HUAWEI-IPDSLAM-PPPOE-MIB

All MIBs › HUAWEI-IPDSLAM-PPPOE-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2011-08-11

Category: Domain: DSL, Vendor: Huawei

Description: Huawei IP-DSLAM PPPoE MIB providing PPPoE session management, intermediate agent configuration, and subscriber session statistics on IP DSLAMs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-IPDSLAM-PPPOE-MIB?

HUAWEI-IPDSLAM-PPPOE-MIB is a Huawei enterprise MIB module used to manage PPPoE (Point-to-Point Protocol over Ethernet) functionality on Huawei IP DSLAM (Digital Subscriber Line Access Multiplexer) broadband access equipment. It exposes configuration and status data for PPPoE intermediate-agent features, including single-MAC PPPoE mode, PPPoE simulation/test sessions, and PPPoE client session parameters used in subscriber access networks. As a monitoring resource it is primarily used to track the operational status and configuration state of PPPoE session handling on the DSLAM's line cards, rather than deep hardware sensor data, though overall DSLAM chassis health is typically covered by companion Huawei hardware MIBs. It has an implicit dependency on standard IF-MIB interface indexing and other Huawei IP-DSLAM MIBs for correlating PPPoE sessions to physical/logical ports. It is deployed in telecom central-office or cabinet DSLAM equipment used by broadband/ISP operators to provision and troubleshoot PPPoE-based subscriber sessions, making HUAWEI-IPDSLAM-PPPOE-MIB SNMP monitoring a routine part of broadband access operations.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-IPDSLAM-PPPOE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei IP DSLAM broadband access equipment

Monitoring Examples

No concrete object or table names were captured for this MIB, so a specific polling example cannot be grounded in verified object names. Based on the module description, an operator would generally be expected to check PPPoE single-MAC configuration and PPPoE client/simulation session state per port to confirm subscriber sessions are being established correctly. This remains a general characterization of the module's intent rather than a confirmed example.

What Can Be Monitored

PPPoE single-MAC mode configuration
PPPoE simulation session status
PPPoE client session status

Imported Objects

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwIpDslamPPPoE	1.3.6.1.4.1.2011.6.107			The mib is used for defining the MIB objects of the pppoe single-mac, pppoe simulation and pppoe client.
INT hwIpDslamPPPoEMacMode	1.3.6.1.4.1.2011.6.107.1	INTEGER	read-write	Used for setting and querying the MAC address mode of a PPPoE user. Options: 1. multiMac(1) -indicates the multiple MAC address mode of the PPPoE user 2. singleMac(2) -indicates the single MAC address mode of the PPPoE user Default: multiMac(1)
hwPPPoESmltAdminTable	1.3.6.1.4.1.2011.6.107.2		not-accessible	Used for starting or stopping the PPPoE dialup simulation service, and for querying the result of the simulated PPPoE dialup. The index of this table is hwPPPoESmltObjIndex.
hwPPPoESmltAdminEntry	1.3.6.1.4.1.2011.6.107.2.1		not-accessible	Used for starting or stopping the PPPoE dialup simulation service, and for querying the result of the simulated PPPoE dialup. The index of this entry is hwPPPoESmltObjIndex.
I32 hwPPPoESmltObjIndex	1.3.6.1.4.1.2011.6.107.2.1.1	Integer32	read-only	Indicates the index of hwPPPoESmltAdminTable. This leaf means the dialup ID. Currently, only one user is supported. The maximum value of the index is 1. If you specify it to 4294967295, the system will automatically allocates an idle index.
I32 hwPPPoESmltSrvFlowIndex	1.3.6.1.4.1.2011.6.107.2.1.2	Integer32	read-write	Indicates the service port ID. Here, it refers to the ID of a service port that is already created on the current device. The service port ID on the NMS is larger than the service port ID on the host by 1.
OCT hwPPPoESmltUserName	1.3.6.1.4.1.2011.6.107.2.1.3	OCTET STRING	read-write	Indicates the user name.
OCT hwPPPoESmltUserPassword	1.3.6.1.4.1.2011.6.107.2.1.4	OCTET STRING	read-write	Indicates the user password for authentication.
INT hwPPPoESmltAuthMode	1.3.6.1.4.1.2011.6.107.2.1.5	INTEGER	read-write	Indicates the user authentication mode. Currently, the device supports two modes, Options: 1. chap(1) -Challenge-Handshake Authentication Protocol mode 2. pap(2) -Password Authentication Protocol mode
I32 hwPPPoESmltOverTime	1.3.6.1.4.1.2011.6.107.2.1.6	Integer32	read-write	Indicates the test timeout time. It is an optional parameter. Unit: second Range: 5-60 Default: 5
INT hwPPPoESmltCurrentPhase	1.3.6.1.4.1.2011.6.107.2.1.7	INTEGER	read-only	Indicates the current stage of the simulation. Options: 1. discovery(1) -indicates the discovery stage of PPPoE dialup 2. lcp(2) -indicates the LCP negotiation stage. In this stage, the parameters required for creating, maintaining, and terminating the PPP networking are negotiated. 3. authentication(3) -indicates the authentication stage. In this stage, the user is authenticated after the PPPoE connection is set up. 4. ncp(4) -indicates the NCP negotiation stage. In this stage, the network-layer compression protocol and IP address are negotiated. 5. online(5) -indicates the data transmission stage 6. stop(6) -indicates that PPPoE dialup is not performed
INT hwPPPoESmltResult	1.3.6.1.4.1.2011.6.107.2.1.8	INTEGER	read-only	Indicates the simulation result. Options: 1. success(0) -indicates the PPPoE simulation is success 2. otherError(1) -indicates other errors 3. timeout(2) -indicates the PPPoE simulation timeout 4. paramNegoFail(3) -indicates parameter negotiation failure 5. authenticationFail(4) -indicates the simulation authentication is failed 6. peerDownRequest(5) -indicates that the dialup request is denied by the peer end 7. waitPADOTimeout(6) -indicates that sending PADI and waiting for PADO time out 8. waitPADSTimeout(7) -indicates that sending PADR and waiting for PADS time out 9. waitPPPTimeout(8) -indicates waiting for PPP times out, such as an LCP timeout or an NCP timeout. 10. linkAbnormal(9) -indicates the link of the PPPoE simulation is abnormal
DAT hwPPPoESmltStartTime	1.3.6.1.4.1.2011.6.107.2.1.9	DateAndTime	read-only	Indicates the simulation start time. Data type: DateAndTime. For example, 2010-2-6,1:38:50.0,+8:0.
DAT hwPPPoESmltEndTime	1.3.6.1.4.1.2011.6.107.2.1.10	DateAndTime	read-only	Indicates the simulation end time. Data type: DateAndTime. For example, 2010-2-6,1:38:50.0,+8:0.
G32 hwPPPoESmltUserSessionId	1.3.6.1.4.1.2011.6.107.2.1.11	Gauge32	read-only	Indicates the obtained session ID of the user. Range: 1-4294967295
IP hwPPPoESmltUserIp	1.3.6.1.4.1.2011.6.107.2.1.12	IpAddress	read-only	Indicates the obtained IP address of the user. Data type: IpAddress.
IP hwPPPoESmltGatewayIp	1.3.6.1.4.1.2011.6.107.2.1.13	IpAddress	read-only	Indicates the obtained gateway IP address. Data type: IpAddress.
ROW hwPPPoESmltRowStatus	1.3.6.1.4.1.2011.6.107.2.1.14	RowStatus	read-create	Indicates the row status. It is used for starting or stopping the PPPoE dialup simulation service. Only options active(1), createAndGo(4), and destroy(6) are supported. To start the PPPoE dialup simulation service, you must input hwPPPoESmltObjIndex, hwPPPoESmltSrvFlowIndex, hwPPPoESmltUserName, and hwPPPoESmltUserPassword, and set the value of the row status to createAndGo(4). To stop the PPPoE dialup simulation service, you must input hwPPPoESmltObjIndex, and set the value of the row status to destroy(6). In the query about the PPPoE dialup simulation service, the value of the row status is active(1). Options: 1. active(1) -indicates the query operation 2. createAndGo(4) -indicates starting the PPPoE dialup simulation service 3. destroy(6) -indicates stopping the PPPoE dialup simulation service
hwPPPoEClientConfigTable	1.3.6.1.4.1.2011.6.107.3		not-accessible	Used for setting and querying the configuration information about a PPPoE client. The index of this table is hwPPPoEClientConfigName.
hwPPPoEClientConfigEntry	1.3.6.1.4.1.2011.6.107.3.1		not-accessible	Used for setting and querying the configuration information about a PPPoE client. The index of this entry is hwPPPoEClientConfigName.
OCT hwPPPoEClientConfigName	1.3.6.1.4.1.2011.6.107.3.1.1	OCTET STRING	not-accessible	Indicates the identification of a PPPoE client.Range: 1-32 characters. The PPPoE client identification must be presented in the ASCII codes of the corresponding characters. For example, if the PPPoE client identification is aa, it must be presented as 2.97.97. 2 indicates the length of the characters, and 97 indicates the ASCII code corresponding to character a. 2 and 97s are separated by the '.' sign.
OCT hwPPPoEClientConfigUserName	1.3.6.1.4.1.2011.6.107.3.1.2	OCTET STRING	read-create	Used for setting or querying the user name of PPPoE dialup. Range: 1-65 characters.
OCT hwPPPoEClientConfigUserPassword	1.3.6.1.4.1.2011.6.107.3.1.3	OCTET STRING	read-create	Used for setting or querying the user password of PPPoE dialup. Range: 0-16 characters.
INT hwPPPoEClientConfigAuthMode	1.3.6.1.4.1.2011.6.107.3.1.4	INTEGER	read-create	Used for setting or querying the authentication mode of a PPPoE client. Options: 1. chap(1) -Challenge-Handshake Authentication Protocol mode 2. pap(2) -Password Authentication Protocol mode Default: chap(1)
I32 hwPPPoEClientConfigVlanID	1.3.6.1.4.1.2011.6.107.3.1.5	Integer32	read-create	Used for setting or querying the VLAN for the dialup of a PPPoE client. Range: 1-4093 Default: 1
INT hwPPPoEClientConfigEnableFlag	1.3.6.1.4.1.2011.6.107.3.1.6	INTEGER	read-create	Used for setting (enabling/disabling) or querying the status of the PPPoE dialup function. Options: 1. enable(1) -indicates the PPPoE dialup function is enabled 2. disable(2) -indicates the PPPoE dialup function is disabled Default: disable(2)
I32 hwPPPoEClientConfigIntervalTime	1.3.6.1.4.1.2011.6.107.3.1.7	Integer32	read-create	Used for setting or querying the interval for sending the Echo-Request packet. Range: 1-65535 Unit: second Default: 20s
I32 hwPPPoEClientConfigRetransmitTimes	1.3.6.1.4.1.2011.6.107.3.1.8	Integer32	read-create	Indicates the count of retransmitting the Echo-Request packet at timeout. Range: 1-10 Default: 3
ROW hwPPPoEClientConfigRowStatus	1.3.6.1.4.1.2011.6.107.3.1.9	RowStatus	read-create	Indicates the row status. It is used for setting, modifying, or deleting the identification of a PPPoE client. Options active(1), createAndGo(4), and destroy(6) are supported. To set the identification of a PPPoE client, set the value of hwPPPoEClientConfigRowStatus to createAndGo(4). To delete the configuration of a specified PPPoE client, set the value of hwPPPoEClientConfigRowStatus to destroy(6). During the query operation, the value of this leaf is always active(1). Options: 1. active(1) -indicates the query operation 2. createAndGo(4) -indicates setting the identification of a PPPoE client 3. destroy(6) -indicates deleting the configuration of a specified PPPoE client
hwPPPoEClientSessionTable	1.3.6.1.4.1.2011.6.107.4		not-accessible	Used for setting and querying the information about the session of a PPPoE client. The index of this table is hwPPPoEClientConfigName. To serve as an index, the value of hwPPPoEClientConfigName must be already configured in hwPPPoEClientConfigTable.
hwPPPoEClientSessionEntry	1.3.6.1.4.1.2011.6.107.4.1		not-accessible	Used for setting and querying the information about the session of a PPPoE client. The index of this entry is hwPPPoEClientConfigName. To serve as an index, the value of hwPPPoEClientConfigName must be already configured in hwPPPoEClientConfigTable.
INT hwPPPoEClientSessionCurrentPhase	1.3.6.1.4.1.2011.6.107.4.1.1	INTEGER	read-only	Used for querying the current stage of a PPPoE session. Options: 1. discovery(1) -indicates the discovery stage of PPPoE dialup 2. lcp(2) -indicates the LCP negotiation stage. In this stage, the parameters required for creating, maintaining, and terminating the PPP networking are negotiated. 3. authentication(3) -indicates the authentication stage. In this stage, the user is authenticated after the PPPoE connection is set up. 4. ncp(4) -indicates the NCP negotiation stage. In this stage, the network-layer compression protocol and IP address are negotiated. 5. online(5) -indicates the data transmission stage 6. disable(6) -indicates that PPPoE dialup is not performed
G32 hwPPPoEClientSessionId	1.3.6.1.4.1.2011.6.107.4.1.2	Gauge32	read-only	Used for querying the session ID obtained by a PPPoE client. When PPPoE dialup is not performed or the dialup fails, the session ID is an invalid value 4294967295.
IP hwPPPoEClientSessionUserIp	1.3.6.1.4.1.2011.6.107.4.1.3	IpAddress	read-only	Used for querying the IP address of a PPPoE client.
OCT hwPPPoEClientSessionUserMac	1.3.6.1.4.1.2011.6.107.4.1.4	OCTET STRING	read-only	Used for querying the MAC address of a PPPoE client.
IP hwPPPoEClientSessionGatewayIp	1.3.6.1.4.1.2011.6.107.4.1.5	IpAddress	read-only	Used for querying the IP address of the gateway to which a PPPoE client is connected.
OCT hwPPPoEClientSessionGatewayMac	1.3.6.1.4.1.2011.6.107.4.1.6	OCTET STRING	read-only	Used for querying the MAC address of the gateway to which a PPPoE client is connected.
G32 hwPPPoEClientSessionStartTime	1.3.6.1.4.1.2011.6.107.4.1.7	Gauge32	read-only	Used for querying the dialup start time of a PPPoE client, in the unit of second. The time value indicates the seconds lapsed from the Greenwich time 1970-01-01 00:00:00 to the dialup starting.
G32 hwPPPoEClientSessionEndTime	1.3.6.1.4.1.2011.6.107.4.1.8	Gauge32	read-only	Used for querying the dialup end time of a PPPoE client, in the unit of second. The time value indicates the seconds lapsed from the Greenwich time 1970-01-01 00:00:00 to the dialup ending.
INT hwPPPoEClientSessionDiagnostic	1.3.6.1.4.1.2011.6.107.4.1.9	INTEGER	read-only	Used for querying the information about a PPPoE dialup result. Options: 1. success(1) -indicates successful PPPoE dialup 2. otherError(2) -indicates other errors 3. timeout(3) -indicates dialup timeout 4. waitPADOTimeout(4) -indicates that sending PADI and waiting for PADO time out 5. waitPADSTimeout(5) -indicates that sending PADR and waiting for PADS time out 6. waitPPPTimeout(6) -indicates waiting for PPP times out, such as an LCP timeout or an NCP timeout. 7. paramNegoFail(7) -indicates parameter negotiation failure 8. authenticationFail(8) -indicates authentication failure 9. peerDownRequest(9) -indicates that the dialup request is denied by the peer end 10.linkAbnormal(10) -indicates that the link is unnormal
hwIpDslamPPPoETrapsVbOids	1.3.6.1.4.1.2011.6.107.5
I32 hwIpDslamPPPoESerialNo	1.3.6.1.4.1.2011.6.107.5.1	Integer32	accessible-for-notify	It indicates Serial Id which is allocated by server.
hwIpDslamPPPoETraps	1.3.6.1.4.1.2011.6.107.6
hwIpDslamPPPoECommonTraps	1.3.6.1.4.1.2011.6.107.6.1
hwIpDslamPPPoECommonTrapssPrefix	1.3.6.1.4.1.2011.6.107.6.1.0
NTF hwIpDslamPPPoESmltTrap	1.3.6.1.4.1.2011.6.107.6.1.0.1			The trap is generated when PPPoE simulation start . The hwIpDslamPPPoESerialNo indicates Serial Id which is allocated by server, defined in hwIpDslamPPPoETrapsVbOids.
hwPPPoESmacCurrentUserTable	1.3.6.1.4.1.2011.6.107.7		not-accessible	Used for querying the information about a PPPoE single-MAC user. The indexes of this table are ifIndex and hwPPPoESmacUserIndex.
hwPPPoESmacCurrentUserEntry	1.3.6.1.4.1.2011.6.107.7.1		not-accessible	Used for querying the information about a PPPoE single-MAC user. The indexes of this entry are ifIndex and hwPPPoESmacUserIndex.
I32 hwPPPoESmacUserIndex	1.3.6.1.4.1.2011.6.107.7.1.1	Integer32	read-only	PPPoE SMAC user index.
I32 hwPPPoESmacUserFlowId	1.3.6.1.4.1.2011.6.107.7.1.2	Integer32	read-only	PPPoE user flow ID.
G32 hwPPPoESmacUserSessionId	1.3.6.1.4.1.2011.6.107.7.1.3	Gauge32	read-only	PPPoE session ID.
OCT hwPPPoESmacSessionUserMac	1.3.6.1.4.1.2011.6.107.7.1.4	OCTET STRING	read-only	PPPoE SMAC user MAC address.
I32 hwPPPoESmacVlanID	1.3.6.1.4.1.2011.6.107.7.1.5	Integer32	read-only	PPPoE SMAC user VLAN.

RFC description

Huawei vendor-private MIB for managing PPPoE (Point-to-Point Protocol over Ethernet) on IP DSLAM devices.

Start monitoring Huawei IP DSLAM broadband access equipment (PPPoE intermediate agent/single-MAC) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-IPDSLAM-PPPOE-MIB

What Is HUAWEI-IPDSLAM-PPPOE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description