23 | ME1200DisplayString | read-write | NetBIOS scope. DHCP option 47. Specify the NetBIOS over TCP/IP scope parameter for the client as specified in RFC 1001/1002. |
| IP me1200DhcpServerConfigPoolTableRowEditorNetbiosNameServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.24 | IpAddress | read-write | NetBIOS name server 1. |
| IP me1200DhcpServerConfigPoolTableRowEditorNetbiosNameServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.25 | IpAddress | read-write | NetBIOS name server 2. |
| IP me1200DhcpServerConfigPoolTableRowEditorNetbiosNameServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.26 | IpAddress | read-write | NetBIOS name server 3. |
| IP me1200DhcpServerConfigPoolTableRowEditorNetbiosNameServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.27 | IpAddress | read-write | NetBIOS name server 4. |
| STR me1200DhcpServerConfigPoolTableRowEditorNisDomainName | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.28 | ME1200DisplayString | read-write | NIS Domain Name. DHCP option 40. Specify the name of the client's NIS domain. |
| IP me1200DhcpServerConfigPoolTableRowEditorNisServer1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.29 | IpAddress | read-write | NIS server 1. |
| IP me1200DhcpServerConfigPoolTableRowEditorNisServer2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.30 | IpAddress | read-write | NIS server 2. |
| IP me1200DhcpServerConfigPoolTableRowEditorNisServer3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.31 | IpAddress | read-write | NIS server 3. |
| IP me1200DhcpServerConfigPoolTableRowEditorNisServer4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.32 | IpAddress | read-write | NIS server 4. |
| OID me1200DhcpServerConfigPoolTableRowEditorClientIdentifierType | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.33 | ME1200ClientIdentifierType | read-write | Type of client identifier. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. none(0) means the client identifier type is not defined yet. fqdn(1) means the client identifier type is type of FQDN (Fully Qualified Domain Name). mac(2) means the client identifier type is type of MAC address. |
| STR me1200DhcpServerConfigPoolTableRowEditorClientIdentifierFqdn | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.34 | ME1200DisplayString | read-write | Client's Fully Qualified Domain Name. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. This takes effect only if ClientIdentifierType is defined fqdn(1). |
| MAC me1200DhcpServerConfigPoolTableRowEditorClientIdentifierMac | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.35 | MacAddress | read-write | Client's MAC address. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. This takes effect only if ClientIdentifierType is defined as mac(2). |
| MAC me1200DhcpServerConfigPoolTableRowEditorClientHardwareAddress | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.36 | MacAddress | read-write | Client's hardware address. Specify client's hardware(MAC) address to be used when the pool is the type of host. |
| STR me1200DhcpServerConfigPoolTableRowEditorClientName | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.37 | ME1200DisplayString | read-write | Client name. DHCP option 12. Specify the name of client to be used when the pool is the type of host. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorClassId1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.38 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorSpecificInfo1 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.39 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorClassId2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.40 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorSpecificInfo2 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.41 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorClassId3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.42 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorSpecificInfo3 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.43 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorClassId4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.44 | ME1200DisplayString | read-write | Vendor Class Identifier. DHCP option 60. Specify to be used by DHCP client to optionally identify the vendor type and configuration of a DHCP client. DHCP server will deliver the corresponding option 43 specific information to the client that sends option 60 vendor class identifier. |
| STR me1200DhcpServerConfigPoolTableRowEditorVendorSpecificInfo4 | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.45 | ME1200DisplayString | read-write | Vendor Specific Information. DHCP option 43. Specify vendor specific information corresponding to option 60 vendor class identifier. Therefore, the corresponding vendor class identifier must be defined before this specific information. |
| ME1 me1200DhcpServerConfigPoolTableRowEditorAction | 1.3.6.1.4.1.9.9.815.1.109.1.2.6.100 | ME1200RowEditorState | read-write | Action |
| me1200DhcpServerStatus | 1.3.6.1.4.1.9.9.815.1.109.1.3 | |||
| me1200DhcpServerStatusDeclinedTable | 1.3.6.1.4.1.9.9.815.1.109.1.3.1 | not-accessible | This is a table of IP addresses declined by DHCP client. | |
| me1200DhcpServerStatusDeclinedEntry | 1.3.6.1.4.1.9.9.815.1.109.1.3.1.1 | not-accessible | Each entry has a declined IP address. | |
| I32 me1200DhcpServerStatusDeclinedEntryNo | 1.3.6.1.4.1.9.9.815.1.109.1.3.1.1.1 | Integer32 | not-accessible | The number of entry. The number starts from 1. |
| IP me1200DhcpServerStatusDeclinedIpv4Address | 1.3.6.1.4.1.9.9.815.1.109.1.3.1.1.2 | IpAddress | read-only | IPv4 address declined by DHCP client. |
| me1200DhcpServerStatusStatistics | 1.3.6.1.4.1.9.9.815.1.109.1.3.2 | |||
| U32 me1200DhcpServerStatusStatisticsDiscoverCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.1 | Unsigned32 | read-only | Number of DHCP DISCOVER messages received. |
| U32 me1200DhcpServerStatusStatisticsOfferCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.2 | Unsigned32 | read-only | Number of DHCP OFFER messages sent. |
| U32 me1200DhcpServerStatusStatisticsRequestCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.3 | Unsigned32 | read-only | Number of DHCP REQUEST messages received. |
| U32 me1200DhcpServerStatusStatisticsAckCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.4 | Unsigned32 | read-only | Number of DHCP ACK messages sent. |
| U32 me1200DhcpServerStatusStatisticsNakCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.5 | Unsigned32 | read-only | Number of DHCP NAK messages sent. |
| U32 me1200DhcpServerStatusStatisticsDeclineCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.6 | Unsigned32 | read-only | Number of DHCP DECLINE messages received. |
| U32 me1200DhcpServerStatusStatisticsReleaseCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.7 | Unsigned32 | read-only | Number of DHCP RELEASE messages received. |
| U32 me1200DhcpServerStatusStatisticsInformCnt | 1.3.6.1.4.1.9.9.815.1.109.1.3.2.8 | Unsigned32 | read-only | Number of DHCP INFORM messages received. |
| me1200DhcpServerStatusBindingTable | 1.3.6.1.4.1.9.9.815.1.109.1.3.3 | not-accessible | This is a table of binding data. | |
| me1200DhcpServerStatusBindingEntry | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1 | not-accessible | Each entry has the binding data. | |
| IP me1200DhcpServerStatusBindingIpAddress | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.1 | IpAddress | not-accessible | IP address. |
| ME1 me1200DhcpServerStatusBindingState | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.2 | ME1200BindingState | read-only | State of binding. none(0) means the binding is not in use. allocated(1) means the binding is allocated to the new DHCP client who send DHCPDISCOVER. committed(2) means the binding is committed as the DHCP process is completed successfully. expired(3) means the lease of the binding expired. |
| ME1 me1200DhcpServerStatusBindingType | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.3 | ME1200BindingType | read-only | Type of binding. none(0) means the binding is not in use. automatic(1) means the binding is mapped to network-type pool. manual(2) means the binding is mapped to host-type pool. expired(3) means the lease of the binding expired. |
| STR me1200DhcpServerStatusBindingPoolName | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.4 | ME1200DisplayString | read-only | Name of the pool that creates the binding. |
| IP me1200DhcpServerStatusBindingServerId | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.5 | IpAddress | read-only | IP address of the DHCP server to service the binding. |
| ME1 me1200DhcpServerStatusBindingVlanId | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.6 | ME1200Unsigned16 | read-only | The VLAN where the binding works on. |
| IP me1200DhcpServerStatusBindingSubnetMask | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.7 | IpAddress | read-only | Subnet mask of the DHCP client. |
| OID me1200DhcpServerStatusBindingClientIdentifierType | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.8 | ME1200ClientIdentifierType | read-only | Type of client identifier. DHCP option 61. Specify client's unique identifier to be used when the pool is the type of host. none(0) means the client identifier type is not defined yet. fqdn(1) means the client identifier type is type of FQDN (Fully Qualified Domain Name). mac(2) means the client identifier type is type of MAC address. |
| STR me1200DhcpServerStatusBindingClientIdentifierFqdn | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.9 | ME1200DisplayString | read-only | Client's Fully Qualified Domain Name. DHCP option 61. |
| MAC me1200DhcpServerStatusBindingClientIdentifierMac | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.10 | MacAddress | read-only | Client's MAC address. DHCP option 61. |
| MAC me1200DhcpServerStatusBindingMacAddress | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.11 | MacAddress | read-only | MAC address of the DHCP client. |
| STR me1200DhcpServerStatusBindingLease | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.12 | ME1200DisplayString | read-only | Lease time of the binding. |
| STR me1200DhcpServerStatusBindingTimeToExpire | 1.3.6.1.4.1.9.9.815.1.109.1.3.3.1.13 | ME1200DisplayString | read-only | remaining time to expire. |
| me1200DhcpServerControl | 1.3.6.1.4.1.9.9.815.1.109.1.4 | |||
| me1200DhcpServerControlStatistics | 1.3.6.1.4.1.9.9.815.1.109.1.4.1 | |||
| T/F me1200DhcpServerControlStatisticsClear | 1.3.6.1.4.1.9.9.815.1.109.1.4.1.1 | TruthValue | read-write | Clear all statistics. |
| me1200DhcpServerControlBinding | 1.3.6.1.4.1.9.9.815.1.109.1.4.2 | |||
| IP me1200DhcpServerControlBindingClearByIp | 1.3.6.1.4.1.9.9.815.1.109.1.4.2.1 | IpAddress | read-write | Clear binding with the IP address. If 0.0.0.0 then do nothing. |
| ME1 me1200DhcpServerControlBindingClearByType | 1.3.6.1.4.1.9.9.815.1.109.1.4.2.2 | ME1200BindingType | read-write | Clear binding by binding type. If none(0) then do nothing. |
| me1200DhcpServerMIBConformance | 1.3.6.1.4.1.9.9.815.1.109.2 | |||
| me1200DhcpServerMIBCompliances | 1.3.6.1.4.1.9.9.815.1.109.2.1 | |||
| me1200DhcpServerMIBCompliance | 1.3.6.1.4.1.9.9.815.1.109.2.1.1 | The compliance statement for the implementation. | ||
| me1200DhcpServerMIBGroups | 1.3.6.1.4.1.9.9.815.1.109.2.2 | |||
| me1200DhcpServerConfigGlobalsInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.1 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerConfigVlanTableInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.2 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerConfigExcludedTableInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.3 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerConfigExcludedIpTableRowEditorInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.4 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerConfigPoolTableInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.5 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerConfigPoolTableRowEditorInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.6 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerStatusDeclinedTableInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.7 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerStatusStatisticsInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.8 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerStatusBindingTableInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.9 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerControlStatisticsInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.10 | A collection of objects suitable for bulk operations. | ||
| me1200DhcpServerControlBindingInfoGroup | 1.3.6.1.4.1.9.9.815.1.109.2.2.11 | A collection of objects suitable for bulk operations. |
RFC description
Manages DHCP server configuration and pool information on Cisco ME1200 switches.
Start monitoring Cisco ME1200 Metro Ethernet switch (integrated DHCP server) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.