H3C-TRAP-MIB

All MIBs › H3C-TRAP-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2010-06-05

Category: Protocol: SNMP, Vendor: H3C/HH3C

Description: H3C MIB for SNMP trap management defining trap destinations, filter policies, and trap transmission configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is H3C-TRAP-MIB?

H3C-TRAP-MIB is a general-purpose H3C proprietary MIB governing SNMP trap behavior across the vendor's router and switch product lines, controlling trap destinations, filtering policies, and transmission parameters rather than modeling a specific feature's data. No runtime object names were extracted for this module, so its precise table structure can't be confirmed here, but per its description it applies broadly across "routers, switches and other products," with some objects being product-specific. As a trap-infrastructure MIB, its monitoring relevance is indirect: it configures how and where fault/event notifications are sent, underpinning the delivery of hardware and software status alerts from every other H3C MIB rather than exposing hardware sensors itself. It has an implicit dependency on standard SNMP notification mechanisms (SNMPv2-MIB/SNMP-TARGET-MIB conventions) that it customizes for H3C's needs. It's deployed across the full range of H3C routers and switches to centrally manage where and how the device's SNMP traps are delivered, a task governed by the H3C-TRAP-MIB MIB.

IPNetwork Monitor allows you to monitor SNMP objects defined in H3C-TRAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C routers
H3C switches
other H3C network products

Monitoring Examples

No sample objects were provided for this module, so specific table names can't be confirmed; based on its description, an administrator would typically configure trap destination addresses and filtering rules through this MIB and then verify that critical events (such as interface-down or environmental alarms surfaced by other MIBs) are correctly forwarded to the configured trap receivers, catching a misconfigured filter that silently suppresses important notifications.

Imported Objects

From HUAWEI-3COM-OID-MIB

h3cCommon

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TAddress
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
h3cTrap	1.3.6.1.4.1.2011.10.2.38			This MIB is applicable to routers, switches and other products. Some objects in this may be used only for some specific products, so users should refer to the related documents to acquire more detail information.
h3cTableGroup	1.3.6.1.4.1.2011.10.2.38.1
h3cMacTabStatGroup	1.3.6.1.4.1.2011.10.2.38.1.1
INT h3cMacTabTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.1.1	INTEGER	read-write	Indicates whether h3cMacTabFullTrap and h3cMacTabAlmostFullTrap traps should be generated when the MAC table is filled.
I32 h3cMacTabTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.1.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the MAC table is full or two traps which occur when the MAC table is almost full.
h3cMacTabTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.1.3
I32 h3cMacTabLen	1.3.6.1.4.1.2011.10.2.38.1.1.3.1	Integer32	accessible-for-notify	The length of the MAC table.
h3cMacTabTrap	1.3.6.1.4.1.2011.10.2.38.1.1.4
NTF h3cMacTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.1.4.1			Send this trap when the MAC table is filled. The interval between two traps generated should be longer than h3cMacTabTrapInterval.
NTF h3cMacTabAlmostFullTrap	1.3.6.1.4.1.2011.10.2.38.1.1.4.2			Send this trap when the MAC table is almost full. The interval between two traps generated should be longer than h3cMacTabTrapInterval.
h3cArpTabStatGroup	1.3.6.1.4.1.2011.10.2.38.1.2
INT h3cArpTabTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.2.1	INTEGER	read-write	Indicates whether h3cArpTabFullTrap traps should be generated when the ARP table is filled.
I32 h3cArpTabTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.2.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the ARP table is filled.
h3cArpTabTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.2.3
I32 h3cArpTabLen	1.3.6.1.4.1.2011.10.2.38.1.2.3.1	Integer32	accessible-for-notify	The length of the ARP table.
h3cArpTabTrap	1.3.6.1.4.1.2011.10.2.38.1.2.4
NTF h3cArpTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.2.4.1			Send this trap when the ARP table is filled. The interval between two traps generated should be longer than h3cArpTabTrapInterval.
NTF h3cArpPortDynamicEntryFullTrap	1.3.6.1.4.1.2011.10.2.38.1.2.4.2			Send this trap when the dynamic ARP number of the port exceeds the limitation. The object h3cArpTabLen describes the limitation of the max dynamic ARP number of this port. The interval between two traps should be longer than h3cArpTabTrapInterval.
h3cRtTabStatGroup	1.3.6.1.4.1.2011.10.2.38.1.3
h3cDetailRtTrapTable	1.3.6.1.4.1.2011.10.2.38.1.3.1		not-accessible	This table contains objects to decide what kind of trap should be sent.
h3cDetailRtTrapEntry	1.3.6.1.4.1.2011.10.2.38.1.3.1.1		not-accessible	Entry items
INT h3cDetailRtProType	1.3.6.1.4.1.2011.10.2.38.1.3.1.1.1	INTEGER	accessible-for-notify	The index value which uniquely identifies an entry in the h3cDetailRtTrapTable.
INT h3cDetailRtEnable	1.3.6.1.4.1.2011.10.2.38.1.3.1.1.2	INTEGER	read-write	Indicates whether h3cDetailRtTabFullTrap traps should be generated when a specific routing table is filled.
INT h3cRtTabTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.3.2	INTEGER	read-write	Indicates whether h3cRtTabFullTrap traps should be generated when the routing table is filled.
I32 h3cRtTabTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.3.3	Integer32	read-write	Definition of the minimum interval between two traps which occur when the routing table is filled.
h3cRtTabTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.3.4
I32 h3cRtTabLen	1.3.6.1.4.1.2011.10.2.38.1.3.4.1	Integer32	accessible-for-notify	The length of the routing table. The detail routing tables also use the same object.
IPt h3cDefaultRtNextHopType	1.3.6.1.4.1.2011.10.2.38.1.3.4.2	InetAddressType	accessible-for-notify	The IP address type of the next hop of the default route. The value must be ipv4 or ipv6
IP h3cDefaultRtNextHop	1.3.6.1.4.1.2011.10.2.38.1.3.4.3	InetAddress	accessible-for-notify	The IP address of the next hop of the default route.
NUM h3cDefaultRtOutIf	1.3.6.1.4.1.2011.10.2.38.1.3.4.4	InterfaceIndex	accessible-for-notify	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
h3cRtTabTrap	1.3.6.1.4.1.2011.10.2.38.1.3.5
NTF h3cRtTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.3.5.1			Send this trap when the routing table is filled. The interval between two traps generated should be longer than h3cRtTabTrapInterval.
NTF h3cDetailRtTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.3.5.2			Send this trap when the detail routing table is filled. The interval between two traps generated should be longer than h3cRtTabTrapInterval.
NTF h3cDefaultRtDelTrap	1.3.6.1.4.1.2011.10.2.38.1.3.5.3			Send this trap when the default route is deleted.
T/F h3cDefaultRtDelTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.3.6	TruthValue	read-write	Indicates whether h3cDefaultRtDelTrap traps should be generated when the default route is deleted.
h3cMulticastTabStatGroup	1.3.6.1.4.1.2011.10.2.38.1.4
INT h3cMulticastTabTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.4.1	INTEGER	read-write	Indicates whether h3cMulticastTabFullTrap traps should be generated when the multicast table is filled.
I32 h3cMulticastTabTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.4.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the multicast table is filled.
h3cMulticastTabTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.4.3
INT h3cMulticastTabType	1.3.6.1.4.1.2011.10.2.38.1.4.3.1	INTEGER	accessible-for-notify	Defining the type of the multicast table, layer2 or layer3.
I32 h3cMulticastTabLen	1.3.6.1.4.1.2011.10.2.38.1.4.3.2	Integer32	accessible-for-notify	The length of the multicast table.
h3cMulticastTabTrap	1.3.6.1.4.1.2011.10.2.38.1.4.4
NTF h3cMulticastTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.4.4.1			Send this trap when the multicast table is filled. The interval between two traps generated should be longer than h3cMulticastTabTrapInterval.
h3cNdTabStatGroup	1.3.6.1.4.1.2011.10.2.38.1.5
INT h3cNdTabTrapEnable	1.3.6.1.4.1.2011.10.2.38.1.5.1	INTEGER	read-write	Indicates whether h3cNdTabFullTrap traps should be generated when the ND table is filled.
I32 h3cNdTabTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.5.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the ND table is filled.
h3cNdTabTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.5.3
I32 h3cNdTabLen	1.3.6.1.4.1.2011.10.2.38.1.5.3.1	Integer32	accessible-for-notify	The length of the ND table.
h3cNdTabTrap	1.3.6.1.4.1.2011.10.2.38.1.5.4
NTF h3cNdTabFullTrap	1.3.6.1.4.1.2011.10.2.38.1.5.4.1			Send this trap when the ND table is filled. The interval between two traps generated should be longer than h3cNdTabTrapInterval.
h3cPeriodicalTrapGroup	1.3.6.1.4.1.2011.10.2.38.1.6
h3cPeriodicalTrapObjects	1.3.6.1.4.1.2011.10.2.38.1.6.1
I32 h3cPeriodicalTrapInterval	1.3.6.1.4.1.2011.10.2.38.1.6.1.1	Integer32	read-write	Definition of the periodical interval. If no trap occurs during the certain interval, an h3cPeriodicalTrap will be generated. If the interval is set to 0, no h3cPeriodicalTrap will be generated.
INT h3cPeriodicalTrapSwitch	1.3.6.1.4.1.2011.10.2.38.1.6.1.2	INTEGER	read-write	Definition of the periodical switch. If the value is off,the h3cPeriodicalTrap will not be generated. the h3cPeriodicalTrapInterval will be set to 0.
h3cPeriodicalTrapInfo	1.3.6.1.4.1.2011.10.2.38.1.6.2
h3cPeriodicalNotification	1.3.6.1.4.1.2011.10.2.38.1.6.3
h3cPeriodicalNotificationPrefix	1.3.6.1.4.1.2011.10.2.38.1.6.3.0
NTF h3cPeriodicalTrap	1.3.6.1.4.1.2011.10.2.38.1.6.3.0.1			If no trap occurs during the interval spicified by h3cPeriodicalTrapInterval, an h3cPeriodicalTrap will be generated. If the interval is set to 0, no h3cPeriodicalTrap will be generated.
h3cTrapDesInfo	1.3.6.1.4.1.2011.10.2.38.1.7
h3cTrapDesInfoTable	1.3.6.1.4.1.2011.10.2.38.1.7.1		not-accessible	A table of trap destination host address and port .
h3cTrapDesInfoEntry	1.3.6.1.4.1.2011.10.2.38.1.7.1.1		not-accessible	The entry of trap destination host address and port.
I32 h3cTrapDesInfoIndex	1.3.6.1.4.1.2011.10.2.38.1.7.1.1.1	Integer32	not-accessible	The index of this table.
IP h3cTrapDesIPAddress	1.3.6.1.4.1.2011.10.2.38.1.7.1.1.2	IpAddress	read-create	The host IP address of the trap destination.
I32 h3cTrapDesPort	1.3.6.1.4.1.2011.10.2.38.1.7.1.1.3	Integer32	read-create	The port of the trap destination.
ROW h3cTrapDesRowStatus	1.3.6.1.4.1.2011.10.2.38.1.7.1.1.4	RowStatus	read-create	The status of this table entry.
ADR h3cTrapDesAddrTAddress	1.3.6.1.4.1.2011.10.2.38.1.7.1.1.5	TAddress	read-create	This object contains a transport address.
h3cTrapConfig	1.3.6.1.4.1.2011.10.2.38.1.8
h3cTrapConfigTable	1.3.6.1.4.1.2011.10.2.38.1.8.1		not-accessible	A table of trap configuration.
h3cTrapConfigEntry	1.3.6.1.4.1.2011.10.2.38.1.8.1.1		not-accessible	The entry of trap configuration.
I32 h3cTrapConfigIndex	1.3.6.1.4.1.2011.10.2.38.1.8.1.1.1	Integer32	not-accessible	The index of this table.
STR h3cTrapConfigName	1.3.6.1.4.1.2011.10.2.38.1.8.1.1.2	SnmpAdminString	read-only	The name of the appointed traps.
STR h3cTrapConfigDescr	1.3.6.1.4.1.2011.10.2.38.1.8.1.1.3	SnmpAdminString	read-write	The description of the appointed traps.
INT h3cTrapConfigSwitch	1.3.6.1.4.1.2011.10.2.38.1.8.1.1.4	INTEGER	read-write	Indicates whether the appointed traps should be generated.

RFC description

H3C enterprise trap management MIB for routers, switches, and other network devices to generate notifications and alerts.

Start monitoring H3C router/switch (SNMP trap destination/filtering config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download H3C-TRAP-MIB

What Is H3C-TRAP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description