H3C-EPON-UNI-MIB

All MIBs › H3C-EPON-UNI-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2008-07-28

Category: Technology: EPON/PON, Vendor: H3C/HH3C

Description: H3C MIB for EPON User-Network Interface (UNI) management configuring subscriber-facing ports on EPON ONUs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is H3C-EPON-UNI-MIB?

H3C-EPON-UNI-MIB is an H3C enterprise MIB for managing the User-Network Interface (UNI) ports on an Ethernet Passive Optical Network (EPON) Optical Network Unit (ONU) — the subscriber-facing Ethernet ports through which end-user traffic enters the fiber access network. It belongs to the passive-optical-network/fiber-access technology area and exposes per-UNI-port configuration: administrative status, description, VLAN mode, access VLAN and trunk PVID, and the allowed VLAN range for trunk ports, plus port priority and MDI setting. It supports software/configuration status monitoring by letting an operator confirm each subscriber port is administratively up, correctly assigned to its VLAN, and configured with the intended trunk-allowed VLAN range, useful when diagnosing a subscriber connectivity or VLAN-tagging problem. It is one piece of H3C's broader EPON MIB suite, paired with an OLT-side counterpart, and depends on standard 802.1Q VLAN concepts. It is typically deployed on H3C ONUs at the customer premises within a carrier or enterprise fiber access deployment. Engineers can download the H3C-EPON-UNI-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in H3C-EPON-UNI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C EPON Optical Network Unit (ONU)

Monitoring Examples

An operator polls the h3cEponUniSysManTable/h3cEponUniSysManEntry rows, indexed by h3cEponUniIndex, to check h3cEponUniAdminStatus and h3cEponUniDescr for each subscriber port, confirming the port is administratively enabled and correctly labeled. Checking h3cEponUniVlanType, h3cEponUniAccessVlan, and h3cEponUniTrunkPvid reveals whether a port is configured as access or trunk and which VLAN it carries. The h3cEponUniVLANTrunkAllowListLow and h3cEponUniVLANTrunkAllowListHigh objects define the allowed VLAN range on a trunk UNI port, which an operator would check if tagged traffic is unexpectedly being dropped.

What Can Be Monitored

UNI port admin status
UNI port VLAN mode (access/trunk)
access VLAN / trunk PVID assignment
allowed VLAN range on trunk ports
UNI port priority and MDI setting

Imported Objects

From HUAWEI-3COM-OID-MIB

h3cEpon

OBJECT-IDENTITY

From IF-MIB

ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
h3cEponUni	1.3.6.1.4.1.2011.10.2.42.5			The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
h3cEponUniSysMan	1.3.6.1.4.1.2011.10.2.42.5.1
h3cEponUniSysManTable	1.3.6.1.4.1.2011.10.2.42.5.1.1		not-accessible	This table defines several UNI system parameters.
h3cEponUniSysManEntry	1.3.6.1.4.1.2011.10.2.42.5.1.1.1		not-accessible	The entry of h3cEponUniSysManTable.
I32 h3cEponUniIndex	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.1	Integer32	accessible-for-notify	The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
OCT h3cEponUniDescr	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.2	OCTET STRING	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
INT h3cEponUniAdminStatus	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.3	INTEGER	read-write	The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, h3cEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
INT h3cEponUniMdi	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.4	INTEGER	read-write	Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
I32 h3cEponUniPriority	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.5	Integer32	read-write	The priority of user network interface. If the value is larger, the priority will be higher.
INT h3cEponUniVlanType	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.6	INTEGER	read-write	UNI vlan types.
I32 h3cEponUniAccessVlan	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.7	Integer32	read-write	The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
INT h3cEponUniTrunkPvid	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.8	INTEGER	read-write	PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
OCT h3cEponUniVLANTrunkAllowListLow	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.9	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
OCT h3cEponUniVLANTrunkAllowListHigh	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.10	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
I32 h3cEponUniInboundLineRate	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.11	Integer32	read-write	The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of h3cEponUniLineRateMax in the entry. It must be multiple of the value of h3cEponUniLineRateStep. The default value of h3cEponUniLineRate is the value of h3cEponUniLineRateMax.
I32 h3cEponUniOutboundLineRate	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.12	Integer32	read-write	The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of h3cEponUniLineRateMax in the entry. It must be multiple of the value of h3cEponUniLineRateStep. The default value of h3cEponUniLineRate is the value of h3cEponUniLineRateMax.
T/F h3cEponUniFlowControl	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.13	TruthValue	read-write	Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
INT h3cEponUniSpeed	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.14	INTEGER	read-write	User network interface speed.
INT h3cEponUniDuplex	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.15	INTEGER	read-write	User network interface mode.
T/F h3cEponUniVlanVPNStatus	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.16	TruthValue	read-write	vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
INT h3cEponUniCountReset	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.17	INTEGER	read-write	Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
INT h3cEponUniPortIsolate	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.18	INTEGER	read-write	enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
OCT h3cEponUniVlanConfiguration	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.23	OCTET STRING	read-write	The vlan configuration of the related vlan mode. Transparent vlan mode: h3cEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
INT h3cEponUniAutoNegotiation	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.25	INTEGER	read-write	enable - enable auto negotiation. disable - disable auto negotiation.
INT h3cEponUniRestartAutoNeg	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.26	INTEGER	read-write	Force to restart the auto negotiation process.
INT h3cEponUniLinkStatus	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.29	INTEGER	read-only	The link status of UNI.
INT h3cEponUniInterfaceType	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.30	INTEGER	read-only	UNI interface type.
INT h3cEponUniVitualCableTest	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.31	INTEGER	read-write	True(1): Virtual cable test enable. False(2): Virtual cable test disable.
INT h3cEponUniVCTCableStatus	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.32	INTEGER	read-only	Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
I32 h3cEponUniVCTCableLength	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.33	Integer32	read-only	Get the cable length. When h3cEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When h3cEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
INT h3cEponUniVCTImpedanceMismatch	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.34	INTEGER	read-only	Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
I32 h3cEponUniVCTPairSkew	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.35	Integer32	read-only	Get the symmetry of cable. If the function is not supported , the default value 0 will be returned. Unit:nanosecond(ns).
INT h3cEponUniVCTPairSwap	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.36	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
INT h3cEponUniVCTPolaritySwap	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.37	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
I32 h3cEponUniVCTInsertionLoss	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.38	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
I32 h3cEponUniVCTReturnLoss	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.39	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
I32 h3cEponUniVCTNearendCrosstalk	1.3.6.1.4.1.2011.10.2.42.5.1.1.1.40	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
h3cEponUniCountTable	1.3.6.1.4.1.2011.10.2.42.5.1.2		not-accessible	A list of interface counter about frames entries.
h3cEponUniCountEntry	1.3.6.1.4.1.2011.10.2.42.5.1.2.1		not-accessible	An entry containing management information applicable to a particular interface.
U32 h3cEponUniInStatsPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.1	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
U32 h3cEponUniInStatsUnicastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.2	Unsigned32	read-only	The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 h3cEponUniInStatsBroadcastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.3	Unsigned32	read-only	The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
U32 h3cEponUniInStatsMulticastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.4	Unsigned32	read-only	The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 h3cEponUniInPausePkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.5	Unsigned32	read-only	A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 h3cEponUniInTotalErrors	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.6	Unsigned32	read-only	Total count of the error frames received on this interface.
U32 h3cEponUniInStatsCRCAlignErrors	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.7	Unsigned32	read-only	The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
U32 h3cEponUniInStatsUndersizePkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.8	Unsigned32	read-only	The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 h3cEponUniInStatsOversizePkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.9	Unsigned32	read-only	The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 h3cEponUniInErrorbyOther	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.10	Unsigned32	read-only	The total number of error frames received on this interface.
U32 h3cEponUniOutStatsPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.11	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
U32 h3cEponUniOutStatsUnicastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.12	Unsigned32	read-only	The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 h3cEponUniOutStatsBroadcastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.13	Unsigned32	read-only	The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
U32 h3cEponUniOutStatsMulticastPkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.14	Unsigned32	read-only	The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 h3cEponUniOutStatsPausePkts	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.15	Unsigned32	read-only	The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 h3cEponUniOutTotalErrors	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.16	Unsigned32	read-only	The total number of error frames sent on this interface.
U32 h3cEponUniOutStatsCollisions	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.17	Unsigned32	read-only	The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
U32 h3cEponUniOutDelayExceededDiscards	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.18	Unsigned32	read-only	The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
U32 h3cEponUniOutErrorbyOther	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.19	Unsigned32	read-only	The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
U32 h3cEponUniOutDroppedFrames	1.3.6.1.4.1.2011.10.2.42.5.1.2.1.20	Unsigned32	read-only	The total number of frames dropped because of buffer failure.
h3cEponUniIgmpInfoTable	1.3.6.1.4.1.2011.10.2.42.5.1.3		not-accessible	This table stores igmp information of UNI interface.
h3cEponUniIgmpInfoEntry	1.3.6.1.4.1.2011.10.2.42.5.1.3.1		not-accessible	The entry of h3cEponUniIgmpInfoTable.
I32 h3cEponUniMacIndex	1.3.6.1.4.1.2011.10.2.42.5.1.3.1.1	Integer32	not-accessible	The index uniquely identifies the igmp information in current UNI interface.
MAC h3cEponUniIgmpMacAddress	1.3.6.1.4.1.2011.10.2.42.5.1.3.1.2	MacAddress	read-only	A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
I32 h3cEponUniIgmpVlanId	1.3.6.1.4.1.2011.10.2.42.5.1.3.1.3	Integer32	read-only	An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
h3cEponUniParaMan	1.3.6.1.4.1.2011.10.2.42.5.1.4
I32 h3cEponUniLineRateMax	1.3.6.1.4.1.2011.10.2.42.5.1.4.1	Integer32	read-only	The maximum value of the line-rate(kbps) that user network interface can be set.
I32 h3cEponUniLineRateStep	1.3.6.1.4.1.2011.10.2.42.5.1.4.2	Integer32	read-only	The step of line-rate(kbps).
I32 h3cEponUniNumberOnOnu	1.3.6.1.4.1.2011.10.2.42.5.1.4.3	Integer32	read-only	The user network interface number on ONU.
h3cEponUniScalarGroup	1.3.6.1.4.1.2011.10.2.42.5.1.5
h3cEponUniPortPolicyTable	1.3.6.1.4.1.2011.10.2.42.5.1.6		not-accessible	UNI port policy configuration.
h3cEponUniPortPolicyEntry	1.3.6.1.4.1.2011.10.2.42.5.1.6.1		not-accessible	The entry of h3cEponUniPortPolicyTable.
INT h3cEponUniPortPolicyStatus	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.1	INTEGER	read-write	enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
I32 h3cEponUniPortPolicyCir	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.2	Integer32	read-write	The committed information rate, ranging from 1 to 102400, measured in kbps.
I32 h3cEponUniPortPolicyBucketDepth	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.3	Integer32	read-write	The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 h3cEponUniPortPolicyExtraBurst	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.4	Integer32	read-write	The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 h3cEponUniPortPolicyInboundCir	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.5	Integer32	read-write	The inbound committed information rate, measured in kbps.
I32 h3cEponUniPortPolicyInboundBucketDepth	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.6	Integer32	read-write	The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 h3cEponUniPortPolicyInboundExtraBurst	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.7	Integer32	read-write	The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 h3cEponUniPortPolicyOutboundCir	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.8	Integer32	read-write	The outbound committed information rate, stepped by 64, measured in kbps.
I32 h3cEponUniPortPolicyOutboundPir	1.3.6.1.4.1.2011.10.2.42.5.1.6.1.9	Integer32	read-write	The outbound peak information rate, stepped by 64, measured in kbps.
h3cEponUniMulticastTable	1.3.6.1.4.1.2011.10.2.42.5.1.7		not-accessible	UNI multicast configuration.
h3cEponUniMulticastEntry	1.3.6.1.4.1.2011.10.2.42.5.1.7.1		not-accessible	The entry of h3cEponUniPortPolicyTable.
I32 h3cEponUniMulticastGroupNumber	1.3.6.1.4.1.2011.10.2.42.5.1.7.1.1	Integer32	read-write	The allowed multicast group number that can be handled at the same time by UNI.
OCT h3cEponUniMulticastVlanList	1.3.6.1.4.1.2011.10.2.42.5.1.7.1.2	OCTET STRING	read-write	The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
INT h3cEponUniMulticastStripStatus	1.3.6.1.4.1.2011.10.2.42.5.1.7.1.3	INTEGER	read-write	true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
T/F h3cEponUniMulticastFastleave	1.3.6.1.4.1.2011.10.2.42.5.1.7.1.4	TruthValue	read-write	true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
h3cEponUniTechAbilityTable	1.3.6.1.4.1.2011.10.2.42.5.1.8		not-accessible	UNI multicast configuration.
h3cEponUniTechAbilityEntry	1.3.6.1.4.1.2011.10.2.42.5.1.8.1		not-accessible	The entry of h3cEponUniTechAbilityTable.
OCT h3cEponUniLocalTechAbility	1.3.6.1.4.1.2011.10.2.42.5.1.8.1.1	OCTET STRING	read-only	The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
OCT h3cEponUniAdvertisedTechAbility	1.3.6.1.4.1.2011.10.2.42.5.1.8.1.2	OCTET STRING	read-only	The advertised port capabilities of the UNI. The capabilities list references the description of h3cEponUniLocalTechAbility.
h3cEponUniMulticastControlTable	1.3.6.1.4.1.2011.10.2.42.5.1.9		not-accessible	UNI multicast control parameters.
h3cEponUniMulticastControlEntry	1.3.6.1.4.1.2011.10.2.42.5.1.9.1		not-accessible	The entry of the table h3cEponUniMulticastControlTable.
I32 h3cEponUniMulticastVlanIndex	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.1	Integer32	read-create	The multicast vlan ID.
OCT h3cEponUniMulticastAddressList	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.2	OCTET STRING	read-create	The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
INT h3cEponUniMulticastAccessRule	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.3	INTEGER	read-create	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 h3cEponUniMulticastChannelLimit	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.4	Integer32	read-create	The limitation of multicast preview channel number.
I32 h3cEponUniMulticastPreTimeSlice	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.5	Integer32	read-create	The time slice of multicast preview.
I32 h3cEponUniMulticastPreTimes	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.6	Integer32	read-create	The number of multicast preview times.
I32 h3cEponUniMulticastPreInterval	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.7	Integer32	read-create	The interval between two consecutive previews, measured in minute.
ROW h3cEponUniMulticastRowStatus	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.8	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
INT h3cEponUniMulticastIndex	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.9	INTEGER	not-accessible	The index of the entry.
OCT h3cEponUniMulticastSourceIpList	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.10	OCTET STRING	read-create	This list contains many source ip addresses. Each ip address is contained in four octets.
I32 h3cEponUniMulticastResetInterval	1.3.6.1.4.1.2011.10.2.42.5.1.9.1.11	Integer32	read-create	The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
h3cEponUniQosIndexNextTable	1.3.6.1.4.1.2011.10.2.42.5.1.10		not-accessible	The next index table.
h3cEponUniQosIndexNextEntry	1.3.6.1.4.1.2011.10.2.42.5.1.10.1		not-accessible	The entry of the table h3cEponUniQosIndexNextTable.
I32 h3cEponUniQosConfIndexNext	1.3.6.1.4.1.2011.10.2.42.5.1.10.1.1	Integer32	read-only	This object contains an appropriate value to be used for h3cEponUniQosConfIndex when creating rows in the h3cEponUniQosConfTable.
h3cEponUniQosConfTable	1.3.6.1.4.1.2011.10.2.42.5.1.11		not-accessible	UNI Qos configuration.
h3cEponUniQosConfEntry	1.3.6.1.4.1.2011.10.2.42.5.1.11.1		not-accessible	The entry of the table h3cEponUniQosConfTable.
I32 h3cEponUniQosConfIndex	1.3.6.1.4.1.2011.10.2.42.5.1.11.1.1	Integer32	not-accessible	The rule index.
I32 h3cEponUniQosConfRuleIndexNext	1.3.6.1.4.1.2011.10.2.42.5.1.11.1.2	Integer32	read-only	This object contains an appropriate value to be used for h3cEponUniQosRuleIndex when creating rows in the h3cEponUniQosRuleTable.
I32 h3cEponUniQosConfMappedQueue	1.3.6.1.4.1.2011.10.2.42.5.1.11.1.3	Integer32	read-create	The queue that the ethernet frames will be mapped.
I32 h3cEponUniQosConfMarkedPriority	1.3.6.1.4.1.2011.10.2.42.5.1.11.1.4	Integer32	read-create	Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
ROW h3cEponUniQosConfRowStatus	1.3.6.1.4.1.2011.10.2.42.5.1.11.1.5	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
h3cEponUniQosRuleTable	1.3.6.1.4.1.2011.10.2.42.5.1.12		not-accessible	Qos sub rule of the UNI.
h3cEponUniQosRuleEntry	1.3.6.1.4.1.2011.10.2.42.5.1.12.1		not-accessible	The entry of the table h3cEponUniQosRuleTable.
I32 h3cEponUniQosRuleIndex	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.1	Integer32	not-accessible	The sub rule index.
INT h3cEponUniQosRuleSelector	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.2	INTEGER	read-create	The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
I32 h3cEponUniQosRuleValue	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.3	Integer32	read-create	The rule value based on the h3cEponUniQosRuleSelector.
MAC h3cEponUniQosRuleMacAddress	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.4	MacAddress	read-create	MAC Address.
INT h3cEponUniQosRuleOperator	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.5	INTEGER	read-create	nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
ROW h3cEponUniQosRuleRowStatus	1.3.6.1.4.1.2011.10.2.42.5.1.12.1.6	RowStatus	read-create	The status of this table entry. Only active, createAndGo and the destory are supported.
h3cEponUniMirrorGroupTable	1.3.6.1.4.1.2011.10.2.42.5.1.13		not-accessible	Qos sub rule of the UNI.
h3cEponUniMirrorGroupEntry	1.3.6.1.4.1.2011.10.2.42.5.1.13.1		not-accessible	The entry of the h3cEponUniMirrorGroupTable.
I32 h3cEponUniMirrorGroupID	1.3.6.1.4.1.2011.10.2.42.5.1.13.1.1	Integer32	not-accessible	Epon UNI mirror group ID.
OCT h3cEponUniMirrorInboundPortList	1.3.6.1.4.1.2011.10.2.42.5.1.13.1.2	OCTET STRING	read-write	UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
OCT h3cEponUniMirrorOutboundPortList	1.3.6.1.4.1.2011.10.2.42.5.1.13.1.3	OCTET STRING	read-create	UNI outnbound port list, more infomation reference h3cEponUniMirrorInboundPortList
I32 h3cEponUniMonitorPort	1.3.6.1.4.1.2011.10.2.42.5.1.13.1.4	Integer32	read-create	UNI monitor port.
ROW h3cEponUniMirrorRowStatus	1.3.6.1.4.1.2011.10.2.42.5.1.13.1.5	RowStatus	read-create	RowStatus, Now support three status: createAndGo, active, destroy.
h3cEponUniMirrorGroupIdNextTable	1.3.6.1.4.1.2011.10.2.42.5.1.14		not-accessible	The next index table, which is used by h3cEponUniMirrorGroupTable.
h3cEponUniMirrorGroupIdNextEntry	1.3.6.1.4.1.2011.10.2.42.5.1.14.1		not-accessible	The entry of the table h3cEponUniMirrorGroupIdNextEntry.
I32 h3cEponUniMirrorGroupIDNext	1.3.6.1.4.1.2011.10.2.42.5.1.14.1.1	Integer32	read-only	This object contains an appropriate value to be used for h3cEponUniMirrorGroupID when creating rows in the h3cEponUniMirrorGroupTable.
h3cEponUniMulticastCtrlInfoTable	1.3.6.1.4.1.2011.10.2.42.5.1.15		not-accessible	UNI multicast information which is active .
h3cEponUniMulticastCtrlInfoEntry	1.3.6.1.4.1.2011.10.2.42.5.1.15.1		not-accessible	The entry of the table h3cEponUniMulticastCtrlInfoTable.
I32 h3cEponUniMultActVlan	1.3.6.1.4.1.2011.10.2.42.5.1.15.1.1	Integer32	not-accessible	The multicast vlan ID which is active.
IP h3cEponUniMultActAddress	1.3.6.1.4.1.2011.10.2.42.5.1.15.1.2	IpAddress	not-accessible	The multicast address which is active.
INT h3cEponUniMultActAccessRule	1.3.6.1.4.1.2011.10.2.42.5.1.15.1.3	INTEGER	read-only	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 h3cEponUniMultActPreTimes	1.3.6.1.4.1.2011.10.2.42.5.1.15.1.4	Integer32	read-only	The number of multicast preview times which is active.
I32 h3cEponUniMultActPreRemain	1.3.6.1.4.1.2011.10.2.42.5.1.15.1.5	Integer32	read-only	The remanent time slice of multicast preview which is active.
h3cEponUniMulticastIndexNextTable	1.3.6.1.4.1.2011.10.2.42.5.1.16		not-accessible	The next index table, which is used by h3cEponUniMulticastControlTable.
h3cEponUniMulticastIndexNextEntry	1.3.6.1.4.1.2011.10.2.42.5.1.16.1		not-accessible	The entry of the table h3cEponUniMulticastIndexNextEntry.
I32 h3cEponUniMulticastConfIndexNext	1.3.6.1.4.1.2011.10.2.42.5.1.16.1.1	Integer32	read-only	This object contains an appropriate value to be used for h3cEponUniMulticastIndex when creating rows in the h3cEponUniMulticastControlTable.
h3cEponUniTrap	1.3.6.1.4.1.2011.10.2.42.5.2
h3cEponUniTrapPrefix	1.3.6.1.4.1.2011.10.2.42.5.2.0
NTF h3cEponUniLinkUpTrap	1.3.6.1.4.1.2011.10.2.42.5.2.0.1			A h3cEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
NTF h3cEponUniLinkDownTrap	1.3.6.1.4.1.2011.10.2.42.5.2.0.2			A h3cEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.

RFC description

H3C Ethernet Passive Optical Network (EPON) User Network Interface (UNI) MIB. Provides SNMP management objects for configuring and monitoring user-facing interfaces on EPON optical network terminals (ONUs) based on IEEE 802.3ah EFM PON standards.

Start monitoring H3C EPON ONU (subscriber-facing UNI port config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download H3C-EPON-UNI-MIB

What Is H3C-EPON-UNI-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description