HP-SN-VSRP-MIB

All MIBs › HP-SN-VSRP-MIB

Category: Technology: High Availability, Vendor: HP/HPE

Description: HP ServerNet (Foundry-heritage) SNMP MIB for Virtual Switch Redundancy Protocol (VSRP) configuration and failover state on HP SN devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-SN-VSRP-MIB?

HP-SN-VSRP-MIB is an SNMP MIB inherited from HP's ServerNet (Foundry-heritage) product line, used to configure and monitor VSRP (Virtual Switch Redundancy Protocol), a first-hop redundancy protocol similar to VRRP, on HP SN switches. It exposes per-interface and per-virtual-router configuration and operational state, including group operating mode and interface limits on how many virtual router IDs can be configured. This MIB is directly relevant to hardware/software fault monitoring because VSRP governs failover behavior, and snVsrpIfStateChangeTrap notifies administrators in near real time when an interface's redundancy role changes (e.g., master to backup), which is a critical high-availability event. It functions similarly to, and can be considered a proprietary counterpart of, the standard VRRP-MIB, though it is not directly derived from it. It is typically deployed in networks requiring gateway redundancy, such as data center or campus core layers where two or more HP SN switches share a virtual IP for first-hop resiliency. Engineers can download the HP-SN-VSRP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-SN-VSRP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP SN switch/router (Foundry-heritage)

Monitoring Examples

The module exposes snVsrpIfTable and snVsrpVirRtrTable to hold per-interface and per-virtual-router VSRP state, alongside snVsrpGroupOperModeVsrp for the group's operating mode and snVsrpIfMaxNumVridPerIntf/snVsrpIfMaxNumVridPerSystem for configured VRID capacity limits. An administrator would primarily watch for snVsrpIfStateChangeTrap events, since an unexpected master-to-backup transition on a formerly master interface would indicate a failover has occurred, possibly due to a link or device failure. snVsrpClearVrrpStat would be used operationally to reset counters after investigating such an event.

What Can Be Monitored

VSRP interface/virtual-router state
master/backup role changes (failover events)
VRID capacity per interface and system
VSRP group operating mode

Imported Objects

From HP-SN-SWITCH-GROUP-MIB

snVsrp

OBJECT-IDENTITY

From RFC1155-SMI

Counter
IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
snVsrpGlobal	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1
INT snVsrpGroupOperModeVsrp	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1.1	INTEGER	read-write	The VSRP is configured on this system either enabled or disabled and thedefault is disabled mode. disabled(0)..........disable VSRP enabled(1)...........activate VSRP
INT snVsrpIfStateChangeTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1.2	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate VSRP interface state change traps.
INT snVsrpIfMaxNumVridPerIntf	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1.3	INTEGER	read-only	Indicates the maximum number of VRID per interface.
INT snVsrpIfMaxNumVridPerSystem	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1.4	INTEGER	read-only	Indicates the maximum number of VRID per system.
INT snVsrpClearVrrpStat	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.1.5	INTEGER	read-write	Clear VSRP statistics command.
snVsrpIfIntf	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2
snVsrpIfTable	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2.1		not-accessible	The VSRP Interface Table describes the interfaces from the viewpoint of VSRP.
snVsrpIfEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2.1.1		not-accessible	The VSRP Interface Entry describes one interface from the viewpoint of VSRP.
INT snVsrpIfVlanId	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2.1.1.1	INTEGER	read-only	Vlan index.
INT snVsrpIfAuthType	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2.1.1.2	INTEGER	read-write	The authentication type of this interface.
OCT snVsrpIfAuthPassword	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.2.1.1.3	OCTET STRING	read-write	The simple text password is allowed if only if the snVsrpIfAuthType type is simpleTextPasswd.
snVsrpVirRtr	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3
snVsrpVirRtrTable	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1		not-accessible	The vsrp virtual router Entry describes one virtual router from the viewpoint of vsrp.
snVsrpVirRtrEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1		not-accessible	The vsrp virtual router Entry describes one virtual router from the viewpoint of vsrp.
INT snVsrpVirRtrVlanId	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.1	INTEGER	read-only	Vlan index.
INT snVsrpVirRtrId	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.2	INTEGER	read-only	One of the virtual router ID of this vsrp interface.
INT snVsrpVirRtrOwnership	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.3	INTEGER	read-write	The ownership of this vsrp router interface can be set to backup(2). VirRtr SNMP-GET returns incomplete(0), it means no IP address has assigned to this vsrp router interface.
INT snVsrpVirRtrCfgPriority	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.4	INTEGER	read-write	The higher the number the higher the priority is. This parameter decides which backup router should becomes the Active Router for the interface. A backup Router with higher priority selected to becomes the Active Router. Therefore, this Object can be set if only if snVsrpVirRtrOwnership is set to backup(2).
INT snVsrpVirRtrTrackPriority	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.5	INTEGER	read-write	The higher the number the higher the priority is. after this object is configured, the snVsrpVirRtrCurrPriority of this interface will be adjusted dynamically with this track priority when the Track Port states first changes from UP to DOWN.
INT snVsrpVirRtrCurrPriority	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.6	INTEGER	read-only	The higher the number the higher the priority is. This object will be adjusted dynamically with the track priority when the Track Port states first changes from UP to DOWN.
INT snVsrpVirRtrHelloInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.7	INTEGER	read-write	Time interval between advertisements (seconds).
INT snVsrpVirRtrDeadInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.8	INTEGER	read-write	Dead interval (seconds).
INT snVsrpVirRtrPreemptMode	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.9	INTEGER	read-write	This mode controls whether a higher priority Backup router preempts a lower priority Master. The mode with enabled(1) allow preemption and disabled(0) prohibit preemption.
INT snVsrpVirRtrState	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.10	INTEGER	read-only	This object specifies the vsrp Router's interface state as: init(0)...initialization state. master(1)...master state. backup(2)...backup state.
OCT snVsrpVirRtrIpAddrMask	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.11	OCTET STRING	read-write	The numbers of IP Addresses of this virtual router of this interface, this holds good for L3 vsrp.
INT snVsrpVirRtrActivate	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.12	INTEGER	read-write	This object specifies the vsrp Router's activate command as: disabled(0)...deactivate this vsrp Router. enabled(1)....activate this vsrp Router.
OCT snVsrpVirRtrTrackPortList	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.13	OCTET STRING	read-write	This object specifies the identity of the physical port and virtual ports whose state is to be monitored. Each port index is an ifIndex, if there are consecutive 4 or more ifIndex then they will be encoded like below. Encoding and decoding scheme is range based: Each range prefix with 0000 (2 octets) where 0000 is not valid ifIndex. Next 2 octets indicates lower range ifIndex, followed by 2 octets of higher range ifIndex. Individual(non range) ones will be displayed as it is. Ex: port list: 0001..0005 0015 0032..0047 Port list in PDU: 0000 0001 0005 000f 0000 0020 002f. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The router VSRP physical track port membership.
INT snVsrpVirRtrAdvertiseBackup	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.14	INTEGER	read-write	Set Advertise this backup router to master
INT snVsrpVirRtrHoldDownInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.15	INTEGER	read-write	VSRP protection mechanism, an extra delay for a switch in backup mode to upgrade itself to master mode
INT snVsrpVirRtrInitTtl	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.16	INTEGER	read-write	VSRP:TTL in the hello packet to regulate the distance that a hello packet can travel. It prevents the flooding of VSRP hello packets in the network
OCT snVsrpVirRtrIncPortList	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.17	OCTET STRING	read-write	Include all free ports of the VLAN into its control ports
INT snVsrpVirRtrSave	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.18	INTEGER	read-write	Set VSRP to save current parameters value
INT snVsrpVirRtrBackupInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.19	INTEGER	read-write	Time interval between backup routers hello message advertisements (seconds).
INT snVsrpVirRtrRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.20	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an existing row VirRtr the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
CTR snVsrpVirRtrRxArpPktDropCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.21	Counter	read-only	The received vsrp ARP Packet Drop Counts.
CTR snVsrpVirRtrRxIpPktDropCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.22	Counter	read-only	The received VSRP IP Packet Drop Counts.
CTR snVsrpVirRtrRxPortMismatchCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.23	Counter	read-only	The received vsrp Port mismatching Counts.
CTR snVsrpVirRtrRxNumOfIpMismatchCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.24	Counter	read-only	The received VSRP Number of IP Addresses mismatching Counts.
CTR snVsrpVirRtrRxIpMismatchCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.25	Counter	read-only	The received vsrp IP Address mismatching Counts.
CTR snVsrpVirRtrRxHelloIntMismatchCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.26	Counter	read-only	The counts of the virtual router interface with hello interval mismatch counts.
CTR snVsrpVirRtrRxPriorityZeroFromMasterCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.27	Counter	read-only	The counts of the virtual router interface with Priority zero from the master.
CTR snVsrpVirRtrRxHigherPriorityCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.28	Counter	read-only	The counts of the virtual router interface with higher Priority.
CTR snVsrpVirRtrTransToMasterStateCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.29	Counter	read-only	The counts of the virtual router interface transition to master state.
CTR snVsrpVirRtrTransToBackupStateCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.30	Counter	read-only	The counts of the virtual router interface transition to backup state.
INT snVsrpVirRtrCurrDeadInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.31	INTEGER	read-only	Current Dead interval (in 100 milliseconds).
INT snVsrpVirRtrCurHelloInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.32	INTEGER	read-only	Set backup router hello interval
INT snVsrpVirRtrCurHoldDownInt	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.33	INTEGER	read-only	VSRP protection mechanism, an extra delay for a switch in backup mode to upgrade itself to master mode
INT snVsrpVirRtrCurInitTtl	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.34	INTEGER	read-only	VSRP:TTL in the hello packet to regulate the distance that a hello packet can travel. It prevents the flooding of VSRP hello packets in the network
MAC snVsrpVirRtrHelloMacAddress	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.35	MacAddress	read-only	Hello MAC address.
IP snVsrpVirRtrMasterIpAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.3.21.3.1.1.36	IpAddress	read-only	The master router's real/virtual (primary) IP address. This is the IP address listed as the source in vsrp advertisement last received by this virtual router.

RFC description

Foundry VSRP (Virtual Switch Routing Protocol) MIB for switch group management.

Start monitoring HP SN switch/router (Foundry-heritage, VSRP redundancy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-SN-VSRP-MIB

What Is HP-SN-VSRP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description