HUAWEI-SNA-DLSW-MIB

All MIBs › HUAWEI-SNA-DLSW-MIB

Organization: Huawei-3com Technologies co.,Ltd.

Last Updated: 2004-10-30

Category: Domain: SNA/Legacy, SNA and Legacy Protocols, Vendor: Huawei

Description: Huawei SNA DLSw (Data Link Switching) MIB for managing SNA/APPN traffic encapsulation over TCP/IP networks.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-SNA-DLSW-MIB?

This is Huawei's private MIB for DLSw (Data Link Switching), a mechanism for encapsulating legacy SNA and APPN traffic over TCP/IP networks, part of Huawei's enterprise MIB tree for its routing platforms. It exposes node-level configuration and status (version, vendor ID, pacing parameters) alongside per-peer transport connection information for the DLSw sessions the node maintains. Its monitoring emphasis is on software/service status: the operational state of the local DLSw node and the health of its individual peer connections, which together indicate whether legacy SNA/APPN traffic is being reliably bridged across the IP backbone. It builds on the same conceptual model as the IETF DLSw standard (RFC 2166/RFC 1795-style DLSw), extended here as a Huawei private implementation. It is deployed on Huawei routers acting as DLSw gateways bridging mainframe/SNA traffic over a modern IP WAN. Engineers can download the HUAWEI-SNA-DLSW-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-SNA-DLSW-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei router (SNA/DLSw gateway)

Monitoring Examples

An admin would check dlswNodeStatus to confirm the local DLSw node is operational, and read dlswNodeVersion, dlswNodeVendorID, and dlswNodeVersionString to verify implementation compatibility with a peer during interoperability troubleshooting. The dlswTConn-related objects expose the individual transport connections to DLSw peers, while dlswNodeKeepAlive, dlswNodeInitWindow, and dlswNodeMaxWindow show the pacing/keepalive parameters governing session stability. A peer connection dropping out of the TConn data combined with a degraded dlswNodeStatus would reveal a broken SNA-over-IP path.

What Can Be Monitored

DLSw node operational status
DLSw peer transport connections
node version/vendor information
keepalive and window/pacing parameters

Imported Objects

From HUAWEI-3COM-OID-MIB

products

OBJECT-IDENTITY

From RFC1213-MIB

ifIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowPointer
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using dlswRemotePeerRecvPacks OID:

Select a Huawei router (SNA/DLSw gateway) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dlswRemotePeerRecvPacks into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
dlsw	1.3.6.1.4.1.2011.2.34			private mib for dlsw
dlswNode	1.3.6.1.4.1.2011.2.34.1
OCT dlswNodeVersion	1.3.6.1.4.1.2011.2.34.1.1	OCTET STRING	read-only	This value identifies the particular version of the DLSw standard supported by this DLSw. The first octet is a hexadecimal value representing the DLSw standard Version number of this DLSw, and the second is a hexadecimal value representing the DLSw standard Release number. This information is reported in DLSw Capabilities Exchange.
OCT dlswNodeVendorID	1.3.6.1.4.1.2011.2.34.1.2	OCTET STRING	read-only	The value identifies the manufacturer's IEEE-assigned organizationally Unique Identifier (OUI) of this DLSw. This information is reported in DLSw Capabilities Exchange.
STR dlswNodeVersionString	1.3.6.1.4.1.2011.2.34.1.3	DisplayString	read-only	This string gives product-specific information about this DLSw (e.g., product name, code release and fix level). This flows in Capabilities Exchange messages.
INT dlswNodeStdPacingSupport	1.3.6.1.4.1.2011.2.34.1.4	INTEGER	read-only	Circuit pacing, as defined in the DLSw Standard, allows each of the two DLSw nodes on a circuit to control the amount of data the other is permitted to send to them. This object reflects the level of support the DLSw node has for this protocol. (1) means the node has no support for the standard circuit pacing flows; it may use RFC 1434+ methods only, or a proprietary flow control scheme. (2) means the node supports the standard scheme and can vary the window sizes it grants as a data receiver. (3) means the node supports the standard scheme but never varies its receive window size.
INT dlswNodeStatus	1.3.6.1.4.1.2011.2.34.1.5	INTEGER	read-write	The status of the DLSw part of the system.
LFS dlswNodeVirtualSegmentLFSize	1.3.6.1.4.1.2011.2.34.1.6	LFSize	read-write	The largest frame size (including DLC header and info field but not any MAC-level or framing octets) this DLSw can forward on any path through itself. This object can represent any box- level frame size forwarding restriction (e.g., from the use of fixed-size buffers). Some DLSw implementations will have no such restriction. This value will affect the LF size of circuits during circuit creation. The LF size of an existing circuit can be found in the RIF (Routing Information Field).
IP dlswNodeLocalAddr	1.3.6.1.4.1.2011.2.34.1.7	IpAddress	read-write	Local peer ip address.
INT dlswNodePriority	1.3.6.1.4.1.2011.2.34.1.8	INTEGER	read-write	The priority value of local peer. 65535 expresses the value is unknown
INT dlswNodeInitWindow	1.3.6.1.4.1.2011.2.34.1.9	INTEGER	read-write	The vlaue of init-window. 65535 expresses the value is unknown
INT dlswNodeKeepAlive	1.3.6.1.4.1.2011.2.34.1.10	INTEGER	read-write	The vlaue of keepalive interval. 65535 expresses the value is unknown
INT dlswNodeMaxWindow	1.3.6.1.4.1.2011.2.34.1.11	INTEGER	read-write	The value of max-window. 65535 expresses the value is unknown
INT dlswNodePermitDynamic	1.3.6.1.4.1.2011.2.34.1.12	INTEGER	read-write	To accept connections from non-configured remote peers when permit-dynamic is setted.
INT dlswNodeConnTimeout	1.3.6.1.4.1.2011.2.34.1.13	INTEGER	read-write	Define connected state timer(The unit is a thousandth of a second).
INT dlswNodeLocalPendTimeout	1.3.6.1.4.1.2011.2.34.1.14	INTEGER	read-write	Define connected state timer(The unit is a thousandth of a second).
INT dlswNodeRemotePendTimeout	1.3.6.1.4.1.2011.2.34.1.15	INTEGER	read-write	Define connected state timer(The unit is a thousandth of a second).
INT dlswNodeSnaCacheTimeout	1.3.6.1.4.1.2011.2.34.1.16	INTEGER	read-write	Define connected state timer(The unit is a thousandth of a second).
dlswTrapControl	1.3.6.1.4.1.2011.2.34.1.20
INT dlswTrapCntlState	1.3.6.1.4.1.2011.2.34.1.20.1	INTEGER	read-write	It is used to indicate whether the DLSw is permitted to emit traps.
dlswTConn	1.3.6.1.4.1.2011.2.34.2
dlswRemotePeerTable	1.3.6.1.4.1.2011.2.34.2.1		not-accessible	A list of tcp transport connections.
dlswRemotePeerEntry	1.3.6.1.4.1.2011.2.34.2.1.1		not-accessible	A list of remote peer information
IP dlswRemotePeerAddr	1.3.6.1.4.1.2011.2.34.2.1.1.1	IpAddress	read-only	The remote peer address for this transport connection.
OCT dlswRemotePeerVersion	1.3.6.1.4.1.2011.2.34.2.1.1.2	OCTET STRING	read-only	This value identifies which version (first octet) and release (second octet) of the DLSw standard is supported by this partner DLSw. This information is obtained from a DLSw capabilities exchange message received from the partner DLSw. A string of zero length is returned before a Capabilities Exchange message is received, or if one is never received. A conceptual row with a dlswTConnOperState of `connected' but a zero length partner version indicates that the partner is a non-standard DLSw partner. If an implementation chooses to keep dlswTConnOperEntrys in the `disconnected' state, this value should remain unchanged.
OCT dlswRemotePeerVendorID	1.3.6.1.4.1.2011.2.34.2.1.1.3	OCTET STRING	read-only	This value identifies the IEEE-assigned organizationally Unique Identifier (OUI) of the maker of this partner DLSw. This information is obtained from a DLSw capabilities exchange message received from the partner DLSw. A string of zero length is returned before a Capabilities Exchange message is received, or if one is never received. If an implementation chooses to keep dlswTConnOperEntrys in the `disconnected' state, this value should remain unchanged.
INT dlswRemotePeerPaceWindInit	1.3.6.1.4.1.2011.2.34.2.1.1.4	INTEGER	read-only	The value of the partner initial receive pacing window. This is our initial send pacing window for all new circuits on this transport connection, as modified and granted by the first flow control indication the partner sends on each circuit. This information is obtained from a DLSw capabilities exchange message received from the partner DLSw. A value of zero is returned before a Capabilities Exchange message is received, or if one is never received. If an implementation chooses to keep dlswTConnOperEntrys in the `disconnected' state, this value should remain unchanged.
STR dlswRemotePeerVersionString	1.3.6.1.4.1.2011.2.34.2.1.1.5	DisplayString	read-only	This value identifies the particular product version (e.g., product name, code level, fix level) of this partner DLSw. The format of the actual version string is vendor-specific. This information is obtained from a DLSw capabilities exchange message received from the partner DLSw. A string of zero length is returned before a Capabilities Exchange message is received, if one is never received, or if one is received but it does not contain a version string. If an implementation chooses to keep dlswTConnOperEntrys in the `disconnected' state, this value should remain unchanged.
INT dlswRemotePeerIsConfig	1.3.6.1.4.1.2011.2.34.2.1.1.6	INTEGER	read-only	The current remote peer is configrured when the value is 'yes'.
INT dlswRemotePeerCost	1.3.6.1.4.1.2011.2.34.2.1.1.7	INTEGER	read-write	The cost for remote peer.
INT dlswRemotePeerKeepAlive	1.3.6.1.4.1.2011.2.34.2.1.1.8	INTEGER	read-write	The keepalive interval value.
LFS dlswRemotePeerLf	1.3.6.1.4.1.2011.2.34.2.1.1.9	LFSize	read-write	The the largest frame size.
INT dlswRemotePeerTcpQueneMax	1.3.6.1.4.1.2011.2.34.2.1.1.10	INTEGER	read-write	The max tcp queue value.
INT dlswRemotePeerHaveBackup	1.3.6.1.4.1.2011.2.34.2.1.1.11	INTEGER	read-only	There is another remote peer whitch is configrued as the backup of the current remote peer .
INT dlswRemotePeerIsBackup	1.3.6.1.4.1.2011.2.34.2.1.1.12	INTEGER	read-only	The current remote peer is configrued as the backup of another configured remote peer .
IP dlswRemotePeerBackupAddr	1.3.6.1.4.1.2011.2.34.2.1.1.13	IpAddress	read-only	It is the IP ADDRESS of an configured remote peer of whitch the current remote peer is configrued as the backup
INT dlswRemotePeerLinger	1.3.6.1.4.1.2011.2.34.2.1.1.14	INTEGER	read-write	Buckup Peer linger
INT dlswRemotePeerLinkState	1.3.6.1.4.1.2011.2.34.2.1.1.15	INTEGER	read-only	The state of this tcp transport connection.
C32 dlswRemotePeerRecvPacksEx	1.3.6.1.4.1.2011.2.34.2.1.1.16	Counter32	read-only	The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection.
C32 dlswRemotePeerSendPacks	1.3.6.1.4.1.2011.2.34.2.1.1.17	Counter32	read-only	The number of Switch-to-Switch Protocol (SSP) messages sent on this tcp transport connection.
C32 dlswRemotePeerDrops	1.3.6.1.4.1.2011.2.34.2.1.1.18	Counter32	read-only	The number of Switch-to-Switch Protocol (SSP) messages dropped on this tcp transport connection.
C32 dlswRemotePeerUptime	1.3.6.1.4.1.2011.2.34.2.1.1.19	Counter32	read-only	The amount of time (in seconds ) since this transport connection last entered the 'connected' state.
ENT dlswRemotePeerEntryStatus	1.3.6.1.4.1.2011.2.34.2.1.1.20	EntryStatus	read-write	This object is used by the manager to create or delete the row entry in the dlswRemotePeerTable following the EntryStatus textual convention.
dlswBridgeGroup	1.3.6.1.4.1.2011.2.34.3
dlswBridgeTable	1.3.6.1.4.1.2011.2.34.3.1		not-accessible	The list of bridge group whitch has been created.
dlswBridgeEntry	1.3.6.1.4.1.2011.2.34.3.1.1		not-accessible	The list of bridge information
INT dlswBridgeNum	1.3.6.1.4.1.2011.2.34.3.1.1.1	INTEGER	read-only	This value identifies the bridge number .
CRE dlswBridgeStatus	1.3.6.1.4.1.2011.2.34.3.1.1.2	CreateLineFlag	read-write	This value whitch is equal to 'DeleteLine' identifies to delete a conceptual raw.
dlswBridgeIfTable	1.3.6.1.4.1.2011.2.34.3.2		not-accessible	The list of interfaces on which DLSw is active.
dlswBridgeIfEntry	1.3.6.1.4.1.2011.2.34.3.2.1		not-accessible	The list of bridge interface information
INT dlswBridgeIfBriGru	1.3.6.1.4.1.2011.2.34.3.2.1.1	INTEGER	read-write	This value identifies the bridge number attached to the interface.
STR dlswBridgeIfName	1.3.6.1.4.1.2011.2.34.3.2.1.2	DisplayString	read-only	The name of the interface.
ENT dlswBridgeIfStatus	1.3.6.1.4.1.2011.2.34.3.2.1.3	EntryStatus	read-write	This value whitch is equal to 'invalid' identifies to delete a conceptual raw
dlswLocDirectory	1.3.6.1.4.1.2011.2.34.4
dlswLocMacTable	1.3.6.1.4.1.2011.2.34.4.1		not-accessible	This table contains locations of MAC addresses. They are local and reachable
dlswLocMacEntry	1.3.6.1.4.1.2011.2.34.4.1.1		not-accessible
INT dlswLocMacHashIndex	1.3.6.1.4.1.2011.2.34.4.1.1.1	INTEGER	read-only	The hash value.
INT dlswLocMacHashIndexSeqNum	1.3.6.1.4.1.2011.2.34.4.1.1.2	INTEGER	read-only	The sequence num with smae hash value.
ADR dlswLocMacMac	1.3.6.1.4.1.2011.2.34.4.1.1.3	MacAddressNC	read-only	The MAC address.
STR dlswLocMacLocalInterfaceName	1.3.6.1.4.1.2011.2.34.4.1.1.4	DisplayString	read-only	The value is the interface name when dlswLocMacLocationType is 'local'.
dlswCircuit	1.3.6.1.4.1.2011.2.34.5
dlswCircuitTable	1.3.6.1.4.1.2011.2.34.5.1		not-accessible	This table is the circuit representation in the DLSw entity. Virtual data links are used to represent any internal end stations. There is a conceptual row associated with each data link. Thus, for circuits without an intervening transport connection, there are two conceptual rows for each circuit. The table consists of the circuits being established, established, and as an implementation option, circuits that have been disconnected. For circuits carried over transport connections, an entry is created after the CUR_cs was sent or received. For circuits between two locally attached devices, or internal virtual MAC addresses, an entry is created when the equivalent of CUR_cs sent/received status is reached. End station 1 (S1) and End station 2 (S2) are used to represent the two end stations of the circuit. S1 is always an end station which is locally attached. S2 may be locally attached or remote. If it is locally attached, the circuit will be represented by two rows indexed by (A, B) and (B, A) where A & B are the relevant MACs/SAPs. The table may be used to store the causes of disconnection of circuits. It is recommended that the oldest disconnected circuit entry be removed from this table when the memory space of disconnected circuits is needed.
dlswCircuitEntry	1.3.6.1.4.1.2011.2.34.5.1.1		not-accessible	the list of circuit information
INT dlswCircuitS1CircuitId	1.3.6.1.4.1.2011.2.34.5.1.1.1	INTEGER	read-only	The Circuit ID assigned by this DLSw node to this circuit. The first four octets are the DLC port Id, and the second four octets are the Data Link Correlator. If the DLSw SSP was not used to establish this circuit, the value will be a string of zero length.
ADR dlswCircuitS1Mac	1.3.6.1.4.1.2011.2.34.5.1.1.2	MacAddressNC	read-only	The MAC Address of End Station 1 (S1) used for this circuit.
OCT dlswCircuitS1Sap	1.3.6.1.4.1.2011.2.34.5.1.1.3	OCTET STRING	read-only	The SAP at End Station 1 (S1) used for this circuit.
ADR dlswCircuitS2Mac	1.3.6.1.4.1.2011.2.34.5.1.1.4	MacAddressNC	read-only	The MAC Address of End Station 2 (S2) used for this circuit.
OCT dlswCircuitS2Sap	1.3.6.1.4.1.2011.2.34.5.1.1.5	OCTET STRING	read-only	The SAP at End Station 2 (S2) used for this circuit.
INT dlswCircuitS1IfIndex	1.3.6.1.4.1.2011.2.34.5.1.1.6	INTEGER	read-only	The ifEntry index of the local interface through which S1 can be reached.
STR dlswCircuitS1Ifname	1.3.6.1.4.1.2011.2.34.5.1.1.7	DisplayString	read-only	The name of the interface whose Ifdex is dlswCircuitS1IfIndex.
DLC dlswCircuitS1DlcType	1.3.6.1.4.1.2011.2.34.5.1.1.8	DlcType	read-only	The DLC protocol in use between the DLSw node and S1.
IP dlswCircuitS2TAddress	1.3.6.1.4.1.2011.2.34.5.1.1.9	IpAddress	read-only	If the location of End Station 2 is remote, this object contains the address of the partner DLSw, else it will be an OCTET STRING of zero length.
INT dlswCircuitS2CircuitId	1.3.6.1.4.1.2011.2.34.5.1.1.10	INTEGER	read-only	The Circuit ID assigned to this circuit by the partner DLSw node. The first four octets are the DLC port Id, and the second four octets are the Data Link Correlator. If the DLSw SSP was not used to establish this circuit, the value will be a string of zero length.
INT dlswCircuitOrigin	1.3.6.1.4.1.2011.2.34.5.1.1.11	INTEGER	read-only	This object specifies which of the two end stations initiated the establishment of this circuit.
TIK dlswCircuitEntryTime	1.3.6.1.4.1.2011.2.34.5.1.1.12	TimeTicks	read-only	The amount of time (in hundredths of a second) since this circuit table conceptual row was created.
TIK dlswCircuitStateTime	1.3.6.1.4.1.2011.2.34.5.1.1.13	TimeTicks	read-only	The amount of time (in hundredths of a second) since this circuit entered the current state.
INT dlswCircuitState	1.3.6.1.4.1.2011.2.34.5.1.1.14	INTEGER	read-only	The current state of this circuit. The agent, implementation specific, may choose to keep entries for some period of time after circuit disconnect, so the manager can gather the time and cause of disconnection. While all of the specified values may be returned from a GET operation, the only SETable value is `disconnectPending'. When this value is set, DLSw should perform the appropriate action given its previous state (e.g., send HALT_DL if the state was `connected') to bring the circuit down to the `disconnected' state. Both the partner DLSw and local end station(s) should be notified as appropriate. This MIB provides no facility to re-establish a disconnected circuit, because in DLSw this should be an end station-driven function.
INT dlswCircuitFCSendGrantedUnits	1.3.6.1.4.1.2011.2.34.5.1.1.15	INTEGER	read-only	The number of paced SSP messages that this DLSw is currently authorized to send on this circuit before it must stop and wait for an additional flow control indication from the partner DLSw. The value zero should be returned if this circuit is not running the DLSw pacing protocol.
INT dlswCircuitFCSendCurrentWndw	1.3.6.1.4.1.2011.2.34.5.1.1.16	INTEGER	read-only	The current window size that this DLSw is using in its role as a data sender. This is the value by which this DLSw would increase the number of messages it is authorized to send, if it were to receive a flow control indication with the bits specifying `repeat window'. The value zero should be returned if this circuit is not running the DLSw pacing protocol.
INT dlswCircuitFCRecvGrantedUnits	1.3.6.1.4.1.2011.2.34.5.1.1.17	INTEGER	read-only	The current number of paced SSP messages that this DLSw has authorized the partner DLSw to send on this circuit before the partner DLSw must stop and wait for an additional flow control indication from this DLSw. The value zero should be returned if this circuit is not running the DLSw pacing protocol.
INT dlswCircuitFCRecvCurrentWndw	1.3.6.1.4.1.2011.2.34.5.1.1.18	INTEGER	read-only	The current window size that this DLSw is using in its role as a data receiver. This is the number of additional paced SSP messages that this DLSw would be authorizing its DLSw partner to send, if this DLSw were to send a flow control indication with the bits specifying `repeat window'. The value zero should be returned if this circuit is not running the DLSw pacing protocol.
dlswSdlc	1.3.6.1.4.1.2011.2.34.6
dlswSdlcPortTable	1.3.6.1.4.1.2011.2.34.6.1		not-accessible	The table defines parameters for the interfaces with the encapunation of SDLC.
dlswSdlcPortEntry	1.3.6.1.4.1.2011.2.34.6.1.1		not-accessible
STR dlswSdlcPortSerialName	1.3.6.1.4.1.2011.2.34.6.1.1.1	DisplayString	read-only	The name of serial port.
INT dlswSdlcPortEncap	1.3.6.1.4.1.2011.2.34.6.1.1.2	INTEGER	read-only	The encapunation of the interface.
INT dlswSdlcPortRole	1.3.6.1.4.1.2011.2.34.6.1.1.3	INTEGER	read-write	The SDLC role of interface.
ADR dlswSdlcPortVmac	1.3.6.1.4.1.2011.2.34.6.1.1.4	MacAddressNC	read-write	Define virtual mac address.
INT dlswSdlcPortHoldq	1.3.6.1.4.1.2011.2.34.6.1.1.5	INTEGER	read-write	Size of hold queue.
INT dlswSdlcPortK	1.3.6.1.4.1.2011.2.34.6.1.1.6	INTEGER	read-write	Size of local send window.
INT dlswSdlcPortModule	1.3.6.1.4.1.2011.2.34.6.1.1.7	INTEGER	read-write	Size of modulus.
INT dlswSdlcPortN1	1.3.6.1.4.1.2011.2.34.6.1.1.8	INTEGER	read-write	Max number of bits for incoming frames.
INT dlswSdlcPortN2	1.3.6.1.4.1.2011.2.34.6.1.1.9	INTEGER	read-write	Number of timers to retry an operation.
INT dlswSdlcPortPollPauseTimer	1.3.6.1.4.1.2011.2.34.6.1.1.10	INTEGER	read-write	Time between polls for each secondary SDLC station. The unit is thousandth of a second.
INT dlswSdlcPortSimultaneousEnable	1.3.6.1.4.1.2011.2.34.6.1.1.11	INTEGER	read-write	Activate SDLC two-way simultaneous mode.
INT dlswSdlcPortT1	1.3.6.1.4.1.2011.2.34.6.1.1.12	INTEGER	read-write	Time to wait for a reply to a frame.
INT dlswSdlcPortT2	1.3.6.1.4.1.2011.2.34.6.1.1.13	INTEGER	read-write	Time to wait for a reply used by secondary station.
dlswSdlcLsTable	1.3.6.1.4.1.2011.2.34.6.2		not-accessible	The table defines the virtual MAC addresses for those SDLC link stations that participate in data link switching.
dlswSdlcLsEntry	1.3.6.1.4.1.2011.2.34.6.2.1		not-accessible
INT dlswSdlcLsAddress	1.3.6.1.4.1.2011.2.34.6.2.1.1	INTEGER	read-only	Define SDLC address.
INT dlswSdlcLsLocalId	1.3.6.1.4.1.2011.2.34.6.2.1.2	INTEGER	read-write	The value is XID.
ADR dlswSdlcLsRemoteMac	1.3.6.1.4.1.2011.2.34.6.2.1.3	MacAddressNC	read-write	The MAC address to which DLSw should attempt to connect this link station. If this information is not available, a length of zero for this object should be returned
INT dlswSdlcLsSsap	1.3.6.1.4.1.2011.2.34.6.2.1.4	INTEGER	read-write	Source SAP of partner.
INT dlswSdlcLsDsap	1.3.6.1.4.1.2011.2.34.6.2.1.5	INTEGER	read-write	Destination SAP of partner.
ENT dlswSdlcLsStatus	1.3.6.1.4.1.2011.2.34.6.2.1.6	EntryStatus	read-write	This object is used by the manager to create or delete the row entry in the DlswSdlcLsTable following the EntryStatus textual convention.
dlswLlc2	1.3.6.1.4.1.2011.2.34.7
dlswLlc2PortTable	1.3.6.1.4.1.2011.2.34.7.1		not-accessible	The table defines parameters for the interfaces with the encapunation of Llc2.
dlswLlc2PortEntry	1.3.6.1.4.1.2011.2.34.7.1.1		not-accessible
INT dlswLLC2PortAckDelayTime	1.3.6.1.4.1.2011.2.34.7.1.1.1	INTEGER	read-write	Max time allows I-frames incoming without replay ACK.
INT dlswLLC2PortAckMax	1.3.6.1.4.1.2011.2.34.7.1.1.2	INTEGER	read-write	Max number of I-frames received before ACK.
INT dlswLLC2PortLocalWnd	1.3.6.1.4.1.2011.2.34.7.1.1.3	INTEGER	read-write	Max number of I-frames to send before received ACK.
INT dlswLLC2PortModulus	1.3.6.1.4.1.2011.2.34.7.1.1.4	INTEGER	read-write	Modulus of LLC2.
INT dlswLLC2PortN2	1.3.6.1.4.1.2011.2.34.7.1.1.5	INTEGER	read-write	Retry times of operations.
INT dlswLLC2PortT1	1.3.6.1.4.1.2011.2.34.7.1.1.6	INTEGER	read-write	Waiting for ACK time after sent a I-frame.
INT dlswLLC2PortTbusyTime	1.3.6.1.4.1.2011.2.34.7.1.1.7	INTEGER	read-write	Waiting time while other LLC2 station is in busy state.
INT dlswLLC2PortTpfTime	1.3.6.1.4.1.2011.2.34.7.1.1.8	INTEGER	read-write	Waiting time after a P frame is sent.
INT dlswLLC2PortTrejTime	1.3.6.1.4.1.2011.2.34.7.1.1.9	INTEGER	read-write	Waiting time after a REJ frame is sent.
INT dlswLLC2PortTxqMax	1.3.6.1.4.1.2011.2.34.7.1.1.10	INTEGER	read-write	Queue for sending llc2 I-frames.
dlswTraps	1.3.6.1.4.1.2011.2.34.8
dlswTrapsV2	1.3.6.1.4.1.2011.2.34.8.0
NTF dlswTrapTConnPartnerReject	1.3.6.1.4.1.2011.2.34.8.0.1			This trap is sent each time a transport connection is rejected by a partner DLSw during Capabilities Exchanges. The emission of this trap is controlled by dlswTrapCntlCircuit.
NTF dlswTrapTConnChangeState	1.3.6.1.4.1.2011.2.34.8.0.2			This trap is sent each time a transport connection changes state. The emission of this trap is controlled by dlswTrapCntlTConn.
NTF dlswTrapCircuitChangeState	1.3.6.1.4.1.2011.2.34.8.0.3			This trap is sent each time a circuit change state. The emission of this trap is controlled by dlswTrapCntlCircuit.

RFC description

Manages DLSw (Data Link Switching) for bridging SNA (Systems Network Architecture) traffic over IP networks.

Start monitoring Huawei router (SNA/DLSw gateway) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-SNA-DLSW-MIB